1) Construction of Office of ADSTE/PKU at Panskura. 2) Panskura:- Construction of Type IV Quarter of ASTE at Panskura under the jurisdiction of Sr.DEN/EAST/KGP.

A-Execution of works covered under Schedule-A. 8938684.75 Below/P

B-Execution of works covered under Schedule-B. 5209155.00 Below/P

C -Execution of works covered under Schedule-C. 18900.00 Below/P

Preparation of Design & drawaing for station building & other buildings (Should be as per latest circular). Notes: (i) The contractor will carryout detailed survey and prepare GAD and get it approved from Railway. (ii) The rates are inclusive of visits to site if required. The site of the work falls under the jurisdiction of DEN/West/KGP. (iii) The above quantities are approximate. The Railway reserves the right to increase/decrease the same. Additional special conditions of contract: i) The Agency will get the design checked from Railway. For this purpose Agency will ensure the presence 3 of his representative in the offices of Railway authorities whenever required. Nothing extra will be payable for the above and the rate is inclusive of above. ii) After drawing got approved by Railway, the Agency will have to submit three copies of initial design calculations with 3 ferro copies of drawings to Railway for record. Design calculation should be clearly written and bound in book form. iii) On clearance of design criteria from Railway for any modification, agency will carry out detailed design again as required without any loss of time after clearance of design parameters. He will also be prompt in clarifying the observations/doubts of the Railways. No extra payment shall be made for the any alterations. iv) Design and drawing after approval shall be property of S. E. Railway who shall have exclusive right to use or reuse it elsewhere. The consultant shall have no claim whatsoever in this regards. v) Based on the design note approved by Rly, the Agency will prepare final general arrangement drawing. Mode of payment: i) Visit to site and collection of field data from site, and detailed design of and preparation of GAD, submission to Railway 3 sets of GAD (Ferro copy), design calculation 3 booklet = 20%. ii) After acceptance of Railway = 50%. iii) Final submission of drawing approved in item (ii) above in reproducing tracing films 3 copies and soft copy on CD, 3 sets of ferro prints for each drawings, final design calculation booklet. Payment will be made after signature of Railway authorities in final drawing =30%

Item Breakup - A-Execution of works covered under Schedule-A.

