SPECIAL REPAIR TO BLDG NO T-31 AND T-32 OF JAK RRC, PROVN OF URINAL POINT, 04 NOS WASH BASIN, SOAK WELL AND SEPTIC TANK AND WATER SUPPLY CONNECTION AT EKLAVAYA TRG AREA OF JAK RRC AND CERTAIN MINOR WORKS UNDER AGE B/R-II OF GE (W) JABALPUR

Amount

Dismantling framed Timber Scantlings 40 Sq.cm and over in section, in any position complete all as specified and as directed.

Hacking out old broken glass [any thickness, size, quality or description] from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed.

Dismantling of Unframed Fillets, Rails, Posts, Rafters, Purlins etc under 40 Sq. cm in section complete all as specified and as directed.

Dismantling unframed mildsteel work as in wind ties, etc complete all as specified and as directed.

Dismantling of Plain or Corrugated Steel sheeting of any gauge, thickness as in roof coverings, complete all as specified and as directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets including E- Grid frame work complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete ) set in cement mortor for 150 mm internal dia of pipe complete all as specified and directed.

Demolition of Reinforced Cement Concrete [reinforcement cut as required to facilitate demolition] of any description and in any position not otherwise specifically provided for and removing rubbish to a distance not exceeding 50 M complete all as specified and as directed.

Taking down Cement Plaster any description on brick or stone walls or concrete surfaces including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Dismantling Floor, Hearth or Wall Tiling including cement mortar bedding [but not backing] and removing serviceable tiles to the stores and removing rubbish / debris of the premises complete all as specified and as directed.

Taking down chowket or frame with shutter (without taking off shutters from the frame) area not exceeding 1.5 Sqm each complete all as specified & directed.

Taking up or down steel tubing and connections for 15mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 20mm bore of pipe complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)

Dismantling RCC Water Tanks of capacity exceeding 250 liters and not exceeding 500 liters complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m depth for foundation etc or for shafts, wells cesspits manholes pier holes, for laying cables, pipes etc not exceeding 10 sqm on plan and not exceeding 1.5m depth in soft/loose soil etc complete all as specified and directed

Excavation over areas, n exc 1.5m deep & getting out in soft/loose soil complete all as specified and as directed.

Excavation over areas, exc 1.5m but n exc 3.0m deep & getting out in soft/loose soil complete all as specified and as directed.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft /loose soil complete all as specified and as directed..

Removing excavated soils n.exc. 50m and depositing where directed at a level n.exc. 1.5m above the starting point complete all as specified and as directed..

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming.

M & L for moorum/ red bajri filling under floors laid in layers not exceeding 15 cm thick, spread levelled and rammed / rolled including watering to required level and gradient complete all as specified and as directed.

M & L for hardcore of gauge not exceeding 63 mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface in broken boulder complete all as specified and as directed.

M&L for loose filling with (broken bricks) aggregate of gauge 80-150 mm as in soakage pits, sokage wells, complete all as specified and as directed.

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M & L for RCC M-25 (design mix) as in Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and as directed.

M & L for RCC M-25 (design mix) as in Columns, pillars, piers, posts and struts etc complete all as specified and as directed.

M & L for RCC M-25 (design mix) as in Slabs supported on walls, beams, columns, landings, shelves and the like complete all as specified and as directed.

M & L for RCC M-25 (design mix) as in foundations including rafts, footings, foundation beams, plinth beams, bases for columns etc complete all as specified and as directed.

M & L for providing Precast RCC 1:2:4, Type B-1 using 20mm graded stone aggregate as in landings, cover slabs [for manholes etc], chullah hoods, chajjas, water troughs, mangers, Shelves and similar articles with plain faces set in cement mortar 1:6 complete all as specified and as directed.

M & L for PCC 1:2:4, Type B-1, using 20 mm graded stone aggregate as in Bed blocks, Coping and Bed plates including weathering, slightly rounded or chamfered angles and throating and including necessary form work etc complete all as specified and directed.

M&L for 150 mm thick PCC 1:2:4, type B-2 using 40mm graded stone aggregate as in ramp complete all as specified and directed.

M & L for 75mm thick, PCC 1:3:6, Type C-1, using 20mm graded aggregate as in Plinth protection etc surface finished even and smooth with out using extra cement complete all as specified and as directed.

M & L for 25 mm thick, PCC 1:2:4, Type B-1, using 12.5mm graded aggregate as in Sub base for flooring complete all as specified and as directed.

