Proposed Construction of Jharkhand Guest House at Puri Odisha

WATER PROOFING WORK

Waterproofing treatment for Raft- Supply & Application of membrane HDPE-P: Supplying and installing waterproofing treatment by using 1.2mm thick fully bonded pre applied HDPE using Fosroc or equivalent approved make Membrane HDPE-P with a film of pressure sensitive adhesive and allows poured concrete to bond fully with the membrane on Raft Slab/Stitch Slab/footing/Grade slab as shown in drawing. The waterproofing membrane shall comply with BS 8102 - 2009 for grades 1, 2 and 3 and Indian Standard 16471 : 2017 for Protection of structures against water from the Ground.

Waterproofing membrane shall be supplied with side overlaps of 75mm provided on the self-adhesive selvedge and end laps using HDPE P Sealed tape of 100mm wide. Membrane shall be installed in strict accordance with the manufacturer’s instructions with and shall provide an intimate bond to resist water migration. The fully bonded HDPE membrane is loosely-laid on the PCC before casting of the RCC raft slab / Footings/Stitch Slab/as shown in drawings or wherever applicable etc. The membrane waterproofing shall taken to the height of grade slab concrete in aid of shuttering sheets or block work over and above lapping with Retaining wall waterproofing system The fully bonded Pre applied HDPE sheet waterproofing membrane shall have following typical properties:

1) Membrane thickness: 1.2mm 2) Bare HDPE film thickness: 0.9mm 3) Tensile strength (film) : >27 Mpa (ASTM D412) 4) Elongation >500% 5) Peel adhesion to concrete: > 1500N/m (ASTM D 903 Modified) 6) Puncture Resistance: >1000N + 5% (as per ASTM E154) 7) Resistance to hydrostatic pressure: >70m (ASTM D751-06) 8) Low temperature flexibility: <-25°C, no crack 9) Linear Dimensional change: 0.1% (ASTM D1204) 10) UV Exposure test 45 day: No change (ASTM G153) 11) Lap joint strength: 1500 N/m (ASTM D1876)

Membrane Installation – Vertical Raft application •The Fosroc or equivalent approved make membrane HDPE-P Membrane shall be terminated over the outer surface of the vertical wall of the Raft by cutting a groove of 10mmX10mm the membrane will be fixed inside the groove by then will be sealed by Cementitious micro concrete Renderoc RG/Polymer modified mortar Renderoc SP40. • End joints and cut edges –The HDPE-P Membrane shall be terminated over the outer surface of the vertical wall of the Raft by cutting a groove of 10mmX10mm the membrane will be fix inside the groove by aluminium strip and then will be sealed by Epoxy mortar Nitomortar S. Place the consecutive membrane (SBS Membrane) edge on the HDPE-P membrane by providing a overlap of 150 mm and rolled out properly. The item rate shall include base preparation which include wire- brushing the Concrete/Masonry surface & cleaning with air jet, treating all joints, cracks, honeycombs on the RCC members as per manufactures specification and approved methodology. Item rate also include cost of all materials, miscellaneous consumables, labours, transportation of material to all required locations by approved means, Curing , tools, plant and machinery, hire and fuel charges and all other incidental charges etc.,

Waterproofing treatment Retaining Wall: Proofex primer Tack coat to be applied on the RCC surface to fill the pores so as to create an anchor for Proofex 3000V, should then be fixed on the cleaned vertical surface starting from bottom to top. Supply & applying 1.5mm thick High performance SBS modified self-adhesive waterproofing membrane with cross laminated HDPE film for retaining wall should be laid in accordance with the provisions of BS 8102: 1990. Material should comply with EN 13707:2004 and EN13969:2004. The material should have the following properties: Thickness 1.5mm Tensile Strength (BS EN 12311-1)- Longitudinal- 215N/50mm Transverse – 220N/50mm Elongation (BS EN 12311-1): Longitudinal- 324% Transverse - 238% Resistance to Hydrostatic head (ASTM D5385) – Min 60 m Water Vapour Permeability (BS EN 1931) – Impermeable to ISO 12572 •Termination on top of wall is by cutting groove of 20 mm X 20 mm with cutting machine - inserting the Proofex 3000 membrane; Nailing with Aluminium metal strip 20 mm wide and 1.5 mm thick. Nailed holes sealed with Nitoseal PU Sealant PU40. •The gap should then be filled with Polymer modified mortar Renderoc SP40 with bond coat of Nitobond EP with sand sprinkling. •The membrane should be protected with protection board/ dimple board (8 mm) prior to backfilling. •Backfilling should be done in layers. Coving: Supply of material and making of Coving of min (50x50) mm at all horizontal, vertical joints and changes of direction using polymer modified mortar Renderoc SP40

Pile Head Treatment- Providing and applying pile encapsulation to piles by providing details strips all around the pile and encasing the sides with high strength cementitious micro concrete Renderoc RG for a thickness of minimum 25mm all around and top of it. Micro concrete shall have compressive strength of minimum 50N/mm2 in 28 days. Flexural strength of 5N/ mm2 & Young’s modulus of 25KN/mm2, tensile strength of 2N/mm2 when mixed with water & casted at W/P ratio of 0.16. Diameter of the pile considered upto 1000 mm. •Pile top shall be covered with Supercast EPT (Epoxy grout) for a minimum thickness of 15mm and extend over the HDPE membrane for 50 mm from both the side of the pile periphery.

Treatment of Tie rod hole All Tie Road holes also to be filled with Conbextra Tie Rod grout

Filter media: Providing and laying of Filter media with stone crushed aggregates of 45 mm size satisfying the requirements laid down in clause 2504.2.2. of MoRTH specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment , wing wall and return wall to the full height compacted to a firm condition complete as per drawing and Technical Specification.

Waterproofing of Roof: Existing exposed cementitious surfaces need to be cleaned using a chisel, wire brush so that it can be free from algae, fungus and loose particles if any. Dust to be removed using air blower. On full dry conditions apply two (2) coats of Zydex Make ELASTOSIL - An acrylic copolymer having 75% solid content and blended with graded sand mixing with grey cement and water using flat brush. Mixing ratio will be 1 lt Elastosil+ 1 kg cement + 500 ml water. Coverage will be 1.6 to 1.8 per sqmtr. Within 3 to 5 days of 2nd coat screed concrete (grading) to be done. In screed mortar Zydex Make cement modifier Densiflex P to be mixed @ 350 ml per one bag cement. After completion of water curing the screed surface to be cut in 1.5 x 1.5 mtr panel size having groove size of 5 mm width and 20 mm depth. Further after cleaning of existing surface on dry conditions Zydex Make Zycosil+, clean water and Zycoprime solution 1:20:2 to be applied till saturation with a coverage of 23 to 25 sqmtr per 23 lt solution. Leave the surface for 1-2 days for full dryness. Next Zydex Make Elastostretch - An acrylic single component white coating system to be applied with three coats using roller/flat brush. The time gap between each coat should be min 12 hrs. Water dilution will be 20 to 25%. Coverage of Elastostretch will be 1 to 1.2 SQM per lt in 3 coats. While applying 1st coat thin fiber mess to be laid. Leave the surface for 2-3 days for air curing.

Waterproofing of Toilet: Surface Preparation: Clean all concrete surfaces free of laitance, dust, dirt, cavities, projecting nibs etc.by grinder and wire brush. Grease should be cleaned using a chemical degreaser and washed with clean water and allowed to dry. Remove all protrusions from concrete surfaces using a fine hair broom finish. Remove moss and lichen manually and treat the surface with a fungicide. Wash the surface thoroughly with clean water and allow it to dry. Standing water must be removed to prevent subsequent compromise of waterproof properties. Providing and Applying High Performance & Ultra flexible polymer modified elastomeric waterproofing membrane system Brushbond Ultraflex. For best results damp the surface before coating with Brushbond UltraFlex. After application of first coat to RCC surface, the second coat must be applied in perpendicular direction to the first coat when it has dried (approximately 5 to 6 hours at 30°C) Provide Nitobond tape /Glass fibre cloth of 45 to 60 GSM over construction joints and coving area between first and second coats of Brushbond Ultraflex. Brushbond UltraFlex conforms to the requirements of DIN 1048, Part 5, 1991, ISO 7783:2018, ASTM D412 : 2013. Brushbond UltraFlex is deemed to be suitable for use with potable water sources as tested as per USFDA CFR 175-300. Brushbond Ultraflex membrane shall achieve following properties: •Adhesion to substrate (ASTM D4541:2002): > 1.0 N/mm2 •Shore A hardness (ASTM D2240:2010): 79 •Tensile strength N/mm2 (ASTM D412-2013): >1.00 N/mm •Elongation at break (ASTM D412-2013): > 150% •Water Permeability EN12390 (part8) 2008) Negative Pressure: Nil •Water vapour transmission (ISO 7783:2018): ˷20.81 g/m2.hr •Crack bridging: (ASTM C1305): 1.0 mm •Foot traffic*: 6 hr +/- 1 hr Coverage: One 25kg pack covers approximately 16m2 at about 1.0mm thickness depending on surface conditions and water usage

Horizontal protection (Screed): Providing and applying protective screed of avg 50 mm thickness on treated waterproof area. The concrete shall be admixed with Conplast WL Xtra @ 200 ml per bag of cement, compaction, finishing surface suitably, curing, cleaning, testing etc. as per manufacturer's recommendations as directed by the Engineer. This item shall be payable only if EIC Vertical Protection (Plastering): a)For verƟcal surface, sprinkle fine aggregate aŌer the applicaƟon of second coat to get the mechanical key. b)Providing and applying average 12-15 mm thick single Coat cement sand plaster of mix raƟo 1:4 (1 cement: 4 sand) including adding Conplast WL Xtra @ 200 ml per bag of cement, finished smooth finish or as required to receive specified finish to correct line, plumb and level to the structure (As directed by EIC), etc all complete to the approval of the EIC.

Waterproofing of UGR and Overhead Tank: Surface Preparation: Clean all concrete surfaces free of laitance, dust, dirt, cavities, projecting nibs etc.by grinder and wire brush. Grease should be cleaned using a chemical degreaser and washed with clean water and allowed to dry. Remove all protrusions from concrete surfaces using a fine hair broom finish. Remove moss and lichen manually and treat the surface with a fungicide. Wash the surface thoroughly with clean water and allow it to dry. Standing water must be removed to prevent subsequent compromise of waterproof properties. Application of waterproofing layer Providing and applying two-component polymer modified cementitious coating Brushbond Aquaprotect, in two coats which is potable & hygiene waterproof coating for water retaining structures. Tested as per USFDA CFR 175-300 and DIN 1048 : Water Penetration Test. It should have the following properties: Mixed density: 1950 kg/m3, Water Permeability EN12390 (part8): Nil (part8) 2008) Negative pressure Chloride Ion penetrability as per ASTM C 1202-03: Low, Tensile strength (ASTM D 412 2.6): 0.79 MPa Adhesion strength (ASTM D 4541 1): 1.0N / sq.mm,Water vapour transmission (ASTM E 96 – 16): 48.49gm/m2/day Water Vapour diffusion resistance Equivalent Air layer Thickness (Sd) (ISO7783:2018): 0.49metres Horizontal protection (Screed): Providing and applying protective screed of avg 50 mm thickness on treated waterproof area. The concrete shall be admixed with Conplast WL Xtra @ 200 ml per bag of cement, compaction, finishing surface suitably, curing, cleaning, testing etc. as per manufacturer's recommendations as directed by the Engineer. This item shall be payable only if EIC Vertical Protection (Plastering): a)For verƟcal surface, sprinkle fine aggregate aŌer the applicaƟon of second coat to get the mechanical key. b)Providing and applying average 12-15 mm thick single Coat cement sand plaster of mix raƟo 1:4 (1 cement: 4 sand) including adding Conplast WL Xtra @ 200 ml per bag of cement, finished smooth finish or as required to receive specified finish to correct line, plumb and level to the structure (As directed by EIC), etc all complete to the approval of the EIC.

Providing mixing and applying over the finished substrate using Nitocote EP405 waterproofing lining to tanks / reservoir lining, supplied in two pack epoxy coating specifically designed for contact with potable water. The cured film shall comply with the requirements of IS: 9833 - 1981.specifically designed to provide a tough, Solvent free & Non – toxic, Impermeable, chemical resistance, corrosion resistant film and abrasion resistant lining. Adhesion with concrete should be greater than 1N/mm2 as ASTM D4541 and shall be applied over prepare substrate at a thickness of 200 micron (100micron/coat) dry film in two coats for internal sides of tank as per manufacturers specifications. The item rate shall be including of all kinds of labour, tools & tackle, machineries, lead & lift, mathadi charges, curing, wastages, consumable, cleaning, shifting of debris outside the site premises, etc. complete as per design, drawing & instructions of EIC.

Exposed decorative brick masonry: Providing and constructing exposed decorative reinforced brick masonry in facade / screen wall / vertical fins and patterned brickwork as per approved architectural drawings using first class facing bricks of approved make and colour in mixed natural shades (red/brown/beige/grey/white), size 230×110×75 mm, having water absorption not more than 15% and compressive strength not less than 10.5 MPa. Brickwork shall be laid in cement mortar 1:6 (1 cement : 6 coarse sand) with bricks soaked in water for minimum one hour before use, maintaining uniform 10 mm thick joints finished flush or slightly recessed with pigmented mortar to match approved shade. The work includes execution of decorative patterns, vertical fins, staggered courses, openings and projections, maintaining line, level and plumb, providing necessary brick ties/anchors wherever required, complete. Exposed faces shall not be plastered and shall be cleaned on completion using soft brush and clean water, followed by proper curing for minimum 7 days. The rate includes cost of all materials, labour, scaffolding, cutting of bricks, curing, cleaning, tools & tackles, leads and lifts and all incidentals, complete as directed by Engineer-in-Charge. RCC lintels, bands, beams, steel supports and protective brick sealer shall be measured and paid separately.

Providing and fixing mild steel support members (plates / flats / angles / rods / pipes, as approved) inside single brick thick vertical brick fins, including marking, drilling / core cutting holes of required diameter and depth in brick masonry, complete. The steel members shall be of approved section and size, conforming to IS 2062, properly cleaned of rust, oil and scale and finished with one coat of red oxide zinc chromate primer before fixing. Steel supports shall be accurately positioned true to line, level and plumb as per approved drawings and directions of Engineer-in-Charge. Fixing shall be carried out using approved chemical adhesive / epoxy anchoring compound / non-shrink grout / PU sealant of approved make, including filling of drilled holes and voids, ensuring proper bonding between steel and masonry. Excess adhesive/grout shall be neatly removed and exposed surfaces made good to match surrounding brickwork finish. he work shall include all labour, materials, drilling equipment, scaffolding, tools & tackles, cutting, priming, fixing, filling, finishing, leads and lifts, complete.

Water Repellent Treatment:

Existing surface to be cleaned using wire brush and air blower to make it free from loose particles and dust. On dry conditions apply Zydex Make Zycosil Max mixing with clean water in 1:45 (in ltr) using normal spray till saturation with a coverage of 43 to 46 SQM per 46 ltr solution. Leave the treated surface for 2/3 days for self air cure.

PANNELLING WITH 6 MM THK LECQUERED GLASS OF APPROVED SHADE- Providing and fixing of 6mm thick lacquer glass SGG Planilaque glass of approved color by architect/ Client with SGG Planifix silicon on perfectly leveled water proof non-conventional plywood (preferably marine plywood) of minimum 12mm thickness mounted on the BRICK or RCC wall/any other structure. The SGG Planilaque lacquered glass to be of 6mm thick highly durable, humid resistance, poly urethane lacquer glass. The Planilaque glass should be manufactured by industrial curtain coating process. It should meet quality standards as per BS EN 1036 1999 & confirms to PERSOZ hardness test of at least 220 oscillations. The substrate of the glass should conform to Standard BS EN 572 1995 parts 1 and 2: Glass in Building – Basic soda lime silicate glass products. Planilaque lacquered glass to be manufactured to right specifications, relating to consistency of color, opacity and homogeneity throughout production campaigns and also to the ageing properties, mechanical resistance, and resistance to humidity and to chemical agents of the lacquer. The color of the lacquer should remain stable when exposed to normal levels of ultraviolet light in interior.

Parking flooring

Car park flooring of 2mm thick: Providing & applying broadcast pigmented PU paint floor topping (Grinding + crack filling + priming + broad casting with SQ sand + final roller coatwith PU topcoat), ground to crest. Products manufactured by MYK Arment Pvt Ltd. or approved equivalent

4" Yellow Strip

Epoxy signage like Arrow / Exit etc. 200x200mm to 500x500mm size considered

Epoxy numbering (MAX. 6 Digits) Max 200x200mm size

JOINERY WORK

Architraves: Supplying and fixing Premium Teak Wood Architraves (door trims) of approximate size 75 mm (W) x 18 mm (Thick), meticulously crafted from first-quality seasoned CP (Central Province) Teak Wood or approved equivalent. The architrave shall feature a sophisticated moulded profile (e.g., chamfered, fluted, or step-profile) as per the architectural design, precision-machined to ensure uniform contours across all lengths. Installation shall be carried out over existing door frames using high-quality wood adhesive and headless finishing nails, with all joints mitre-cut at 45 degrees for a seamless corner fit. All surfaces shall be sanded to a glass-smooth finish and treated with a premium satin PU (Polyurethane) clear coating to highlight the natural wood grain and protect against moisture. The rate shall be inclusive of seasoned teak wood, specialized carpentry labor for mitring and fixing, PU polishing, , and transportation as per the instructions of the Engineer-in-Charge.

Providing and fixing Cylindrical Lock - Techno Z- Reversible Key Stainless Steel of approved make with necessary screws etc. complete as per manufacturer's specifications and direction of Engineer-in-Charge

Providing and fixing concealed type hydraulic door closer, suitable for single / double leaf hinged doors, concealed within door leaf and frame, complete with all accessories, screws, fixing arrangements and making good the surfaces, all complete as per specifications and directions of Engineer-in-Charge. The concealed door closer shall be of high-strength aluminium alloy / steel housing with corrosion-resistant finish and CE certified and conforming to EN 1154 or equivalent international standard. Suitable for doors weighing up to 60 kg (or as specified). Designed for smooth, controlled and silent operation.Door closer body shall be completely concealed to maintain architectural aesthetics. Hydraulic mechanism shall be oil-filled, leak-proof, and factory sealed. Make: Godrej or approved equivalent.

Providing and fixing universal centre lock US20 with EPC & LKP locks for glass door. Make Dorma or equivalent

Providing and fixing TGDID 300 x 22s, satin S S 304 Pull handle of Dorma or equivalent make with necessary screws etc. complete :

ALUMINIUM WORK

Supplying and installing Aluminium System – Fixed windows/Partition made out of ALUPURE / equivalent make, frame dimension 39 mm x 42 mm with corners mechanical joints. Aluminium sections extruded through NALCO billets with alloy 6063 T6 grade. With complete wind load calculation as per IS 875 (Part-3). Almost unlimited choice of colours due to finishing techniques such as anodising and powder coating. System to accommodate glass thickness of 4 / 5 / 6 / 8 / 10 / 12 / 14 / 20 & 22 mm. Profile manufacturer shall have authorised fabrication partner for window assembling and installation. Windows to be installed complete with all kinds of ironmongery including EPDM gaskets, bridging wedges and glass packers with suitable water draining system. Application of silicone sealant from inside / outside of Dow Corning / GE or equivalent, complete as per direction of Engineer-in-Charge.

Supplying and installing Aluminium System – Openable / Sliding windows made out of ALUPURE / equivalent make, frame dimension 39 mm x 62.9 mm and sash dimension 46 mm x 92 mm with corners mechanical joints. Aluminium sections extruded through NALCO billets with alloy 6063 T6 grade. With complete wind load calculation as per IS 875 (Part-3). Almost unlimited choice of colours due to finishing techniques such as anodising and powder coating. System to accommodate glass thickness of 4 / 5 / 6 / 8 / 10 / 12 / 14 / 20 & 22 mm. Profile manufacturer shall have authorised fabrication partner for window assembling and installation. Windows to be installed complete with all kinds of ironmongery including EPDM gaskets, bridging wedges and glass packers with suitable water draining system. Application of silicone sealant from inside / outside of Dow Corning / GE or equivalent, complete as per direction of Engineer-in-Charge.

Providing, fabricating and fixing aluminium alloy decorative perforated / laser-cut screen / partition, made out of aluminium alloy sheet AA-1100 / 3003 / 3105 / 5052 / 5083, of approved pattern and design, 1.50 mm to 2.00 mm thick, including aluminium alloy supporting frame of required size and section, complete with cutting, bending, welding, grinding, finishing, surface preparation, providing and fixing stainless steel fasteners, brackets, anchors and accessories, powder coated / anodized / PVDF coated finish of approved colour and shade, transportation, handling, hoisting and fixing in position at all heights, complete as per approved drawings, specifications and direction of Engineer-in-Charge.

CEILING AND WALL PANELING WORK

Providing and fixing false ceiling at all height including providing and fixing of all Providing & Fixing horizontal level suspended ceiling comprising of Aluminium Lay-in Plain 600x600mm (Nominal Size) tiles made of AA-3003-H14 (Tempered) grade Aluminium suitable for architectural finishes in 0.7mm thickness as per in IS:2676 (1981) in Global white color with Square Tegular edge having 8mm drop and 10mm flange. The difference between the 2 diagonal dimensions of the tile to be less than 1mm. Tiles shall be flattened by precision leveller to minimize sag to less than 1/400mm. The tile shall be electrostatically polyester powder coated using RoHS compliant powder having coating thickness ranging from 60-80 microns. The powder coating shall pass Salt Spray Test for 750 hours as per ASTM B117, QUV –A Test for 1000 hours as per ASTM G-154 – (Cycle – 1) and Humidity test for 1000 hours as per DIN 50017. The powder coating shall have an adhesion of GT0 as per EN ISO 2409. The shade variation across batches shall be delta E<1 using Excite/BYK Gardner instrument and gloss level of 25±5% at 60˚ as per ASTM D523.The tile shall have a Light Reflectance of ≥ 63% in accordance to ASTM 1477-98 and Fire Performance of class 0/1 as per BS 476 Part 6 & 7 in module size of 600x600mm. All border cut tiles shall be laid, using Knauf lay-in end cap for installation to have a tegular effect on perimeters

Providing and fixing false ceiling at all height including providing and fixing of all, Providing and Fixing Woodworks Linear of nominal width 100mm, having 80mm wide panel with 20mm reveal having a thickness of 15mm thickness and length 2400 mm. The panel shall be made of a Moisture resistant fibre board substrate having a minimum density of 595 Kg/m3 with a laminated facing as per the approved shade (Portland Maple, Sea Beech, Siam Wood & Mystique Walnut) and a melamine balancing layer on the reverse side. The panel shall have 0.7mm PVC edge banding along the length side with a similar finish as that of the face. The back of the panel shall have a black acoustic felt to cover the reveal of 20mm to attain an NRC of 0.5 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423. The panels shall provide a Humidity Resistance (RH) of 70% with camber limit less than 1mm/1000mm and bow less than 1mm/300mm. The back of the panels shall be profile-grooved to receive 3600mm special linear carrier (PeakForm Prelude XL Main Beam) with integrated factory fitted clips for installation.

Providing and fixing false ceiling at all height including providing and fixing of all, Providing & fixing Plywood Paneling with 12mm thick BWP IS:710 grade plywood with 1mm thick antibacterial laminate of approved make fixed on plywood/Aluminium framework of section 19mm x 50mm or as required @ 600mm c/c bothways including all hardwares all complete as per direction of the EIC. (colour & shade to be approved before procurement & use).

Providing & Fixing teak wood profile beading of section 100mm x 20mm with melamine polish on Ceiling, wall panelling, column panelling or other areas with all required hardware, fixtures and accessories including cost of all materials, labour, conveyance, T&P etc. complete in all respect as per the direction of the Engineer-in-Charge

WALL PANNELING WORKS

Providing and fixing decorative designer wall paneling of approved make, made of composite material such as HIPS with natural cork or equivalent eco-friendly surface, having minimum thickness not less than 1.0 mm, in standard panel sizes (approx. 2400 mm × 1200 mm) or as approved, on Interior walls / columns / vertical surfaces, etc. as per drawings and directions of Engineer-in-Charge. The item includes cost of all such as supply of decorative composite wall panels of approved shade, texture, and pattern, preparation of wall surface, including cleaning, leveling, and ensuring sound, dry substrate, application of approved manufacturer-recommended adhesive suitable for composite panels, Cutting, shaping, and edge finishing of panels to required sizes, Fixing panels true to line, level, and plumb, ensuring proper alignment and pattern continuity, formation of uniform joints, neat edges, and clean junctions, cut-outs for electrical fittings, switches, and service outlets wherever required, finishing of corners, edges, and joints with matching trims / sealant as approved.

Providing and fixing decorative designer wall paneling of approved make, made of composite material such as HIPS with Fabric eco-friendly surface, having minimum thickness not less than 1.2 mm, in standard panel sizes (approx.1220 mm × 2440 mm) or as approved, on Interior walls / columns / vertical surfaces, etc. as per drawings and directions of Engineer-in-Charge. The item includes cost of all such as supply of decorative composite wall panels of approved shade, texture, and pattern, preparation of wall surface, including cleaning, leveling, and ensuring sound, dry substrate, application of approved manufacturer-recommended adhesive suitable for composite panels, Cutting, shaping, and edge finishing of panels to required sizes, Fixing panels true to line, level, and plumb, ensuring proper alignment and pattern continuity, formation of uniform joints, neat edges, and clean junctions, cut-outs for electrical fittings, switches, and service outlets wherever required, finishing of corners, edges, and joints with matching trims / sealant as approved.

Providing and fixing decorative designer NENO DECOR Surfacing of approved make, supplied in roll form, made of high-quality composite decorative surfacing material, suitable for interior applications. The surfacing shall be in approved design and shade , supplied in standard roll size of 600 mm × 6 M , and shall be fixed on interior walls, columns, plywood, MDF, laminates, tiles, or other approved vertical surfaces, as per drawings and directions of the Engineer-in-Charge. The item includes the cost of supply of decorative surfacing rolls of approved pattern and color; preparation of the surface including cleaning, leveling, and ensuring a sound, dry, and smooth base; application of manufacturer-recommended adhesive suitable for decorative surfacing; cutting and trimming of sheets to required sizes; fixing the surfacing true to line, level, and plumb, ensuring proper alignment, pattern continuity, and smooth finish; formation of neat joints and clean edges; providing necessary cut-outs for electrical fittings, switches, and service outlets wherever required; and finishing of edges, corners, and joints neatly, complete in all respects. The surfacing shall be waterproof, termite-proof, fire-retardant, and durable, as per manufacturer’s specifications.

Providing and fixing Metadecor decorative wall panels of approved make, ready-to-install type, manufactured from HD-HMR-MDF with decorative liquid metallic coated and textured finish, in approved design and shade . The panels shall be of standard size(2400 × 600 mm) with a thickness of 6 mm, and shall be fixed on interior walls, columns, and other vertical surfaces, as per drawings and directions of the Engineer-in-Charge. The item includes the cost of supply of Metadecor panels of approved texture, pattern, and finish; preparation of the surface including cleaning, leveling, and ensuring a sound, dry, and even substrate; application of approved manufacturer-recommended adhesive suitable for MDF decorative panels; cutting, shaping, and edge finishing of panels to required sizes; fixing panels true to line, level, and plumb, ensuring proper alignment and pattern continuity; formation of uniform joints with neat edges and clean junctions; providing necessary cut-outs for electrical fittings, switches, and service outlets wherever required; and finishing of corners, edges, and joints with matching trims or sealant as approved, complete in all respects.

Providing and fixing decorative HD-HMR fluted wall panels of approved make, manufactured from high-density high-moisture-resistant (HD-HMR) boards, having a nominal thickness of 16.5 mm, in approved design and shade. The panels shall be of standard size( 2400 x 1200) and shall be installed on interior walls, columns, ceilings, or other vertical surfaces, strictly as per drawings and directions of the Engineer-in-Charge. The item includes the cost of supply of decorative wall panels of approved texture and finish; preparation of the surface including cleaning, leveling, and ensuring a sound, dry, and even substrate; application of approved manufacturer-recommended adhesive suitable for MDF decorative panels; cutting, shaping, and edge finishing of panels to required sizes; fixing panels true to line, level, and plumb, ensuring proper alignment and pattern continuity; formation of uniform joints with neat edges and clean junctions; providing necessary cut-outs for electrical fittings, switches, and service outlets wherever required; and finishing of corners, edges, and joints with matching trims or sealant as approved, complete in all respects.

