Special Repair to Roof Flooring and Plastering at MD ACCN Block No. 46 Old MH Line Under GE (South) Bangalore

Amount

Removing existing water proofing treatment of any type and disposing off out side MD land complete all as directed.

PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) on roof slab as required to fill up the undulations and maintain the smooth slope complete all as directed

Rendering 15 mm thick in CM 1:4 on roof surfaces mixed with WPC finished even and smooth without using extra cement complete all as directed. Note: WP compound will be measured and paid seperately.

Supply only integral water proofing compound complete all as directed.

APP modified prefabricated water proofing membrane mineral finish, 3 mm thick and weighing not less than 3.60 kg / sqm reinforced with non woven polyester matt black finished over compatible primer at 0.40 Kg / Sqm and torch applications of membrane with 100 mm overlap after necessary preparation of surface top of the membrane surface shall than be finished with solar reflective aluminium paint @ 0.10 Kg / Sqm complete as per manufacturers instructions and as directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises, complete all as directed.

25 mm thick PCC 1:2:4 type B0 using 12.50 mm stone aggregate as in sub base of floor, finished even and rough to receive the topping layer complete all as directed.

Non Skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed in cement mortar (1:6) complete all as directed.

Non Skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in skirting / dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 10 mm thick screed bed in cement mortar (1:4) complete all as directed.

Non Skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed in cement mortar (1:6) complete all as directed.

Glazed coloured cermaic tiles 350 x 250 x 7 mm / 450 x 350 x 7 mm thick as in vertical surfaces of walls, set and jointed in neat cement slurry and pointed in coloured cement to match, over and including 10 mm thick rendering in cement mortar 1:4 complete all as directed.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key scrubbing down with water complete all as directed.

Rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even and smooth without using extra cement complete all as directed.

Rendering 15 mm thick on concrete surface in CM 1:6 finished even and smooth without using extra cement complete all as directed.

Preparing new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as directed.

Preparing new plastered wall surfaces, applying two coats of cement base paint over a coat of primer complete all as directed.

Complete removal of existing treatment on plastered and other surfaces and applying two coat of oil bound distemper over chalk whiting complete all as directed.

Complete removal of existing treatment and applying two coats of cement base paint over a coat of primer complete all as directed.

Preparation of new or previously untreated wooden surfaces of any description not otherwise described over 100 mm width or girth and applying two coats of synthetic enamel paint over a coat pink primer complete all as directed.

Preparation of old painted new steel or iron surfaces of any description over 10 cm width or girth and applying one coat of synthetic enemal paint complete all as directed.

Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4 mm fixed with stainless steel wire staples complete all as directed.

Hacking old brocken glass of any description from wooden or steel frame glazed with putty or wooden beads complete all as directed.

4 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beading in square / rectangular pane n.exc 0.50 sqm in each pane complete all as directed.

Disconnecting existing water tanks of capacity exc 500 ltr and n.exc 1000 ltr tanks, setting aside (or lowering if required) for repairs, cleaning etc, and hoisting if required reconnecting and re-fixing in position complete all as directed.

Taking up or down steel tubing and connections, 15 mm bore including cleaning for refixing or removal to store complete all as directed.

All as per item No. 25 but 20 mm bore

15 mm bore, steel water tubing, medium grade, galvanised with all fittings fixed to wall or laid in trenches, complete all as directed.

All as per item No. 27 but 20 mm bore

Taking down, easing, adjustment and refixing builders hardware in other opening as required including refixing building hardwares as required for shutters of any description exc 1 Sqm and n exc 2 Sqm each complete all as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm and N. exc. 4 Sq.m each complete all as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) n. exc 1.5 sqm each complete all as directed.

Second class hard wood in Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as directed.

30 mm flush door shutters, solid core construction with block board core and plywood face panels, commercial type on one side face and another face covered with decorative veneer face including liping beading all round as in door shutter, cupboard shutter and kitchen rack complete all as directed.

30 mm thick of 2 nd class hardwood glazed and skeleton shutterts open rebated and prepared to receive glass, gauge etc divided into sqaure with plain chamfered or rounded mitred and retreated sash bars any numbers edge of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members as specified in , as specified in SSR Part-I section-8, clause No. 8.24 (a) complete all as directed.

Solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet, reinforced with MS square tube and fixing in position with hold fast, complete all as directed.

Factory made solid PVC moulded door shutter, 28 to 30 mm thick (stiles), with 2, 4 or 6 raised panel design with 2 mm thick moulded prelam PVC sheet on the front face and 2 mm prelam PVC sheet on back face, supplying and fixing in frame at site as per specification and drawing complete all as directed.

Butt hinges medium weight cold rolled mild steel fixed of size 100 mm complete all as directed.

Aluminium alloy, anodised, sliding door bolts 250 mm long with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed. Complete all as directed.

200 mm long Aluminium anodised barrel tower bolts of extruded section complete all as directed.

Extruded aluminium alloy handles, fabricated type anodised 150 mm long complete all as directed.

All as per item No. 37 but 75 mm long.