M&L 75mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified and directed

M & L for PCC 1:4:8, Type D-2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed.

Supply only integral water proofing compound

Extra for forming fair finished drains or channels 30 cm inner girth in cement concrete using extra cement including forms moulds, mitered/ stopped ends complete all as specified.

M & L Damp proof course 40 mm thick PCC 1:2:4 type B-0 to horizontal or vertical surface complete all as specified and as directed.

M & L for cutting grooves in brick wall, 75 mm wide and 65 mm deep and shaping horizontal face of grooves with cement mortar 1:3 complete all as specified and as directed.

M & L for brick work with sub class "B" bricks, old size, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

M&L for Brick work using old size sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:4 etc complete all as specified and directed.

M&L brick work with sub class ‘ B’ bricks in one brick thick honey comb walling build in CM 1:4 all as specified.

M & L for brick work with fly ash modular bricks, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

M&L for Brick work with old size, sub class 'B' bricks, straight or curved on plan any radius in half brick thick wall built in cement mortar 1:6 complete all as specified and directed.

Cutting chases, pinning in. through brick walls and making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admix ture of pigment to match with shade of granite complete all as specified and directed..

M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

M&L for providing Machine cut Cudapph stone slab as on platform/shelf 20-25mm thick over and including 15mm thick in CM 1:4 cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Use and waste of form work to sides of pillars, posts, struts, piers, columns of any shape / cross section for fair finished surfaces of concrete complete all as specified and as directed.

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floor and beam etc. for rough finished surfaces complete all as specified and as directed.

Use and waste of form work to sides of concrete foundation, footings, bases of column, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter; for rough finished surfaces complete all as specified and as directed.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [horizontal or sloping] including fair finished surfaces complete all as specified and directed.

S & F second class hard wood, plain, solid, scantlings, clean sawn as in framed and fixed as in purlins, trusses, rafters, frame work for ceilings etc complete all as specified and directed.

Material & Labour for 35mm thick second class hard wood Factory made glazed and skelton door shutter open rebated and prepare to receive glass / gauge etc edges of framing plain chamfered or rounded edge with cut and mitred bead for securing glass or gauge etc with sash bars size of members of shutters as specified in SSR Part-I section 8, clause 8.24 (a) fixed to wooden/steel frame complete all as specified & directed.

M&L for 40 mm thick Flush shutters, solid core construction, with block board core and 5 mm thick plywood face panels on both side, commercial type on both sides covered face veneered decorative type etc.complete all as specified.

S & F solid PVC frame of size 50 mm x 47 mm made out of 5 mm single side prelaminated PVC sheet & edges will be printed to match with prelaminated sheet reinforced with MS square tube etc complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm (Style) consisting of frame made out of M.S tubes for top and bottom rails M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheets to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame complete all as specified and as directed.

S&F, Factory Made Solid PVC Moulded Door Shutters with wood free EPS 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face with particle board core, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S& F for Solid PVC moulded door frame of size 50mm x 47mm made out of 5mm Plain colour PVC sheet reinforced with M.S. tube, suppling & fixing in opening but single prelam PVC sheet used instead of Plain colour PVC sheet as per specification & drawing complete all as specified and directed.

S & F 18mm thick, PVC sheet one side prelaminated of approved texture ("Celuca Ply of Rajshree make or equivalent as approved by GE) as in Kitchen cabinet (with shelves and partitions) including necessary fittings & fixtures as per manufacturer's instructions complete all as specified and as directed.

S&F aluminium alloy anodized sliding door bolt with hasp & staples (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast aluminium alloy length of bolt 300mm complete all as specified and directed .

S & F Aluminium anodised barrel Tower Bolt of size 200 mm size of extruded section complete all as specified and as directed.

S & F in repairs Aluminium anodised Handle, Cast Type of size 125 mm, complete all as specified and as directed.

S & F in repairs Aluminium anodised Handle, Cast Type of size 150 mm, complete all as specified and as directed.

S&F 100 mm long aluminium alloy type C-21 butt hinges with galvanised ms hinge pin etc.

S&F 100 mm long aluminium alloy type C-22 butt hinges with galvanised ms hinge pin etc.

S&F continious(Piano) hinges, brass,bright finish, width of flap 30mm when open.

S & F Door spring ordinary rat tail rod pattern springs including roller and roller plate complete of mild steel 150mm long complete.

