SPL REP TO GUARD POST NO. 32 WITH TOILET BLOCK AND PATHWAY SINGLE OFFR LVG ACCN P-76 AND PROVN OF 01 X BATHROOM WITH TOILET A JCO LVG ACCN AT MIL STN JASAI UNDER GE A BARMER

Amount

Taking down cement plaster on stone masonry/Brick Masonry incl racking out joints, hacking for key scrubbing down with water and direction by Engr- In Charge.

M&L for 10 mm thick rendering in CM 1:6 on fair face of brick work or on concrete surface finished even and smooth without using extra cement complete all as specified and directed.Z

M&L for 5 mm thick rendering in CM 1:3 on fair face of ceiling or on concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in CM 1:4 on fair face of External wall, concrete surfaces /RCC surfaces/soffits of chajjas/roof projection/cantilivers/balcony etc finished even and fair with water profinfing compound (WPC) complete all as specified and directed.(WPC Measured seprately)

Supply only liquid water proofing compound ( For external new plaster surfaces)

M &L for Preparation of new plastered surface of wall and applying two coat of oil emulsion distemper of approved tints over a coat of interior wall primer complete all as specified and directed by Engineer-in-Charge..

M&L for preparing new plastered surfaces of ceilings and applying two coat of oil emulsion distemper of approved tints on ceiling over a coat of interior wall/ceiling primer complete all as specified and directed by Engineer-in-Charge..

M&L for preparing new plastered surface of wall and applying Two or more coats of 100% Premium acrylic emulsion paint of required shade, on external walls/RCC surfaces/soffits of chajjas/roof projection/cantilivers/balcony etc having VOC less than 50 gM&Litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm, including necessary scaffolding arrangement as required at site complete all as specified and-as-directed.

M&L for complete removal of existing treatment incl preparation of wall surfaces and fill the crack of wall with crack filler paste and applying two coat of oil emulsion distemper of approved tints over a coat of interior wall primer, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old plastered surface of Ceiling and fill the crack of ceiling with crack filler paste and applying one coat of oil emulsion distemper of approved tints complete all as specified and directed by Engineer-in-Charge..

M&L for complete removal of existing treatment incl preparation of wall surfaces and fill the crack of wall with crack filler paste and applying Two or more coats of 100% Premium acrylic emulsion paint of required shade, , having VOC less than 50 gm/Litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm, including necessary scaffolding arrangement as required at site complete all as specified and-as-directed.

Preparation of old decorated wooden surfaces of any description, not otherwise described over 10cm width & girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old decorated steel surfaces of any description, not otherwise described over 10 Cm width & girth and applying one coat of synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames (without taking off shutters from the frame) n. exc 1.5 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified.

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm each and complete all as specified and directed.

Taking down door/ windows incl frames and complete fittings of area exc 1.50 sqm but n. exc 4 sqm complete all as specified and as directed.

S & F Pressed steel frames made of MS sheet of 1.20mm thickness of size 105 x 60 mm for doors with single or double rebate including necessary fixing lugs, hinges, lock strike plate, hold fasts, PCC 1:3:6 type C-0 in fillinng inside frame & hold fasts etc complete all as specified. (Note :- Distrubed protion of existing floor/ wall/ tile/ plaster etc during fixing of chowkhats shall be replacemented to match with exisitng finish. Cost of the same will be included in this items). As approved by Accepting Officer

Supply and fixing 30mm thick flush shutters, solid core construction, with block board core and plywood face panels,commercial type on both sidesa all as specifid and directed incl S & F fwg items As approved by Accepting Officer. (a) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (b) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16 x 300mm-1 No per leaf (d) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 No per leaf

S & F 35mm thick glazed and skelton shutters of 2nd class hard wood (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-I section 8 clause 8.20 (a) kiln seasoned and chemically pressure treated all as specifeid including stainless steel 304 grade wire cloth ( 0.36mm nominal dia of wire and average width of aperture 1.40 mm ) and incl supply and fixing following items:- (a) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf (b) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x3000mm - 1 nos per leaf (d) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos per leaf

S&F for one side decorative laminated sheet (sunmica) not less than 0.9mm thick and other side plain white/ decorative laminated sheet as reqd, and fixed at flush door using, fevicol etc. complete all as specified and directed.

S&F in replacement 100mm size SS butt hinges and fixed to PVC frame /Wooden Frame and angle iron frame by necessary welding complete all as directed.

S&F for mild steel ordinary rat tail rod pattern spring 300mm size including roller & roller plate and incl welding complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description, over 10cm in width or girth, not otherwise specified with two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

M&L for powder coated aluminium frame and shutter for door, window, ventilators, partion and sliding shutters etc ( Minimum thickeness of powder coating 50 micron) with one or more rebates including jointing cleat, aluminium snap beading 20 x 15mm, rubber gasket, glazing clip for fixing etc .complete all as specified and directed by Engr in charge.

S&F for powder coated aluminium grill made out of 7mm x 4.5mm w'ide flat, square ractangular or similar section, fixed with channel of size 38mm x 12mm x 13mm (section 8778 complete all as specified including taking down (make: DECO GRILL No. DG 102 with aperture- 80mm or equipment as approved by GE.

S&F 4mm thick tinted sheet glass of approved make and shade/tint filling in aluminium panels door/window/partion with necessary joining cleats, beading all as specified and directed.

M&L 2mm thick wall care putty on wall complete all as specified and-as-directed.

S&F in replacement stainless steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or stainless steel wire staples or with aluminium / wooden beads, stainless steel screws and nuts bolts etc for ventilator complete all as specified.

S&F brass 4 levers mortice lock, vertical type, size 100mm for aluminium door complete all as specified and directed

S&F Aluminium door closer hydraulically aluminium die cast body regulated designation No. 2 universal type (ISI Make) suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 Kg complete all as specified.

S&F powder coated aluminium, three track sliding window frame of section size 92.00x 31.75x1.3mm comprising of one No of fly proof shutter and two nos of glazed shutter frames of section size 32x18x1.3mm thick with necessary joining cleats, glazing clips, rubber gasket, anodised aluminium snap beading and connected locking arrangement all as specified and directed. (Notes. (i) Glass filling in panels of window and stainless steel wire mesh/wire cloth shall be demed to be included in the quoted rate for the item, ii) stainless steel wire cloth in panels of fly proof shutter shall be 0.36mm nominal dia of wire and avg width of aperture 1.40mm, fixed with aluminium wire staples,. iii) Glass filling in panels of glazed shutter shall be 4mm thick tinted sheet glass of approved make and shade/tint (Make of aluminium sections powder coated: Make Jindal/INDAL/Hidalco).

S&F in replacement Aluminium door closer hydraulically aluminium die cast body regulated designation No. 2 universal type (ISI Make) suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 Kg complete all as specified.

S&F in replacement Stainless steel tubing of 20 mm dia chromium plated min. 1.0 mm wall thickness as in curtain rod complete incl S&F 02 Nos stainless steel brackets & finials fency type, stops fixed with ss screws etc all as specified & directed as in replacement . Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered as approved by accepting officer.

S & F in replacement 200 mm long SS tower bolt (304 Grade) fixed with SS screw, complete all as specified and directed

S & F in replacement SS (304 Grade) bow handle, of 200 mm long fixed with SS Screw complete all as specified and as directed.

