Combined Package of Work A Replacement of Five Nos 220kV Breakers at 400kV Talaguppa RS Work B Replacement of Two Nos 220kV Breakers at 220kV Balligavi RS Work C Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110kV Talaguppa Work D Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog

Karnataka Power Transmission Corporation Limited

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

TECHNO - COMMERCIAL SHEETS

NOTE* For detailed scope of the work please refer Bid Documents.

BIDDERS TO READ CAREFULLY

THE FOLLOWING DOCUMENTS [DULY SIGNED BY AUTHORISED PERSON, WHEREVER NECESSARY] ARE TO BE UPLOADED IN KPPP PORTAL AND BANK GUARANTEE TOWARDS EMD OVER AND ABOVE RS.10.00LAKH AS PER ANNEXURE-II OF THE BID DOCUMENT SHALL BE SENT IN ORIGINAL TO CHIEF ENGINEER ELECTY., Transmission (Operations) Zone, KPTCL, Hassan SO AS TO REACH THIS OFFICE AFTER THE LAST DATE OF SUBMISSION OF BID AND ON OR BEFORE THE DATE & TIME NOTIFIED FOR OPENING OF TECHNO COMMERCIAL BIDS FAILING WHICH THE BID WILL NOT BE OPENED. 1) NO DEVIATION CERTIFICATE (SCHEDULE-16). 2) EMD/BID SECURITY AS DETAILED IN CLAUSE NO. 13 of ITT. 3) BANK GUARANTEE TOWARDS BALANCE EMD/BID SECURITY issued either by a Nationalized/Scheduled Bank. (For the balance EMD above Rs. 10Lakhs ) (SCHEDULE-17) - as detailed in Clause No. 13 of ITT-The Bidder shall scan the Bank Guarantee towards EMD and upload the same in the prescribed format in the slot specified for “EMD and Tender Fee Payments” in the e-procurement portal to enable the owner for verification of EMD BG at the time of opening of Techno Commercial Bid, failing which the offer will be rejected 4) LETTER OF UNDERTAKING (SCHEDULE-18). 5) CONSORTIUM AGREEMENT (IF APPLICABLE-SCHEDULE-19). 6) POWER OF ATTORNEY (SCHEDULE-20). 7) ANY OTHER AGREEMENTS / UNDERTAKINGS /SELF DECLARATIONS SPECIFIED IN THE TENDER.

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

BID PROPOSAL SHEET

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Bidder's Name & Address alongwith GSTIN no. :

Bid Proposal Reference :

Person to be contacted :

E-Mail Address:

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

a) * We have uploaded bid as individual Bidder. (Indicate Name of the Individual Bidder)

b) * We have uploaded bid in Consortium with the following Bidders. (Key in Consortium) VOID

Name of the Consortium Partner Scope / Participation of each Consortium Partner

(* Fill-up whichever is applicable)

1 We, the undersigned Bidder, having read and examined in detail the specifications and all the Bidding documents of the said work and hereby propose to design, manufacture/fabricate, shop test, supply on FOR site basis, and carry out the erection, testing and commissioning including civil, structural and architectural works for

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

2 PRICES AND VALIDITY :

2.1 We declare that the Prices stated in our Proposal are in accordance with subject bid documents including Clause No.40 of "Conditions of Contract (CC)" and Clause No.11 of Instruction to Tenderers (ITT) of Bid Documents. We further declare that all Ex-works price/CIF components of Spares, Maintenance and Testing Equipments and other charges viz., Freight and Insurance, Type Test charges and other charges stated in our proposal shall be as per the Tender conditions. All the Price and other terms and conditions of this Proposal are valid during the Performance of the Contract.

2.2 All Taxes and Duties, such as Custom Duties on imports, Levies, Surcharge/Cess etc., if any, applicable on the transaction are included in the Bid Price and shall be to Our account and the Owner is not having any liability whatsoever on this account, whatever may be the contrary elsewhere in the Bid documents. However the component of Taxes & Duties included in the Bid Price are separately indicated in Schedule - 2 for TDS purpose. We further confirm that our Bid Prices as quoted in Schedule-I, include all import Duties and levies including Licence fees lawfully payable by us on imported items and all other Taxes, Duties and Levies applicable on Bought-out Components, Materials, Equipment and other items and confirm that any such Taxes, Duties and Levies additionally payable shall be to our account. We further confirm that no Sales Tax in any form shall be payable by Owner either for Bought-out items which are despatched by our Sub-Suppliers directly to the Project Site or for items Supplied directly by us.

2.3 We declare that we have noted and considered Clause No.39 of Conditions of Contract (CC ), Clause No. 11.11 of Instruction to Tenderers (ITT) of Bid Documents regarding Taxes and Duties and quoted our Prices accordingly. We further agree for TDS as per Statutory stipulations.

2.4 The Bid Prices, the Price components of the various items in the Scope of Supply, Erection including Testing & Commisisoning, Civil and Mandatory spares is quoted in Itemwise Financial Bid in KPPP Portal for this proposal..

3 CONSTRUCTION OF THE CONTRACT : We, declare that we are making the Offer on the basis of Single Contract for the entire Scope of the Package in accordance with Clause No.26 of Instruction to Tenderers (ITT) of Bid Document.

4 We having studied Clause No.39 of Conditions of Contract (CC ), Clause No. 11.11 Instruction to Tenderers (ITT) of Bid Documents , relating to Tax and we hereby, declare that if any income-tax, surcharge on income tax or any other corporate tax is attracted under the law, we agree to pay the same.

5 Bid Security/ EMD : We have enclosed a Bid Security through e-Payment mode for a sum of Rs.10.00Lakhs and remaining amount of Rs.................................................. ( above Rs.10 Lakhs) in the form of Bank Guarantee in original and two copies of the original valid for a period of 225 days from the date of opening of bids, and liable to be forfeited in accordance with Bid Documents. (Mode of Payment towards EMD is as detailed in NIT/CLAUSE NO. 13 of ITT.)

We have also ensured that the above Bid Guarantee furnished by us is in line with the Bid Documents and complete in respect of following :

1. Value of Non judicial Stamp Paper purchased in the name of executing Bank is as per Stamp Act.

2. Power of Attorney Number and Date as well as Signature and Full Name and Designation of Executant along with Bank's Stamp are there.

3. Signature, Full Name, Designation and address of Witness are there.

4. Completed Mailing address of the Head Office of the Bank is indicated.

6.1 We declare that the Works shall be performed strictly in accordance with the Specifications and Documents except for the variations and Deviations, all of which have been detailed out exhaustively in the following Schedules, irrespective of whatever has been stated to the contrary anywhere else in our Proposal.

a Commercial Deviations Schedule Schedule - 5

b Technical Deviations Schedule Schedule - 6

6.2 We further confirm that Specified Stipulation of following Clauses are acceptable to us and No Deviation / Exceptions are taken on any account whatsoever in the following Clauses.

a. Terms of payment Clause No. 37 of Conditions of Contract (CC) & Clause No.8 of Special Conditions of Contract-SCC.

b. EMD/Bid Security Clause No.6, Section :1, Invitation for Tenders (IFT) and Clause No.13, Section :2, Instruction to Tenderers (ITT)

c. Contract Performance Guarantee Clause No.29, Instruction to Tenderers (ITT)

d. Penalty for delay Clause No.41 of Section-5 : Conditions of Contract (CC)

e. Price Basis/ Price adjustment Clause No. 40 of Section-5 :Conditions of Contract (CC)

f. Defects Liability Period/Guarantee Clause No.10 of Special Conditions of Contract (SCC) and Section 6 : Contract data

g. Work Schedule Clause No.17 of Conditions of Contract-CC

h. Taxes and Duties Clause No.11.11 of Instruction to Tenderer (ITT)

Further, we agree that additional conditions, if any, found in the Proposal Documents other than those stated in Deviation Schedules, save that pertaining to any rebates offered, shall not be given effect to.

