SPECIAL REPAIR TO IRON ROLLING SHUTTER REPLACEMENT OF COMPLETE ROOF ACC SHEET WITH CGI SHEET FALSE CEILING FLOORING WITH KOTA STONE AND SIDE WALL TILLING WORK IN BUILDING NO 41 OF 622 PARA COY ASC COMP UNDER GE W AGRA

Amount

Demolition of reinforced cement concrete roof, shelves and similar suspended work complete all as specified and directed.

Dismantling cement (corrugated semicorrugated, etc) sheets in roof covering including 'L' type or 'J' type hooks or cranked bolts etc complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet for ridges 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling timber scantlings 40 Sq. cm and over in section and in any position complete all as specified & directed.

M&L reinforced cement concrete nominal mix 1:2:4, typeB-1 (using 20 mm graded stone aggregate) in slab/shelves supported on walls the like all as specified and directed.

M&L reinforced cement concrete nominal mix 1:2:4, typeB-1 (using 20 mm graded stone aggregate) in beam, lintel over 1.50mtr length and the like all as specified and directed.

M&L TMT bars of 10mm dia and over, dia cut to length bent to shape required including cranking bending spirally, hooking ends and binding with mild steel wire not less than 0.9 mm dia(annealed) complete all as specified and directed.

Mild steel TMT bars 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with, in stirrups and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Use &waste of formwork to sides and soffits of beam, lintel etc rough finished surfaces of concrete all as specified and directed.

Use & waste of formwork to side/soffits slab/shelves etc rough finished surfaces of concrete all as specified and directed.

S&F mild steel joist channel angle or 'I' sections fixed independently with out connecting plates etc of grade Fe-410-0 & Fe 310-0 complete all as specified and directed.

S&F rolled section as in main and cross beams hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc confirming to Fe-290 grade E-165 complete all as specified and directed.

M&L for preparation of new steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for PCC 1:2:4, type B-1 (using 20mm graded stone aggregate) as in bed block, copping and embedding of hold fast etc including necessary use & waste of formwork complete all as specified and directed.

Demolition of brickwork built in cement mortar including all quoins arches pillar etc. complete all as specified and directed.

M&L brick work (old Size) in cm (1:6) straight or curved on plan exceeding 6.00 mtr mean radius complete all as specified and directed.

Taking down cement plaster on brick or stone walls including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick on any faces of brick work in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered of wall and applying three coats of white wash complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 with water proofing compound as per manufacturer's instructions on any faces of brick or concrete surfaces of walls & finishing the surface even and smooth without using extra cement complete all as specified and directed. Note: WPC will be measured & paid separately.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for preparation of new plastered or un-plastered surfaces of wall and applying two coats of cement base paint over a coat of priming paint complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

M&L for glazed ceramic coloured tile 350x250x7mm / 450x350x7mm thick jointed and pointed with white or coloured cement over & including 10 mm thick rendering in cm 1:4 complete all as specified and directed.

Roughening of surface of old concrete floor by picking sweeping clean and washing down with water to remove dust etc complete all as specified and directed.

M&L for non-skid ceramic coloured tiles joint free 7 to 8 mm thick (Square /rectangle) area of each tile excedding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and ponted in white or coloured cement to match over & including 15 mm thick scread bed in cm 1:6 complete all as specified and directed.

M&L Machine cut kota stone 20-25 mm thick as in floor, laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and mirror polishing over & including 20mm thick screed bed in CM (1:4) as in floor complete all as specified and directed.

M&L Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado laid over 10mm cement plaster in CM (1:4) and jointed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed.

Dismantling wall and ceiling boards (fibre pulp, insulation etc.) or insulation board /slabs/blanket any thickness including cover fillets complete all as specified and directed.

S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre complete all as specified and directed.

M&L for 4 mm thick non asbestos fibre cement building designer boards fixed in ceiling or laid/inserted to timber / GI / aluminun frame complete all as specified and directed.

S&F solid PVC Wall lining consisting of 5mm thick plain single side prelam PVC sheet light colour inclusive of solvent cement and fixing at site on PVC frame complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame complete all as specified and directed.