S & F in replacement SS (304 Grade) sliding door bolts of 300mm long with hasp and staple(bolt type) and fixing clips of sheets , fixing bolts and sliding bolts of extruded section with SS Screw, complete all as specified and directed.

S&F in replacement 140 mm floor door stopper of aluminium alloy body and tongue , anodised ,with hard drawn steel spring ,fixed in floor complete all as specified and directed

Dismantling boarding, of Aluminium / Ply / Wooden of any description, fixed in any position with screws. complete all as specified and directed

S&F in replacement BWP/Marine Pllywood for, Shelves, Cup Boards, wardrobes, Kitchen Cabinets, moduler kitchen etc 18/19 mm thick, as per directed with one side decorative laminated sheet (sunmica) not less than 0.9mm thick and other side plain white laminated sheet as reqd, and fixed using self tapping SS screws, fevicol etc. complete all as specified and directed.

S&F stainless steel bow handle not less than150mm long, complete all as specified and directed.

S&F stainless steel frog hinges suitable for Shelves, Cup Boards, wardrobes, Kitchen Cabinets etc for smooth movement. complete all as specified and directed.

S & F for Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet, fixing of float valveand over flow pipe if required etc including taking down existing tank complete .

S&F in replacement for 16mm bore of CPVC of food grade pipes SDR 11 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking down or up existing GI tubing/CPVC pipes & connections all as specified and directed by Engr-in-charge.

S&F in replacement 20mm (OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/ walls and ceiling including taking down or up existing GI tubing / CPVC pipes & connections all as specified and directed by Engr-in-charge.

S&F in replacement 15 mm dia bib tap,fancy type chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified anddirected.

S&F in replacement 15mm bore CP fancy type stop valves/angle cock, cast copper alloy, screwed both ends for iron pipe or for union complete all as specified and as directed.

S&F in replacement 15mm dia Bib tap (2 in 1 type) of brass, chromium plated fancy type glossy finish fixed in replacement complete all as specified and directed.

Supply & Fixing in replacement Corner glass shelf size 200 mm radius with and including bracket and glass complete set etc.

Supply & Fixing in replacement Toilet paper Holder fancy type with flat recessed type stainless steel fixed to wall etc complete all as specified and directed Engrs-In Charge.

S&F in replacement 15mm bore centre hole basin mixer fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' and `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in replacement brass CP wall mixer 2 in 1 with provisiion for overhead/hand shower suitable for 15mm bore pipe complete all as specified and directed

S&F in replacement Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed.

S&F in replacement chromium plated swivel shower roses with or without swivel joints, for fixing with 15mm pipe fixed all as specified

S&F in replacement Sheet glass shelf fancy type assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed

Supply & Fixing in replacement stainless steel Towel Rack with lower hanger size 24'' (600 mm) fixed to walls with hook etc.

S&F in replacement PVC connection 15mm bore length not less than 600 mm long with both ends PTMT nuts complete all as specified.

S&F in replacement 32/40 mm bore waste fittings, brass, chromium plated for sinks, basins etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete.

S&F in replacement 110mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid on trenches or in floors /wall complete all as specified and as directed.

S&F in replacement of premium/1st quality vitreous china EWC one piece Single Piece WC with PP Soft Close Slim Seat Cover, Hinges, Dual Flush Cistern Fittings, Fixing Accessories And Accessories Set, Size: 360x660x755 mm, S Trap- 220 mm, including taking down old vitreous china EWC and cistern, complete all as specified and directed. Make:- Cera/Hindware/Jaquar

S & F in replacement Vitreous china premium/1st quality wash basin, white, size 550x400 mm including S&F all accessories as recommended by manufacturer complete fixed in position in all respect as per manufacturer's instructions and all as specified including all Waste fittings, brackets, brass,chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, complete all as specified and directed. Make:- Cera/Hindware/Jaquar

S & F in replacement Flushing cistern of PVC 10 ltr. cap. with dual flushing system, valveless syphonic action type, low level, white/ivory/off white with inlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete in all respect all as specified. Make:- Cera/Hindware/Jaquar

S&F in replacement grating doom 125mm dia with or without waste hole of Stainless steel / PTMT (minimum weight 40 gms) complete in all respect all as specified.

Demolition of stone / boulder masonry walling built in cement mortar including all quoins arches pillars etc and removal unserviceable materials, debris, rubbish to out side MD land complete all as specified and as directed.

M&L for precast-cement concrete block masonary with solid blocks type D-1 ,1:3:6 (20mm graded aggregates) exc 10 cm in width and setting in CM 1:4 ,complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding, removing serviceable tiles to stores and removing debris outside the MD land,complete all as specified and directed

M&L for 300mmx300mmx10mm thick non skid polka dots parking floor paver tiles with grey cement and pigment, over and including 15mm thick screed in CM (1:4), set jointed & pointed in neat cement slurry in floors complete all as specified and directed.

S&F Non-Skid ceramic Coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:4,complete all as specified and directed

S&F Vitrified ceramic tiles in light shade 10mm thick (square/ractangular) polished,area of each tiles not exc 0.36 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6, complete all as specified and directed

All as per item No. 69.00 here-in-above but as in skirting over cement mortar backing plaster in CM1:4 15mm thick

M&L for Glazed ceramic glossy finish tiles coloured in vertical surface 450X300X7mm in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified.

Demolition of concrete in ground floors and paving n exc 15cm thickness (below or above ground level ) complete all as specified and directed

M&L for 25mm thk PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in subbase of floors & finishing the surface even & smooth without using extra cement,complete all as specified and directed

M&L for cement concrete in foundations, filling and mass concrete type D2 1:4:8 (40mm graded aggregate)

Dismantling structural steel work including doors gates but excluding framed truss etc complete all as specified and directed

S&F for hollow,rolled sections as in main and cross beams, column, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conf to Fe-410-w or E -250 quality A complete all as specified and directed.

M&L for 10 mm rendering in CM 1:4 on fair face of wall or on concrete surfaces finished even and fair with water profinfing compound (WPC) complete all as specified and directed.(WPC Measured seprately)

M&L for Preparing New plaster surface of Ceiling and applying three coat of white wash on ceiling complete all as specified and and directed

M&L for preparation of new plastered surfaces of external walls/RCC surfaces/soffits of chajjas/roof projection/cantilivers/balcony etc including cornices and applying two coat of cement base paint as Camoflage pattern over a one coat of of external primer.complete all as specified & as directed by engr-in-charge.

Preparation of old surfaces of ceiling (plastered or unplastered) by brooming or steel wire brushing, scrapping down smoke spot moulds, moss efflorescent salts and trading oil greasy spot and fill the crack of ceiling with crack filler paste and applying one coat of white wash on ceiling complete all as specified and directed by Engineer-in-Charge..

M&L for complete removal of existing treatment of any type/description such as cement base paint,external emulsion etc from external surfaces of walls/RCC surfaces/soffits of chajjas/roof projections/cantilivers/balcony etc with mechanical means/grinder and preparing existing treated surfaces of external walls/RCC surfaces/soffits of chajjas/roof projection/cantilivers/balcony etc including cornices and fill the crack of wall with crack filler paste and applying two coat of cement base paint as camouflage / ordinary pattern over a coat of primer by complete all as specified & as directed by engr-in-charge. Note for above items of external finishing :- the cost for steel tubular double scaffolding necessary for execution of work and protective measures for height more than height of double storey building as directed by engr-in-charge shall be included in the quoted rate against the respective item and nothing shall be admisible for this.

