SPECIAL REPAIR TO BLDG NO.41 (08 QTRS) IN DOMESTIC AREA AND PROVN OF PARKING SHED AT BLDG NO. 29 (JCOS MD ACCN) AT OD AVADI INCLUDING PROVN OF 07 X GEYSERS IN DGQA GUEST HOUSE UNDER GE AVADII

Amount

Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) complete all as specified and directed .

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed

Removing vegetation/shrub/tree growth including roots from buildings at any height and any location without damaging the structure, applying Glyphosate-based pesticide or equivalent (10 ml in 1 litre of water) on roots using spray gun to prevent regrowth, taking down loose/damaged cement plaster not exceeding 0.50 sqm per location caused due to root penetration, and making good the surface with 20mm thick cement plaster in CM 1:4 mixed with waterproofing compound @ 3% by weight of cement, finished to match the existing surface including all necessary scaffolding, tools and plants, safety measures, and disposal of debris complete all as specified and directed.

Demolition of cement conctrete (un-reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed

M & L for 40mm thick PCC 1:2:4 type B1 (using 20mm graded stone aggregate) (Padding concrete) with water proofing compound and finished even and fair complete all as specified and directed Note : water proofing compound will be measured and paid separately.

M & L for screed bed of mortar 15 mm thick in cement mortar 1:4 for laying APP membrane and including mixing water proofing compound as per manufactureres instructions complete all as specified and directed Note :- Water proofing compound shall be measured and paid for seperately under appropriate item of Sch "A' as supply only.

Supply only Liquid water proofing compound complete all as specified and directed

M & L for brushing neat cement slurry with 3.0 kg of cement per square metre complete all as specified and directed by Engr-in- Charge.

M&L in repairs for preparing RCC roof surfaces by removing existing damaged waterproofing treatment completely, cleaning the surface with wire brush, washing with water to remove all loose particles and foreign materials, brushing neat cement slurry using 3.0 kg of cement per sqm, applying one coat of bituminous primer @ 200 gms per sqm, and then laying 3mm thick APP (Atactic Polypropylene) modified bituminous membrane weighing not less than 3.50 kg/sqm, reinforced with polyester mat not less than 160 gms/sqm, laid by torch application method with overlaps of 75 mm on longitudinal joints and 100 mm on transverse joints, all junctions, angles and changes in plane sealed with care including provision of fillet using CM 1:3 mixed with waterproofing chemical as per manufacturer's instructions, properly cured before membrane application, and finishing with aluminium paint @ 100 gms/sqm over horizontal and vertical surfaces, complete all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing and rubbish off the primises complete all as specified and directed

M & L for coloured Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm/ 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles and including rendering 10 mm thick in CM (1:4) on fair faces of brick work complete all as specified and directed

M & L for Non-Skid coloured ceramic tiles 7 to 8 mm thick (Square / Rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15mm thick screed bed or bedding layer in cement mortar (1:6) for laying floor finishes like tiles complete all as specified and directed

M & L for Joint free Non-Skid coloured ceramic tiles 7 to 8 mm thick (Square / Rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15mm thick screed bed or bedding layer in cement mortar (1:6) for laying floor finishes like tiles complete all as specified and directed

M & L for Joint free Non-Skid coloured ceramic tiles 7 to 8 mm thick (Square / Rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in . set and jointed in neat cement slurry and pointed in white or coloured cement to match and rendering 10 mm thick in CM (1:4) on fair faces of brick work complete all as specified and directed

M & L for 40mm thick PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) cement concrete in sub base complete all as specified and directed

Demolition of precast concrete block walling and similar items i.e. ashlar facing dressing stone work, precast concrete articles etc of any description and in any position built in cement mortar including all quoins, arches and pillars etc. complete all as specified and directed

M & L for precast cement concrete block masonry with solid blocks exc 10 cm in width and set and jointed in C M 1:6 having ratio of PCC 1:3:6 type C1 (using 20mm graded stone aggregate as directed complete all as specified and directed

S & F in repairs of stainless steel kitchen plate rack size 750 x 600 x 250 mm & 0.63 mm thickness of grade AISI 304 incl suitable arrangements for hanging to wall complete all as specified and directed

Dismantling of structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed

M & L for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed

M&L for preparation of new or previously untreated steel surfaces and applying two coats of synthetic enamel paint over a coat of primer red oxide, zinc chrome complete all as specified and directed

Taking down of chowkhats / frames n exc 1.50 sqm each without taking off shutter each complete all as specified and directed

Taking down of chowkhats / frames exc 1.50 Sqm but n exc 4.0 sqm each without taking off shutter each complete all as specified and directed

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of complete all as specified and directed

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass / stainless steel screws complete all as specified and directed.