S & F in repairs of 40mm dia Brass, Bright polished, Fancy type Cupboard Knobs fixed with brass nut, screw and washer complete all as specified and as directed.

S & F in repairs Ball catches with 8 mm dia steel ball and Brass Body and Striking Plate including letting in complete all as specified and directed.

Supply only floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, over all length of cover plate 140 mm complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed by engre-in-charge.

M & L for Rolled mild steel framed work conforming to Fe 410-W (Gde E-250) quality 'A' as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete drilled for fixing of steel gate sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete all as specified.

M&L reinforcement using TMT steel bars of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

M&L reinforcement using TMT steel bars of 5mm to 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S&F factory made steel windows with side hung shutter including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F factory made steel windows with side hung shutter including box type hinges with steel handle and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S&F steel ventilator factory made with top hung shutter including hinges steel peg stay complete

Supply only expanded metal of weight per square meter not exc 4 kg complete all as specified and as directed.

S&F mild steel work as in wind ties for roofing fixed with and including suitable nuts, bolts and washers complete all as specified and directed

M&L for pressed steel door frame size 125 mm x 60 mm and 1.25 mm thick including necessary fixing lugs, hinges, lock strike platee etc., complete, as spd

M&L for pressed steel door frame size 105 mm x 60 mm and 1.25 mm thick including necessary fixing lugs, hinges, lock strike platee etc., complete, as spd

S & F MS plain black sheet 1.00mm thick in hearths covering to doors shutters, chullah hood etc with plain 40mm lap joints or welded/riveted seams including bending, turning up, mitred angles etc. as required.

S & F prepainted 0.50 mm thick gavalume aluminium zinc coating AZ 150 GI based corrugated steel coloured Sheet in profile pattern having tensile strength of 550 Mpa as in roof covering & on chajjas fixed with self tapping screws etc all as specified and directed

S & F prepainted 0.50 mm thick gavalume aluminium zinc coating AZ 150 GI based plain steel coloured Sheet in profile pattern having tensile strength of 550 Mpa as in roof serrated ridge fixed with self tapping screws etc all as specified and directed

Complete removal of existing treatment on walls including steel wire brushing and scraping etc or preparation of new platered surfaces of wall and applying 2mm thick( Avg) Birla wall care putty in two layers on wall surfaces including rubbing, levelling and preparing the surfaces for receiving further finishes as directed.

M&L for APP based polymeric membrane for unaccessable roof minimum weighing 3kg/sqm and minimum 3 mm thick reinforced with polyester non woven fabric (wt. not less than 150 gms/sqm) laid on primed surface by forced allpication complete all as specified and directed.

M&L for priming surfaces with bitumen primer

One coat of hot blown bitumen of grade 85/25 @1.2Kg/Sqm shall be applied over polymeric membrane.

M&L for 10mm thick screed bed or bedding layer in CM (1:3) mixed with water proofing compound @ 3% by weight of cement on concrete roof surface finished fair and even to maintain the proper slope of roof surface etc complete all as specified and directed.

S&F suspended false ceilingwith T- grid system of size 600 x 600mm with following specifiactions :- (i) Pre primed, self embossed, textured designer board, water resistant, termite resistant, fire resistant for insulation Calcium Silicate Boards 8mm thick (ii) GI powder coated Main Tee of size 38x24mm made out of 0.30 mm (min) thk sheet (ii) GI powder coated Cross Tee of size 24x24x0.30 mm (min) made out of 0.30 mm (min) thick sheet (iii) GI powder coated angle of size 24x24x0.30 mm (min) made out of 0.30 mm (min) thick sheet (iv) Level clip / suspension wire - 4 mm dia GI wire. (v) Soffit cleat/Rawl Plug as per manufacturers instrcutions (vi) Fixing shall be executed as per manufacturers instructions

M&L for Non Skid ceramic joint free tiles 7 to 8 mm thick ( square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed or bedding layer of mortar with CM 1:4 complete all as specified and directed.

ditto as above Item No 97 but on vertical surfaces complete

M&L for glazed ceramic tiles colour 350x250x7mm / 450x350x7mm thick as in vertical surfaces such as skirting, dado and risers to steps set and jointed in neat cement slurry and pointed in coloured cement to match over 10mm thick cement mortar 1:4 on fair faces of brick work or concrete surfaces as backing for tiles complete all as specified.