S&F powder coated aluminium, three track sliding window frame of section size 92.00x 31.75x1.3mm comprising of one No of fly proof shutter and two nos of glazed shutter frames of section size 40x18x1.3mm thick with necessary joining cleats, glazing clips, rubber gasket, anodised aluminium snap beading and connected locking arrangement all as specified and directed. (Notes. (i) Glass filling in panels of window and stainless steel wire mesh/wire cloth shall be demed to be included in the quoted rate for the item, ii) stainless steel wire cloth in panels of fly proof shutter shall be 0.36mm nominal dia of wire and avg width of aperture 1.40mm, fixed with aluminium wire staples,. iii) Glass filling in panels of glazed shutter shall be 4mm thick tinted sheet glass of approved make and shade/tint (Make of aluminium sections powder coated: Make Jindal/INDAL/Hidalco).

M&L anodised aluminium frame for ,ventilators, sliding shutters etc with one or more rebates for fixing etc .complete all as specified

S&F anodised aluminium grill made out of 7mm x 4.5mm w'ide flat, square ractangular or similar section, fixed with channel of size 38mm x 12mm x 13mm incl taking down (section 8778 complete all as specified (make: DECO GRILL No. DG 102 with aperture- 80mm or equipment as approved by GE.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as specified and as per drawing.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification incl the fwg S & F As approved by Accepting Officer (a) Mild Steel Butt Hinges 125mm - 3 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf

Supply and fixing 35mm thick flush shutters, solid core construction, with block board core and plywood face panels,commercial type on both sidesa all as specifid and directed incl S & F fwg items As approved by Accepting Officer. (a) Mild Steel Butt Hinges 125mm - 3 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16 x 300mm-1 No per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 No per leaf

S&F for Rotational moulded polyethylene water storage tanks of 500 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete .

S&F in replacement Stainless steel tubing of 20 mm dia chromium plated min. 1.0 mm wall thickness as in curtain rod complete incl S&F 02 Nos stainless steel brackets & finials fency type, stops fixed with ss screws etc all as specified & directed. Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered as approved by accepting officer.

Supply & Fixing in replacement 25 mm bore tubes medium grade galvanized with all fitting such as Tee, elbows, sockets, unions, plugs, short lenghts etc and fixed complete to walls and ceilings or laid in floors of any length including taking down or up existing GI tubing & connections all as specified and directed by Engr-in-charge.

Cutting chases, pinning in making good to facing on brick walls & pointing in CM 1:3 for concealed water tubing cutting n exc 10 cm girth all as specified and as directed.

S&f in replacement 15mm bore pillar tap cast copper alloy fancy type with capston heads, chromium plated screwed down high pressure, with or without letters Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipes and fixed all as specified and directed.

S&F in replacement 75mm bore PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F in replacement PVC (SWR) bend any radius 110mm complete all as specified and directed.

S & F in replacement Vitreous china squatting pan of Orissa patten size 580 x 440 white colour including CI S/P trap long size as directed joint run and lead front or back inlet with integral footrest including connection to trap and to flushing pipe,anti-syphonage pipe, etc, fixed in replacement complete and making good to floor in PCC 1:2:4 all as directed and specified.

S & F in replacement Vitreous china premium/1st quality urinal half stall type, white colour, of size 465x355x265 mm incl providing and fixing plugs/brackets, bedding urinal against wall in CM 1:2, securing urinals to plugs with and incl S&F of all accessories for fixing as recommended by manufacturer like 60mm long brass secrewS&Fasteners/rag bolts etc, pointing urinal back in white cement; connecting for discharge pipe incl necessary packing, union complete all as specified.

S&F in replacement Urinal spreader of PTMT any colour for fixing with 15mm dia pipe. (Minimum weight 60gms).

S&F in replacement PVC connection 15mm bore length not less than 450 mm long with both ends PTMT nuts complete all as specified.

S&F in replacement tubular towel rail, brass cromium plated, 20mm dia, D type, 60cm long between flanges complete all as specified and directed Engrs-In Charge.

S&F Non-Skid ceramic Coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:4 complete all as specified.

S&F Non Skid Ceramic tiles 8 mm thick in light shed ,area of each tiles exc 0.18 sqm but not exc 0.36 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:4, complete all as specified and directed

M&L 100mm thick cement concrete type D-2, 1:4:8 (40mm graded crushed stone aggregate) finishing cement concrete surface even and smooth without using extra cement as specified and directed.

M&L for 75mm thick plain cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection finished even and smooth without using extra cement, including making joints to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:2 by weight complete all as specified and as directed.

Demolition of cement concrete ( unreinforced) in roofs , floors (other than ground floors) beams, staircases,landing, chajjas and similar suspended work, removal of debris outside of MOD land, complete all as specified and as directed.

M&L plain cement concrete 1:2:4 type B1 using 12.5 mm graded aggregate as in roof for maint. the uniform slope etc any thickness at any height and in any position all as specified and directed by Engr-in-charge at site.

M&L Applying evenly a coat of bituminous primer confirming to IS 3384 - 1986 @ 0.40 Kg/Sqm, complete all as specified and as directed.

M&L APP based polymeric membrane minimum weight 3 Kg/Sqm and minimum 3 mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/sqm) land on primed surface by forced application as per manufacturer instruction, complete all as specified and as directed.

M&L Cement concrete tiles 20cm x 20xm x20mm thick, machine pressed; set, jointed and pointed in net cement shurry with grey cement and no pigment in Roof,(Over 15 mm thick Screed bed CM 1:6) and cut and polished all as specified.

S&F for stairs (framed) including stringers, treades, landing, balusters, hand rails etc, including cleats, brackets etc conf to Fe-410-w or E -250 quality A complete all as specified and directed.

M&L applying two coats of synthetic enamel paints on new steel surfaces over a coat of red oxide primer including surface preparation complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth,for foundation,laying of sewar line etc., and getting out in any type of soil complete all as specified and as directed.

Excavation over areas, n exc 1.5 m deep and getting out in any type of soil complete all as specified and directed

Excavation over areas, exc 1.5 m and n exc 3 m depth and getting out in any type of soil complete all as specified and directed

Returning, filling in, including spreading, leveling, watering and well ramming in layer not exceeding 25cm thick in any type of soil complete all as specified and as directed .

Removal of excavated soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and as directed .

Demolition and breaking up drain pipes (Salt glazed ware, AC or reinforced concrete) of any dia, set in cement mortar including PCC in bed and haunching against side including removing debris and rubbish outside MD land complete all as specified and as directed.

S & F 150 mm bore Reinforced cement concrete pipes, with collars, class NP2, laid in trenches and jointed complete all as specified and as directed .

M&L PCC 1:4:8 type D-2 by using 40 mm graded crused stone aggregate as in bed to 150 mm bore salt glazed stone ware drain pipe or reinforced concrete drain pipes, including packing under and haunching against the side of pipe after they are laid and tested complete all as specified and as directed .

Demolition of stone / boulder masonry walling built in cement mortar including all quoins arches pillars etc and removal unserviceable materials, debris, rubbish to out side MD land complete all as specified and as directed.

M&L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM (1:4) complete all as specified as directed.

Extra over stone walling for hammer dressing to face granite or trap stones with maximum depression on face from a straight edge held against the dressed surface not exceeding 20mm and dressing face beds and joints as specified of random rubble walling un-coursed or brought upto courses complete all as specified and as directed .

