SPECIAL REPAIR TO OTM ACCN BLDG NO T-52, T-60, T-62, T-72 AND T-73 AT AMRITSAR CANTT UNDER GE AMRITSAR

Amount

Taking down chowkats or frames with shutter’s (without taking off shutter’s from frame) not exc 1.50 sqm each all as specified and directed.

All as per ser item No 1 here-in-before but exc 1.50 Sqm and not exc 4.00 Sqm each complete all as specified and as directed.

S&F mild steel grill, guard bars welded and fixed in steel frame etc complete all as specified and directed.

Supplying and fixing MS framed works as in door frame, gates of angle or other section with gusset plates, rails, braces etc , drilled for fixing of steel sheeting including drilling or fixing welding be prepared for hanging or sliding with and either hooks and hinges fixing complete all as specified conforming to Fe290 Gde E-165, complete all as specified.

Material and Labour for Box type steel window made of ERW tube P- section of size 60 mm x 25 mm double frame, comprises glazed and gauged skelton shutter of ERW tube P-Section size 50mm x 20mm with one/two Nos openable leaf consisting of two Nos Sashbar of T-section 20 x 3 mm welded to frame with one No verticle mullion of ERW box type T Section of size 60mm x 25mm and FI 2mm thick welded/screwed to frame for fixing of glass including fittings and fixture like as Handle, Tower Bolt, Stopper, Cleat, Pintal hinges, holdfast etc as given below all as shown on drg No CEJZ/TD-1020/08 Sh 1/3 to 3/3 dt 01 May 2008 complete including cutting holes, making good dismentled portion in PCC 1:2:4 type B-1, all as specified and directed. (a) Hold fast 150mm long of 12mm x 3mm MS flat - 4 Nos per Window. (b) Handle of Z section 20mm x 25mm, 100mm long- 01 No per leaf. (c) MS tower bolt 150mm long - 02 Nos/leaf. (d) Z Section stopper 20mm x 25mm, 100mm long - 01 No per leaf. (e) Cleat 55mm long of hollow square 15mmx12mm - 02 Nos per leaf. Note 1 :- Wire guage, Guard bar, sheet glass and painting shall be measured and paid sperately. 2. Mode of measurement for this item shall be for window portion only excluding ventilator portion where ever shown in drawing.

Dismantling of Asbestos Cement Corrugated or semi corrugated sheets in Roof Covering of any gauge and Thickness all as specified and directed.

Dismantling timber scantling 40 Sqcm and over in section any position as in framed works complete all as specified and as directed.

Distmantling of ceiling boards (fibre, pulp, insulation etc) or insulation bords/ slab/blankets, any thickness, including cover fillets complete all as specified and directed.

S&F GI frame work for seamless ceiling with grid size 605x605mm comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre complete all as specified and as directed.

S&F Gypsum Board 12mm thick in ceiling fixed with screw and applying two coats of oil bound disstemper over a coat of primer as per manufacturers instructions all as specified and directed by Engr-in-Charge.

S&F prepainted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength 550 MPA as in roof covering in roof covering with self tapping screws / L type or J type hook as specified Make-TATA/EVEREST and all other Equivalent makes specified in appendix 'B'

S&F pre-painted galvatume aluminium zinc coating GI based plain sheet steel sheet0.50 mm thick as in ridges of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F steel work in tubular trusses incl special shaped washer etc., complete using ERW or incl butt welded tubes conforming to I.S. 1161-1998 grade St-240 all as specified and directed by Engr-in-Charge.

Taking down cement plaster from wall’s/ceiling including raking out joints hacking for key scrubbing down with water complete all as specified and directed by Engr-in-Charge.

M&L for 15mm rendering in cement mortar (1:6) on brick/concrete surfaces finished the surface even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L for 15mm rendering in cement mortar (1:4) on brick/concrete surfaces finished the surface even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L preparation of newly plastered surfaces of wall and applying two coats of distemper oil emulsion white or tint with priming plastered and other surfaces with chalk whiting on plastered surface complete all as specified.

M&L for applying two coat of oil bound distemper above a coat of primer incl. complete removal of old treatment or on newly plastered surfaces complete all as specified and directed by Engr-in-Charge.

M&L preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of whtie wash complete all as specified and directed by Engr-in-Charge.

M&L complete removal of existing treatment and applying two coat of cement base paint over a coat of white wash complete all as specified and directed by Engr-in-Charge.