M & L for rendering 5 mm thick in Cement Mortar 1:3 on fair faces of concrete surfaces of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 15 mm th in CM 1:4 mixed with water proofing compound, on brick or concrete surface, trowelled to even and smooth finish without using extra cement, complete all as specified. ( Note :-Supply only water proofing compound shall be measured and paid separately .)

M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:6, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 for laying floor finishes etc complete all as specified and as directed.

M&L for preparing of new plastered or un-plastered wall surfaces and applying two coats of oil bound distemper over and including 2 mm wall putty on plastered surfaces, preparatory to distempering complete all as specified and directed.

M&L for 02 coats of cement base paint on old surfaces of walls incl preparation complete all as specified and as directed.

M&L for 02 coats of oil bound distemper on old surfaces of walls incl preparation complete all as specified and as directed.

M&L Preparation of new plaster surface of walls and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and as directed.

M & L for preparing newly plastered wall surfaces and applying three coats of white wash complete all as specified and as directed.

M & L for preparing newly plastered ceiling surfaces and applying two coats of white wash complete all as specified and as directed.

S & F in repair 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

S & F 3 mm thick figured glass pin head type and glazing with oil putty/wooden beads in squares n exc 0.5 Sqm in each pane etc complete all as specified and directed.

M & L for two coats of synthetic enamel paint on old wooden surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M&L applying two coats of synthetic enamel paint over a coat of pink primer including preparation of new wooden surfaces exc 10 cm width or girth, complete all as specified and directed.

M & L for two coats of synthetic enamel paint over one coat of red oxide primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for two coats of synthetic enamel paint new / old steel surfaces not exceeding 10cm width or girth including preparation of surfaces complete all as specified and as directed.

Supply & laying of CPVC pipes 16 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors complete all as specified and as directed.

Supply & laying of CPVC pipes 20 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors complete all as specified and as directed.

Supply & laying of CPVC pipes 25 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors complete all as specified and as directed.

M&L for 32 mm bore low density polythelene pipes (LDPE) with fittings of pressure rating 6 Kgf / Sqcm fixed to walls or in floors etc complete all as specified and directed.

M&L for 40 mm bore low density polythelene pipes (LDPE) with fittings of pressure rating 6 Kgf / Sqcm fixed to walls or in floors etc complete all as specified and directed.

S&F rotational molded polyethylene water storage tanks (cylindrical vertical with closed top) capacity 500 Ltr hoisted and fixed in position all as specified and directed by Engr-in-charge.

S&F Rotational moulded polyethylene water storage tanks in white colour tripple layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I of 1000 Ltr capacity all as spd.

S & F in repairs Ball Valves, 20 mm Bore, high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe [Minimum Weight 20mm - 210 Grams] etc complete all as specified and as directed.

S&F in repairs stainless steel kitchen sink with drainage board of overall size 915x460mm and bowl size 410x330x160mm with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe complete all as directed.

S & F Stain less steel plate rack including fixing overall size 900x900mm depth not less than 25 cm and thickness not lessthan 1mm complete all as specified and as directed

S & F for Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed complete all as specified .

S & F for Soap dish, any type, fixed to plugs with chromium plated brass screws fixed complete all as specified and directed.

Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified .

Towel Rail 600mm long of PTMT/SS fixed with and including Chromium plated brass screws and wooden/plastic cleats .(Minimum weight 190gms) fixed complete.

S&F , in repair, PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F vitreous china squatting pan white orissa pattern size 580 x 440mm with integral foot rests (excludig flushing cistern & flush pipe) with cast iron trap portion to match with the existing surface of floor all as specified and directed by Engr-in-charge.

S&F vitreous china wash basin white flat back size 550 x 400mm excluding taps, waste, chain & plug and porcelain stopper but including brackets, PVC connections 450 mm long all as specified and directed by Engr-in-charge.

S & F for Wash basins, Vitreous China (flat back type) any size, including cutting for and pinning in ends of brackets or erecting stand etc. complete with all accessory.Make:- Parrayware/ Hind ware /CERA/Prayag

S&F vitreous china full stall urinals,white, complete including providing and fixing plugs, securing urinals to plugs with and including 60mm long brass screws, fixing flush pipe, grating and union for discharge pipe.

Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60 gms) complete all as specified and as directed..

S&F PVC low level flushing cistern of capacity 10 litres complete with siphon handle, lever, float valve and PVC bend including connecting to ITWC/ ETWC, PVC connection 450 mm long and fixing on wall bracket complete all as specified and directed by Engr-in-charge.

