Circuit House at Biswanath District, Assam

Amount

EARTHWORK IN EXCAVATION Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and dis`posal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil

Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete. (Measurements to be taken of the face area timbered).

Close timbering in case of shafts, wells, cesspits, manholes and the like including strutting, shoring and packing cavities (wherever required) etc. complete.(Measurements to be taken of the face area timbered). Depth exceeding 3 m but not exceeding 4.5 m.

Supplying and filling in plinth with local sand under floors, including watering, ramming, consolidating and dressing complete.

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor : With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shttering - All work up to plinth level 1:3:6 (1 Cement : 3 coarse sand(zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shttering - All work up to plinth level 1:4:8 (1 Cement : 4 coarse sand(zone-III) : 8 graded stone aggregate 40 mm nominal size).

Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4(1 Cement : 4 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 12.5 mm nominal size derived from natural sources).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Centering & shuttering including strutting, propping etc. and removal of form work for: Foundations, footings, bases of columns, etc. for mass concrete

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Steel reinforcement for R.C.C. work ncluding straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level

All works above plinth level upto floor V level

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in : Cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : In proportion 1:5.

Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing 1st class ceramic glazed wall tiles conforming to IS 15622 ( thickness to be specified by the manufacture) of approved make,in all colours,shades except burgundy,bottle green,black of any size as approved by Engineer in charge .in skirting,risers of steps and dados over 12 mm thick bed of cement morter 1:3 ( 1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). with sal wood

Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDM gasket, Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 2.50 sqm upto 4.00 sqm.)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 300x16 mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : Tower bolt ( 300 x 10 mm )

Tower bolt ( 250 x 10 mm )

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 200x10 mm

Providing and fixing aluminium handles ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 125 mm

Two track two panels sliding window made of (small series) frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. (40 mm thick with 20 mm nominal size stone aggregate ) 40 mm thick with 20 mm nominal size stone aggregate

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 , of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. The tiles must be cut with the zero chipping diamond cutter only.Laying of tiles will be done with the notch trowel,plier,wedge,clips of required thickness , leveling system and rubber mallet for placing the tiles gently and easily Size of Tile 800x800 mm ( Double Charge )

Size of Tile 600x600 mm ( Matt/Antiskid) )

Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gm/ m²

Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J. or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275 gm/m²

12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part Iand laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement : 4 fine sand)

20 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement : 4 fine sand)

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 12 mm cement plaster

6 mm cement plaster of mix : 1:3 (1 cement: 3 fine sand)

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Extra for plastering done on moulding cornices or architraves including neat finish to line and level: In two coats

Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm).

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade New work (Two or more coats applied @ 1.43 ltr/ 10 sqm. over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer.

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10sqm of approved brand and manufacture

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre. of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats.

Supplying and stacking at site. 53 mm to 22.4 mm size stone aggregate.

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density

Dry brick pitching half brick thick including supply of bricks and preparing the surface complete : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-II (size range 53 mm to 0.075 mm) having CBR Value-25

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineer in-Charge. 80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern.

Providing and placing in position 100 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work 80 mm nominal inner dia. Pipes.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : External work 32 mm dia. nominal bore

50 mm dia. nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 80 mm nominal bore Vertical

Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately).

Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200mm length), fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as per direction of Engineer -in-charge.

WATER PROOFING OF CHAJJAS, ROOF SLABS, TERRACES, SUNKEN SLABS, SEPTIC TANK,OH TANK, RAFT SLAB IN BASEMENT, WALLS ETC. Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. (For the purpose of measurement the entire treated surface will be measured.)

Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in Charge.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. All types of soil 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings& accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer- in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS:11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). With 15 mm thick Tegular edged light weight calcium sliciate false ceiling tiles

6 Passenger Lift with power operated centre opening doors and AC variable voltage & variable frequency controls.

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : Screened through Sieve of I.S. designation 4.75mm

Rough dressing the trenched ground including breaking clods.

Fine dressing of the ground.

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately Holes 90 cm dia, and 90 cm deep

Holes 60 cm dia, and 60 cm deep

Providing and watering of irrigation water through water tanker of Horticulture features i.e. lawn, tree, shrubs, hedge/edge, ground cover etc. at the site of work. Water tanker having 5000 lit. capacity with one labour for watering i/c cost of water, filling of tanker, wartering at site with all leads and lifts as per direction of officer-in-charge.

Anti termite treatment by digging holes 30 cm deep and 4 cm dia, 6 to 7 holes around the tree using chemical emulsion at the rate of 1.5 liter per hole in two time or more application to get the trees free from termite infection chemicals used Chlorpyriphos 20% EC in the ratio of 1% concentration and as per direction of officer-in-charge.

Providing and applying anti termite treatment of infected trees i/c all branches/leaves by spraying chemical emulsion 0.5% (Chlorpyriphos 20% EC) concentration through power spray machine (@ 100 ml Chlorpyriphos per tree i/c cost of chemical) and as per direction of officer-in-charge.and as per direction of officer-in-charge.

Anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in 499 liters water and applying solution @ 1.00 litre solution per sqm lawn or bed area.(two application) i/c cost of chemical)and as per direction of officer-in-charge.and as per direction of officer-in-charge.

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Trees Plant

Shrub Plant

Hedge/Ground cover Plant

Providing and fixing of Tuflex Garden fencing Hexagonal net/or equivalent of green colour having contents ( Weight grams/sqm. 510 (+/- 8%)) in width of 60 cm. with bamboo of 90 cm. length. The bamboo should be painted with green colour paint of approved brand and manufacture (two or more coats) and fixed 30 cm. below ground level and 60 cm. above ground level at a distance of 1.50 mtrs. The net and bamboo should be binded with 2 mm. G.I. Wire at three places properly as per direction of Engineer-in-charge.

Providing and stacking of Bottle palm of ht. 270-300 cm bottom girth 40-50 cm well developed in big HDPE bags as per direction of the officer-in-charge

Providing and stacking of Pterospermum acerifolium (Kanak Champa) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Tabebuia sp. of height 150-165 cm. in big polybags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Bauhinia tomentosa (yellow) of height 60-75 cm. in earthen pots of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Cestrum nocturnum (Raat ki Rani) of height 60-75 cm. with 4-5 branches in bag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Ficus panda of height 60-90 cm, with 8-10 branches, and healthy foliage, bushy in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Hamelia patens of height 60-75 cm. with 6-8 branches in poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Nerium oleander variegated of height 60-75 cm., multibranched in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Tecoma gaudichaudi of height 90-105 cm.,bushy in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Alternanthera species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Daniella variegated, with 3 to 4 variegated leaves in 20 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Iresine herbstii, of height 20-25 cm. full of branches well developed in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Syngonium (Butterfly) variegated with 2-3 suckers healthy foliage in Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge.

Providing and stacking of Tradescantia, full of leaves in Earthen Pot/Plastic Pot of size 15 cm. as per direction of the officer-in-charge.

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan), including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m,as per directions of Engineer in Incharge. All kinds of soil

Supplying and spreading of sand in lawn area, including watering, and dressing complete.

