IMPROVEMENT OF SERVANT QTRS OF CERTAIN OFFRS MD ACCN, PROVN OF SENTRY BOX FOR GORKHA HILL BLOCK NO 1 AND 2, PROVN OF CORNER WASH BASIN IN GH 23-29, 40 TO 42 AND PROVN OF SEATING / BENCHES WITH COVERED SHED AT DSSC WELLINGTON

Taking down chowkats or frames including shutters (without taking off shutters from the frames) not exceeding 1.50 Sqm each complete all as specified and directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frames) exceeding 1.50 Sqm and not exceeding 4 Sqm each, complete all as specified and directed.

Demolition of cement concrete (unreinforced ) (below or above ground level) and removing debris off the site complete all as spcified and as directed.

Taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and as directed.

Demolition for brickwork or stone masonry laid with cement mortar or cement lime mortar all as specified and as directed.

Demolition of cement concrete (reinforced) of any decscription and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for coloured non skid ceramic tiles7 to 8 mm thick (square/rectangle) area of each tile exc 0.06sqm but not exc 0.11 sqm, in floors and sill etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:4 complete all as specified

Dittoall as per item No 7 above but set and jointed in neat cement slurry and pointed in coloured cement to match as in vertical surfaces of dado/skirting set in 10mm thick CM 1:3 complete all as specified

M&L for coloured glazed ceramic tiles of size 350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match as in vertical surfaces of dado/skirting set in 10mm thick CM 1:3 complete all as specified

S&F Pressed steel frames of 1mm thick factory made of size 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc and providing one shop coat of primer and taring back side of frame, complete all as specified.

Supply and fix factory made 35mm thick flush door shutters, solid core construction, with block board core and plywood face panels, commercial type Decorative face on both sides with lipping to match with frame and fitted to chowkats etc., complete all as specified and as directed.

M&L for 2nd class hard wood (Sal / Hollock) factory made glazed and skeleton shutters 35 mm thick, open rebated and prepared to receive glass or gauge,etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (a) for door shutter supplying and fitted to chowkats, complete all as specified and directed..

Supply and fix Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing

Supply and fix Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded wood grain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and wood grain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of wood grain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing.

M&L PCC type B-0 (1:2:4) using (12.5mm graded aggregate) as in filling of steel chowkats or frames complete all as specified and as directed.

S&F Mild steel butt hinges 100mm long, medium weight, cold rolled.

S&F 150mm, extruded aluminium alloy handles, fabricated type, anodised complete.

S&F 150 mm long, Aluminum anodised barrel tower bolts, of extruded section complete as specified and as directed.

S&F 300mm long, Aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed complete as specified and as directed.

S&F Stainless steel wire cloth0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Supply and fix Aluminium powder coated sliding widnow with apprprate frame section(with two or three track) including two or more window shiutters with 5.5mm thick plain glass and including on or more gauged shutter including jointing cleat, glazing clips, rubber neopreone packing including necessary accessories like handles, hinges etc complete all as specified and directed.

Supply and fix Aluminium powder coated openable/side hung ventelator with apprprate frame section including 4 to 5mm thick pin head or hatched glass with louvers design all as directed by the Engr Incharge including provn ogf appropriate opening for fixing of exhaust fan and including with or wthout gauged shutter including jointing cleat, glazing clips, rubber neopreone packing including necessary accessories like handles, hinges etc complete all as specified and directed.

Excavating in trenches, n.exc 1.5m wide and n exc 1.5 in depth; for foundation getting out hard/dense soil.

Material and labour for providing plain cement concrete 1:3:6 type C2, using( 40mm graded stone aggregate )as in foundation filling and mass concrete for manhole&Septic tank all as specified and as directed.

M&L for Precast cement concrete block Type C1(1:3:6)(using 20 mm graded aggregate) masonry with solid solid blocks exc 10cm width and setting in mortar(1:6) complete.

Providing precast cement concrete solid building blocks or slabs 10cm thick type B-1 using 20mm graded stone aggregate and setting in mortar,(1:4) complete, in walls all as specified and as directed.

M&L for Reinforced cement concrete (nominal mix) type B- 1(1:2:4) using 20mm graded stone aggregate as in Beams, cantilevers,band , bressummers,lintels over 1.5m span etc all as specified and dircted.