M&L PCC (1:2:4) type B-1 (using 20mm graded stone aggregates) as in coping,benching/channels of manholes including demolition of existing pcc etc complete all as specified and directed

M&L rendering 15mm thick in CM 1:4 on stone masonry surfaces, finished even and fair without using extra cement mixed with water proofing compound as per manufacturer instructions complete all as specified and directed. Note :- WPC will be measured and paid seperately.

M&L for RCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in precast manhole/drain covers including demolition of RCC slab, manhole/drain cover in any position complete all as specified and as directed.

S & F in replacement of stack clamps made out of 50 X 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 110mm bore pipes complete all as specified and as directed.

S & F in replacement of 110 mm bore PVC [SWR] vent cowl complete all as specified and as directed.

Demolition of reinforced cement concrete on roofs,floors ( other than ground floors), beams,staircase,landing, chajjas and similar suspended work complete all as specified and directed

M&L form work to soffits of suspended slabs such as roof slab landings and similar works n exc 100mm thick (horizontal or slopping) fair finished surfaces of concrete flat all as specified

M&L form work to edges of concrete flates ,treads break in floors ,window cills ,concrete railings , openings in concrete walls, floor and roofs n exc 20 cm wide and sisides of RCC/PCC bands in walls, horizontal or sloping and ssimilar work exc 10 cm but n. exc 20 cm wide rough finished surface of concrete

M&L Nominal mix reinforced cement concrete type B1 (1:2:4) using 20 mm graeded stone aggregate as in roof slabs supported on walls surfaces of concrete flat all as specified.

M&L HYSD TMT bars 10 mm and over cut to length, bent to shape required incl cranking, bending spirally for hoping for columns hooking ends and bindind with ms wire (annealed) not less than 0.9mm dia quality confirming to (GRADE FE-410-W,Gde.E-250 quality-A ), complete all as specified & as directed.

M&L for HYSD steel TMT bars but 8mm dia and over upto and including 8mm dia in stirrups, spacers and binders, complete all as specified & as directed.

M&L for Formwork for flat finished surfaces to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter all as specified and directed.

M&L for M-25 Cement concrete ( Nominal mix) Foundations, includingrafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete all as specified and directed.

M&L for Formwork for flat finished surfaces to sides of square, rectangular and polygon pillars,posts, struts, piers, columns and stanchions

M&L for Reinforced cement concrete (Nominal mix )M-25 in Columns, pillars, piers, posts and struts all as specified and directed.

M&L for Reinforced cement concrete (Nominal mix )M-25 in Beams, cantilevers, bressummers, lintels over 1.5m span all as specified and directed.

M&L for Formwork for flat finished surfaces to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

M&L for Reinforced cement concrete (Nominal mix )M-25 in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like all as specified and directed.

M&L for Treating the top surface of filled earth under the floors at the rate of 5 litres of emulsion per square metre of surface

M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area

M&L for 50mm thick cement concrete 1:2:4, type B-0 Damp proof course ( to horizontal or vertical surfaces including necessary formwork

M&L for applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m above DPC

M&L for precast-cement concrete block masonary with solid blocks type D-1 ,1:3:6 (20mm graded aggregates) exc 10 cm in width and setting in CM 1:4 ,complete all as specified and directed

Returning, filling in, including spreading, leveling, watering & well ramming in layer s not exc 25 cm in hard /dense soil.

Removing excavation material n. exe. 50m but n exc. 500m & deposited where directed at a level n exc. 1.5m above the starting point

M& L for rendering 5mm thick cement plaster in CM 1:3 on fair faces of brick/block work on concrete surfaces on ceiling including finished even and smooth all as specified and directed.

M&L for preperation of newly plastered surfaces of walls and applying two coats of oil bound distemper on ceiling surfaces over a coat of alkali resistant primer ocomplete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over 1mm thick birla white putty on plastered surface complete all as specified and directed.

M&L two coats of cement base paint over one coat of cement primer on walls including preparation of surfaces complete all as specified and directed.

M&L for Sand filling under floors or in foundations,in pinth height including watering and consolidation

M&L for PCC 75mm thick 1:4:8 type D2 using 40mm graded aggregate as in subbase

Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc. Complete.

M&L for glazed ceramic coloured tiles in verticle surface 350mmx450mmx7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over backing coat 10mm thick cement mortar in 1:4 complete all as specified and directed,

M&L for Kota stone slab 20-25mm thick in steps, skirting, dado and pillar partion for drawers laid over cement screed and jointed

M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor/ wall finishes in CM 1:6.

M&L for PCC 1:3:6 type C1 using 20mm graded aggregate as in filling of pressed steel frames for doors , bed blocks all as specified and directed

S & F Pressed steel frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified,

S&FFactory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and as directed.

S&F of 100mm long Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-22

Supply and fixing 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified

Supply and fixing 150 mm long aluminium, anodized barrel tower bolts of extruded section all as specified

Supply and fixing 150mm long extruded alluminium alloy handle, cast type, anodized all as specified

S&F in 4mm thick sheet glass, ordinary quality and glazing with oil putty /rubber beading in square not exceeding 0.50 Sqm in each pane including punching or drilling new glazing pins/spring clips complete all as specified and as directed.

S&F in replacement galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified and directed.

M&L 20mm bore dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F 20mm (OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/ walls and ceiling all as specified and as directed.

S&F 25mm (OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/ walls and ceiling all as specified and as directed.

S&F 25 mm outer dia gate valve/ ball valve for , screewd both ends for CPVC pipes and fixed complete all as specified and as directed

S&F of Grating round 140mm with waste hole made out of stainless steel complete all as specified and directed.

S&F in replacement 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls and ceilings complete all as specified and directed.

M & L for Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe complete all as specified and directed.

S & F in Vitreous China wash basin, white, flat back, size 630x450mm excluding ditto but including brackets complete all as specified and directed.

S&F 15mm fancy type bib tap, chromium plated with crutch or butterfly handle, screwed down , screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F tubular towel rail aluminium anodised 20mm dia 'D' type 60cm long between flanges complete all as sped & directed.

S&F in replacement 15mm dia concealed stop valve chromium fancy type , screwed down, high pressure , with crutch or butterfly handle , screwed both ends for iron pipe or for union complete all as specified and directed.

S& F Soap dish holder complete as specified and directed by Engr-in-Charge.

S&F vitreous china squatting pan "Orrisa Pattern" size 580x440mm white with integral foot rest(including flushing cistern) but including flush pipe, trap complete all as specified . Make : Cera/Hindware/Jaquar

S&F in replacement PVC connection 15mm size with PTMT nuts of length 450mm complete

S&F pillar taps fancy type cast copper alloy capston headed, chromium plated, screwed down, high pressure with long screwed shank and fly nut, screwed for 15mm bore iron pipe complete all as specified and directed.

S&F 15mm bore, stop/angle valve, cast copper alloy, fancy type chromium plated with long shank & cup (concealed type) screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipes complete all as specified and directed.

M&L for Jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted in complete all as specified and directed.

Surface excavation n.exc. 30 cm deep and averaging 15 deep and getting out in soft/loose soil.

Removing excavated material exc. 500m and n exc 1.5km and depositing where directed at a level above the starting point complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade and pigments including complete all as specified and directed.

M&L for 10 mm thick sand cushion with clean river sand duly clear of residual , organic and deleterious materials spread evenly to uniform thickness laid over DLC layer as complete all as specified and directed.

