ADDN/ATLN AND SPECIAL REPAIR TO NORTH, SOUTH WATCH TOWER AND P-134 BUILDING AT TS MAHUL UNDER GE (NW) MANKHURD

Amount

Dismantling completely existing roof treatment (excluding cement screed bed ) including loosened cement plaster and exposing the top surface of RCC slab and making good the same in CM 1:4 and removing rubbish, etc to a distance exceeding 500m and not exceeding 1.0km etc complete all as specified and directed

M & L for APP modified roof treatment over existing roof slab etc to be executed through approved authorised applicator of the membrane manufacturer with the following specifications complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying APP modified water proofing membrane reinforced with non woven polyester fibre weight not less than 160gm/Sqcm using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Applying one coat of solar reflective bituminous aluminium paint @ 0.10 Kg/Sqm over APP membrane (d) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.50 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sqcm (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption - Not more than 1% on mass within 24 hours. (ix) Cold flexibility - Minimum (-) 20C. (x) Dimentional stability % change = Maximum 1%. (xi) Applying one coat of solar reflective bituminous aluminium paint @ 0.10 Kg/Sqm over APP membrane surface complete.

M&L 10 mm thick cm layer of (1:3) with WPC when the concrete is still green etc complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls etc including raking out joints, hacking for keys, scrubbing down with water complete all as specified including necessary scaffolding and safety arrangement etc complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) not exceeding 1.5 sqm each.incl taking down grill and stacking for issued under Sch of Credit etc complete all as specified and directed.

All as per item No 5.00 above but exc 1.5 Sqm but n.exc 4 Sqm each etc complete all as specified and directed.

Taking down the grill not exceeding 2sqm each.incl taking down grill and refixing the same in the same opening after complete cleaning and when the repair work is complete or as and when directed by the Engr in Charge.

Taking down chowkats or frames, not exc 1.5 sqm each with wooden/ flush/ PVC shutters (Without taking off shutters from the frame) including taking down of hold-fasts by cutting/chasing etc from existing surfaces and also taking down of MS Grills (where exists), refixing the same after proper cleaning and when repairs to plaster etc complete all as specified and directed.

Taking down chowkats or frames, not exc 1.5 sqm but not exc 4.0 sqm each with wooden/ flush/ PVC shutters (Without taking off shutters from the frame) including taking down of hold-fasts by cutting/chasing etc from existing surfaces and also taking down of MS Grills (where exists), refixing the same after proper cleaning and when repairs to plaster etc, complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed.

S&F powder coated standard aluminium section anodised shutters for doors, window / ventilators, partitions, fixed / openable / sliding or in any pattern, cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass, provision of hinges, screws, plugs, handle, lock, roller, Nylon ball bearing etc complete all as specified and directed (Aluminium section shall be of make Jindal/Hindalco/ Indalco) Note:- Weight of Aluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. Cost of other items / accessories required for entire completion of the work shall be deemed to be included in the quoted rate. However glass panes and wire cloth shall be measured and paid separately as supply only under respective items.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supply and fixing in opening as per specification given under SSR Part II 2010 including making good the disturbed surface etc complete all as specified and directed. Make: Rajashree or equivalent.

M&L for factory made solid PVC panel type PVC door shutter 30mm thick consisting of frame madeout of MS tubes for top and bottom rails MS frame shall be covered with moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rails, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent supplying and fixing in the frame at site as per specifications and drawing given under SSR Part II 2004 etc complete all as specified and directed. Make : Rajashree or equivalent.

S&F 2nd class hard wood plain, solid straight chowkats and frame, wrought framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints including good the disturbed surfaces of walls etc complete all as specified and directed.

S&F 2nd class hard wood 35mm thick, plain, framed panelled shutters (any number of panels), with panels of timber flat on both sides (Feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers, fitted to chowkats etc complete all as specified and directed.

S&F 2nd class hardwood 35mm thick glazed and skeleton shutters open and prepared to rceive glass ,gauze etc (with sash bars) edges of plain, chamferred or rounded, fitted with cut and mitred beads for securing gauzes etc, sizes of members of sizes of shutters as specified in SSR part -I sec 8,cluse 8.24(a) etc complete all as specified and directed.