M&L for RCC Type B1-1:2:4 (using 20mm graded aggregate )as in slab supproted on walls, beam and columns in floor, roof/cooking platforms etc

M&L Formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers,lintels, cantilevers, shelves,kitchen platform,foundation for post etc all as spd and directed.

S&F TMT bars Mild steel bars 10mm and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

all as item No 31 above but but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

M&L 15mm thick rendering plaster on fair face of brick-work or concrete surface incl finish the surface even and smooth without using extra cement in CM 1:6 complete all as specified and as directed .

M&L 15mm thick rendering plaster brick or concrete surface in CM 1:4 including adding water proofing compound as per manufactures instruction complete all as specified and as directed .

Material and labour for rendering 5mm thick in Cement Mortar 1:3 on concrete surfaces of ceiling chajja etc , finished even and smooth without using extra cement complete all as specified and as directed.

M & L for mild steel work as in tubular roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat, square tube etc sections) including distance pieces, cleats etc. Fe 410-W (Gde-E- 250) quality- A complete all as specified and as directed.

M/L preparing new surface of steel and appling two coats of synthetic enamel paint over a coat of primer red oxide

S & F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet crumped where ever required 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof coverings fixed with self tapping screws complete all as specified and as directed.

M & L for PCC (1:3:6) type C-1 (using 20 mm graded stone aggregate) as in padding, coping, bed plates, hold fast blocks, sunken floor sub bse etc., including formwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

M&L hardcore of gauge n.exc 63 mm deposited, spread & levelled in layers n. exc 15 cm thick, watered & rammed to a true surface with broken stone or boulders complete as specified and as directed.

M&L 75mm thick Plain Cement Concrete type C-1, 1:3:6 (20mm graded stone aggregate) as in floors, pavings finished even & roug without using extra cement complete as specified and as directed.

M&L for providing and laying water proofing treatment to sunken floor portion of WC ,Bathroom etc,by applying first layer of slurry of cement @0.488 kg/Sqm mixed with Dr fixit or Equivalent Acrylic based polymer modified cementitious (PMC) composite compound @ 0.253kg/sqm and second layer of slurry of cement 0.242 kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @0.126kg /sqm complete all as specified and as directed.

M & L 20mm thick cement screed in cement mortar 1:3 mixed with liquid water proofing compound FOSROC's complast 421 IC @ 130ml per bag of cement including a bonding coat of FOSROC's Nito bond AR cement slurry for roofcslab/ floor complete all as specified (liquid water proofing compound are measure seperately)

M&L PCC 1:4:8 type D2 with 40mm graded stone aggregate as in sunken floor/toilet floor /kitchen floor concrete finished the surfaces even and fair to receive top layer all as specified and as directed.

M&L Providing 25mm thick cement concrete type B0, 1:2:4 using 12.5 mm graded stone aggregate .as in floors for levelling course including finish the surface even and rough to receive the top finish complete all as directed.

Taking down steel tubing and connections of 15 mm bore including cleaning for refixing or removal to store complete all as specified and as directed.

Taking down steel tubing and connections of 20 mm bore including cleaning for refixing or removal to store complete all as specified and as directed.

Taking down steel tubing and connections of 25 mm bore including cleaning for refixing or removal to store complete all as specified and as directed.

Refixing of old GI steel tubes and connections after cleaning of 15 mm bore in new or old position, any grade, to walls, ceiling, floors, etc complete all as specified and as directed.

Refixing of old GI steel tubes and connections after cleaning of 20 mm bore in new or old position, any grade, to walls, ceiling, floors, etc complete all as specified and as directed.

Refixing of old GI steel tubes and connections after cleaning of 25 mm bore in new or old position, any grade, to walls, ceiling, floors, etc complete all as specified and as directed.

S&F 15 mm bore Galvanised iron tubing, medium grade, with all fittings laid in trenches, floors or fixed to walls etc complete all as specified and as directed.

S&F 20 mm bore Galvanised iron tubing, medium grade, with all fittings laid in trenches, floors or fixed to walls etc complete all as specified and as directed.

S&F 25 mm bore Galvanised iron tubing, medium grade, with all fittings laid in trenches, floors or fixed to walls etc complete all as specified and as directed.

