Special Strengthening Of Jarwahi Baruka Road Length 6.24 K.m. and Special Strengthening Of Lafda Sahi Khairi Road Length 4.70 K.m. Total Length- 10.94 Km

Repair to pot holes and removal of loose material, trimming of sides, cleaning of surface by providing tack coat with bitumen emulsion, 20 mm thick pre-mix carpet using catonic bitumen emulsion @ 21.5 kg per 10 sqm and seal coat type B with bitumen emulsion @ 10kg per 10 sqm as per technical specification and compacting with three wheeled 80-100 kN Static Roller.

Repair of Pot Holes, Patch Repair Providing, laying and rolling of built-up-spray grout layer over prepared base consisting of composite construction of compacted crushed coarse aggregates and key stone chips with application of bituminous binder after each layer, and with key aggregates placed on top of the final layer to serve as a Base conforming to the line, grades and cross-section specified, (number of layers of coarse aggregate shall be as per site requirement).

Wet Mix Macadam Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification includingpremixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density in accordance to Table No. 400-12, 400-13 and as per clause of section 406 of specifications.

Deduction for item No.4.3 if sensor paver is not used.

Prime Coat Over WMM/WBM (i) Providing and applying primer coat with catonic bitumen emulsion on prepared surface of granular Base including cleaning of road surface and spraying primer at the rate of 0.70 to 1.00 kg/sqm using mechanical means as per clause 502 of specifications

Providing and applying tack coat with low viscosity bitumen of VG 10 grade using bitumen pressure sprayer on the prepared bituminous/granular surface cleaned with mechanical broom and as per relevant clauses of section-503 of specifications. (i) @ 0.25 kg per sqm (normal bituminous surfaces)

(ii) @0.30 kg per sqm (dry & hungry bituminoussurfaces / granular surfaces treated with primer)

Dense Graded Bituminous Macadam Providing and laying dense bituminous macadam using crushed aggregates of specified grading, premixed with bituminous binder @ 4.0 to 4.5% by weight of total mix of mix and filler, transporting the hot mix to work site, laying with a Electronic Sensor paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per clause 505 of specification complete in all respects b) Using Drum Mix Plant of appropriate capacity (iv) for Grading II (26.5 mm nominal size) Bitumen Content minimum 4.5% with bitumen 60/70 (VG 30)

Bituminous Concrete Providing and laying bituminous concrete using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 % by weight of total mix of mix and filler, transporting the hot mix to work site, laying with an Electronic Sensor paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory tandem and pneumatic tyre rollers to achieve the desired compaction as per clause 507 of specification b) Using Drum Mix Plant of appropriate capacity (v) for Grading-II (30-40 mm thickness) Bitumen Content minimum 5.4% with 60/70 bitumen (VG-30)

Construction of Shoulders with approved material/selected soil i/c excavation all lifts & leads i/c grading to required slope & camber of 4% and compacting using vibratory roller of 80 to 100 kN static weight to meet requirement as per relevant clause of 400. (B) Hard Shoulders (CBR value >12)