M&L for preparation of new or previously untreated wood based surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer etc complete all as specified and directed.

S&F MS hold fasts and similar small articles etc complete all as specified and directed.

S&F aluminium anodised sliding door bolts with hasp and staple (Bolt type) and fixing clip of lsheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, length of bolt 300mm etc complete all as specified and directed.

S&F stainless steel butt hinges with extruded aluminium alloy with galvanised mile steel hinges pins 100mm size etc complete all as specified and directed.

S&F aluminium anodised barrel tower bolt of extruded section of size 150 mm length. etc complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolts of extruded section and fixed 200 mm etc complete all as specified and directed.

S & F 150 mm long extruded aluminium alloy handles, fabricated type anodised etc complete all as specified and directed.

Supply only 5 mm thick plain sheet glass, ordinary quality, etc complete all as specified and directed.

S&F 5 mm thick plain sheet glass, ordinary quality with and including provision of new rubber gasket after hacking out old broken glass (any size, quality or description) for existing aluminium joinery, etc complete all as specified and directed.

Supply only aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm for new aluminium joinery, complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples etc complete all as specified and directed.

M&L for 12 mm thick polymer modified ready mix cement based plaster on the wall surfaces including finishing surfaces even and smooth, etc complete all as specified and directed. Make: Easy Plast from M/s wall plast or chemplast or readyplast from Ultratech Note: The thickness of plaster specified above is the minimum thickness and the quoted rates shall also be deemed to include for provision of dubbing of the surfaces with ready mix plaster and nothing extra shall be payable on this account.

M&L for rendering 05 mm thick in cement mortar (1:3) to ceiling, finishing the surfaces even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls including necessary scaffolding and applying two coats of acrylic exterior paint over a coat of acrylic primer as approved by GE complete all as per manufactures instructions etc complete all as specified and directed.

M&L for 3 mm thick (minimum) white cement based wall care putty in two coats on new or old surfaces of walls/ceilings etc, finished even and smooth, complete all as specified and directed.

M & L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper with roller over one coat of primer, complete all as specified and directed.

M & L for preparation of new plastered surfaces of ceiling and applying two coats of oil bound distemper with roller over one coat of primer, etc complete all as specified and directed.

M&L for coloured 450x300x6mm thick glazed ceramic tiles on vertical surfaces such as skirting,dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the colour of tiles, over and including 10mm thick cement mortar backing coat in CM 1:4, etc complete all as specified and directed.

M&L for coloured Non-skid ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with nthe colour of tiles, over and including 15mm thick cement mortar screed bed in CM 1:6, etc complete all as specified and directed.

M&L for Non Skid ceramic tiles 7 to 8 mm thick, coloured (squares/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 etc complete all as specified and directed.

M&L for 20 to 25 mm thick machine cut pre-prolished cuddappa stone Slabs (table rubbed and polished) as in cills, jambs, soffits, cooking platform etc, pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of stone slab etc, including moulding/rounding to edges of the slab and also including provision of 15mm thick screed bed in CM 1:4, etc complete all as specified and directed.

S&F in repairs, white, vitreous China, wash down water closet pan (pedestal pattern), Ist quality, inlcuding plastic water closet seat white, closed pattern with flat bottom and cover and Mild Steel CP or aluminised hinging device, complete all as specified and directed. Note: Flushing cistern, flush pipe will be measured and paid for separately.

M&L health faucet of 15 mm dia with 1 m tube hook , Cat No 187 of Prayag or equivalent make as approved by the GE etc complete all as specified and directed.

S & F in repairs flushing cistern, 10 Ltrs. Capacity, PVC valveless, syphonic action type with dual flushing system, low level,white with inlet, ball valve,float and handle including brackets, flush pipe of polyethylene of low or high density or PVC, 32mm dia, etc complete all as specified and directed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and as directed.