Demolition of PCC as in ground floor & Paving nxc 15cm (Below or above) ground level including disposal of rubbish to a distance nxc 500mtr where directed complete all as specified and directed by Engr-in-Charge.

M&L 75 mm thick cement concrete type C-2, 1:3:6 (using 40 mm graded crushed stone aggregate), as in sub base of floors complete all as specified and directed by Engr-in-Charge.

S&F machine pressed precast concrete interlocking paver block any shape and size with grey cement and no pigment conforming to IS 15658-2006 of 60 mm thickness M-35 Grade and including 25mm thick sand chusion complete all as specified.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in 50mm thick plinths protection and as in path complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 12.5 mm graded stone aggregate in bed blocks for hold fast etc complete all as specified and directed

M&L for two coats of synthetic enamel paint on steel surface exc 10 cm width or girth on one coat of primer (Red oxide Zinc crown) incl preparation of old/new surfaces complete all as specified and directed by Engr-in-Charge.

M&L for one coats of synthetic enamel paint on Old steel surface exc 10 cm width or girth incl preparation of old/new surfaces complete all as specified and directed by Engr-in-Charge.

M & L for two coats of synthetic enamel paint over one coat of primer (Pink Primer) on wooden surfaces exceeding 10cm width or girth including preparation of surface complete all as specified and directed by Engr-in-Charge.

S&F 30 mm thick flush shutter, soild core construction, with block board core and pluwood face panel commercial type on both sides complete all as specified and directed by Engr-in-Charge.

S&F 35 mm thick flush shutter, soild core construction, with block board core and pluwood face panel commercial type on both sides complete all as specified and directed by Engr-in-Charge.

S & F 35mm thick 2nd class hard wood glazed and skeleton shutter’s open rebated prepare to receive glass gauge etc edges of framing plain chamfered or rounded fitted with Cut and mitered bead’s for securing glass gauge etc size of marker of shutters as per SSR Part-I Section-8 clause 8.2 (a) complete all as specified and directed by Engr-in-Charge.

Supplying and fixing mild steel ordinary rat tail rod pattern spring 300mm size , including roller and roller plate , complete all as specified and directed.

S & F butt hinges 100 mm size medium weight cold rolled mild steel complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with oil putty or fixed with beads complete all as specified and directed by Engr-in-Charge.

S & F in repair stainless steel wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples.

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed by Engr-in-Charge.

Supplying and fixing 3mm thick ordinary sheet glass and glazing with oil putty or fixed with wooden beading, in squares not exc 0.50 Sqm in each panes complete all as specified.

S&f 250mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed by Engr-in-Charge.

S&F 200 mm long aluminium anodised barrel tower bolts and extrude section and fixed complete all as specified and directed by Engr-in-Charge.

S&F 150 mm long extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed by Engr-in-Charge.

S&F 150 mm long aluminium anodised barrel tower bolts and extrude section and fixed complete all as specified and directed by Engr-in-Charge.

S&F 100 mm long extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed by Engr-in-Charge.

Demolition of brick work built in cement mortar complete all as specified and directed.

M&L for brick work using sub class ‘B’ bricks, straight or corved on plan exc. 6 mean radius in CM 1:6 complete all as specified and directed by Engr-in-Charge.

Complete all as per srl item No. 44 here in before but "except brick".

Dismantling floor,hearth or wall tiling inlcuding cement mortar bedding ( but not backing ) removing to serviceable tiles to store and rubbish of the premises etc complete all as specifeid.

Roughning surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc and Brushing neat cement slurry with 3.0 Kg of cement per sqm. Complete all as specified

S&F coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement or coloured cement to match over 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

S&F coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in verticle surface. set and jointed in neat cement slurry and pointed in white cement or coloured cement to match over 10 mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engr-in-Charge.

M&L machine cut kota stone slab flooring 20-25 mm thick over 15mm thick cement screed base of cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade to the slab incl rubbing and polishing complete all as specified and directed by Engr-in-Charge.

M&L machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid cement screed and jointed with grey cement slurry mixed with pigment to match the shade to the slab incl rubbing and polishingover 10mm thick cement screed base of cement mortar 1:4, complete all as specified and directed by Engr-in-Charge.