Dismantling existing tanks exc. 500 lit & n. exc. 1000 litres capacity, removing off the site complete all as specified and as directed.

Supply and Fix, 1000 litres capacity triple layered Rotational Moulded Polyethylene (HDPE) FDA grade materials water storage tanks, (Cylindrical vertical with closed top) screwed lid type conforming to IS 12701-1996 with manhole lid and suitable locking arrangement including making holes for inlet, outlet, washout and over flow pipes, hoisted and fixed in position as specified in SSR Part -I (2009) complete all as specified and as directed. Make: Sintex/Polycon/Vectus

Meterial and labour for Providing, cement concrete type B-0 ,1;2:4 usinf 12.5mm graded stone aggregate in roof kerbs ,koving for chajja or mud stops, rounded or chamfered on edges etc all as directed by the Engr In charge

S&F and in 25mm bore, Ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed,weight 455 gms complete as specified and as directed.

S&F in 25mm bore, Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete as specified and as directed.

S&F 20mm bore, Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete as specified and as directed.

Cutting chases, pinning in, making good to facings where required & pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc; & cutting chases for concealed water tubing or concealed conduit wiring, etc.& making good, cutting not exc 10 cm grith in brick wall

Supply and fix in repairs 18mm thick High Density High Moisture Resistant (HDHMR)/HDWR Board, both side laminated of approved colour as in shutters, back board, vertical support and horizontal shelves of kitchen/bedroom cupboards fixed with screw to timber framed work etc., including dismantling of existing any type of board and complete all as specified and as directed.Note: All exposed edges/surfaces to be finished with same laminated sheet to match with the other surfaces and nothing will be paid extra.

Material and labour for Aluminium designer powder coated decorative curtain rods (Drapery rods) 20mm dia, exterior grade 3mm thick with and including side caps, holding clamps and 'F' and 'L' brackets, fixed to wall with PVC rawl plug and brass screws etc., complete all as specified and as directed.

Material and labour for Granite work with 20mm thick machine cut, Jet Black granite slab in single piece or two piece length, table rubbed and polished, laid over and including 20mm thick cement screed in cement mortar 1:4 bedded and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust and admixture of pigments to match with shade of granite stone as in cooking platforms, microwave platform, WHB counter top in steps, jambs, pillars, window-cills, etc, including cutting, polishing and rounding to edges of stone slabs etc., complete all as specified and as directed.

Material and labour for providing plain cement concrete 1:3:6 type C2, using( 40mm graded stone aggregate )as in drain / surface channel including necessary form work complete all as specified and as directed.

Supply and fix in repairs stainless steel telescopic ball bearing channel, zinc plated finish for drawer including necessary fittings up to length of 600mm fixed with screws complete all as specified and directed.MAKE: EBCO/ GODREJ / KAFF / HETTICH

Supply and fix in repairs Stainless steel soft close hinge with 35mm cup dia, full overlay, 110 degree opening suitable for 18mm thick shutters complete all as specified and as directed. MAKE: EBCO/ GODREJ / KAFF / HETTICH

Supply and fix in repairs Gun metal handle of size 150mm for kitchen/bedroom cupboards fixed with screws complete all as specified and directed. MAKE: EBCO/ GODREJ / KAFF / HETTICH

Supply and fix in repairs Magnetic closer of suitable size for kitchen/bedroom cupboards fixed with screws complete all as specified and directed. MAKE: EBCO/ GODREJ / KAFF / HETTICH

Supply and fix 50 mm bore Low density poly ethylene pipes (LDPE) of pressure rating 6 kg/sqcm in any length with rubber ring joint complete all as specified and as directed.

M&L for chequered cement concrete tiles of size 20cmx20cmx 25mm thick ,set ,jointed and pointed in neat cement slurry in floors with grey cement and pigments of required colour over 20mm thick thick screed bed in CM (1:6) complete as specified and as directed.

Returning filling including spreading leveling watering and well ramming in layers not exc 25 cm hard and dense soil

Removing excavated material exc 1.50km but n exc 5.0km and depositing where directed (Soils) at a level not exc.1.5mts above the starting point

Supply and fix two way Bib cock 15 mm bore, cast copper alloy, chromium plated, fancy type with flange and crutch or butterfly handle conforming to IS as per Cat No.CON-041 of Jaquar or T3534A1 of Parryware or specified makes, screwed down high pressure with fly nuts, screwed for iron pipes or for brass ferrule etc., complete all as specified and as directed.