7 PERFORMANCE GUARANTEE ; We declare that the ratings and performance figures of the equipment to be supplied and erected by us are guaranteed. The Guaranteed particulas of different equiment in our Scope are enclosed in Data Requirement Sheets.

8 BID PRICING : We further, declare that the Prices stated in our Proposal are in accordance with your ITT & SCC and all other relevant clauses of Bid Documents.

9 PRICE ADJUSTMENT : We declare that the Prices quoted by us are in accordance Clause No. 40 of Section-5 :Conditions of Contract (CC)

10 SPECIAL TOOLS AND TACKLES : We have given a list of Special Tools and Tackles in Schedule - 7 and Prices thereof are included in our lumpsum Bid Price. We further agree that any items of Special Tools and Tackles, though not included in the aforesaid list, but required for effective Erection, Testing, Commissioning & Operation of the Equipments of Substations shall also be furnished by us, at no extra cost to you.

11 ADDITIONAL INFORMATION : In addition to the information called for in these Proposal Sheets, we have included with this Proposal, additional information as listed in Schedule - 8. We further confirm that such additional information does not imply any additional deviation beyond those covered in Schedule - 5 & 6 and in case of any contraction between these additional information and other provisions of Bid, the later will prevail.

12 QUALIFICATION DATA : We confirm having submitted the Qualification Data, as required by you in your Bid Documents in e-Procurement Portal along with this Proposal. Further we have filled in the information for Qualification Requirements in Schedule 9. In case you require any further information in this regard, We agree to furnish the same in time.

13 WORK SCHEDULE : If this Proposal is accepted by you, we agree to submit Engineering Data, Provide Services and complete the entire Work from time to time, in accordance with Schedules indicated in the Proposal. We fully understand that the Time Schedule stipulated in this Proposal is the essence of the Contract, if awarded. The completion schedule of the various Major Key Phases of the Work is indicated in Schedule - 11.

14 CONTRACT PERFORMANCE GUARANTEE ; We further agree that if our Proposal is accepted, we shall provide an irrecoverable Contract Performance Guarantee, of value equivalent to Five Percent (5%) of the Contract Price plus additional security for unbalanced tenders in accordance with Clause 25.5 & 29 of Instructions To Tenderers (ITT) and Clause No. 43 of the Conditions of Contract (CC) of the tender valid up to the end of ninety (90) days after the end of the Contract Warranty Period in the form of .........................................................................................................................................................................................................................................................(Please specify the form of Guarantee) in your favour and enter into a formal agreement with you within Twenty (20) days from the date of issue of Letter of Intent to award the Contract .

16 CHECK LIST : We have included a Checklist duly filled in Schedule 21

17 We, hereby, declare that only the Persons or Firms interested in this Proposal are named herein as Principals and that no other Persons are interested in the Proposal or in the Contract to be entered into, if we are awarded the Contract, and that this proposal is made without any connection with any other Person, Firm or Party likewise submitting a Proposal and that this Proposal is in all respect for and in good faith, without collusion or fraud.

18 We declare, in case our bid is accepted, that until a formal Contract is prepared & executed, this bid together with your written Letter of Intent to Award the Contract thereof and your notification of award /Letter of Intent to Award the Contract shall constitute a binding contract between us. We further understand that you are not bound to accept the lowest or any bid you may receive.

Thanking you, we remain,

Yours faithfully,

Place Printed Name

Business Address Country of Incorporation (State or Province to be indicated)

Name and Address Principal Officer

Karnataka Power Transmission Corporation Limited

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

FILL ONLY IN LIGHT BLUE COLOURED CELLS.

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

We declare that in terms of Clause no. 11 of ITT & all other relevant clause of Bid documents, the following are our lumpsum price in Rupees for the entire scope of work as specified in the Specifications and Documents.( Inclusive of all Taxes & Duties).

Total Lumpsum Price : ( In Figures) Note: Fill as "YES" against this column in case Prices are indicated in the percentage Wise Bid Financial Offer in figures

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE- 2 B - STATEMENT OF COMMERCIAL TERMS AND CONDITIONS

SHEET FOR TECHNOCOMMERCIAL OPENING

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Details of payments made in the form of Credit card/Debit card/NEFT/RTGS/OTC (over the counter) as per the tender conditions should be keyed in against column no. 3 (a) . BG Amount, BG No. and date, Name and address of the bank issuing the BG, validity of the BG should be keyed in against column no. 3 (b) .

FILL ONLY IN LIGHT BLUE COLOURED CELLS.

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

STATEMENT OF COMMERCIAL TERMS AND CONDITIONS

Sl. No. Particulars Details

1 Bid proposal form uploaded

2 No deviation certificate uploaded

3. a) EMD / Bid Security Bids shall be accompanied by bid security (EMD); 1) Up to Rs.10Lakh The following modes of payment will be provided as a part of e-Payment services. • Credit Card/Debit Card • Net Banking • NEFT/RTGS • Over-the-Counter (OTC) • IMPS For further detail regarding mode of e-payment of EMD in e-procurement platform, contact e-procurement cell, Government of Karnataka.

b) EMD amount above Rs.10Lakh by Bank Guarantee

4 Validity of the Bid.

5 Qualifying Requirements.

6 Financial capability

8 Taxes & Duties.

9 Completion Schedule

10 Defects Liability Period/Guarantee

11 Payment Terms

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 3A(i) - Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa.

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Bidder's Name & Address along with GSTIN no. :

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

BIDDERS SHALL FILL ONLY IN THE LIGHT BLUE COLOURED CELLS.

Sl. No. Name of the Equipment/Materials Unit Qty Rate Total qty

Work Order Nos: V-117 Dtd. 30.11.2022

1 PVC insulated 14 Core 2.5 Sqmm copper control cable with lugs/ferrules. Km 2.11 552000.00 1164720.00

2 PVC insulated 4 Core 6 Sqmm copper control cable with lugs/ferrules. km 3.00 247000.00 741000.00

3 Aluminium tube, Confirming to 6340WP of IS 5082,1969, BS1600 Sch 40 of Size 100mm(4"). Mtr 50.00 3505.00 175250.00

4 Total Supply Portion 2080970.00

PART B - Errection Portion

1 220KV Circuit Breaker Erection, assembly, alignment & interpole wiring of breakers with its connected equipments including movement from the point of unloading to the point of erection Set 5 27325.00 136625.00

A3 Grounding of Equipment with 75*8 mm G.I.Flat and connecting equipment to earthmat/ground pit. Each point of earthing with all formation works like bending, twisting, drilling of holes and connecting by welding(inclusive of all T&P and consumable)to the earthmat/ground pit/point of earth connection,all the material supplied by contractor. Rmtr 175 847.00 148225.00

A4 Laying of control cable from equipment to Control panel & Relay panel as per KPTCL Specification

1 14 Core 2.5 Sqmm copper control cable with lugs/ferrules Rmtr 2112.00 15.00 31680.00

2 4 Core 6.0 Sqmm copper control cable with lugs/ferrules Rmtr 3000.00 15.00 45000.00

A5 Total Errection Portion 361530.00

PART C - De-commissioning Portion

A6 Dismantling of existing Age old CGL make 245kV Pneumatic type SF6 Circuit Breakers along with mounting structure. (same as that of Erection Charges) Set 5 27325.00 136625.00