S & F of Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction complete all as specified and directed

S & F of Anodised aluminium window powder coating of any colour (Thickness or powder coating not less than 50 micron). and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 nos.) suitable handle (1 no.) complete all as specified and directed.

S & F of 5.5mm thick Sheet glass, ordinary quality and and glazing with oil putty in square n exc 0.5 sq. m in each pane and sheet glass is ground or obscured or frosted, on one side complete all as specified and directed.

S & F of 4mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed

S & F of stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed

S & F of aluminium (extruded section) body door closer hydraulically regulated designation No 3, universal type,suitable for door shutters of 851 to 1000mm in width and weight between 61 to 80 kg complete all as specified and directed

Taking down cement plaster of any description from brick wall or concrete surfaces including racking out joints and hacking for key, scrubbing down with water etc complete all as specified and directed

M & L for 15 mm thick plaster in CM (1:6) on brick work / RCC concrete surfaces of wall and finish the surface even and smooth without using extra cement complete all as specified and directed

M & L for 5 mm thick plaster in CM (1:3) on brick work / RCC concrete surfaces of ceilings complete all as specified and directed

M & L for rendering 15 mm thick in CM 1:4 on concrete / fair surfaces of block masonary and including mixing water proofing compound as per manufactureres instructions and finished even and smooth without using extra cement complete all as specified and directed. Note :- WPC shall be measured and paid for seperately.

M & L for preparation of newly plastered ceiling surfaces and applied three coats of white wash complete all as specified and directed.

M & L for preparation of old plastered ceiling surfaces and applied one coats of white wash complete all as specified and directed

M & L for preparation of newly plastered wall surfaces and Providing and applying 3mm thick wall care putty on wall to prepare the surface even and smooth, including priming plastered and other surfaces with alkali resistant priming paint and Material and labour for Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work complete all as specified and directed

M & L for preparation of newly plastered wall surfaces and Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed

Complete removal of existing treatment on wall (any number of layers) by scarping with steel scrapers or any other mean and Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed

Complete removal of existing treatment on wall (any number of layers) by scarping with steel scrapers or any other mean including filling depressions of scrapped surface with putty and including priming plastered and other surfaces with alkali resistant priming paint and Material and labour for Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work complete all as specified and directed

Demoltion of Cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M & L for cement concrete type C-2, 1:3:6 (40mm graded stone aggregate), 75mm thick. as in plinth protection finished even and smooth without using extra cement including expansion joints complete all as specified and directed.

Taking up or down steel tubing / CPVC Pipes and connection including cleaning for refixing or removed to store for16 mm bore dia

All as per item no 44.00 here in before but for 20 mm bore dia.

All as per item no 44.00 here in before but for 25 mm bore dia.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified & directed for 16 mm outer dia

All as per item no 47.00 here in before but for 20 mm outer dia

All as per item no 47.00 here in before but for 25 mm outer dia

Cutting chases, pinning in making good to facing on brick walls where required and pointing in cement mortar (1:3) to ends for concealed water tubing and making good ,cutting n, exc. 10cm girth complete all as specified and directed.

S & F in repairs Vitreous China wash down water closet pan (Pedestal pattern) white, including trap and connection to drain and flushing pipe (excluding flushing cistern) including seat cover with recessed bottom and mild steel chromium plated or aluminium hinging devices for pedstal pan and Flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern complete all as specified and directed.

S & F in repair vitreous China squatting pan, 'Orissa patteren, size 580 x 440 mm white, with integral footrests including provision of lime concrete bedding (excluding flushing cisteren and flush pipe) and supply and fixing of Flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern complete all as specified and directed.