M&L 18 to 20mm thick granite (of any type) slab machine cut, over platform and skirting/ dedo laid over cement screed and jointed with grey cement cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

Demolition Cement concrete (unreinforced) in ground floors and pavings n exe 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for PCC 75mm thick 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection laid in alternate pannels, finished even and smooth without using extra cement complete all as specified and directed.

Taking down rolling shutter of size exc 8 Sqm n.exc 12 Sqm complete all as specified and directed .

S&F steel rolling shutters but gear operated type with bevel gear box and crank handle, thickness of laths 1.25mm, as specified including top cover, anchoring rod, hasp and staple and eracted in position as directed complete all as specified and directed. Note: Ball bearing willbe measured & paid separately.

S&F ball bearing for rolling shutters complete all as specified and directed.

S&F safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.

Taking down carefully copper/aluminium point wiring on batten/ PVC conduit (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc, including removal and making good disturbed surfaces of walls, ceilings etc by cement/ colour /plaster to match with the existing location spot complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC FRLS insulated, unsheathed, single core, multi stranded copper conductor cable 1100 volts grade including 1.5sqmm FRLS PVC insulated unsheathed stranded copper conductor cable as earth continuity conductor drawn in and including rigid PVC conduit of suitable size but not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0 mm thick ISI marked plastic laminated sheet cover for fixing switches/ socket/regulators etc including cutting chases in wall as per standard engineering practice & making good the disturbed surfaces to match with existing for the one light/ fan/street/bell point controlled by 1 one way switch 5/6 Amps complete all as specified & directed.

All as per item No-43 here in before but One socket outlet 5/6 Amps on independent bd controlled by one switch complete all as specified & directed.

All as per item No-43 here in before but One socket outlet 5/6 Amps controlled by one switch on same board with other switches complete all as specified & directed.

All as per item No-43 here in before but one socket out let 3/5 pin, 5/6 Amps controlled by one 1way switch on independent board but not below the switch board of light points in same vertical plane complete all as specified & directed.

All as per item No-43 here in before but using 2.5 sqmm PVC FRLS insulated stranded copper cunductor cable and for one socket out let 3/6 pin, 15/16 Amps controlled by one 1 way switch on independent board complete all as specified & directed. NOTE-For item no 43 to 47 -: (i)The quoted rates shall be deemed to be inclusive for cutting chases in brick walls/pillers etc for concealing the conduits to required depth & making good the disturbed surfaces in cement mortar 1:4 including finishing the surface to match with the existing surface.The portion of point wiring at RCC Coloumns/Beams/Ceilings etc shall be in surface conduit of suitable size fixed on surface with using PVC rawl plug and provision of covering terminal boxes/junction boxes of any shape and size with 3 mm thick bakelight laminated sheet fixed with suitable GI screws and cup washers. (ii) Fittings like switches, sockets, regulators, lamp holders, light foittings shall be measured and paid for separately under appropriate item of schedule A. (iii)The size of conduits shall be determined on permissible no of runs of wires as specified in SSR part-I clause 19.125 (B).However minimum size of conduit shall be 20 mm dia (medium grade)

S&F switch piano, flush type, single pole, 5/6 Amps one way, 230 volts complete all as specified and directed. Make: Anchor Cat No.38058 or equivalent as approved by GE.

S&F switch piano, flush type, single pole, 15/16 Amps one way, 230 volts complete all as specified and directed. Make: Anchor Cat No.39991 or equivalent as approved by GE.

S&F socket outlet, 5/6 Amps, flush type, 5 pin 230 volts complete all as specified and directed. Make: Anchor Cat No.38320 or equivalent as approved by GE.

S&F socket outlet, multi-purpose 3 pin 5/6 Amps and 3 pin 15/16 Amps complete all as specified and directed. Make: Anchor Cat No.39994 or equivalent as approved by GE.

S&F for ceiling rose surface bakelite 62.5 x 25 mm size 3 terminals complete all as specified and directed. Make -Anchor CAT Part No-39072 or equivalent as approved by GE.

S&F lamp holder insulated body with back plate for batten fitting complete all as specified and directed. Make: Anchor Cat No. 39797/ 39800 or equivalent as approved by GE.

S&F rotory stepped type electronic fan regulator mini flush type 100 watt 230 Volts complete all as specified & directed. Make: Anchor Cat No.38284/38660 or equivalent as approved by GE.

