CERTAIN B/R AND E/M SANCTIONED WORKS AT MIL STATION BHUSAWAL UNDER GE (S) AHILYANAGAR

Amount

Excavation in trenches not exc 1.50m wide and not exc 1.50m deep for foundation, laying of pipes, cables or for shafts, wells cesspits, man holes, valve pits etc not exc 10 Sqm on plan and n exc 1.5m in depth and getting out in any type of soil complete all as specified and as directed.

All as per item No. 1 above but depth exc 1.5m but not exc 3.0 m deep complete all as specified and as directed.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in any type of soil complete all as specified and directed.

Removing excavated material (soil) n.exc. 50m and depositing where directed at a level n.exc. 1.5m above the starting point complete all as specified and as directed.

Taking up or down unserviceable CI/DI water mains 150 mm bore including all fittings complete from trenches complete all as specified and as directed

Taking up or down unserviceable CI/DI water mains 200 mm bore including all fittings complete from trenches complete all as specified and as directed

Supply, laying, jointing and testing of ductile iron pipes with spigot and socket ends, centrifugally cast, class -K 7, conforming to IS 8329 of 150 mm bore in any length, laid in trenchs/ pipe support etc, pressure testing after laying complete as per IS- 12288 including styrene butadiene rubber gasket joints complete all as specified and as directed by Engr-in-Charge. Note:- Tyton joints required are deemed to be included in the unit rate quoted.

Taking up or down old rusted and unserviceable GI water tubing 50 mm bore including all fittings complete from walls /floor or trenches all as specified and as directed.

All as per serial item No. 8 here-in-before but 40 mm bore pipe.

All as per serial item No. 8 here-in-before but 25 mm bore pipe.

All as per serial item No. 8 here-in-before but 20 mm bore pipe.

S&F steel water tubing, galvanised iron, 50 mm bore, medium grade in any length, including necessary fittings, fixed complete to wall and ceiling or laid in trench, floors etc including jointing, testing and connections complete all as specified and as directed. Note : Excavation and earth work shall be measured and paid separately.

All as per serial item No 12 here-in-before but GI Pipe of size 40 mm dia

All as per serial item No 12 here-in-before but GI Pipe of size 25 mm dia

All as per serial item No 12 here-in-before but GI Pipe of size 20 mm dia

S & F in repairs 50 mm bore gate valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or unions and fixed complete all as specified and as directed.

All as per serial item No 16 here-in-before but of size 40 mm dia

All as per serial item No 16 here-in-before but of size 25 mm dia

All as per serial item No 16 here-in-before but of size 20 mm dia

S & F in replacement sluice valve of size 150 mm bore, cast iron, long body, both ends flanged as per IS-14846 and drilled with stainless steel spindle iron wheel head and as per pressure rating PN 1.6, Class I, ISI Marked alongwith nuts, bolts, washers , gaskets etc. incl taking out old/ UNSV sluice valve from valve chamber / trenches complete all as specified and as directed.

M&L for construction of valve pit/chamber of Internal dimensions 900 mm x 900 mm x 1200 mm, using PCC 1:4:8, type D-2, using 40mm graded stone aggregates for foundation, 23 cm thick, brick wall built in cement mortar (1:4) ,15 mm thick rendering all around the brick work in cement mortar (1:6), 75 mm thick PCC (1:2:4) type B-1 using 20mm graded stone aggregates in coping including necessary form work, 3 coats of white wash on rendered surfaces and on coping, 2 mm thick mild steel top sheet cover with frame made out of 40x40x6 mm angle iron, locking arrangement, including painting of steel surface with two coats of black bituminous paint over a coat of red oxide primer including demolition of existing valve chamber and clearing the debris complete all as specified and as directed.

All as per serial item No 21 here-in-before but internal dimensions 450 mm x 450 mm x 600 mm

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position (reinforcement cut to facilitate demolition) not otherwise specifically provided for complete all as specified and as directed.

M&L Reinforced cement concrete (Design mix) M-25 (20mm graded stone aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc complete all as specified and as directed.

M&L Reinforced cement concrete (Design mix) M-25 (20mm graded stone aggregate) in columns, pillars, piers, posts and struts complete all as specified and as directed

M&L Reinforced cement concrete (Design mix) M-25 (20mm graded stone aggregate) as in beams, cantilevers, bressummer lintel over 1.5 m span complete all as specified and as directed.