Providing and Fixing of Optra Acoustical Wall Panel with square edges made of fibre glass substrate 25mm thick, wrapped on the front side with an acoustically transparent fabric as per the approved shade (Husk, Copper, Sangria, Sesame, Coffee, Charcoal, Titanium, Flame, Peanut and Shell). The panel shall be classified for Fire Class A, as per ASTM E-84. The Acoustical Wall Panel shall be of sizes 600x600mm (Nominal) or 600x1200mm (Nominal) and shall achieve an NRC of 0.85 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) with 50mm airgap as per ASTM C423 to be fixed to wall on a framework of wooden battens and using Wall panel Impalers (supplied by the manufacturer) or by using construction adhesives (as per the instructions laid down by the manufacturer). The fibre glass substrate shall have a recycle content of 85%.

Providing and Fixing Channelled Woodworks perforated panels of width 192mm, thickness of 15mm and length 2400 mm, made of a Moisture resistant fibre board substrate with a laminated facing as per the approved shade (Portland Maple, Sea Beech, Siam Wood & Mystique Walnut, Interior White, Alumina Pearl) and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the reverse surface has a “Helmholtz” fluted perforation with consecutive 3mm wide groove followed by 13mm of visible pane. The edges of the panel shall be “tongue-and-grooved” to fix special clips for installation and seamless visual. The back of the perforated panel shall have sound absorbing non-woven Soundtex acoustical fleece hot pressed to achieve NRC of 0.6. (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 and Humidity Resistance (RH) of 70% with camber limit less than 1mm/1000mm and bow less than 1mm/300mm.The panels shall be mounted on special aluminium splines (keel) using inside clips provided by Knauf and approved by the Architect/ Engineer-in-Charge

PANELLING ON WALLS/ COLUMNS WITH 19MM THK PLYWOOD AND FINISHED WITH LAMINATE: Providing and fixing panelling on wall with using 19mm thk commercial ply or in aluminium framing made of Heavy duty Aluminium Box Sections 50mm x 25 mm x @ 600mm c/c Both ways horizontally and vertically on the wall.This framing would be covered by 8mm thk. commercial Ply and finished with 1mm thick antibacterial laminate of approved make fixed on plywood. All complete as per Engineer in Charge.

Supplying and fixing Premium Terracotta 3D Mural Wall Cladding featuring authentic Jharkhand Tribal Art (Sohrai or Khovar motifs) as per approved design. The mural shall be composed of high-quality, high-fired natural clay tiles, approximately 20 mm to 30 mm thick, featuring intricate hand-etched or relief-moulded depictions of traditional tribal life, including village scenes, local flora, and fauna. Each tile shall be precision-crafted to ensure seamless pattern continuity across the entire installation area. The cladding shall be fixed to a prepared masonry or plywood surface using high-strength polymer-modified tile adhesive with uniform 2-3 mm spacer joints filled with matching terracotta-colored grout. All surfaces shall be treated with a matte-finish transparent water-repellent silane sealer to prevent moisture absorption and efflorescence while maintaining the natural earthen hue. The rate shall be inclusive of terracotta tiles, specialized artistry and labor, adhesive, grouting, protective sealing, , and all necessary scaffolding as per the instructions of the Engineer-in-Charge.

STRUCTURAL GLAZING & FACADE WORK

Providing and fixing Glass Reinforced Concrete (G.R.C) Screens in approved size, pattern, design, shade and thickness of 50mm on frame and design element in 30mm thick have weight approximately between 3.5 – 4 Kg per Sq. Ft. and color of M/S UniStone/Samudyam make or equivalent. The above weight and thickness is considering dimensions of screens up to 2133mm in height and 1219mm in width and having at least 50% void space. The screens should be made from ‘53 grade’ White Portland Cement manufactured by separated ISI company, Quartz, Fine Silica Sand, Alkali Resistant Glass Fiber manufactured by ‘N.E.G JAPAN’ or equivalent, Super Plasticizers manufactured by ‘BASF’ or equivalent, Polymers manufactured by ‘BASF’ or equivalent and U.V resistant Synthetic inorganic pigments should be used for pigmentation manufactured by ‘BAYFERROX (Germany)’ or equivalent. The material casting should take place in FRP Molds. The fixing of Screens should be ‘Dry fixing’ i.e. to be done with M.S Galvanized Clamps, fixtures and fasteners of Hilti / Fischer.

Providing and Fixing CONWOOD Marine Panel – Premium Exterior Grade Providing and fixing CONWOOD marine-grade panels moveable, manufactured from Portland cement, cellulose fibre and asbestos-free composite materials, being an eco-friendly (green) product suitable for marine and extreme climatic conditions. Panels shall be of size as per manufacture and natural colour finish. The panels shall have a gross density of 1260 kg/m³, with thickness swelling after 24-hour water immersion not exceeding 0.065%, Shore-A hardness of 95, specific heat capacity of 0.84 kJ/kg·K, and moisture content limited to 3.4% at 65% relative humidity and 20°C air temperature, ensuring excellent dimensional stability and long-term durability in high-humidity environments. Panels shall be sandwiched on both sides of a stainless-steel frame and securely fixed using stainless-steel screws, complete with proper alignment and fixing accessories. The surface shall be finished with a polyurethane-based coating system, followed by Art of Cultural premium exterior-grade paint, suitable for prolonged exposure to moisture, salt-laden air and ultraviolet radiation. The CONWOOD panels shall be machine-sanded smooth on both faces and shall be suitable for carving, veneering, paneling and decorative applications, providing excellent resistance to rot, termites, moisture and weathering, while maintaining structural integrity and aesthetic appeal under marine or extreme climatic conditions.Complete in all respects as per drawings, specifications and directions of the Engineer-in-Charge.

STAINLESS STEEL WORK

Stainless steel ( Grade 304) work welded in built up sections/ framed work in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works, including cutting, hoisting, fixing in position etc. as required.

UNDERDECK INSULATION

Providing and fixing of 25mm thick Cross linked closed cell polyethylene (INSUshield) laminated with aluminum foil at both side, and Air-filled chambers in Capillary form having low & stable K Value of 0.0383 W/m°K (at 46 ° C), having density 33±3 Kg/m³.The rate should include cost and conveyance of all materials, joints cutting and placing to the required size, labour charges, sundries, wastage etc. at all levels complete as per direction and satisfaction of Engineer-in-charge.

COMPOUND WALL

Providing and constructing compound wall in laterite stone masonry of approved pattern and design in cement mortar with cement mortar 1:4 (1 white cement : 4 stone dust) with an admixture of pigment matching the stone shade, in foundation, plinth and superstructure, including all materials, labour, scaffolding, curing, leads and lifts, complete as per specifications and directions of the Engineer-in-Charge.

LANDSCAPE & FOUNTAIN

Hedge Plantation Preparation of beds/ trench for hedging by excavation 60cm deepx45cm wide xRM in length in all type of soils, Refilling the excavated earth after breaking clods and mixing with sludge or organic manure in the ratio of 5:1 (five part of good earth and one part of organic manure) flooding with water filling with earth if necessary(good earth laid for separately on actual measurement basis after the reduction of 20% of its volume levelling and fine dressing for planting hedge sapling.

Indoor plants Supply and placing of indoor plants in 10" earthen pots in presantable form. Approved vertities : Areca Palm / Rubber plant / Peperomia Variegated / Peace Lily /Aceroceria / 1 Cratons / Money Plants / Aglonema or approved equivalent.

Fountain Providing and constructing of Fountain, complete as per specifications and directions of the Engineer-in-Charge. FOUNTAIN: MARBLE FOUNTAIN POOL: 14’ DIA WATER EFFECT: 08’ Height PUMP: 7.5 Hp Single phase submersible open-well pump LIGHTING: 18 nos of multi color 12-watt LED light PANEL BOARD: Cable for pump set and lights upto 10mtrs. Distance with suitable panel board.

FURNITURE WORK

5-Seater L-shape Fabric Sofa: Supplying and placing in position a 5-Seater L-shape Fabric Sectional Sofa having approximate overall dimensions of 300 cm (W) x 232 cm (D) x 79.5 cm (H). The main internal structure shall be constructed using seasoned and chemically treated solid wood (Pine/Hardwood) reinforced with high-quality BWP (Boiling Water Proof) plywood for structural integrity. The seating system shall feature high-density polyurethane (PU) foam supported by heavy-duty zigzag (S-spring) suspension for ergonomic comfort and shape retention. The unit shall be fully upholstered in premium-grade, breathable fabric with a high Martindale rub count and a distinctive pinstripe finish, including wide padded armrests and integrated back cushions. The entire assembly shall be supported on sturdy, low-profile legs with a wood-look finish or high-grade PVC buffers to ensure floor protection. All materials used must be free from manufacturing defects, with exposed surfaces finished to a high degree of smoothness, inclusive of all carriage and positioning at the designated floor as per the directions of the Engineer-in-Charge.

4-Seat Modular Corner Sofa: Supplying and placing in position a 3-Seat Modular Corner Sofa having overall dimensions of approximately Width: 74 cm (29 ¼ "), Height: 23 cm (9 "), Length: 144 cm (56 ¾ ") including back cushions, with a seat height of 40 cm and seat depth of 48 cm. The internal skeletal frame shall be a hybrid construction consisting of solid wood, plywood, fibreboard, and steel for structural longevity, featuring an elastic weave (webbing) in the bottom for enhanced seating flexibility. The seating system shall utilize high-resilience cold foam (polyurethane foam 35 kg/cu.m) and polyurethane foam (20 kg/cu.m) to ensure durable comfort and shape retention. The unit shall be fully upholstered in Viarp fabric (76% cotton, 24% recycled polyester) with a clear texture and mélange effect, offering an abrasion resistance of minimum 30,000 cycles and a lightfastness level of 5. The design must include loose, removable back cushions filled with 100% recycled polyester hollow fibres for extra support. The sofa shall be elevated on high-profile steel legs with a free height of 14 cm under the furniture to facilitate easy cleaning. All covers must be fully removable and machine washable as per standard modular furniture practices. The rate shall be inclusive of all modules, hardware, , carriage, and positioning at the designated floor, including a manufacturer warranty as per standard trade practice.

3-Seater XL Synthetic Leather Sofa: Supplying and placing in position a 3-Seater XL Synthetic Leather Sofa of overall approximate dimensions 215 cm (W) x 155 cm (D) x 85 cm (H). The internal skeletal frame shall be manufactured from seasoned and chemically treated solid Pinewood (conforming to IS: 1141 and IS: 401) to ensure structural stability and resistance against termites and moisture. The seating system shall be engineered with high-resilience polyurethane (PU) foam and supported by a heavy-duty zigzag spring suspension system for superior ergonomic comfort. The unit shall be fully upholstered in high-grade, breathable synthetic leather (Leatherette) with high Martindale rub resistance for long-term durability. The design must feature an extended Chaise Lounge section for multi-postural relaxation and integrated broad armrests. The sofa shall be elevated on sturdy, high-clearance legs to facilitate easy cleaning of the floor surface. All exposed surfaces shall be finished to a high degree of smoothness, and the rate shall be inclusive of all materials, , carriage, and positioning at the designated site as per the instructions of the Engineer-in-Charge, including a minimum 1-year manufacturer warranty.

3-Seat Modular Corner Sofa: Supplying and placing in position a 3-Seat Modular Corner Sofa having overall symmetrical dimensions of approximately Width: 74 cm (29 ¼ "), Height: 23 cm (9 "), Length: 108 cm including back cushions, with a seat height of 40 cm and seat depth of 48 cm. The internal skeletal frame shall be a hybrid construction consisting of solid wood, plywood, fibreboard, and steel for structural longevity, featuring an elastic weave (webbing) in the bottom for enhanced seating flexibility. The seating system shall utilize high-resilience cold foam (polyurethane foam 35 kg/cu.m) and polyurethane foam (20 kg/cu.m) to ensure durable comfort and shape retention. The unit shall be fully upholstered in Viarp fabric (76% cotton, 24% recycled polyester) with a clear texture and mélange effect, offering an abrasion resistance of minimum 30,000 cycles and a lightfastness level of 5. The design must include loose, removable back cushions filled with 100% recycled polyester hollow fibres for extra support. The sofa shall be elevated on high-profile steel legs with a free height of 14 cm under the furniture to facilitate easy cleaning. All covers must be fully removable and machine washable as per standard modular furniture practices. The rate shall be inclusive of all modules, hardware, , carriage, and positioning at the designated floor, including a manufacturer warranty as per standard trade practice.

3-Seater Synthetic Leather Sofa Supplying and placing in position a 3-Seater Synthetic Leather Sofa having overall approximate dimensions of 1204.5cm x 98cm x 94.5cm. The internal skeletal frame shall be constructed from seasoned and chemically treated solid Pinewood (conforming to IS: 1141) to ensure structural rigidity and resistance to warping. The seating and backrest system shall be engineered with high-resilience polyurethane (PU) foam of density not less than 28-32 kg/cu.m, reinforced with a heavy-duty zigzag spring (S-spring) suspension for long-term comfort and shape retention. The unit shall be fully upholstered in premium-grade, breathable synthetic leather (Leatherette) with high Martindale rub resistance for heavy-duty usage. The design shall feature broad, padded armrests and a high backrest for enhanced lumbar support, elevated on sturdy, high-clearance legs to allow for easy floor maintenance. All materials used must be free from manufacturing defects, with exposed surfaces finished to a high degree of smoothness. The rate shall be inclusive of all materials, carriage, , and positioning at the designated floor as per the instructions of the Engineer-in-Charge, including a minimum 1-year manufacturer warranty.

2-Seatar Sofa: Supplying and placing in position a 2-Seat Modular Sofa with a seat height of 40 cm and seat depth of 48 cm. The internal skeletal frame shall be a hybrid construction consisting of solid wood, plywood, fibreboard, and steel for structural longevity, featuring an elastic weave (webbing) in the bottom for enhanced seating flexibility. The seating system shall utilize high-resilience cold foam (polyurethane foam 35 kg/cu.m) and polyurethane foam (20 kg/cu.m) to ensure durable comfort and shape retention. The unit shall be fully upholstered in Viarp fabric (76% cotton, 24% recycled polyester) with a clear texture and mélange effect, offering an abrasion resistance of minimum 30,000 cycles and a lightfastness level of 5. The design must include loose, removable back cushions filled with 100% recycled polyester hollow fibres for extra support. The sofa shall be elevated on high-profile steel legs with a free height of 14 cm under the furniture to facilitate easy cleaning. All covers must be fully removable and machine washable as per standard modular furniture practices. The rate shall be inclusive of all modules, hardware, , carriage, and positioning at the designated floor, including a manufacturer warranty as per standard trade practice.

1-Seater L-shape Fabric Sofa: Supplying and placing in position a 5-Seater L-shape Fabric Sectional Sofa having approximate overall dimensions of 80 cm (W) x 80 cm (D) x 79.5 cm (H). The main internal structure shall be constructed using seasoned and chemically treated solid wood (Pine/Hardwood) reinforced with high-quality BWP (Boiling Water Proof) plywood for structural integrity. The seating system shall feature high-density polyurethane (PU) foam supported by heavy-duty zigzag (S-spring) suspension for ergonomic comfort and shape retention. The unit shall be fully upholstered in premium-grade, breathable fabric with a high Martindale rub count and a distinctive pinstripe finish, including wide padded armrests and integrated back cushions. The entire assembly shall be supported on sturdy, low-profile legs with a wood-look finish or high-grade PVC buffers to ensure floor protection. All materials used must be free from manufacturing defects, with exposed surfaces finished to a high degree of smoothness, inclusive of all carriage and positioning at the designated floor as per the directions of the Engineer-in-Charge.

Coffee Table: Supplying and placing in position a Solid Wood Coffee Table with Dual-Level Storage having overall approximate dimensions of 100 cm (W) x 65 cm (D) x 45 cm (H). The table shall be manufactured from premium-grade, seasoned solid wood (conforming to IS: 1141) to ensure structural stability and durability. The unit shall feature a dual-shelf design, including a spacious tabletop with 8mm thick glass and an integrated bottom shelf for organized storage. All surfaces shall be finished with a high-quality Walnut PU (Polyurethane) coating, providing superior resistance to scratches, moisture, and daily wear-and-tear while preventing peeling or fading. The construction must be of knock-down (KD) type for ease of transport and assembly, with all joints and hardware designed for high load-bearing capacity (approximate weight of unit 27 kg). The rate shall be inclusive of all materials, , carriage, assembly at site, and positioning at the designated floor as per the instructions of the Engineer-in-Charge, including a standard manufacturer warranty.

Oval shaped Coffee Table: Supplying and placing in position an Oval Coffee Table having overall approximate dimensions of 180 cm (L) x 59 cm (W) x 40 cm (H). The tabletop shall be constructed of high-quality fibreboard with walnut veneer surfacing, treated with clear acrylic lacquer for durability and a smooth natural grain finish. The supporting structure shall consist of a robust steel underframe/panel finished with epoxy/polyester powder coating for structural integrity. The legs shall be made of solid walnut with a clear acrylic lacquer finish, featuring an integrated secondary storage shelf made of unbleached paper/lacquer for holding magazines and accessories. The design must feature soft, aerodynamic lines with a maximum load capacity of 20 kg on the tabletop. The rate shall be inclusive of all materials, , carriage, assembly at site, and positioning at the designated floor as per the instructions of the Engineer-in-Charge, including a standard manufacturer warranty.

Round Coffee Table: Supplying and placing in position a Round Coffee Table having a diameter of 80 cm and a total height of 42 cm. The table shall be constructed with a high-quality birch plywood tabletop and shelf, surfaced with oak veneer and finished with tinted clear acrylic lacquer to highlight the visible wood pattern. The supporting structure shall feature slightly flared legs and cross rails manufactured from solid birch, finished with tinted clear acrylic lacquer for structural stability and a warm, natural aesthetic. The unit must include a lower storage shelf with a load capacity of 10 kg, while the tabletop must support a maximum load of 20 kg. All components shall be designed for knock-down (KD) assembly with high-quality metal fasteners. The rate shall be inclusive of all materials, , carriage, assembly at site, and positioning at the designated floor as per the instructions of the Engineer-in-Charge, including a standard manufacturer warranty.

Modular Corner Table: Supplying and placing in position a Modular Corner Table having overall approximate dimensions of 59.7 cm (W) x 59.7 cm (D) x 60.5 cm (H). The table shall be manufactured from high-quality birch plywood with a premium walnut/brown wood-grain finish, designed in a unique "capsule" or rounded square shape to maximize corner utility. The unit must feature a dual-level storage configuration, comprising a top surface and an integrated bottom shelf for enhanced functionality. The construction shall be of the knock-down (KD) type, providing a compact footprint with high load-bearing capacity for everyday use. All edges shall be smoothly finished, and the surfaces must be treated for easy maintenance and scratch resistance. The entire assembly (approximate weight 12 kg) shall be supported on sturdy, integrated base supports. The rate shall be inclusive of all materials, , carriage, assembly at site, and positioning at the designated floor as per the instructions of the Engineer-in-Charge, including a standard manufacturer warranty.

RECCEPTION TABLE Supplying and installing a Premium Curved Reception Counter (approx. 10' x 2.5' x 3.5') constructed from 18 mm BWP Plywood with a high-end Oak wood fluted front fascia and a seamless Quartz/Solid Surface top as per the design. The unit shall feature a precision-crafted Jharkhand Government Logo with warm-white LED backlighting, elevated on PVD-coated metallic legs in a gold finish. The internal workspace must include a lockable three-drawer pedestal, a dedicated key-management box, and a pre-wired modular electrical strip with four sockets for computer peripherals. All external timber shall be finished in satin PU coating, inclusive of cable grommets, keyboard tray, and all specialized labor and hardware required for onsite assembly as per the Engineer-in-Charge.

Executive Table in veneer finish. SIZE:- main- 2700(L)*1200(W)*750(H)mm, side return unit- 1200(L)*500(W)*750(H)mm SPECIFICATION: Providing and supplying a table with an overall size of 2700mm (length) x 1200mm (width) x 750mm (height), designed to meet your office needs. The table top is constructed using 36mm thick MDF (Medium Density Fiberboard) with a veneer finish, and it boasts a beveled edge with a silver powder-coated finish on top. This combination not only adds a touch of sophistication but also ensures the durability of the surface. The modesty panel is of the ganging type, made of 25mm thick MDF, with a veneer finish that's polished in melamine. It complements the table's aesthetic while providing structural support. Additionally, a side unit is included, measuring 1200mm (length) x 500mm (width) x 750mm (height). Its top is constructed using 25mm thick MDF board, and the understructure uses 18mm thick MDF board, ensuring both durability and a polished look. The storage area beneath the top is divided into two parts - one featuring a fixed drawer unit with a drawer+drawer+file drawer configuration, and the other featuring shutter storage with one shelf -inside. This setup enhances organization and functionality in your workspace.

Furthermore, a fixed pedestal is included, made of 18mm thick MDF board, providing additional storage space with a drawer+drawer+file drawer arrangement. To enhance the overall aesthetics and support the main table top, round CRCA (cold-rolled close annealed) pipes have been utilized as the table top support.complete hardware's as per approved design and direction of Engineer-in-Charge

EXECUTIVE OFFICE DESK Providing and supplying Executive Office Desk with overall main desk dimensions 1800mm (L) × 900mm (W) × 750mm (H), complete with integrated Pedestal Unit, and Side Return Unit dimensions 900mm (L) × 500mm (W) × 650mm (H). Desk Top Worksurface: Constructed from 25mm Thick Boiling Water Resistant (BWR) Marine Plywood (IS:710), finished with 1.5mm High-Pressure Premium Laminate (or Natural Wood Veneer with PU protective finish) on top and 1.0mm balancing laminate on the underside. Gable Ends & Modesty Panel: Constructed from 18mm Thick BWR Marine Plywood (IS:710) with 1.0mm Premium Laminate on both sides (Both Sides Laminated - BSL) for structural stability and premium finish. Pedestal & Side Unit: Pedestal unit and side storage unit constructed from 18mm Thick BWR Marine Plywood (IS:710). Pedestal comprises 2 drawers and 1 filing unit, fitted with heavy-duty soft-closing full-extension telescopic runner channels (Hafele/Hettich) and a multi-drawer zinc-alloy central locking mechanism. Edge Protection: All exposed machine-cut edges lined with 2.0mm thick high-impact ABS edge banding applied using PUR (Polyurethane) Waterproof Hot Melt Glue in approved shade. Hardware & Cable Management: Complete with SS 304 grade architectural handles, leveling glides, and aluminum flip-top brush-grommets for wire management as per approved shop drawings and direction of Engineer-in-Charge.

Computer work station: Supply and placement of computer work station of size 1200x600x750 with 18 mm thick commerical ply laminated with 1 mm thick lamination for top and sides inlucding provision of keyboard tray on telescopical channel, one CPU unit and three no of drawers with necessary hardware, eges to have teak wood liping etc complete.complete hardware's as per approved design and direction of Engineer-in-Charge

Writing table: Supply and placement of writing table of size 750 x 600 x 750 mm made out of 50 x 50 mm teakwood legs,and 70x30mm side rails top to have 18mm thick plywood with 1mm thick laminate having with 1 drawer with telescopic sliding channel, all edges to have teak wood beading etc,complete with spirit polish as per drawing.

Conference Table ‘U’ Shape: Supply and placement of Conference Table (Approx. Size – 7930x600x750) ‘U’ Shape: Number of single seater-24, Table Top plain side Edge banded with PVC tape of 2 mm thick with help of hot melt glue, Material of work top ± 36 mm laminated commercial Board, Breadth - 600 mm, Height of Work Top # 19 mm -750 mm, Length according to seating Wire Management: Hydraulic module conference table and data box pop up box cable cubby with wiring of HDMI, VGA, Audio, LAN and Power Ports (Black). Colour of Laminate: as per Eingineer-in-Charge Material & Design:as per Eingineer-in-Charge & approval. Warranty period in number of Years: 3 years Test reports to be furnished to Buyer on demand: Yes

Conference Table Providing and fixing of Conference Table for 15 persons ,600 mm wide and 750 mm height made out of 18 mm thick plywood for frame work, shelf, foot rest and front facia, provision to accommodate conduits for wiring, front, top and side end surfaces to have 3.5 mm thick approved shade veneer paneling, exposed edges of ply wood covered with teak wood beading, exposed veneer of top shall be finished with melamine polish finish of approved shade, ends and fronts veneered surfaces finished with melamine polish, internal exposed surfaces of the table finished with two coats of enamel paint over one coat of wood primer including surface preparation.Wire Management: Hydraulic module conference table and data box pop up box cable cubby with wiring of HDMI,VGA, Audio, LAN and Power Ports (Black). Colour of Laminate,Material & Design: As Per choice & approval,complete hardware's as per approved design and direction of Engineer-in-Charge

4-Seater Rectangular Dining Table: Supplying and placing in position a 4-Seater Rectangular Dining Table manufactured from premium Sheesham Wood (Indian Rosewood). The table shall have approximate dimensions of 118 cm (L) x 80 cm (W) x 74 cm (H). The tabletop and supporting structure shall be constructed of solid Sheesham wood, seasoned and treated for durability, featuring a natural wood grain finish with protective clear coating. The design shall incorporate a clean, contemporary aesthetic with sturdy square-section legs and a reinforced underframe for structural stability. All wooden surfaces shall be smooth-finished with rounded edges to prevent injury. The assembly shall be of the knock-down (KD) variety, ensuring precision joining and ease of maintenance. The rate shall be inclusive of all materials, , carriage, assembly at site, and positioning at the designated floor as per the instructions of the Engineer-in-Charge, including a standard manufacturer warranty.

Premium 4-Seater Circular Dining Table: Supplying and placing in position a Premium 4-Seater Circular Dining Table featuring a natural marble tabletop with an integrated, detachable Lazy Susan for functional serving. The table shall have a circular diameter of approximately 136 cm and a height of 78.5 cm. The tabletop shall be supported by a high-strength substructure and four tapered legs crafted from solid Ash wood, finished in a rich walnut tone with a clear protective lacquer. The marble top must be seasoned and polished to a high sheen, providing a heat-resistant and durable dining surface. The overall construction must ensure a total unit weight of approximately 129 kg for superior stability. The assembly shall be of the knock-down (KD) variety for precision fitment at the site. The rate shall be inclusive of all materials, , carriage, assembly at site, and positioning at the designated floor as per the instructions of the Engineer-in-Charge, including a standard manufacturer warranty.

Pantry table: Supply and placement of pantry table of size 1800 x 750 x 750 mm made out of 70 x 70 mm teakwood legs,and 90x30mm side rails top to have 18mm thick plywood with 1mm thick laminate all edges to have teak wood beading etc,complete with spirit polish as per drawing.

Executive High Back Chair SPECIFICATION: Providing and supplying high-back chair is Overall Size 690W x 680D x 1220H . Seat Plywood Made Of 15mm Hot Pressed Supported. Upholstery PVC Structure Moulded With Prime Quality Leatherite. PHA ( Gas-Lift ) 85mm ( TDC 152mm & BDC 67). Understructure Base Revolving chrome base. Machanism 4way locking at any pointOperated In Seating Position . Seat & Back Are Firmly Connected To The Base Frame Mechanism . Machanism Provided Upright Position Locking. Provides Maximum Adjustability And Scope For Comfort. Seat & Back moves in same direction. 1 position locking with anti shock feature. Chair max height 1220mm x 550W x 490D Base Seat 120mm Thick Moulded With P.U. Foam, D - 32 kg/m3, H - 20 & 520W x 820H Back Seat 120mm Thick Moulded With PU Foam, D - 32 kg/m3 , H - 20, 550 Handle In / 690 Handle Out Arm Rest Fitted To The Seat With Armrest Connecting Brackets. Arm Rest Letheirte on SS Plated Arm Rest Height From Seat 160mm. Height From Seat To Ground 530mm. Seating Height Can Be Adjusted With a Pneumatic Gas Lift. Pedestal Pitch Centre Dia 690mm With Casters & Without Casters 665mm. Casters Made Of Moulded Black Nylon Metal Bolt Inserted & Fitted With 5 Nos. Twin Wheel

MID BACK CHAIR SPECIFICATION: Providing and supplying Medium Back Revolving Chair with a comprehensive set of features designed for comfort and functionality. This chair comes with sturdy PP armrests, providing a comfortable place to rest your arms. The gas lift mechanism enables easy seat height adjustments, ensuring the chair can be customized to your workstation or desk. Its robust nylon base ensures stability and durability, guaranteeing long- term use. The standout feature of this chair is the mesh back and seat fabric upholstery, which offers excellent breathability and promotes air circulation, keeping you cool and comfortable during extended periods of sitting. The chair is adorned with crepe fabric tapestry, adding a touch of sophistication to the design while maintaining ease of maintenance.