S&F in repairs LED Bulb 15 watt, single phase, 230 Volts AC supply suitable for lamp holder complete all as specified and directed. Make :- Havells cat part No-LHLDDEEEML8R015 or equivalent Model of Philips/Bajaj/CG/ Wipro as approved by GE.

S&F in repairs surface/wall mounting LED batten 20 watt luminaire having extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver with mounting accessories complete with lamp holders fixed to wall/ ceiling with fixing accessories and connecting up with & including twin twisted copper flexible wire of size 0.75 sqmm from ceiling rose to fittings complete all as specified & directed. Make:- Havells cat part No-ENDURALINEARNEOBS20WLED865SPCWH or equivalent Model of Philips/Bajaj/CG as approved by GE.

S&F in repairs outdoor security light LED 36/40 watt luminaire IP 65/66 protection polyster powder coated with pressure die cast aluminium housing and robust construction with reflector cover pre anodised and flat white high transmission acrylic cover or toughened glass, natural white type with electronic driver, connector block etc with internally prewired fixed to building with and including 1.20M long bracket made out of 40mm dia light grade GI pipe bent to shape & providing clamps 2 Nos made out of 50 x 6 mm Flat iron/MS clamps & 12mm dia bolts, nuts & washers etc and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed. Make:- Havells cat part No- ENDURAPEARLNEOSL40WLED757PASYTOPC,Phillips cat part no BRP052 LED 036 CW HP SLA FG S1 PSU GR or equivalent as approved by GE.

S&F in repairs LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make:- Havells cat part No- LHECDEFOIH1W028 or equivalent model of make ,Philips/Bajaj/ Crompton Greaves as approved by GE.

S&F in repairs surface mounting type bulkhead 10 watt LED luminaire ENDURA RUGBY NEO IP 65 environmental friendly, altra modern energy saving , decorative oval comprising of high brightness LEDs, connector block etc with internally prewired fixed to wall with fixing accessories and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed. Make:- Havells cat part No- Cat part No FT10WLED857SSYMBOPC or equivalent model of make Philips/ Bajaj/ Crompton Greaves as approved by GE.

Taking down distribution boards any size any type including MCB TPN/SPN/SP etc and making good the disturbed surfaces complete all as specified and directed.

S&F MCB DB vertical type 4 way VTPN sheet metal enclosure 415 volts with 100 Amp fully insulated standard copper bus bar for each face & surrounded with neutral bars and two common neutral bar, two earth bar including cable ties for cable manegement suitable for housing MCCB TPN 415 Volts as incommer, IP-43, IK-09 as per IEC 61439-3 with metal doors all enclosed on standard steel sheet flush mouting type double door factory fabricated complete without MCB & MCCB but with enclosue blank plate complete all as specified and directed . Make:- Legrand CAT No.507725 or equivalent model of make Siemens/ Schneider as approved by GE.

S&F MCB DB sheet metal enclosure factory fabricated double door SPN 8 way with 100 amps rated copper bus bar 240 volts IP-43, IK-09 with metal doorscomplete all as specified and directed. Make:- Legrand Cat Part No. 5076 11 or equivalent model of make Siemens/ Schneider as approved by GE.

S&F MCCB 4 pole 100 to 125 Amp Icu 16 Kilo Amp and Ics 100% of Icu with adjustable 70% to 100% and thermal magnetic release suitable for fixing in VTPN DB. Make : Legrand cat part 4200 15 to 4200 16 or equivalent model of make Siemens/ Schneider as approved by GE.

S&F Isolator SPN , 40 Amps, 240 volts, 50Hz, IP-20 as per IEC 60947-3 ISI marked complete all as specified & directed. Make:- Legrand CAT No. 4065 01 or equivalent model of make ABB/ L&T/ Schneider as approved by GE.

S&F MCB SP, 40 to 63 Amps, 'C' Curve, 240 volts, 50Hz, 10kA IP-20 as per IS/IEC 60898-1 2002 ISI marked complete all as specified & directed. Make:- Legrand CAT No. 4085 96 to 4085 98 or equivalent model of make Siemens/ Schneider as approved by GE.