A7 Loading of released circuit breaker along with mounting structure at Talaguppa site , Each Breaker = 3.9 MT t 19.5 2061.00 40189.50

A8 Unloading of released circuit breaker along with mounting structure at KPTCL Major Works Divisional stores, Shimoga, Each Breaker = 3.9 MT t 19.5 2061.00 40189.50

A9 Transportation of released Circuit Breaker along with mounting structure using 11 to 20 MT Truck & Trailor from Talaguppa site to KPTCL Major Works Divisional stores for a minimum distance of 250Kms km 250 105.42 26355.00

A10 Total De-commissioning Portion 243359.00

A11 PART D - Testing & commissioning

1 Assisting in Testing & commissioning. Set 5 4632.00 23160.00

2 WIRING : Identification, Ferruling, crimping & termination of Wires in breaker & wiring up to relay panel & control panel. Set 5 11225.00 56125.00

3 Testing & Commissioning: Test for insulation level/IR value, gas leakage, testing for travel time (C, O & CO & OC), trip and close timings. Local trip close test, remote trip and close test, tripping through relays, operation of interlocks, contact resistance test etc., DCRM for 220 kV and above class Set 5 44222.00 221110.00

A12 Total Testing & commissioning Portion 300395.00

A13 Labour/Erection/Dismantling charges and Testing & Commissioning Charges (A5+A10+A12) 905284.00

PART E - Civil Portion

1 Earth work excavation by manual means for drains,canals, waste weir, draft, approach channels, key trenches, foundation of bridges and such simillar works in all kinds of soils, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work. In all kinds of soils Depth upto 1.5 m. Cum 69.35 242 16782.70

2 Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately) Mix 1:4:8( M5) Using 40 mm nominal size graded crushed coarse aggregates. Cum 4.1 5607 22988.70

3 Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) 2.2.1.1 M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (Footings) including Providing and removing centering, shuttering, strutting, propping etc., Cum 6.75 6369.52 42994.26

4 Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) 2.2.1.1 M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (Footings) including Providing and removing centering, shuttering, strutting, propping etc., 70% for Form work for columns (6287+70%) Cum 24 10512.8 252307.20

5 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. Cum 30.35 266 8073.10

6 Removal of Unserviceable Soil with Disposal upto a suitable distance as directed by the Engineer incharge of work. Cum 39.05 85 3319.25

7 Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification All other type of structures. kg 1303.2 69.74 90885.17

Total Civil Charges 437350.38

Basic Rate (Supply+Errection+ Civil) 3,423,604.38

Note: 1. Supply of equipment and materials shall include loading and unloading

2. The bidder shall quote same rates for common materials in all the schedules of the price sheet.

Place Designation

Name of the company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 3A(ii) - Tender schedule for Work-B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi.

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Bidder's Name & Address along with GSTIN no. :

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

BIDDERS SHALL FILL ONLY IN THE LIGHT BLUE COLOURED CELLS.

Sl. No. Name of the Equipment/Materials Unit Qty Rate Total qty

Work Order Nos: V-117 Dtd. 30.11.2022

1 PVC insulated 4 Core 6 Sqmm copper control cable with lugs/ferrules. km 0.15 247,000.00 37,050.00

1 Total Supply Portion 37050.00

PART B - Errection Portion

A2 220KV Circuit Breaker Erection, assembly, alignment & interpole wiring of breakers with its connected equipments including movement from the point of unloading to the point of erection Set 2 27,325.00 54,650.00

A3 Grounding of Equipment with 50*6 mm G.I.Flat and connecting equipment to earthmat/ground pit. Each point of earthing with all formation works like bending, twisting, drilling of holes and connecting by welding(inclusive of all T&P and consumable)to the earthmat/ground pit/point of earth connection,all the material supplied by contractor. Rmtr 60 335.00 20,100.00

A4 Laying of control cable from equipment to Control panel & Relay panel as per KPTCL Specification

4 Core 6.0 Sqmm copper control cable with lugs/ferrules Rmtr 150.00 15.00 2,250.00

A5 Total Errection Portion 77000.00

PART C - De-commissioning Portion

A6 Dismantling of existing Age old CGL make 245kV Pneumatic type SF6 Circuit Breakers along with mounting structure. (same as that of Erection Charges) Set 2 27,325.00 54,650.00

A7 Loading of released circuit breaker along with mounting structure at Talaguppa site , Each Breaker = 3.9 MT t 7.8 2,061.00 16,075.80

A8 Unloading of released circuit breaker along with mounting structure at KPTCL Major Works Divisional stores, Shimoga, Each Breaker = 3.9 MT t 7.8 2,061.00 16,075.80

A9 Transportation of released Circuit Breaker along with mounting structure using 10T Truck & Trailor from Balligavi site to KPTCL Major Works Divisional stores for a minimum distance of 250Kms km 250 81.99 20,497.50

A10 Total De-commissioning Portion 107299.10

A11 PART D - Testing & commissioning

1 Assisting in Testing & commissioning. Set 2 4,632.00 9,264.00

2 WIRING : Identification, Ferruling, crimping & termination of Wires in breaker & wiring up to relay panel & control panel. Set 2 11,225.00 22,450.00

3 Testing & Commissioning: Test for insulation level/IR value, gas leakage, testing for travel time (C, O & CO & OC), trip and close timings. Local trip close test, remote trip and close test, tripping through relays, operation of interlocks, contact resistance test etc., DCRM for 220 kV and above class Set 2 44,222.00 88,444.00

A12 Total Testing & commissioning Portion 120158.00

A13 Labour/Erection/Dismantling charges and Testing & Commissioning Charges (A5+A10+A12) 304457.10

PART E - Civil Portion

1 Earth work excavation by manual means for drains,canals, waste weir, draft, approach channels, key trenches, foundation of bridges and such simillar works in all kinds of soils, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work. In all kinds of soils Depth upto 1.5 m. Cum 27.74 242.00 6,713.08

2 Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately) Mix 1:4:8( M5) Using 40 mm nominal size graded crushed coarse aggregates. Cum 1.64 5,607.00 9,195.48

3 Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) 2.2.1.1 M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (Footings) including Providing and removing centering, shuttering, strutting, propping etc., Cum 2.7 6,369.52 17,197.70

4 Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) 2.2.1.1 M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (Footings) including Providing and removing centering, shuttering, strutting, propping etc., 70% for Form work for columns (6287+70%) Cum 9.6 10,512.80 100,922.88

5 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. Cum 12.14 266.00 3,229.24

6 Removal of Unserviceable Soil with Disposal upto a suitable distance as directed by the Engineer incharge of work. Cum 15.62 85.00 1,327.70

7 Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification All other type of structures. kg 521.28 69.74 36,354.07

Total Civil Charges 174940.15

Basic Rate (Supply+Errection+ Civil) 516,447.25

Note: 1. Supply of equipment and materials shall include loading and unloading

2. The bidder shall quote same rates for common materials in all the schedules of the price sheet.

Place Designation

Name of the company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 3A(iii) - Tender schedule for Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa.

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Bidder's Name & Address along with GSTIN no. :

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

BIDDERS SHALL FILL ONLY IN THE LIGHT BLUE COLOURED CELLS.