S&F health faucet Make:Cat No. E8342A1of Parryware /F160001 of Hindware/ ALD-CHR 565 of Jaquar including 1.2m long flexible tube and wall hook complete all as specified and as directed.

S&F in repair bib cock long body with wall flange .Make: Cat No G1405A1 of Parryware/ F730011 of Hindware / CON 107 KN of Jaquar or equivalent all as specified and directed.

S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes;including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete.

Supply and fix in repairs, stainless steel plate racks made of stanless steel 0.80mm thick sheet standard size 24'x36x10" and design as approved by GE, complete all as specified and as directed. Make: Nirali/Parryware as approved by GE.

Supply and fix in repairs corner glass shelf made out of glass with cp guard rail and wall fixing accessories of 300mm radius matt finished, chromium plated (MCH/Colour CP) with brass brackets as per Cat No.ACN-1173 of Jaquar or T6010A1 of Parryware fixed on walls complete all as specified and as directed .

Supply and fix in repairs Angular stop cock 15mm bore, cast copper alloy, chromium plated, fancy type with long shank conforming to IS as per Cat No.CON-053KN of Jaquar or G3053A1 of Parryware, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified and as directed.

S&F as in repairs Viterous china wash down water closet pan (pedestal pattern) and 'P' or 'S' trap including fixing bolts, PVC bend, seat cover and connecting to PVC (SWR) pipe, complete all as specified (Excl flush tank): Make : Prayag or equivalent in Paryware/Hindware

Supply and fix vitrious china wash hand basin (corner fix pattern) including waste pipe,waste coupling ,etc) fixed on wall including necessary cutting of wall and including brackets and making goood the surface etc complete .

S& F Pillar cock cromium plated with wall flange complete .screwed down high pressure, with or without lettered Hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in repairs complete all as specified and directed.Make : CERA ,Cat part No : QTF2006101,

S&F as in repairs PVC valveless, symphonic action type low level flushing cistern white with inlet, ball valve, float and handle etc complete capacity 10 litres including brackets and upto 1mtr long PVC pipe of 40mm dia and bend complete all as specified and directed.

S&F in repairs Towel rail 600mm long complete all as specified Make : Prayag Cat No GBA-131 or equivalent in Parryware/Hindware)

S&F in repairs soap dish complete all as specified Make : Prayag Cat No GBA-151G or equivalent in Parryware/Hindware)

S&F in repairs 5.50mm thick looking mirror of size 600 x450mm mounted on 6mm thick plywood backing or AC sheet backing including framing with 2nd class hard wood of size 30mm x40mm decorative type polished and fixed to wooden plugs with cromium plated brass screws and cupwashers and chamfered glass from all sides fixed with steel screws all as specified and directed.

S&F in repairs, two piece type stainless steel gratings square or round 100 mm size complete all as specified and as directed..

S&F in repair PVC connection 15 mm size with PTMT nuts of length 450 mm.

Taking down Cast iron / PVC pipe 75mm/ 110mm jointed in cement mortar taking out of wall. including all fittings, heads, sheos, bends, swan-necks, etccomplete all as specified and as directed.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/trenches complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S & F PVC (SWR) bends any radious 110 mm bore provided with acess door.

S & F PVC (SWR) bends any radious 75mm bore provided with acess door.

S & F PVC (SWR) vent cowl 110 mm bore

S&F in repair 75 mm dia PVC floor trap with cockroach trap and grating (double bowl type) with hole for waste pipe in grating including jointing to waste pipe complete all as specified and as directed.

S&F in repair 100mm dia PVC floor multi trap with and grating of size 100 x 100 mm complete all as specified and as directed.

Supply only liquid water proofing compound of approved make complete all as specified and as directed.

S&F in repairs double coat hook with brass brackets Make.Cat No 6905A1 of Parryware/ F580007 of Hindware / ACN -1161N of Jaquar or equivalent all as specified and as directed.