S & F in repairs Vitreous China Wash basins, white, flat back, size 630x450mm, including cutting for and pinning in ends of brackets or erecting stand but inclusive of supply and fixing of waste couplings and waste pipe complete all as specified and directed.

S & F in repairs 10 litre capacity PVC low level flushing cistern with all accessories complete fixed with WC including syphone pipe, PVC flushing pipe of size complete all as specified and directed.

S & F in repair PVC connection 15mm size PTMT nuts of length 450 mm complete all as specified and directed

S & F in repair 15 mm bore fancy type angular valve cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions. Make : Hindware F330043CP and equivalent as listed in Particular Specification here in after.

S & F in repair of two way bib cock chromium plated fancy type 15 mm bore with wall flange complete all as specified and directed. Make : Hindware F740004CP and equivalent as listed in Particular Specification here in after.

S & F in repair fancy type CP pillar tap with capstan heads, spindles and washer plates cofirm to IS 1795 having mark 'Cold' or 'Hot' and weight not less than 0.65 Kg complete all as specified and directed.

S & F in repair 15 mm bore fancy type bib taps long body cast copper alloy chromium plated, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

S & F in repairs to health faucet with 1200 mm long flexible 32mm dia outlet pipe and having 184.5mm length of handle with wall hook complete all as specified and directed. Make : Hindware F160023CP and equivalent as listed in Particular Specification here in after.

S & F in repairs 15 mm bore overhead shower Brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified & directed.

S & F in repair CP Soap dish of having size 160x 160x90mm, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S & F in repairs Tubular towel rail, 20mm dia, D type, 60cm long between flanges brass chromium plated complete all as specified and directed.

S & F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long below WHB mirror complete all as specified and directed.

S & F in repairs SS cockroach trap / nahani trap having size of 150mm x 150mm in sqaure shape SS 304 Grade glossy finish complete all as specified and directed.

S & F in repairs SS floor drain having dia of 125mm in circular shape SS 304 Grade glossy finish with or without hole for waste pipe complete all as specified and directed.

S & F in repairs PVC Waste pipe / outlet connector pipe 32mm dia / 40mm and length 1150mm and corrugated profile for fixing in WHB / Sink complete all as specified and directed.

S & F of 25 mm bore ball brass valves,high pressure,with polythene float and flunut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S & F in repairs 25 mm bore dia gun-metal,globe or gate valves,with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Dismantling water tanks and removing to store Exc 500 litre & n exc 1000 litre amd Supply and fixing of 1000 litre capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

Taking down of chowkhats / frames n exc 1.50 sqm each without taking off shutter each complete all as specified and directed.

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm single piece extruded PVC profiles reinforced with 19 x 19mm MS square tube provided with EPDM rubber gasket weather seal through out the frame and the profile mitre cut at two corners and joined by inserting 2 nos 150mm long brackets of 15 x 15mm MS square tube inside 19 x 19mm MS square tube suitably screwed complete all as specified.

Supply & fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes of size 15 x 15mm for top and bottom rails and 19 x 19mm for stiles, MS frame covered with 5mm thick single piece extruded PVC profile 'C' channel having a 5mm thick PVC sheet strip of 20mm width struck inside with solvent cement, forming stiles, and 5mm thick single piece extruded PVC profile for top rail, lock rail & bottom rail on either side, and 10mm (5mm x 2) thick, 20mm wide cross PVC sheet as gap insert for top rail & bottom rail; panelling of 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with PVC sheet beading, and joined together with solvent cement adhesive etc all as per manufacturer's instructions and drawings as shown in SSR Part-I 2009 complete all as specified and directed.

S & F of aluminium anodised 200 mm barrel tower bolts of extruded section complete all as specified and directed.

S & F of 150mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F of 100 mm butt hinges extruded aluminium alloy with galvanized mild steel hinges pin anodised type `C'-22 complete all as specified and directed.

S & F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement morter to dwarft wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S & F of 40mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S & F of stainless steel decorative curtain rod of 25 mm bore (weight not less 400 gms per running meter) incl fancy finial caps (02 nos in each curtain rod) etc complete all as specified and as directed

S & F of Brass Chromium Plated designer Bracket for curtain rod of dia 25 mm dia made out of SS Flat not less than 20 mm wide 1.50 mm thick and overall length not less than 160 mm fixed with screws min 2 Nos with Rawl Plug of size not less than 50 mm long etc complete all as specified and as directed .