M&L Reinforced cement concrete (Design mix) M-25 (20mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for PCC 1:4:8, type D2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

M&L for brickwork with fly ash bricks (old size), straight or curved on plan, exc 6 m mean radius, built in cement mortar 1:6 with and including demolition of existing brick work built in cement or cement lime mortar of any description complete all as specified and as directed.

Use and waste Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed.

Use and waste Formwork to sides of pillars, posts, struts, piers, columns and stanchions square, rectangular or polygonal complete all as specified and as directed.

Use and waste Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed.

Use and waste Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified.complete all as specified and as directed.

M&L for moorum filling in floors or paving, laid in layers n.exc. 15cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for hard core of gauge not exc. 63 mm, deposited spread and levelled in layers n. exc. 15cm thick, including watering and rammed etc. complete all as specified and as directed.

M&L for rendering 10 mm thick in CM 1:6 on fair faces of brick/concrete surfaces finished even & smooth without using extra cement etc complete all as specified and as directed.

M&L for 15 mm thick rendering in cement mortar 1:4 (using water proofing liquid as per manufacturers instruction) on other than fair faces of brick masonry surfaces or concrete surfaces, finished even and fair without using extra cement complete all as specified and as directed.

Supply only liquid water proofing compound complete, ISI mark all as specified and as directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces as in ceiling finished the surface even & smooth without using extra cement complete all as specified and as directed.

M/L for 40 mm thick Damp proof course to horizontal or vertical surface including necessary formwork, in PCC (1:2:4) type B-0 using 12.5 mm graded crushed stone aggregate mixed with integral water proofing compound conforming to IS-2645 complete all as specified and as directed.

M & L anti termite Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface complete all as specified and as directed.

M & L anti termite Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed.

M & L anti termite Treating the the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.

M & L anti termite Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and as directed.

M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following courses of treatment / specification from bottom to top:- (i) Surface roughening concrete slab by picking, sweeping clean and washing down with water to remove dust etc.and applying cement slurry @3kg/Sqm. (ii) Screed bed or bedding layer of mortar 1:4 in 15 mm thick for laying as in roof slab with mixing of WPC and surface finished fare and smooth without using extra cement. (iii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.25ltr /Sqm conforming to IS:3384-1986. (iv) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/Sqm) shall be less applied over bituminous primer as specified above over a Application of polymeric membrance shall by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction. (v) Applying two coat of bituminous aluminum paint over the APP modified membrance @ 0.11Kg/sqm. Note: Water proofing compound will be measured & paid separately.

M & L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M & L for Mild steel TMT bars 5mm and over upto and including 10mm dia in stirrups spaces and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

S & F in repair stainless steel grating with square frame (grating thickness 1mm and frame thickness 1.5mm) of size 125mm (minimum) with waste hole complete all as specified and as directed.

S&F in repairs, rotational moulded polyethylene water storage tanks colour white (cylindrical vertical with closed top), 500 litres capacity, triple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting complete all as specified and as directed.

Taking up or down 15 mm bore dia GI steel tubing and connections complete all as specified and as directed.

S&F 15mm bore UPVC pipes Sch 40 including fittings, any length with fittings such as socket, elbow, bends, tees, reducer, union, caps plug, nipple etc complete laid in walls/ ceiling or laying in floor trench or fixed to walls complete all as specified and as directed.

Supplying and laying 16 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11, any length with fittings such as socket, elbow, bends, tees, reducer, union, caps plug, nipple etc complete laid in walls/ ceiling or laying in floor trench or fixed to walls complete all as specified and as directed.

Taking up or down 20 mm bore dia GI steel tubing and connections complete all as specified and as directed.

S&F 20mm bore UPVC pipes Sch 40 including fittings, any length with fittings such as socket, elbow, bends, tees, reducer, union, caps plug, nipple etc complete laid in walls/ ceiling or laying in floor trench or fixed to walls complete all as specified and as directed.

S & F in repairs vitreous China, white, squatting pan, Orissa pattern of size 580 X 440 mm with integral foot rests (excluding flusing cistern) including traps & set in lean cement concrete as specified including flush pipe and connecting to trap and flushing cistern complete all as specified and as directed.