S&F two way Bib cock of Pryag make Cat No SQT-512 ANKN or of ESSCO or equivalent of Marko ,Parko as approved by the GE complete all as specified and directed.

S&F in repairs Vitreous China white, 1st quality, wash hand basin, flat back, size 550mm x 400mm including mild steel angle brackets,CP brass fittings, waste, union, 32mm dia PVC waste pipe, cutting for and pinning ends of brackets,etc complete all as specified and directed.

M&L 40 mm dia Low density polyethylene (LDPE) pipes of pressure rating 6kgf/sq. cm etc complete all as specified and directed.

S&F 15mm bore brass CP pillar tap, Make ESSCO Cat No MQT-507 or equivalent of make Parko as approved by the GE, etc complete all as specified and directed.

S&F 15mm bore brass CP Stop Valve, Make ESSCO Cat No MQT-513 A or equivalent of make Parko/ ZOLOTO as approved by the GE, etc complete all as specified and directed.

S&F 15mm bore brass CP Bib Tap, Make ESSCO Cat No MQT-511 or equivalent of make parko as approved by the GE, etc complete all as specified and directed.

S&F in repairs brass chromium plated, shower rose, 125mm size with and including 195mm long 15mm bore brass chromium plated shower arm with bend of 45 degree, complete all as specified and directed.

S&F in repair Grating doom 125 mm dia with waste hole of PTMT (Minimum Weight 25 gram), complete all as specified and directed.

Taking up or down steel water tubing and connections of size 15mm bore, complete all as specified and directed.

Taking up or down steel water tubing and connections of size 20mm bore, complete all as specified and directed.

Taking up or down steel water tubing and connections of size 25mm bore, complete all as specified and directed.

Supply & fixing 15mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors, etc complete all as specified and directed.

Supply & fixing 20mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors etc complete all as specified and directed.

Supply & fixing 15 mm CPVC pipes UV stable,leak proof, tough ,rigid , conforming to IS:15778 of SDR 11 standard., medium grade with and including all fittings and fixed to walls and ceilings or laid in floors, etc complete all as specified and directed.

Supply & fixing 25mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors etc complete all as specified and directed.

S & F of 75 mm bore uPVC (SWR) soil, waste, ventilating rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints, complete fixed to wall with necessary PVC standard stay clamps etc, including taking down existing SWR pipes(including fittings) of any description, etc complete all as specified and directed.

S & F 110 mm bore uPVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints, complete fixed to wall with necessary PVC standard stay clamps etc, including taking down existing SWR pipes(including fittings) of any description, etc complete all as specified and directed.

S&F 75mm bore uPVC (SWR) branch piece single (Single Y), equal or unequal with and including rubber ring joints, etc complete all as specified and directed.

S&F 110mm bore uPVC (SWR) branch piece, single (single Y), equal or unequal with and including rubber ring joints, etc complete all as specified and directed.

S&F 75 mm bore uPVC (SWR) Bends with and including oval access door and also including rubber ring joints, etc complete all as specified and directed.

S&F 110 mm bore uPVC (SWR) Bends with and including oval access door and also including rubber ring joints, etc complete all as specified and directed.

S&F PVC (SWR) floor trap with 75mm dia out let including grating, connecting, jointing to waste pipe with lead joints, also including embedding the same in PCC 1:2:4 type B-1 (using 20mm graded stone aggregates) mixed with water proofing compound in the proportion as recommanded by the manufacturer(s), taking out existing unserviceable traps by hacking out concrete joints and making good of surfaces, etc complete all as specified and directed.

M & L for filling of lean concrete 1:5:10 type E2 (using 40 mm graded stone aggregates ) for filling in sunken portion, as per requirement, etc complete all as specified and directed.

M&L for PCC 1:2:4, type -B-1, using 20mm graded stone aggregated as in sub base of sunkun floor mixed with WPC in the proportion as recommanded by the manufacturer(s), etc complete all as specified and directed. Note : WPC will be measured and paid separately as supply only.