Sl. No. Name of the Equipment/Materials Unit Qty Rate Total qty

Work Order Nos: WO No.: Y-126/ 06.08.2024

A Material portion

1 11 kV, 400 Amps Special Roaster GOS set 1 14956.00 14956.00

2 9 kV, 10 kA Lightning Arrester (metal oxide type) Nos 6 1584.00 9504.00

3 11kV UG Cable 3coreX240sqmm (Running 1 Length of 110 Mtrs and other length of 20Mtrs cable) Km 0.13 1656048.00 215286.24

4 Heat Shrinkable termination kit for 11kV XLPE UG cable of size 3 core 240sqmm (Indoor) No 2 4691.00 9382.00

5 Heat Shrinkable termination kit for 11kV XLPE UG cable of size 3 core 240sqmm (Outdoor) No 2 5318.00 10636.00

Copper Control cables

6 a) 19 core X 2.5 sqmm (for control, protection, indication and annunciation) m 230 709.00 163070.00

7 b) 4 coreX 6 sqmm for AC and for DC supply (2x130Mtrs) m 260 247.00 64220.00

8 2 hole paddle suitable for Coyote ACSR conductor 610A Nos 6 2,250.00 13500.00

9 C Wedge connecctors suitable for Coyote ACSR conductor Nos 6 773.00 4638.00

10 Coyote ACSR Conductor m 15 164.00 2460.00

11 RCC Pole - 9 Mtr Long, 145 Kg WL Nos 2 7076.00 14152.00

12 Flexible copper earthing strip/bond having size of 450 mm long, 15 mm width and 3 mm thick both side lugs with nut and bolts Nos 4 563.00 2252.00

13 11 kV, Horizontal Cross Arm - Galvanised Iron (GI) Nos 1 487.00 487.00

14 DP Set (2 Pole Strucrure Kit) For RCC Pole - 9 Mtr Long, 145KG WL/PSCC Pole - 9 Mtr Long, 300Kg WL - GI Set 1 8863.00 8863.00

15 Rubber mats 1000 mm x 2000 mm x 12 mm size tested for 15 kV class Nos 3 1900.00 5700.00

16 Aluminum Lugs 185Sqmm Nos 12 39.00 468.00

17 Name plates Nos 6 333.00 1998.00

SCADA Materials 0.00

18 Multi functional Transducer(MFT) Nos 2 4875.00 9750.00

19 Channel opto coupler 110V Nos 1 1312.00 1312.00

20 Voltage cable & current cable : RYB & Black colour 4Core 2.5 Sqmm for MFT PI interfacing for feeder Rmtrs 60 25.00 1500.00

21 Signal cables Armoured copper core 0.5sqmm multistrand 10 cor (DI and MFT communication wiring) Rmtrs 160 143.00 22880.00

22 Control cables copper core 1.5sqmm multistrand 10core(DO and signal wiring) Rmtrs 25 155.00 3875.00

24 Link TB's Nos 16 50.00 800.00

25 Glands, Disc rail, screws, nuts and bolts, lugs, insulatio tape,tie L/S 1 2266.00 2266.00

Total Supply Portion 584555.24

B Labour portion

1 Erection of 11 kV MCVCB, 350 MVA, 25 kA, 1250 A incomer 800 A feeder (SCADA compatible) with 0.2S class 200-100/1-1 CTs Panel 2 2081.00 4162.00

2 Erection of Adapter panel for MCVCB 1250 A for connecting Megawin make switchgear to MEI make Switchgear Panel 1 2081.00 2081.00

3 Erection of Annunciator Panel for two feeders Panel 1 2081.00 2081.00

4 Wiring & assisting in Testing & Commissioning of 11 kV switchgear panel Panel 2 941.00 1882.00

5 Wiring & assisting in Testing & Commissioning of 11 kV annunciator panel Panel 1 941.00 941.00

6 Testing and commissioning of switchgear panel 2 28460.00 28460.00

7 Formation of Heat Shrinkable termination kit for 11kV XLPE UG cable of size 3 core 240sqmm (Indoor) No 2 3752.00 7504.00

8 Formation of Heat Shrinkable termination kit for 11kV XLPE UG cable of size 3 core 240sqmm (Outdoor) No 2 3752.00 7504.00

9 Supplying & Providing 450 mm dia 450 mm height 1.5" to 2" thick hume pipe collar (non pressure type) for earth pits including all lead and lifts etc., Nos 2 1499.00 2998.00

10 Grounding of equipments by providing cast iron pipe of 100 mm ID 13 mm thickness, 2.75 metres long with 2 part clamp out of G.I. Flat 50 X 6 mm continuously welded alround the pipe using cast iron welding electrodes as per drawing including the cost of excavation (All materials to be supplied by the contractor) Set 2 3491.00 6982.00

11 Grounding of equipment with 50 x 6 mm G. I. Flat and connecting Equipment to the earth mat/ ground pit. Each point of earthing with all formation works like bending, twisting, drilling of holes and connecting by welding (inclusive of all T&P and consumables) to the earth mat/ ground pit/ point of earth connection, all the materials supplied by the contractor. Rmtrs 100 335.00 33500.00

12 Formation of 11kV DP structre with 9 mtr. RCC pole Set 1 4134.00 4134.00

13 Mounting of 11 kV, 400 Amps Special Roaster GOS set 1 1214.00 1214.00

14 Mounting of H frame for fxing of GOS Nos 1 323.00 323.00

15 Erection of 9 kV, 10 kA Lightning Arrester (metal oxide type) (1 set= 3 Nos) set 2 119.00 238.00

16 Fixing of equipment name plates and earthing name plates Nos 6 83.00 498.00

17 Laying of Signal cables Armoured copper core 0.5sqmm multistrand 10 cor (DI and MFT communication wiring) Rmtrs 160 25.00 4000.00

18 Fixing of Channel opto coupler 110V Nos 1 1555.00 1555.00

19 Fixing of Multi functional Transducer(MFT) Nos 2 1555.00 3110.00

20 Configuration of RTU & Engineering alonf with validation of data at SLDC Nos 2 2381.00 4762.00

Total Errection Portion 117929.00

A Civil portion

1 Earth work excavation by manual means for drains,canals, waste weir, draft, approach channels, key trenches, foundation of bridges and such simillar works in all kinds of soils, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work. In all kinds of soils Depth upto 1.5 m. Cum 41.57 242.00 10059.94

2 Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately) Mix 1:4:8( M5) Using 40 mm nominal size graded crushed coarse aggregates Cum 4.6 5607.00 25792.20

3 Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) 2.2.1.1 M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (Footings) including Providing and removing centering, shuttering, strutting, propping etc., Cum 0.9 6369.52 5732.57

4 Providing and laying in position Reinforced cement concrete for all Substructures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necesary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) Mix 1:2:4 (M15) Using 20 mm nominal size graded crushed coarse aggregates Cum 2.92 6327.00 18474.84

5 Refilling available earth around trenches/pipelines, cables in layers not exceeding 20 cms in depth, compacting each deposited layer by ramming after watering with a lead upto 50 m , and lift upto 1.5 m. Including cost of all labour complete as per specifications Cum 18.14 122.00 2213.08

6 Disposal off the excess excavated earth of all types by vehicle including loading, unloading with all lead and lifts, labour, HOM of machineries etc. for: Upto 15 km Cum 23.43 312.00 7310.16

7 Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification All other type of structures kg 26 69.75 1813.50

8 Providing and fixing Structural Steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge. kg 1204 93.00 111972.00

9 Providing and laying to required line and slope roofing with corrugated asbestos cement sheet 6mm. thick fixed with galvanised iron J or L hooks, bolts and nuts 8mm. dia C.I plain and bitumen washers over the existing purlins, rafters and trusses including cost of materials, labour, complete as per specifications Sqmtr 63.92 332.00 21221.44