Providing Circular Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 Nos ( 3 nos horizontal & 4 nos vertical “ U “ shape) M.S. wires of 3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of Officer-in-charge. Top inside dia 30 cm, outer bottom dia 20 cm, total height 30 cm with wall thickness of 25.4 mm

Providing and displaying of Areca Palm having ht. 1.80 m to 2.10 m with 8 to 10 suckers, well developed, fresh and healthy with lush green foliage in 30 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Raphis Palm having ht. 75 cm to 90 cm with 15 to 18 equal suckers, well developed, full of fresh and healthy leaves from bottom to top in 35 cm PVC Pots/C.Pots & as per direction of the officer-in-charge.

Providing and displaying of Seaforthia Palm having ht. 1.50 m to 1.80 m with 12-15 suckers, well developed, fresh and healthy lush green leaves from bottom to top in 30 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and Displaying Coleus broad leaves having 3 to 4 branches equal well developed with fresh & healthy foliage in different colour in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying Gazania hybrid in different colour well developed with fresh & healthy foliage with full bloom in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: G.S. Sheet

Dismantling steel work in single sections including dismembering and stacking within 50 metres lead in: R.S Joists

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area beyond 3 sq. metres

Supply and Installation of Anutone Subtex Nubby Graphics, square edge, Glassfibre core fully encapsulated ceiling tile of size 595x595x15mm having volume density 120Kgs/m3, weight 1.8kg/m2 which is suspended by using 0.3mm thick Anutone Skelet TrelisT15 metal grid system. Anutone Skelet TrelisT15 metal grid system of 600x600mm module includes Anutone Skelet WA15W30 wall angle with unequal flanges of 15/19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the Anutone Skelet MT15W36 MainT with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres. Anutone Skelet CT15W12 CrossT with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm centers in the perpendicular direction to the Main T15. Finally Anutone Skelet CT15W06 CrossT with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the CT15W12 CrossT in direction parallel to the Main T15 to result in 600x600mm module. Anutone Subtex Nubby square edge of size 595x595x15mm shall be placed into the grid size of 600x600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. Technical Parameters • Fire (Class) – 1 & P • Acoustics – NRC 0.9 (For E900 Mounting) • Thermal conductivity (W/mk)– 0.066 • Climate (°C, RH) – 40, 95 • Light reflectance (%) – 85 • Green (VoC, RC %) – Low, 35

Supply & installation of Anutone Salon Slats Surco made of pinewood E1 grade fiberboard, melamine/veneer laminated finish, groove perforated slats L16-2 - (2mm Slats @16mm pitch) / L32-2 - (2mm grooves @ 32mm centers), backlined with Soundtexblack acoustical fleece, tongue-groove edge for a seamless look,Non FR, size 128x2440x16mm, volume density of base board 800Kg/m3, weight 8Kgs/m2 (L16), 10.5Kgs/m2 (L32), 11Kgs/m2 (L64) installed by using Anutone Strut framework system. Anutone Strut framework system includes Anutone Strut CC10 aluminium core cross channel having thickness 0.55mm, length 3600mm, knurled web 40mm, depth 10mm and equal flanges 15mm is fastened to wall or framework behind vertically/horizontally at every 600mm c/c. Anutone Strut CC18 aluminium core cross channel, thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge &centre brackets is then fixed perpendicular to the Strut CC10 Cross channel with the help of fasteners at every 400mm centers. Slats Surco of size 128x 2440x16mm in then fixed perpendicular to CC18 with suitable edge & centre brackets. Short edges of the panel are staggered. Contractor to provide expansion joints of 3mm at every 4.88m length wise and 4.992m width wise. Technical Parameters • Acoustics – NRC 0.77 (For E300* Mounting) • Thermal conductivity (W/mk)– na • Climate (°C, RH) – 50, 70 • Light reflectance (%) – 75 (Maple Arce) • Green (VOC, RC %) – Low, 25

Providing and fixing brass stop cock of approved quality : a) 20 mm nominal bore

8 mm dia C.P. Brass/ S.S. Jet with flexible tube upto 1 metre long with S.S. tringular plate for Eureopean type W.C.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : a) 100 mm inlet and 100 mm outlet i) Sand cast iron S&S as per IS: 3989

Providing and fixing medium duty S.S. Floor grating with frame of approved design brand including setting in floor with cement motor to match with floor finish as per architect requirement including cutting and making good floor or wall wherever required. a) 125mm dia

Providing, fixing, testing and commissioning of CP Brass Health Faucet with nuts, washers of approved brand including cutting and making good the walls wherever required. Rate of flow should be 4 LPM

Providing and fixing toilet paper holder : a) C.P. Brass

Providing and fixing P.V.C. WC connector (straight or bend type) with rubber lip ring. Including 110 mm dia PVC pipe / bend of required length and proper connection with M seal to C.I. pipe complete as required

Providing, fixing, testing and commissioning of CP Brass coat hook of with nuts and washer of approved brand including cutting and making good the walls wherever required as directed by Engineering Incharge.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: (a) White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

PTMT - Waste Coupling 31/32 mm

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing brass stop cock of approved quality : a) 20 mm nominal bore

8 mm dia C.P. Brass/ S.S. Jet with flexible tube upto 1 metre long with S.S. tringular plate for Eureopean type W.C.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. a) 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : a) Kitchen sink with drain board i) 510x1040 mm bowl depth 250 mm

15 mm C.P. brass tap

Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe.

Providing, fixing, testing and commissioning of white vitreous china large urinal partition with concealed CI bracket, cutting and making good as required.

Fixing, testing and commissioning of vertical, free and standing, water cooler, 150 litre per hour cooling and storage capacity, with stainless steel tank, SS panels, PUF insulation, gravity saled faucet with zero leakage, hermatic compressor, condenser with fan, thermostat,two cold water outlets, suitable for operation on 230V+ 10%, 50 cycles single phase supply along with 3 KVA automatic voltage stabiliser wiring, foundation as required, including 'Eureka Forbes' make Aquaguard, Hi-flo model with flow rate of 3 litres/ minute.

Providing, Fixing, testing and commissioning of Concealed type Stop valve 20mm dia including nuts, bolts and washers of approved brand including cutting and making good the walls wherever required.

Fixing, testing and commissioning 15mm CP 3 in one Wall Mixture with provision for over head shower, spout, hand shower with 115mm long bend pipe on upper side, connected legs and wall flange even with flexible pipe and bracket complete as required. (model will be specified by Architect or Client). Rate of flow for Shower with in 8 LPM

Fixing automatic high pressure electric water heaters with glass lining thermostats with each element and high temperature cut off, necessary insulation, safety valve, etc., all complete. a) 15 Ltr Capacity

Fixing, testing and commissioning 15 mm dia 600 mm long flexible braided pipe of approved brand including nuts and washer and making connection to fixture and fittings complete as required.

Fixing, testing, and commissioning of Concealed thermostatic mixer with valves & divertor for overhead shower & hand shower.