CHAIR VISITOR SPECIFICATION: Providing and supplying Visitor Chair with PP (Polypropylene) Armrests, a Pipe Frame, a durable Nylon Base, a Mesh Back, and a Crepe Tapestry upholstery. This chairis designed to provide both comfort and practicality in various settings. The PP armrests offer a comfortable place for visitors to rest their arms. The pipe frame ensures stability and durability, while the nylon base enhances the chair's overall strength. The mesh back providesbreathability and comfort, allowing for better air circulation, making it a suitable choice forextended periods of sitting. The crepe tapestry upholstery adds a touch of elegance to the chair's design, making it a visually appealing and welcoming addition to any office or workspace.

Boss Chair: Providing and supplying high back revolving chair with tilting mechanism, PP (polypropylene) arm frame, pneumatic gas lift for height adjustment, and metal-inserted PP base with castor wheels for stability. The seat, back, and cushioned armrests shall be upholstered in good quality leatherette tapestry..

Revolving Chair: Providing and supplying Mid back revolving chair with tilting mechanism, PP (polypropylene) arm frame, pneumatic gas lift for height adjustment, and metal-inserted PP base with castor wheels for stability. The seat, back, and cushioned armrests shall be upholstered in good quality leatherette tapestry.

Dining chair: Supply and placement of Dining chair of size 450 x 450 x 850 mm made out of 45 X 45mm teak wood for frame & legs, 25 x 15 mm teak wood strips for the back rest and 12 mm thick commericial ply with 50 mm thick rubber foam in seat, duly upholstered with fabric of approved shade & qualilty Including spirit polish etc.all complete and as directed by Engineer -in-charge.

Writing chair: Supply and placement of Writing chair of size 450 X 400 X 835 mm made out 45 X 45mm teak wood for frame & legs, 25 x 15 mm teak wood strips for the back rest and 12 mm thick commericial ply with 50 mm thick rubber foam in seat, duly upholstered with fabric of approved shade & qualilty Including spirit polish etc., all complete and as directed by Engineer -in-charg

Easy Chair 1-Seater: Supplying and providing a Premium Easy Chair of approximate overall size 71 cm (W) x 81 cm (D) x 76 cm (H) (28" x 32" x 30"), meticulously crafted from first-quality seasoned Teak Wood as per the reference design. The chair shall feature an ergonomically reclined solid teak frame with tapered legs and elegantly curved armrests, all treated with a clear satin PU (Polyurethane) finish to highlight the natural wood grain. The seating and backrest shall be constructed with high-density 40-density U-foam for superior comfort, upholstered in a premium linen-blend breathable fabric (Beige/Cream) with a minimum 25,000 Martindale rub count for high durability. The unit includes a matching lumbar support cushion and must be reinforced with hidden tenon joints and heavy-duty hardware to ensure long-term structural stability. The rate shall be inclusive of all material costs, upholstery labor, , transportation, and onsite placement as per the instructions of the Engineer-in-Charge.

Easy Chair 3-Seater: Supplying and providing a Premium 3-Seater Easy Chair/Sofa of approximate overall size 198 cm (L) x 81 cm (W) x 76 cm (H) (78" x 32" x 30"), meticulously crafted with a reinforced frame of first-quality seasoned Teak Wood as per the reference aesthetic. The structure shall feature an elongated, ergonomically reclined solid teak frame with tapered support legs and signature curved armrests, all treated with a clear satin PU (Polyurethane) finish to preserve the natural wood grain. The seating and backrest area shall be equipped with high-resiliency 40-density U-foam and upholstered in a premium linen-blend breathable fabric (Beige/Cream) with a minimum 25,000 Martindale rub count for heavy-duty use. The unit must include three matching lumbar support cushions and feature hidden tenon joints and heavy-duty internal bracing to ensure structural integrity across the 3-seater span. The rate shall be inclusive of all material costs, upholstery labor, , transportation, and onsite placement as per the instructions of the Engineer-in-Charge.

Dressing stool: Supply and placement of wooden stool of size 305 x 305x 760mm made out of teakwood framework of size 45 x 30mm with 18mm thick plywood with cushion on top, edges to have teakwood beeding all complete with spirit polish

King Size bed: Providing and supplying of King Size Bed with Overall Size: Width — 76 inches, Length — 80 inches. Bed Structure consists of heavy-duty metal frames made of M.S. Channels in 1.6mm Thickness with anti-rust treatment. Horizontal plinths and bottom plinth are made of 25 mm Thick Boiling Water Resistant (BWR) Marine Plywood (IS:710) with 1.5mm High-Pressure Premium Laminate (Century/Greenlem/Merino or equivalent). Plinth support assembly is made of M.S. 25 mm square pipe in 2.0 mm thickness. Head Board is made of 18 mm thick BWR Marine Plywood (IS:710), front face fitted with an ergonomically padded cushion backrest consisting of 50mm thick High-Resilience (HR) Polyurethane Foam (40 Density) upholstered in premium stain-resistant fabric/leatherette, with 2.0mm high-impact ABS edge banding glued with PUR (Polyurethane) Waterproof Hot Melt glue on exposed edges. Tail Board is made of 18 mm thick BWR Marine Plywood (IS:710) with 2.0mm high-impact ABS edge banding glued with PUR Waterproof Hot Melt glue. Side Rails are made of 18 mm thick BWR Marine Plywood (IS:710) with 2.0mm high-impact ABS edge banding glued with PUR Waterproof Hot Melt glue. Mattress Panels made of 18 mm BWR Marine Plywood (IS:710) in Imperial Oak shade. Lipping shade is 299P (ABS Grade). Complete hardware using concealed Hafele / Hettich heavy-duty connectors and SS 304 fittings as per approved design and direction of Engineer-in-Charge.

Single bed Supply and placement of hard bed single wooden of size 2000 x 950 x 400mm made out of teak wood with side rail of size 120x30 mm. head board of size 950(width)X750(Ht) and foot board 950(width) x 400(Ht) made out of 70x30mm hard wood frame covered with 4mm thick one side teak ply and other side 4mm thick commercial ply edges to have 40x6mm thick teak wood lipping and ,4 nos of 50 x 30 mm support of second class hard wood and 12mm thick commercial ply on bed top all finished melamine polish etc all complete as per drawing

BEDSIDE TABLE Supply and placement of Bed side table size 450 x 450 x510 mm made out of 18 mm thick BWR Marine Plywood. Sides, front & top to have 1.5mm High-Pressure Premium Laminate (Century/Greenlem/Merino or equivalent) and all other exposed and inside surfaces finished with approved white colour premium laminate (Century/Greenlem/Merino), 6 mm thick BWR Marine Plywood on the back side, one drawer wtih handle made out of side 12 mm thick BWR Marine Plywood and bottom of 4 mm BWR Marine Plywood ride on telescopic channels provided with one open shelf. All the exposed edges are edge banded with 0.8 mm thick PVC edge banding. The high quality hardware used like Roller slides, Hinges , minifix, dowels is of make Hettich.Construction : Knock Down construction approved design and direction of Engineer-in-Charge

Bench cushioned: Supplying and placing in position a Upholstered Bedroom Bench with a total width of 120 cm (47.25 in), depth of 45 cm (17.75 in), and height of 50 cm (19.75 in). The bench frame and legs shall be constructed from solid Acacia wood, finished in a polished "Rich Mahogany" stain for a modern, high-gloss aesthetic. The unit shall feature a backless and armless design, topped with a detachable high-density foam cushion upholstered in a durable Ivory polyester-blend fabric. The cushion shall be secured to the wooden frame using integrated fabric ties. The bench must be designed for a minimum weight capacity of 113 kg (250 lb) and feature smooth-finished wooden components. All complete as per approved design and direction of Engineer-in-Charge including manufacturer warranty.

Premium King Size Latex Foam Mattress: Supplying and placing in position a Premium King Size Latex Foam Mattress with nominal dimensions of 198 cm (78 in) x 203 cm (80 in) and a thickness of 25.4 cm (10 in). The mattress core shall be composed of high-resilience Latex Foam layers designed for orthopaedic back support and pressure relief. The external upholstery shall be a high-quality, breathable knitted fabric that is soft to the touch and durable. The construction shall be eco-friendly using sustainable materials, pre-assembled at the factory to ensure consistent bonding and density. The unit must be designed to resist sagging and maintain structural integrity over prolonged use. The rate shall be inclusive of all materials, , carriage, and positioning on the bed frame at the designated floor as per the instructions of the Engineer-in-Charge, including a 5-year manufacturer warranty.

Premium High-Comfort King Size Mattress: Supplying and placing in position a Premium High-Comfort King Size Mattress with nominal dimensions of 198 cm (78 in) x 203 cm (80 in) and a total thickness of 25.4 cm (10 in). The mattress core shall be engineered with a triple-layer foam system, specifically incorporating high-density Softy Foam and Pressure-Relieving PU Foam to provide cloud-like cushioning and ergonomic support for the back, hips, and shoulders. The unit shall be upholstered in a premium Sparkle White Knit Fabric featuring a quilted finish for enhanced aesthetics and breathability. The base of the mattress must be equipped with an anti-skid fabric layer to prevent displacement on the bed frame. The product shall be factory pre-assembled with an approximate unit weight of 21.00 kgs. The rate shall be inclusive of all materials, , carriage, and positioning at the designated location as per the instructions of the Engineer-in-Charge, including a 5-year manufacturer warranty against manufacturing defects.

Single Bed Foam Mattress: Supplying and placing in position a Standard Comfort Single Bed Foam Mattress with nominal dimensions of 1Width - 38 inches Length — 80 inches and a thickness of 5 inches. The mattress shall be constructed with a high-quality PU Foam core designed to offer a balanced blend of support and softness for daily residential or hostel use. The external upholstery shall feature a durable and breathable Knitted Fabric finish to enhance surface comfort and hygiene. The unit is designed for lightweight handling with an approximate weight of 6.23 kgs, making it suitable for easy maintenance and flipping. The rate shall be inclusive of all materials, , carriage, and positioning on the single bed frame at the designated floor as per the instructions of the Engineer-in-Charge, including a 1-year manufacturer warranty.

Pillows: Supply and placement of pillows of approved make recon or equivalent

Cushions with cover Supplying and placing in position Premium Grade Cushions (Square or Rectangular) consisting of a high-density insert and a removable decorative cover. The Insert shall be encased in a 100% cotton down-proof cambric shell, generously filled with virgin micro-fibre (grade 1.5D or 3D) or high-resilience conjugated polyester fiber to ensure "bounce-back" elasticity and prevent sagging. The Cushion Cover shall be fabricated from premium upholstery fabric (such as Velvet, Jacquard, or heavy-duty Linen-blend) with a minimum weight of 400-500 GSM and a lightfastness rating of 5+. The cover shall feature a concealed YKK nylon zipper at the bottom edge and a "piped" or "flanged" border for enhanced structural aesthetics. Internal seams must be double-stitched and overlocked with high-tenacity thread to prevent fraying under pressure. The rate shall be inclusive of the insert, fabric, tailoring, , and delivery to the site as per the approved color palette and texture sample.

King Size Bed Linen Set: Supplying and providing a Premium King Size Bed Linen Set of approved design, colour & pattern consisting of one flat bedsheet and two pillow covers. The bedsheet shall be manufactured from 100% Long-Staple Compact Cotton with a minimum 400 Thread Count (TC) and a Sateen weave for a smooth, high-sheen finish. The nominal dimensions for the bedsheet shall be 274 cm x 274 cm (108 in x 108 in) to ensure adequate tuck-in for king-size mattresses. Pillow covers shall be of size 46 cm x 69 cm (18 in x 27 in) with a side flap or concealed zippered closure. The fabric must be mercerized for strength and OEKO-TEX Standard 100 certified to ensure it is free from harmful chemicals. The rate shall be inclusive of all delivery, and neat spreading over the bed at the designated location as per the instructions of the Engineer-in-Charge.

Single Bed Linen Set: Supplying and providing a Standard Quality Single Bed Linen Set (White) consisting of one flat bedsheet and one pillow cover. The bedsheet shall be manufactured from 100% Pure Cotton with a minimum 180 Thread Count (TC) and a Percale weave to ensure a crisp feel and high breathability. The nominal dimensions for the bedsheet shall be 152 cm x 228 cm (60 in x 90 in) to provide sufficient overhang for a standard single mattress. The pillow cover shall be of size 46 cm x 69 cm (18 in x 27 in). The fabric must be color-fast and pre-shrunk to ensure dimensional stability after multiple industrial washes. The rate shall be inclusive of all carriage, and neat spreading over the bed at the designated location as per the instructions of the Engineer-in-Charge.

Premium All-Season Comforter with cover: Supplying and providing a Super-Premium All-Season Down-Alternative Comforter for King Size bed with nominal dimensions of 274 cm x 274 cm (108 in x 108 in). The filling shall consist of 350-400 GSM Ultra-Fine Micro-Down Fiber (siliconized) designed to mimic the loft and warmth of natural goose down while remaining hypoallergenic. The outer shell shall be manufactured from 100% Egyptian Cotton with a minimum 300 Thread Count (TC) and a Down-Proof finish to prevent fiber migration. The quilt must feature a Box-Stitch (Baffle Box) construction to ensure even distribution of filling and prevent cold spots. The edges shall be finished with double-needle stitching and premium gold/silver piping. The product must be antimicrobial, breathable, and OEKO-TEX certified. The rate shall be inclusive of all materials, , carriage, and neat placement as per the instructions of the Engineer-in-Charge.

All-Season Reversible Comforter with cover: Supplying and providing a High-Resilience All-Season Reversible Comforter (King Size) with nominal dimensions of 254 cm x 274 cm (100 in x 108 in). The filling shall be comprised of 300 GSM hollow-conjugate siliconized microfiber, engineered for high loft-retention and breathability. The outer casing shall be made of 100% Cotton with a minimum 250 Thread Count (TC), featuring a soft-brushed finish for comfort. The quilt shall be constructed using precision diamond-pattern quilting or cloud-stitch patterns to prevent the filling from shifting or bunching. The product must be hypoallergenic, dust-mite resistant, and finished with reinforced piped edges for structural integrity. The rate shall be inclusive of all materials, , carriage, and placement at the designated location as per the instructions of the Engineer-in-Charge.

Single Bed Comforter/Quilt with cover: Supplying and providing a Standard Quality Single Bed Comforter/Quilt suitable for dormitory or hostel use, with nominal dimensions of 152 cm x 228 cm (60 in x 90 in). The filling shall consist of 200-250 GSM Thermally Bonded Polyester Wadding, ensuring the insulation layer remains intact and does not lumpy after multiple washes. The outer shell shall be manufactured from High-GSM Micro-peach/Microfiber fabric (minimum 100 GSM fabric weight) with a soft-touch finish. The quilt shall feature Box-pattern or Wave-pattern machine quilting across the entire surface to secure the internal filling. All edges shall be securely locked with specialized interlock stitching or bias-binding finish to prevent fraying under heavy usage. The product shall be lightweight, hypoallergenic, and machine-washable. The rate shall be inclusive of all materials, , carriage, and delivery at the designated floor/location as per the instructions of the Engineer-in-Charge.

Bed Runner: Supplying and providing a Premium Bed Runner . The runner shall have approximate dimensions of 240 cm x 60 cm (94" x 24"), suitable for King size beds, featuring a multi-layered construction with a top face of high-thread-count premium polyester-viscose blend or faux-silk fabric. The color and design shall be as per approved. The fabric shall be finished in a sophisticated, featuring a minimum GSM of 300 for a heavy, luxurious drape. The rate shall be inclusive of fabric cost, high-density infills, specialized tailoring labor, and delivery to the site as per the instructions of the Engineer-in-Charge.

Throw: Supplying and providing a Premium Knitted Cotton Decorative Throw with nominal dimensions of 127 cm x 178 cm (50 in x 70 in). The throw shall be crafted from 100% premium-grade breathable cotton, featuring an intricate knit pattern designed to provide soft texture, warmth, and aesthetic layering for sofas, chairs, or beds. The unit shall be finished in a Mimosa (Yellow/Mustard tone) color with high color-fastness properties. The edges shall be neatly finished to ensure durability and prevent unraveling of the knit. The product must be skin-friendly and suitable for hand-washing in cold water. The rate shall be inclusive of all materials, , carriage, and placement at the designated location as per the instructions of the Engineer-in-Charge, including a 1-year manufacturer warranty.

Door foot mats: Supply and placement of door foot mats of duro turf make

Synthetic bath mat: Supply and placement of synthetic bath mat of size 600 x 450 mm of approved make

Premium Hand-Tufted Rug (8' x 10'): Supplying and providing a Premium Hand-Tufted Rug with nominal dimensions of 244 cm x 305 cm (8' x 10'). The rug shall be manufactured using high-quality 100% Microfiber yarns, featuring a sophisticated dual-texture construction with integrated loop and cut pile patterns to provide enhanced tactile depth and comfort underfoot. The colour and patterns as per approved. The unit shall be finished with a high-density tufted face for durability in high-traffic residential or executive areas. The backing must be professionally finished to ensure structural stability and prevent edge curling. The rate shall be inclusive of all material costs, , carriage, and placement at the designated location, including a 1-year manufacturer warranty against manufacturing defects as per the instructions of the Engineer-in-Charge.

Premium Hand-Tufted Rug (9' x 12'): Supplying and providing a Premium Hand-Tufted Rug with nominal dimensions of 274 cm x 366 cm (9' x 12'). The rug shall be manufactured using high-quality 100% Microfiber yarns, featuring a sophisticated dual-texture construction with integrated loop and cut pile patterns to provide enhanced tactile depth and comfort underfoot. The colour and patterns as per approved. The unit shall be finished with a high-density tufted face for durability in high-traffic residential or executive areas. The backing must be professionally finished to ensure structural stability and prevent edge curling. The rate shall be inclusive of all material costs, , carriage, and placement at the designated location, including a 1-year manufacturer warranty against manufacturing defects as per the instructions of the Engineer-in-Charge.

Wool Rug (8' x 10'): Supplying and providing a Premium Hand-Tufted Rug with nominal dimensions of 244 cm x 305 cm (8' x 10'). The rug shall be manufactured from first-quality 100% natural wool, featuring a durable loop pile construction designed for superior resilience and a distinct textured aesthetic. The unit shall be approved colour and pattern, delivered in a pre-assembled condition, and suitable for high-end residential or office interiors. The specification includes adherence to strict care guidelines, including regular suction-only vacuuming and immediate spot cleaning to maintain fiber integrity. The rate shall be inclusive of all material costs, , carriage, and placement at the designated site as per the instructions of the Engineer-in-Charge.

Media unit: Built in Media unit made up of carcass (back panel, side panel, top & bottom), shutter and shelves with 18 mm thick BSL type (both side pre laminated) high moisture resistant MDF board (HDWR/HDMR) with stainless steel (SS-304, 18/8) hardware's as per architectural design, drawing and specification. Laminate/PU paint shall be provided all around the visible edges of the cabinets. Glazed panelled shutter shall be as per approved design and direction of Engineer-in-Charge

Side unit: Supply and placement of Side unit of 1200 x 450 x 750mm made out of 19mm thick commercial ply, top & side to have 1 mm thick laminate having one horizontal & one vertical divider of 19mm thick commercial ply, back with 6mm thick commercial ply, front to have Door with 19 mm thick commercial ply with 1 mm thick laminatefinished with melamnine polish etc as directed by Engineer -in-charge .

BACK UNIT: BACK STORAGE: 1800*500*750MM SPECIFICATION: Providing and supplying a back drop unit with an overall size of 1800mm in length, 500mm in depth, and 750mm in height. The entire body of the unit is constructed using 18mm thick MDF (medium density fiberboard), finished in veneer and duly polished withmelamine for a sleek and polished appearance. The back drop unit features storage space beneath the top, which is divided into three compartments. Tne first and last compartments are equipped with 10mm thick glass shutters with metal profiles, and each has an adjustable shelf inside. These compartments are ideal for displaying and storing items that you want to showcase. The middle compartment is divided into four equal-sized open boxes, providing versatile storage for a range of items. This design allows for efficient organization and easy access to stored belongings.complete hardware's as per approved design and direction of Engineer-in-Charge

Book Case: Supply and placement of 4 Door Book Case shall have the configuration of 914mm(W)x320mm(D)x1742mm(H). The unique design provides the right rigidity to the Top hinged doors , which shall facilitate easy use. The Book Case shall be made from prime quality CRCA steel with anti rusting treatment. It shall have a Rigid Knock Down Construction. The Top Pannel, Back Pannel and Side Pannel are made from 0.7mm high yield CRCA and other components from 0.8mm CRCA. Each door shall have a 6 Lever Cam Lock with Common Key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. Scissor Mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. complete hardware's as per approved design and direction of Engineer-in-Charge

Modular wooden wardrobe: Supply and installation of modular wooden wardrobe made of carcass (back panel, side panel, top & bottom), shutter and shelves with 18 mm thick BSL type (both side pre laminated) high moisture resistant MDF board (HDWR/HDMR) with stainless steel (SS-304, 18/8) 4 legs (100 mm high). The interior shall include a hanger rod, drawer, and shelves. Shutters shall have 250 mm SS handles and auto hinges. Includes dresser 850 × 520 × 2025 mm with three drawers and side units 400 × 520 × 2025 mm with door handles, complete hardware's as approved design and direction of Engineer-in-Charge

FULL HT. STORAGE/ CUPBOARD- Providing and fixing storage units of full height as per drwng. They shall consist of 18mm thk.BWP. ply top, sides,back, bottom, shelves and shutters. The bottom of the storages shall be at 3” from FFL. The top of storages shall touch the false ceiling level or 7'-0" ht. The shutter with box type higes of approved make & steam beach lipping finished with approved laminate on all the shutter edges. Division of the shutters shall be made equally according to the length of the storages ( as approved by Engineer-in-Charge/ architect). All the external surfaces shall be finished with 1.0mm thk. Laminate (suede finish) of approved make. 18mm thk. BWP. Ply shelves removable type supported on side steam beach wood battens on both sides at 16” interval (approximately / divided equally) shall be provided. All inner surfaces shall be finished with laminate including the shutters. Rate shall be inclusive of all necessary approved fittings like hinges, locks, 150mm long SS brushed finish handles,tower bolts, locks and any necessary hardware items. The top ply edge should be fitted with 19mm x 7mm size steam beach moulding finished with melamine.

Drapery / curtains: Providing and fixing curtain arrangement consisting of heavy fabric side curtains with inner sheer curtain complete in all respects including stitching, pleating, hooks, curtain rod/track, tie backs, and all accessories as required, as per approved design and direction of Engineer-in-Charge

Blind: Providing and fixing of manually operated blinds of Classic Wood 50mm Range with web Easy rise operation' including of all materials, labour, conveyance,sundries, tools and plants etc as per the direction of Engineer-in-charge. (colour & shade to be approved before procurment & use)( Make- Hunter Douglas/Marvel)

Wall Art canvas paintings (24 in x 48 in): Supplying and providing a Premium Wall Art canvas paintings,with a nominal size of 61 cm x 91 cm (24 in x 48 in), featuring intricate hand-painted tribal motifs, design, art, color palette and texture as per approved . Each artwork shall be stretched on a high-quality 380 GSM poly-cotton canvas and enclosed in a sleek 25 mm thick black charcoal-finish synthetic or wooden frame with a 2 mm clear float glass or high-transparency acrylic facing to protect the art from dust and UV rays. The assembly must include a sturdy MDF backboard (8 mm thick) with heavy-duty hanging hardware (D-rings and wire) to ensure secure wall mounting. The rate shall be inclusive of all materials, , specialized framing labor, protective packaging, and installation at the designated site as per the instructions of the Engineer-in-Charge.

Wall Art canvas paintings (36 in x 48 in): Supplying and providing a Premium Wall Art canvas paintings,with a nominal size of 91 cm x 122 cm (36 in x 48 in), featuring intricate hand-painted tribal motifs, design, art, color palette and texture as per approved . Each artwork shall be stretched on a high-quality 380 GSM poly-cotton canvas and enclosed in a sleek 25 mm thick black charcoal-finish synthetic or wooden frame with a 2 mm clear float glass or high-transparency acrylic facing to protect the art from dust and UV rays. The assembly must include a sturdy MDF backboard (8 mm thick) with heavy-duty hanging hardware (D-rings and wire) to ensure secure wall mounting. The rate shall be inclusive of all materials, , specialized framing labor, protective packaging, and installation at the designated site as per the instructions of the Engineer-in-Charge.

Premium White Marble Mandir: Supplying, providing, and fixing a Premium White Marble Mandir of approximate overall size 213 cm (L) x 91 cm (W) x 213 cm (H) (7' x 3' x 7'), meticulously crafted from first-quality Makrana Albeta or high-grade Ambaji White Marble, featuring three tiered Shikhars with traditional Kalash motifs, intricate CNC and hand-carved floral Jali toran arches, and heavy-duty square pillars with deep relief carving and traditional base and capital moldings. The structure shall be supported by a raised base (Adhisthana) featuring high-relief carvings of traditional motifs on the front fascia. All surfaces must be mirror-polished with specialized marble wax, with seamless joints filled with matching marble epoxy and ground flush, inclusive of all material costs, specialized carving labor, transportation, and assembly at the designated site as per the instructions of the Engineer-in-Charge.

Bath stool: Supply and placement of bath stool, PVC of size 400 x 300 x 250mm of approved shade and make of Neelkamal/ Supreme or equilent.

Bath Bucket: Supply and placement of bath bucket, PVC of 25L capacity of approved shade and make of Nayasa/ Supreme or equilent.

Bath Mug: Supply and placement of bath mug, PVC of 1.5L capacity of approved shade and make of Nayasa/ Supreme or equilent.

Mirror with shelf: Supply and placement of Mirror with shelf of size 900 x 600 mm made out of teak wood 20 x20mm with 5mm thick mirror with 6mm thick plywood at back and 1 shelf of size 230 x 230 x200mm made out of 18mm thick plywood with 1 mm lamination complete with spirit polish etc. all complete as directed by the Engineer-in-chrage

Waste paper basket: Supply and placement of PVC Waste paper basket

Receptacle (dust ben): Supply and placement of Receptacle of size 270 mm at bottom and 350mm at top round in shape with lid and Mechanism to operate with feet made out of PVC etc., complete all as directed by Engineer -in- charge.

Planter Pot (105 cm Dia): Supplying and providing a Premium Architectural Indoor Planter Pot of approximate overall size 105 cm (Dia) x 60 cm (H), featuring a contemporary low-profile pedestal as per approved design. The planter shall be constructed from high-grade Fiberglass Reinforced Plastic (FRP) or lightweight reinforced GRC (Glass Fibre Reinforced Concrete) with a smooth, non-porous surface finished in premium automotive-grade matte white paint. The unit must feature a broad, circular basin with a reinforced rim and a stable, integrated circular base to ensure structural balance when fully loaded. The interior shall be treated with a bituminous waterproof coating and provided with a functional drainage hole and a matching concealed drip tray to prevent water seepage on interior flooring. The rate shall be inclusive of the planter unit, internal waterproofing, protective padding at the base, , and delivery to the designated site as per the instructions of the Engineer-in-Charge.

Planter Pot (18" x 18" x 18"): Supplying and providing a Premium Rectangular Indoor Planter of approximate size 45 cm (L) x 45 cm (W) x 45 cm (H) (18" x 18" x 18"), designed with clean linear edges as per the requested rectangular profile. The planter shall be fabricated from high-grade Fiberglass Reinforced Plastic (FRP), ensuring a lightweight yet durable structure with a smooth, non-porous surface finished in premium automotive-grade matte white paint. The unit must feature an integrated internal bracing system to prevent bowing when filled with soil, and the interior shall be treated with a bituminous waterproof lining. It shall include a functional drainage system with a concealed internal reservoir or drip tray to ensure no water leakage on the interior floor finish. The rate shall be inclusive of the planter unit, internal waterproofing, , and delivery to the designated site as per the instructions of the Engineer-in-Charge.

Oval Indoor Planter: Supplying and providing a Premium Oval Indoor Planter of approximate size 45 cm (L) x 45 cm (W) x 60 cm (H) (18" x 18" x 24"), featuring a soft-edged elliptical profile as per the requested shape. The planter shall be fabricated from high-grade Fiberglass Reinforced Plastic (FRP) for a seamless, lightweight, and durable construction, finished in premium automotive-grade matte white paint with a smooth, non-porous surface. The interior shall be treated with a bituminous waterproof lining to prevent moisture migration and shall include an integrated drainage system with a concealed internal tray to protect interior flooring from water overflow. The design shall ensure structural stability through a reinforced base and thick sidewalls to maintain the elliptical form when fully loaded with potting media. The rate shall be inclusive of the planter unit, internal waterproofing, , and delivery to the designated site as per the instructions of the Engineer-in-Charge.