Complete removal of existing treatment on external walls by wire brushing, crack filling & Bio-wash to fight microbial growth and applying, one coat of exterior wall primer and two coats of Exterior Emulsion anti fungal weather proof paint complete all as per manufacturer instruction as directed: NOTE: The painting work to be executed by authorised applicator of the manufacturer.Make :-APEX ULTIMA OF Asian Paint or WEATHER COAT SMOOTH of Berger or Nerolac Excel Top guard of Nerolac

M&L Preparing newly plastered surfaces of external walls and applying one coat of exterior wall primer and two coats of Exterior Emulsion anti fungal weather proof paint complete all as per manufacturer instruction as directed.Make:APEX ULTIMA OF Asian Paint or WEATHER COAT SMOOTH of Berger or Nerolac Excel Top guard of Nerolac

M&L for preparation of new surfaces of walls and applying with white putty of average thickness 3mm and making the surface to an even and smooth finish by rubbing with sand paper of different grade etc and applying two coats of Oil bound distermper over a coat of primer by approved applicator of the manufacturer of the paint and all as specified and as approved.

M&L for complete removal of existing treatment on surfaces of ceiling and applying two coats of white wash complete all as specified and as directed.

M& L surface excavation n.exc 30cm deep and averaging 15 cm deep and getting out in hard/ dense soil

M&L Reinforced cement concrete using Type B1 1:2:4 20 mm graded stone aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete.

M&L Reinforced cement concrete using Type B1 1:2:4 20 mm graded stone aggregates as Columns, pillars, piers, posts and struts

M&L use and waste of timber as in formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, for fair finished surfaces of concrete flat.

M&L use and waste of timber as in formwork to sides of square or rectangular pillars, posts, struts, piers, columns and stanchions for fair finished surfaces of concrete flat.

M&L use and waste of timber as in Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for fair finished surfaces of concrete flat.

M&L use and waste of timber as in formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surfaces of concrete flat.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:4

M&L Rendering 10mm thick CM 1:6 on fair faces of brick work or concrete surfaces all as specified and as directed

M&L Rendering 15mm thick CM 1:4 on fair faces of brick work or concrete surfaces incl finished even and smooth (without using extra cement) all as specified and as directed

M&L PCC 1:4:8 type D-2 using 40mm graded Aggregate in sub base 100mm thick.

M&L PCC 1:2:4 type B-1 using 20mm graded Aggregate in floor 25mm thick.

M/L for non skid coloured ceramic tiles ( of any colour) flooring 7 to 8 mm thick area of each tile exceeding 0.06 sqm and not exc 0.11 sqm with joint free tiles set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick cement screed bed in CM 1:4complete.

M& L for applying three coats of white wash on walls including preparation of newly plastered surfaces of wall complete all as specified and as directed.

M&L two coats of cement based paint over a coat of white wash on new plaster surfaces incl preparation complete all as specified and as directed.

M/L for PCC 1:2:4 type B1 using 20mm graded aggreages as in hardstanding /approaches of 75mm thick incl finished even and smooth (without using extra cement) all as specified and as directed complete all as specified and as directed

M&L for Roof tiles, Mangalore pattern, interlocking at side joints, laid dry complete all as specified and as directed.

Ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in lime mortar 1:3 or cement mortar 1:6 complete all as specified and as directed.

The profile for costruction of UPVC Door will be of overall size 60x58 mm with wall thickness 2.7 + or - 0.2 mm extruded sections. The corners will be plastic welded.The hinge side vertical outer frame shall be reinforced with galvanized channel of wall thickness 1.2 mm. The door will be fixed to walls using 8 mm dia 80 mm dia MS screws minimium 3 nos on each sicde. The glazing will be fixed to door frame with UPVC standerd beadings of 24.5 x 16 mm of 2 mm thick.The bottom portion of door for 1 m height will be provided with UPVC hollow board not less than 6 mm thick. The door shutter will be fixed to frame using 3 nos of 3 D hinges. The door will be provided with one mortice lock with powder coated handle and two powder coated MS tower bolts. Note: The entire fixing will be done as per manufactures instructions and specification and as directed.

Supply and fixing factory made uPVC white colour Two track two panels sliding glazed window upto 1.50m height made of (small series) frame 52 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm) comprising of uPVC multi-chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, incl 4.8mm thick glass complete all as specified and directed by Engineer-in-Charge.Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made complete all as specified and as directed.