Providing, fixing, testing and commissioning of uPVC SWR pipe confirming to IS-13592, Type-A cut to required lengths including all necessary fittings and special such as bends, junctions offset, access pieces (plain or door), Tees, bends, reducers, flanges, clean out plug, plugs unions and clamps Fixing at wall / ceiling level supported by G.I. clamps, hangers etc. duly epoxy coated including chasing, cutting and making good the walls / floor etc. wherever required FOR RAIN WATER SYSTEM a) 110 mm O.D type "A"

Providing, fixing, testing and commissioning of uPVC SWR pipe confirming to IS-13592, Type-B cut to required lengths including all necessary fittings and special such as bends, junctions offset, access pieces (plain or door), Tees, bends, reducers, flanges, plugs unions and clamps Fixing at wall / ceiling level supported by G.I. clamps, hangers etc. duly epoxy coated including chasing, cutting and making good the walls / floor etc. wherever required FOR SOIL, WASTE AND VENT SYSTEMS a)110 mm O.D type "B"

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. a) Semi rigid pipe i) 32 mm dia

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. a) Semi rigid pipe i) 40 mm dia

Providing and fixing uPVC cowl complete including cutting and making good the walls and floors wherever required. a) 110 od

Providing & fixing M.S. structural work fabricated from standard section e.g. M.S rounds, angles, channels, plates including cutting to size,drilling,welding fixing and welding to insert plates in RCC structural members as directed by engineer-in-charge including cutting and making good the walls, ceilings and floors (for pipe supports, clamps etc.) (Gratings over drain).

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. a) 15 mm nominal outer dia Pipes

b) 20 mm nominal outer dia Pipes

c) 32 mm nominal outer dia Pipes

e) 40 mm nominal outer dia Pipes

f) 50 mm nominal outer dia Pipes

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : b) 20 mm nominal bore

Providing and fixing in position of approved quality high pressure rated Gun Metal Float Valve with copper ball float and brass rods of required length suitable for test pressure of not less than 15 Kg/sqcm of the following sizes: c) 50 mm dia

Effecting disinfections of water lines including overhead water tanks with Bleaching Powder as directed by the Project-in-Charge.

Suppling all materisls labour and tools and cost of drilling 200mm x 165mm bore well in all kinds of soil and rock in rural area for installation of pump set with hydrolic DTH rig machine, all complete including suplying all materials tools, drilling rig, Air compressor and equipments, as well as fuel, lubricants and cost of transprtation of Rig machine and other vehicles up to the site.

From 0.0M to 50.0 M belew G.L

From 51.0 M to200.00 M belew G.L

supplying all tools, tackles & lowering of 200 mm dia MS ERW casing pipe of 6mm wall thickness including welding charges, cost of pipe itc including all taxes, VAT, Excise duty, freight charges with inspection charges etc as applicable, etc all complete job.

Cleaning Flushing and devloping of drilled hole for testing the discharge of water development of bore well by continueous flow of water bu using heavy compresser upto satisfaction of E/I. To get uniterrupted flow of water free from sand and soil etc.

Supplying and fitting M.S cap over 200mm dia casing pipe as per direction of E/I For safety of rilling bore including providing of guard for safety of the same till returned final.

Supplying 100 mm dia submersible pump sets confirming to IS 8034 and motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/ noryl impeller. Motor suitable for working on 415V + 10%, 3PH, 50 Hz, A.C. supply with cable guard, thrust carbon/ fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined non return valve shall be provided with pump. 3 meter submersible copper conductor cable in single/ double run shall be provided with each pump. Submersible Pump 150 mm dia ( with Bronze impeller) up to 8 stages 5.0 HP

Supplying 3 core flat flexible submersible cable with, copper conductor, PVC insulated and PVC sheathed. 3 Core 4mm thickrequired.

2 no heavy duty clamp 40mm dia suitable for 200 mm dia pipe with all complete job.

Supplying & lowering 40mm da column G. I. pipe with all complete job.

Providing, laying, jointing and testing in position DWC HDPE pipes conforming to IS:16098 (Part 2): 2013 (SN-8) and suitable for the respective working pressures with all fittings and specials,e.g.couplings, tees, bends, reducers, end plugs etc., jointing by fusion welding method as per manufacturers recommendations all complete including excavation in all kind of soil and mooram filling. (SewerageLines) c) 200 mm dia

Providing, laying, jointing and testing in position DWC HDPE pipes conforming to IS:16098 (Part 2): 2013 (SN-8) and suitable for the respective working pressures with all fittings and specials,e.g.couplings, tees, bends, reducers, end plugs etc., jointing by fusion welding method as per manufacturers recommendations all complete including excavation in all kind of soil and mooram filling. (SewerageLines) c) 250 mm dia

Providing, laying, jointing and testing in position DWC HDPE pipes conforming to IS:16098 (Part 2): 2013 (SN-8) and suitable for the respective working pressures with all fittings and specials,e.g.couplings, tees, bends, reducers, end plugs etc., jointing by fusion welding method as per manufacturers recommendations all complete including excavation in all kind of soil and mooram filling. (SewerageLines) c) 300 mm dia

R.C.C. pipes NP2 class 150 mm dia. (Hume Pipe)

R.C.C. pipes NP2 class 250 mm dia (Hume Pipe)

R.C.C. pipes NP2 class 300 mm dia. (Hume Pipe)

R.C.C. pipes NP2 class 450 mm dia. (Hume Pipe)

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) b) Inside size 60 x 60 cm and depth up to 75 cm

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) c) Inside size 75 x 75 cm and depth up to 75 cm

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) a) Inside size 45 x 45 cm and depth up to 60 cm

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) b) Inside size 60 x 60 cm and depth up to 75 cm

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) c) Inside size 75 x 75 cm and depth up to 75 cm

Inside size 90x80 cm and 45 cm deep including C.I. coverInside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing, fixing , testing and commissioning threaded / flanged water meter with direct reading dial in KL with all necessary fitting such as threaded pieces, unions pressure gauge, isolation cock, flanges piece for future removal, flanges / unions complete with all necessary testing charges and obtaining test certificates from municipal authorities, on following size pipe lines (1 no. strainer shall be provided at inlet and cost shall be inclusive for the same).

Effecting connection from Existing/ Municipal Water Supply line including necessary excavation & making good the same including cutting, boring and tapping the Existing line by providing and installing ferrule / Tee connections with necessary fittings as required and making good the same. The rate for this item also includes complete services from the contractor for liasoning works such as filing necessary applications, submission of forms for approval to the municipal authorities, depositing the fees / other amounts as required for getting the premises / installations, inspected and approved and all other formalities required till the water connection is obtained. All the expenses incurred in this regard shall be borne by the Contractor except for the official payments to be made for any security deposit etc. which will be reimbursed on production of original voucher.

Supplying, fixing, jointing and testing in position the following medium grade (Class B) GI pipes for pump room, confirming to IS:1239 cut to required lengths including all necessary fittings of equal class (all fittings shall confirm to IS:1879 - part 1 to 10) and specials such as bends, tees, unions, reducers, flanges & plugs etc including standard specials as required, supporting laid on PCC 1:3:6 pedestals as directed, clamping it with necessary MS brackets and MS brackets for wall/ceiling support, including painting the pipes with two coats of enamel epoxy coated paints (in specific colour code) over two coat of specified primer, making necessary holes in walls, slab etc. and making good the same including testing the pipes to 10.54 kg/sq.cm after installation. Cutting hole in wall and making good the same as required. a) 50 mm dia