10 Providing and fixing ridges, hips with asbestos cement sheet roofing with G.I. J or L hooks, bolts and nuts 8mm. dia G.I.plain and bitumen washers, serrated or plain wings, adjustable ridges, including cost of materials, labour, complete as per specification m 3.5 299.00 1046.50

11 Providing PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joints, testing and commissioning, including loading unloading at both destinations and cuts of pipes wherever necessary including jointing of PVC pipes and specials (excluding cost of specials) with jointing of approved type, with all labour with all lead & lift including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excavation etc. complete and giving necessary hydraulic test to the required pressure as per ISS (Contractor will make his own arrangements for procuring water for testing) etc. complete For PVC pipes 75mm dia., 6 kg/sqcm & class 3 m 10 220.00 2200.00

12 PVC pipes 110mm dia., 6 kg/sqcm & class 3 m 10 411.00 4110.00

13 Jelly Spreading (20-25 mm) : Supplying and providing jelly in the station yard of uniform thickness of 100 mm including the cost of materials, labour charges, required tools and plants etc., complete. Work shall be carried out as per the instructions of Engineerin- charge of works as per the standard procedure Sqmtr 20 177.30 3546.00

14 Providing M-Sand : Supplying and filling in plinth, foundations / UG cable work with approved M-sand including watering, ramming, consolidating and dressing. The rate includes the cost of material, labour charges, required tools and plants etc., complete. Work shall be carried out as per the instructions of Engineer- in-charge of works as per the standard procedure. Cmtr 7.8 1965.00 15327.00

15 Providing and laying of Burnt Brick (Non – Modular) : Nos 1560 8.00 12480.00

16 Providing 20 mm cement plaster of mix :1:6 (1 cement: 6 fine sand) to brick/stone masonary including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge Sqm 16.9 331.00 5593.90

17 Supplying and wiring adopting loop system in existing PVC Conduit/ casing capping using 2x1.5Sqmm (Phase&Neutral) & 1x1.0sqmm (Earthwire )FRLS multistrand PVC insulated copperwire (confirmingtoIS-694: and latest amendments) with a 6Amps flush type SP control switch shall be fixed on the existing plastic sheet/gangbox, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet. Short point upto 3Mtr from tapping point to out let via switch points 2 285.00 570.00

18 Supplying and wiring adopting loop system in existing PVC Conduit/ casing capping using 2x1.5Sqmm (Phase&Neutral) & 1x1.0sqmm (Earthwire )FRLS multistrand PVC insulated copperwire (confirmingtoIS-694: and latest amendments) with a 6Amps flush type SP control switch shall be fixed on the existing plastic sheet/gangbox, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet. Medium point above 3Mtr upto 6Mtr from tapping point to outlet via switch Point 2 394.00 788.00

19 Supplying of .....feet -PVC Batten with integrated LED tube .... W with high quality diffuser with Life of 25000 burning hours & 70% lumen maintenance with CRI > 80. Power Input: 220-240V@ 50/60Hz & Power factor >0.9 along with CE approved. 2 years Warranty against any manufacturing defect working under standard electrical condition. 1 x 4' - 20/22 W No 3 690.00 2070.00

20 Supplying heavy gauge PVC Conduit Pipe ….dia .......mm thick with suitable size bends, metal junction boxes adhesive paste etc., by groove cutting in the wall and fixing by bracing U or J hooks and cement plastering up to the wall surface and run with 18 SWG GI fish wire run throughout the conduit wherever necessary. 25mm dia 2mm thick m 20 78.00 1560.00

21 Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper with low conductor resistance single core wire in open or consealed system of wiring with specified IS-694:1990 & confirming to GTP of GROUP-A. a) 2.5 sq mm - for Lighting Circuit. m 25 42.00 1050.00

22 Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper with low conductor resistance single core wire in open or consealed system of wiring with specified IS-694:1990 & confirming to GTP of GROUP-A. b) 4.00 sq mm - for Heating Circuit. m 15 63.00 945.00

23 Fixing all types and all capacities of fluorescent/ falseceiling/ spotlight/ CFL/LED fittings indoor on the wall/ ceiling/ rafters/ girdersusing 23/0.0076"twintwisted PVC insulated wires, required Nos of round blocks and clamps.On wall/ ceiling / Rafter / Girders Each 3 122.00 366.00

24 Supplying and fixing surface/flush mounting unbreakable PVC modular box suitable for mounting modular switch plates with due groove cutting in Brick/C.Cwall, including necessary rawlplugs, Machine/NF screws etc., complete. 8Way Each 1 219.00 219.00

25 Supplying and fixing superior quality modular switch mounting polycar bonate plate with necessary supporting back plate with required nos .of machine screws, bolts nuts etc., complete on the existing metal/ PVC box. 8Way Each 1 284.00 284.00

26 Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 8Way Each 1 250.00 250.00

27 Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293.6A One Way Switch Each 1 88.00 352.00

28 Providing Size Stone masonry with hard stone in foundation & plinth with Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 9.58 6364.00 60967.12

29 Providing ruled pointing to coursed stone masonry with cement mortar 1:3, after racking joints to depth of 20mm nicely including cost of materials, labours, curing complete as per the specifications. Sqmtr 0.13 199.00 25.87

Total Civil Portion 318340.12

Basic Rate (Supply+Errection+ Civil) 1,020,824.36

Note: 1. Supply of equipment and materials shall include loading and unloading

2. The bidder shall quote same rates for common materials in all the schedules of the price sheet.

Place Designation

Name of the company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 3A(iii) - Tender schedule for Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Bidder's Name & Address along with GSTIN no. :

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

BIDDERS SHALL FILL ONLY IN THE LIGHT BLUE COLOURED CELLS.

Sl. No. Name of the Equipment/Materials Unit Qty Rate Total qty

Work Order Nos: Y-438/27.01.2025

A Material portion

1 11 kV, 400 Amps Special Roaster GOS set 7 14956.00 104692.00

2 9 kV, 10 kA Lightning Arrester (metal oxide type) Nos 21 1584.00 33264.00

3 2 hole paddle suitable for Coyote ACSR conductor 610A Nos 28 2250.00 63000.00

4 C Wedge connecctors suitable for Coyote ACSR conductor Nos 28 773.00 21644.00

5 Coyote ACSR Conductor m 50 164.00 8200.00

6 RCC Pole - 9 Mtr Long, 145 Kg WL Nos 14 7076.00 99064.00

7 Flexible copper earthing strip/bond having size of 450 mm long, 15 mm width and 3 mm thick both side lugs with nut and bolts Nos 14 563.00 7882.00

8 DP Set (2 Pole Strucrure Kit) For RCC Pole - 9 Mtr Long, 145KG WL/PSCC Pole - 9 Mtr Long, 300Kg WL - GI Set 7 8863.00 62041.00

9 Aluminum Lugs 185Sqmm Nos 42 39.00 1638.00

10 Name plates Nos 21 333.00 6993.00

11 Danger plates Nos 7 333.00 2331.00

12 H - Frame Set for fixing 11 kV, 200 Amps Single Break GOS - (For DP structure for providing New GOS for sectionalisation) - GI set 7 6071.00 42497.00

Total Supply Portion 453246.00

A Labour portion

1 Supplying & Providing 450 mm dia 450 mm height 1.5" to 2" thick hume pipe collar (non pressure type) for earth pits including all lead and lifts etc., Nos 14 1499.00 20986.00