M & L cement concrete 1:4:8 of type E2 (using 40mm graded stone aggregate) as in filling and mass concrete complete all as specified.

M & L for Providing precast cement concrete type C1 1:3:6 (using 20mm graded stone aggregate) solid building blocks or slabs exc 10cm width (with plain or interlocking joints as directed) setting in Cement Mortar 1:6 in walls complete all as specified and directed.

M & L 15 mm thick rendering in cement mortar 1:6 on brick work or concrete surfaces on fair face , surface finished even and smooth without using extra cement complete all as specified.

M&L PCC 1:3:6 type C1 in copping and benching complete using 20mm graded crushed stone aggregate all as specified.

Removing excavated material n exc 50m and depoting where directed at a level n exc 1.5m above the starting point complete all as specified.

M&L providing precast cement concrete1:2:4 type B-1 in cover slabs (for manholes etc ) ,shelves and similar articles with plain faces set in cement mortar 1:6 complete all as specified.

M&L TMT bars 8mm dia cut to length, bent to shape required incl cranking, bending spirally for hoping for columns hooking ends and bindind with ms wire (annealed) not less than 0.9mm dia quality confirming to all as specified

M&LRungs -12mm dia cut to length, bent to shape required incl cranking, bending spirally for hoping for columns hooking ends and bindind with ms wire (annealed) not less than 0.9mm dia quality confirming to all as specified

M&L 150 mm Reinforced concrete pipes, class NP3, laid and jointed with one collar per length of pipe complete with collars complete all as specified.

M & L Concrete bed D-2 type 1:4:8, 150 mm thick to PCC bedding for RCC NP-3 pipe 150mm dia. including packing under, and hunching against the sides of pipes complete all as specified.

M&L For construction of septic tank 10 users as per TD No CEJZ/TD/31 Sheet No 1/3 to 3/3 dt 14.12.2013 designed to carry sewage and sullage water, excavation in any type of soil/ rock , PCC 1:4:8 below foundation, Vent shaft, connection etc., complete for For 10 User.

M&L Soakage wells excavation, in any type of soil/rock, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of stone masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete of 1.2 M dia X 3.0 M effective depth as per TD Drg No CEJZ/TD/29 sheet no 1/1 TO 3/3 dt 14.12.2013

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface in hard/dense soil.

M&L for Cement concrete Type C2 1:3:6 (40 mm graded aggregate) in foundations, filling and mass-concrete.

S & F of mild steel works posts & struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or reveting, etc., & similar work conforming to Fe 290 or E-165 complete all as specified and directed.

S&F MS round bars 10mm dia & above cut to length bent to shape required including cranking bending spirally for hopping for column hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality confirming to IS.Round bars 10mm dia

Supply only chain link galvanised iron fencing, any size or type. Note:- Weight of chain-link will be determinated through BOO constituted by GE.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire

S&F mild steel screw bolts (machine made) with hexagonal or square head and one end screwed or screwed both ends, each screwed ends to be fitted with washers and one hexagonal or square nut, exc. 10 cm but not exc. 15 cm long of 11 to 15 mm dia of shank.

Taking down old, unsv aluminium/copper point wiring (light, fan, socket or power) complete, incl fixture & fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit & making good the disturbed surfaces of walls, floors, etc. complete all as specified and directed by Engr-in-Charge.

Disconnecting/dismantling of old existing un serviceable DB's along with metal enclosue concealed in walls of any type/way 240/415 Volts with their old/un serviceable burnt MCCB/MCB's etc.incl making good the disturbed surfaces and matching with existing surfces complete all as specified and directed by Engr-in-Charge.

M & L for concealed point wiring with two single core 1.5 sqmm PVC insulated, unsheathed, FRLS cable, 1100 volts grade, ISI marked with multi stranded copper conductor drawn through and including non-metallic PVC rigid conduit (medium grade) with all fittings and accessories ISI marked incl provision of 1.5 sqmm PVC insulated, multistranded, unsheathed, copper conductor cable, FRLS, ISI marked as earth continuity conductor (green in colour) & incl fixing of modular metal flush boxes of appropriate size & thickness fixed flush to wall for mounting switch, sockets etc. with including cutting chases for conduits & sinkings for modular boxes & making good the disturbed surfaces, matching to the existing one etc., suitable for (a) One Light/fan/Call Bell etc. point controlled by one switch 5/6 Amps, complete all as specified & as directed.

All as per Item No. 209.00 here-in-above but suitable for one switch socket outlet point 5/6 Amps on Same board.

All as per Item No. 209.00 here-in-above but suitable for one switch socket outlet point 5/6 Amps on independent board.

All as per Item No. 209.00 here-in-above but with FRLS PVC insulated copper conductor cable of size 2.5 Sqmm and 2.5 Sqmm for earth continuity conductor green in colour for 16A switch socket complete.

S & F Modular switch, one way, 6 Amp, 1 Module, 240 volt complete all as specified and as directed. Make :- Verona model of CRABTREE (Havells) or techno-commercially equivalent in Legrand/Anchor Roma

S & F Modular switch with indicator, one way, 16 Amp, 1 Module, 240 volt complete all as specified and as directed. Make :- Verona model of CRABTREE (Havells) or techno-commercially equivalent in Legrand/Anchor Roma

S & F Modular shuttered socket outlet 3 Pin, 6/16 Amp, 2 Module, 240 volts, ISI marked complete all as specified and as directed. Make :- Verona model of CRABTREE (Havells) or techno-commercially equivalent in Legrand/Anchor Roma

Supply & Fixing and concealing modular metal flush box suitable for fixing switches/sockets of 1/2 modules all as directed. Make :- Verona model of CRABTREE (Havells) or techno-commercially equivalent in Legrand/Anchor Roma

Supply & Fixing modular cover plate suitable for fixing switches/sockets of 1/2 modules all as directed. Make :- Verona model of CRABTREE (Havells) or techno-commercially equivalent in Legrand/Anchor Roma

S&F ceiling rose surface PVC/ Polycarbonate, Isolated body with face Bakelite three terminal complete all as specified and directed.

Supply, install, testing & commissioning of Exhaust fan, PVC body with automatic back shutter louvers 250 mm sweep, 1280 RPM or more, Air Delivery not less than 860 CMH, single phase, 240 Volts, AC, 50 Hz and connecting up complete including louvers and provision of cable of suitable sizefrom ceiling rose to fan in flexible hose including taking down of old fan and making of suitable sized hole in the wall for fixing of the exhaust fan & making good the disturbed surfaces (if any) complete all as specified & as directed. Note :- (i) The cost of making hole in walls/other surfaces & making good the dsturbed surfaces incl any framework/cement work/wood work/welding work etc. required for proper fixing of the exhaust fan & matching to the existing surface is deemed to be included in the unit quoted rates

S & F and concealing SPN DB, 08 Way, IP43, IK09, Metal double door type 240 volts fitted with busbar and blanking plates, neutral link and making good the disturbed surfaces with all other accessories including necessary connection all as specified and directed by Engr-in-Charge.

S&F Miniature circuit Breakers, SPN,C-Series 240 Volts of capacity 6-32 Amps with breaking capacity 10 KA all as specified and dircted by Engr-in-Charge.

S&F Miniature circuit Breakers, single pole,C-Series 240 Volts of capacity (6-32 Amps) as ordered with breaking capacity 10 KA all as specified and dircted by Engr-in-Charge.