S&F chromium plated shower rose fancy type fixed to 15mm bore pipe all as specified and directed by Engr-in-charge.

S & F in repairs, Bib Taps, cast copper alloy, 15 mm dia, Chromium Plated with crutch or butterfly handle, screwed down for iron pipe etc complete all as specified and as directed.

S & F in repairs, Stop Valves, 15 mm dia, cast copper alloy with capstan head, Chromium Plated, Fancy Type, screwed down high pressure with crutch or butterfly handle with long shank and cup [concealed type] for iron pipe etc complete all as specified and as directed.

S & F in repairs, Stop Valves, 20 mm dia, cast copper alloy with capstan head, Chromium Plated, Fancy Type, screwed down high pressure with crutch or butterfly handle with long shank and cup [concealed type] for iron pipe etc complete all as specified and as directed.

S & F in repairs, Gun Metal Globe or Gate Valve, 20 mm bore with iron wheel head, screwed both ends for iron pipe, confirming to IS, ISI Marked complete all specified and as directed.

S & F in repairs, Gun Metal Globe or Gate Valve, 25 mm bore with iron wheel head, screwed both ends for iron pipe, confirming to IS, ISI Marked complete all specified and as directed.

S & F in repairs PTMT Graiting Doom, 100 mm dia [Minimum weight 25 Grams] without waste hole or with waste hole to insert waste pipe complete all as specified and directed.

S & F for Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats(Minimumweight300gms) fixed complete all as specified.

S&F 15mm bore pillar taps cast copper alloy fancy type chromium plated screwed down high pressure with or without lattered HOT or COLD with long screwed shanks and fly nuts screwed for iron pipes, att as directed Engr-in-Charge.

M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 150 mm bore of pipe with cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate complete all as specified and directed.

M&L salt Glazed stone ware drain pipe 150 mm bore grade 'A' laid in trenches and jointed and testing complete all as specified & directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel [½ round or ¾ section] in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required for 100 mm dia of pipe complete all as specified and as directed

S&F, PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints, laid in trenches or in walls complete all as specified and directed.

S&F, in repair PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, laid in trenches or in walls complete all as specified and directed.

S&F PVC (SWR) bends ISI marked any radius of 110 mm bore with access door complete all as specified and directed.

S&F PVC (SWR) bends ISI marked any radius of 75 mm bore with access door complete all as specified and directed.

S & F 110 mm bore PVC [SWR] Junction Single [Single "T"] equal or unequal with access door complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Vent Cowl complete all as specified and as directed.

S & F 75mm bore PVC [SWR] Floor Trap with grating including jointing with solvent cement complete all as specified and as directed.

S & F in repairs 32mm dia PVC Waste Pipe fixed to Wash Hand Basin or Sink complete all as specified and directed.

S & F solid wall UPVC socketed drain pipes, conforming to IS 15328 -2003 with 160 mm bore dia including laying and jointing complete all as specified and as directed ( Make : Supeme , Nu Drain or equavalent )

Taking down carefully any type of old unserviceable point wiring copper or aluminium conductor (light, fan, socket, bell or power) point complete with fittings with PVC conduit surface / concealed or wooden battens including sunken cast iron / pressed steel terminal boxes etc and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces complete all as specified & directed by Engineer-in-Charge.

Taking down carefully main switch and distribution board any make and size.

Taking down the ceiling fan in situ and refixing after servicing, repairing and painting to ceiling fan including scratching old paint and preparation of surface for painting with one coat of white/grey enameled paint complete all as specified and directed.

Taking down carefully old unserviceable any type sub main wiring with wooden batten/ PVC surface conduit of any size and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces completa all as specified and directed by Engineer in charge.

M&L for Sub Main Wiring two single core PVC insulated cable of size 4.0 Sqmm multistranded copper conductor FRLS 1100 volts two run drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 25mm dia with all conduit fitting,fixing accessories and one run of 4.0 Sqmm multistrand copper conductor cable as continuous earth wire complete all as specified and directed by Engineer in charge Note :-Two Nos of 4.0 Sqmm Wire and one No of 4.0 Sqmm Earth wire in One RM length Measured as one unit length.