Excavation in trenches not exceeding 1.5m in width and not exceeding 1.5m deep, in soft/loose soil for foundation, laying of pipes, cables, wells, cesspits, manhole, pier holes & getting out complete all as specified and directed.

Returning, filling in trenches including spreading, leveling, watering and well ramming in layers not exc 25cm thick complete all as specified and directed.

Removing excavated material to distance not exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

M&L for road cutting including excavation and getting out ,returning filling in spreading and well ramming in layers soling with broker bolders and quarring stones,inter stices filling,7.5 cm thick (compacted thickness) WBM with coarse aggregate retrieved from road cutting consolidated to required gradient and camber including applying evenly a priming tack coat with bituminous primer and making surface even and getting out surplus soil complete all as specified and as directed.

Taking down old unserviceable point wiring from existing conduit / batten type (light, fan, socket or power point) complete such as switches, ceiling rose, pendent holder, regulator and socket etc and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing complete all as specified and directed.

M&L for point wiring for one light/fan/bell/buzzer point controlled by one 1-way switch complete with 1.5 Sq mm (nominal area) FRLS, PVC insulated, un-sheathed and stranded copper conductor cable ISI marked, in and including PVC concealed conduit ISI marked of size 20 mm dia and 1.5 mm wall thickness and PVC conduit fittings such as tees, bends, elbow, reducers including cutting, chasing, making good in CM 1:3 and 1.5 Sq mm (nominal area) FRLS, PVC insulated, un-sheathed and stranded copper conductor cable ISI marked as earth wire, connecting to common earth dolly with thimble, including pressed steel powder coated MS sunken box of suitable size, covered with & including 3 mm thick bakelite, laminated hylem sheet top cover and making good surface as original by plastering and white / colour wash / distemper etc complete all as specified. Note: i) The cost of MS sunken box and bakelite sheet is included in the unit quoted rate. ii) The wiring shall be done in proper colour coding using red, yellow and blue for neutral and green for earth leads.

All as per Srl Item No 57.00 here-in- before but for one 3 pin socket outlet point 5 amps on the same board. Note : The wiring shall be done in proper colour coding using red, yellow and blue for neutral and green for earth leads.

All as per Srl Item No 57.00 here-in-before but for one 3 pin socket outet point 5 amps on independent board. Note : The wiring shall be done in proper colour coding using red, yellow and blue for neutral and green for earth leads.

All as per Srl Item No 57.00 here-in-before but with 2.5 Sq mm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire for power point on independent board. Note : The wiring shall be done in proper colour coding using red, yellow and blue for neutral and green for earth leads.

S&F switch piano flush type 5 Amp AC single pole one way, 230 volts, complete all as specified.

S&F socket outlet 5 Amps, 2/3 pin combined, 230 volts, AC complete all as specified.

S&F switch piano 15 Amps, 230 volts, 2 in 1 3 pin flush type, AC complete all as specified.

S&F socket 15 Amps, 2/3 pin combined, multipin, 230 volts, AC complete all as specified.

S&F ceiling rose surface bakelite 65 x 50mm three terminals complete all as specified and directed.

S&F lamp holder insulated body with back plate batten/angle type complete all as specified and directed.

S&F MCCB Incomer distribution board double door vertical type made out of CRCA MS sheet surface with insulated material like polyester or with epoxy powder coating surface mounting TPN 4 way, 415 volts with copper bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCCB and IP 43 - IK 09 protection with and incl 100 amp 36 kA 4 pole MCCB with thermal - magnetic setting and Icu = Ics = 100% complete all as specified. (Note : The cost of removing old wooden box and making good of surface as original by brick work, plastering, whitewash/colour/distemper etc is included in quated rate)

Supply and fixing in repair new generation energy saving and environmental friedly long life versalite 10 watt LED,6000K bulk head luminaire including builtup LED with opal diffuser light fitting complete all as specied and directed Make - Havells,Philips,Bajaj or Equivalent cat part in makes specified in appendix 'B'

M&L for sub main wiring consisting two single core PVC insulated cable with stranded copper conductor, size 6 Sqmm, copper earth wire 6 Sqmm, drawn in and including concealed non metalic PVC conduit, 2 mm thick, 25 mm dia (external) inclusive of MS junction / terminal boxes and all fittings and accessories including taking down old unservicable sub main wiring complete all as specified. Note:- Two run of cable 6 Sqmm and one run of 6 Sqmm earth wire including PVC conduit shall be measured as 'One Unit'.