Supplying, fixing, jointing and testing in position the following medium grade (Class B) GI pipes for pump room, confirming to IS:1239 cut to required lengths including all necessary fittings of equal class (all fittings shall confirm to IS:1879 - part 1 to 10) and specials such as bends, tees, unions, reducers, flanges & plugs etc including standard specials as required, supporting laid on PCC 1:3:6 pedestals as directed, clamping it with necessary MS brackets and MS brackets for wall/ceiling support, including painting the pipes with two coats of enamel epoxy coated paints (in specific colour code) over two coat of specified primer, making necessary holes in walls, slab etc. and making good the same including testing the pipes to 10.54 kg/sq.cm after installation. Cutting hole in wall and making good the same as required.b) 65 mm dia (Ferrule connection & Borewell connection)

Laying, jointing and testing in position the following uPVC schedule 40 pipes including all necessary fittings such as elbow, coupler & tee etc. Cost shall be inclusive of excavation, dewatering, backfilling, ramming surrounding the pipe all round with minimum 150 mm thick all round compacted silver sand and providing thrust block standard complete as per specification and satisfaction of the Project Manager. ( Garden Irrigation Pipes) a) 80 mm dia

Laying, jointing and testing in position the following uPVC schedule 40 pipes including all necessary fittings such as elbow, coupler & tee etc. Cost shall be inclusive of excavation, dewatering, backfilling, ramming surrounding the pipe all round with minimum 150 mm thick all round compacted silver sand and providing thrust block standard complete as per specification and satisfaction of the Project Manager. ( Garden Irrigation Pipes) b) 65 mm dia

Laying, jointing and testing in position the following uPVC schedule 40 pipes including all necessary fittings such as elbow, coupler & tee etc. Cost shall be inclusive of excavation, dewatering, backfilling, ramming surrounding the pipe all round with minimum 150 mm thick all round compacted silver sand and providing thrust block standard complete as per specification and satisfaction of the Project Manager. ( Garden Irrigation Pipes) c) 50 mm dia

Laying, jointing and testing in position the following uPVC schedule 40 pipes including all necessary fittings such as elbow, coupler & tee etc. Cost shall be inclusive of excavation, dewatering, backfilling, ramming surrounding the pipe all round with minimum 150 mm thick all round compacted silver sand and providing thrust block standard complete as per specification and satisfaction of the Project Manager. ( Garden Irrigation Pipes) d) 40 mm dia

Laying, jointing and testing in position the following uPVC schedule 40 pipes including all necessary fittings such as elbow, coupler & tee etc. Cost shall be inclusive of excavation, dewatering, backfilling, ramming surrounding the pipe all round with minimum 150 mm thick all round compacted silver sand and providing thrust block standard complete as per specification and satisfaction of the Project Manager. ( Garden Irrigation Pipes) e) 32 mm dia

Laying, jointing and testing in position the following uPVC schedule 40 pipes including all necessary fittings such as elbow, coupler & tee etc. Cost shall be inclusive of excavation, dewatering, backfilling, ramming surrounding the pipe all round with minimum 150 mm thick all round compacted silver sand and providing thrust block standard complete as per specification and satisfaction of the Project Manager. ( Garden Irrigation Pipes) f) 25 mm dia

Providing & fixing C.I butterfly valve PN 1.0 (upto 150mm dia with hand lever operation & above 150 mm dia with gear box operation). Tested to a pressure not less than 16 Kg/Sq.cm. Including rubber gasket, flanges, nuts, bolts, washers, flanges as per table 'E' & painting complete as required. b) 80 mm dia

Providing & fixing C.I butterfly valve PN 1.0 (upto 150mm dia with hand lever operation & above 150 mm dia with gear box operation). Tested to a pressure not less than 16 Kg/Sq.cm. Including rubber gasket, flanges, nuts, bolts, washers, flanges as per table 'E' & painting complete as required. c) 65 mm dia

Providing & fixing C.I butterfly valve PN 1.0 (upto 150mm dia with hand lever operation & above 150 mm dia with gear box operation). Tested to a pressure not less than 16 Kg/Sq.cm. Including rubber gasket, flanges, nuts, bolts, washers, flanges as per table 'E' & painting complete as required. d) 50 mm dia

Providing, installation, testing and commissioning of GM Ball Valve, IS-318 LTB-2 SS Stem AISI 410, Ball SS 304/CF8, teflon gland packing, screwed female threads confirming to IS-554, b) 40 mm dia

PUMPS HOUSE : - Filter Feed Pumps: Supply, installation, testing and commissioning of Vertical Inline Split Coupled (with rigid aluminium alloy coupling between pump shaft and motor shaft) single stage centrifugal pump each capable of delivering the specified flow rate comprising the following and complete as per specifications. Casing (Volute) - Cast Iron (BS 1452 Grade 220) - PN 16 Impeller - Gunmetal Bronze (BS1400LG2C) - Statically and Dynamically Balanced Casing Gasket - Confined Non Asbestos Fiber Pump Shaft - SS (BS970 416) Flush Line - Braided Stainless Steel Mechanical Seal - Outside Balanced (the pump design shall met the requirement of servicing / changing the mechanical seal without disturbing the pump shaft alignment) Motor Type - TEFC Squirrel Cage, Efficiency Class - IE3, Insulation - Class F, 415V ± 10% , 50Hz ± 5%, 3Ø AC Power Supply (1 Working + 1 Standby) Capacity : 5 Cum/hr Head : 10 M RPM : 2900

Supplying, fixing, jointing and testing in position the following medium grade (Class B) GI pipes for pump room, confirming to IS:1239 cut to required lengths including all necessary fittings of equal class (all fittings shall confirm to IS:1879 - part 1 to 10) and specials such as bends, tees, unions, reducers, flanges & plugs etc including standard specials as required, supporting laid on PCC 1:3:6 pedestals as directed, clamping it with necessary MS brackets and MS brackets for wall/ceiling support, including painting the pipes with two coats of enamel epoxy coated paints (in specific colour code) over two coat of specified primer, making necessary holes in walls, slab etc. and making good the same including testing the pipes to 10.54 kg/sq.cm after installation. Cutting hole in wall and making good the same as required. a) 50 mm dia

Providing & fixing C.I butterfly valve PN 1.0 (upto 150mm dia with hand lever operation & above with gear box operation). Tested to a pressure not less than 16 Kg/Sq.cm. Including rubber gasket, flanges, nuts, bolts, washers, flanges as per table 'E' & painting complete as required. a) 50 mm dia

Providing and fixing gun metal non- return valve of approved quality (screwed end) : A) 50 mm dia

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : a) 50 mm nominal bore

Providing and fixing C.I. Y type Strainer including washer, nuts, bolts, 1.5 mm thick compressed asbestos gasket companion flanges as per table "E" complete. a) 50 mm dia

Providing and fixing M.S. galvanised puddle flanges (exact as per drawing) fabricated out of 6 mm thick M.S. plate of size 200 x 200mm plus dia of pipe of 600 mm long pipe pieces to R.C.C. water tanks / R.C.C. walls. The entire fitting shall be hot dipped galvanised. for UGR . a) 65 mm dia

Providing and fixing M.S. galvanised puddle flanges (exact as per drawing) fabricated out of 6 mm thick M.S. plate of size 200 x 200mm plus dia of pipe of 600 mm long pipe pieces to R.C.C. water tanks / R.C.C. walls. The entire fitting shall be hot dipped galvanised. for UGR . b) 50 mm dia

Providing and fixing 600 x 600 mm dia heavy duty sfrc/rcpc man hole cover for Under Ground domestic and fire water tanks as directed by Engineering Incharge