S&F in repairs, vitreous china wash down water closet (pedestal pattern) white, including connection to drain (or outgoing pipe) and flushing pipe, anti syphonage pipe, trap set and including white seat cover for pedestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws etc complete all as specified and as directed. Make : Cat No. S1053102 of CERA or equivalent model of makes specified.

S&F Health faucet (ABS Body) suitable for 15 mm dia pipe with 1 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. Make : Cat No. F8030111AB of CERA or equivalent model of makes specified.

S&F in repairs 10 ltr capacity PVC valveless, syphonic action type flushing cistern, low level, white with inlet ball valve and handle including brackets complete all as specified and as directed. Make : Cat No. B1010110 of CERA or equivalent model of makes specified.

S&F in repairs, vitreous china wash basin white of size 550mm x 400mm with brackets including, waste pipe, CP waste coupling 32 mm bore, PVC connection pipe complete all as specified and as directed. Make : Cat No. S2040141 of CERA or equivalent model of makes specified.

S&F in repairs, 15 mm bore pillar taps, cast copper alloy with capstan heads, fancy type, chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed. Make : Cat No. F2014101 of CERA or equivalent model of makes specified.

S&F in repairs, bib tap 15mm dia, with wall flange and aerator screwed down for iron pipe or for brass ferrule complete all as specified and as directed. Make : Cat No. F1015151 of CERA or equivalent model of makes specified.

S & F in repairs, angle valves, 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed. Cat No. F1015201 of CERA or equivalent model of makes specified.

S & F in repairs, PVC connections, 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed.

S&F, Soap dish, chromium plated, fixed to plugs with chromium plated screws complete all as specified & as directed.

S&F in repair bevelled edge looking mirror 5.5mm thick of size 60cmx 45cm mounted on commercial plywood 6 mm thick including PVC beading all round and fixed to wooden plugs with chromium plated screws complete all as specified and as directed.

S&F in repairs wall mixer for mixing hot and cold water and bend for connecting to shower,15 mm bore screwed for iron pipe and fixed complete all as specified and as directed. Make : Cat No. F1015401 of CERA or equivalent model of makes specified.

S&F in repair over head shower rose 125mm size with 200mm long shower arm and wall flange complete all as specified and as directed. Make : Cat No. F7020111AB of CERA or equivalent model of makes specified.

S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide, 60cm long with chromium plated bracket guard and railing complete all as specified and as directed.

S&F in repairs towel rail 60 cm long between flanges complete all as specified and as directed. Make : Cat No. F5015103CH of CERA or equivalent model of makes specified.

S&F in repairs, stainless steel sink with drain board made of 1mm thick sheet for kitchen with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 350mm x 200 mm including CP coupling complete all as specified and as directed. Make : Cat No. SBSD 05 (RR) of JAYNA or equivalent model of makes specified.

Taking down chowkhats or frames with shutter (without taking out shutter from the frame), area n.exc 1.5 sqm each all as specified and as directed.

Taking down chowkhats or frames with shutter (without taking out shutter from the frame), area exc 1.5 sqm but not exc 4 sqm each all as specified and as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges 4 nos per leaf of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges 4 nos per leaf of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S&F 35 mm thick, second class hard wood, glazed and and skeleton shutters, factory made, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); supplied and fitted to chowkats all as specified and as directed.

S & F powder coated aluminum windows, three track, made out of aluminium sections including all necessary fittings, 5mm thick sheet glass, rubber/ neoprene beading, locking arrangements all as specified and as directed and comprising of following sections :- (a) Window frame: (i) Bottom-Section 20671 (Wt not less than 0.699 Kg/m) (ii) Top & Side - 20672 (Wt not less than 0.594 Kg/m) (b) Shutter: (i) Vertical (end)- 20669 (Wt not less than 0.548 Kg/m) (ii) Vertical (lock) - 20689 (Wt not less than 0.481 Kg/m) (iii) Bottom - 20718 (Wt not less than 0.263 Kg/m) (iv) Top - 20668 (Wt not less than 0.377 Kg/m) Note : Shade shall be as approved by Engineer-in-Charge.

S&F 100 mm long SS butt hinges, medium weight, cold rolled and fixed with screws/welded complete all as specified and as directed.

S&F 150 mm size extruded aluminium alloy handles fabricated type anodised and fixed complete all as specified and as directed.

S&F 125 mm size extruded aluminium alloy handles fabricated type anodised and fixed complete all as specified and as directed.