S&F MCB SP, 6 to 32 Amps, 'C' curve, 240 volts, 50Hz, 10kA IP-20 as per IS/IEC 60898-1 2002 ISI marked complete all as specified & directed. Make:- Legrand CAT No. 4085 87 to 4085 95 or equivalent model of make Siemens/ Schneider as approved by GE.

Taking down care fully sub main wiring / service connections of any size including batten/ conduit, and making good the disturbed surfaces of wall/ floor complete all as specified and directed.

M&L for sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 6.0 sqmm drawn in and including rigid PVC rigid conduit medium grade of suitable size but not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, stranded copper conductor cable of size 6.0 sqmm as earth continuity and cutting chases to wall as per standard engineering practice & making good the disturbed surfaces as per existing complete all as specified & directed. Notes:- Finished sub main wiring with two runs of 6.0 sqmm cable & one run of 6.0 sqmm cable alongwith PVC conduit including its accessories shall be measured and paid one unit length.

M&L for sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 4.0 sqmm drawn in and including rigid PVC rigid conduit medium grade of suitable size but not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, stranded copper conductor cable of size 4.0 sqmm as earth continuity and cutting chases to wall as per standard engineering practice & making good the disturbed surfaces as per existing complete all as specified & directed. Notes:- Finished sub main wiring with two runs of 4.0 sqmm cable & one run of 4.0 sqmm cable alongwith PVC conduit including its accessories shall be measured and paid one unit length.

M&L earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm size, buried directly in ground (earth pit not less than 2.25 M deep below normal ground level) with top edge of the plate not less than 1.5 M below normal ground level connected to and including galvanised steel earth lead wire of 4 mm dia, including 15 mm bore GI light grade protection pipe upto 1 Mtr above the floor level of the buildings where main switch, DB etc, situated, earth lead wire connected to the earth plate by means of GI bolts, nuts, washers and earth plate surrounded by 150 mm thick alternate layers of charcoal or cock dust mixed with common salt 20 mm bore medium grade GI watering pipe PCC pit in PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) cover of precast RCC 1:2:4 type B-1(using 20 mm graded stone aggregate) duly reinforced with 8 mm formed or twisted bars @ 100 mm c/c both ways, GI wire mesh, GI sheet funnel necessary excavation in soft/ Looose soil and deposited the surplus soil to a distance not exceeding 50 mtr away from starting point, all as per electrical plate no:3 of SSR part-1 .

M&L for electrically disconnecting and taking down existing ceiling/Exhaust fans from any hight or in any position from existing bldg and keeping in safe custody for reuse at site after necessary repare/ servicing & painting with one coat of synthetic enable paint and writing of MES/identification No. of fans and re hanging/ re-fixing in original position but including replacement of three cor flexible copper conductor cable from ceiling rose to fan connector block of soze 0.75 Sqmm and hanging fan clamps, nuts, bolts and rubber reel bush etc & testing for proper functioning complete all as directed.

Supply & Laying, testing, cable XLPE insulated screened PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) 1100 volt grade, with stranded aluminium conductor of size 25 Sqmm 4 core compele all as specified and as directed.

Supply and fixing GI Pipe 50mm Light grade, for cable protection laid in trench under road or path or fixed on pole or wall with clamps with all fittings complete all as specified and as directed.

Excavation in trenches n.exc 1.5 mtr wide and n.exc 1.5 mtr deep in soft/loose/ soil for taking out/laying CI/GI pipe line and getting out soft/loose soil complete all as specified and as directed .

Returning, filling in including spreading, leveling, watering and well ramming in layers n.exc 25 cm thick layers complete all as specified and as directed.

Removal of excavated material n.exc 50 mtr away and depositing where directed at a level n.exc 1.5 mtr above from starting point complete all as specified and as directed.

Supplying and laying un-rainforced precast concrete cable cover LV type-I flat size 250 mm x 150 mm x 40 mm in trenches for protection of cable complete all as specified and as directed.

M&L for sand cushioning dry fine for cable cushioning below and above the cable complete all as specified and as directed.

PD GUPTA AND COMPANY

M/s Salim Mohomad

Balaji Associates

M/S SHRINATH CONTRACTION

MESSARS JAI AMBEY BUILDERS

N.K. ENTERPRISES

M/S RISHI RAJ AGRAWAL