Material and labour for rendering 15 mm thick rendering in CM 1:4 mixed with WPC in the proportion as recommanded by the manufacturer(s), over top of sunken floor, roof surfaces etc, finished even and fair, etc complete all as specified and directed. Note: WPC shall be measured and paid as "supply only" separately.

M&L for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.20 Kg/Sqm including cleaning the surfaces over newly plastered surfaces of sunken portion, etc complete all as specified and directed.

Supply only intergal water proofing compound, etc complete all as specified and directed.

S&F 20 mm dia brass chromium plated tubular towel rail 'D' type 600 mm long between flanges, etc complete all as specified and directed.

Dismantling existing water tanks of capacity exc 250 ltrs and not exc 500 ltrs, etc complete all as specified and directed.

Supplying and fixing rotational moulded polythylene water storage tanks, double layered (ISI marked) of 500 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I, including provision of necessary fittings for connecting the overflow ball brass valves, high pressure, with polythene float and flynut drain out, inlet and outlet pipes, etc complete all as specified and directed..

S&F in repairs gunmetal gate valve, ISI marked with iron wheel head, screwed at both ends for iron pipe or ferrule of 25mm bore and provision of necessary fittings like unions, check nuts, etc complete all as specified and directed.

S&F in repairs 20mm dia Harrison rails, mild steel, chromium plated, curtain rails with and including fixing brackets, stops, rollers etc complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortor of any dia, etc complete all as specified and directed.

M&L for Salt Glazed, Stoneware, Drain pipes of 150mm bore, grade 'A', laid in trenches and jointed, etc complete all as specified and directed. Note: Excavation & earth work and PCC for bedding & haunching shall be measured and paid for separately.

M&L for 100mm thick concrete bed in cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) for 150mm bore pipes including packing under and haunching against the sides of pipes after they are laid and tested etc complete all as specified and directed.

Excavation in trenches not exc 1.5m wide and not exc 1.5m in depth for pipes, foundation etc and 10 Sqm on plan and not exc1.5 metre in depth for pits, independent holes etc, including getting out in any type of soil, etc complete all as specified and directed.

Returning, filling in with approved earth including spreading, levelling, watering, well ramming in layers n exc 25 cm thick, etc complete all as specified and directed.

Removing excavated material/soil to a distance not exceeting 50 metre and depositing where directed at a level not exc 1.5 metre above the starting point, etc complete all as specified and directed.

Chipping, removing carefully loose/damaged concrete including plastering (total thickness upto 40mm ) from surfaces of RCC members, in any location by low impact Hammer/Breakar without damaging the structure & cleaning the surfaces with wire brush etc and disposal of debris out side MD land etc complete all as specified and directed. Note : Hard concrete shall not be removed by force

M&L for cleaning existing reinforcement with wire/ rotary wire brush to a shining bright finish, making the surfaces free from loose material, dirt etc complete and applying two coats of alkaline rust converting primer conforming to ASTM-B-117 of make. "Feovert" of "Krishna Conchem" OR "Roff Rust Cleaner' of 'Pidilite' OR 'Shali Rustoff' of 'STP Ltd', on rebars with time interval of 1 hour between the coats, etc complete all as specified and directed. Note :- Mode of measurement: superficial area of concrete will be measured.

M&L for Anticorrosive Treatment to Reinforcement using Corroseal - ZR of M/s Krishna Conchem or Epoxy Zinc Primer of M/s. Dr. Fixit by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces etc complete all as specified and directed. Note : Mode of measurement: superficial area of concrete will be measured.

M&L for providing additional mild steel TMT bars in various structural RCC members like column, beams and Slab etc. including cutting, bending, fixing the bars, tying with and including binding wire etc complete all as specified and directed.

M&L for shear connectors of 8mm dia TMT bars including anchoring of the reinforcement bars in existing RCC member by providing holes of minimum 10d depth and grouting in position with locfix (fosroc), including drilling of holes, cleaning and other relevant works, etc complete all as specified and directed.

