Construction of Proposed Eco log lodge bridge /Amphitheater/ Toilet Block including water supply and sanitary works for proposed Tourist facilitation centre at Salamabad Uri

Amount

Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil

Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with: Cement mortar 1:6 (1 Cement : 6 coarse sand)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Supply and Filling with Nallah muck in layers including watering, compacting and dressing under flooring in ground floor etc including all cost and carriage complete.

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in :(Cement mortar 1 :6 (1 cement : 6 coarse sand)

Half brick masonary with common burnt clay F.P.S ( non modular) brick of class designation 75 in superstructure above plinth level upto floor V level: 1:4 (1 cement 4 coarse sand)

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

15mm cement plaster on the rough side of single or half brick wall of mix 1:6 (1 cement: 6 fine sand) (including cost of all material, leads, lifts and carriages etc upto site of work complete).

6-mm thick cement plaster on ceilings, plinth etc. in (1 cement: 6 fine sand mix). Upto floor V level complete in all respects (including cost of all material, leads, lifts and carriages etc. upto site of work complete).

Centering and shuttering including strutting, propping etc. and removal of form for : A). Suspended floors, roofs, landings, balconies columns, plinth beam and access plateform.

B). Foundations, footings, base of columns etc plinth beams, and access platforms.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete below/above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing of U-PVC sliding/casement/fix window in white colour,frame 60mm thick (min) x 45mm (min) with 1.5 mm GI reinforcement sash 39mm (min) 58mm (min) with 1.25mm GI U section reinforcement with rubber gasket of grey / black colour 10 years warranty against weathering of profile with complete hardware fittings and with 5mm thick toughened glass and fiber jalli option pre- febricated on german fabrication system( mosquito sash 18mm(min) x 43mm(min)(with welled cornes) complete at site (for glazing/wire guage shutters)

Providing wood work using First class deodar wood in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately)

Providing and fixing ISI marked flush door shutters (35mm thick) conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws

Providing and fixing panelled or panelled and glazed shutters using first class kail wood 35 mm thick for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately).

Providing and fixing wire gauze shutters of First class kail wooden 35 mm thick using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge.

Providing and fixing 4mm thick panels of plain glass for fixed glazing panels/ shutters (only panel area to be measured) including cost of teak wood beadings of required size complete

Applying priming coat with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture coat with ready mix paint of approved brand and manufacture on wood work etc including cost and carriage of all materials equipments complete job as per drawings, specifications and as directed by the engineer Incharge.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing hardware fittings (anodized aluminium) of approved brand and of required type as approved by Engineer incharge. complete as per the specifications

Tower bolts 100mm (windows)

Handle 100mm (window)

I-Hooks 150mm

L-drop 250mm

Tower bolts 150mm (doors)

Handle 125mm (door)

butt hinges of 100x63x3.2 mm

butt hinges of 125x75x4 mm

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing machine cut, mirror / egg shell polished , Marble stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. All complete as per Architectural drawings, and as directed by the Engineer- in-Charge. a. 18 mm thick Italian Marble stone slab, Perlato, Rosso Verona, Fire Red or Dark Emperadore etc

Providing and fixing 1st quality Vitrified Double Charged tiles in floor/skirting etc. of standard thickness of approved make in all colours, shades, design and prints as approved by the engineer-in-charge over 12 mm thick bed of cement mortar 1 : 3 (1cement 3 coarse sand) and jointed with grey cement slurry @ 3.3 kg per Sqm. Including pointing in white cement mixed with pigment of matching shade with all lead, lift, labour, materials, tools, plants complete as per specification and as directed by Engineer in Charge .(600x600mm)

Providing and fixing 1st quality ceramic glazed floor tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Chequerred terrazo tiles 22mm thick with graded marble chips of size upto 6mm in floors jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand)Light shade using white cement

Kota stone slab flooring 25 mm thick over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing, polishing and curing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand)

Kota stone slab 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm ( average) thick cement mortar 1:3 (1 cement:3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing, polishing and curing complete.

50mm thickCement concrete flooring 1:2:4 ( 1 cement: 2 coarse sand . : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.

Providing and fixing devri stone clading 25 mm thick with exposed face fine dressed with rough backing on wall lining etc. upto 10 meter ht back filled with a grout of 12 mm thick cement sand mortar in 1:3 (fine cheiseled)including pointing in white cement 1:2 with admixture of pigment matching to stone (For plinth)

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with coarse sand etc. all complete as per direction of Engineer-in-charge.