S&F 150 mm size aluminium anodized barrel tower bolts of extruted section and fixed complete all as specified and as directed.

S&F 200 mm size aluminium anodized barrel tower bolts of extruted section and fixed complete all as specified and as directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F 200mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

M&L for stainless steel wire cloth 0.36 nominal dia of wire and average width of aperture 1.4mm and fixed with stanless steel staple to wooden/steel frames complete all as specified and as directed.

S&F in repairs 20mm dia stainless steel curtain rod with brackets and finials at both ends as per site requirement including taking down old curtain rods with accessories complete all as specified and as directed. Note: The cost of brackets & knobs shall deemed to be included in the quoted rate.

S&F in repairs, 18 mm thick WPC Board (Wood Polymer Composite), termite proof, waterproof & screwable & nailable as in fabrication of storage System, cupboards in rooms/kitchen i/c Drawers, shelves, etc. laminated one side with decorative choice lamination and other side balancing white lamination, with teak wood lipping on the edges of the shutters and the box etc. including necessary fixing arrangement on walls with fasteners, complete all as specified and as directed.

S&F 100mm size Stainless steel handles extruded section, complete all as specified and as directed.

S&F continous (Piano) hinges, brass bright finish width of flaps 30mm when open complete all as specified and as directed.

S&F in repair magnetic catcher, Double strip (horizontal type), in cupboard/ward robe shutters including fixing with necessary Stainless Steel screws etc. complete all as specified and as directed.

Dismantling of mild steel iron works of any description not otherwise provided for etc all as specified and as directed.

M & L for Framed work such as grills, gratings, etc., framed guard bars and similar work with ends of bars shoulders and / or riveted, or forged into spikes; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and as directed.

M & L for mild steel Bands, straps, supports or stays for rainwater, ventilating pipes including bolts of required size, hooks (stay) for gates, hook and pintle hinges large hasps and staples chains hand made sliding bolts clamps hold fasts wall tiles hooks for hanging fans, plain, angle cleats for securing purlins to wood truses or fats knee piece insert two way and three way straps plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

S&F ventilator of size 600 x 900 mm made out of aluminium frame/ sections (Wt not less than 0.55 Kg/m) including all necessary fittings, rubber/ beading including 3 mm thick frosted glass louvers, wiremesh etc and arrangements for fixing exhaust fan complete all as specified and as directed. Note : Shade shall be as approved by Engineer-in-Charge.

Demolition of kota, granite, cudappah stone slabs and interlocking tiles of any description or thickness in floor apron etc laid, bedded and pointed in any mortar.

M&L for machine cut cudappah stone slab 20-25mm thick for cooking platform, wash basin, sink etc including cutting chases in wall and fixing the slab in cement mortar including rubbing and polishing complete all as specified and as directed.

M & L for 18-20mm thick prepolished Granite stone slab of approved shade and colour as in table top, top of WHB, kitchen slab/platform, gate pillars, cills etc or on vertical surfaces including vertical projections, including full round mouldings the edges laid over and over and including screed bed 15mm thick in cement mortar 1:4 jointing, pointing in white cement 1:2 using marble dust with admixture of pigments to match the shade of granite and rubbing polishing to achieve mirror finish complete all as specified & directed. Note:- Colour/shade to be decided by Engineer-in-Charge.

M&L for machine cut Kota stone flooring 18 to 22 mm thick (size of kota stone slab 22"x22") laid over and including 20 mm thick bedding layer of cement mortar 1:6, jointed with grey cement slurry mixed with pigments to match the shade of slab including cutting, rubbing and mirror polishing including removing dust complete all as specified and as directed.

All as per item No 100 here in before but 15-18 mm thick as in risers to steps and skirting laid over and including backing coat of 10mm thick in cement mortar 1:3 all as specified and as directed. Note : Risers provided to steps shall be in one piece.

Dismantling floor, hearth or wall tiling including cement morter bedding ( but not backing ), removing serviceable tiles to store and rubbish off the premises.

M & L for Non-skid coloured Ceramic tiles mat finish 7 to 8 mm thick ( square /Rectangular) area of each tile exceeding 0.18 sqm but not exc 0.38 sqm (600x600mm) in floors etc set and jointed in neat cement slurry and pointed in white cement to match with tile laid over and including screed bed or bedding layer of 15 mm thick in CM (1:6), complete all as specified and directed. Note :- Colour and shade shall be approved by Engr-in-Charge.