Providing and fixing PVC Foot Rest for UGR

WATER TREATMENT PLANT Installing, testing & commissioning of vertical MSEP filter with adequate dirt holding capacity (suitable for 5.5 Kg/Sqcm working pressure). Fabricated from MS sheet as per manufacturer's specifications complete with intitial charge filter media including painting inside with two coats of non toxic epoxy and with one coat of zinc chromate two coats of synthetic enamel paint outside. Including concrete foudation with cement plaster complete as required. The filter shall also be provided with set of internals for raw water inlet and bottom collecting system. Complete with frontal piping (heavy) and butterfly valves designed on 1.50 m / sec velocity. Multi Grated Filter for Domestic Water services. Filteration Rate 10000L/Sqm/Hr Testing pressure 5.5 Kg/Sq.cm Flow rate: 5 cum/hr

Activated Carbon Filter Filteration Rate 10000L/Sqm/Hr Testing pressure 5.5 Kg/Sq.cm Flow rate: 5 cum/hr

Iron Removal Filtration Filteration Rate 10000L/Sqm/Hr Testing pressure 5.5 Kg/Sq.cm Flow rate: 5 cum/hr

Supplying, installing, testing and commissioning of dosing system (for domestic water treatment plant) consisting of one HDPE tank of 200 litres capacity with a positive displacement diphragm dosing pump having variable flowrate of 0-6 lph. The motor shall be suitable for operation at 240 V/single phase/50 Hz. Supply. The pump shall be supplied complete with necessary polypropylene piping, valves, strainers, low level switch and injection fittings. The pump shall be speed & stroke control Asia LMI / equivalent make.

WIRING : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

4 Module (125mmX75mm)

6 Module (200mmX75mm)

8 Module (125mmX125mm)

12 Module (200mmX150mm)

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator) 6 way (4 + 18), Double door

8 way (4 + 24), Double door

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 2+6 way,double door

2+12 way,double door

2+16 way,double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

40 A Double pole mcb Isolator

63 A Double pole mcb Isolator

40 A Four pole isolator

63 A Four pole isolator

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 A

Supplying and fixing of 63 A rating, DP pole,415V, residual current circuit breaker (RCCB)having a sensitivity current 30 Ma and with 63A DP MCB in enclosure, complete with connections, testing and commissioning etc. as required.(FOR UPS I/C)

AC STARTER : Supply & Fixing 240 V, 25A Modular starter (Brand approved by EIC) on existing GI Modular type switch board with top cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. Mm

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3 core x 6.0 sq. mm. XLPE, Al.armoured cable.

3 core x 10.0 sq. mm. XLPE, Al.armoured cable.

4 core x 6.0 sq. mm. XLPE, Al.armoured cable.

4 core x 10.0 sq. mm. XLPE, Al.armoured cable.

4 core x 16.0 sq. mm. XLPE, Al.armoured cable.

3.5 core x 25.0 sq. mm. XLPE, Al.armoured cable.

3.5 core x 50 sq. mm. XLPE, Al.armoured cable.

3.5 core x 300 sq. mm. XLPE, Al.armoured cable.

Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 1 core x 10.0 sq. mm. XLPE, CU.armoured cable.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

EARTHING : Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but with charcoal/ coke and salt ) as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/submain wiring/ cable as required.

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

LIGHTNING CONDUCTOR: Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

CONDUIT : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

CABLE TRAY : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 50 mm depth X 1.6 mm thickness

PANEL Supply, Installation, testing & commissioning of compartmentalized type Lighting / Power Distribution boards as per Drawing, Specification. The unit rate shall include loading/unloading, shifting from site store to the place of installation, assembling the Panel including mounting & wiring of loose parts by manufacturers, interconnection of shipping sections, installation on readymade Cable trench (provied support for panel mounting) or directly on floor, assembling of loose accessories supplied by the manufacturer, wiring & connection of auxiliary circuits, installation, testing & commissioning of all Panel, supply of all necessary hardware. Aligning, levelling, grouting, testing and setting of relays and meters including all. MAIN LT DISTRIBUTION PANEL: INCOMING: 2 No 320 A, 4P MCCB 2 set (3 nos each) RYB cluster type LED phase indlcation lamps. 2 set (3 nos each) - ON/OFF/TRIP cluster type LED indication lamps. BUSBAR SECTION-1 1 set - 400A, 415V, 50HZ, 31 MVA Amps symmetrical continuous rated Copper busbars mounted on suitable hylam /DMC / SMC insulators /supports with proper graded colour coded heat shrinkable PVC sleeves. INTERLOCK BETWEEN 2 NOS 320A MCCB INCOMERS OUTGOING: 100 Amps TPN MCCB - 3 Nos.(with Rorary handle) 63 Amps TPN MCB - 2 Nos. 40 Amps TPN MCB - 9 Nos. PANEL AS ABOVE(Refer SLD)

FLOOR PANEL 1 INCOMING: 1 No 100 A, 4P MCCB 1 set (3 nos each) RYB cluster type LED phase indlcation lamps. 1 set (3 nos each) - ON/OFF/TRIP cluster type LED indication lamps. BUSBAR SECTION-1 1 set - 125A, 415V, 50HZ, 31 MVA Amps symmetrical continuous rated Copper busbars mounted on suitable hylam /DMC / SMC insulators /supports with proper graded colour coded heat shrinkable PVC sleeves. OUTGOING: 63 Amps DP MCB - 4 Nos. 40 Amps DP MCB - 9 Nos. PANEL AS ABOVE(Refer SLD)

FLOOR PANEL 2 INCOMING: 1 No 100 A, 4P MCCB 1 set (3 nos each) RYB cluster type LED phase indlcation lamps. 1 set (3 nos each) - ON/OFF/TRIP cluster type LED indication lamps. BUSBAR SECTION-1 1 set - 125A, 415V, 50HZ, 31 MVA Amps symmetrical continuous rated Copper busbars mounted on suitable hylam /DMC / SMC insulators /supports with proper graded colour coded heat shrinkable PVC sleeves. OUTGOING: 63 Amps DP MCB - 5 Nos. 40 Amps DP MCB - 8 Nos. PANEL AS ABOVE(Refer SLD)

Cable Supply : Supplying of following 1100 volt grade XLPE insulated PVC inner sheathed and FRLS PVC outer sheathed aluminium conductor armoured cables as per specification. 4 core x 6.0 sq. mm. XLPE, Al.armoured cable.

4 core x 10.0 sq. mm. XLPE, Al.armoured cable.

4 core x 16.0 sq. mm. XLPE, Al.armoured cable.

3.5 core x 25.0 sq. mm. XLPE, Al.armoured cable.

3.5 core x 50.0 sq. mm. XLPE, Al.armoured cable.

3.5 core x 300 sq. mm. XLPE, Al.armoured cable.

3 core x 6 sq. mm. XLPE, Al.armoured cable.

Supplying of following 1100 volt grade XLPE insulated PVC inner sheathed and FRLS PVC outer sheathed Copper conductor armoured/Flexible cables as per specification. 1 core x10 sq. mm. XLPE CU. Flexible cable.