Dismantling floor, hearth or wall tiling of any description and any thickness incl cement mortar bedding (but not backing), rubbish off the premises.

Cutting holes into or through but in stone walls built in cement mortar or cement lime mortar and walls of cement concrete.

S&Fcorner racks with glass with brass brackets chromium plated railings of Cat No -T6910A1 Parryware or equivalent in Cera/Hindware/ Jaquar all as specified.

S&F 15mm dia Angular valve with wall flange all as specified.

S&F two piece type stainless steel gratings square or round 100 mm size with waste hole complete all as specified and as directed..

S&F wash basins, vitreous china of size 450 x 300 (corner type) or nearest higher size with and including CI brackets and 32mm waste coupling, waste pipe etc and cutting for and pinning in ends of brackets or erecting stand, making necessary connections to Pillar tap, PVC Connection, waste pipe / bottle trap etc., complete all as specified and as directed. Note: (i) The unit rate quoted shall be deemed to include the cost of Corner basin, brackets, 32mm waste couplings and waste pipe. (ii) Pillar tap and PVC connections shall be measured and paid separately.

Supply and fix Pillar tap 15 mm bore, cast copper alloy with capstan heads, chromium plated, fancy type, confirming to IS, screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipes, complete all as specified and as directed.

S&F Bib cock (Two in one) with health faucet multi type including flexible hose Cat No T1381A1 Make -Parryware or equivalent in Cera/Hindware/ Jaquar all as specified and as directed.

S&F PVC connections 15mm size with brass nuts of length 600 mm each complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to floors complete all as specified and as directed.

S & F PVC (SWR) bends any radious 75mm bore provided complete all as specified and as directed.

Excavating in post holes (or similar holes) each n.exc 0.5 cum getting out hard/dense soil returning, filling and well ramming earth or broken rubble, mixed with earth around, in layers not exc 25 cm

Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

Pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

Supply and placing of Cast Iron 3 - seater FRP Garden Bench for outdor park with black and wooden texture with ornamental design framed work with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding steel members as necessary, and fabrication of wooden planks with screws in seating upto head rest level with even and smooth finish complete all as specified and directed

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.. complete all as specified and as directed.

All as per item No 141 above but b) One 5 amps 5 Pin socket outlet on independent board

All as per Item No 141 above but with FRLS PVC insulated copper conductor cable of size 2.5 Sqmm 3 pin socket outlet, 16 amps, independent complete all as specified and directed.

S&F Modular type socket out let 2/3 pin, 6/16 Amps, 2 module all as specified and as directed.

S&F Modular type Socket outlet 6 Amps 2/3 Pin, 2 module complete all as specified and as directed.

S&F Modular type switch single pole 16 Amps one way, 1 module all as specified and as directed

S&F Modular type switch single pole 6 Amps, 1 module, one way all as specified and as directed.

S&F Modular type Bell switch single pole 6 Amps one way, one module all as specified and as directed.

S&F Call Bell, AC, ding dong type 230 Volt complete all as specified and as directed.

S&F ceiling rose surface mount PVC/Polycarbonate, isolated body with face bakelite two/three terminals complete all as specified and directed.

S&F modular white cover plate with frame, 3 module complete all as specified and directed.

S&F modular white cover plate with frame, 6 module complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC , (4 ft.) High performance electronic driver , operating temperature 10 C to 35 °C operating voltage range 140 V -270 V , Average life 50000 hours and LED lamp including High efficiency long life LED with lumen efficacy of 140 Im/watts and ABS end caps tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make Havells cat part No LUMILINEPLUSPROBS20WLED865SPCSSIND OUG G

Supply and fixing LED lights fitting 1x 10W, 220V, AC , (2 ft.) High performance electronic driver , operating temperature 10° C to 35 °C operating voltage range 140 V -270 V , Average life 50000 hours and LED lamp including High efficiency long life LED with lumen efficacy of 140 lm/watts and ABS end caps tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make Havells cat part No LUMILINEPLUSPROBS10WLED865SPCWHIND or equivelent

S & F SPN DB, 8 Way, Metal double door type 240 volts fitted with 200 Amps rated busbar and blanking plates, neutral link and making good the disturbed surfaces with all other accessories including necessary connection all as specified and directed.