M/L for Sub Main Wiring two single core PVC insulated cable of size 6.0 Sqmm multistranded copper conductor two run drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 25mm dia with all conduit fitting,fixing accessories and one run of 6.0 Sqmm multistrand copper conductor cable as continuous earth wire complete all as specified and directed by Engineer in charge Note :-Two Nos of 6.0 Sqmm Wire and one No of 6.0 Sqmm Earth wire in One RM length Measured as one unit length.

M&L for Point wiring with PVC FRLSH insulated 1.5 sq mm multi stranded copper conductor cable 1100 volts grade drawn into and including concealed/open PVC conduit not less than 20mm (ISI marked) including all fitting and fixing accessories including sunk in cast iron/pressed steel terminal boxes duly painted with two coats of antirorrrosive paint outside and two coats of aluminium paint inside, 2.8mm thick hylam brand laminated white bakelite sheet cover for mounting of switches, sockets, fan regulators etc and PVC insulated 1.5 Sqmm multistranded copper conductor cable as earth wire and making good the disturbed surfaces to match with the existing surfaces complete all as specified and directed by Engineer in charge.

(a) One light point/ Bell point controlled by one switch.

(b) One fan point/ exhaust fan controlled by one switch.

(c) One socket point controlled by one switch on same board.

(d) One socket point controlled by one switch on Independent board.

Description all as per item No 167 here in befor but with 1100 volts grade copper standard conductor cable FRLSH of size 2.5 Sqmm with 2.5 Sqmm solid copper conductor PVC for 3 pin switch socket outlet15 Amp independent board complete all as specified and directed by Engineer in charge .

S & F in repair for bell ding dong AC 230 volts single pole one way complete all as specified and directed by Engineer in charge.

M&L for fan regulator Step type of polycarbonate complete all as specified and directed by Engineer in charge.Make: anchor/plaza/leader

M&L for Switch piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and directed by Engineer in charge.

M&L for Socket outlet 3 pin, 5 Amps and AC 230 volts flush type complete all as specified and directed by Engineer in charge

M&L for switch socket combination 3 pin 5 and 16 Amps AC 230 volts flush type complete all as specified and directed by Engineer in charge Make: anchor/plaza/leader

M&L for Ceiling rose surface bakelite 65 mm x50 mm three terminal AC 230 volts flush type complete all as specified and directed by Engineer in charge

S & F in repair lamp holder PVC Polycarbonate type body, with back plate for batten fitting icluding 9 watt led lamp complete all as specified and as directed by Engineer in charge.

S & F Exhaust fan heavy duty size sweep PVC 230 mm sweep, 230 v, 50 Hz , complete with louvers including making holes and making good the disturbed surface complete all as specified and directed by Engineer in-charge.

S & F Exhaust fan heavy duty size sweep 300 mm sweep, 230 v, 50 Hz , complete with louvers including making holes and making good the disturbed surface complete all as specified and directed by Engineer in-charge.

Supply and fixing in replacement of decorative wall light fitting made up of Polycarbonate ,Cylindrical shape ,with LED lamp 9 Watt complete with fixing arrangements on wall all as specified and directed. Make: CITY 1 OF HAVELLS or equivalent in Bajaj/Philips

S & F in repair of LED Decorative /mirror light fitting aluminium housing 9/10 watt along with fixture Surface mounted suitable for indoor aplication , connector block, etc . Complete with all accessories internally pre-wired and including round wood block, connecting up with three core flexible flexible copper conductor cable suitable size complete all as specified and directed by Engineer in charge.Make- Havells LUMILINEPLUSSBS10WLED865SPCSS or equivalent in PHILIPS ,BAJAJ

S & F in repair Bulk head endura LED light fitting complete with10 watt LED and making necessary electric connection to ceiling rose with copper conductor of suiyable size & length complete all as specified & directed. Make :Havells Cat Part No. HEXAFT10WLED857SSYMBOPC or Equivalent make Philips / BAJAJ

S & F in repair Sheet metal enclosure DBs Tripple Pole and Neutral 4- way with 200 Amps rated bus bar 415 volts single pole and neutral complete double door complete all as specified and directed by Engineer in charge Make- Legrand cat part No.- 607715 , L&T, ABB.