prepare the surface even and smooth complete. 13.37S INTERIOR FINISHING 13.37 White washing with lime to give an even shade : 43 13.37.1 New work (three or more coats) Sqm 50 39.05 1952.5 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 13.41 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : 13.41.1 New work (two or more coats) over and Sqm 200 185.65 37130 including water thinnable priming coat with 44 cement primer having VOC content less than 50 gram/litre 13.44S EXTERIOR FINISHING Finishing walls with water proofing cement paint 13.44 of required shade : 13.44.1 New work (Two or more coats applied @ 3.84 Sqm 200 116.9 23380 45 kg/10 sqm) Finishing walls with 100% Premium acrylic emulsion paint (Company Depot Tinted) having VOC less than 50 gm/litre and UV resistance as 13.48A per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives. 13.48A.1 New work (Two or more coats applied @ 1.43 Sqm 600 181.25 108750 46 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. Painting with synthetic enamel paint of 13.61 approved brand and manufacture to give an even shade : 47 13.61.1 Two or more coats on new work Sqm 600 155.9 93540 15.0 DISMANTLING AND DEMOLISHING 15.1S General 15.3 Demolishing R.C.C. work manually/ by cum 15 3551.25 53268.75 mechanical means including stacking of steel 48 bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. Demolishing brick work manually/ by mechanical means including stacking of 15.7 serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. 49 15.7.4 In cement mortar cum 15 2060.2 30903 17.0 SANITARY INSTALLATIONS 17.1S General Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with 17.2 manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : 17.2.1 W.C. pan with ISI marked white solid plastic Each 4 6515.55 26062.2 50 seat and lid KHARAGPUR DIVISION-ENGG/SOUTH EASTERN RLY Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. 17.5 brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : 17.5.1 Single half stall urinal with 5 litre P.V.C. Each 3 12071.75 36215.25 51 automatic flushing cistern Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm 17.7 C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 17.7.1 White Vitreous China Wash basin size 630x450 Each 5 2648.85 13244.25 52 mm with a pair of 15 mm C.P. brass pillar taps Providing and fixing P.V.C. waste pipe for sink 17.28 or wash basin including P.V.C. waste fittings complete. 17.28.2 Flexible pipe 53 17.28.2.1 32 mm dia Each 4 119.55 478.2 17.35 Providing and fixing soil, waste and vent pipes : 17.35.1 100 mm dia 54 17.35.1.1 Sand cast iron S&S pipe as per IS: 1729 Metre 12 1151.9 13822.8 18.0 WATER SUPPLY 18.4S PP-R PIPES Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & 18.4 brass threaded polypropylene random fittings and fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineer-in-Charge. ( Internal Exposed on walls ) 55 18.4.2 PN - 16 Pipe, 25mm OD (SDR-7.4) Metre 29 318.35 9232.15 56 18.4.3 PN - 16 Pipe, 32mm OD (SDR-7.4) Metre 16 362.9 5806.4 57 18.4.4 PN - 16 Pipe, 40mm OD (SDR-7.4) Metre 16 545.75 8732 Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801 UV stabilized & anti - microbial fusion welded, having thermal stability for hot & 18.6 cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, including trenching, refilling & testing of joints complete as per direction of Engineer-in- Charge. External work 58 18.6.4 PN - 16 Pipe, 40 mm OD (SDR-7.4) Metre 13 415.1 5396.3 59 18.6.5 PN - 10 Pipe, 50 mm OD (SDR-11) Metre 16 450.95 7215.2 18.6A Providing and fixing PPR Unions 60 18.6A.1 PPR Union 20mm Each 7 315.5 2208.5 61 18.6A.4 PPR Union 40mm Each 7 543.1 3801.7 18.7S C.P.V.C. PIPES Providing and fixing G.I. pipes complete with 18.12 G.I. fittings including trenching and refilling etc. External work 62 18.12.6 50 mm dia nominal bore Metre 60 762.15 45729 63 18.12.7 65 mm dia nominal bore Metre 60 896.6 53796 18.15S BRASS FITTINGS KHARAGPUR DIVISION-ENGG/SOUTH EASTERN RLY Providing and fixing brass stop cock of 18.16 approved quality : 64 18.16.1 15 mm nominal bore Each 2 353.25 706.5 C.I. SLUICE VALVES/ FIRE HYDRANTS & 18.31S FIXTURES 18.48 Providing and placing on terrace (at all floor Per 2000 11 22000 levels) polyethylene water storage tank, IS : Litre 12701 marked, with cover and suitable locking 65 arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 18.49S C.P. BRASS FITTINGS Providing and fixing C.P. brass bib cock of 18.49 approved quality conforming to IS:8931 : 66 18.49.1 15 mm nominal bore Each 11 506.8 5574.8 18.59S AIR VALVE & WATER METER (BULK TYPE) Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy 18.62 coated aluminium rod with L.P./ H.P.H.D. plastic ball. 18.62.4 40 mm nominal bore, 206mm long, weighing Each 3 737.2 2211.6 67 not less than 690 gms 20.0 PILE WORK 20.1S General Providing, driving with hydraulic piling rigs with power units and installing driven cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry safe working load not less than 20.1 specified, excluding the cost of steel reinforcement but including the cost of shoe and the length of pile to be embedded in the pile cap etc. all complete. (Length of pile for payment shall be measured from top of shoe to the bottom of pile cap) : 68 20.1.1 400 mm dia piles Metre 500 2767 1383500 Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than 20.3 specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) : 69 20.3.3 450 mm dia piles Metre 300 4232.75 1269825 21.0 ALUMINIUM WORK 21.1S General KHARAGPUR DIVISION-ENGG/SOUTH EASTERN RLY Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with 21.1 required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : 21.1.1 For fixed portion 21.1.1.2 Powder coated aluminium (minimum thickness Kg 49 530.9 26014.1 70 of powder coating 50 micron) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings 21.1.2 wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) 21.1.2.2 Powder coated aluminium (minimum thickness Kg 55 634.45 34894.75 71 of powder coating 50 micron) Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. 21.3 complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 21.3.1 With float glass panes of 4.0 mm thickness Sqm 12 1176.8 14121.6 72 (weight not less than 10kg/sqm) Total 7772769.35

Item Breakup - B-Execution of works covered under Schedule-B.