All as per item No. 39 but 150 mm long.

All as per item No. 40 but 125 mm long.

Demolition of cement concrete (unreinforced ) in floors and pavings n. exc. 150 mm thickness below or above ground level complete all as directed.

PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in 75 mm thick plinth protection / path / paving finished even and smooth without using extra cement including forming groove 10 mm wide, 30 mm deep, filled with mastic filler complete all as directed.

22 mm thick chequered concrete inter locking tiles machine pressed, set and jointed and pointed in neat cement slurry as in floors over and including 20 mm thick screed bedding layer in CM 1:4, and securing properly edges of path / similar work in PCC 1:2:4 Type B1 complete all as directed.

Viterous china squating pan Orissa pattern WC of size 580 x 440 mm white with integral foot rest with 'P' or 'S' trap fixed in repair with cast iron and stoneware fitting including provn of lime concrete / cement concrete bedding complete all as directed.

Vitreous China wash down, water closet pan (pedestal pattern), and trap with plastic water closet seat black closet pattern with flat bottom and cover and mild steel chromium plated or aluminium hinginng device with flush pipe to pedestal pan including all joints and connection to drain pipe and flush pipe fixed in repair white complete all as directed.

Demolition of brick work or stone / boulder masonary, built in cement mortar including all quoins, pillars etc. but excluding ashler facing, dressed stone work or precast concrete articles complete all as directed.

Precast cement block masonry with solid blocks grade C-5, exceeding 10 Cm in width and setting in cement mortar 1:6 complete all as directed.

Gun matel gate valve 20 mm bore, with iron wheel head for iron pipe, fixed in repair complete all as directed.

Bib tap, 15 mm bore, Fancy type, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, fixed in repair complete all as directed. Make:- Ruby series of Cera or equivalent to Kohlar / Jaquar

Pillar tap, 15 mm bore, cast copper alloy, fancy type with capstan heads, chromium plated screwed down high pressure with or without lattered 'Hot' or 'Cold' with long screwed for iron pipe fixed in repair complete all as directed. Make:- Ruby series of Cera or equivalent to Kohlar / Jaquar

Stop Valve, 15 mm bore, Fancy type, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, fixed in repair complete all as directed. Make:- Ruby series of Cera or equivalent to Kohlar / Jaquar

Grating doom 125 mm dia with waste hole of PTMT. (Min wt 40 gms) complete all as directed.

75 mm bore PVC (SWR) Floor trap with grating including jointing with solvent cement to waster pipe and embedded in concrete complete all as directed.

Dismantling PVC / CI / AC drain pipe n.exc 110 mm dia complete all as directed.

75 mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches or in floor etc. complete all as directed.

PVC flushing cistern low level of 10 liter capacity white with inlet ball valve float and handle including bracket. PVC connections 15 mm size with PTMT nut of length 450 mm complete all as directed.

Vitreous china wash hand basin, fixed in repair, white flat back of size 550 x 400 mm including, CI brackets, 40 mm CP brass waste fitting, complete all as directed.

Brass chromium plated waste fitting, heavy duty, 32 mm dia for wash hand basin with long screwed shanks and fly nuts flange end beded with lead cement and other end fixed, in repair complete all as directed.

PVC waste pipe with coupling, heavy duty, 32 mm dia for wash hand basin. fixed in repair complete all as directed.

Taking down copper / aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials for taking credit (credit for above items should be made as per conditions seperately) and making good distrubed surfaces of wall, floors, etc. complete all as directed.

Taking down unserviciable main switch DB, teak wood boards etc. removing materials for taking credit (credit for above items should be made as per conditions seperately) and making good distrubed surfaces of wall, floors, etc. complete all as directed.

Wiring complete with 1.5 Sqmm single core FRLS PVC insulated unsheathed cable 1100 volts grade multi stranded with copper conforming to IS 694 drawn through and including non metalic rigid PVC conduit including accessories, concealed type, MS terminal boxes fabricated with 1.6 mm thick MS sheet fixed in wall concealed type with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch sockets outlets, fan regulators etc including provision of 1.5 Sqmm FRLS PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly for one light or fan point controlled by one way switch complete all as directed.

All as per Item No. 65 above but One 3 pin socket outlet, 5 amps, on independent board.

All as per item No. 65 but wire size 2.5 sqmm for 6 pin 15 Amps switch socket combination outlet on independent board.

Ceilling rose surface bakelite 65 x 50 mm three terminals including PVC square blocks complete all as directed.

Switch piano, flush type single pole, 5 Amps one way complete all as directed.

Switch socket combination flush type 5 Amp 2/3 pin universal multipurpose complete all as directed.

Switch socket combination flush type 5 / 15 Amp two in one 3 pin complete all as directed.

Step type electronic fan regulator, 230 volts, flush type suitable for 1200 mm sweep fan, fixing on board and making necessary electrical connection complete all as directed.

Push type, Bell Piano Switch 6 A one way complete all as directed.

Call Bell, 230 Volt Single Phase complete all as directed.