Supply and fixing in replacement Sheet metal enclosure DBs Single Pole and Neutral 8 way with 200 Amps rated bus bar 240 volts single pole and neutral complete double door complete all as specified and directed by Engineer in charge Make- Legrand , Siements, GE

Supply and fixing MCB single pole and neutral 240 volts 40 Amps, B Series complete all as specified and directed by Engineer in chargeMake- Legrand , Siements, GE

Supply and fixing in replacement MCB/ Isolators single pole 240 volts upto 40 Amps, B Series complete all as specified and directed by Engineer in charge Make- Legrand , Siements, GE

Supply & Fixing in repair single pole and netural sheet metal enclosure with a two pin and earth plug and socket complete with 01 number single pole MCB 20 Amps complete all as specified & directed.Make: Legrand cat no :5078 11 or eq in SEIMENS /GE

Supply and fixing in replament MCB single pole 240 volts 6 Amp to 40 Amps, B series complete all as specified and directed by Engineer in charge Make : Legrand Cat No DX3SP, 408587, 408590, 408592, 408593, 408594, 408595/ Siemens Cat No 5SL41067RC, 5SL41107RC, 5SL41207RC, 5SL41257RC, 5SL4132RC/GE

Supply & fix in replacement of LED Security Light Luminaire 25 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens type,GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat , nuts and bolts and painting with aluminium paint. complete all as specified and as directed.Make:Havells cat part no: LHDAUU7PA7J025 or equivalent in philips or Wipro

Supply & fix in replacement of LED Security Light Luminaire 35 watt with 2500 or more lumen warm white, surge protection device upto 4KV, IP65 or more, IK07 or more, potted driver suitable for 180 to 270 V, 50 Hz, light engine driver base.pole adapter, powder coated pressure die cast aluminium with heat resistant toughened glass with lens type,GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat , nuts and bolts and painting with aluminium paint. complete all as specified and as directed.Make: Philips cat part no: BRP029 LED25/WW MRPSU GR DX or havells cat part no. ENDURASUNDOWNSL35WLED765PASYBOPCIHD or equivalent in wipro/GE

Supply and fixing in replacement MCB TPN 415 volts 63 Amps, C Series complete all as specified and directed by Engineer in charge.Make- Legrand /Seimens/GE

Supply, fixing, connecting and testing of Automatic Street light switch using infrared Sensor based Nature Switch for automatic switching of street lights, Nature switch operation should be based on Natural light lux level. Required illumination level for switching on is < 30 lux and for switching off > 10 lux. The sensor should also have part night operation facility for 4 - 12 hours. The sensor alongwith suitable power contactor, incoming-outgoing MCBs should be enclosed in a pole/wall moutaed enclosure made out of Rust proof, electric shock proof, termite proof and FR grade SMC junction box conforming to IP-54, The circuit should be suitable enough to take 8 kw single phase load with contactor 63 Amps conforming to IEC-60947-4-1/IS-13947-4-1 & incoming and outgoing MCBs of rating 63 Amps conforming to IEC-60898/IS-8828 and circuit wiring of minimum 16sqmm coper conductor wire in and including providing of 50x6mm flat iron clamp, necessary nuts and bolts complete incl taking down of existing arrangement all as specified and directed by the Engr-in-charge. Make of nature switch - Model No Swadeep-02EC8kw1P of Kakatiya Energy System or equivalent make of Bajaj/Healer, Make for Contactor- BCH/L&T/Schneider, Make of MCBs- Hager/Schneider/L&T/C&S, Enclouser - Sintax or equivalent

Supply, fixing, connecting and testing of Automatic Street light switch using infrared Sensor based Nature Switch for automatic switching of street lights, Nature switch operation should be based on Natural light lux level. Required illumination level for switching on is < 30 lux and for switching off > 10 lux. The sensor should also have part night operation facility for 4 - 12 hours. The sensor alongwith suitable power contactor, incoming-outgoing MCBs should be enclosed in a pole/wall moutaed enclosure made out of Rust proof, electric shock proof, termite proof and FR grade SMC junction box conforming to IP-54, The circuit should be suitable enough to take 8 kw Three phase load with contactor 25 Amps conforming to IEC-60947-4-1/IS-13947-4-1 & incoming and outgoing MCBs of rating 32 Amps conforming to IEC-60898/IS-8828 and circuit wiring of minimum 10sqmm copper conductor wire in and including providing of 50x6mm flat iron clamp, necessary nuts and bolts, complete all as specified and directed by the Engr-in-charge. Make of nature switch - Model No Swadeep-02EC8kw3P of Kakatiya Energy System or equivalent make of Bajaj/Healer, Make for Contactor- BCH/L&T/Schneider, Make of MCBs- Hager/Schn

S & F in repair Smart bright Batten Series, LED luminaire using LEDs 20 watt 110 LM/watt with diffuser which ensures uniform distribution and comfort batten series features latest LEDs and delivers consistent light output, stable color start Extruded Aluminum housing, Energy efficient, Flicker free start Inbuilt driver unit Suitable for wall and ceiling mounting using brackets complete all as specified and as directed.