Taking Down of any type of Door Shutters of any description area exc 2 sq.m each complete all as specified and directed.

Taking Down of any type of Door Shutters of any description exc 1 sqm and n exc 2 sqm each complete all as specified and directed.

S & F of Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed

S & F of small articles of steel such as hold fast, etc of Gde Fe 410- or Fe-290 Gde E-165 complete all as specified and directed.

M & L for PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in hold fast etc completed all as specified and directed.

Material and labour for preparation of wood and wood based materials, new or old, of any description and girth, not otherwise described, and treating ends of posts,back of chowkhats,etc. area tarred exc 0.1 sq m but n. exc. 0.5 sq m each and treated with tar or coal tar black paint complete all as specified and directed.

Material and labour for preparation of wood and wood based materials, new or old, of any description and girth, not otherwise described, treating small articles such as holdfasts,end of posts,backs of chowkhats, etc area n. exc. 0.1 sq m each and treated with tar or coal tar black paint complete all as specified and directed.

S & F of 35 mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers , etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S & F of factorymade 35mm thick 2nd class hardwood rail and style Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed

S & F of 30 mm thick flush shutter, solid core construction, with block board core and plywood face panel, commercial type on both sides complete all as specified and directed.

S & F of aluminium anodised 200 mm barrel tower bolts of extruded section complete all as specified and directed.

S & F of 150mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F of 100 mm butt hinges extruded aluminium alloy with galvanized mild steel hinges pin anodised type `C'-22 complete all as specified and directed.

S & F of 300mm long aluminium alloy, anodised sliding door bolt with haps, staple(bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

M & L for providing water proofing treatment to sunken portion of WCs, bathroom etc by applying cement slurry mixed with two component Elastomeric Acrylic based polymer modified cementitious composite compound coating. incl taking down existing treatment incl demolition of PCC as in sunken protion of Toilet, Bathroom etc and removing beyond the premises of site. The following procedures to be adopted during the execution of work :- (a) M & L for cleaning of the sunken / lowered portion of the RCC slab surface (including vertical total depth plus 300mm above FFL) of floors by wire brush, chiesel out any mortar sticking to the surface and brooming / washing completely. (b) Rendering of uneven surfaces with 5 mm thick CM 1:4 mixed with and incl integral liquid WPC as per mannufacturer instruction. Fill it with water and check dampness and seepage. where dampness and seepage noticed nozzles shall be fixed and epoxy grouting to be carried out. (c) All junctions points of side walls where PVC pipes are passing through shall be sealed with epoxy putty and After drying of putty, washing the slab and sides of sunken portion with water and make it clean and clear.

(d) First layer of slurry of cement @ 0.488 kg/sqm mixed with Acrylic based polymer modified cementitious composite compound @ 0.253 kg/sqm. The layer will be allowed to air cure for 4 hours. (e) Second layer of slurry of cement @ 0.242 kg/sqm mixed with with Acrylic based polymer modified cementitious composite compound @ 0.126 kg/sqm. The layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (f) Provide 40mm dia medium grade GI spout at the lowest point with 400mm long. (g) 50 mm Avg thick PCC 1:2:4 type B-0 using 12.5 mm graded aggregate as in padding conc to achieve proper slope with WPC and All pipes laid in sunken portion shall be covered with 50 mm thick PCC 1:3:6. (h) Cement concrete PCC 1:5:10 type E-2 using 20mm graded brick aggregates as in sunken portion. (j) 20mm thick screed in cement mortar 1:3 mixed with liquid water proofing compound. Note : (i) For Payment purpose, plan area of Sunken portion to be measured. (ii) Testing the water proofed area (ponding test) by filling water for atleast 72 hours and tested for leakage seepage and to the entire satisfaction of GE . (iii) Test shall be done in presence of reps of user and photographical record for each sunken slab shall be maintained. (iv) The treatment shall be carried out by authorised applicators of chemicals.