S&F, in replacement, security light IP 66 with high power LED, 36 watt, energy saving, environment friendly, including bracket made out of GI pipe medium grade 40 mm bore 1.5 mtr long, made to shape, fixed with MS clamps of MS flat 40x6mm, nuts, bolts and washer and making connection with and provision of electric cable complete all as specified and directed.

Supply, laying and testing LT Cable of XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, heavy duty with aluminium conductor, 1100 volts grade, 16 Sqmm 4 core, including thimbles / lugs / cable gland etc, laid in duct / trench / along pole etc complete all as specified.

M&L for sand cushioning with a layer of fine sand 8 cm thick before laying the cable and 15 cm after laying the cable in trenches to cover under ground cable complete all as specified and directed. Note :-Punned down thickness of sand shall be considered for measurement)

Supply and lay, bricks, common burnt, sub class 'B', old size, for protection of cable, laid in trenches over cable, length of brick perpendicular to directon of cable, complete all as specified and directed.

S&F GI pipe 50mm bore medium grade for cable protection, fixed to poles, under road, along wall inculding necessary MS clamps complete all as specified and directed.

S&F, in stepped type electronic fan regulator, flush type, 100W, 230 volts, AC complete all as specified.

Supply and fixing, wall/ceiling mounted, LED 18 Watt PC Diffuser tube light fitting complete with all accessories, 1x18 Watt LED tube rod and making necessary connection with PVC insulated copper twin core 23/0.0076 twisted wire complete all as specified and directed.

Material and labour for sub main wiring consisting two single core PVC insulated cable with stranded copper conductor, size 4 Sqmm, copper earth wire 4 Sqmm, drawn in and including concealed non metalic PVC conduit, 2 mm thick, 25 mm dia (external) inclusive of MS junction / terminal boxes and all fittings and accessories including 1 taking down old unservicable sub main wiring complete all as specified. Note:- Two run of cable 4 Sqmm and one run of 4 Sqmm earth wire including 01 run of PVC conduit shall be measured as 'One Unit'.

Supply and fixing Distribution Board, double door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, SPN 12 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc and making all necessary connections including taking down old unservicable boards complete all as specified and directed.

S&F in repair MCB B Curve type, 10 KA, 32 to 63 Amp, double Pole with over load and short circuit protection complete all as specified and directed.

S&F in repair MCB B Curve type, 10 KA, 6 to 32 Amp, Single Pole with neutral, with over load and short circuit protection complete all as specified and directed.

S&F in repair MCB B Curve type, 10 KA, 40 to 63 Amp, Single Pole with neutral, with over load and short circuit protection complete all as specified and directed.

Material and Labour for earthing complete with GI earth plate electrode 600mmx600mm, 6mm thick, burried in ground vertically to a depth not less than 2.25 meters below ground level with top edge of the earth plate to a depth not lesss than 1.5 meter below the ground level, earth plate surrounded by 15cm thick layers of common salt and charcoal dust starting from ground below 15 cm of earth plate and up to 15 cm above the same. GI plate connected with galvanised iron earth lead wire of 4mm dia by means of GI nuts, bolts and washers. wire laid in 15mm dia light grade GI pipe as protection from top of the plate up to test point (cost of protection pipe up to 7.5 meters from earth electrode will be included in the rates quoted by the contractor) with following:- (a) Test point of GI strip of size 25mmx4mm. (b) Watering pipe of GI pipe light grade 20mm bore from top of the earth electrode up to MS funnel with wire mesh embeded in floor of PCC earth pit. (GI Funnel should properly tightned on GI watering pipe and embeded in PCC floor of earth pit with open top suitable for watering of earth pits) (c) PCC earth pit 30x30x30cm constructed in PCC 1:2:4 type B1 exposed surfaces smoothly finished with 15mm thick cement mortar 1:6 plaster including RCC pit cover 25mm thick with 2 Nos MS handles of 12mm dia suitable for carrying of pit cover (d) Angle iron frame made of 40x40x4 mm angle iron PCC pit for holding the pit cover. Note:- The cost of excavation & earth work shall be included in the quoted rates.

M/s Vijay Construction Co.

B.J.CONSTRUCTION CO

GEE EMM ASSOCIATES

Sai Construction Co.

M/s MAHAJAN CONSTRUCTION CO.