Providing and applying white cement based putty of 2 mm thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall / ceiling Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 liter/10sqm) over and including base coat of exterior primer applied @ 2.20kg/10sqm

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with Armourcrete of M/s The Structural Water Proofing Company Pvt. Ltd. Or Tapecrete of M/s CICO Technologies Ltd. consisting of applying : First layer of slurry of cement @ 0.488 kg/Sqm mixed with Armourcrete or Tapecrete @ 0.253 kg/Sqm. This layer will be allowed to air cure for 4 hours. Second layer of slurry of cement @ 0.242 kg/Sqm mixed with Armourcrete or Tapecrete @ 0.126 kg/Sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (The rate includes supply of waterproofing compound, preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry)

Providing and fixing plain eves boarding (300mm x 40mm ) 2nd class kail wood fixed with screws etc, including all carraiges .All job completed

P/F of 20 mm thick T&G well planned planks for roof soffits & Ceiling on wood work in false ceiling, partitions sawn and put up in position of Budloo wood (Ceiling Joists) which shall be paid for separately, including cost of necessary adhesive & cost of nails etc. with necessary cornice of required size complete job. all complete as approved by Engineer-in-charge (including cost of all material, leads, lifts and carriages etc upto site of work complete). (soffits of Ist Class Kail Wood).as per the directions of Consultant/as per the drawings enclosed

Structural steel work in Welded built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing 16 mm dia mild steel round holding down bolts 500 mm long with nuts and washer plates complete for holding steel trusses.

ACCESSORIES Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm)

Providing valleys of 90cm wide overall in plains G.S. sheets fixed with polymer coated J. or L. hooks, bolts and nuts 8 mm dia G I. limpet and bitumen washers complete.1.60mm thick with zinc coating not less than 350gm/m2 (North light curves)

Providing and fixing precoated galvanized iron profile sheets (size,shape & pitch of corrugation as approved by Engineer I/C) 0.50mm + 0.05% ) total coated thickness with zinc coating 120 grms per sqm as per IS 277, in 240MPA steel grade, 5-7 microns epoxy primer on both sides of sheet & polyester top coat 15-18-microns. sheet should have protective guard flim of 25-micron minimum to avoid scratches during transporatation in single length upto 12 mtr or as desired by Engineer I/C . The sheet shall be fixed using self drilling/ self tapping screws of size (5.5x55mm )with EPDM seal, complete upto any pitch in horinzental/ vertical or curved surfaceses, excluding the cost of purlins, rafters & trusses & incl. cutting to size and shape whereever required.

Providing and Fixing of 50mm dia stainless steel railing of 304 grade of hallow tube 1.6 mm thick of Jindal/Salem make or equivalent including welding and fixing with stainless steel machine screws for making required size and shape, buffing etc. Complete and fixing stainless steel balusters upto 900 mm height, newel post 1050 not less then hight 1050mm and S S tubes, three in one installed horizontally including cutting, welding, grinding to required shape and size by required steel dash fasteners, nuts, bolts, screws ,etc. in floors and treads including providing SS shoe at each balusters complete as per architectural drawings and as per the directions of engineer incharge including cutting of granite/marble floors and fastening with lead grouting if required, complete in all respects.

Providing & fixing of stainless steel nevel post (Ornamental ) including top ball of AISI 304 grade of required height duley anchored to floor with dash fasteners . Height of the nevel post shall not be less than 1050 mm above the finished skirting level all complete as per architectural drawings (including cost of all material, leads, lifts and carriages etc upto site of work complete).Complete as per the directions of Engineer incharge.

Providing and fixing Almirah/ kitchen counters 750 mm high x 600 mm deep(min) made up of 19 mm thick ply board for frames, shelves and 12 mm thick ply board for drawers with 19 mm thick ply board shutters finished top with granite / dulmica 0.80 mm thick as per requirment on on exposed surfaces fixed with adhesive/ screws/ nails wherever required including inside painting on exposed surfaces including telescopic channels ,drawer knobs locks and all necessary fittings of Ist Quality as required all complete as per the directions/instructions of Engineer in charge.

Providing and fixing Reception desk 900 mm high x 600 mm deep(min) made up of 19 mm thick ply board for frames, shelves and 12 mm thick ply board for drawers with 19 mm thick ply board shutters finished top with 1mm thick laminated teak wood on exposed surfaces fixed with adhesive/screws/nails wherever required including inside painting on exposed surfaces including telescopic channels ,drawer knobs locks and all necessary fittings of Ist class Quality as required all complete as per the directions/instructions of Engineer in charge.Complete job in all respects.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 MM SAND cast iron P or S Trap,10 liter low levelwhite P.V.C Flushing Cistern,including flush pipe,with manually controlled device(handle Lever),with all fittings and fixtures complete,including cutting and making good the walls and floors wherever required. (White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.)