S & F of factory made 18mm thick single extruded WPC (Wood Plastic composite) solid board of any colour, texture and pattern for cup board as in Kitchen cabinet and loft shutter and similar nature of work of required sizes comporising of virsin polymer of K Value 58-60 (Suspension grade), Calcium carbonate and natural fibres(wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density 650kg/cum and screw withdrawl strength of 1800N (Face) & 900 N (Edge) , minimum compressive strength 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of Class A category with property of being termite / borer proof, water / moisture proof, and fire retardent complete all as specified and directed.

S & F of stainless steel Auto / Self closing concealed hinges 9.5 cranks for half overlay doors with opening angle 95* (14-32mm) with integrated overlay adjustment +_ 2.50mm & depth adjustment 4mm complete all as specified. Make : Godrej / Hettich as listed in Particular Specification here in after.

S & F of round stainless steel cabinet knobs handlers dia of 27mm all as specified and directed.

S & F of floor door stopper of aluminium alloy body and tongue, anodised , with hard drawn steel spring overall length of cover plate 140 mm, complete all as specified and directed.

M & L for preparation of new wooden surfaces of any description, not otherwise described,over 10 cm width or girth and applying two coats of synthetic enamel paint (ordinary paint tint) (each coat) over a coat of pink primer including scaffoldings of any hieght complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons,dados etc laid, bedded and pointed in any mortar and removal of rubbish off the site complete all as specified & as directed.

M & L for granite (of any colour) 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including grinding and polishing as in kitchen platform, counter for wash basin, flooring and all other similar works and 15mm thick screed bed mortar in CM 1:4 complete all as specified and directed.

M & L for Machine cut kota stone slab flooring 20-25mm thick ini flooring over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and 15mm thick screed bed mortar in CM 1:4 complete all as specified and directed.

M & L for Machine cut kota stone slab flooring 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing rendering 10 mm thick in CM (1:4) on fair faces of brick work complete all as specified and directed.

M & L for Chipping, Cheselling surface mechanically with chipping machine :- (1) Providing zinc rich primer for exposed reinforcement (2) Providing 100 x 100 x 3 mm weld mesh and fixing the same with shear connectors of 8mm dia with epoxy resin (3) Guniting the area with CM 1:3 of over all thickness 50mm in with two layers in small areas/patches complete all as specified and as directed .

M & L for crack repair work in walls :- Clean surface around crack, joint should be free from loose particles and dust, cutting 'V' shaped groove of size in range of 6 to 25 mm of width and depth along the crack line by machine or manually, then clean the groove by wire brush to remove loose particles and then washed by water jet, and fixing nozzle and repairing cracks using Fosroc Rendroc CS chemical with a proportion of 1 part of water to 2.5 -3.0 part of renderoc CS by volume or w/p ratio 0.36 by weight complete all as specified and as directed.

M & L for crack repair work in RCC areas :- Chipping the loose particles upto 300mm distance on both side of crack and depth 25mm behind the reinforcement bar and corrosion treatment done to existing rod and then bonding agent nitobond SBR applied to the surface, bottom shutttering to be provided before concrete pouring, and apply MICRO CONCRETE using Rendroc RG spl complete all as specified and as directed

Demolition and breaking up drain pipes upto 100/110 mm dia fixed on floor/wall (Salt glazed ware, AC, PVC or reinforced concrete) set in cement mortar complete all as specified and directed.

Demolition and breaking up drain pipes upto 75 mm dia fixed on wall/floor (Salt glazed ware, AC, PVC or reinforced concrete) set in cement mortar complete all as specified and directed.

Supply and fixing of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall/floor with suitable clamp complete all as specified and as directed.

Supply and fixing of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall/floor with suitable clamp complete all as specified and as directed.

Supply and fixing of PVC (SWR) junction single, (single T) equal or unequal provided with access door suitable for 110mm bore PVC pipes complete all as specified and as directed.

Supply and fixing of PVC (SWR) bends any radius suitable for 110mm bore PVC pipes with access door complete all as specified and as directed.

Supply and fixing of PVC (SWR) bends any radius suitable for 75mm bore PVC pipes with access door complete all as specified and as directed.

Supply and fixing of PVC (SWR) vent cowl for 110mm bore PVC pipes complete all as specified and as directed.

Supply and fixing of PVC (SWR) WC connector bent type for 110mm bore PVC pipes complete all as specified and as directed.