UPS: 7.5 KVA ON LINE UPS with 15 min battery backup of 1 phase input & 1 phase output .Sine Wave Inverter Capacity 7.5 KVA, Rated Power 6400 W Supports Eight battery 24 Month Warranty Safe for sensitive appliances with Sine wave out-put Cruze HKVA Inverters can run heavy loads like AC, Geyser, Petrol Pumps, Photocopiers, Dental Chairs etc., depending on their capacity (please check the inverter capacity and your power requirement) Auto over-load handling capacity Installation and maintenance friendly Offers high quality and reliable power back-up solution for office and homes MCB for protection from Input mains Bypass switch for supplying output directly from grid in case of Home UPS fault. Noiseless Operations with the help of low harmonic distortion Intuitive Display to easily understand status of mains availability, battery status, etc. Comprehensive protection against short-circuit, reverse polarity, battery over-charge, deep-discharge etc Adaptive Battery charging control system technology (ABCC) ensures faster battery charging and enhances battery life by around 70% Supports a wide battery range, i.e. Flat Plate, Tubular & VRLA (SMF)

Supply and fixing in position 1000 mm wide rubber matting of 1100 volts grade as per electricity rules (exact length rubber mats to be worked out as per site requirement). Thickness of rubber mats shall be not less than 6 mm.

Providing and fixing steel structure work for supporting UPS & battery cabinets.

Installation, testing and commissioning of ceiling fan,wiring the down rods of standard length (upto 30 cm) with 1.5 sq. including mm FR PVC insulated, copper conductor, single core cable,including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor,single core cable and earthing etc. as required.

24" dia sweep wall bracket fan (BEE 5 star rated) of approved make complete with all accessories.

48" dia sweep ceiling fan (BEE 5 star rated) of approved make complete with all accessories.

8" dia sweep toilet exhaust fan of approved make complete with all accessories.

DG SET Design, Manufacture, Supply, erection, testing and commissioning of 160 kVA, 415V, 3 Phase, 4 Wire, 50 Hz at 0.8 p.f. prime continuous (actual) rating radiator cooled diesel generating set in acoustic enclosure with radiator, Water cooled engine, PMG, base frame, Alternator, Static Excitation System, Lube Oil System, Electronic Governor, 24V Batteries & Battery Charger, Instrumentation, day oil fuel tank, Residential Silencer with Bellows, Alarms, microprocessor based Engine Control Panel, AVR Panel ,equivalent for AMF facility, termination adopter box suitable for XLPE insulated aluminium cables, drip trays space for mounting all associated equipments/ works as per specification including providing common base plate, anti vibration isolators, foundation bolts etc. The civil works for foundation for D.G.Set shall not be included in the rate. But other accessories like grouting screws, anti-vibration pads etc. shall be included in the rate. Alternator shall have class H insulation and rated for 100 KW output at 50°C. Emergency stop push button for individual DG set shall be located at the exit door. Engine shall not be derated upto 50 deg.C ambient. Note: Piping between day oil tank & DG set shall be included.

Providing & fixing ABC type (Dry powder type ) extinguishers. Including all accessories as per IS specification (IS :15683) Consisting of welded MS cylindrical body with discharge hose ,discharge valve ,suspension brackets,initial filling etc. complete as required., initial filling etc complete as required. Capacity - 6 kg

U-shape Customized Conference table make with wooden modety and top and Mica finish on the top and edges of the table moulding.Supply & Placement of 25 seater Modular Conference table as per the layout having worksurface made of top thickness 37.6 (18mm + 18mm + 0.6 mm DL + 0.4mm Membrane) Edge profile Waterfall Edge 10mm radius on top edge and 5mm at bottom. legs & modesty panel made from 36mm PPB (18+18) having a straight profile with half round edges and clad with 0.6mm thick Post Forming laminate. Overall thickness of leg is 37.2mm. Made from PLT (Prelaminated Twin) boards of 18mm thick. Made from 0.6mm thick CRCA painted. Made of 12mm thick. MDF Painted all over. PVC Membrane foil (0.4mm thick) clad on the substrate MDF using PU glue. This foil is pre-coated with layer of polyurethane for better scratch resistance. Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015.

Executive Revolving Chair-Hi-Back Executive Chair should have pneumatic seat height adjustment facility. Height of the chair should be atleast 97cm. Depth and width of the chair should be at least 76cm. Seat height should be at least 54cm.Back size-47.5cmWx58cmH. The seat and back should be made up of 1.2±0.1 cm thick hot pressed plywood upholstered with fabric upholstery cover and moulded polyurethane foam .The back Foam should be designed with countered lumbar support for extra comfort. The High resilience polyurethane Foam should be moulded with density=45±2kg/m3 and hardness load 16±2 kgf. The armrest should be injection moulded from black Co polymer polprylene. It should have centre tilt mechanism with tilt tension adjustment, upright position locking, 360 degree revolving and seat back tilting ratio should be 1:3.The pedestal should be injection moulded in black 33% glass filled Nylon-66. The pedestal should also have 5 nos twin wheel castor. The seat end of the chair towards the legs should have a appearance as of waterfall edge. Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015 & AIOTA.

Chair should have pneumatic seat height adjustment facility. Height of the chair should be atleast 97cm. Depth and width of the chair should be at least 76cm. Seat height should be at least 54cm.Back size-47.5cmWx58cmH. The seat and back should be made up of 1.2±0.1 cm thick hot pressed plywood upholstered with fabric upholstery cover and moulded polyurethane foam .The back Foam should be designed with countered lumbar support for extra comfort. The High resilience polyurethane Foam should be moulded with density=45±2kg/m3 and hardness load 16±2 kgf. The armrest should be injection moulded from black Co polymer polprylene. It should have centre tilt mechanism with tilt tension adjustment, upright position locking, 360 degree revolving and seat back tilting ratio should be 1:3.The pedestal should be injection moulded in black 33% glass filled Nylon-66. The pedestal should also have 5 nos twin wheel castor. The seat end of the chair towards the legs should have a appearance as of waterfall edge. Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

3+3 Seater Sofa Specification- Size- H- 840 mm, L- 1880 mm, D- 815 mm. Structure made of Pine Wood, fitted with 50mm wide rubberized belts 50mm wide with 28 density U foam as per design, Upholstered with premium quality PU cloth/Leatherite with help of stitching, where ever necessary. Handle made of MDF Board With PU Paint. The overall appearance of the product shall be as per photograph.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

Wooden Centre Table Glass Top- Overall Size: 1200 x 600 x 450 mm Legs shall made out of 7 5 x7 5 mm teal rood section as per photograph. Top rail shal1 be ma de of 7 0x22mm as per photograph. Top shall be made of 18mm veneer faced MDF board. Teak wood beading of 18mm shall be fitted as per approval. Polish- PUpolish shall be done. The overall appearance of the product shall be as per photograph.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

Wooden SIde Table Glass Top- Overall Size: 600 x 600 x 450 mm Legs shall made out of 7 5 x7 5 mm teal rood section as per photograph. Top rail shal1 be ma de of 7 0x22mm as per photograph. Top shall be made of 18mm veneer faced MDF board. Teak wood beading of 18mm shall be fitted as per approval. Polish- PUpolish shall be done. The overall appearance of the product shall be as per photograph.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

2+2 Seater Sofa Specification- Size- H- 840 mm, L- 1400 mm, D- 815 mm. Structure made of Pine Wood, fitted with 50mm wide rubberized belts 50mm wide with 28 density U foam as per design, Upholstered with premium quality PU cloth/Leatherite with help of stitching, where ever necessary. Handle made of MDF Board With PU Paint. The overall appearance of the product shall be as per photograph.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