S&F Miniature circuit Breakers, SP,C-Series 240 Volts of capacity 6-32 Amps with breaking capacity 10 kA all as specified and dircted.

S&F Miniature circuit Breakers, SPN of capacity 6-32 Amps,C-Series 240 Volts with breaking capacity 10 kA all as specified and dircted by Engr-in-Charge.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and directed

Material and Labour for Submain wiring with 2 runs of FRLS grade PVC copper conductor cable 4 sqmm, multistranded along with FRLS grade PVC insulated copper earth continuity conductor 4 Sqmm drawn through and including PVC Conduit pipe 20 mm dia with all fittings including taking down old unsv submain wiring complete all as specified and directed. Note: The cost for concealed submain wiring is deemed to be inclusive of cutting chases in stone masonary wall/roof and making good.

M&L for point wiring complete with 1.5 Sq mm single core PVC insulated FRLS unsheathed cable 1100 Volts grade with multi stranded copper conductor confirming to IS 694 1990 with ISI marked ( for phase, netural and earth ) in and including PVC conduit with ISI mark of minimum 20 mm ia and all accessories concealed including / cutting / chases in wall / ceiling /fixed to roof /truss/ columns etc and including factory made branded make embossed glvanised steel pressed terminal boxes alongwith suitable size modular cover plates with frames for fixing modular switches and sockets , fan regulators etc. of suitable size and the earth wire to connected to common earth dolly complete all as specified and directed for one light point / fan / call bell point controlled by one modular switch 6 A one way. Note : Location of light points , 6 Amps socket point and light fitting may be decided by Engr-in-charge as per site / user requriement.

All as per item no 160 above but 3 pin socket out let 5/6 Amps on independent board

M&L for point wiring complete all all as specified with 1100 Volts grade 4 sqmm single core PVC insulated FRLS 1000 Volts grade with multi stranded copper conductor confirming to IS 694 1990 with ISI marked ( for phase, netural and earth ) in and including stove enamelled steel conduit with ISI mark of minimum 20 mm ia and all accessories concealed including / cutting / chases in wall / ceiling /fixed to roof /truss/ columns etc and including factory made branded make embossed glvanised steel pressed terminal boxes alongwith suitable size modular cover plates with frames for fixing modular switches and sockets , fan regulators etc. of suitable size and the earth wire to connected to common earth dolly complete all as specified and directed for one three pin modular switch socket 16 Amps outlet on independent board

Supply and fixing LED lights fitting 1x 20W, 220V, AC , (4 ft.) High performance electronic driver , operating temperature 10 C to 35 °C operating voltage range 140 V -270 V , Average life 50000 hours and LED lamp including High efficiency long life LED with lumen efficacy of 140 Im/watts and ABS end caps tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make Havells cat part No LUMILINEPLUSPROBS20WLED865SPCSSIND OUG G

Supply, laying, jointing & testing XLPE insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size10 sq mm 4 core in trenches / through GI pipe / fixed along with pole structure etc with all fixing & connecting accessories incl taking down old cable complete all as specified & as directed. Note :- Necessary earthwotk, PCC etc shall be measured & Paid separately under relevant items of works

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for taking out/laying of UG Cables, GI Pipe etc. and getting out in hard dense soil complete.

Returning, filling in including spreading, levelling, watering and well ramming in layers n.exc 25cm thick.

Removing of excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point.

Supply, spreading and compacting of riddled earth in trenches for cable cushion on both top and bottom of cable, including ramming complete all as specified and as directed.

Supply and laying sub class "B" bricks in trenches for protection of UG Cable with width equal to length of bricks, laid dry & flat complete all as specified & as directed.

Supply and fixing GI pipe light grade (ISI Marked) of size 40 mm for cable protection to be fixed on pole with necessary clamps complete all as specified and directed Note :- Unit rate quoted is deemed to be inclusive of MS clamps of suitable size/number along with nuts/bolts/washers etc. to be fixed on pole.

S&F MCCB, 4 pole,63A rating (Ics = 100% Icu),415Volts,16 KA Breaking capacity,with adjustable thermal and fixed magnetic setting and making cut in existing panel for fixing of MCCB as per site requirement and complete all as specified and as directed.

Please Enable Macros to View BoQ information