S & F in repair Smart bright Batten Series, LED luminaire using LEDs 22 watt 110 LM/watt with diffuser which ensures uniform distribution and comfort batten series features latest LEDs and delivers consistent light output, stable color start Extruded Aluminum housing, Energy efficient, Flicker free start Inbuilt driver unit Suitable for wall and ceiling mounting using brackets complete all as specified and as directed.Make : Philips Cat part BN 021 LED 22S 6500 PSU GR SI or equivalent.

Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 4 mm dia by means of nut, bolts, check nuts and washers of galvanised iron or steel complete all as specified and directed including testing on completion including the material and labour of the following : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) Reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 15 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing.

S & F in repair for bell push piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and directed by Engineer in charge.

Supply, installation, testing & commissioning of 1 Phase, 2 Wire, Smart Prepaid Energy Meters, BIS 16444 Marked in existing Meter Board / Floor Panels with Pre Payment Shock Proof capacitive touch Keypad (Similar as IOS and android phone technology), Bluetooth, based Digital having current range 05-60 Amp, 240 V, accuracy class 1.0 along with inbuilt load control switch, containing provision for TOD & RTC, inbuilt feature sense for data transfer (wireless, without DCU, USB, Pen drive) no other extra equipment required for data transfer, meter itself capable for data transfer) capable to define 4 tariff slabs, happy hour & holiday definition, when user go outside of the home, user can punch recharge token on meter keypad and manually and automatic via mobile app. Meter should support the following data’s :- 30 minutes instantaneous data for voltage, current, power factor, power, cumulative energy and frequency, 30 load survey data for energy, monthly billing survey for Cumulative Energy and Max Demand. Meter should have connect / disconnect remotely, functionality operable for prepaid/ post-paid billing software. The meter should support communication protocol NB IOT/ DLMS with the software all as specified and directed. That the manufacturer or their service provider shall furnish 10 (Ten) years replacement guarantee for prepaid meters installed under this contract except demage from water and fire. OEM will be responsible for connectivity and smooth functioning with MES server without any hindrance. including all acceseries if required for imstallation of meter for its smooth and user friendly operation all as per required and directed by Engineer in charge.

Supply , laying and testing cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cab les ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 2.0 core 16 Sqmm complete all as specified and directed by Engineer in charge Make- Polycare,Havals

Supply , laying and testing cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cab les ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 3.5 core 35 Sqmm complete all as specified and directed by Engineer in charge Make- Polycab/KEI/Havells

Supply, laying or fixing or passing through pipe commissioning and testing of PVC XLPE insulated, armoured heavy duty, electric cable with aluminium conductor, 1100 volts grade, multi -stranded of SIZE 16SQMM 4 CORE including suitable size lugs all as specified and directed. Make: Polycab/KEI/Havells. Note:- Excavation & earth work, sand cushioning, bricks protection & GI pipe where required shall be measured & paid separately under relevant items.

Supply, laying or fixing or passing through pipe commissioning and testing of PVC XLPE insulated, armoured heavy duty, electric cable with aluminium conductor, 1100 volts grade, multi -stranded of SIZE 25SQMM 4 CORE including suitable size lugs including taking out /dismantling of existing cable. Make: Polycab/KEI/Havells. Note:- Excavation & earth work, sand cushioning, bricks protection & GI pipe where required shall be measured & paid separately under relevant items.

M & L for dry river sand cushioning over and around the cable for cable protection in trenches, leveled and punned down complete all as specified and as directed. Note: The punned down thickness shall be measured for payment.

M&L for Demolition of road/path /concrete in ground floors and pavings PCC 1:2:4 type B-1 n exc 15 cm thickness (below or above ground level) .complete all as specified and as directed.

Supply and lay bricks sub class 'B' laid dry abutting each other with gap between adjacent slab not exc 10mm over UG cabel as in cable protection all as directed.

M&L for GI Tubes,of size 40 mm dia light grade, galvanised, with all fitting , laid in trenches for protection of cable in road /drain crossing complete all as specified and as directed.

Sachdeva Enterprises

chandra builders

J.P ENTERPRISES

C L BHATIA