Ditto all as per item No 103 above but as in skirting set and jointed in neat cement and pointed in white or coloured cement to match including 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7-8mm thick (square or rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 etc complete all as specified & as directed. Note: Color and shade shall be as approved by Engineer-in-charge

M&L for glazed coloured ceramic tiles in vertical surfaces as dado of size 450x300x6-7mm, thick set and jointed in neat cement and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:3 on other than fair faces of brick work etc complete all as specified & as directed. Note: Color, size and shade shall be as approved by Engineer-in-charge

M&L for 75mm thick plain cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base of floors and pavings complete all as specified and as directed.

Supply and fixing laminated Gypsum tile board 8 mm thick with textured white colour PVC film on the face side and metalized polyster (MPL) film on rear side in ceiling as per manufacturers of size 595X595 mm in true hotizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections (galvanized @120grams/Sqm both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24X38 mm made from 0.30 mm thick (minimum)sheet, spaced at 1200 mm center to center and cross "T" of size 24X25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center form a grid of 1200X600 mm and secondary cross "T" of length 600 mm and size 24X25 mm of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200X600 mm panel to form grids of 600X600 mm and wall angle of size 24X24X0.3 mm and laying false ceiling tiles of approved texture in the grid including,required cutting/marking,opening for services like diffusers, grills, light, fittings,fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27X37X25X1.6 mm fixed to ceiling with 12.5 mm dia and 50mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85X30X0.8 mm spaced at 1200 mm center te center along main T, bottom exposed width of all T-section shall be pre-painted with polyester paint, complete all as specified and directed.

S&F laminated Gypsum tile board 8mm thick with textured white colour PVC film on the face side and metalized polyster (MPL) film on rear side in ceiling as per manufacturers instructions of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @ 120grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, including dismantling of existing false ceiling work of any description complete all as specified and as directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness in roof coverings complete all as specified and directed.

S&F prepainted galvalume aluminium zinc coated galvanised iron based corrugated steel sheets 0.5 mm thick of any colour, AZ150, having tensile strength 550 MPA as in roof covering or ridges with side lap and end laps, hips and straight flashing fixed with self taping screws (length & girth as fixed) complete all as specified and as directed. Note:- Colour & Pattern to be approved by Engineer-in-Charge.

S&F pre-painted galvalume aluminium zinc coated galvanised Iron based Plain steel sheets, 0.5mm thick of any colour, AZ150, with side lap and end lap having tensile strength 550 MPA as in ridges, hips, valley gutters, drip and straight flashing fixed with self taping screws (length & girth as fixed) complete all as specified and as directed.

M&L for preparation of new plastered internal surfaces of wall and applying two coat of acrylic distemper of required shade and colour complete including one coat of primer as per manufacturer's specifications in any colour complete all as specified and directed.

M&L for Complete removal of existing treatment on walls including cornices by scrapping with steel scrappers or any other means including filling depressions of scrapped surfaces and making smooth surface with one coat of average 1.5 mm to 2 mm thick wall care putty and applying two coat of acrylic distemper (white or tinted) over a coat of primer complete all as specified and as directed.

M&L for preparation of new plastered surfaces or previously untreated surface of wall and applying two coats of cement base paint over one coat of alkali resistant primer complete all as specified and as directed.

M&L for preparation of old plastered or unplastered surfaces of walls including cornices and applying two coat of cement base paint (white or tinted) complete all as directed and as specified.

Preparation of new plastered surfaces of ceiling and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and directed.

M&L for preparation of new steel surface of any description over 10cm in width or girth and applying two coats of synthetic enamel paint of any shade over a coat of red oxide primer complete all as specified and directed.

S&F in repair for 110 mm bore PVC (SWR) pipes single socketed with rubber ring joints, laid in trenches or in floors complete all as specified & directed.

S&F in repair for 110 mm bore PVC (SWR) pipes single socketed with rubber ring joints, fixed to walls, complete all as specified & directed.

S&F in repair for 110 mm bore PVC (SWR) junction double, (double Y) equal or unequal, with oval access door, complete all as specified & directed.

S&F in repair for 110 mm bore PVC (SWR), bend any radius, with oval access door complete all as specified & directed.

S&F in repair for 110 mm bore PVC (SWR), bend any radius, complete all as specified & directed.