Supply, Fix, Installing and Testing Vertical type Storage electric water heater (Geyser) of 25 Ltrs capacity, Tank made of ultra thick super cold rolled steel plates with high density PUF insulation, 2 KW, 230 V, Single Phase, 50 Hz, AC, BEE 5 Star rated, suitable for a pressure rating of 0.8 MPa Bar with 7 years warranty on inner tank, 4 years on heating element & 2 year comprehensive warranty with & including connected accessories and 2 Nos anchor fasteners of size as per manufacturer instructions grouting and fixing and making good the disturbed surface complete and connecting electrical and water supply connection using steel braided hose 2 Nos complete all as specified and directed by the Engr-in-Charge. Note : (i) Installed Geyser's warranty card should be submitted to the Engr-in-Charge. (ii)The cost of making good the disturbed surfaces and matching to the existing/original surface is deemed to be included in the unit quoted rates

Taking down old sub-main wiring incl fixture & fittings etc. removing materials to store for keeping in safe custody or for taking credit & making good the disturbed surfaces of walls, floors, etc. complete all as specified and directed by Engr-in-Charge.

M & L for concealed sub-main wiring alongwith earth wire of size (2 x 4.00) sq. mm + (1 x 4.00) sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including non-metallic PVC conduit (medium grade) with all fittings and accessories ISI marked for conduits & sinkings for modular boxes & making good to walls, floors,ceiling etc. complete all as specified & as directed. .NOTE : 1) Two runs of PVC wire, one run of earth wire & one run of PVC rigid conduit (medium grade) will be measured as one length. 2) Modular metal flush boxes (if req) shall be measured & paid separately.2) Cutting chases & making good, including necessary Putty work of the disturbed surfaces is deemed to be included in the unit quoted rates.

S & F Modular shuttered socket outlet 3 Pin, 6 Amp, 2 Module, 240 volts, ISI marked complete all as specified and as directed.

Supply & Fixing and concealing modular metal flush box suitable for fixing switches/sockets of 3 modules all as directed.

Supply & Fixing and concealing modular metal flush box suitable for fixing switches/sockets of 12 modules all as directed.

Supply & Fixing modular cover plate suitable for fixing switches/sockets of 3 modules all as directed.

Supply & Fixing modular cover plate suitable for fixing switches/sockets of 12 modules all as directed.

S&F IP>=20, Class I Wall mounted 4 feet LED batten with integrated electronic driver & Aluminium body complete with all accessories, prewired, including 20 W with min 120 lumens/Watt output,6500 K, LED 4 feet tube light and connecting of flexible wire twin core from ceiling rose to fitting through & including flexible conduit from ceiling rose to fitting complete incl taking down old/unsv fittings all as specified and directed by Engr-in-Charge.

S&F IP>=20, Class I Wall mounted 2 feet LED batten with integrated electronic driver & Aluminium body complete with all accessories, prewired, including 10 W with min 120 lumens/Watt output,6500 K, LED 2 feet tube light and connecting of flexible wire twin core from ceiling rose to fitting through & including flexible conduit from ceiling rose to fitting complete incl taking down old/unsv fittings all as specified and directed by Engr-in-Charge.

S&F IP >= 65,IK>=07, Class I Environment friendly, energy saving, surface mounted, decorative bulk head edge lit LED luminaire 10W with min 120 lumens/watt output made of pressure die cast aluminium housing with suitable fixing arrangement complete with all accessories internally prewired and including connecting up with and including twin core twisted flexible copper conductor cable of suitable size complete incl taking down old/unsv fittings all as specified and directed by Engr-in-Charge.

S&F IP >= 65, IK>=07, Class I energy saving and environment friendly long life high power LED as source of building security light of 30W with min 110 Lumens/Watts, made up of pressure die cast aluminum housing with acrylic cover as diffuser with including GI pipe bracket made out of 40mm dia light grade pipe of length 1.2 Mtrs, bend to shape 120-130 degree and MS clamps made out of 25x3mm flat iron 2 Nos including nut and bolts for fixing the bracket and making connections through & including flexible conduit from ceiling rose to fitting complete incl taking down old/unsv fittings all as specified and directed by Engr-in-Charge.

Supply, install, testing & commissioning of Exhaust fan, metal body with automatic back shutter louvers 300 mm sweep, 1400 RPM or more, Air Delivery not less than 1850 CMH, single phase, 240 Volts, AC, 50 Hz and connecting up complete including louvers and provision of cable 3/2 core of suitable size from ceiling rose to fan in flexible hose and making of suitable sized hole in the wall/existing window/ventillator etc. for fixing of the exhaust fan & making good the disturbed surfaces (if any) complete all as specified & as directed. Note :- (i) The cost of making hole in walls/other surfaces & making good the disturbed surfaces incl any framework/cement work/wood work/welding work etc. required for proper fixing of the exhaust fan & matching to the existing surface is deemed to be included in the unit quoted rates.

Supply and Fixing ceiling fans complete with blades, down rods of suitable lengh upto Ceiling/false ceiling level, with fan regulator 2M and accessories, 230 V, 1200mm sweep, min air delivery 210 CFM with service value 6.00 BEE Five star rating with Brushless direct current rating (BLDC) including connecting up with and including twin/three core twisted flexible copper conductor cable of suitable size complete all as specified and directed by the Engr-in-Charge incl taking down old/unsv fan. Note : (i) Installed Ceiling fan's warranty card should be submitted to the Engr-in-Charge. (ii)The cost of making good the disturbed surfaces and matching to the existing/original surface is deemed to be included in the unit quoted rates (iii)The cost of taking down old unserviable Ceiling fan's and tranportation of old Ceiling fan's to be submitted to MES Store yard is deemed to be included in the quoted rate.

S & Fand concealing SPN DB, 04 Way, IP43, IK09, Metal double door type 240 volts fitted with busbar and blanking plates, neutral link and making good the disturbed surfaces with all other accessories including necessary connection all as specified and directed by Engr-in-Charge.

S & F and concealing SPN DB, 08 Way, IP43, IK09, Metal double door type 240 volts fitted with busbar and blanking plates, neutral link and making good the disturbed surfaces with all other accessories including necessary connection all as specified and directed by Engr-in-Charge.

Material and Labour for Taking down the Existing SPN Double door 8-Way DB Alongwith MCB, Disconnecting Electrical connection, Refixing and concealing the existing DB at Same and different location, including necessary connection all as specified and directed by Engr-in-Charge.Note for Item No. 24 to 26 :-The cost of making good the disturbed surfaces and matching to the existing/original surface is deemed to be included in the unit quoted rates

S&F Miniature circuit Breakers, SPN,C-Series 240 Volts of capacity 6-32 Amps with breaking capacity 10 KA all as specified and dircted by Engr-in-Charge.

S&F Miniature circuit Breakers, single pole,C-Series 240 Volts of capacity (6-32 Amps) as ordered with breaking capacity 10 KA all as specified and dircted by Engr-in-Charge.

Supply, laying, jointing & testing XLPE insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4.0 core in trenches / through GI pipe / fixed along with pole structure etc with all fixing & connecting accessories like Lugs, Gland etc incl taking down old existing Cable of any size/type complete all as specified & as directed.

Supply and laying light grade GI Pipe (ISI Marked) of 40mm dia for cable protection to be fixed on wall/in trenches with necessary clamps or in road crossing,complete all as directed(Rate qouted shall include MS clamps of required size wherever pipes are to be fixed on walls/other surfaces).