Cylindrical Indoor Planter: Supplying and providing a Premium Cylindrical Indoor Planter of approximate size 46 cm (Dia) x 61 cm (H) (18" x 24"), featuring a sleek, perfectly vertical profile. The planter shall be fabricated from high-grade Fiberglass Reinforced Plastic (FRP) to ensure a lightweight yet high-strength structure, finished in premium automotive-grade matte white paint with a smooth, non-porous surface. The interior shall be treated with a bituminous waterproof lining to prevent moisture migration and shall include an integrated drainage system with a concealed internal tray to protect interior flooring from water overflow. The design shall feature a reinforced flat base for maximum stability and a uniform wall thickness to maintain a perfect geometric form when fully loaded with soil. The rate shall be inclusive of the planter unit, internal waterproofing, , and delivery to the designated site as per the instructions of the Engineer-in-Charge.

Terracotta Planter: Supplying and providing a Premium Terracotta Planter of approximate size 61 cm (Dia) x 76 cm (H) (24" x 30"), handcrafted from high-quality, high-fired natural clay for a classic earthen aesthetic. The planter shall feature a traditional tapered profile with a reinforced rim for structural strength and a thick-walled construction to ensure natural breathability for root health. The exterior shall be finished in a natural terracotta matte texture, treated with a transparent water-repellent breathable sealer to prevent excessive salt efflorescence while maintaining the organic look. The unit must include a large central drainage hole at the base and be supplied with a matching heavy-duty terracotta saucer to manage water runoff. The rate shall be inclusive of the handcrafted planter, weather-resistant sealing treatment, matching saucer, , and careful transportation to the site to prevent breakage as per the instructions of the Engineer-in-Charge.

KITCHEN EQUIPMENTS

SS Double Bowl Sink Unit.The top shall be made of 20 SWG SS 304 with 150mm high back splash. The Sink shall be made of 20 SWG SS 304. Frame work will be made of mild steel and dully painted rust proof. The legs will be made of 20 gauge ss 304 square 40 mm pipe. Nylon bullet fit for adjustment 900 x 600 x 850 + 150 Spl. Make : JB EQUIPMENTS / MODERN RASOI SOLUTIONS PVT. LTD / INGNUUS OVERSIUS PVT. LTD

SS Dirty Dish Landing Table With Garbage Chute. (L.H.S) TOPS: Made of 20 Swg. 304 Quality, 20/8 Grade Stainless Steel duly 120 grit matt polished with all edges rounded with no bur or other excess material left. Top will be turned down 50mm The undersides will be suitably sound deadened by treating with silver paint. UNDERSHELVES: Undershelves wherever called for will be constructed of 304 Quality Grade,20 Swg. Stainless Steel Sheeting uniformly matt polished with 120 grit and reinforced with 30mm x 30mm x 18 swg. St. steel square pipe Frame. All shelves will be turned down 38mm and 12mm underneath on all sides with resulting corners cutout to fit contour of legs. Shelves for hot case will be perforated. 600 x 600 x 850 Make : JB EQUIPMENTS / MODERN RASOI SOLUTIONS PVT. LTD / INGNUUS OVERSIUS PVT. LTD

POTATO PILLER Comprising: 20 GA SS body, electrically operated with electric motor of Power : 1 HP, 220V of ISI mark, 10 KG Make : JB EQUIPMENTS / MODERN RASOI SOLUTIONS PVT. LTD / INGNUUS OVERSIUS PVT. LTD

WET GRINDER 10 KG Fitted with Frame, of Stainless steel 304. The grinding portion shall be made out of hard black granite. Bottom Body & Drum made out of stainless Steel of 18 gauge. The grinder shall be attached with single phase 2 HP motor. 20 KG Make : JB EQUIPMENTS / MODERN RASOI SOLUTIONS PVT. LTD / INGNUUS OVERSIUS PVT. LTD

Two range burner Made of Top & Splash 1.5mm Thick Ss 304 Grade With Matt Finish, Sides : 1.0 Mm Thick Ss 304 Grade With Mirror Finish, Leg: 1.5” &1” Ss Square 304 Grade With Mirror Finish And Adjustable Bullet Leg. The gas Burner shall be of T-15 high pressure Burner with heavy duty Iron Casting square panspot. 1200X600X600 Make : JB EQUIPMENTS / MODERN RASOI SOLUTIONS PVT. LTD / INGNUUS OVERSIUS PVT. LTD.

Tandoor (Coal Operated) TOP: 18 Swg s.s. sheet,304 grade 18 SWG 900 x 900 x 1000 Make : JB EQUIPMENTS / MODERN RASOI SOLUTIONS PVT. LTD / INGNUUS OVERSIUS PVT. LTD

Chapatti Plate/Puffer (R.H.S) Top Grilled puffer covered with 16 SWG Polished SS 304, Front & sides Turned Down 50mm & In 12mm, Sound Deadned with Spillage trays : 20 swg SS 304 tray in 2 equal sections. Undershelves : 18 Swg SS 304 undershelf. 100mm rear body/legs setback for gas pipe routing Legs : 4 nos. legs 1-1/2"X 1-1/2"X16 swg SS 304 square with adustable nylon Bullet Feet.900 x 600 x 850 Make : JB EQUIPMENTS / MODERN RASOI SOLUTIONS PVT. LTD / INGNUUS OVERSIUS PVT. LTD

Dosa Plate Top - 16 mm MS Plate Body: 16 SWG Stainless Steel Sheet Cladding with MS angle Frame Burner: 4 RV burner with center coupling, NC valve, and copper pipe with pilot lamp Shelves: (1) One Nos 18 SWG Stainless Steel Legs: (4) Four Nos 16 SWG Stainless Steel Square Pipes Bush: (4) Four Nos Adjustable Square Nylon Bush.900 x 600 x850 Make : JB EQUIPMENTS / MODERN RASOI SOLUTIONS PVT. LTD / INGNUUS OVERSIUS PVT. LTD

Masala Trolley Top of trolley- 1.5mm Thick Ss 304 Grade With Matt Finish, Leg: 1.5” Ss 304 Grade With Mirror Finish And Movable Wheel, There shall be 1/6 GN Pan-6 Nos of required depth with proper individual lead in all 6 pans. 500 x 750 x700 Make : JB EQUIPMENTS / MODERN RASOI SOLUTIONS PVT. LTD / INGNUUS OVERSIUS PVT. LTD

DEEP FAT FRYER TABLE TOP STD table top modle Make : JB EQUIPMENTS / MODERN RASOI SOLUTIONS PVT. LTD / INGNUUS OVERSIUS PVT. LTD

WATER COLLER Storage Capacity (ltr.)- 80 Litres No of Cold water taps- 2 (Brass) Refrigerant- R-134a/R-22 Compressor- Hermetic type or EMERSON with suction gas cooled motor, equipped with overload protector. Thermostat- Automatically controls temperature Power Supply- 230 volts+-10%, 50Hz Single phase. 80 LTR. Make : JB EQUIPMENTS / MODERN RASOI SOLUTIONS PVT. LTD /INGNUUS OVERSIUS PVT. LTD

Sandwich griller double STD Make : JB EQUIPMENTS / MODERN RASOI SOLUTIONS PVT. LTD / INGNUUS OVERSIUS PVT. LTD

Microwave oven STD Cap: 25Ltrs MAKE : LG / IFB / SAMSUNG

Juicer STD Make : JB EQUIPMENTS / MODERN RASOI SOLUTIONS PVT. LTD / INGNUUS OVERSIUS PVT. LTD

SALAMANDER STD Make : JB EQUIPMENTS / MODERN RASOI SOLUTIONS PVT. LTD / INGNUUS OVERSIUS PVT. LTD

SS Hot Bain-marie [4 GN Pan] Top- 1.5mm Thick Ss 304 Grade With Matt Finish , Tank : 1.2mm Thick Ss 304 Grade With Matt Finish, Three Side & Bottom Shelf : 1.0 Mm Thick Ss 304 Grade With Mirror Finish, Leg: 1.5” Ss Square Pipe 304 Grade With Mirror Finish And Adjustable Bullet Leg Vessel : GN Pan 3 no. of 1/1 - 150mm deep ( 21x13x6 inches) 1NO. 1/2 GN PAN Electric Heater of 3kw Heater With Control Unit. 1500 x 650 x 850 + 300 Make : JB EQUIPMENTS / MODERN RASOI SOLUTIONS PVT. LTD / INGNUUS OVERSIUS PVT. LTD

Soiled dish collection trolley Top should be 20 Gauge, SS 304 GRADE shelves should be made of 22 Guage SS sheet, 38x38x3mm SS angle frame supported, noise free rubber castors to be provided with wheels 600 x 1175 x700 Make : JB EQUIPMENTS / MODERN RASOI SOLUTIONS PVT. LTD / INGNUUS OVERSIUS PVT. LTD

DEEP FREEZER:200 LTR 50mm thick PU foam on all sides with plastric material body. 1 KW 220 V AC all complete as per manufacturer specifications 200 LTR. Make : JB EQUIPMENTS / MODERN RASOI SOLUTIONS PVT. LTD / INGNUUS OVERSIUS PVT. LTD

SS Storage Rack Made of 304 Quality, Shelves will be made of 304 Quality 20/8 Grade, 20 Swg. Shelves: 5 Nos, 20 Swg. Stainless Steel. Upright of 30 mm stainless steel square pipe fitted with nylon bullet fit. 900 x 450 x 1650 Make : JB EQUIPMENTS / MODERN RASOI SOLUTIONS PVT. LTD / INGNUUS OVERSIUS PVT. LTD

Air Curtain. 4 feet. STD As per site door dimensio

Insect o Killer STD

Garbage Trolley. 50 Litres STD

SS. Exhaust Hood with SS baffel filters (Wall Type) and GI ducting and exhaust fan MADE OF 20 SWG. 304 GRADE S.S. SHEET, FILTER: FRAME OF 20 SWG.STAINLESS Steel BAFFLE TYPE GREASE FILTER 3900X900X 450 Make : JB EQUIPMENTS / MODERN RASOI SOLUTIONS PVT. LTD / INGNUUS OVERSIUS PVT. LTD

GLASSWARE CROCKERY CUTLERY & UTENSILS

Quarter Plate

Bowl Katori

Tea Saucer

Soup Bowl

Tea Cup

Service Spoon

AP Spoon

AP Knife

Teaspoon

AP Fork

Full Plate

Napkin Holder

Salt & Pepper Dispenser

Straw Holder

ToothPick Holder

Pilsner Glass

Soup Spoon China

Tea Flask

Tea Flask (1 Ltr)

Curry Bowl

Juice Glass

Chutney / Sauce Bowl

Roti Basket SS

Glass Tray Plastic

Chafing Dish

Chafing Dish Hydraulic

Rice Bowl DBL Portion

Roti Basket Soup Tureen

Soup Laddle

Flat Laddle

Garnish Tray

Bread Tong

Food Pan

Salver

Glass Bottle 1ltr.

MEP WORK

INTERNAL ELECTRIFICATION

Supply of STRIP LED 30W/5M pack with non integral / integral driver, 6500K color temp having 50000 burning hrs life with accessories suitable for operation on 220 V to 240 V supply as required as per direction of Engg.-in-Charge. (Make: Philips/Wipro/Crompton/LT/Jaquar).The luminaire shall bewith Replacement Warranty of 2 years.

Supplying of focus cob led 12w with non integral / integral driver, 6500K color temp having 50000 burning hrs life with minimum efficacy > 120 lm/W. Suitable for operation on 220 V to 240 V supply as required as per direction of Engg.-in-Charge. (Make: Philips/Wipro/Crompton/LT/Jaquar).The luminaire Shall be with Replacement Warranty of 2 years.

Supplying of wall Mounted chrome finish Wall lamp(for bed light) with 1 light forsted glass comprising of 7W with non integral / integral driver, 6500K color temp having 50000 burning hrs life with minimum efficacy > 120 lm/W. Suitable for operation on 220 V to 240 V supply as required as per direction of Engg.-in-Charge. (Make: Philips/Wipro/Crompton/LT/Jaquar).The luminaire Shall be with Replacement Warranty of 2 years.

Supplying of Centourus Chandller with Asfour Almaaza Crystal & Gold Finish (D 1470* H1900MM) Wattage: 30 X 4W LED,Zinc Alloy with natural Jade,Asfour Almaaza Crystal MODEL NO-DTO-GLD-ASCEN1771230C.Make:Jaquar/Philips or equevalent make as required.(for Ground floor .)

Supplying of 80w high bay luminaire with Aluminium Die Cast housing,Color Temperature (K) -5700 K,Surge Protection (kV)(Internal)-6 KV,CRI Not less than 70, Led life-100000 Hrs, 150 lm/w efficacy with internal Driver,etc as required. Manufacturer mandatory i/c connection wire, testing etc. to complete the joband all other accessories suitable for operation on 220 V to 240 V supply as required as per direction of Engg.-in-Charge. (Make: Philips/Wipro/Crompton/LT/Jaquar)

Supplying of wall Mounted non -corrosive aluminium body with high lumen output LEDs of 3W with non integral / integral driver, 6500K color temp having 50000 burning hrs life with minimum efficacy > 120 lm/W. Suitable for operation on 220 V to 240 V supply as required as per direction of Engg.-in-Charge. (Make: Philips/Wipro/Crompton/LT/Jaquar).The luminaire Shall be with Replacement Warranty of 2 years.

Supplying of Silver Black 450mm wall bracket fan with louvre. (Make:Bajaj/Usha/ Crompton/ Orient/ Khaitan/ Havells) as required.

Supplying of Exhaust fan / fresh air fan with louvre as required. (Make : Crompton/ Orient/ Havells/Bajaj/Usha)

Smart Ventilair White 200 mm sweep fibre body fresh air fan

450 mm sweep heavy duty metalic body fresh air fan

Installation, Testing and Commissioning of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.Upto 450 mm sweep.

Supplying and fixing 2.4 GHz Digital Splitters used for splitting a single coaxial line into 2, 3, or 4 lines. Splitters shall support the 1 Ghz to 2.4 GHz frequency range for satellite and on-demand cable television services.(Make :Havells/Finolex/Anchor/Legrand/Commscope)

Supplying, installation, testing & commissioning of 5 Star rated compact mini bar with 47 litr refrigerator with Eco friend designed for hotel rooms. with all acessories.(Make: bluestar/samsung/voltas/lg)

Supplying, installation, testing & commissioning of 800w-1000 watt light weight stim Iron with non stick coating and 1.8 m cord . Make:Philips/Crompton/Bajaj.

Supplying, installation, testing & commissioning of 12 Kg, 5 Star, fully automatic front loading washing machine with In-Built Heater, Onyx Black)MODEL NO- FHP1412Z3, Make: SAMSUNG/ LG /PANASONIC/BLUESTAR/IFBOX/BOSCH

Supplying, installation, testing & commissioning of 500-Litter ,5 Star rated Automatic Visi Cooler with Glass Door Commercial Refrigerator (500 L)(Make: Bluestar/Voltas/Samsung/Western or equivalent)

LED TV

Supplying, Installation, Testing and Commissioning of 42 inch LED TV with 3840x2160 resolution or better, USB playback, bluetooth and miracast connectivity, 4X HDMI 2.0, DP 1.2, HDR 10/10+, brightness: 500-nitsor better, Video wall mode should be available, contrast ratio: 1200:1, OPS slot, viewing angle (H/V): 170°/ 170°, response time less than 12ms with remote as required with 3 years onsite warrenty. Make: SAMSUNG/ LG /SONY/PANASONIC.

Supplying, Installation, Testing and Commissioning of 55 inch LED TV with 3840x2160 resolution or better, USB playback, bluetooth and miracast connectivity, 4X HDMI 2.0, DP 1.2, HDR 10/10+, brightness: 500-nitsor better, Video wall mode should be available, contrast ratio: 1200:1, OPS slot, viewing angle (H/V): 170°/ 170°, response time less than 12ms with remote as required with 3 years onsite warrenty. Make: SAMSUNG/ LG /SONY/PANASONIC.

Supplying, Installation, Testing and Commissioning of 75 inch LED TV with 3840x2160 resolution or better, USB playback, bluetooth and miracast connectivity, 4X HDMI 2.0, DP 1.2, HDR 10/10+, brightness: 500-nitsor better, Video wall mode should be available, contrast ratio: 1200:1, OPS slot, viewing angle (H/V): 170°/ 170°, response time less than 12ms with remote as required with 3 years onsite warrenty. Make: SAMSUNG/ LG /SONY/PANASONIC.

20KVA UPS FOR ELV AND EMERGENCY LIGHTING

SITC of 20KW true online double conversion UPS system having 3 Ph. 415 V AC, 50 Hz Input & 415V, 50Hz 3Ph Output unity power factor. Comes with inbuilt Galvanic isolation transformer with inbuilt Phase reversal correction, SNMP card for remote monitoring and UPS should have Type 2 SPD of Fault current 40kA, 3 phase rating having protection level < 1KV, response time < 0.5 nano sec, All Mode Protection (L-L / L-G / L-N / N-G), response time < 0.5 nano sec., EMI/ RFI attenuation: 40 dB Certification - Listed with IEC/EN 61557-3 ; IEC/EN 61010:1 ; IEC/EN 61000-4-13. And It shall consist of Earth status indicator facility Continuous LED display of earth status, Green LED indicate to correct earth status, Yellow LED indicate to Poor earth status and Red LED indicate to Disconnect or No earth status . Designed according to the most exacting standards. Intelligent protection. And should be 50 Degree Operating Temperature. Including (32 nos. 12V *42AH SMF VRLA Battery Total VAH 16128) for 30 min back up with Rack and accessories. And Battery charger should be suitable to charge Lithium-ion Battery. The OEM should have their own office & Service Center at Orissa and The Bidder needs to submit the Service Tax Registration Certificate of OEM. Make: EMERSON/APC/ VERTIV/ SCHNEIDER/ NUMERIC. Warranty: 1 Year.

6KVA UPS FOR AV

SITC of 6KW true online double conversion UPS system having 3 Ph. 415 V AC, 50 Hz Input & 230V, 50Hz 1Ph Output unity power factor. Comes with inbuilt Galvanic isolation transformer, SNMP card for remote monitoring and UPS should have Type 2 SPD of Fault current 40kA, 3 phase rating having protection level < 1KV, response time < 0.5 nano sec, All Mode Protection (L-L / L-G / L-N / N-G), response time < 0.5 nano sec., EMI/ RFI attenuation: 40 dB Certification - Listed with IEC/EN 61557-3 ; IEC/EN 61010:1 ; IEC/EN 61000-4-13. And It shall consist of Earth status indicator facility Continuous LED display of earth status, Green LED indicate to correct earth status, Yellow LED indicate to Poor earth status and Red LED indicate to Disconnect or No earth status . Designed according to the most exacting standards. Intelligent protection. And should be 50 Degree Operating Temperature. Including (16 nos. 12V *26AH SMF VRLA Battery Total VAH 4992) for 30 min back up with Rack and accessories. And Battery charger should be suitable to charge Lithium-ion Battery. The OEM should have their own office & Service Center at Orissa and The Bidder needs to submit the Service Tax Registration Certificate of OEM. Make: EMERSON/APC/ VERTIV/ SCHNEIDER/ NUMERIC. Warranty: 1 Year.

Supplying and fixing following rating RCBOs/ MCBs in the existing DB complete with connections,testing and commissioning etc. as requiredMake-LK -EXORA/ABB-SB200i/Legrand(DX3)/siemens(Betaguard)/Schneider Acti9)

Supplying and fixing 63Amps 3P+N 415 volts, MCB in the existing MCB DB in the existing MCB DB complete with connections as per direction of Engg.-in-Charge. The MCB should be Replacement Warranty will be 1 years.

Supplying and fixing 40Amps 3P+N 415 volts, MCB in the existing MCB DB in the existing MCB DB complete with connections as per direction of Engg.-in-Charge. The MCB should be Replacement Warranty will be 1 years

Supplying and fixing 40 amps,30ma rating, 240 volts, C series, Double poles RCBO of in the existing MCB DB complete with connections as per direction of Engg.-in-Charge. The MCB should be Replacement Warranty will be 1 years .

Supplying and fixing 32 amps,30ma rating, 240 volts, C series, Double poles RCBO of in the existing MCB DB complete with connections as per direction of Engg.-in-Charge. The MCB should be Replacement Warranty will be 1 years .

Supply and laying of 25/32mm UPVC trunking system and acessories.(Make:Legrand/MK(honeywell)

LIGHTNING PROTECTION SYSTEM

Air Terminal

Supply , Installation, Testing & commissioning of 8 mm Aluminum Round Conductor. Tested as per IEC 62561. (Make:OBO/ABB/DEHN)

Supply , Installation, Testing & commissioning of Roof conductor holder for parapet- Polyamide Conductor holder: With M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder. Weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor holder @ 1 meter distance. Tested as per IEC 62561. (Make:OBO/ABB/DEHN)

Supply , Installation, Testing & commissioning of Polyamide roof cable holder for flat roof:DIN 48829 Form B1. Closed form with bottom. Filling weight 1Kg (frost-resistant concrete). Sleeve from polyethylene, black @ 1 meter distance. Tested as per IEC 62561. (Make:OBO/ABB/DEHN)

Supply , Installation, Testing & commissioning of cross universal connector: For T and cross connection, to route vertical down conductor /mesh formation made of hot dipped galvanised iron with necessary screws etc as required. Installed with 4 hexagonal bolts M8*25 with M8 hexagonal nuts . Tested as per IEC 62561. (Make:OBO/ABB/DEHN)

Supply , Installation, Testing & commissioning of expansion piece with connector: For equalising temperature related length changes. Necessary on conductors length over 20 meters. For round conductor Rd 8/ALU. Tested for 100kA lightning current. (Make:OBO/ABB/DEHN)

Supply , Installation, Testing & commissioning of Connector: For T cross and parallel connectors. Quick installation using hexagonal bolt M10X30 high-grade hot dip galvanised. Tested as per IEC 62561.(2nos/expansion piece ).(Make:OBO/ABB/DEHN)

Supply , Installation, Testing & commissioning of 1 mtr vertical air terminal with mounting accessories on the flat surface to meet the requirements of IS/IEC 62305. Tested for Electrical , mechanical and chemical as per IEC 62561. Tested for 100kA lightning current. (Make:OBO/ABB/ DHEN).

Supply , Installation, Testing & commissioning of Vertical air terminal with accessories:Providing of Air terminals as per IS-IEC -62305 part-3 Nominal size Ø10/16 mm aluminium rod: 2 Mtr Airterminal: semi-hard (E-AlMgSiO5 corresponds to DIN 48801) Suitable for high wind load. Tested as per IEC 62561. (Make:OBO/ABB/ DHEN).

Supply , Installation, Testing & commissioning of Stand for Fang Fix system 16 kg with base and clamp ,made up of frost resistant concrete and clamp tested upto 100KA lightning current . (Make:OBO/ABB/DEHN)

Supply , Installation, Testing & commissioning of Stand for Fang Fix system 16 kg made up of frost resistant concrete. (Make:OBO/ABB/DEHN)

Down conductor

Supply , Installation, Testing & commissioning of 8 mm Aluminum Round Conductor. Tested as per IEC 62561. (Make:OBO/ABB/DEHN)

Supply , Installation, Testing & commissioning of Polyamide Conductor holder: With M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder. Weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor holder @ 1 meter distance. Tested as per IEC 62561. (Make:OBO/ABB/DEHN)

Supply , Installation, Testing & commissioning of Test Joint (Folding Clamp) suitable to connect 8mm round conductor and max by 30x3 mm GI strip as specified in drawing and directed by Engineer. Tested for 100kA lightning current. (Make:OBO/ABB/DEHN)

Ring & vertical earthing system

Supply , Installation, Testing & commissioning of Galvanised Steel Flat 30X3 mm thickness from earth electrode directly in ground as required. Flat conductor Hot Dipped Galvanized. Tested as per IEC 62561. (Make:OBO/ABB/DEHN)

Supply , Installation, Testing & commissioning of Cross connector for Flat: Suitable for 30mm Galvanised steel strip. Installed with 4 nos of hexagonal plate. Tested for 100kA lightning current. (Make:OBO/ABB/DEHN)

Supply , Installation, Testing & commissioning of flat conductor holder- Fit: FL 30, With mounting hole 6.2 x 22 mm, With 2 cylinder bolts M6 x 16 and over-piece from hot-dip galvanised steel, Bottom section from polyamide, black. Tested as per IEC 62561. (Make:OBO/ABB/DEHN)

Supply , Installation, Testing & commissioning of Plastic Corrosion Protection strip: Approx 1.1 mm thick. Width 50mm. Made of petrolatum- coated chemical fibre fabric.(Make:OBO/ABB/DEHN)

Supply , Installation, Testing & commissioning of UL Listed maintenance free ,Low carbon copper coated earth rod of 3 metre electrode having diameter of 14.2 mm with copper coating thickness of 250micron tested as per IEC 62561-2 (Make:OBO/ABB/DEHN) Supply , Installation, Testing & commissioning of universal clamp made of SS to connect rod with flat conductor (Make:OBO/ABB/DEHN) Supply , Installation, Testing & commissioning of Earth conductivity enhancing mineral compound shall be of 25 kg/pit tested as per IEC 62561-7,TCLP tested (Make:OBO/ABB/DEHN) Supply , Installation, Testing & commissioning of The above arrangements shall be provided with Heavy duty earth champer of 5000kg load bearing capacity to ensure the safety of earthing system (Make:OBO/ABB/DEHN).

EXTERNAL ELECTRICFICATION

SITC of 45W Decorative post top Luminaires BIS approved for Urban lighting, Composed of an aluminum body sealed with a deep polycarbonate protector, , Fixture Dimension -height 620 mm +- 5% and width as 488X 488mm ,weight should not be less than 11.5 kg +- 5 % and 70(Typ), <= 5 SDCM Luminaire can be installed as a suspended luminaire . The luminaire is equipped with PMMA lenses with wide photometry for increased pole spacing. The luminaire is provided with internal surge protection of 4 KV .Fixture is having external surge protection of 10KV. Electronic driver is having power factor>0.90, THD <10 % and input voltage range from 110-277V AC at 50/60Hz. Minimum lumen 5000 lumens in CCT range of 3000/4000 as per ANSI,LED Make CREE/Osram/Samsung/APT with LM80 report to be submitted at the time of Supply , life of 50000 burning hours with 70% of initial lumens maintained. Ambient Operating Temperature is -40 Deg. to 50 Deg. Luminaire should Maintain Ingress Protection of IP65 for better weather proofing. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Both the fixture and Driver should have separate BIS approval. with 4 M Die cast / decorative pole (MAKE: klite/Philips/Wipro/Reytek)

Supply and fixing of Architectural bollard LED 3000K 230-240Vac 50-60Hz CRI > 70 Input power: 8W,800lm, Height 800mm, IP rating IP65, impact resistance IK7. MATERIAL CHARACTERISTICS : Extruded aluminium bottom pipe Ø100 x H800mm with polycarbonate diffuser and integral base plate Ø180 with PG gland. Operating ambient temperature range is from -20°C to +40°C. Resistance to heat and fore for plasticpart should be 850 degree celcius. Housing Color Dark grey RAL 7043. CCE, CE and RoHS compliance. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted.(MAKE: (MAKE: klite/Philips/Wipro/Reytek)

Supply and fixing of Surface mounted 12w, compact spot light designed to provide directional light. Beam angle 15° / 25° / 40°. Luminaire made of pressure die cast aluminium alloy of high corrosion resistance and non corrosive stainless steel fasteners. Clear toughened glass of 4mm thickness. Hybrid optics with lens & mirror finish pure aluminium reflector combination for higher efficiency, lower optical losses with optimum glare suppression. Swivel range of 0°-90°. Single cable entrance M10 cable gland. Protection class IP66. Mechanical resistance IK06. Pure polyester powder coated RAL 9004 Signal black, RAL9007 Grey aluminium, RAL 7016 Anthracite grey, Graphite grey. Available colour temperature 2700K / 3000K / 4000K / 5700K, Colour rendering index (CRI)>80. K-Lite LED module with expected service life of at least 60,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Luminaire dimension : 101mm length x 64mm width x 93mm height. CE & BIS Certified. Inhouse NABL accredited lab. (MAKE: (MAKE: klite/Philips/Wipro/Reytek)

SITC of 8w, floor recess mounted compact in-ground luminaire. Asymmetrical light distribution. Polycarbonate optical lens for higher efficiency, lower optical losses with optimum glare suppression. Pressure die-cast aluminium housing, Stainless steel top ring (grade 316) with toughened glass. Polypropylene Black installation housing for preparing the recess opening in ground. Single cable entrance via grey M10 cable gland. All external screws are made of stainless steel. Clear silicone gasket. Protection class IP67. Mechanical resistance IK08. Available colour temperature 2700K / 3000K / 4000K / 5700K, Colour rendering index (CRI)>80. K-Lite LED module with expected service life of at least 60,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Luminaire dimension : 88mm diameter x 118mm height. CE & BIS Certified. Inhouse NABL accredited lab. (MAKE: (MAKE: klite/Philips/Wipro/Reytek)

Supply, Installation, Testing & Commissioning of 6W step Light with Integral driver & completely made in India luminaire. The luminaire’s shall be made of Die cast aluminum with Pure polyester powder coated housing. Optical compartment is sealed Reflector with toughened glass using Silicon gasket ensuring IP65 and lifelong performance.The LEDs shall have minimum CRI ≥80 (White LED) & shall have SDCM≤5. The luminaire shall have wattage 6W and fixture shall having operating temperature range of 0°C to 45°C. Input Voltage Range of 150 - 270V AC. 2 stage The luminaire shall have declared life of 50,000 burning hours at L70. Luminaire and Driver must be made in India with same brand. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer along with technical bid. LM80 , RoHS compliance issued by LED luminaire manufacturer, BIS certificate for LED Luminaire. Brand name shall be embossed / engraded on each an every light fixtures. Luminaire and Driver should be Made in India. Luminare, Driver and controller should be with same (MAKE: (MAKE: klite/Philips/Wipro/Reytek)

SITC of waterproof powerjunctionbox /powercableterminalbox, IP65 made up of rugged,non corrosive, highimpact polycarbonate, molded nylon encases connectors that uses crew compression to secure the wires, protection against water jets and dust from all directions,includes5Way min10A connector terminal block Max. dimension : 80 * 250 * 85mm .