S&F in repair for 75 mm bore PVC (SWR) pipes single socketed with rubber ring joints, laid in trenches or in floors complete all as specified & directed.

S&F in repair for 75 mm bore PVC (SWR) pipes single socketed with rubber ring joints, fixed to walls, complete all as specified & directed.

S&F in repair for 75 mm bore PVC (SWR) junction single, (single Y) equal or unequal, with oval access door, complete all as specified & directed.

S&F in repair for 75 mm bore PVC (SWR), bend any radius, with oval access door complete all as specified & directed.

S&F in repair for 75 mm bore PVC (SWR), bend any radius, complete all as specified & directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rail and guides for sliding doors; fixed with angle cleats or other connecting plates grade Fe-410- W(Gde- E-250) quality- A complete all as specified and as directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. grade Fe-410- W(Gde- E-250) quality- A complete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,in hard/dense soil complete all as specified and as directed.

M&L for providing Cement concrete in foundations, filling and mass concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) complete all as specified and as directed.

S&F prepainted galvalume aluminium zinc coated galvanised iron based corrugated steel sheets (Mangalore pattern design) 0.5 mm thick of any colour, AZ150, having tensile strength 550 MPA as in roof covering or ridges with side lap and end laps, hips and straight flashing fixed with self taping screws (length & girth as fixed) complete all as specified and as directed. Note:- Colour & Pattern to be approved by Engineer-in-Charge.

M&L for PCC 1:2:4 type B-0 (20 mm graded stone aggregate) as in copings, complete all as specified and directed

M&L for 80mm thick, factory made, chamfered edge, cement concrete interlocking paver blocks (glossy/ rubber matt finish) of M-40 grade with approved colour, design & pattern of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 25mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as required size and pattern, finishing and sweeping extra sand; etc complete all as specified and as directed. Note : Size, shape, pattern and shade shall be as approved by Engineer-in-Charge.

Supply and fix 6mm thick ACP Wall Panelling with aluminium composite panel cladding in approved shades made out of 6mm thick aluminium composite panel material consisting of 5mm thick FR grade mineral core (having 2 hours fire resistance in accordance to ASTM E119-12 and EN13501-1 Class B,) sandwiched between two Aluminium sheets (each 0.5mm thick of AA3105 grade) fixed over aluminium frame work as per manufacturer's directions complete as directed.

Supply and Fix Refrigerator min 300 Ltrs capacity, Single phase, Inverter Compressor, frost free cooling with auto defrost, double door complete with Non CFC gas, latest energy efficient 5 star rating model complete all as specified and as directed by Engr in Charge.

Supply, installing, connecting, testing and commissioning storage type stainless steel body water cooler 80 Litres capacity and cooling capacity 40 Litres per Hour, single phase 230 Volts, based on eco friendly gas and latest energy efficient model including all connections with control valves tapping from nearest water point and extending drain out pipe to the nearest drain system and necessary power cable and plug top up to nearest electrical point as per site requirement complete all as specified and as directed by Engr In Charge.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, bell push, holders, ceiling roses, pendants, regulators, sockets etc but excluding DBs, light fittings etc and making good disturbed surfaces of walls, floors etc. and matching with existing surface all as specified and as directed.

M&L for point wiring complete on surface of wall (open) type with two runs of 1.5 sqmm for phase and neutral, single core, multistranded copper conductor cable of 1100 Volts grade,conforming to IS-694 1990, PVC insulated and unsheathed , FRLS cable drawn through and including PVC casing and caping (ISI marked) and its accessories such as Tee, elbow, jointer, elbow corner etc. fixed on surface of walls, coloumns/ beams alongwith 1.5 Sqmm copper conductor cable (multistranded) PVC insulated and unsheathed FRLS cable as earth wire connected to common earth dolly at one end and metalic bodies of luminaire/ fan at other end including PVC folding boards/bakelite sheets for mounting switches, sockets, fan Regulators, accessories etc as specified and as directed for one light point or one fan point controlled by one, one way switch NOTES: (a) Proper colour coding shall be adopted for wiring (for phase-RED,YELLOW, BLUE for Earth-Green and Neutral-Black) (b) Wiring shall be done as per complaints received from user only on reqired basis it is not necessary to do whole wiring of any whole bldg. (c) All points shall be earthed up to fixtures i.e holders, tube lights, all lights, ceiling lights, bulkhead lights, bldg security lights etc.