CENTER TABLE -Wooden Centre Table Glass Top- Overall Size: 1200 x 600 x 450 mm Legs modesty made by MDF board. Top rail shal1 be ma de of 7 0x22mm as per photograph. Top shall be made of 18mm veneer faced MDF board. Teak wood beading of 18mm shall be fitted as per approval. Polish- PUpolish shall be done. The overall appearance of the product shall be as per photograph.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

ROUND CAFETERIA TABLE WITH CHAIR-1+3-The table should be make with 3 layer pre laminated particle baord with melamine finish dia-900x900mm, with water resistant and termite proof ,top shall be 18mm thick density board ,Legs should be powder coted die cast 50micron .The cahir should be make with structure with solid wood and fabric or best quality PU leathrette finish seat and back.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

SQAURE CAFETERIA TABLE-1+2-The table should be make with 3 layer pre laminated particle baord with melamine finish dia-900x900mm, with water resistant and termite proof ,top shall be 18mm thick density board ,Legs should be powder coted die cast 50micron .The cahir should be make with structure with solid wood and fabric or best quality PU leathrette finish seat and back with the samll and elegant look handle provide which is given very comfortable for seating.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

6 SEATER DINING TABLE-The table make and finish with high gloss polish and structure should be solid wood Sheesham,Size should be-1800mmx 900mmx 750mm,Table top thickness should be 20mm and legs are also make by sheesham wood,Chair make and design by as per seating convinent and structure should be solid sheesham wood with high gloos polish.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

4 SEATER DINING TABLE-The table make and finish with high gloss polish and structure should be solid wood Sheesham,Size should be-1200mmx 750mmx 750mm,Table top thickness should be 20mm and legs are also make by sheesham wood,Chair make and design by as per seating convinent and structure should be solid sheesham wood with high gloos polish.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

KING BED-78'' X 72''The structure will be made of particle board with 18mm thickness head board, foot board,side panels and top. Size of the bed will be 78 X 72 inches.Head board height will be 36 inches.Edge banding will be done on edges of the board with 2 mm thickness on the visible parts and 0.8mm on the non visible sides.Minifix dowels must be of german made.Adjustment labeller and bed clamp will be fitted.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

BED SIDE TABLE-16'' X 16'' The structure will be made of particle board with 18mm thickness head board, foot board,side panels and top. Size of the bed will be 16 x16 inches.Minifix dowels must be of german made.Adjustment labeller and single drawer will be fitted.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

ASTRA PUF-72''X78''X6''-quilting for comfortable surface feel. Underneath are pocket springs, which are best for supple support and which also entirely eliminate partner disturbance. Premium Jacquard fabric gives it a smooth finish and soft top feel. Foam wall technology prevents side sagging and gives a more comfortable sitting experience. Bottom airmesh fabric improves ventilation. Neem Fresche® provides germ protection.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 9001 CERTIFIED.

WARDROBE MAKE WITH PLPB BOARD SIZE-36''X78''The structure will be made of particle board with 18 mm thickness.Edge banding will be done on edges of 2mm on visible sides and 0.8mm on non-visible sides. Wardrobe size will be 78X36 inches with one drawer.Hardware must be of German made,which include one drawer lock,three handles,One wardrobe shutter lock,two set hings,one wardrobe shutter lock.Aluminium hanger rod and adjustment leveller will be given.Shutters,side panels,partition panels and bottom will be of 18 mm thickness with edge banding.the back panel will be of 9 mm thickness.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

TV UNIT make with plpb board -60''x17''x16''FIXED IN A WALL,TV UNIT make with plpb board -60''x17''x16''FIXED IN A WALL,The wall uni make with three layer pre laminated particle board with 25mm thick board and side modesty should be 18mm thick ,4 drawer on the both the side of the unit,Wall unit should be fixed in a wall with channel hanging.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

VIP SUITE ROOM-1 &2 KING BED WITHOUT STORAGE-78''X72''The structure will be made of particle board.The side panels,top and bottom panels will be of 18 mm thickness and head board and foot board will be of 25 mm thickness. Edge banding will be done on edges of 2 mm on visible sides and 0.8 mm on non-visible sides.Size of the bed will be 78X72 inches.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

BED SIDE TABLE-16'' X 16'' The structure will be made of particle board with 18mm thickness head board, foot board,side panels and top. Size of the bed will be 16 x16 inches.Minifix dowels must be of german made.Adjustment labeller and single drawer will be fitted.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

ASTRA PUF-72''X78''X8''quilting for comfortable surface feel. Underneath are pocket springs, which are best for supple support and which also entirely eliminate partner disturbance. Premium Jacquard fabric gives it a smooth finish and soft top feel. Foam wall technology prevents side sagging and gives a more comfortable sitting experience. Bottom airmesh fabric improves ventilation. Neem Fresche® provides germ protection.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 9001 CERTIFIED.

HI-BACK ROOM CHAIR-Chair should make with High density foam and Fabric should be as per buyer choice, Size should be 27'' x 26'' x 36'',under the structure should be sheesham wood and legs are wooden with melamine finish.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

CUSTOMIZED WARDROBE AS PER LAYOUT- Customized wardrobe should be make with mica and ply finish .Size should be as per actual measurement.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

TV UNIT make with plpb board -60''x17''x16''FIXED IN A WALL,The wall uni make with three layer pre laminated particle board with 25mm thick board and side modesty should be 18mm thick ,4 drawer on the both the side of the unit,Wall unit should be fixed in a wall with channel hanging.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

Study Table with single drawer.-1200x600x750 and SINGLE STUDY CHAIR,providing and fixing standard office table of Dimension-1380 X 690 X 720. Strong sturdy desk which can stand alone or be connected to or joined together to build desking systems.This table is a simple built table sturdy can be used for a variety of operations like a writing desk.The desk is fully pre-laminated particle board melamine finish and smooth liping table is surely lasts long due to its scratch resistant and water resistant ,stain proof and easy maintain spotless cleaning.These are fully (100%) melamine finish.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

LSHAPE SOFA SET AS PER BUYER CHOICE WITH PUFFY,Sof aset make with high density foam used in a seat and back with fiber cushion ,understructure should be wooden and legs should be SS304,Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

CENTER TABLE MARBLE TOP,Cenetr table top should be composite marble and side panel should be Doco finish MDF baord ,thickness of the side panel should be 15mm and legs should be boil processed ruber wood,ther are 2 drawer on both the side of the table and small cabinet on the both sid eof the table.