Transformer(11/.433KV TRANSFERMER)

Supplying installation testing and commissioning of 500 KVA 11/0. 415 KV 3 Phase, 50Hz, Dyn11, oil cooled ONAN type, outdoor type, copper wound transformer Confirming to IS:1180(Part-I), 2014 and latest Energy Efficiency Level-II with OFF load tap changing arrangement on HV side from + 5% to -10% in steps 2.5% along with cable end box on HT side on LT side, complete with buchlotz relay, oil and winding temperature indicator and alarm contact, PRV, MOG with all accessories i/c first filling of filtered dehydrated oil with as per specification attached complete in all respects. Make-OTPL/OEU/ALFA/CG

Construction of Transformer plinth size 1.8 Mtr X1.7 Mtr and above groun finished height of 1.2 mtr and 600 mm below ground with 250 mm width brickwall all aound duly plastered with sand filling at te center ,6" depth RCC Slab in TOP,including foundation work with PCC , Brick work etc as required.

11 kV, RING MAIN UNIT WITH All Motorized, M+CT2CT2 (Bus Metering+2LBS + 1VCB)3-WAY RMU UNIT

DG Set(250*2KVA)

SITC of 415V,50Hz, 500 kVA (2x250 kVA)Diesel Generator Sets complies to CPCB IV Polution Standard along with AMF, Synchronization Relays ,Load Manager and Panel Comparises of 2nos-500Amp Electrically Operation MCCB with O/L ,S/C,E/F Protect and 1no-800Amp Electrically operation ACB With O/L,S/C,E/F Protection Complete with : a) Fuel Tank. b) Batteries and leads c) Silencer d) AVM Pads e) Acoustc Enclosure f) Panel g) First fill of Lube oil as required.

SITC of of Acoustic enclosure for 250*2 KVA DG Set

SITC of of Load Side Terminal Box

SITC of of Standard manual Control panel (As per attached BOM)

SITC of exhaust piping of MS B Class exhaust pipes conforming to IS:3589 with welding joint including bends, clamps, dash fastener, flanges, nuts, bolts etc. complete as required

Supply and fixing of 990 liter day Tank of 300mm height with Fuel Pipe fittings like bends, flanges, valves, tee, elbows

DG set as above,Make-Jakson/Mahindra/Kirloskar

Providing and fixing bi-lingual Danger HT notice board of 250mmx200mm as specified below,made of mild steel at least 2mm thick & vitreous enamelled signal red color on both sides as background & with insprictions in enamelled vitreous white color on front side for lettering as required.

supply and making foundation for DG set with MS Joist,Angle ,flat and MS chequred plate for installation of DG Set on a raised platform of height as decided by Engineer-in-charge incuding foundation ,walkway around the DG Set,ladder etc as required.(Note:- Design of structure should be approved by the OEM)

FIRE FIGHTING SYSTEM

Supply & Laying of XLPE power cable of 1.1 KV grade of following size on Cable

3C X 70 sqmm

3C X 16 sqmm

Supply & installation of Hot -dip galvanized cable rack system made of 1.6 to 2mm thick sheet steel folded with two longitudinal side rails connected by rungs at regular intervals of following sizes with necessary Tee's, Vertical/ Horizontal Bends, expansion anchor fasteners, coupler plates, coupling fasteners, Grippler, GI thread rods of required height, including supply & grouting of supports as required at site. The supports should be painted with black enamel paint over a coat of anti corrosive primer. (Tray shall be measured along the central axis of the cable tray). Note: Cost of support shall be included (Distance between one support to other support mini. space 1.2mtr to 1.5 Mtrs gap as per site required). Make-BEC/MEM/ATUL/OBO.

150 mm (W) X 50 mm (H) with 1.2 mm thick sheet

Cable laying Laying & fixing of one no. PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size on Cable Tray as required.

Upto 35 Sqmm

Above 35 Sqmm and upto 95 sqmm

End Termination

Supply & Making end Termination with brass compression gland and aluminium lugs for PVC insulated and PVC sheathed cable of 1.1 kv grade (without cost of Cable)

3C X 70 sqmm

3C X 16 sqmm

PIPE & VALVES ETC.

Supply,Installation,Testing & Commissioning of 150NB Alarm Valve , Water Motor Gong Retarded Chamber, Flange to:- ANSI B 16. 1 Class 125/ANSI B16.5 Class 100, All Components are UL Listed/FM Approved , Rated pressure 17.50 kg/cm2, Test pressure 500PSI confirming to IS :15105:2002 with ISI mark as per direction of Engineer-in-charge. MAKE: ZOLOTO/KARTAR/HGURU/DANFOSS

WET RISER CUM RING SYSTEM

Providing supply & fixing of MS Hose Box for of suitable size(750X600X250mm) to accomodate 2 nos. of 15/ 1 no of 30 mtr long fire hose and a branch pipe, wall mounted type as per direction of Engineer-in-charge. MAKE: OMEX/ NEWAGE / MINIMAX / KARTAR

SPRINKLER SYSTEM

Supply,Installation,Testing & Commissioning of C. I. Sight glass with 25 NB Gunmetal Ball Valve with CI hand wheel ISI Mark for all floors etc. all complete as per direction of Engineer-in-charge. MAKE: NEWAGE / ZOLOTO / KARTAR

Providing & fixing of 25 mm size Gunmetal Pressure Release Valve with isolation valve and all accessories conforming to IS3233:1965 as per direction of Engineer-in-charge. MAKE: NEWAGE / ZOLOTO / KARTAR

FIRE EXTINGUISHER SYSTEM

Portable Fire Extinguisher System Supplying, installation, testing and commissioning of CO2 type Fire Extinguisher 4.5 kg capacity confirming to IS: 2878 made from ISI marked seamless cylinder confirming to IS: 7285, fitted with ISI marked controlled valve confirming to IS: 3224, high pressure 1mtr discharge hose & horn complete with initial gas charged with carrying handle & wall mounting bracket . (Make: superimax/Cese fire/Minimax)

Supplying, installation, testing and commissioning of ABC type fire extinguishers of 6 kg capacity including cost of all material & labour etc complete. (Make: superimax/Cese fire/Minimax)

Supplying, installation, testing and commissioning of Mechanical Foam type 9 litre capacity Fire Extinguisher, ISI marked, IS: 10204, containing 540 ml AFFF liquid ISI marked, IS: 4989 Part II and a polyurethane coated CO2 Gas Cartridge, ISI marked, IS: 4947 complete with gunmetal union cap, nylon hose with plastic foam making branch and wall mounting bracket.(Make: superimax/Cese fire/Minimax)

Fire buckets ( WITHOUT SAND) round bottom type enamel painted, white inside & Red out side and Letter "FIRE" in black out side and handle with mounting bracket.

First Aid Box.

Shock Treatment Chart (Odia / Hindi & English).

8 mm thick Rubber Mat.

Danger Board.

Supplying and drawing of 2X1.5 sq.mm Armoured cable in the existing surface/ recessed conduit with all accessories as per direction of Engineer-in-charge. Approved Make: anchor/ Finolex/ Havells

SITC of Cordless Remote Controller

Supply & Installation Testing and Commission of Control wiring of 2 core x 0.75 sqmm copper cable through MS conduits in between indoor and outdoor units.MAKE:RR/ FINOLEX/ ANCHOR.

Supply, Installation, Testing and Commissioning of hard PVC drain pipe with 9mm thick nytrile tube insulation.(With necessary Lbow, Sockets & Reducers.)MAKE:FINOLEX/ SUPREME/ PRINCE

25mm inner dia

32mm inner dia

Supplying, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/ round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports, bends, transitions, reducers, end caps, collars etc as required complete in all respect in confirmation with IS : 655 and approved drawings and specifications of following sheet thickness complete as required..Make:Sail/Jindal/Tata.

Thickness 0.63 mm sheet

Insulation Work.MAKE:ARMACELL/ A FLEX/K FLEX

Acoustic lining (For Ducts).MAKE:ARMACELL/ A FLEX/K FLEX

Accoustic Insulation 15 mm thick of Armasound antifungal/antibacterial closed cell nitrile rubber. MAKE:ARMACELL/ A FLEX/K FLEX

All Powder coated aluminium Supply & Return Air Grill

Installation of Mouth piece canvass connection :

V.I PAD

Supply and Commissioning of VRF systems including additional referigernt R410A in all respect to complete the system as per site requirements.MAKE:HONEYWELL/ CHILLAIRE/ GFL/ DUPONT

MECHANICAL VENTALATION & LIFT PRESSURIZATION FAN

Supply installation, testing and commissioning of single piece long casing (motor should completely be accommodated inside the fan casing) Vane Axial Fan in MS with powder coated / GSS, Al impeller with adjustable blade angles (Manually Adjustable at Site) and directly coupled TEFC Sq.cage induction motor (IE2) (F-class for smoke Exhaust Air) suitable for 415V±10%, 50 Hz. 3 phase electric supply complete with required hardware etc. All offered fans pitch angle shall be AMCA Certified & Listed on AMCA website (Interpolation of pitch angle shall not be acceptable) and Fan Efficiency Grade ( Min FEG 71, lesser is not acceptable).Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm & Dia 1600 – 5 mm. All fans after assembly shall be dynamically trim-balanced to ISO1940 and AMCA 204/3 - G2.5 quality grade.Fan Casing should be provided with Special Designed Integral Straightening Vanes (Vanes should be integral part of casing, it should not be provided separately as an accessory) to reduced turbulence provide high performance & low noise level.. Make:Kruger/System Air/Mico/GREENHECK.

10000 CFM(Total static pressure-20mm)

Supply installation, testing and commissioning of single piece long casing (Motor should completely be accommodated inside the fan casing, ) Vane Axial Fresh Air Fan in MS with powder coated / MS, Al impeller with adjustable blade angles (Manually Adjustable at Site), bird screen ,gravity louvers, fire retardent flexible connection, necessary nut bolts and directly coupled TEFC Sq.cage induction motor (IE2) H Class insulation for Basement Exhaust/ Smoke Exhaust suitable for 415V±10%, 50 Hz. 3 phase electric supply complete with required hardware etc. All offered fans pitch angle shall be AMCA Certified & Listed on AMCA website (Interpolation of pitch angle shall not be acceptable) and Fan Efficiency Grade ( Min FEG 71, lesser is not acceptable).Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm & Dia 1600 – 5 mm. All fans after assembly shall be dynamically trim-balanced to ISO1940 and AMCA 204/3 - G2.5 quality grade. Make:Kruger/System Air/Mico

8000 CFM(Total static pressure-20mm)

Fans for emergency application Tube axial are to be used. Sound level for emergency operation it should not exceed 88 Db(A)@ 3 meter (Room condition).Incase of not achieving sound , attenutor has to be added. Outlet velocity of the fans should not exceed 16 m/s for emergency application.

Lift well Pressurization -10000CFM (50 MMWG)

Lift well Pressurization -10000CFM (50 MMWG)

Lift well Pressurization -10000 CFM (50 MMWG)

Supply installation, testing and commissioning of Cabinet type Direct driven Forward-Curved Centrifugal Inline Fan with External rotor motor & Speed regulator. Fan is suitable for 1~, 230V, 50 Hz power supply.

1600 CFM fresh air Inline Fan(Total static pressure-20mm)

1600 CFM Exhaust Inline Fan(Total static pressure-20mm)

CO SENSOR

Supply and installation of CO Sensor Detector & Transmitter with UL 94:V2, EMC Directives 2014/30/EU, Impact Resistant IK08, Tough, rugged, glass–fiber reinforced, heavy-duty polycarbonate industrial enclosure, Hydrophobic filter, Expected Life should be minimum 6-10 years in the normal operating environment with serviced regularly.

Each Sensor shall have Output Terminals: (Screw Type)

Measuring range: 0-300 PPM

Sensing element: Electrochemical Diffusion Type

Measuring Gas: Carbon Monoxide Gas

Sensor element (cell): Electrochemical Diffusion, Electrolyte type Gel based.

Response time: ≤ 30 Sec

Protection Class: IP 65

Resolution: 0.5 ppm

Working temperature: -15°C to 50°C

Power supply: 16 - 29 VDC

Analog output signal: 4-20 mA (2-wire)

Coverage area : 465 m2 to 930 m2

Ducting & Grills

Rectangular GI Ducting

Supplying, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/ round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports, bends, transitions, reducers, end caps, collars etc as required complete in all respect in confirmation with IS : 655 and approved drawings and specifications of following sheet thickness complete as required..Make:Sail/Jindal/Tata.

Thickness 0.80 mm sheet sq. m

Thickness 1.00 mm sheet

Pressurization Strater panel

Basement strater Panel

CO GAS monitoring display control panel

Supply and installation of Centralized Gas Monitoring PLC Control HMI Display Control Panel to automatically operate the Fans at 35ppm (TWA Limit) and 100ppm (STEL Limit) of CO gas detected by CO Sensor Transmitter

Microprocessor-based PLC-HMI Master & Slave Control and Monitoring System to automatically operate the Fans. Model: ALVI 6.6.8.2 Required Features: • 6x Analog Input (AI) Channel sensor analog input (4-20mA from Sensor) • 6x Digital Output (DO) (potential-free contacts) • 8x Digital Input (DI) • 2x Analog Output (AO) • HMI Display with Master panel and without HMI in Slave Panel, slave panel should be integrated with the master panel. • Hooter with strobe • Fault relay with normally open contact, potential-free, max. 250 V AC, 5 A • Panel isolation using MCB & Fuse & Alarm Hooter • Fully pre-programmed as per global standards with customer demand • Power unit: 230/110 V AC to 24 V DC, 6.5 A • Interface Modbus RTU RS-485 for Slave Panel • 1x Push button for an alarm reset • Panel isolation using MCB. • Wall mountable Rittal panel ‘UL listing’ German quality • The fully pre-programmed system as per customer demand. Approved Make- ALVI

Panel as above

CABLES & CABLE TRAYS:

CABLES

Supply, laying, testing and commissioning of following sizes of PVC sheathed XLPE insulated Copper conductor armoured cables of 1100V grade on surface of wall or in existing cable trays/masonry ducts/ hume pipe with fixing hardware etc. as required.

3C x 10 Sq.mm cable

3C x 6 Sq.mm cable

Cable termination :

Supply, installation, testing and commissioning of Cable end termination of the following XLPE insulated sheathed Copper conductor armoured cables of 1100 volt grade including supplying and fixing of bimettalic crimping lugs, double brass compression glands with earthing facility and cable sockets etc. complete as required.

3C x 10 Sq.mm cable

3C x 6 Sq.mm cable

Data Networking System

Supply & Laying of Cat6 23Awg UTP Cable, through existing conduit, Make: Legrand/Tyco/Digisol/Commscope.

Supply & fixing of RJ-45Jack of Category 6 with Single-port British-style Face plate 86x86 mm with Curveture and wall mount box Make: Legrand/Tyco/Digisol

Supply , installation, testing & commissioning of Cat6 24 Port Loaded Patch Panel: make:-Legrand/Tyco/Digisol/Commscope.

Supply , installation, testing & commissioning of Cat6 Factory crimpped moulded patch cord, 1mtr, Make : Legrand/Tyco/Digisol/Commscope.

Supply , installation, testing & commissioning of 24 Port1 10/100/1000Mbps L2+ Managed PoE Switch with 4 SFP Ports Make: Cisco/Juniper/Digisol

Supply, Installation,Testing & Commisioning of 24 Port Fiber Optic SFP Managed Switch 10/100/1000Mbps Layer 3 switch includes 4 Gigabit combo ports,additionaln4 x 1G/10G SFP+ ports.Default 2 fixed AC power supply.Make: Cisco/Grandstream/Digisol.

Supply , installation, testing & commissioning of 9U/500Wall Mount Rack with FAN, PDU, Cable manager and H/W Pkt. Make : Legarnd/Valrack/RetailLegrand/Tyco/Digisol/Commscope.

Supply , installation, testing & commissioning of 27U/600Wall Mount Rack with FAN, PDU, Cable manager and H/W Pkt. Make : Legarnd/Valrack/Retail

Supply, Installation, Testing & Commissioning of Full High Definition 5MP( 2880 x 1624) resolution vandal proof Dome camera, 1/3" Progressive Scan CMOS Sensor, IR Cut mechanical Filter for True Day & Night vision, Support dual streams, Onvif supported, IP66 Weather proof outdoor enclosure, Inbuilt Smart IR LEDs with intensity control, IR 30 mtr, H.264 / H.265, Supports android and iOS APP for Smart phone and tablets, with Inbuilt audio, -10°C to + 50°C, CE, FCC, RoHS . Make-HoneywellMake: Cisco/Grandstream/Digisol.

Supply, Installation, Testing & Commissioning of Full High Definition 5MP( 2880 x 1624) resolution vandal proof Bullet camera, 1/3" Progressive Scan CMOS Sensor, IR Cut mechanical Filter for True Day & Night vision, Support dual streams, Onvif supported, IP66 Weather proof outdoor enclosure, Inbuilt Smart IR LEDs with intensity control, IR 30 mtr, H.264 / H.265, Supports android and iOS APP for Smart phone and tablets, with Inbuilt audio, -10°C to + 50°C, CE, FCC, RoHS . Make- Honeywell/Axis/Pelco.

Supply, Installation, Testing & Commissioning of 64Channel fully Featured NVR with High decoding capability for Ultra 4K HD viewing up to MP(4K) resolution live view, Preview & Playback, Internal storage supports 8 HDDs (8TB each). Record bit Rate (320Mbps), 2 HDMI/VGA simultaneous video, usb ports 3 (2 rear USB3.0: 1 front USB2.0. RS232 1 port (for PC communications and keyboard).) The Quick Wizard and no PoE support. Should have post event recording interval 30s (max 60s). Should have camera Alarm in(smart) motion detection, video loss, camera tamper intrusion, Multi loitering,crowd detection Resolution should be upto 3840x2160 and frame rate 30 fps Approved Make- Honeywell/Axis/Pelco.

Supply , installation, testing & commissioning of Surveliance 8 TB HDD. Make:- WD, Segate/DAICHI

Supply , installation, testing & commissioning of 55" IPS Ultra HD AI ThinQ TV Make: LG/Samsung/Panasonic

Supply, Installation,Testing & Commisioning of wireless mouse.

Supply, Installation,Testing & Commisioning of 5Mtr HDMI cable. Make : Hifocus

Supply, Installation,Testing & Commisioning of IP based PoE Phone with single lie Display with 2 Ethernet Port.Make: Grandstream/NEC/Mitel

Supply, Installation,Testing & Commisioning of IP PBX System support upto 1000Users and minimum 60 concurrent calls, integrated 2 PSTN trunk FXO ports through External Gateway, 2 analog telephone FXS ports with lifeline capability and up to 50 SIP trunk accounts, Gigabit network ports with Integrates PoE, USB, SD card, Supports up to a 5-level IVR (Interactive Voice Response), Supports any SIP video endpoint that uses the H.264, H.263 or H.263+ codecs.Make: Grandstream/NEC/Mitel

Supply, Installation,Testing & Commisioning of Dual band 802.11ax 2X2:2 WiFi6 Dual Band Access Point. Complying PoE+ for power, 6 Gbps aggregate wireless throughput, 2.5 Gbps RJ45, and 2.5 Gbps SFP wireline ports with inbuilt on premise virtual controller as well cloud based controlling and administration of WiFi systems. Make: Grandstream/NEC/Mitel

Supply, Installation,Testing & Commisioning of Grandstream Gate way Router with Built-in firewall provides 3years subscription for anti-virus, layer 3-7 IDS/IPS, DPI, SSL detection, and more. Built-in VPN router supports 2.5Gbps or 3Gbps to allow easy remote access. 2 x 2.5 Gigabit SFP port and 10 x Gigabit Ethernet ports *3x Fixed WAN. 2.5Gbps Router. 4 x PoE out ports, IEEE802.3af/at, Maximum PoE Wattage: 36W. Make: Grandstream/NEC/Mitel

Supply, Installation,Testing & Commisioning of 6F Single Mode Armoured FO Cable through existing conduit. Legrand/Tyco/Digisol/Commscope.

Supply, Installation,Testing & Commisioning of 6 Port Rack Mount Loaded LIU including SM SC Adaptor and Pigtail. Make: Legrand/Tyco/Digisol/Commscope.

Supply, Installation,Testing & Commisioning of 24 Port Rack Mount Loaded LIU including SM SC Adaptor and Pigtail. Make: Legrand/Tyco/Digisol/Commscope.

Supply, Installation,Testing & Commisioning of Single Mode SC-LC Type OFC Patch Cord, 2mtr length. Make: Legrand/Tyco/Digisol/Commscope.

Supply, Installation,Testing & Commisioning of 1000Base LX Fiber Transceiver. Make: Legrand/Tyco/Digisol/Commscope.

DOOR KEYCARD SWITCH

Supply,Installation,Testing& Commisioning of 15A key card switch with all acessories.Make:Legrand/Hikvision or equivalent.

Supply,Installation,Testing& Commisioning of key fob for key card switch with all acessories.Make:Legrand/Hikvision or equivalent.

HAND HELD METAL DETECTOR

SITC of Handheld Metal Detector : Low battery alarm Adjustable detection sensitivity for different requirements Power Supply: Standard 9 V (6F22) battery Frequency: 25 KHz LED for battery/Charging indication High detection speed with big probe area Temperature: -20 °C to 55 °C

PUBLIC ADDRESS SYSTEM

Supply of Digital Public Address and Emergency Sound System Controller complying to of EN-54 Certified IP based EVAC PA controller capable of adding 12 zones in the system and expandable upto 50 zones with full DSP functionality. 8 audio inputs, 4 audio outputs, 4 channel output matrix. Shall support amplifier redundany, 12 speaker line outputs. 5000 fault, warning and event conditions log. Built in message manager for 100 emergency/business calls up to 60 minutes. 12 control inputs and 12 control outputs. Impedance measurement and Pilot Tone supervision for speaker line monitoring. The controllers shall be able to exchange audio signals over the network without the need of a running PC/server. Multiple controllers can be networked over IP . audio up to 16 digital audio input signals and 16 digital audio output.Model no-PAVIRO PVA-4CR12,MAKE:osch/Bose/Axis

Supply of (1000 W Amplifier) The Digital 2x 500W Class D, high efficiency amplifier shall be an EN54-16 compliant and certified system device in a 2 RU, 19”cabinet.Model no-PAVIRO PVA-2P500,MAKE:Bosch/Bose/Axis

. The amplifier shall be permanently monitored by the system controller. A special standby mode shall be provided for saving energy during the time the amplifier is not is use with respect to all economical and supervision aspects.

• 2x 500 Watt Class D amplifier

• 4 channel input on RJ45 connector, amp link in and out (4 channel dynamic input channel switching for each amplifier

• Amplifier efficiency >= 78%

• Limiter prevents audible distortion Signal to noise ratio, A-weighted: >104 dB

Supply of 6W Cabinet LoudspeakerSound Pressure Level at 6W/1 W (1 kHz, 1 m) 96dB/88dB,Effective frequency range 150Hz to 15kHz,Opening angle horizontal(1kHz/ 4kHz,-6dB) 165°/95°,Opening angle vertical(1kHz/ 4kHz,-6dB) 160°/70°,Rated Impedance 1667 Ohm,Rated input voltage 100V,Connector 4 Pole Push In Terminal,Model no-LCZ-UM12-IN,MAKE:Bosch/Bose/EV

Supply of 2 Core Loudspeaker Cable for connectivity,MAKE:Krystal/Belden/Kltoz

Supply of 17U Equipment Rack ,MAKE:Netrack/Valrack

Installation , Testing & Commissioning of the system

DIGITAL CONFERENCE SYSTEM FOR CONFERENCE -1(1st floor)

Supply of 86", Android 14 , 8/128 GB, 40 Touch Point (32 Touch Points) , Speaker 74 W (Max) The display shall be an 86‑inch 4K UHD interactive panel featuring an IPS display with 400‑nit brightness, 3,000:1 contrast ratio, 10‑bit color depth, anti‑glare tempered glass, infrared touch with up to 40‑point multi‑touch, and wide OS compatibility including Android, Windows, macOS, Linux, and Chrome OS. It shall run Android 14 with Google EDLA certification, octa‑core CPU, 8 GB RAM, 128 GB storage, comprehensive AV and USB interfaces, Wi‑Fi 6, Bluetooth 5.2, integrated high‑power speakers, and support wireless screen sharing, whiteboarding, and device management software.Make:SONY / LG/ Samsung

Supply of OPS 80 Pin- CPU : 12th Gen Intel Core - i5 , RAM : 8GB , Storage : 256 GB, Windows 10 Preloaded Make:SONY / LG/ Samsung

Supply of Swivable Display Brackets / Display Cart Product Category: TV Cart Rank: Economy Material: Steel Surface Finish: Powder Coating Color: Fine Texture Black Dimensions: 1050x570x1785mm (41.3"x22.4"x70.3") Column Size(Main Column/Extension Column): 50x50X1.2x1465mm (2"x2"X0.047"x57.7") Fit Screen Size: 37"-100" VESA Compatible:200x200,300x200,400x200,300x300,400x300,400x400,600x400,800x400,800x600t Make:Lumi / Ergotron /Humanscale

Supply o 24" Touch Monitor Make:SONY / Samsung / LG

Supply of professional 4K PTZ camera featuring a 1/1.8″ SONY CMOS sensor with 8.29 MP effective pixels, 31X optical zoom (6.91–214.64 mm), and minimum illumination of 0.05 lux for high-clarity imaging in low-light environments. The camera shall support UHD and Full HD video outputs via HDMI, SDI, LAN (PoE), and USB 2.0, delivering resolutions up to 3840×2160 @ 60 fps, and support H.264/H.265/MJPEG compression. It shall provide wide pan/tilt movement (±110° pan, –30° to +30° tilt) with high-speed and precision control, support up to 255 presets, and include real-time auto-tracking and zone tracking modes. The unit shall support VISCA, Pelco-D/P, ONVIF, RTSP/RTMP, and network management with remote upgrade/reset. Audio shall be supported via 3.5 mm input with AAC compression and output over HDMI, LAN, and USB. The camera shall operate on DC 12V with PoE support, consume ≤12 W, be suitable for indoor professional conferencing, lecture capture, and broadcast applications, and include standard accessories with optional wall/ceiling mounts.

Supply of 8-Port True 4K HDMI Switch The HDMI switch shall have eight (8) HDMI input ports and one (1) HDMI output port, supporting HDMI 2.0 and HDCP 2.2 with resolutions up to 4K@60 Hz (4:4:4) and a maximum data rate of 18 Gbps. It shall support RS‑232 and IR control, include an auto‑switch DIP control, operate over HDMI cable lengths up to 5 m at 4K resolution, and function within 0°C to 40°C and 0–80% non‑condensing humidity, with low power consumption via a locking DC power connector.