Supply and fixing of PVC (SWR) for 75mm Diameter of outlet floor trap, plain with grating including jointing with solvent cement etc complete all as specified and as directed.

Supply and fixing of PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and as directed.

Excavating in post holes each nexc 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers nexc 25 cm complete all as specified and as directed

M & L for PCC 1:3:6 Type C2 (using 40mm graded stone aggregate) as in foundation complete all as specified and as directed

S & F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe 290 (grade E-165) all as specified

S & F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.- 240 all as specified

S & F of MS plates (Plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment of Fe410W (Gde-E250) quality 'S' complete all as specified

M & L for preparation of new steel surfaces of any description over 10cm width or girth and priming with red oxide primer and painting with synthetic enamel painting two coats complete all as specified

S & F Prepainted galvalume aluminium zinc coating GI based corrugated steel 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & directed

Surface excavation nexc 30 cm deep and averaging 15cm deep and getting out of dense soil complete all as speicifed

M & L for 100 mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified

M & L for 100 mm thick Cement concrete type B-1, 1:2:4 (20 mm graded aggregate) for base complete all as specified

M & L for Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing com pound, Grade ‘A’ complete all as specified

Taking down carefully unserviceable point wiring copper / aluminium (light, fan, socket or power) complete, including removal of batten / conduit / gutties / wooden board etc., including fittings and fixtures such as switches, ceiling roses, regulators, sockets, light fittings, fans etc.,removal from site under Sch of credit and removal of unserviceable items out of site and making good the disturbed surfaces of walls, ceilings etc.,complete all as specified and as directed.

Point wiring on stone / brick masonry wall complete with two 1.5 sqmm single core PVC insulated FRLSH ,1100 volts grade unsheathed cable confirming to IS-694, 1977 with multistranded copper conductor, drawn through and including non-metalic rigid PVC conduit, conduit fittings and conduit accessories not less than 20 mm dia concealed in walls and fixed with suitable clamps on ceiling / roof trusses etc., and including provision of one 1.5 sqmm PVC insulated single core multistranded copper conductor FRLSH green in colour as earth continuity conductor and connected to common earth dolly, including Modular boxes, frames and cover plates all as specified complete all as specified and directed. Note : Cost of Modular box, frame, cover plates and cutting chases for concealing pipes is deemed to be included in the item rates quoted for point wiring.

One Exhaust fan point controlled by one switch.

One ceiling fan point controlled by one switch and regulator

One bell / buzzer point controlled by one bell push

One switch socket outlet 3 pin 5 Amps on same board along with other switches

One switch socket outlet 3 pin 5 Amps on independent board.

All as per item No 133.00 here-in-before but for point wiring with two 4.0 sqmm single core copper conductor multistranded FRLSH cable and one 4.0 sqmm PVC insulated single core multistranded cable as earth continuity conductor green in colour including steel box of required module for modular switches/sockets all as specified for one 3 pin switch socket outlet, 15 Amps, complete all as specified and as directed.

Supply and Fixing Modular switch 1 way 6A, 1 module complete all as specified.

Supply and Fixing Modular switch 1 way16A, 1 module complete all as specified and directed.

Supply and Fixing Modular Bell push 6A, 1 module complete all as specified and directed.

Supply and Fixing Modular Socket, 6A - 2/3 pin combined 2 module complete all as specified and directed.

Supply and Fixing Modular Socket, 6A/16A - 2/3 pin combined 2 module complete all as specified and directed.

Supply and Fixing Modular fan step regulator , 120w, 2 module complete all as specified and directed.

S&F ceiling rose 65 X 50 mm , three terminals ,bakelite , surface complete all specified and directed.

S&F Bell ding-dong type , AC, 215 volts, 50 HZ complete all as specified and directed.

S&F for Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Taking down carefully Power / Sub main wirings with PVC aluminum conductor cables in PVC/STEEL conduits / TW battens up to 2 runs of 4 Sq.mm removing materials from site, taken as credit , making good the disturbed surfaces all as specified and as directed.