2 Grounding of equipments by providing cast iron pipe of 100 mm ID 13 mm thickness, 2.75 metres long with 2 part clamp out of G.I. Flat 50 X 6 mm continuously welded alround the pipe using cast iron welding electrodes as per drawing including the cost of excavation (All materials to be supplied by the contractor) Set 14 3491.00 48874.00

3 Grounding of equipment with 50 x 6 mm G. I. Flat and connecting Equipment to the earth mat/ ground pit. Each point of earthing with all formation works like bending, twisting, drilling of holes and connecting by welding (inclusive of all T&P and consumables) to the earth mat/ ground pit/ point of earth connection, all the materials supplied by the contractor. Rmtrs 400 335.00 134000.00

4 Formation of 11kV DP structre with 9 mtr. RCC pole Set 7 4134.00 28938.00

5 Mounting of 11 kV, 400 Amps Special Roaster GOS set 7 1214.00 8498.00

6 Mounting of H frame for fxing of GOS Nos 7 323.00 2261.00

7 Erection of 9 kV, 10 kA Lightning Arrester (metal oxide type) (1 set= 3 Nos) set 7 119.00 833.00

8 Fixing of equipment name plates and earthing name plates Nos 28 83.00 2324.00

9 Releasing of 11kV poles of D.P. Structure of outgoing feeders No 14 1001.70 14023.80

10 Releasing and Restringing((including pin binding, providing jumps, dead ending, etc.,) of Rabbit Conductor Per KM/Wire 2.5 9245.00 23112.50

11 Releasing of 11 KV isolator, Single Break 400 A Nos 7 1001.70 7011.90

12 Laying of 11 kV cables in existing trench/G.I. pipe/stoneware pipe/RCC hume pipe using wooden/aluminium rollers as directed by KPTCL staff mtr 21 72.00 1512.00

13 Releasing of 11 kV cables in existing trench/G.I. pipe/stoneware pipe/RCC hume pipe mtr 21 72.00 1512.00

14 Releasing and Refixing Insulator of 11 kV Dead End Insulator Disc, Strain etc No's 21 58.00 1218.00

15 Loading of Released H frames, RCC skeleton,DP kit and GOS set at Jog Muss MT 7.14 2061.00 14715.54

16 Unloading of Released H frames, RCC skeleton,DP kit and GOS set at Jog Muss MT 7.14 2061.00 14715.54

17 Transportation of Released H frames, RCC skeleton,DP kit and GOS set from Jog Muss to MWD, Store, Jog using 10t lorry km 250 46.85 11712.50

Total Labour Portion 336247.78

A Civil portion

1 Earth work excavation by manual means for drains,canals, waste weir, draft, approach channels, key trenches, foundation of bridges and such simillar works in all kinds of soils, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work. In all kinds of soils Depth upto 1.5 m. Cum 11.34 242 2744.28

2 Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately) Mix 1:4:8( M5) Using 40 mm nominal size graded crushed coarse aggregates Cum 0.7 5607 3924.90

3 Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) 2.2.1.1 M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (Footings) including Providing and removing centering, shuttering, strutting, propping etc., Cum 6.3 6369.52 40127.98

4 Removal of Unserviceable Soil with Disposal upto a suitable distance as directed by the Engineer incharge of work Cum 11.34 85 963.90

5 Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification All other type of structures kg 182 69.75 12694.50

6 Jelly Spreading (20-25 mm) : Supplying and providing jelly in the station yard of uniform thickness of 100 mm including the cost of materials, labour charges, required tools and plants etc., complete. Work shall be carried out as per the instructions of Engineerin- charge of works as per the standard procedure Sqmtr 142.5 177.3 25265.25

7 Skerting formation: Providing and constructing load bearing wall with Solid Concrete blocks of size 400x150x200mm having block density more than 1800kg/m3 and minimum compressive strength of 4.00 N/mm2 conforming to IS 2185 (Part - I) - 2005 and constructed with CM 1:4 as per IS 2572:2005 including cost of all materials, labour, scaffolding and curing, usage charges of machinery etc complete as per specifications. Sqm 13.4 1229 16468.60

Total Civil Portion 102189.41

Basic Rate (Supply+Errection+ Civil) Amount put to Tender 891683.19

Note: 1. Supply of equipment and materials shall include loading and unloading

2. The bidder shall quote same rates for common materials in all the schedules of the price sheet.

Place Designation

Name of the company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 4 ( MANDATORY SPARES )

SHEET FOR TECHNOCOMMERCIAL OPENING (UN - PRICED)

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

Bidders Name and Address along with GSTIN No.: To,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

Price Breakup for Mandatory spares as per Annexure - 4 of Section - I, General, Volume - II.

Sl. No. Item Description Unit Total Qty. Indicate whether "Own Manufactured" or "Bought out item"

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE-5 COMMERCIAL DEVIATION

SHEET FOR TECHNOCOMMERCIAL OPENING

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Please fill Only in the Light Blue Couloured Cell.

Please key in the SlNo.,Section , Clause , Description as given in bid sheets and finally your Statement of Deviation/Variations.

This Sheet would be opened at the Techno-Commercial Opening. Please refer Vendor Manual attached for further details.

For any further assistance for submitting your bids please call up KPTCL Office.

We agree to provide all original Documents in support of the information provided for verification upon request. (Key in as YES in the space provided)

We understand that the electonic bid submitted by us is a valid offer in accordance with IT Act. (Key in as YES in the space provided)

We are fully aware of the electronic bid formalities and abide by the same. (Key in as YES in the space provided)

If you are not deviating from any of the clauses mentioned please key in as 'NO DEVIATION' in the space provided.

Bidder's Name & Address alongwith GSTIN no. : To

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

I/we have read each of the Clauses mentioned in INVITATION FOR TENDERS , INSTRUCTION TO TENDERERS , CONDITIONS OF CONTRACT, SPECIAL CONDITIONS OF CONTRACT and COMMERCIAL TERMS AND CONDITIONS and all the sections of Bid documents.

The following are the commercial Deviations and Variations from and exceptions to the Specifications and documents for

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

These deviations and variations are exhaustive. Except these deviations, the entire work shall be performed as per your specifications and documents.

Sl. NO. SECTION CLAUSE NO. DESC. AS PER SPECIFICATION STATEMENT OF DEVIATIONS/VARIATIONS

Note : Deviations specified elsewhere in the specification will not be considered.

Place Designation

Name of the company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE-6 : TECHNICAL DEVIATION

SHEET FOR TECHNO-COMMERCIAL OPENING

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Please key in the SlNo., Section , Clause , Description as given in Bid sheets and finally your Statement of Deviation/Variations.

This Sheet would be opened at the Techno-Commercial Opening.

For any further assistance for submitting your bids please call up KPTCL office. Please fill only in the blue coloured cells.

We agree to provide all original Documents in support of the information provided for verification upon request. (Key in as YES in the space provided)

We understand that the electonic bid submitted by us is a valid offer in accordance with IT Act. (Key in as YES in the space provided)

We are fully aware of the electronic bid formalities and abide by the same. (Key in as YES in the space provided)

If you are not deviating from any of the clauses mentioned please key in as 'NO DEVIATION' in the space provided.

Bidder's Name & Address alongwith GSTIN no. : TO,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

The following are the Technical Deviations and Variations from and exceptions to the Specifications and documents for

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

These deviations and variations are exhaustive.Except these deiviations and variations, the entire work shall be performed as per your specification and documents.

Sl. NO. SECTION CLAUSE NO. DESC. AS PER SPECIFICATION STATEMENT OF DEVIATIONS/VARIATIONS

Note : Deviations specified elsewhere in the specification will not be considered.