Supply of The HDMI extender shall consist of a transmitter and receiver supporting HDMI input/output, IR control, and CAT5e/6 connectivity, with transmission capability up to 40 m at 4K@30 Hz and up to 70 m at 1080p. It shall support IR remote management, operate on 12 V DC power with a maximum consumption of 18 W, function within 0°C–40°C and 20–90% humidity, and be suitable for desktop mounting with a compact form factor.

Supply of True 4K HDMI Repeater with Audio Embedder and De-Embedder

Supply of Hydrallic Cable Cubby with HDMI, USB power and 2 x Universal Power Socket

Supply of Extraflat flat electret cardioid desktop microphone with internal preamplifier, phantom power (12–52 VDC), 30 Hz–12 kHz frequency response, -53 dB sensitivity, 100 Ω impedance, max SPL 125 dB, SNR 67 dB, ON/OFF switch, and 8 m Mini XLR to XLR cable; metal body, white finish.

Supply of Dual Channel Handheld Microphone

Supply of DSP system features 32-bit conversion,64x64 dante, 48kHz sampling, and 110dB dynamic range with ultra-low noise and distortion. It supports echo cancellation, phantom power, USB audio, Dante networking, and flexible control via RS-232, TCP/IP, and Web GUI. Designed for reliability, it operates efficiently with <60W power consumption and a compact, install-friendly design with Eachl of 7 Input, 1 output, AEC, 3 GPIO Cards Speaker & Amp, DSP are from the same OEM

Supply of Amplefier shall support IEEE 802.3at PoE+ Class 4 with a maximum power consumption of 30 W, providing four (4) powered output channels and an IEEE 802.3af PoE microphone port. It shall operate at 0°C–40°C with fanless convection cooling and support Dante™ audio networking with AES67 compliance and four (4) output channels. The unit shall feature a Class‑D amplifier with up to 15 W output, a 20 Hz–20 kHz ±1 dB frequency response, 48 kHz sampling, >90 dB dynamic range, and <0.3% distortion, and shall include RJ‑45 connectivity for LAN, microphone, and speakers with status and activity indicators.Speaker & Amp, DSP are from the same OEM

Supply of two‑way, 8‑ohm in‑ceiling loudspeaker rated at 30 W, featuring RJ‑45 Category‑cable audio input/output, fault sensing, and VoiceMatch support via Amp It shall operate at 0°C–40°C, provide wide 180° coverage, a 50 Hz–20 kHz frequency range, >91 dB sensitivity, and be housed in a steel backcan with a white powder‑coated grille,Speaker & Amp, DSP are from the same OEM

Supply of LED Illuminate-Metal Push Button Switch for Look at me feature

Control System - Control Box shall have 1 GB SDRAM, 8 GB flash memory, Gigabit Ethernet, USB Type‑A interface, programmable RS‑232/422/485, IR, relay, digital I/O, and 12 VDC output ports, with support for standard network protocols including TCP/IP, DHCP, HTTPS, and SSH. It shall include power on/off control, IR learning, reset functions, and operate with low power consumption under AC 110 V and 220 V supply.

Supply of USB 2.0 Cat 5 Extender

Supply of 1M High speed HDMI cable

Supply of 10" Andorid tab for controlling automation

Supply of 16 port PoE L2 Smart Managed / L3 network switch

Supply of Floor 15 U Rack for mounting devices with Accessories

Supply of Cables and Connectors for the solution

Installation and Commisioning of the above solutions, excludes cable laying, civil work, wooden work

DIGITAL CONFERENCE SYSTEM FOR CONFERENCE -2(9th floor)

Supply of 75‑inch 4K UHD interactive display panel with VA technology, 400‑nit typical brightness, 5,000:1 contrast ratio, 10‑bit color depth, wide 178° viewing angle, anti‑glare tempered glass, and infrared touch supporting up to 40‑point multi‑touch with high accuracy and ≤5 ms response time. It shall run Android 14 with Google EDLA certification, an octa‑core processor, 8 GB RAM, 128 GB storage, built‑in Wi‑Fi 6 and Bluetooth 5.2, integrated high‑power speakers, OPS expansion support, comprehensive AV and USB connectivity, and TÜV‑certified eye‑care features, suitable for collaboration, whiteboarding, and wireless screen sharing across major operating systems. OPS & Interactive Display should be from same OEM .Make:SONY / LG/ Samsung

Supply of OPS 80 Pin- CPU : 12th Gen Intel Core - i5 , RAM : 8GB , Storage : 256 GB, Min Windows 10 Preloaded Make:SONY/ LG/ Samsung

Supply of Swivable Display Brackets / Display Cart Product Category: TV Cart Rank: Economy Material: Steel Surface Finish: Powder Coating Color: Fine Texture Black Dimensions: 1050x570x1785mm (41.3"x22.4"x70.3") Column Size(Main Column/Extension Column): 50x50X1.2x1465mm (2"x2"X0.047"x57.7") Fit Screen Size: 37"-100" VESA Compatible:200x200,300x200,400x200,300x300,400x300,400x400,600x400,800x400,800x600t Make:Lumi / Ergotron /Humanscale

Supply o 24" Touch Monitor Make:SONY / Samsung / LG

Supply of 20x Optical Zoom PTZ Camera should be equipped with a 1/2.8” CMOS image sensor, offering a resolution of 1920x1080, and providing a minimum illumination of 0.5 Lux @ F1.8 (AGC ON). The camera should feature a focal length range of 5.2 to 98 mm with a 20x zoom, an F-number range of F1.5 to F3.0, and a field of view from 55.8° (wide) to 3.2° (tele). It must support video output through HDMI, USB 3.0, USB 2.0, and IP (RJ-45), with video compression using H.264. The device should support a maximum resolution of 1920x1080 @ 60fps for simultaneous output from IP , HDMI and USB 3.0. The camera should include image auto-adjustment features such as BLC, auto white balance, focus, aperture, WDR, and electronic shutter, along with adjustable image settings for SNR, brightness, color, saturation, contrast, sharpness, BW mode, and gamma curve. The pan/tilt rotation should cover -170° to +170° (pan) and -30° to +90° (tilt), with pan/tilt speed ranging from 0.1° to 60° per second (pan) and 0.1° to 30° per second (tilt), and a maximum pan speed of 60°/second and tilt speed of 30°/second. It should have a control port (RS-232) for tally light and support control protocols like VISCA, Pelco-D, and Pelco-P. The network interface must be 100 Mbps Ethernet, supporting RTSP, RTMP, and ONVIF protocols. The device should allow for up to 255 preset positions and be sourced from a country not sharing a land border with India. Both the camera and recording device should be from the same OEM.

Supply of HDMI extender shall consist of a transmitter and receiver supporting HDMI input/output, IR control, Loop Out and CAT5e/6 connectivity, with transmission capability up to 40 m at 4K@30 Hz and up to 70 m at 1080p. It shall support IR remote management, operate on 12 V DC power with a maximum consumption of 18 W, function within 0°C–40°C and 20–90% humidity, and be suitable for desktop mounting with a compact form factor.

Supply of Hydrallic Cable Cubby with HDMI, USB power and 2 x Universal Power Socket

Supply of boundary layer microphone should feature an electret transducer with cardioid (unidirectional) directionality, providing a sensitivity of -53 dB (±3 dB) and a frequency response range from 30 Hz to 12,000 Hz. The microphone should have an output impedance of 100 ohms, a maximum sound pressure level (SPL) of 125 dB at 1kHz with 1% total harmonic distortion (THD), and a signal-to-noise ratio of 67 dB. The device must include an ON/OFF signal switch, operate with a phantom power supply (12 to 52 VDC), and consume less than 6 mA. Constructed from durable metal, the microphone is designed for reliable performance in professional settings. The OEM must be from a country that does not share a land border with India.

Supply of DSP system features 32-bit conversion 48kHz sampling, and 110dB dynamic range with ultra-low noise and distortion. It supports echo cancellation, phantom power, USB audio, Dante networking, and flexible control via RS-232, TCP/IP, and Web GUI. Designed for reliability, it operates efficiently with <60W power consumption and a compact, install-friendly design with total of 7 Input, 2 output, AEC, 3 GPIO Cards.

Supply of Amplefier shall support IEEE 802.3at PoE+ Class 4 with a maximum power consumption of 30 W, providing four (4) powered output channels and an IEEE 802.3af PoE microphone port. It shall operate at 0°C–40°C with fanless convection cooling and support Dante™ audio networking with AES67 compliance and four (4) output channels. The unit shall feature a Class‑D amplifier with up to 15 W output, a 20 Hz–20 kHz ±1 dB frequency response, 48 kHz sampling, >90 dB dynamic range, and <0.3% distortion, and shall include RJ‑45 connectivity for LAN, microphone, and speakers with status and activity indicators.Speaker & Amp, DSP are from the same OEM .

Supply of two‑way, 8‑ohm in‑ceiling loudspeaker rated at 30 W, featuring RJ‑45 Category‑cable audio input/output, fault sensing, and VoiceMatch support via Amp It shall operate at 0°C–40°C, provide wide 180° coverage, a 50 Hz–20 kHz frequency range, >91 dB sensitivity, and be housed in a steel backcan with a white powder‑coated grille,Speaker & Amp, DSP are from the same OEM .

Supply of LED Illuminate-Metal Push Button Switch for Look at me feature

Control System - Control Box shall have 1 GB SDRAM, 8 GB flash memory, Gigabit Ethernet, USB Type‑A interface, programmable RS‑232/422/485, IR, relay, digital I/O, and 12 VDC output ports, with support for standard network protocols including TCP/IP, DHCP, HTTPS, and SSH. It shall include power on/off control, IR learning, reset functions, and operate with low power consumption under AC 110 V and 220 V supply.

Supply of USB 2.0 Cat 5 Extender

Supply of 1M High speed HDMI cable

Supply of 10" Andorid tab for controlling automation

Supply of 16 port PoE L2 Smart Managed / L3 network switch

Supply of Floor 15 U Rack for mounting devices with Accessories

Supply of Cables and Connectors for the solution

Installation and Commisioning of the above solutions, excludes cable laying, civil work, wooden work

External Kiosk panel(Ex. Panel-1)

Supply, installation, testing and commissioning of IP 65 cubicle type sectionalised, front operated bottom entry outdoor type Kiosk Panel Boards suitable for operation at 415V, 3 phase, 4 wire, 50Hz distribution system fabricated out of 2.0 mm thick CRCA sheet, insulated busbar with heat shrienkable PVC sleeve, base channel, complete with all accessories including interconnections, earth bus etc as required.MAKE:Schneider/SIEMENS/Legrand/LK.

Incomer cum Outgoing

One(1)415A, 800A 4P, 50KA, EDO Type ACB with (with Over current / Earth fault / Short circuit, Neutral Overload ) with Current Metering with display , Last 20 Trip History, Power METERING & CAPABLE FOR COMMUNICATION IN FUTURE shunt trip release,auxilliary contactor and terminals taken out suitable for termination of cable as required. One(1) - Multifunction meter (V,A,KWHr, KW, P, F), (1)set of – 800/5A , 15VA , CL 1.0. CTs One set - Indicating lamp for ON/OFF/Trip and Phase indication with control fuse/ MCB. One(1)- Trip Push Button MAKE:Legrand(DMX3),Siemens (3WA ),Schneider (Masterpact NW ),LK(U-POWER Omega )

PANEL AS ABOVE

Main LT Panel

S/I/T&Commissioning of LT indoor floor mounted(Totally type tesed standard) TTA IEC:61439-I &II cubical type electrical main panel (for both light and power circuit) made out by 2mm CRCA steel sheet duly derusted & painted by siemens gray powder cote paint is designed as G.A drawing as per direction of Engg.-in-Charge.Warrentee period of replacement of panel & accessories must be with compelete test certificate must be submitted along with panel board including component list.Make of main LT panel-Schneider(BLOCKSET)/SIEMENS(SEIPAN-8PU)/Legrand(XL3)/LK(Ti) 80X10MM Separate Aluminium Earth bus bar should be installed.Warrentee period of replacement of panel & accessories must be 1 years & compelete test certificate must be submitted along with panel board including component list.All the outgoing and incoming feeders shall have ON/OFF/TRIP indication.

One (1)- Incoming feeders from transformer

415V,800A, EDO TYPE ACB Micro Processer Based with Breaking capacity - Icu= Ics= Icw= 50kA for 1 sec having LSING Protection with Display-Current Metering with Last Trip Record Data. (Communication with On & Off Status indication for Remote Closing and Opening operation of breakers through Modbus RS485 protocol and uploading breaker status to Users Computer/SCADA.) & Electrical locking for normal & DG .(make-MAKE:Legrand(DMX3),Siemens (3WA ),Schneider (Masterpact NW ),LK(U-POWER Omega ) (WITH AXULARY FOR BMS) With On/Off/Trip Indication with TNC switch.

Electrical Interlocking System-415V,800A, EDO TYPE ACB

1 No PLC based Logic controller Comprising of

1 No - PLC based logic contrller for 2 nos of DG & 1 no of Transformer,EM DG with auto syncronisation, auto load sharing & energy monitoring system. Busbar-1000 Amp Al busbar with SC rating of 36 KA suitable for operation at 415 Volt, 50 Hz, 3 Phase supply .

One (1)- Incoming feeders from Synchronising Panel

415A, 800A , FP, 50kA Fixed type, Manual operated ACB with Microprocessor based releases (with Over current / Earth fault / Short circuit ) & Trip & close Coil with Under Voltage releases, high speed closing feature with earthing, door interlock, automatic safety shutters to shroud the bus bar side and FRP sheet barrier on the incoming & outgoing cable sides of the circuit breaker.MAKE:Legrand(DMX3),Siemens (3WL ),Schneider (Masterpact NW ),LK(U-POWER Omega )

Outgoing Feeder Consists of:

Two(2)-Outgoing feeders consist 01 nos for FF Pump & 01 nos spare each comparising of:

415A, 630A 4P MCCB with ROM Breaking capacity – 36KA with adjustable Micro Processer Based Release with Ics=100% Icu (LSI Protection) with 3 NosIndicating lamp for ON/OFF/Trip with control fuse/ MCB, 3 Nos 250/5 A 15VA Cl 1.0 CTs, 1No - Multifunction meter (V,A,KWHr, KW, P, F) ( Make-LEGRAND-DPX3 / Siemens-3VL Model/ Schneider- NSX/ LK D-shine)with shunt trip.with axulary).

Two(2)-Outgoing feeders consist 01 nos for VRF Panel & 01 nos spare each comparising of:

415A, 400A 4P MCCB with ROM Breaking capacity – 36KA with adjustable Micro Processer Based Release with Ics=100% Icu (LSI Protection) with 3 NosIndicating lamp for ON/OFF/Trip with control fuse/ MCB, 3 Nos 250/5 A 15VA Cl 1.0 CTs, 1No - Multifunction meter (V,A,KWHr, KW, P, F) ( Make-LEGRAND-DPX3 / Siemens-3VL Model/ Schneider- NSX/ LK D-shine)with shunt trip.with axulary).

One(1)-Outgoing feeders consist 01 nos for APFC Panel comparising of:

415A, 250A 4P MCCB with ROM Breaking capacity – 36KA with adjustable Micro Processer Based Release with Ics=100% Icu (LSI Protection) with 3 NosIndicating lamp for ON/OFF/Trip with control fuse/ MCB, 3 Nos 250/5 A 15VA Cl 1.0 CTs, 1No - Multifunction meter (V,A,KWHr, KW, P, F) ( Make-LEGRAND-DPX3 / Siemens-3VL Model/ Schneider- NSX/ LK D-shine)with shunt trip.with axulary).

Two(2)-Outgoing feeders consist 01 nos for (GND/1ST/2ND)Floor Panel & 01 nos spare each comparising of:

One (1)-160 Amp, 25 KA, 4P MCCB,with ROM with adjustable Thermal Magnetic Release with Ics=100% Icu with 3 NosIndicating lamp for ON/OFF/Trip with control fuse/ MCB, 3 Nos 160/5 A 15VA Cl 1.0 CTs, 1No - Multifunction meter (V,A,KWHr, KW, P, F)( Make-LEGRAND-DPX3 / Siemens-3VL Model/ Schneider- NSX/ LK D-shine)with shunt trip.with axulary).

Ten (10)- Outgoing feeders -01 nos for Hot water Panel,01 nos for Basement Ventelatar,01 nos for(3rd/4th) Floor Panel,01 nos for(5th/6th) Floor Panel,01 nos for(7th/8th) Floor Panel,01 nos for(9th/Terrace floor) Floor Panel,01 nos for Pressurisation Fan Panel ,01 nos for EV Charging Panel & 01 nos spare each comprising of

One (1)- 100 Amp 4P MCCB with ROM 25kA with adjustable Thermal Magnetic Release with Ics=100% Icu with 3 NosIndicating lamp for ON/OFF/Trip with control fuse/ MCB, 3 Nos 100/5 A 15VA Cl 1.0 CTs, 1No - Multifunction meter (V,A,KWHr, KW, P, F) ( Make-LEGRAND-DPX3 / Siemens-3VL Model/ Schneider- NSX/ LK D-shine)with shunt trip.with axulary).

Five(5) - Outgoing Feeder:01 nos for PH Panel, 03 nos for LIFT Supply&01 nos spare each Comprising of

One (1)- 63 Amp 4P MCCB with ROM 25kA with adjustable Thermal Magnetic Release with Ics=100% Icu with 3 NosIndicating lamp for ON/OFF/Trip with control fuse/ MCB, 3 Nos 63/5 A 15VA Cl 1.0 CTs, 1No - Multifunction meter (V,A,KWHr, KW, P, F) ( Make-LEGRAND-DPX3 / Siemens-3VL Model/ Schneider- NSX/ LK D-shine)with shunt trip.with axulary).

One(1) -Incoming Feeder for 01 nos Basements floor DB Supply each Outgoings are each Comprising of

Incoming:01 nos 63 Amp 4P MCCB with ROM 25kA with adjustable Thermal Magnetic Release with Ics=100% Icu with 3 NosIndicating lamp for ON/OFF/Trip with control fuse/ MCB, 3 Nos 63/5 A 15VA Cl 1.0 CTs, 1No - Multifunction meter (V,A,KWHr, KW, P, F) ( Make-LEGRAND-DPX3 / Siemens-3VL Model/ Schneider- NSX/ LK D-shine)with shunt trip.with axulary). with Outgoings: 04 nos 32A,DP,MCBs for Basement 1&2 Lighting DB & 02 nos spare.

PANEL AS ABOVE

VRF PANEL Supply, installation, testing and commissioning of cubicle type sectionalised, front operated top entry dust and vermin proof M.V.Panel Boards suitable for operation at 415V, 3 phase, 4 wire, 50Hz distribution system fabricated out of 2.0 mm thick CRCA sheet, insulated busbar with heat shrienkable PVC sleeve, base channel, complete with all accessories including interconnections, earth bus etc as required.MAKE:Schneider/SIEMENS/Legrand/LK.

Busbar -400 Amp Al busbar with SC rating of 36 KA suitable for operation at 415 Volt, 50 Hz, 3 Phase supply

One (1)- Incoming feeders consist for VRF Panel Incomer…

415A, 400A 4P MCCB with ROM Breaking capacity – 36KA with adjustable Micro Processer Based Release with Ics=100% Icu (LSI Protection) with 3 Nos Indicating lamp for ON/OFF/Trip with control fuse/ MCB, 3 Nos 250/5 A 15VA Cl 1.0 CTs, 1No - Multifunction meter (V,A,KWHr, KW, P, F)( Make-LEGRAND-DPX3 / Siemens-3VL Model/ Schneider- NSX/ LK D-shine)with shunt trip.with axulary).

Outgoing Feeders Consist of:

Ten(10)- Outgoing feeders comprising of

One (1)- 63A , 4P MCB 10kA,C series,415V . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/LK EXORA.

Ten(10)- Outgoing feeders comprising of

One (1)- 63 Amp , 4P RCCB,300MA,415V . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/LK EXORA.

PANEL AS ABOVE

APFC PANEL(100 KVAR)

Supply,installation, testing & commissioning of Auto Power Factor Correction Relay (APFCR-100KVAr) suitable for 415Volts 3Phase 4wiresystem, fabricated from 14/16SWG CRCA sheet steel, single fronted, free standing, front hinged, rear removable, extendable on both sides, dust & vermin proof, cubicle type, floor mounted, gland plates at top/bottom for control cables, complete with internal wiring, ferrules, name plates, painting etc., conforming to the technical specification for panels& comprising of the following. MakeMAKE:Schneider/SIEMENS/Legrand/LK.

ONE (1) Capacitor Panel (100 KVAr Capacitor)

Busbar - 250 Amp Al busbar with SC rating of 36 KA suitable for operation at 415 Volt, 50 Hz, 3 Phase supply

One(1) - Incoming feeder having

One (1) - 250 Amp, Moulded Case Circuit Breaker, 4P, Breaking capacity – 36 KA with ROM with adjustable Micro Processer Based Release with Ics=100% Icu (LSI Protection) with 3 NosIndicating lamp for ON/OFF/Trip with control fuse/ MCB, 3 Nos 250/5 A 15VA Cl 1.0 CTs, 1No - Multifunction meter (V,A,KWHr, KW, P, F)( Make-LEGRAND-DPX3 / Siemens-3VL Model/ Schneider- NSX/ LK D-shine)

One (1) Outgoing Feeders each provided with MCCB, Contactor, ON/OFF push button and indicating lamp and capacitors

One (1)-Outgoings each having

One (1) - 125A TP,25 KA,MCCB.

One (1) - Capacitor duty contactor suitable for 50 KVAr capacitor

One (1) - 50 kVAr, 440V, TP Heavy duty capacitor with internal wiring, fuses,Harmonic Filter (14%) etc. complete as required

One (1) copper wound dutuned Reactor for 50KVAr capacitor.

One (1)-Outgoings each having

One (1) - 63A, TP,10 KA,MCCB.

One (1) - Capacitor duty contactor suitable for 25 KVAr capacitor.

One (1) - 25 kVAr, 440V, heavy duty capacitor with internal wiring, fuses,Harmonic Filter (14%) etc. complete as required

One (1) copper wound dutuned Reactor for 25 KVAr capacitor.

Two (2)-Outgoings each having

One (1) - 25A, TP,10 KA,MCCB.

One (1) - Capacitor duty contactor suitable for 10 KVAr capacitor.

One (1) - 10 kVAr, 440V, heavy duty capacitor with internal wiring, fuses,Harmonic Filter (14%) etc. complete as required

One (1) copper wound dutuned Reactor for 10 KVAr capacitor.

One (1)-Outgoings each having

One (1) - 16A, TP,10 KA,MCCB.

One (1) - Capacitor duty contactor suitable for 5 KVAr capacitor.

One (1) - 5 kVAr, 440V, heavy duty capacitor with internal wiring, fuses,Harmonic Filter (14%) etc. complete as required

One (1) copper wound dutuned Reactor for 5 KVAr capacitor.

PANEL AS ABOVE

(G+FF+SF) FLOOR LIGHT & POWER PANEL

Supply,installation, testing & commissioning of testing & commissioning of FLOOR DISTRIBUTION PANEL suitable for 415Volts 3Phase 4wiresystem, fabricated from 14/16SWG CRCA sheet steel, single fronted, free standing, front hinged, rear removable, extendable on both sides, dust & vermin proof, cubicle type, floor mounted, undrilled gland plates at top/bottom, complete with internal wiring, ferrules, name plates, painting etc.

One (1) - 160 Amp 4P MCCB with ROM 16kA with adjustable Thermal Magnetic Release with Ics=100% Icu with 3 NosIndicating lamp for ON/OFF/Trip with control fuse/ MCB, 3 Nos 160/5 A 15VA Cl 1.0 CTs, 1No - Multifunction meter (V,A,KWHr, KW, P, F) ( Make-LEGRAND-DPX3 / Siemens-3VL Model/ Schneider- NSX/ LK D-shine)with shunt trip.with axulary).

Busbar - 160Amp,25KA Al busbar suitable for operation at 415 Volt, 50 Hz, 3 Phase supply

Five(5) - Outgoing Feeders for 1st Floor Distribution Panel,01 nos for UPS1 Incoming,01 nos for Façade lighting supply,01 nos for External feeder panel & 01 nos spare each consist of:

one (1)-63A , 4P MCB 10kA,C series,415V . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/LK EXORA.

Six(6) - Outgoing Feeders for 04 nos DBs,01 nos for UPS2 Incoming, & 1nos Spare consist of

One (1)-40A, 4P MCB 10kA,C series,415V . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/LK EXORA.

Three(3) - Outgoing Feeders for 02 nos DBs & 1nos Spare consist of

One (1)-32A, 2P MCB 10kA,C series,415V .Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/LK EXORA.

PANEL AS ABOVE

(3RD-4TH) FLOOR DISTRIBUTION PANEL

Supply,installation, testing & commissioning of testing & commissioning of FLOOR DISTRIBUTION PANEL suitable for 415Volts 3Phase 4wiresystem, fabricated from 14/16SWG CRCA sheet steel, single fronted, free standing, front hinged, rear removable, extendable on both sides, dust & vermin proof, cubicle type, floor mounted, undrilled gland plates at top/bottom, complete with internal wiring, ferrules, name plates, painting etc.

One (1) - 100 Amp, 16 KA, 4P MCCB,with ROM with adjustable Thermal Magnetic Release with Ics=100% Icu with 3 NosIndicating lamp for ON/OFF/Trip with control fuse/ MCB, 3 Nos 100/5 A 15VA Cl 1.0 CTs, 1No - Multifunction meter (V,A,KWHr, KW, P, F) ( Make-LEGRAND-DPX3 / Siemens-3VL Model/ Schneider- NSX/ LK D-shine)with shunt trip.with axulary).

Busbar - 100 Amp,25KA Al busbar suitable for operation at 415 Volt, 50 Hz, 3 Phase supply

Five(5) - Outgoing Feeders for 02 nos DBs & 01 nos spareeach consists of.

One (1)-40A , 4P MCB 10kA,C series,415V . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/LK EXORA.

Three(3) - Outgoing Feeders fo 02 nos DBs &01 nos Spare consist of

One (1)-32A, 2P MCB 10kA,C series,415V . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/LK EXORA.

PANEL AS ABOVE

(5TH-6TH) FLOOR DISTRIBUTION PANEL

Supply,installation, testing & commissioning of testing & commissioning of FLOOR DISTRIBUTION PANEL suitable for 415Volts 3Phase 4wiresystem, fabricated from 14/16SWG CRCA sheet steel, single fronted, free standing, front hinged, rear removable, extendable on both sides, dust & vermin proof, cubicle type, floor mounted, undrilled gland plates at top/bottom, complete with internal wiring, ferrules, name plates, painting etc.

One (1) - 100 Amp, 16 KA, 4P MCCB,with ROM with adjustable Thermal Magnetic Release with Ics=100% Icu with 3 NosIndicating lamp for ON/OFF/Trip with control fuse/ MCB, 3 Nos 100/5 A 15VA Cl 1.0 CTs, 1No - Multifunction meter (V,A,KWHr, KW, P, F) ( Make-LEGRAND-DPX3 / Siemens-3VL Model/ Schneider- NSX/ LK D-shine)with shunt trip.with axulary).

Busbar - 100 Amp,25KA Al busbar suitable for operation at 415 Volt, 50 Hz, 3 Phase supply

Five(5) - Outgoing Feeders for 02 nos DBs & 01 nos spareeach consists of.

One (1)-40A , 4P MCB 10kA,C series,415V . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/LK EXORA.

Three(3) - Outgoing Feeders fo 02 nos DBs &01 nos Spare consist of

One (1)-32A, 2P MCB 10kA,C series,415V . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/LK EXORA.

PANEL AS ABOVE

(7TH-8TH) FLOOR DISTRIBUTION PANEL

Supply,installation, testing & commissioning of testing & commissioning of FLOOR DISTRIBUTION PANEL suitable for 415Volts 3Phase 4wiresystem, fabricated from 14/16SWG CRCA sheet steel, single fronted, free standing, front hinged, rear removable, extendable on both sides, dust & vermin proof, cubicle type, floor mounted, undrilled gland plates at top/bottom, complete with internal wiring, ferrules, name plates, painting etc.

One (1) - 100 Amp, 16 KA, 4P MCCB,with ROM with adjustable Thermal Magnetic Release with Ics=100% Icu with 3 NosIndicating lamp for ON/OFF/Trip with control fuse/ MCB, 3 Nos 100/5 A 15VA Cl 1.0 CTs, 1No - Multifunction meter (V,A,KWHr, KW, P, F) ( Make-LEGRAND-DPX3 / Siemens-3VL Model/ Schneider- NSX/ LK D-shine)with shunt trip.with axulary).