Power / Sub-main wiring with PVC insulated unsheathed, FRLSH ,1100 volts, grade multistranded copper conductor, two runs of single core 6 sqmm conforming to IS-694, drawn through and including suitable dia rigid PVC conduit, conduit fittings and conduit accessories alongwith one run 6 sqmm PVC insulated single core multistranded copper conductor cable (green) as earth continuity conductor concealed in walls and fixed with suitable clamps on ceiling / roof trusses etc. and connecting to common earth dolly complete all as specified and as directed.

Supply and Fixing of Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified and directed.

S&F MCB DB SPN 08 way, double door, powder coated, 240 volts, AC, 50Hz, IP 43 protected, with provision for MCB double pole as incomer and SP MCBs as outgoing with tinned copper bus bar, neutral link, earth link and connecting up complete all as specified and as directed. Note : Incoming and Outgoing MCB measured separately relevent items

S&F Load line MCB DB TP&N 4 way, vertical, double door, powder coated, 415 volts, AC, 50Hz, IP 54 protected, fixed on wall semi flush with provision for FP MCCB 100 Amps as incomer and SP MCBs 32 amps as outgoing with tinned copper bus bar, neutral link, earth link and connecting up complete all as specified and as directed. Note : Incoming MCCB and Outgoing MCB measured separately relevent items.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and Neutral current carrying capacity 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

S&F MCCB 100 Amps 415V,16KA, 4 Pole complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20/22W, 220V,AC with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 9/10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F LED building security light fitting 30 W made up of pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, IP66 protection and impact resistance of IK07, complete pre-wired and connecting up with suitable twin core flexble copper wire including provision of necessary GI tubing medium grade 25mm bore of pipe 1.5 bent to shape with necessary clamps made out of mild steel, nuts and bolts etc., including two coats of synthetic enamel paint over a coat of red oxide primer on exposed steel surface for fixing the fitting to Bldg etc complete all as specified and as directed.

Supply & fix ceiling fans ceiling BLDC type complete with accessories 230 V,1400 mm sweep. BEE 5 star rated with provn of necesary hanging hook on ceiling complete all as specified and directed.

S&F of Exhaust fan, heavy duty, 300 mm sweep, 1425 RPM, with louvers, metal body conforming to IS, AC single phase, 240 Volts, 50 Hz and connecting including provision of two way PVC connectors, 1.50 sqmm flexible three core multistranded copper conductor cable from ceiling rose or connector to fan including earthing and fixing arrangements like making hole in wall and finishing to shape to match adjoining surface complete all as specified and directed.

S & F Ventilation fan 200mm sweep, Power 22 W, Operating voltage 230 Volts with louvers and shutters plastic body type, with necessary civil work, alteration in exist ventilation window of iron/aluminium frame for fixing of fan as per site requirement complete make good the wall/ventilation window match with exist complete with all accessories and connecting up with suitable size 1 sqmm three core copper conductor flexible wire,screws,gutties complete all as specified and directed

Material and labour for earth continuity conductor or main earthing lead fixed to valve on batten or recess or chases or burried in ground or drawing in conduit or any other situation for loop earthing etc as reqd 4 mm dia galvanized steel wire all as specified and directed

Earthing complete with galvanised iron earth plate electrode 600mm X 600mm X 6mm thick, with and including earthing of 4mm dia GI wire protected by 15mm dia GI pipe light grade upto a length of 7.5m. The plate shall be buried directly in ground vertically to a depth not less than 2.25 metres below ground level with top edge of the earth plate at a depth not less than 1.5 metres below ground level, connected to earth lead as described here-in-before by means of bolts, nuts, washers and checknuts made out of galvanised iron or mild steel, earthing lead protected by as described here-in-before and connected to main switch board or main control board or electric pole all as shown on electrical plate No.3 of MES Sch Part-I including necessary earth work and excavation in any type of soil, plain cement concrete 1:3:6, type C1 chamber, reinforced cement concrete cover slab with locking arrangement and handle of 10mm dia MS round bars 450mm long, 1:2:4 type B1, 50mm thick with 8mm dia TMT bars at 140mm centre to centre both ways, GI pipe of bore 20mm medium grade for watering with funnel, wiremesh, salt, charcoal, lugs including testing complete all as specified and as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out any type of soil for laying cables / pipes / erection of poles etc all as specified and as directed.

Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified and as directed.