MCB single pole 6 to 32 Amps 240 volts 10 KA rupturing capacity (curve-c) providing in DB complete all as directed.

All as per item No. 75 but SPN

MCB TPN, 40 to 63 Amps, 415 Volts (C curve) providing in DB complete all as directed.

Sheet metal enclosure (ISI marked) distribution board SPN, 415 volts, 8 way horizontal type, double door with 200 Amps rated copper bus bar for housing MCBs, fixed flush in wall surface, and tested complete all as directed.

MCB, DB Double door type, made out of CRCA mild steel sheet surface mounting, TPN 4 way with 200 Amps rated bus bar, 415 volts IP-43, with PVC MCB blanking plates, stove enamelled, dust and vermin proof suitable for incorporation of MCB's and isolators etc. complete all as directed.

Sub main wiring concealed type with 3 runs of 6 sqmm, single core, PVC insulated and unsheathed cable conforming to IS-694, FRLS, 1100 volts with copper conductor multi stranded drawn in non metallic PVC conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied complete all as directed. Note:- Three run of 6 Sqmm cable, one run of of PVC non metalic conduit with all necessary accessories will be measured as one length.

LED batten suitable for indoor application 20W 4 feet length sleek and seamless profiled extruded aluminium/ polycarbonate batten with efficient diffuser and integral electronic driver including two point surface mounting on wall/ ceiling and connecting up with twin core twisted flexible copper conductor cable of suitable size including taking down existing unserviceable tube light fittings complete all as directed. Make:- C&S Cat part No. LTTB4F20W LED or equivalent of Bajaj / Polycab / Philips / Jaquar / Wipro

LED batten suitable for indoor application 10W 2 feet length sleek and seamless profiled extruded aluminium/ polycarbonate batten with efficient diffuser and integral electronic driver including two point surface mounting on wall/ ceiling and connecting up with twin core twisted flexible copper conductor cable of suitable size including taking down existing unserviceable tube light fittings complete all as directed. Make:- C&S Cat part No. LTTB2F10W LED or equivalent of Bajaj / Polycab / Philips / Jaquar / Wipro

LED Street light, 25 Watt, with pressure die cast housing along with prismatic poly carbonate diffuser and LEDs with secondary optics and IP 65 protection complete with all accesssories including connecting up with twin core twisted flexible cooper conductor cable of suitable size 24 / 0.2 mm and taking down old unserviceable Strret light fitting complete all as directed.

LED Bulk head fitting, 10 Watt, fixed in replacement with PDC Aluminium housing and milky diffuser complete all as directed. Make:- Bajaj Cat part No. BIBWP10WLED / C&S Cat No LTB10WLED / Crompton Cat No LBH-10-CDL.

Exhaust fan, metal body, single phase 230 volts AC of 300 mm sweep, 1400 RPM with louvers and connecting up with provision of porciline connector and flexible three core copper conductor of 0.5 sqmm size from terminal point complete all as directed. Make:- Bajaj model Freshee MK-II product code 70003 or equivalent of Crompton / Havells

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (Earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connecting with steel GI earth wire 4 mm dia by means of bolt nut check nuts and washers including PCC pit with 1:2:4 type B-1 using 20mm graded stone aggregate and frame cover of angle iron 25x25x6mm, MS sheet 3mm thick and handle of 6mm dia MS bar made to shape, GI medium grade 20mm bore pipe for watering common salt chorcoal funnel wiremesh earth work in any type of soil returning filling in and removal of soft/loose soil to a distance n.exc 5 mtr including earth test point and making connections testing on completion all as per electric plate No 3 of SSR Part-I, complete all as directed.

Excavation in trenches n.exc 1.5 M wide and n.exc 1.5 M depth for foundation or cable trench or for shafts, wells, cesspits, manholes pier holes etc. n.exc. 10 Sqm on plan and n.exc. 1.5 M in depth and getting out in hard / dense soil complete all as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers, not exceeding 250 mm thick, each layer, complete all as directed.

Removing excavated material to a distance not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the staring point complete all as directed.

River sand to required width at bottom and top for cable cushioning (8 cm before laying the cable and 15 cm after laying the cable) complete all as directed

Common burnt clay old size bricks of sub class B (designation 75) laid at right angle to the cable in trenches for cable protection complete all as directed.

PCC 1:3:6 type C1 using, 20mm graded stone aggregate for make good to road surface, hard standing etc complete all as directed.

Supply, laying, jointing, testing and comissioning, cable XLPE insulated, armoured and PVC sheathed LT 1100 volts grade and aluminum conductor confirming to IS 7098 laid in trenches / through pipe / floor / fixed wall etc. for size of cables 35 Sqmm 3.5 core complete all as directed.

GI pipe 40 mm bore, light grade, as in cable protection under road / floor / fixed to wall / panel etc. complete all as directed.

M.VENKATARAMANAPPA AND COMPANY

VIKAS CONSTRUCTIONS

M/S Bhagyawanticonstruction

K. VENKATESH NAIDU

sri sai construction

OM CONSTRUCTIONS