Busbar - 100 Amp,25KA Al busbar suitable for operation at 415 Volt, 50 Hz, 3 Phase supply

Five(5) - Outgoing Feeders for 02 nos DBs & 01 nos spareeach consists of.

One (1)-40A , 4P MCB 10kA,C series,415V . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/LK EXORA.

Three(3) - Outgoing Feeders fo 02 nos DBs &01 nos Spare consist of

One (1)-32A, 2P MCB 10kA,C series,415V . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/LK EXORA.

PANEL AS ABOVE

(9TH & TERECE) FLOOR DISTRIBUTION PANEL

Supply,installation, testing & commissioning of testing & commissioning of FLOOR DISTRIBUTION PANEL suitable for 415Volts 3Phase 4wiresystem, fabricated from 14/16SWG CRCA sheet steel, single fronted, free standing, front hinged, rear removable, extendable on both sides, dust & vermin proof, cubicle type, floor mounted, undrilled gland plates at top/bottom, complete with internal wiring, ferrules, name plates, painting etc.

One (1) - 100 Amp, 16 KA, 4P MCCB,with ROM with adjustable Thermal Magnetic Release with Ics=100% Icu with 3 NosIndicating lamp for ON/OFF/Trip with control fuse/ MCB, 3 Nos 100/5 A 15VA Cl 1.0 CTs, 1No - Multifunction meter (V,A,KWHr, KW, P, F) ( Make-LEGRAND-DPX3 / Siemens-3VL Model/ Schneider- NSX/ LK D-shine)with shunt trip.with axulary).

Busbar - 100 Amp,25KA Al busbar suitable for operation at 415 Volt, 50 Hz, 3 Phase supply

Two(2) - Outgoing Feeders for 02 nos DBs & 01 nos spareeach consists of.

One (1)-63A , 4P MCB 10kA,C series,415V . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/LK EXORA.

Two(2) - Outgoing Feeders fo 02 nos DBs &01 nos Spare consist of

One (1)-32A, 2P MCB 10kA,C series,415V . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/LK EXORA.

One(1) - Outgoing Feeders fo 02 nos DBs &01 nos Spare consist of

One (1)-32A, 2P MCB 10kA,C series,415V . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/LK EXORA.

PANEL AS ABOVE

UPS Outgoing Panel

Supplying and fixing following way, DP, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCBOs/ISOLATORS).

One (1)-Incomer feeders consist of…

One (1) - 63A 4P MCCB with ROM 25kA with adjustable Micro processor Release with Ics=100% Icu. ( Make-LEGRAND-DPX3 / Siemens-3VL Model/ Schneider- NSX/ LK D-shine)with shunt trip.with axulary).

Threet(3) - Outgoing Feeder each comprising of

One (1) - 40A, 3P MCB 10kA,C series,415V . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/LK EXORA.

Ten(10) - Outgoing Feeder each comprising of

One (1) - 32A, 2P MCB 10kA,C series,415V . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/LK EXORA.

PANEL AS ABOVE

ELECTRICAL PANEL SUPPRESSION

Supply, fixing, testing and commissioning of 5 LB Clean Agent system complete with all necessary Clean Agent FK-5-1-12 / Novec 1230 (UL listed ) gas ,fitting ,support , and accessories, connected with PESO approved DLP valve with CE & PI marked, with PESO approved Cylinder, End of Line Adaptor,Pressure Switch (UL Listed) for monitor system activation .System shall be Helium Leak Tested to 10^-7 mbar l/s. (MAKE: SUPREMEX, SEVO, FIREBOY)

Supply, fixing, testing and commissioning of Flexible Polymer Detection Tube (size 6 mm outer dia & 4mm inner dia )with all necessary fittings &supports. (UL Listed) with all necessary fitting and support (MAKE: SUPREMEX, SEVO, FIREBOY)

Supply, fixing, testing and commissioning of Master control unit with audio visual alram with wiring to complete system operational control panel should have provision for integration with fire alram /scada/BMS system Health Monitoring Cum Alarm Panel (MAKE: SUPREMEX, SEVO, FIREBOY)

EXTERNAL LIGHTING PANEL 1

Supply, installation, testing and commissioning of cubicle type sectionalised, front operated bottom entry dust and vermin proof M.V.Panel Boards suitable for IP 54, operation at 415V, 3 phase, 4 wire, 50Hz distribution system fabricated out of 2.0 mm thick CRCA sheet, insulated busbar with heat shrienkable PVC sleeve, base channel, complete with all accessories including interconnections, earth bus etc as required. Make-L&T/Schneider/ABB/Legrand

Busbar -100A AL busbar with SC rating of 50KA suitable for operation at 415 Volt, 50 HZ , 3 phase Supply.

Incomer feeder consisting of

One (1)63 Amp,10kA,FP,MCB,C-CURVE

Four(4) - Outgoing Feeders each comprising of

One (1)40 Amp,10kAFP,MCB,C-CURVE

Six(6) - Outgoing Feeders each comprising of

One (1) 16 Amp,SP,MCB,C-CURVE

1 Nos - TIMER WITH CONTRACTOR

PANEL AS ABOVE

VTPN DB- UPS POWER SUPPLY FOR 3RD TO 9TH FLOOR

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

Incoming:

One (1)63 Amp,10kA,FP,MCB,C-CURVE

Outgoing:

09(Nine)-6-32A SP MCB(C-Curve)

PANEL AS ABOVE

Cable, Cable Tray,End Termination & Cable Jointing

Supplying & Testing of 1.1 KV grade Aluminium XLPE Armoured power cable of following size suitable for 415 Volt, 3Ph, 50 c/s supply Make-KEI/Finolex/Havells/Anchor/Gloster.

3.5C X 240 sqmm(TR - KIOSK,DG -LT PANEL )

3.5C X 150 sqmm(For VRF Panel)

3.5C X 120 sqmm

3.5C X 95 sqmm

3.5C X 50 sqmm(FOR EXTERNAL FEEDER PANEL)

4C X 16 sqmm

Supplying & Testing of 11/11 KV AL. CONDUCTOR/ XLPE INSULATED/ ROUND WIRE ARMOURED/ UNEARTHED GRADE POWER CABLE of following size suitable for 415 Volt, 3Ph, 50 c/s supply Make: KEI/Finolex/Havells/Anchor/Gloster.

3C X 120 sqmm(RMU TO TRANSFORMER)HT CABLE

Supplying & Testing of 1.1 KV grade Cu XLPE Un Armoured power cable of following size suitable for 415 Volt, 3Ph, 50 c/s supply. Make-KEI/Finolex/Havells/Anchor/Gloster.

3C X 2.5 sqmm(including termination)

4C X 6 sqmm(10kvaUPS cable,)

4C X 10 sqmm(lift,20kvaUPS cable)

Cable tray

Supply & installation of Hot -dip galvanized cable rack system made of 1.6 to 2mm thick sheet steel folded with two longitudinal side rails connected by rungs at regular intervals of following sizes with necessary Tee's, Vertical/ Horizontal Bends, expansion anchor fasteners, coupler plates, coupling fasteners, Grippler, GI thread rods of required height, including supply & grouting of supports as required at site. The supports should be painted with black enamel paint over a coat of anti corrosive primer. (Tray shall be measured along the central axis of the cable tray). Note: Cost of support shall be included (Distance between one support to other support mini. space 1.2mtr to 1.5 Mtrs gap as per site required). Make-BEC/MEM/ATUL/OBO.

300 mm (W) X 50 mm (Side Rail) with thickess 2 mm

600 mm (W) X 50 mm (Side Rail) with thickess 2 mm

Supply of exterior-rated architectural floor/wall/Pole mounted, IP66, round flood light complete with antiglare snoot. The power consumption should be not more than 80 watts, minimum system lumen delivered shall be 4840 lumens ±10%, 10° beam angle ±10%, CCT-RGNW K. LED from CREE/NICHIA/LUMILED/OSRAM. The housing material should be die-cast aluminum with Electrostatically applied polyester powder coating, The luminaire is to be installed with anti-aging and anti-UV high optical efficiency PMMA lenses and a clear tempered glass cover. Bracket shall have a locking mechanism to fix and secure the required tilting angle, ±90°. It should have CRI>80, and SDCM≤4. The driver should be integrated AC with PF>0.9 & and THD<20%. Leader cables, jumper cables, and IP68 connectors are included, minimum IK06. The operating temperature should be of -40°C to 50°C range and the storage temperature shall be -40°C to 70°C. the weight of luminaire shall be min 3kg. The lifetime of the luminaire (L70 @ Ta-35deg C) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self-declaration of ASTM B117 for 500 hours of salt spray test. Photometric data shall be passed on test results from an independent testing lab. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. All hardwired connections to LED fixture shall be reverse-polarity protected and shall provide high-voltage protection in the event that connections are reversed or shorted during installation. The luminaire should be BIS-certified. The luminaire manufacturer shall provide optical performance, polar diagram and photometric data in various formats including IES files in accordance with IES 79-08. This includes all the required hardware for the successful operation of the luminaire. All the technical parameters of the luminaire need approval from the lighting consultant. .Make:Philips/Wipro/Leksa/Reytek/Klite.

Supply of exterior rated architectural , IP66 3000K LED Flood Light with maximum System wattage of 120watt, min system lumen output of 7200lm ± 10%, 15-degree beam angle ± 10%, antiglare snoot, complete with integrated power supply, suitable IP66 connectors, . The connectivity should be of a daisy chain topology, allowing easy installation to form long run lengths. Lighting automation control equipment should be of the same company as of light fixtures. Fixture shall include Installation clamps, 5core/cat-6 or suitable control cables UV and weatherproof, other required accessories & hardware. The luminaire housing shall be die-cast Aluminium with Electrostatically applied polyester powder coating, silicon gasket and clear tempered glass, minimum dimension of Ø285mm X 225mm with bracket and minimum weight of 7kg. The Luminaire shall have tilting adjustability ± 90° for whole Luminaire. The LED luminaire shall have SDCM<4 for white, the life of Luminaire shall be 50000hrs L70B50 at 35deg C. The luminaire should be IP66 & IK-06, the luminaire should have successfully passed at 3G, ANSI C136.31 vibration test (The test should be conducted and passed at 3G as the luminaire are being installed on bridges). The operating temperature of Luminaire shall be -40°C to 50°C and storage shall be -40°C to 70°C.Luminaire should have corrosion resistance with self declaration of ASTM B117 for 500hrs of salt spray test. . Manufacturers self-declaration shall be uploaded along with the technical bid confirming to compliance of CE Declaration of Conformity, CQC declaration of conformity, RoHS compliance. Test reports for the aforesaid standards for the offered product or product from the same family with power rating in the range of (±10%) shall be uploaded along with technical bid. The bidder should also submit the BIS for proposed family of product. Make:Philips/Wipro/Leksa/Reytek/Klite.

Supply,Installation,Testing & Commissioning of exterior-rated architectural architectural3000 K LED linear luminaire with integrated driver of 1000 mm length having maximum wattage of 50W. Rated input supply of Input Voltage 220- 240 VAC.. LED Make : CREE / LUMINOUS / OSRAM / Lumen Maintenance 50,000 hrs L50 at 35°C.Luminaire luminous flux of minimum 2460 Lm (with all channels on). Luminaire Housing - Extruded aluminum with die-cast aluminum end caps , Finish - Electrostatically applied polyester powder coating , Color - Dark Grey (RAL7012) , Bracket - Cold-rolled steel , Adjustability -Tilting angle ±95° , Lenses -Anti-aging and anti-UV high optical efficiency PMMA lenses, Gasket - Silicon , Cover - Clear tempered glass. Luminaire weight should not be more than 2kgs. Luminaire must have inrush current of Max 60A/450μs (cold start 230Vac/50Hz measured at 50% Ipeak), THD<20%, The Luminaire should be capable of producing dynamic color changing light by DMX/ Ethernet. IP67 male/female connectors for DMX through wiring (DMX versions only) control. IP protection rating : IP66, impact resistance IK 06. The luminaire should have beam angle of 15°(±10% ). CRI>80, White SDCM<4. Dimension of the luminaire should not be more than 1000 mm x 105mm x 45mm (with bracket). The luminaire should have Operating Temperature: -40°C to +50°C, BIS Certified Mandatory. The fixtures proposed must have passed LM79& LM-80 Reports from a NABL accredited laboratory. Datasheet of the luminaire, photometry file of the luminaire, LM79 report, LM80 report, BIS certificate of the luminaire along with sample from NABL laboratory should be submitted during bid submission. Make:Philips/Wipro/Leksa/Reytek/Klite.

Supply of slim, flexible outdoor rated IP68 LED luminaire for uniform white light. The luminaire housing should be of extruded silicone material with frosted silicone lens. The input voltage should be 24V DC and total power consumption each run length of 5m should not be more than 12W/m. The luminaire should have Silicone enclosure with opaque sides and frosted lens delivering a consistent >110° light beam across the length of the LED strip and shining the light only where aimedbeam angle should be 110deg with system lumen output not less than 1100 lm/m for White light and efficacy not less than 80lm/w for 3000K. Luminaire color temperature should be 3000K and CRI>80. For Eliminating color difference between different luminaries it should have binning tolerance of maximum 5 SDCM steps .The operating temperature should range between minus 40degC to 50degC. The luminaire should withstand the mechanical impact with IK06 or more. The luminaire life should be more than 30000hours @ L70 at 35degC. Luminaire should comply the UL/cUL, CE, CQC certifications and must be BIS certified. Similar to Philips make Unilinear Flex 5m Module, IP 65, Warm White(In meter) with all accaesories. Make:Philips/Wipro/Leksa/Reytek/Klite.

320W 24V DC Power Supply- Third party item

4Cx6 Sq mm al Arm cable with 8SWG

3C x 2.5 sq.mm. cu flexible . Cable - Shielded

4C x 1.5 sq.mm. cu Cable - flexible

Sub distribution panel

IP-66 Junction Box - 150mm x 150mm with gell with suitable required connector

IP-66 Junction Box - 300mm x 300mm with gell with suitable required connector

Survo stabilizer for main Power DB

Accessories from Driver box and DB and Others electrical equipements

Installation

SITC of 20KW head pump(Comparising of 2nos 10.5kw heat pump) having hot water generater capacity of 500Lt/hr(working temp:15 to430C, maximum outlet water temprature:550C) complete with stainless steel(316L)tank of 2000Lt capacity,Circulation pump, Recirculation pump, 2 x 11Kw Electrical Heater ,inter connecting pipes(duly insulated) along with Electrical Panel with control for automatic operation of heat pumps and Electrical Heaters (in case of heat pumps being out of service)as required. MakeofCompressor:Bitzer/Danfoss. MakeofHeatPump:Kehems/Thermax/Bluebox/Jaquar. Circulation pump make should be OEM manufacturer Make:Grundfos /KSB/Xylem, Recirculation pump Make:Grundfos /KSB/Xylem.

SIGNAGE:

Backlit Reception Signage: Supplying and fixing Premium LED Backlit Signage featuring the text "JHARKHAND BHAWAN" in a sophisticated 3D profile as per approved design. The letters shall be precision-fabricated from 3 mm thick 304-grade Stainless Steel with a high-polish Titanium Gold PVD coating to achieve a mirror-finish aesthetic. Each letter shall have a depth (return) of 50 mm and be mounted on the wall using concealed spacers to create a 15-20 mm offset for the "halo" lighting effect.The hight of text shall eb 450-600 mm. The illumination shall be provided by high-efficiency, moisture-resistant LED strip modules (Warm White, 3000K) installed within the letter casing to project a soft, uniform glow onto the background surface. The entire system must include a branded concealed power driver (IP67 rated) and be integrated with the reception's electrical circuit. The rate shall be inclusive of SS fabrication, PVD coating, LED fitments, specialized installation labor and all necessary wiring as per the instructions of the Engineer-in-Charge.

3D LED Acrylic Signage: Supplying and fixing Premium 3D LED Signage featuring the text "JHARKHAND BHAWAN" as per the customized requirements. The letters shall be 900mm height and fabricated with a 3 mm thick high-grade acrylic face for uniform light diffusion, mounted on a heavy-duty Mild Steel (MS) box-frame support structure. The MS frame shall be treated with anti-corrosive primer and finished in a matte black automotive-grade paint to ensure structural stability for high-elevation or rooftop mounting. Internal illumination shall be provided by high-efficiency, waterproof LED modules (IP67 rated) to ensure consistent brightness and weather resistance. The rate shall be inclusive of all acrylic crafting, LED fitments, electrical drivers, wiring and specialized onsite installation. Steel supports and fabrication shall be measured and paid separately. All works as per the instructions of the Engineer-in-Charge.

Wayfinding Signage: Supplying and fixing Premium Durable Self-Adhesive Signage for doors and walls (Dining, Recepction, Toilets, Conference Rooms, etc.). The signage shall be fabricated from 2 mm thick high-grade brushed Aluminum or Brass-finish ACP (Aluminum Composite Panel) with a protective anti-fingerprint coating. The text and pictograms shall be precision laser-engraved or UV-printed in high-contrast black ink to ensure maximum legibility. Each unit shall feature a heavy-duty industrial-grade 3M self-adhesive backing for seamless, drill-free installation on glass, wood, or masonry surfaces. The rate includes design layout, substrate fabrication, adhesive application, and onsite installation.

Solid Brass Room Signage: Supplying and fixing Premium Architectural Brass Room Number Signage of approximate size 150 mm x 75 mm (6" x 3"), as per the approved design. The signage shall be fabricated from 3 mm thick solid brass plate, precision-cut and finished with a high-polish mirror effect. The room numbers and decorative side motifs shall be deep-etched and epoxy-filled in high-contrast black for permanent durability. Each plate shall be treated with a clear electrophoretic lacquer coating to prevent oxidation and maintain the gold-like luster over time. Installation shall be carried out using high-strength industrial-grade 3M adhesive backing or concealed brass studs for a seamless flush-mount finish on wooden doors or masonry walls. The rate shall be inclusive of material fabrication, etching, protective coating and onsite installation as per the instructions of the Engineer-in-Charge.

Sanitary Fixtures & Fittings

Providing and fixing white glazed vitreous china floor-mounted smart water closet European pattern of size 468W x 800D x 584H mm with S-Trap. The unit shall feature a sleek, one-piece skirted rimless bowl with CEFIONTECT dirt-repellent glaze and ultra-high-efficiency TORNADO FLUSH technology having a water use of 3.8L/3.0L for dual flush, operating at a required water pressure of 0.05 MPa (dynamic) to 0.75 MPa (static). The integrated solid seat cover system shall include advanced hygiene functions (EWATER+ self-cleaning wand and bowl sanitization system, PREMIST bowl surface wetting) and cleansing functions (AIR-IN WONDER-WAVE, rear, front, oscillating and pulsating cleansing, with water pressure control and wand position adjustment). Comfort functions shall include a sensor-activated auto open/close lid, intelligent auto flush with manual backup, temperature-controlled heated seat, a multi-temperature warm air dryer, an automatic active-carbon air deodorizer, an LED night light, and a programmable multi-user wireless remote control. The work includes supplying and installing the complete integrated toilet unit, requisite floor-mounting hardware, soil pipe seal/flange, and making all necessary plumbing and dedicated electrical connections. The rate shall be inclusive of all materials, labor, conveyance, testing for leakages and proper functioning, complete in all respects as per manufacturer's specifications and the direction of the Engineer-in-Charge. Make : TOTO NEOREST NX I (As per CS902VM#NW1, T53P100 of TOTO) In 9th floor room

Providing, fixing, testing, and commissioning a complete premium electronic wall-hung water closet system comprising a concealed flush tank with a robust steel mounting frame embedded within the wall, operated by a compatible dual-flush actuator platein black finish, coupled with a rimless, square-shaped vitreous china wall-hung WC pan featuring CEFIONTECT ion-barrier glazing and a high-efficiency 4.8/3L Tornado Flush system. The sanitary connection between the concealed cistern, the soil drainage system, and the ceramic pan shall be thoroughly secured using a watertight slip-in EPDM connector set. The installation is to be completed with an advanced electronic Urea Resin Washlet seat requiring an uninterrupted 220~240V power supply, featuring EWATER+ bowl sanitization, PREMIST technology, temperature-controlled heated seat and warm air dryer, auto deodorizer, automatic lid opening/closing mechanism, and a wireless remote control; the execution shall be inclusive of all necessary concealed plumbing hoses, electrical terminations, structural fasteners, and the application of anti-fungal silicone sealant at the wall junction, executed entirely as per the manufacturer’s technical specifications and the direction of the Engineer-in-Charge. Make: TOTO (Model: WH172AAT, CW522EMUNW1, TX215C, TCF804C2IN#NW1,MB175M#B (In suite room)

Providing and fixing a premium vitreous china one-piece floor-mounted Water Closet (European type) of TOTO make, complete with Tornado Flush and CEFIONTECT glaze technology, comprising the primary WC bowl (Model: C636DE#XW) with a 305mm rough-in, a matching soft-closing urea resin seat and cover (Model: TC281SJ), and all essential manufacturer-specific installation accessories including a PVC floor offset S-Trap connector (Model: TCP-16), a floor flange with P-seal gasket for leak-proof drainage (Model: T53P100), an internal water connection coupling (Model: HVM2L007Z), a chrome-plated brass angle stop valve with an integrated 300mm flexible hose (Model: HAP004A-F), and a 700mm flexible water supply hose (Model: HD4A104GVV), the work includes supplying and fixing all necessary installation hardware, brass screws, CP brass fasteners, and sanitary sealants, ensuring all joints are completely watertight and odor-proof, and making good the walls and floors wherever required, complete in all respects as per the manufacturer's standard installation guidelines and the direction of the Engineer-in-Charge. (In suite room & VIP Lounge)

Providing, fixing, testing, and commissioning a complete premium wall-hung water closet system comprising a heavy-duty concealed cistern with a structural steel mounting frame embedded within the wall, operated by a compatible dual-flush actuator plate, coupled with a white vitreous china wall-hung WC pan featuring CEFIONTECT ion-barrier glazing, a Rimless bowl design, and a high-efficiency Tornado Flush system. The sanitary connection between the concealed cistern, the soil drainage system, and the ceramic pan shall be securely executed using a watertight slip-in EPDM rubber connector set . The installation is to be completed with a non-electric Eco-Washer bidet seat and cover featuring a soft-closing mechanism and an integrated dual-nozzle water spray system (rear and front wash) operated by a side-mounted manual control knob, requiring a dedicated cold-water angle valve connection; the overall execution shall be inclusive of all necessary structural fasteners, internal plumbing hoses, jointing materials, and the application of an approved white anti-fungal silicone sealant at the wall-to-ceramic junction, leaving the installation entirely watertight and functional, executed strictly as per the manufacturer’s technical specifications and the direction of the Engineer-in-Charge. Make: (TOTO Model: WH132MHFR, CW542DMUNW1, TX215C, TCW09S) (In Deluxe room)

Providing and fixing a premium vitreous china two-piece (close-coupled) floor-mounted Water Closet (European type) of TOTO make, complete with Tornado Flush and CEFIONTECT glaze technology, comprising the primary WC bowl (Model: CW920K#XWH) with a 305mm S-Trap rough-in, a matching ceramic dual-flush cistern tank (Model: SW920K#WH), a soft-closing seat and cover (Model: TC281SJ), and a floor flange with P-seal gasket for leak-proof drainage (Model: T53P100), the work includes supplying and fixing all necessary installation hardware, brass screws, CP brass fasteners, internal tank flushing mechanisms, and sanitary sealants, ensuring all joints are completely watertight and odor-proof, and making good the walls and floors wherever required, complete in all respects as per the manufacturer's standard installation guidelines and the direction of the Engineer-in-Charge. (In Deluxe room)

Providing and fixing a premium vitreous china two-piece (close-coupled) floor-mounted Water Closet (European type) of TOTO make, comprising the primary elongated washdown WC bowl (Model: C320RE#W) with a 305mm S-Trap rough-in, a matching ceramic dual-flush water-saving cistern tank (Model: S320DPE#W) equipped with internal tank trims (4.8L/3L flush), a soft-closing polypropylene seat and cover (Model: TC385VS#W), and a floor flange with a seal gasket for leak-proof drainage (Model: T53P100), the work includes supplying and fixing all necessary installation hardware, brass screws, CP brass fasteners, internal tank flushing mechanisms, and sanitary sealants, ensuring all joints are completely watertight and odor-proof, and making good the walls and floors wherever required, complete in all respects as per the manufacturer's standard installation guidelines and the direction of the Engineer-in-Charge. (In common toilets)

Providing and fixing a complete premium vitreous china wall-hung Water Closet (European type) system of TOTO make, comprising a heavy-duty concealed flushing cistern with a pre-assembled powder-coated steel mounting frame (Model: WH131MHFR), a primary wall-mounted WC bowl in white finish (Model: CW554MUNW1), a matching soft-closing seat and cover (Model: TC613IN), a slip-in connector for secure plumbing and drainage integration (Model: TX215C), and a dual-flush actuator push panel in white finish (Model: MB174P#WH), the work includes supplying and fixing all necessary installation hardware, internal tank trims, CP brass fasteners, chair brackets, and sanitary sealants, ensuring all joints are completely watertight and odor-proof, securely anchoring the concealed frame to the floor and wall structure, and making good the walls and floors wherever required, complete in all respects as per the manufacturer's standard installation guidelines and the direction of the Engineer-in-Charge. (In common toilets)

Providing all materials, labour, T&P for fitting and fixing of white glazed vitreous china water closet (European pattern) 'P' or 'S' type with cistern & seat cover, wash hand basin of size 650mmx350mm with one pair basin bolt, one no. vertical swing grab bar & 4 nos. grab bars 692 mm long including supply of sutaible PVC wall plug and Brass screws etc. suitable for handicapped toilets in ground floor etc. all complete including cost and conveyance as per specification all complete as per direction of Engineer-in-charge. Make: As per Hindware : 70002

Providing, fixing, testing, and commissioning a premium fine fire clay (FFC) table-top washbasin. The basin shall feature an elegant, art-inspired zoomorphic design in a brilliant white finish, protected by a smooth, anti-bacterial ceramic glaze, with overall dimensions of 690(W) x 480(D) x 135(H) mm. It shall include a pre-punched 35 mm diameter single tap hole to accommodate a deck-mounted basin mixer and a standard 45 mm diameter waste outlet with bright gold PVD Bottle Trap 32mm Size with 300mm & 190mm Long Wall Connection Pipes & Wall flange. The execution shall be entirely inclusive of accurately positioning the basin over the prepared vanity counter, providing and securely fixing a compatible heavy-duty brass waste coupling, making perfectly watertight drainage connections to the bottle trap, and applying a continuous, neat bead of approved white anti-fungal silicone sealant along the basin-to-counter interface to prevent water seepage, all executed strictly in accordance with the manufacturer’s technical specifications and the direction of the Engineer-in-Charge. Model as per Artize Tailwater Collection (Model: TWS-WHT-75931N,ALA-GBP-509769L300x190) (In 9th floor room)

Providing, fixing, testing, and commissioning a premium vitreous china table-top washbasin . The basin shall feature the collection's signature art-inspired, jewelry-like sculptural design with echoing ovals in a brilliant white finish, protected by a smooth, anti-bacterial ceramic glaze, with overall dimensions of 725(W) x 480(D) x 150(H) mm. It shall include a pre-punched 35 mm diameter single tap hole to accommodate a deck-mounted basin mixer and a standard 45 mm diameter vertical waste outlet with bright gold PVD Bottle Trap 32mm Size with 300mm & 190mm Long Wall Connection Pipes & Wall flange. The execution shall be entirely inclusive of accurately positioning and leveling the basin over the prepared vanity counter, providing and securely fixing a compatible heavy-duty brass waste coupling, making perfectly watertight drainage connections to the bottle trap, and applying a continuous, neat bead of approved white anti-fungal silicone sealant along the basin-to-counter interface to prevent water seepage, all executed strictly in accordance with the manufacturer’s technical specifications and the direction of the Engineer-in-Charge. (Model:Artize Signature Collection (Model: TIS-WHT-73931N, Tiaara range,ALA-GBP-509769L300x190) (In 9th floor room)

Providing, fixing, testing, and commissioning a premium vitreous china table-top/console washbasin. The basin shall feature a sleek, modern, rounded-rectangular vessel design in a brilliant white finish, protected by CEFIONTECT ultra-smooth, ion-barrier ceramic glaze to prevent particulate adhesion and ensure enduring cleanliness, with overall visible dimensions of 500(W) x 380(D) x 70(H) mm with P-Trap in black finish. Designed as a freestanding counter-top basin without a pre-punched tap hole, it shall include an integrated overflow and a standard vertical waste outlet, intended to be paired with an extended-body (tall-boy) or concealed wall-mounted basin mixer. The execution shall be entirely inclusive of accurately positioning and leveling the basin over the prepared vanity counter, providing and securely fixing a compatible heavy-duty brass waste coupling, making perfectly watertight drainage connections to an approved bottle trap, and applying a continuous, neat bead of high-quality white anti-fungal silicone sealant along the basin-to-counter interface to ensure a rigid and leak-proof installation, all executed strictly in accordance with the manufacturer’s technical specifications and the direction of the Engineer-in-Charge. (TOTO Model: L5715E#XW, LF Series,THX1A-5N#MB). (In VIP Suits)

Providing and fixing a premium vitreous china console table-top wash basin of in white finish, measuring approximately 584mm (W) x 384mm (D) x 100mm (H) with a modern rectangular board-style design, the work includes supplying and fixing the ceramic basin onto the designated vanity counter, including the provision of all essential installation hardware, anchoring brackets (if applicable), standard 32mm CP brass waste coupling, and the application of anti-fungal sanitary silicone sealant along the resting edges to ensure a precise, completely watertight integration, making good the counter surface wherever required, complete in all respects as per the manufacturer's standard installation guidelines and the direction of the Engineer-in-Charge. TOTO make (Model: LW643JW/F#W) (In Deluxe room)

Providing, fixing, testing, and commissioning a premium fine fire clay (FFC) table-top washbasin. The basin shall feature the collection's signature zen-inspired, biomorphic vessel design in a brilliant white finish, protected by a smooth, anti-bacterial ceramic glaze with overall Size of 650x450x200 mm. Designed as a freestanding counter-top vessel, it shall feature a standard 45 mm diameter vertical waste outlet and is intended to be paired with an extended-body (tall-boy) or wall-mounted basin mixer. The execution shall be entirely inclusive of accurately positioning and leveling the basin over the prepared vanity counter, providing and securely fixing a compatible heavy-duty brass waste coupling, making perfectly watertight drainage connections to an approved bottle trap, and applying a continuous, neat bead of high-quality white anti-fungal silicone sealant along the basin-to-counter interface to ensure a rigid and leak-proof installation, all executed strictly in accordance with the manufacturer’s technical specifications and the direction of the Engineer-in-Charge. Artize Signature Collection (Model: CFS-WHT-69901N, Confluence range) (In common rooms)

Providing, fixing, testing, and commissioning a premium white vitreous china wall-hung urinal The urinal shall feature a sleek, compact design with integrated privacy shields and operate on an ultra-high-efficiency flush volume of just 0.5 liters per flush, with overall dimensions of 260(W) x 345(D) x 675(H) mm. Designed specifically with a top water inlet, it is intended to be paired with a compatible exposed manual or automatic sensor-operated urinal flush valve, operating within a required dynamic water pressure range of 0.25 MPa to 0.75 MPa. The execution shall be entirely inclusive of accurately positioning and securely mounting the fixture to the finished wall using the manufacturer-supplied heavy-duty wall brackets and flange, providing and securely connecting the top inlet spud to the flush pipe, and making perfectly watertight drainage connections to the sanitary waste line, along with applying a continuous, neat bead of approved white anti-fungal silicone sealant along the ceramic-to-wall interface to ensure a rigid, hygienic, and leak-proof installation, all executed strictly in accordance with the manufacturer’s technical specifications and the direction of the Engineer-in-Charge. (TOTO Model: UW904M#NW1).