All as per serial item No. 140 here in before but one 5 Amp 3 pin socket outlet point on same board with other switches including earth wire.

All as per serial item No. 140 here in before but on independent board.

All as per serial item No. 140 here in before but for one bell/buzzer point controlled by one push button on the same board with other switches or independent.

All as per serial item No. 140 herein before but with 2.5 Sqmm, PVC copper stranded cable FRLS type for phase, Neutral and earth for one 15 Amp, 6 pin socket on independent board.

S&F switch piano, flush button, 6 Amp, single pole, one way, 230 volts, white finish, all as specified & as directed.

S&F switch socket combination, flush type, 5 pin, 6 Amp, multipurpose, 230 volts, single pole, one way, suitable for 3 pin/2pin 5 Amp plug top white/ivory finish all as specified & as directed.

S&F switch socket combination, multipurpose, flush type, 2 in 1 type (6 pin ) 6/16 Amps, 230V, AC. all as specified & as directed.

S&F lamp holder, angle/ batten type, PVC/Polycarbonate type with back plate, suitable for batten fittings all as specified & as directed.

S&F ceiling rose, surface PVC 50mm dia, 3 terminals including PVC mounting block white/ivory finish all as specified & as directed.

S&F bell push, flush type, 6 Amp, single pole, 230 volts, white finish all as specified & as directed.

S&F fan regulator, step type, electronic on existing phenolic laminated sheet, 5 step, socket type, 230 volts, 250 watts, suitable for ceiling fan 1200/1400mm sweep all as specified & as directed.

S&F bell, AC, 230 volts, single phase complete all as specified and as directed.

S&F square profile LED lighting fixture with extruded polycorbonate,environmental friendly,energy efficient ready to use pack LED Tube light fitting 20 Watt with LED light source 6500k with uniform light output,with all accessories including its connection complete with all as specified and directed by Engineer-in-charge.Make:HAVELLS LED PRIDE ESSENTIAL Cat No LHEXAWP71N1W020 or equivalent as approved by GE.

M&L for sub main wiring with 2 runs of 2.5 sqmm, single core, PVC insulated & unsheathed FRLS cable conforming to IS-694, 1100 volts with copper conductor, multi stranded drawn in and including suitable size heavy grade casing caping (ISI marked) with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 2.5 sqmm single core PVC insulated & unsheathed FRLS copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old submain wiring and any type of conduit complete all as specified and as directed. NOTES: (a) Proper colour coding shall adopted for wiring (for phase-RED, YELLOW, BLUE for Earth- Green and Neutral-Black) (b) Three runs of 2.5 sq.mm cable and one run of PVC casing & caping shall be measured as one unit.

S&F in repairs, MCB SP, AC 240 V, 6 to 32 Amps, 10 KA capacity ,'C' series, making connection with suitable size of copper lugs etc complete all as specified and as directed.

S&F in repairs, MCB SPN, AC 240 V, 6 to 32 Amps, 10 KA capacity ,'c' series, making connection with suitable size of copper lugs etc complete all as specified and as directed.

S&F in repairs, MCB DB, double door type (when MCBs are to be used), single pole and neutral, 240 volts, 4 way, protection class IP-42, suitable for fixing MCBs, Isolators etc, confirming as per IEC 61439-3, suitable for flush mounting and surface mounting, with 200 Amps rated copper busbar, with Neutral bar, Earthbar and cable alley for cable managment, fully shrouded, Neutral bars, prefittes masking sheet complete all as specified and as directed.

Supply and fix 200mm sweep Exhaust fan PVC body with louvers shutter 230 volt 50 HZ 1330 RPM, min air delivery 750 CHM, including three core copper conductor flexible cord of 0.5 sqmm cross sectional area of required length from ceiling rose to exhaust fan all as specified and as directed.

M&L for making hole in brick / block / stone masonry wall for fixing of Exhaust fan of 200 mm sweep and making good the disturbed surfaces with cement morter 1:4 and applying two coats of acrylic distemper of same colour alongwith wall care putty to match the existing surface complete all as specified and directed by Engr-in-Charge

CHAUDHARY AND ASSOCIATES (BID ID -3447061)

JANARDHANANDSONS (BID ID -3448043)

M/S H.N.ENTERPRISES (BID ID -3448399)