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I. clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: Range of four urinal basins with 10 liter white P.V.C automatic flushing cistern..

Providing and fixing Urinal Partition/Division Plate

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass Centre Hole Basin Mixer(01 Nos), 32 mm C.P. brass waste of standard pattern(01 Nos), Pedestal (01 Nos) including painting of fittings and brackets, cutting and making good the walls wherever required.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 510X1040MM BOWL DEPTH 250MM

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing. Rectangular shape 453x357 mm

Providing and fixing toilet paper holder with Flap made out of C.P Brass

Providing and fixing C.P Brass Soap Dish.

Providing and fixing health faucet with hose pipe for european water closet complete in all respect of approved quality

Providing and fixing CP brass towel rail complete with CP brackets fixed to wooden cleats with CP brass screws.

Providing and fixing C.P brass bib cock with Auto closing System with Built in control Cock with Wall Flange of approved quality 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser/cisterns points. 15 mm nominal bore

Providing and fixing C.P. brass Single Lever Basin Mixer with 450 mm braided connection pipe. 15 mm nominal bore

Providing and fixing C.P. brass bottle trap for wash basin including CP waste fittings complete 32 mm dia complete in all respect of approved quality.

Providing and fixing C.P. brass Wall Mixer

Providing and fixing PP Based soil, waste and vent pipes (Silencio as per DIN4109) suitable to rubber ring joints , which includes bends, rubber ring, jointing, junctions, clean out plug , cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design .etc. complete including jointing.

110 mm dia. PP SWR socketed pipe with rubber ring joints .

75 mm dia. PP SWR socketed pipe with rubber ring joints .

160 mm dia. PP SWR socketed pipe with rubber ring joints.

Providing and Fixing of Floor Traps 110 mm with double chrome plated Cover one Grated and one closed and all other fittings required.

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer in charge.Concealed work, including cutting chases and making good the walls etc

1620 (20 mm OD) pipe

2025 (25 mm OD) pipe

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer in charge.Internal work (Exposed on wall)

2532 (32 mm OD) pipe

4050(50 mm OD) pipe

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer in charge. A). 4050 (50 mm OD ) pipe

Providing and Fixing of Thermal Insulation for Hot Water Lines made out of Flexible Elastomeric Foam of Closed Cells Structure Having a Thermal Conductivity of 0.038 W/m.K at 200 Deg C water Vapour Permeability of Cu.m 5000 as Required including accessories i.e Adhesives/Tape on all Joints as per the satisfaction of the Engineers Incharge. A). 1620 (20 mm OD) pipe

Providing and fixing unplasticised PVC connection pipe with brass unions: A). 45 cm length (15mm nominal bore)

Cutting holes upto 30x30 cm in walls including making good the same with common burnt clay F.P.S.(non modular) bricks

Constructing masonary chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement: 4 coarse sand) with C.I. surface box 100x100x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cenment:5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design With F.P Bricks.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m(For All Kinds of Soil)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m

Providing and fixing PP Based soil, waste and vent pipes (Silencio as per DIN4109) suitable to rubber ring joints , which includes bends, rubber ring, jointing, junctions, clean out plug , cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design .etc. complete including jointing.for Under Ground Sewage System in the Existing Excavated Trench.

A). 110 mm dia. PP SWR socketed pipe with rubber ring joints .

B). 160 mm dia. PP SWR socketed pipe with rubber ring joints.

Providing and filling sand of grading zone V or coarser grade all-round the Composite Pipes in external work & lay dry brick over sand layer to protect the pipe.

110 mm dia. PP SWR socketed pipe with rubber ring joints

160 mm dia. PP SWR socketed pipe with rubber ring joints.

Supply, Installation of PVC Gully Trap of Size 110 mm Makes:-Astral/SFMC/Finolex

Making soak pit 2.5 m diameter 3.0 metre deep with 45x45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8 long complete as per standard design. With F.P.S. bricks

Constructing septic tank, of size 5.0mx2.5mx1.4m approx. height(Height to be fixed as per site requirement i.e. below invert level of last manhole (1.5 m water depth) , in B/W, 350/230 mm thick ( minimum) walls and 400 mm

Providing & fixing full way lever operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not less than 16 Kg / sqcm with threaded / flanged joints complete with nuts, bolts, gaskets, washers etc.

50 mm Diameter

32 mm Diameter

25 mm Diameter

Providing and fixing on wall 35 Ltrs Electric Geyser with ABS Body. Venus/racold make

Providing and placing on terrace (at all floor levels) 2000 Ltrs capacity polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank.

M/S ALTAF CONSTRUCTIONS