Providing, fixing, testing, and commissioning a premium prefabricated luxury square steam shower cabin from the Artize Collection (Model: QUADRO-STEAM-CABIN-120X120) with Brown finish. The cabin, measuring exactly 1200(W) x 1200(D) x 2150(H) mm, shall be constructed using 8mm thick premium clear toughened safety glass panels enclosed within heavy-duty, corrosion-resistant metallic profiles in a polished finish. The system shall be fully integrated with a high-performance, rapid-heating steam generator (approx. 4.5kW - 6.0kW) featuring an automatic water flush/drain mechanism and an aromatherapy dispenser, operated via a sophisticated digital touch-screen control panel. The internal showering suite shall comprise an anti-scald thermostatic mixer valve with a multi-way diverter distributing water to a large ceiling-mounted overhead rain shower, a series of strategically placed high-pressure body massage jets, and a sleek hand shower on a flexible hose. Furthermore, the cabin must include integrated Chromotherapy RGB LED lighting, an exhaust circulation fan, a built-in seating arrangement, and a waterproof audio system (Bluetooth/FM connectivity). The execution shall be entirely inclusive of assembling the complete unit over the finished floor or matching shower tray, making perfectly watertight hot and cold water inlet connections (requiring 3 to 5 Bar dynamic pressure), executing a leak-proof drainage connection to the floor trap, and terminating the heavy-duty electrical connections (220-240V, single-phase) through a dedicated GFCI/RCBO breaker, finalizing the installation with the application of approved clear anti-fungal silicone sealant at all structural and floor joints, all executed strictly in accordance with the manufacturer’s technical specifications, electrical safety standards, and the direction of the Engineer-in-Charge. (Model as per Artize ASG-BRN-QUADRO120X100) (In 9th floor room)

Providing, fixing, testing, and commissioning a premium multi-outlet concealed thermostatic shower system from the Artize Collection, finished entirely in a highly durable, corrosion-resistant Gold Bright PVD (GBP). The system comprises a Thermatik-R concealed thermostatic mixing valve with an integrated 5-way control unit (THK-GBP-687N) to provide precise, anti-scald temperature regulation across all bathing zones. The primary showering suite features a 1000x750 mm AISI 304 stainless steel Rainjoy overhead shower (OSA-GBP-70015) equipped with multi-flow functions and integrated RGB LED Chromotherapy (requiring a safely isolated 12V SMPS and controller, connected to a 100-240V AC supply). The bathing experience is further enhanced by an array of 4 nos flush-mounted 120x30 mm concealed body shower jets (BSA-GBP-70075) to utilize the 5-way diverter's high-flow capacity, alongside a Navia 95mm single-function round hand shower (NAV-GBP-515537) connected via a matching Gold Bright PVD flexible braided hose and wall-integrated bracket & a bath spout (SPT-GBP-515463). The execution is entirely inclusive of all masonry chasing, anchoring the heavy-duty concealed brass valve bodies within the wall, safely terminating the electrical supply for the shower lighting, executing leak-proof hot/cold water and 5-way outlet plumbing connections, hydro-testing the pipeline grid for leaks before plastering, and securely mounting all exposed Gold Bright PVD trims over finished walls using clear anti-fungal silicone sealant, all executed strictly in accordance with the manufacturer's technical specifications and the direction of the Engineer-in-Charge. (In 9th floor room)

Providing, fixing, testing, and commissioning a 5-outlet concealed thermostatic shower system (TOTO G-Series) finished in black finish. The assembly comprises a 5-way thermostatic diverter trim (TBV11150A#MBL) with its concealed heavy-duty brass valve unit (TBN11HC0A), a 400x220mm overhead rain shower (TBW15AB0A#MBL, TBN01002B), a hand shower (TBW15CE0A#MBL) with an integrated wall supply elbow/bracket, side bar (BW160N0A#MBL,TBW160V0A#MBL), four Gyrostream body massage jets (TBW08008A#MBL), and a wall-mounted bath spout (TBG02001B#MBL). The rate is inclusive of all masonry chasing, anchoring concealed bodies, executing leak-proof hot/cold water and 5-way outlet plumbing connections, hydro-testing the pipeline grid (0.05 to 1.0 MPa), and securely mounting all exposed PFG trims over finished walls with anti-fungal silicone sealant, complete as per manufacturer specifications and the direction of the Engineer-in-Charge. (In VIP Suits)

Providing, fixing, testing, and commissioning a premium concealed thermostatic shower and bath system from the Artize Collection, finished entirely in a durable, multi-layer Chrome plating (CHR). The assembly comprises a Thermatik-R concealed thermostatic mixing valve with an integrated multi-way diverter trim and heavy-duty brass concealed body (Model: THK-CHR-693N) to ensure precise, anti-scald temperature control across the bathing zones. The showering setup features a high-performance overhead rain shower of size 370 x 250mm AISI 304 stainless steel (Model: OSA-CHR-70001SH) and is complemented by a sleek, contemporary wall-mounted bath spout (Model: SPT-CHR-41429). The rate is inclusive of all masonry chasing, anchoring concealed valve bodies within the wall depth, executing leak-proof hot/cold water inlet and appropriately routed outlet plumbing connections, hydro-testing the pipeline grid for leaks before plastering, and securely mounting all exposed Chrome trims and flanges over finished walls with clear anti-fungal silicone sealant, complete as per the manufacturer's technical specifications and the direction of the Engineer-in-Charge. (In deluxe rooms)

Providing, fixing, testing, and commissioning a premium single-lever basin mixer from the Artize Signature Collection (Model: TWR-GBP-75011B, Tailwater range). The fixture shall feature a zoomorphic, abstract design where the 'tail' acts as the mixer lever, moving backwards to open water flow and sideways for precise hot and cold temperature regulation. The solid brass body shall be finished in a highly durable, scratch-resistant Gold Bright PVD coating and is to be supplied without a pop-up waste system. The execution shall be entirely inclusive of supplying and securely connecting the integrated 450 mm long high-pressure flexible braided hoses to the hot and cold angle valves, along with all necessary heavy-duty brass fastening studs, EPDM rubber base gaskets, and watertight sealing materials to ensure a rigid, leak-proof installation on the washbasin or vanity counter, executed strictly in accordance with the manufacturer’s technical specifications and the direction of the Engineer-in-Charge.

Providing, fixing, testing, and commissioning a premium single-lever basin mixer from the Artize Signature Collection (Model: TIA-GBP-73011B, Tiaara range). The fixture shall feature its signature jewelry-inspired design with a unique, concentric oval/ring-shaped handle that pivots seamlessly to control both water flow and temperature. The solid brass body shall be finished in a highly durable, scratch-resistant Gold Bright PVD coating and is to be supplied without a pop-up waste system. The execution shall be entirely inclusive of supplying and securely connecting the integrated high-pressure flexible braided hoses to the hot and cold water angle valves, along with all necessary heavy-duty brass fastening studs, EPDM rubber base gaskets, and watertight sealing materials to ensure a rigid, leak-proof installation on the washbasin or vanity counter, executed strictly in accordance with the manufacturer’s technical specifications and the direction of the Engineer-in-Charge.

Providing, fixing, testing, and commissioning a premium tall single-lever basin mixer. The fixture shall feature a unique biomorphic, half-cut bamboo-inspired design that delivers a serene, natural waterfall flow into the palms with black matt finish. The solid brass body shall be finished in a highly durable, multi-layer Chrome plating and is to be supplied without a pop-up waste system. The execution shall be entirely inclusive of supplying and securely connecting the integrated 600 mm long high-pressure flexible braided hoses to the hot and cold water angle valves, along with all necessary heavy-duty brass fastening studs, an NSF-61 approved high-endurance ceramic cartridge, EPDM rubber base gaskets, and watertight sealing materials to ensure a rigid, leak-proof installation on the washbasin or vanity counter, executed strictly in accordance with the manufacturer’s technical specifications and the direction of the Engineer-in-Charge. (Model: Artize Signature Collection (Model:CNF-BLM-69009B, Confluence range)

Providing and fixing a premium luxury High Neck (Tall Boy) Basin Mixer featuring a chrome-plated solid brass body with single-lever operation and a sleek minimalist design, equipped with an advanced ceramic cartridge and integrated 450mm long flexible braided connection hoses, the work includes supplying and fixing the faucet onto the designated counter or basin platform (designed without a popup waste system), including the provision of all essential installation hardware, brass fasteners, and securing nuts, ensuring completely watertight and leak-proof connections to the angle stop valves, and making good the counter surface wherever required, complete in all respects as per the manufacturer's standard installation guidelines and the direction of the Engineer-in-Charge. (Artize make (Model: NAV-CHR-515009B) from the Navia collection)

Providing and fixing a premium luxury Extended Basin Mixer (Tall Boy) of featuring a chrome-plated solid brass body with distinctive Art Deco-inspired tapered angles and geometric curves, equipped with an advanced joystick single-lever control mechanism, an internal ceramic cartridge with a metal spindle, and integrated extended flexible braided connection hoses (designed without a pop-up waste system), the work includes supplying and fixing the extended faucet onto the designated counter or high-rim basin platform, including the provision of all essential installation hardware, brass fasteners, and securing nuts, ensuring completely watertight and leak-proof connections to the angle stop valves, and making good the counter surface wherever required, complete in all respects as per the manufacturer's standard installation guidelines and the direction of the Engineer-in-Charge. (Artize make (Model: LEX-CHR-67023B) from the Lexa collection)

Providing and fixing wall-mounted Vanity Base Cabinet of approved shade and finish of dimension 780 x 480 x 450 mm manufactured from high-grade water-resistant material (WPC/MR Grade) suitable for high-moisture environments, having overall dimensions compatible with integrated bowl basins, including all necessary high-quality stainless steel (SS 304) soft-close hinges, designer handles, and mounting hardware; the unit shall be installed perfectly leveled on wall-fasteners as per manufacturer’s design, ensuring all joints are sealed with mildew-resistant silicone sealant and integrated seamlessly with the plumbing inlet/outlet lines, complete as per the direction of the Engineer-in-Charge, including the cost of all materials, labor, and finishing etc complete. (As per Parryware (Product Code: C889K46) or equivalent

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink with drain board

510x1040 mm bowl depth 250 mm

Providing and fixing 8 mm dia botton type health faucet with flexible tube upto 1 metre long with wall hook of quality and make as approved by Engineer - in - charge. (As per K-97258IN-CP of Kohler or equivalent)

Providing and fixing 8 mm dia botton type health faucet in french gold with flexible tube upto 1 metre long with wall hook of quality and make as approved by Engineer - in - charge. (As per Kohler K-97258IN-ZZ-AF or eqv)

Providing and fixing 8 mm dia botton type health faucet in black matt finish with flexible tube upto 1 metre long with wall hook of quality and make as approved by Engineer - in - charge. (As per Kohler K-97258IN-ZZ-BL or eqv)

Providing and fixing CP Brass 32 mm size P Trap of approved quality & make and as per the direction of Engineer-in-charge.(As per TOTO THX1A-3N or eqv)

Providing and fixing 32 mm size french gold finish P Trap of approved quality & make and as per the direction of Engineer-in-charge.(As per TOTO THX1A-5N#MB or eqv)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Semi rigid pipe

40 mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600mm x 700mm column lighted mirror of superior glass (of approved quality) of approved make with fixing with clamp and nuts as required. Make : KOHLER. (As per K-35628IN-NA of Kohler or equivalent) (In VIP Suits)

Providing and fixing 762mm x 1016mm column lighted mirror of superior glass (of approved quality) of approved make with fixing with clamp and nuts as required. Make : KOHLER. (As per K-22928IN-NA of Kohler or equivalent) (In VIP Suits)

Providing and fixing 1016mm perimeter lighted mirror of superior glass (of approved quality) of approved make with fixing with clamp and nuts as required. Make : KOHLER. (As per K-35628IN-NA of Kohler or equivalent) (In 9th floor rooms)

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing toilet paper holder with flap : C.P. brass (Artize AVC-CHR-503753)

Toilet paper holder French Gold finish (As per Artize AVC-GBP-503753)

Toilet paper holder matt black finish (As per Artize AVC-BLM-503753)

15mm dia Angular Stop Cock with wall flange (As per Artize AUR-CHR-519053 or eqv)

15mm dia Angular Stop Cock with wall flange French Gold finish (As per Artize AUR-GBP-519053 or eqv)

15mm dia Angular Stop Cock with wall flange matt black (As per Artize AUR-BLM-519053 or eqv)

Two way Bib cock with Wall Flange (As per K-16094IN-4-CP of Kohler or eqv)

Two way Bib cock with Wall Flange french gold finish (As per K-16094IN-4-AF of Kohler or eqv)

Stop valve (SIG-CHR-41089 of Artize)

Stop valve (SIG-BLM-41089 of Artize)

Stop valve (SIG-GBP-41089 of Artize)

CP soap dish holder (As per QUA-CHR-61731 of Artize or Equivalent)

CP soap dish holder gold finish (As per QUA-GBP-61731 of Artize or Equivalent)

CP soap dish holder in matt black (As per QUA-BLM-61731 of Artize or Equivalent)

Towel Ring Round (As Per AVC-CHR-503721 of Artize or equivalent)

Towel Ring Round french gold finish (As Per AVC-GBP-503721 of Artize or equivalent)

Towel Ring Round matt black (As Per AVC-BLM-503721 of Artize or equivalent)

150mmX150mm SS square anti cockroach trap (K-7275IN-ZZ-CP)

150mmX150mm SS square anti cockroach trap in french gold (K-7275IN-ZZ-AF)

150mmX150mm SS square anti cockroach trap in matt black (K-7275IN-ZZ-Bl of Kohler)

Double Coat Hook (As per QUA-CHR-61761 of Artize or eqv)

Double Coat Hook french gold (As per QUA-GBP-61761 of Artize or eqv)

Double Coat Hook matt black (As per QUA-GBP-61761 of Artize or eqv)

Towel RACK 600mm Long with Lower Hangers, Stainless Steel (As per AVC-CHR-503781 of Artize or eqv)

Towel RACK 600mm Long with Lower Hangers, PVD gold finish (As per AVC-GBP-503781 of Artize or eqv)

Towel bar 600mm Long with Lower Hangers,Matt black (As per AVC-BLM-503781 of Artize or eqv)

Single Lever Sink Mixer With Swinging Spout on Upper Side (Wall Mounted Model) With Connecting Legs & Wall Flanges (As per K-29308IN-4-CP of Kohler or eqv)

High Speed Hand Dryer (Wall Embedded Type) 245W x 154D x 226H mm (As per TYC322WF of TOTO or eqv)

Glass Shower Partition upto 1200mm length, height 2000mm & thickness 8mm to 10mm with hardware having gold finish with 5 years of warranty (As per JSE-GLD-ALP110F1200H20FL of Jaquar)

Glass Shower Partition upto 1200mm length , height 2000mm & thickness 8mm to 10mm with hardware having matt black finish with 5 years of warranty (As per JSE-BLM-ALP110F1200H20FL of Jaquar)

Glass Shower Partition upto 1200mm length, height 2000mm & thickness 8mm to 10mm with hardware having chrome finish with 5 years of warranty (As per JSE-CHR-S810S0680H20X of Jaquar)

Providing & fixing Toilet Cubicle (of following standard dimension which includes 600mm door size width) made of heat, bacteria, water, chemical, scratch, impact and anti bacterial, anti virus, anti fungal resistant 12mm thick solid compact laminate panels. Finish of the compact laminate should be Suede / *Raw Silk, which includs doors, pilasters & intermediate panels finished with approved texture/shade as per the detail drawings & as per IS 2046 (Indian Standard) and as per fire retardant BS-476/97 standard. The product should have Green Guard Certificate. Reduction of virus in 2 hours and 24 hours when tested by ISO 21702: 2019 standard. This also includes providing and fixing in position necessary hardware made out of Stainless steel (Grade 316) & Aluminium powder coated top rail as per manufacturer’s specifications & Architects instructions like (1) SS Door Knob, (2) SS Gravity hinges, (3) SS Thumb turn lockset indicators, (4) Aluminum Powder Coated Top Rail, (5) SS Coat Hooks, (6) SS U-Channels, (7) SS Adjustable Foot, (8) Noise Deafening Tape etc. (9) Screws & wall Plugs. The top fitting should consist of Aluminium Powder Coated top rail which will get fixed with Mid & End pilasters. All other hardware & screws will of stainless steel in 304 Grade with satin finish. Top rail is extruded Aluminium will be powder coated or anodized (Grade 6063 Micron Aluminium). All pilasters are supported by stainless steel adjustable footing with non corrosive steel inserts. Toilet Cubicle with standard dimension of as per drawing, which includes 600mm door size width). (Make: Greenlam/Merino)

Providing all materials, labour, T&P for fitting and fixing HPL Urinal partition Made of 12 mm thick compact laminate total height 1195 mm , Depth 450 with duties, transportation etc. all complete as per specification & direction of Engineer-in-charge. (Make: Greenlam/Merino)

Providing all labour, T&P and machinaries for installation,commissioning of Three phase sensor with level indicator (Domestic OHT & UGR) and cables etc as per requirement

Supply, installation,testing & commisioning of water cooler cum purifier with chiller in floor of following capacity including fixing the same on the floor with necessary water connection & waste waste arrengments with all labour, T&P etc.all complete as per the specification. SS 304 Storage Cooler cum UV +RO Water Purifier 120 lit Capacity 60 ltr per hr cooling capacity, 120 ltr storage Model-AG Green Pure Chill 120SS UV (Eureka Forbes/Kent)

Internal & External Water Supply

Providing and fixing Microcellular Closed Cell Nitrile Rubber Insulation in tube form for insulation of pipes/ducts, having a density between 40-60 Kg/M³ and a thermal conductivity ($\lambda$) not exceeding 0.040 W/m·K at +20°C or 0.042 W/m·K at +40°C ; the material shall have a high moisture resistance factor ($\mu$) of > 4000 and be suitable for an operating temperature range of -40°C to +105°C ; the insulation shall meet Class 1 fire performance as per BS 476 Part 7 and be self-extinguishing and non-dripping ; the material must be CFC/HCFC free and dust/fiber-free for health compliance; installation shall be carried out using manufacturer-recommended cold adhesive, ensuring all longitudinal and transverse joints are sealed airtight with adhesive and finished with 50mm wide self-adhesive Nitrile Rubber tape, including the cost of all materials, labor, and scaffolding as per the direction of the Engineer-in-Charge." (As per K-FLEX EC Class 1 or equivalent)

25mm dia insulation

28mm dia insulation

35mm dia insulation

42mm dia insulation

54mm dia insulation

Cast iron Y type Strainer flanged (Make:Zoloto/Leader)

50mm dia

65mm dia

Forged brass PRV (Make:Zoloto/Leader)

25mmm dia

32mmm dia

Internal Sewage & Rainwater System

Providing, fixing, jointing and testing PP mineral filled low noise Soil ,Waste, Vent & Rainwater piping system as per BS EN 1451, SN4-S16, with minimum density for pipes and fittings 1.4 gm/cm3. Pipes and fittings made from Polypropylene-M (mineral reinforced) and available from 50 – 160 mm with push fit SBR type rubber ring sockets for easy installation. Pipes should have 3 layer design and hot water resistance up 95ºC for short term loading (90ºC for long term loading). Piping system should have chemical resistance of pH 2-12. Fittings should have swept design from 75-160mm and depth gauge for proper fittings against thermal expansion and contraction with top marking at every 15° intervals in angular rotation for better alignment. Piping system includes all required fittings & accessories such as coupler, bend, tee, Y, reducer, access pipe, multi floor traps, Nahni trap with extension piece etc. for conveying soil, waste & rainwater purpose in floors, ceiling suspended, or on walls, with leak proof joints etc. Setting the pipe in 1:2:4 CC in case of concealed plumbing, wall chasing, holes, supporting, clamping, covering back with chicken mesh & plaster and making the wall good as per approved drawing. Testing as per tender specifications/EIC. Make:ASTRAL/HULLIOT

110mm dia pipe

75mm dia pipe

50mm dia pipe

Supplying and fixing of following dia PP (Ringfit) fittings of approved make confirming to BS EN 1451 in all floor with all transportation & requisite testing as per specification & direction of EIC. Make:ASTRAL/HULLIOT

110mm Pushfit Coupler

110mmx87.5º bend

110mmx87.5º door bend

110mmx45º bend

110mm dia Swept Tee

110mm dia Swept Tee with Door

110mm dia Single 'Y'

110mm dia Single 'Y' with Door

Clamp Suitable for 110mm dia pipe

110mm dia Vent cowl

110mm Socket plug

75mm Pushfit Coupler

75mmx87.5º bend

75mmx87.5º door bend

75mmx45º bend

75mm dia Swept Tee

75mm dia Swept Tee with Door

75mm dia Single 'Y'

75mm dia Single 'Y' with Door

Clamp Suitable for 75mm dia pipe

75mm dia Vent cowl

75mm Socket plug

50mmx87.5º bend

50mm dia Swept Tee

7 inch Multi floor trap (110 x 75 x 50(3) mm)

External Sewage

Providing and fixing in position pre-cast Heavy Duty FRP manhole cover and frame of shape 900 mm dia (25TN load bearing capacity)

Recharge pit, Borewell, Pumps, WTP & STP & other works

Borewell pump

Supplying all materials, labours, T&P and providing fitting & fixing submersible pump with squirrel cage induction type submersible type submersible electric motor to run on 3 phase /1 phase line voltage ranging from 320 volt to 450 volt conforming to Si 8034/89 with following specifications with suitable control panel ,jointing with GI/PVC/HDPE pipes,electrification,testing, commissioning ,trial running, conveyance of all materials to worksite all complete as per specification & direction of the Engineer in charge. Make- KIRLOSKAR/XYLEM/ARMSTRONG

Borewell Submerssible Pump Set 1.00 H.P single phase 3 stage head range 30 to 54 metres, discharge 155 to 200 LPM with control panel & all necessary cables

Installation of Surface Pump set. (From UGR to OHT)

Supply all materials, labour, T&P and providing,fitting and fixing horizontal surface centrifugal pump with electric motor to run on three phase conforming to IS:8034/89 with following specifications with suitable control pannel, jointing with GI/PVC/HDPE pipes,electrification, testing,commissioning,trial running, conveyance of all materials to worksite, all complete as per specification and direction of the Engineer in charge.. Make- KIRLOSKAR/XYLEM/ARMSTRONG

3 HP three phase 5 stage head range 38 to 59 metres, discharge 250 to 300 L.P.M with outlet dia of 50mm (1W+1S) with control panel & all necessary cables

Installation of Submersible Pump set (Basement Dewatering Pump, Fire Pumproom)

Supply all materials, labour, T&P and providing,fitting and fixing submersible pump with squirrel cage induction type submersible type submersible electric motor to run on single phase line voltage ranging from 320 volt to 450 volt conforming to IS:8034/89 with following specifications with suitable control pannel, jointing with GI/PVC/HDPE pipes electrification, testing,commissioning,trial running, conveyance of all materials to worksite,complete as per specification and direction of the Engineer in charge.. Make- KIRLOSKAR/XYLEM/ARMSTRONG

2 HP three phase 5 stage head range 15 to 20 metres, discharge 250 to 300 L.P.M with outlet dia of 50mm (1W+1S) with control panel & all necessary cables.

Providing all design, drawing,Supply, Installation, Testing, commissioning of Water Treatment Plant of capacity 5 CUM/hr considering 6hr daily operation. System comprising of Activated Carbon filter, Sand media filter, softner filter and Chlorine dosing disinfection system, UV , Iron remover (if required as per water test report) including feed pumps (1W+1S), control panel, auto level sensors, backwashing arrangements, automation and related plumbing like pipes, valves, strainers etc with suction from raw water tank and delivery into treated water tank.including all leads and lifts, testing etc

Operation and Maintenance of STP and WTP for 5 years after the date of commissioning

Supply all materials, labour, T&P and providing,fitting and fixing booster pump with pressure tank, pressure switch, transmitter, pressure gauge with specifications of 20m head and 200 LPM discharge each pump (1W+1S) with suitable control pannel, jointing with GI/PVC/HDPE pipes electrification, testing,commissioning,trial running, conveyance of all materials to worksite,all complete as per specification and direction of the Engineer in charge.. Make- KIRLOSKAR/XYLEM/ARMSTRONG

Providing, fabricating, supplying and fixing M.S. Steel Liner (Pile Casing) of 4 mm thickness, made from IS 2062 Grade E250 structural steel plates, including cutting, rolling, edge preparation, welding, lifting hooks, alignment, erection, temporary stiffeners (if required), all labour, consumables, tools & plants, loading, unloading, transportation, and complete installation in position as per approved drawings and the direction of the Engineer-in-Charge. The rate shall include all incidental charges required for satisfactory completion of the work.

Constructing underground RCC Septic Tank for 100 Users complete with Soak Pit, inspection pits, including all structural, masonry, waterproofing, plumbing, and finishing works as per approved drawings and direction of Engineer-in-Charge.

Total

Add GST @ 18 % in total of above all items.

Total with GST

Add Labour Cess @1%

Grand Total =