Supply and laying High density Poly-Ethylene Pipes(HDPE) of pressure rating 6Kgf/cm2 (ISI Marked) of 40mm dia for cable protection to be fixed on wall/in trenches/Ground with necessary clamps or in road crossing,complete all as directed(Rate qouted shall include MS clamps of required size wherever pipes are to be fixed on walls/other surfaces).

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for taking out/laying of UG Cables, GI Pipe etc. and getting out in Hard/Dense soil complete.

Supply and spreading Tibba Sand including watering and consolidation in trenches for cushioning/cable protection all as specified and directed by Engr-in-Charge. Note : Punned thickness shall be measured and paid

Supply and laying un-reinforced precast concrete cable cover, class LV, type 1, flat size 250 mm x 150 mm x 40 mm and abutting each other with gap between adjacent precast concrete cable cover not exceeding 10 mm over underground cables in trenches for cable protection of U/G cables with width equal to length of bricks complete all as specified and directed

M & L for cutting the existing hard standing /PCC /WBM road at a depth not less than 45 cm and 25 cm in width for passing of cable through GI pipe, returning filling in, complete including finishing the surfaces by providing top not less than 25 cm thick cement concrete type C-1 (1:3:6) using 20 mm grade aggregate, bottom filled with excavated earth and finishing to a uniform smooth surface complete all as specified and directed.

Supply, install, testing & commissioning of LT busbar junction box "out-door type" of size 600 mm (height) x 600 mm (breadth) x 300 mm (depth) (minimum dimensions), factory fabricated CPRI approved (type-tested) with suitable neoprene rubber gasket to make it completely dust & vermin proof & degree of protection not less than IP-55 & general construction confirming to IS-13947, double door, front & back openable. The box shall be provided with ventilation facility in the form of louvers for better heat dissipation & high grade Copper bus-bar of Size 300mm x 70mm x 6mm , min spacing of 75mm between the busbars & wrapped with coloured PVC tape /sleeves of rating in conformity to the Incoming cable rating. The panel board shall be fabricated out of 3.15 mm thick (for outer portions) & 2.00 mm thick (for inner portions) CRCA sheet duly pre-treated & powder coated, supporting angle iron frame of size 50X50X6mm fixed at 75 cm height from groud level & MC channel base suitable for 3 Phase, 4 wire system 415 /440 volts grade including I/C & O/G cable opening on bottom & at both sides including cable glands of suitable sizes with suitable PCC (1:3:6) type C-2 foundation , necessary earthwork (if any) incl Incoming MCCB of 63 Amps in seprate portion complete all as specified & as directed.

Supply, install, testing & commissioning of LT control panel board "out-door type" of size 900 mm (height) x 900 mm (breadth) x 300 mm (depth) (minimum dimensions), factory fabricated CPRI approved (type-tested) with suitable neoprene rubber gasket to make it completely dust & vermin proof & degree of protection not less than IP-55 & general construction confirming to IS-13947, double door, front & back openable. The panel shall be provided with ventilation facility in the form of louvers for better heat dissipation & high grade Copper bus-bar wrapped with coloured PVC tape /sleeves of rating in conformity to the Incoming ACB/MCCB rating. The panel board shall be fabricated out of 3.15 mm thick (for outer portions) & 2.00 mm thick (for inner portions) CRCA sheet duly pre-treated & powder coated, supporting angle iron frame of size 50X50X6mm fixed at 75 cm height from groud level & MC channel base suitable for 3 Phase, 4 wire system 415 /440 volts grade including complete internal wiring with not less than 2.5 Sqmm copper wire including cable glands and lugs of suitable sizes with suitable PCC (1:3:6) type C-2 foundation , necessary earthwork (if any) complete all as specified & as directed with & including the following accessories : (i) BUS-BAR & INTERNAL CONNECTIONS :- The bus-bars shall be made up of 04 Nos high grade Copper with rating should be suitable as per incoming Breaker, duly insulated with 1100 Volts grade standard colour coded PVC sleeves & rigidly mounted on suitable sized "F" class insulators of non-hygroscopic, non-combustible, all internal connections from main bus-bars to switch gears etc. PROVISION FOR CABLE ENTRY :- The provision for cable entry /exit shall be provided in the bottom for both incoming & out-going cables with the help of glands matching the existing LT cable sizes. INCOMING : (a) MCCB 4 Pole with thermal magnetic release, adjustable short circuit & adjustable overload setting, suitable for isolation, having breaking capacity 25 KA & of rating 63 to 80 A - 01 Nos.

Outgoing:- (a) MCB TPN "C" series having breaking capacity 10 KA of rating 40 to 63 Amps - 04 No.

M&L for Pre cast cement concrete Masonary with solid block (1:2:4) type B1 (using 20 mm graded stone aggregate) in plinth courses and throating incl 15 mm thick rendering complete all as specified & as directed by Engr-In-Charge.

Supply, install, testing & commissioning of CI Non-Return Butter fly Valve 40 mm bore, both end flanged, class PN 1.6, ISI marked conforming to IS 5312 (Part I & II) including making new flanged joints in existing 40 mm GI Pipe with rubber gasket, necessary bolts, nuts, washers etc of suitable size complete all as specified and to the entire satisfaction of the Eng-in-Charge.

M&L for galvanised steel water tubing, medium grade, 25mm bore with all running fittings such as bends, tees, unionss, elbows, connecting pieces etc. laid in trenches or on ground/other surface/PCC Block etc. incl testing complete all as specified and to the entire satisfaction of the Eng-in-Charge.

S&F Gun metal gate/globe valve 50 mm bore conforming to IS 781 -1984 with iron wheel head screwed both ends for iron pipe incl testing testing & taking down old unsv one complete all as specified and to the entire satisfaction of the Eng-in-Charge.

S&F Gun metal gate/globe valve 25 mm bore conforming to IS 781 -1984 with iron wheel head screwed both ends for iron pipe incl testing testing & complete all as specified and to the entire satisfaction of the Eng-in-Charge.

Supply, install, testing & commissioning of Foot Valve with GM working parts 50 mm bore, ISI marked conforming to IS 4038 including making new flanged joints with rubber gaskets, necessary bolts, nuts, washers etc. of suitable size incl taking down old unsv one complete all as specified and to the entire satisfaction of the Eng-in-Charge.