Place Designation

Name of the company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE 7(List of special tools and tackles )

SHEET FOR TECHNOCOMMERCIAL OPENING

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Bidder's Name & Address alongwith GSTIN no. : TO,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

List of special tools and tackles the price of which is included in bid price.

Sl. No. For equipment Description of item Unit Quantity

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SHEET FOR TECHNOCOMMERCIAL OPENING

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

NOTE: 1 ) SHALL BE UPLOADED WITHOUT PRICES

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

We have enclosed(uploaded) with our proposal the following additional information.

Sl. No. Brief Description of information Ref. and Page No.

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE - 9 (1 of 5) : QUALIFYING REQUIREMENTS

SHEET FOR TECHNOCOMMERCIAL OPENING

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Please fill Only in the Light Blue Couloured Cell.

BIDDER'S NAME AND ADDRESS: TO,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

a) * We have uploaded bid as individual Bidder. (Key in Individual Bidder )

b) * We have uploaded bid in Consortium with the following Bidders. (Key in Consortium ) VOID

Name of Consortium Partner Scope / Participation of each Consortium Partner

(* Fill-up whichever is applicable)

1.0 GENERAL INFORMATION

The Bidder, bidding for this package are requested to complete the information in the following form.

Sl.No. Particulars Bidder details

1 Name of the Firm

2 Address of Head Office / Registered Office GST no.

5 Name of Contact person with Designation

6 Place of Incorporation/Registration

7 Year of Incorporation/Registration

8 Constitution or legal status of Tenderer [Upload copy]

9 Place of Registration [Upload copy]

10 Principal place of business

2.0 We are furnishing the following details/documents in support of Qualifying requirement for above mentioned project

Sl.No. Bidder details Indicate Yes /No

(a) Written power of attorney of the signatory on the bid to commit the bidder. In case of Consortium

1 Furnished / Not

2 Uploaded / Not

(b) Certificate of Registration of the Company. Please mention the date of incorporation of the company

1 Uploaded / Not

(c ) Valid Super Grade Electrical Contractor’s License issued by the Government of Karnataka as on the date of techno commercial Bid opening. Please mention the date of expiry of the License certificate issued by GOK/ Undertaking to this effect

1 Uploaded / Not

(d) Self declaration regarding Litigation w.r.t KPTCL contracts over the last five years (refer ITT)

1 Uploaded / Not

(e) Self declaration for ‘not being disqualified regarding non-performance in any of the Government utilities in the past five years’. (refer ITT)

1 Uploaded / Not

(f) An undertaking to source the supply of equipment/ material from KPTCL approved vendors only as per QR for Vendor registration, available in the KPTCL website ie., kptcl.karnataka.gov.in, Link Tendering & Procurement-Application for Vendor.

1 Uploaded / Not

(g) Self declaration regarding no action against the bidder have been taken by KPTCL in respect of Risk & Cost clause

1 Uploaded / Not

(h) Self declaration regarding 'Eligibility clauses in respect of restrictions on procurement from a bidder of a country which shares a land border with India as per Annexure-XVI

1 Uploaded / Not

(i) Self declaration regarding RESTRICTIONS ON SOURCING OF EQUIPMENTS/MATERIALS BY THE BIDDER FROM A VENDOR OF A COUNTRY WHICH SHARES A LAND BORDER WITH INDIA as per Annexure -XVII

1 Uploaded / Not

Section 3 : 1.3 Work performed of similar nature in the last Five years, preceding the date of Bid submissionof Bidder (Clause No: 3.2 (b) (i) & (ii) of ITT) - In respect of Sub Station portion and Transmission Lines resp.

Project Name Name & Address of the Employer Description of Work Voltage class Number of Sub-Stations/Length of the Line Contract Number Value of contract Rs. Lakh Date of issue of work order Specified period of completion Actual date of commissioning Remarks explaining reasons for delay in commisioning of work

Note : 1 . The documentary proof of fulfilling the qualifying requirements shall be uploaded along with the bid. The bidder shall upload the P.O,LOI/LOA, DWA, Work done, Performance Certificates issued by the end users not below the rank of Executive/ Divisional Engineer along with the bid.

2. The qualifying experience of the Bidder who is having qualifying experience shall be furnished in the above performa and Documentary Proof in support of above shall be uploaded in the form of certificates issued by authorized officers of concerned organisations.

3. IF this sheet is insufficient for furnishing the qualifying experience of the Bidder then similar sheets shall be seperately uploaded.

Date Designation

Place Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE - 9 (2 of 5) : QUALIFYING REQUIREMENTS

SHEET FOR TECHNOCOMMERCIAL OPENING

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

BIDDER'S NAME AND ADDRESS: TO,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

Section 3 : 1.5 Information on works for which Tenders have been submitted and works which are yet to be completed as on the date of this Tender of a Bidder

(A) Existing commitments and on-going works:

Description of work Place & State Contract No & Date Name and Address of Employer Value of contract (Rs. Lakh) Stipulated period of cof Completion Value of works remaining to be completed ( Rs.Lakhs) (Attach Certificates from Engineers –in- Charge) Anticipated date of commissioning

Note:Attach Certificates from Engineers –in- Charge

B)Works for which Tenders already submitted

Description of work Place & State Name and Address of Employer Estimated value of works (Rs. Lakh) Stipulated period of Completion Date when decision is expected Remarks if any

i) The statements showing the value of existing commitments and on-going works as well as the stipulated period of completion remaining for each of the works listed should be countersigned by the Employer in charge, not below the rank of an Executive Engineer or equivalent.

ii) A self-declaration is to be uploaded by the bidder stating that "the information with regard to assessed available tender capacity (Works on Hand) furnished are correct”.

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE - 9 (3 of 5) : QUALIFYING REQUIREMENTS

SHEET FOR TECHNOCOMMERCIAL OPENING

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

BIDDER'S NAME AND ADDRESS: TO,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

Following is the list of major supplied subsation equipments/accessories which are type tested and designed, manufactured by us in accordance with internationally recognised standards.

Sl. No. Item rating, type and Designation Qty Customer Date of Order Date of Supply Date of Commissioning Ref. of Cusomer's certificate of successful operation enclosed Ref. of layout & Customer's certificae for successful commission

Note: Documentary Proof in support of above shall be uploaded in the form of certificates issued by authorized officers of concerned organisations.

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE - 9 (4 of 5) : QUALIFYING REQUIREMENTS

SHEET FOR TECHNOCOMMERCIAL OPENING

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

BIDDER'S NAME AND ADDRESS: To

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

Section 3 : 1.7 Reports on the financial standing of the tenderer, such as Profit and Loss Statements and Auditor’s reports in the preceeding last five years, Audited Financial statements i.e Balance sheets, P&L statements, Turnover certificates duly certified by chartered Accountant as documentary evidence shall be uploaded.

SLNo. Particulars Year Lead Bidder Consortium Member

Mention Year Amount(Rs.) Mention Year Amount(Rs.)

Names of the constituent Firms VOID

1 Annual turn over for the last Five years Year(1) 2020-2021

2 Liquid Assets / Credit availability or access to evidence of assets

3 Whether Audited Balance sheets and Profit & Loss statement are enclosed for the last Five Years ? (yes/No)

4 Whether Bankers certificate enclosed for credit facilities? (Yes/No)

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

SCHEDULE - 9 (5 of 5) : QUALIFYING REQUIREMENTS

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

BIDDER'S NAME AND ADDRESS: TO,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

The information to be filled in by the Tenderer hereunder will be used for purposes of computing Tender capacity as provided for in Clause 3 of the Instructions to Tenderers. This information will not be incorporated in the Contract.