Returning filling in soil including spreading leveling watering well ramming in layers not exceeding 25 cm each all as specified and as directed.

Laying in trenches fine sieved excavated dry soil including spreading/ leveling, cushioning for underground cables all as specified and as directed.

Supply and laying of common burnt clay building bricks, sub class B size for cable protection all as specified and as directed.

Material and labour for GI tubing light grade 50 mm for cable protection laid in trenches in road crossing or fixed to wall/Pole complete all as specified and as directed.

M & L for Cutting of road/path for laying of GI tubing and making the good to disturbed road/ path including provision of PCC 1:2:4 type B-1 using 20mm graded stone aggregate all as specified and directed.

Supply and fix wiring for circuit / submain wiring with two single core 4.0 Sq.mm size multistranded copper conductor of FRLSH is PVC insulated cables and one single core 4.0 Sq.mm size green colour of FRLSH is PVC insul-ated,multistranded copper conductor as earth continuity conductor,1100 volts grade, complete drawn in and including rigid PVC CONDUIT and conduit accessories, confirming to IS specifications, Concealed in wall fixing on ceiling/trusses with suitable clamps , screws etc.,including 1.22 mm thick MS terminal boxes with 3 mm thick plastic laminated sheet top cover fixed with cadmium plated iron screws for mounting switches, sockets, fan regulators etc., including connecting up and testing , all as specified and as directed.

All as per item No 174.00 hereinbefore but with four single core 10 Sq.mm size cables and two single core 10 sq.mm green colour cable as earth continuity conductor .

M&L for modular switch 1 way 230 volt 16A,1 module all as specified and directed .

Supply and fix modular socket 6A/16A-2/3 pin combined 2 module all as specified and directed .

S&F White cover plate with frame 1 module all as specified and directed .

S&F White cover plate with frame 3 module all as specified and directed .

S&F Modular metal flush box 2 module all as specified and directed .

S&F Modular metal flush box 3 module all as specified and directed .

Supply and fix electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 star rated complete with all accessories including such as safety valve, thermostate, NRV, hot and cold water Stainless steel connection pipes with PTMS nuts and washers having 600mm length etc complete all as specified and as directed.

S&F chromium plated fancy type long body Bip tap, with crutch or butterfly handle bore size 20mm dia complete all as specified and as directed.

Supplying and laying of CPVC pipes SDR11 & Plain CPVC SDR 11 fittings on walls / ceiling or laying in floors of bore size 20mm complete all as specified and directed .

Supplying and laying of UPVC pipes of pressure rating Sch 80 fixed complete to walls, ceilingsw or in floors etc, any type of pipe of bore size 25mm all as specified and directed .

S&F Ball brass valves, high pressure with flynut complete brass ferrule and fixed of bore size 25mm

S&F 240V, 10KA 'C' curve single pole MCB 6 to 32A capacity all as specified and directed .

S&F 415V 10KA 'C' curve TPN 40 to 100Amps MCB all as specified and directed .

S&F Sheet metal enclosure double door DB 415v 12 way all as specified and directed .

Supply and fixing for automatic monoblock pressure/booster pump size 25mm x 25mm, tech motor S1 class B 230 Volt 500 HZ, RPM 2800, 10 MF, input power 650 watt with pressure tank of cap 19 ltrs PS max pressure bar 10 PT test pressure bar 14 with complete accessories incl GI Pipe/gate valve/NRV complete all as specified and directed.

M&L for cutting the existing 25mm GI pipes and insert the suitable 'T' & elbow with reducer for connection of geyser inlet connections at any hight on wall, including making of hole in wall at suitable height for geyser connection and filled with white cement after connection complete all as specified and as directed. Note:- T&P required for connections at first/ second floor will be arranged by the contractor without any extra cost.

S&F PVC insulated PVC sheathed flexible copper wire 3 core multistranded conductor of size 2.5 sqmm complete all as specified and directed.

SUBAMAGENCYANDCONSTRUCTION (BID ID -3286314)

M/s Omm Muruga Enterprises (BID ID -3286816)

SWIFTTECH ENGINEERS INDIA PVT LIMITED (BID ID -3287341)

Banyan Engineers and Contractors (BID ID -3285097)

S K ENTERPRISES (BID ID -3286850)