Supply and fixing energy efficient Lithium based Energy Efficient Integrated Solar Street Light of 12Watt, including Galvanised steel pole in built, Lithium ion battery, solar panel, charge controller with dusk down sensor complete including necessary excavation and suitable pcc foundation for Steel pole complete all as specified and directed by Engr-in-charge

S & F Modular shuttered socket outlet 3 Pin, 6 Amp, 2 Module, 240 volts, ISI marked complete all as specified and as directed. Cat No : ACVKSWW063, Model - Verona of make CRABTREE (Havells) or techno-commercially equivalent in Legrand/Anchor Roma

Supply & Fixing and concealing modular metal flush box suitable for fixing switches/sockets of 3 modules all as directed. Cat No : ACTXMIIX03, Model - Verona of make CRABTREE (Havells) or techno-commercially equivalent in Legrand/Anchor Roma

Supply & Fixing and concealing modular metal flush box suitable for fixing switches/sockets of 4 modules all as directed. Cat No : ACTXMIIX04, Model - Verona of make CRABTREE (Havells) or techno-commercially equivalent in Legrand/Anchor Roma

Supply & Fixing and concealing modular metal flush box suitable for fixing switches/sockets of 8 modules all as directed. Cat No : ACTXMIIX08, Model - Verona of make CRABTREE (Havells) or techno-commercially equivalent in Legrand/Anchor/ Roma

Supply & Fixing modular cover plate suitable for fixing switches/sockets of 3 modules all as directed. Cat No : ACVPPCWV03, Model - Verona of make CRABTREE (Havells) or techno-commercially equivalent in Legrand/Anchor Roma

Supply & Fixing modular cover plate suitable for fixing switches/sockets of 4 modules all as directed. Cat No : ACVPPCWV04, Model - Verona of make CRABTREE (Havells) or techno-commercially equivalent in Legrand/Anchor Roma

Supply & Fixing modular cover plate suitable for fixing switches/sockets of 8 modules all as directed. Make:- CRABTREE (Havells) Cat No : ACVPPCWV08, Model - Verona or techno-commercially equivalent in Legrand/Anchor Roma

S&F Surface and wall mounted LED batten 20 watts 4 feet long, extruded aluminium housing and polycarbonate diffuser provided for efficient heat dissipation & integrated electronic driver including connecting up with and including twin/three core twisted flexible cable of suitable size in flexible conduit all as specified and as directed . Make :Havells, Cat No:LUMILINEPLUSNEOBS20WLED865SPCSSIND or techno-commercially equivalent in Wipro/Philips

S&F Surface and wall mounted LED batten 10 watts 2 feet long, extruded aluminium housing and polycarbonate diffuser provided for efficient heat dissipation & integrated electronic driver including connecting up with and including twin/three core twisted flexible cable of suitable size in flexible conduit all as specified and as directed . Make :Havells, Cat No:LUMILINE+BS10WLED865SPCSS or techno-commercially equivalent in Wipro/Philips

Supply and fix energy saving high power LED building security light of 30W made up of pressure die cast aluminum housing with embedded PC cover having TOP Opening seperate driver compartment with IP66 protection including 40mm dia bracket bended into 120 degree angle and making connections in flexible conduit all as directed. Make: Havells,Cat no ENDURASUNDOWNSL30WLED757PASYBOPC Endura Sun Down of Havells or techno-commercially equivalent in Wipro/Philips

Supply and fix Environment friendly, energy saving, surface mounted, decorative bulk head edge lit LED luminaire 10W or min 1000 lumens with IP 66 with suitable fixing arrangement complete with all accessories internally prewired and including connecting up with and including twin core twisted flexible copper conductor cable of suitable size in flexible conduit all as specified and as directed . Make: Havells, Cat no HEXAFT10WLED857SSYMBOPC or techno-commercially equivalent in Philips/Wipro

Imp Note for :item No. 270) Design/Drawing/Technical catalogue/specifications along with comparative Rate Analysis to be submitted to the Engr-In-Charge/GE for Make/Sample approval of items whereever equivalency of Item(s) is concerned other than specified Make/Model/Cat/Part Ref concerned before placing order to the Manufacturer/Supplier. 2) Anything missed out in the technical specifications but technically required for efficient working is deemed to be included in the quoted rates.

Supply, install, commissioning & testing of Exhaust fan, metal body with automatic back shutter louvers 300 mm sweep, 1400 RPM or more, Air Delivery not less than 1850 CMH, single phase, 240 Volts, AC, 50 Hz and connecting up complete including louvers and provision of cable 3/2 core of suitable size from ceiling rose to fan in flexible hose and making of suitable sized hole in the wall/existing window/ventillator/other surfaces etc. for fixing of the exhaust fan & making good the disturbed surfaces (if any) complete all as specified & as directed. Make : Havells, Cat No: Ventil Air - DB or techno-commercially equivalent in Usha/Crompton. Note :- (i) The cost of making hole in walls/other surfaces & making good the dsturbed surfaces incl any framework/cement work/wood work/welding work etc. required for proper fixing of the exhaust fan & matching to the existing surface is deemed to be included in the unit quoted rates

S & F MCB, TPN, 10KA, 415V, "C" curve, 63 A, ISI marked complete all as specified and as directed.Make : LK, Cat No : BB40630C or techno-commercially equivalent in Legrand/ABB

S & F and cocealing MCB, DB, TPN, 04 ways, DOUBLE DOOR, IP-43, Ik-09 with metal door, rated bus bars, earth bar, neutral links complete including blanking plates as required and fixed flush to wall/other surface complete all as specified and as directed. Make : LK, Cat No : DETPN004DDS or techno-commercially equivalent in Siemens/Legrand

Supply and laying in trenches/through pipes or bare in road crossings/ paths /drains /ducts /floors /along poles/ walls/ ceilings etc. Cable Under ground, Armoured, XLPE insulated with stranded aluminium conductor, 1100 Volts grade of cross sectional area, 4 Core 16 Sqmm incl connecting with suitable glands, lugs etc all as specified and directed by the Engr-in-Charge. Make: Havells/Gloster/Polycab.

Excavation in trenches not exc 1.5 m wide and not exc 1.5m depth for errecting of poles, Laying of cables and getting out in Loose/soft soil complete all as specified.

Supply and laying un-reinforced precast concrete cable cover, class LV, type 1, flat size 250 mm x 150 mm x 40 mm and abutting each other with gap between adjacent precast concrete cable cover not exceeding 10 mm over underground cables in trenches for cable protection of U/G cables with width equal to length of bricks complete all as specified and directed

M & L for cutting the existing hard standing /PCC /WBM road at a depth not less than 45 cm and 25 cm in width for passing of cable through GI pipe, returning filling in, complete including finishing the surfaces by providing top not less than 25 cm thick cement concrete type C-1 (1:3:6) using 20 mm grade aggregate, bottom filled with excavated earth and finishing to a uniform smooth surface complete all as specified and directed.

Supply and spreading Tibba Sand including watering and consolidation in trenches for cushioning/cable protection all as specified and directed by Engr-in-Charge. Note : Punned thickness shall be measured and paid

M&L for galvanised steel water tubing, medium grade, 20 mm bore with all running fittings such as bends, tees, unionss, elbows, connecting pieces etc. laid in trenches or on ground/other surface etc. incl testing complete all as specified and to the entire satisfaction of the Eng-in-Charge. MAKE : Tata/Jindal/Prakash.

S&F Gun metal gate/globe valve 20 mm bore conforming to IS 781 -1984 with iron wheel head screwed both ends for iron pipe incl testing testing & complete all as specified and to the entire satisfaction of the Eng-in-Charge.

M&L for making connection of GI pipe line from existing any size GI/CI/DI pipe line by cutting/ tapping/ drilling of bore of suitable size including clamps, bolts etc. and checking of flow complete all asspecified and directed by Engr-in-Charge. Note : Cost of making good the disturbed surfaces as per existing/original surface is deemed to be included in the unit quoted rates.

NOTE:- (i)- Quantities are clubbed in BOQ for three Jobs. Item's qty details as per Annexure on Sl. Pg. No. 48 to 52 of tender. (ii)- Modular metal flush boxes shall be measured & paid separately. (iii) Cutting chases & making good the disturbed surfaces is deemed to be included in the unit quoted rates.

National Rewinding Works (BID ID -3459786)

m/s jogaram sujaram (BID ID -3453673)