1.1 Constitution or legal status of Tenderer [Upload copy]

Place of Registration [Upload copy]

Principal place of business

Section 3: 1.2 Total value of works executed (KPTCL & NON KPTCL works) and payments received in the last five years (in Rs. Lakhs)

1.2 Total value of works executed (KPTCL & NON KPTCL works) and payments received in the last five years (in Rs. Lakhs) of Bidder Financial Year Details

KPTCL works Non KPTCL works

Total value of works in Rs. Lakh Total value of works in Rs. Lakh

Note: Attach relevant Certificate/s from Chartered Accountant.

Section 3: 1.9 Name, address, and telephone, telex, and fax numbers of the Tenderers' bankers who may provide references if contacted by the Employer.

Sl.No Name, address, and telephone, telex, and fax numbers of the Tenderers' bankers

1.12 Information on litigations in which the Tenderer is involved:

Other Party(ies) Employer Details of Dispute Amount involved Remarks showing Present Status

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE-10 (1 of 3) Details of Tools and Plants available

SHEET FOR TECHNOCOMMERCIAL OPENING

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

BIDDER'S NAME AND ADDRESS: To

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

Following are the details of the Tools and Plants available with us.

Sl. No. Description Quantity Make Present Location / Project Remarks (if any)

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE 10 (2 of 3) Details of Technical staff employed

SHEET FOR TECHNOCOMMERCIAL OPENING

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

BIDDER'S NAME AND ADDRESS: To

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

Section 3: 1.8 Qualification and experience of the key technical and management personnel in permanent employment with the tenderer and those that are proposed to be deployed on this contract, if awarded

Sl. No. Name of the employee Designation Branch (Degree/Diploma) Year of Passing Since when employed in erection division Past Experience

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE 10 (3 of 3 )

SHEET FOR TECHNOCOMMERCIAL OPENING

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

BIDDER'S NAME AND ADDRESS: To

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

We propose the following deployment of manpower for the Substation Portion and Line Package.

Sl. No. Category MONTHS AFTER PLACEMENT OF AWARD LETTER

1 Project manager

2 Sr. Project Manager

5 Skilled labour

6 No skilled labour

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE-11 (A) : COMPLETION SCHEDULE FOR STATION/TERMINAL BAYS

SHEET FOR TECHNOCOMMERCIAL OPENING

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

Bidders Name and Address: To,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

We hereby declare that following schedules shall be followed by us for the above work. The period of various activities from the date of placement of award letter shall be as follows

Commencement Completion

1 Detailed engineering

2 Procurement of bought out items / raw materials

3 Manufacturing & Testing

5 Setting up of site office, Sheds & stores etc.

7 Concreting for

a)Structure Foundations

b)Equipment and mounting structure foundadions

c)Cable trenches

2. Installation

8 Receipt(at site) of

a)Main equipment / spares

c)Insulators & Hardwares

d)Clamps & Connectors

e)Marshalling kiosks

f)Cables & Cabling Materials

a)Main structures

b)Equipment support structures

10 Equipment Erection

12 Bus bar erection

15 Completion of testing and ready for commissioning

16 Commissioning

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE-11B : COMPLETION SCHEDULE FOR TRANSMISSION LINES

SHEET FOR TECHNOCOMMERCIAL OPENING

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

Bidders Name and Address: To,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

We hereby declare that following shedules shall be followed by us for the above work. The period of various activities from the date of placement of award letter shall be as follows.

SL.NO Activity Period in Months for the Work of Construction of 66kV Transmission Lines

Commencement Completion

1 Submission of Drawings

2 Completion of detailed engineering

3 Commencement of Manufacturing

4 Completion of Manufacturing

5 Readiness for testing

6 Readiness for Shipment

7 Receipt at Site

8 Completion of Shipment

1 Detailed Survey

2 Setting up of site office, sheds and stores etc.

3 Exacavation for foundations.

4 Foundations and other Civil Works

5 Erection of Tower alongwith accessories

6 Stringing of conductor/ groundwire alongwith accessories

7 Testing , Commissioning and Handing over.

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 12 TYPE TESTS & TEST CHARGES OF EQUIPMENT/MATERIALS

SHEET FOR TECHNOCOMMERCIAL OPENING

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

BIDDERS SHALL INDICATE VARIOUS TYPE TESTS IN LIGHT BLUE COLOURED CELLS

ALL THE TYPE TESTS APPLICABLE FOR EACH OF THE EQUIPMENTS SHALL BE INCLUDED.

Bidders Name and Address To,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

SL.No Details of Equipments Type Test Test Charges ( in Rs )

1 Power Transformers: VOID

b) 100MVA,220/110kV VOID

b) 10MVA,110/11kV VOID

2 SF6 Circuit Breakers:

4 Current Transformer:

5 Voltage Transformers:

6 Capacitive Voltage Transformers:

7 Surge Arrestors

8 a) Relay & Protection Panels

b) Substation Automation

9 L.T. A.C Panel

10 Station Battery

11 Station Battery Charger

12 PLCC Battery

13 PLCC Battery Charger

14 1.1KV Copper control cables/LT Power Cable

15 11KV U.G Cable

16 PLCC equipment

17 Conductors & Earth Wire a) Drake ACSR

b) Coyote conductor

c) Lynx conductor

18 Insulators a) 120/90KN Disc Insulator Strings

b) Solid Core Insulators

c) Silicon rubber/ Disc/ Long rod insulators

d) Post Insulators

19 Station / Mounting Structures

21 Hardware Materials

22 Aluminium pipe and Clamps

23 AC DISTRIBUTION BOX

24 DC DISTRIBUTION BOX

25 Nitrojen Fire Fighting Protection System

NOTE: The Type Test / Special Tests, if repeated at the insistance of owner, the applicable testing charges shall be paid by the successful Bidder upfront to the laboratory and the same shall be reimbursable by KPTCL as per actuals on submission of Bills along with proof of payment and on successful completion of all the Type Tests, specified and on approval of the same by the owner. In case equipment/material fails in the type tests during testing then the testing charges paid by the Bidder to the laboratory will not be reimbursed by KPTCL. The above Clause is applicable for all the equipments/materials, in case, the Type Test / Special Tests, are repeated at the insistance of owner(KPTCL).

Place Printed Name

Karnataka Power Transmission Corporation Limited

Schedule -13-List of Optional Spares

SHEET FOR TECHNOCOMMERCIAL OPENING

Combined Package of Work A: Replacement of Five Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220/400kV Station, KPTCL, Talaguppa. Work B: Replacement of Two Nos Age old/Obsolete M/s CGL make 220kV SF6 Circuit Breaker by new M/s CG power make 220kV SF6 Circuit Breaker at 220KV Station, KPTCL, Balligavi Work C: Providing 2 Nos of additional 11kV MCVCB MEI make switchgear at 110/11kV substation Talaguppa coming under 400kV station and SSM Division, KPTCL, Talaguppa. Work D: Replacement of 7 Nos of 11kV DP set at 110/33/11kV substation Jog coming under 400kV station and Operation Division, KPTCL, Talaguppa.

Indent No: KPTCL/2025-26/SS/ WORK_INDENT3419

BIDDERS SHALL NOTE THAT QUANTITIES INDICATED IN THE ITEM_WISE FINANCIAL BID OFFER SHALL BE INDICATED HERE ALSO.

Bidders Name and Address To

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

Sl. No. For Equipments Details of item Unit Quantity

Place Designation

Name of the Company