6 SEATER DINING TABLE-6 SEATER DINING TABLE-The table make and finish with high gloss polish and structure should be solid wood Sheesham,Size should be-1800mmx 900mmx 750mm,Table top thickness should be 20mm and legs are also make by sheesham wood,Chair make and design by as per seating convinent and structure should be solid sheesham wood with high gloos polish.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

CONSOLE TABLE -The table make and finish with high gloss polish and structure should be solid wood Sheesham,Size should be-1500mmx 450mmx 825mm,Table top thickness should be 20mm and legs are also make by sheesham & Mosaic put on the boarder of the table.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

SECURITY TABLE -900X600 WITH 1 FIXED DRAWER-1200x600x750 and SINGLE STUDY CHAIR,providing and fixing standard office table of Dimension-1380 X 690 X 720. Strong sturdy desk which can stand alone or be connected to or joined together to build desking systems.This table is a simple built table sturdy can be used for a variety of operations like a writing desk.The desk is fully pre-laminated particle board melamine finish and smooth liping table is surely lasts long due to its scratch resistant and water resistant ,stain proof and easy maintain spotless cleaning.These are fully (100%) melamine finish.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

MID BACK REVOLVING CHAIR -Chair should have pneumatic seat height adjustment facility. Height of the chair should be atleast 97cm. Depth and width of the chair should be at least 76cm. Seat height should be at least 54cm.Back size-47.5cmWx58cmH. The seat and back should be made up of 1.2±0.1 cm thick hot pressed plywood upholstered with fabric upholstery cover and moulded polyurethane foam .The back Foam should be designed with countered lumbar support for extra comfort. The High resilience polyurethane Foam should be moulded with density=45±2kg/m3 and hardness load 16±2 kgf. The armrest should be injection moulded from black Co polymer polprylene. It should have centre tilt mechanism with tilt tension adjustment, upright position locking, 360 degree revolving and seat back tilting ratio should be 1:3.The pedestal should be injection moulded in black 33% glass filled Nylon-66. The pedestal should also have 5 nos twin wheel castor. The seat end of the chair towards the legs should have a appearance as of waterfall edge. Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

LOBBY SOFA SET-TWO SEATER Sofa Specification- Size- H- 840 mm, L- 1680 mm, D- 815 mm. Structure made of Pine Wood, fitted with 50mm wide rubberized belts 50mm wide with 28 density U foam as per design, Upholstered with premium quality PU cloth/Leatherite with help of stitching, where ever necessary. Handle made of MDF Board With PU Paint. The overall appearance of the product shall be as per photograph.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

Side Table make with WOODEN STRUCTURE AND GLASS TOP-Wooden SIde Table Glass Top- Overall Size: 600 x 600 x 450 mm Legs shall made out of 7 5 x7 5 mm teal rood section as per photograph. Top rail shal1 be ma de of 7 0x22mm as per photograph. Top shall be made of 18mm veneer faced MDF board. Teak wood beading of 18mm shall be fitted as per approval. Polish- PUpolish shall be done. The overall appearance of the product shall be as per photograph.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

CENTER TABLE TOP SHOULD BE GLASS TOP NAD STRUCTURE WOODEN-Wooden Centre Table Glass Top- Overall Size: 1200 x 600 x 450 mm Legs shall made out of 7 5 x7 5 mm teal rood section as per photograph. Top rail shal1 be ma de of 7 0x22mm as per photograph. Top shall be made of 18mm veneer faced MDF board. Teak wood beading of 18mm shall be fitted as per approval. Polish- PUpolish shall be done. The overall appearance of the product shall be as per photograph.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

COFFEE TABLE WITH 2 CHAIR--1+2-The table should be make with 3 layer pre laminated particle baord with melamine finish dia-900x900mm, with water resistant and termite proof ,top shall be 18mm thick density board ,Legs should be powder coted die cast 50micron .The cahir should be make with structure with solid wood and fabric or best quality PU leathrette finish seat and back with the samll and elegant look handle provide which is given very comfortable for seating.Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

TERRACE OUT DOOR -4+1 TABLE & CHAIR SET,Structure and material should be PVC rattan water proof any weather damage free,The wicker are make with nylon with PVC which very strong and free of damage.legs should be round tubular powder coating ,Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

2ND FLOOR BALCONY COFFEE TABLE SET-2+1-Structure and material should be PVC rattan water proof any weather damage free,The wicker are make with nylon with PVC which very strong and free of damage.legs should be round tubular powder coating ,Manufacturer should be a certified member of BIFMA & following management system as per, ISO 18001:2007, ISO 14001:2015, ISO 9001:2015,BIFMA Lavel-1,2,3,IGBC ,Green Guard & AIOTA.

ROLLER BLINDS-The ultimate in privacy, light control & insulation, blockout fabrics are ideal for bedrooms and media rooms, providing both daytime and nightime privacy,Minimum width: 250 mm (chain driven); 570mm (motorised)Minimum drop: 300 m,Maximum width: 3000* mm Maximum drop: 3000 mm, Quote only for Estimate final quote we will provide as per measurement of the site.

SITC of fixed dome indoor Colour Varifocal Lens Camera having 0.20 lux level requirement in night mode with the following components/ sub assemblies as per specifications, complete with power supply unit, necessary brackets for fixing in the false ceiling etc. as required.(The camera shall be UL/EN/FCC certified) a. 1/3" progressive scan CCD image sensor Day/Night camera with in built DSP, advanced features like High resolution of minimum 640 x 480, AGC, BLC, extended sensitivity, support on screen display etc. b. 1/3" Image format varifocal lens (4 to 8 mm)

SITC of Advanced dynamic 16 channel digital event recording system with Digital multiplexer, DVR, Video Motion Detection & Video management System features suitable for CCTV cameras and as specified in the technical specifications inclusive of the rack cost and inclusive of 1.5 TB storage Memory for 12.5 frames second at 4CIF (704 x 576) resolution, TCP/IP connectivity, dual streaming and H.264

SITC of Advanced dynamic 8 channel digital event recording system with Digital multiplexer, DVR, Video Motion Detection & Video management System features suitable for CCTV cameras and as specified in the technical specifications inclusive of the rack cost and inclusive of 1.5 TB storage Memory for 12.5 frames second at 4CIF (704 x 576) resolution, TCP/IP connectivity, dual streaming and H.264

SITC of coaxial FRLS RG 6 cable for CCTV system

SITC of 2C x 1.5 sq mm FRLS cable

SITC of cam power supply

Supply & Installation of suitable stand for monitor of CCTV

Supply, Installation and Commissioning of CCS 1000 D Digital Discussion System With DAFS and Recorder Features: 1. Excellent speech intelligibility with built-in Digital Acoustic Feedback Suppression 2. Built-in audio recording on internal memory and/or USB memory stick 3. Native support for automatic HD camera control 4. Advanced configuration and control via built-in web browser 5. “Energy saving mode” for automatic switch-off after two hours of inactivity

Supply, Installation and Commissioning of CCS1000 Controller with Digital Acoustic Feedvback Supressor

Supply, Installation and Commissioning of 240 Watts mixer Amplifier. Features: 1. 4 microphone / line inputs, plus music source input 2. Announcement only output, 3‑wire volume override 3. Wide range of output power (60, 120 and 240 Watts) 4. 2‑tone chime

Supply, Installation and Commissioning of Handeld Wireless Microphone

Supply, Installation and Commissioning of 10 meter Extention cable

Supply, Installation and Commissioning of Speaker Wire

Supplying with installation testing and commissioning of Hi -- wall 5 STAR rating non ducted split type air conditioner of the following capacity with cordless remote complete with indoor and outdoor unit, copper pipe and electrical connection up to 5 m between the room unit and out door unit as approved by the Deptt.) and as directed by the department. a) 2 Ton Capacity

Supplying with fitting and fixing Voltage stabilizer of the following specification complete including making necessary connection as approved, specified and directed by the deptt. 5.0 KVA Automatic Input 130V Out put 200-240 V

Outdoor Angle

Installation of Split Ac

J C Infra corporation Limited