M&L for Epoxy bond coat of Make Fosroc (NITOBOND-EP) OR EPOXY BONDING AGENT of Dr. Fixit OR equivalent of M/s. Krishna Conchem as approved by GE over exposed concrete surfaces prior to application of any type of mortar to ensure bond between old concrete & new concrete / mortar by brush application, etc complete all as specified and directed.

M&L for casting & repairing of excessively damaged distressedRCC members with prebatched, prepacked, single component ready to use microconcrete from M/s. Krishna Conchem Molith MC) or equivalent of Dr. Fixit as approved by GE at any level and at any lead or lift as directed including scaffolding , also including mixing , laying, levelling, finishing, curing etc as per manufacturer's specifications etc complete all as specified and directed. Note : Reinforcement & formwork shall be only shall be measured and paid separately.

M&L for building up the profile of structural members using polymer modified mortar from M/s. Krishna Conchem (Molith PMM) OR Polymer mortar HB of Dr Fixit, while the bonding agent is still tacking upto 20mm thickness, including levelling, profiling, formworking ,scaffolding etc complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for and removing the retreived debris out side MD land, etc complete all as specified and directed.

M&L Hardcore of gauge not exc. 63mm, deposited, spread and levelling in layers not exc. 15 cm thick, watered and rammed to true surface with broken stone or boulder etc complete all as specified and directed.

M/L75 mm thick Cement Concrete in sub base of floors type D-2, PCC 1:4:8 ( 40mmgraded aggregate ) etc complete all as specified and directed.

M&L for coloured Parking tiles, heavy duty of size 300x300x10 mm thick, set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match the colour of the tiles, over and including 15mm thick cement mortar screed bed in CM 1:6, etc complete all as specified and directed. Make : JOHNSAN /SOMANI/ORIENT BELL/KAJARIA.

Taking down copper/ aluminum point wiring (Light/Fan/Socket or power) complete including fixtures and fittings such as switches, ceiling roses, pendants, regulators, socket, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces to walls floors etc complete all as specified and directed.

Taking down of Old MCB DB of any size with its components etc complete all as specified and directed.

Taking down submain wiring any size etc complete all as specified and directed.

M & L for point wiring with PVC insulated unsheathed 1100 Volts grade single core multistranded copper conductor cable 1.5 Sqmm drawn in and including PVC casing-caping and accessories, fixed on wall / ceiling etc with neccessary fixing accessories and earth continuity conductor cable of 1.5 Sqmm size connected to common earth and earth dolly including 2 mm thick pressed steel terminal boxes concealed in wall covered with laminated sheet top cover 3 mm thick for mounting switches / sockets / fan regulators fixed with Cadmium plated machine screws all as specified for the following: (a) One light / fan / bell point controlled by one switch.

All as per above item No 96.00 above but one 5A 2pin/3pin socket out let multipurpose on the same board with other switches etc complete all as specified and directed.

All as per above item No 96.00 above but one 5A 2pin/3pin switch socket out let multipurpose on independent board etc complete all as specified and directed.

All as per above item No 96.00 above but wiring complete with 2.5 Sqmm for 3 pin 15A socket multipurpose on independent board etc complete all as specified and directed.

Supply & Fix switch piano single pole flush type 5A, 240 V one way etc complete all as specified and directed.

Supply & Fix Bell push flush type 5 amp, 230 Volts etc complete all as specified and directed.

Supply & Fix switch socket combination 2 in 1, 5 Amps multipurpose flush type etc complete all as specified and directed.

Supply & Fix switch socket combination 2 in 1, 3 pin, 5 and 15 Amps flush type universal etc complete all as specified and directed.

Supply & Fix Ceiling rose surface bakelite three terminal, 240 V, polycarbonate body etc complete all as specified and directed.

Supply & Fix electronic regulator Step type 2 module type 240V suitable for ceiling fan etc complete all as specified and directed.

Supply and fix bell ding dong AC 230 V single pole etc complete all as specified and directed.

S&F Retro LED tube rod 20 Watts, 230 volts, with high efficency PMMA diffuser etc complete all as specified and directed. The tube rod shall confirm to Cat No SZFRTMX020 of Shakti or Equivalent from Crompton / Philips / Bajaj

S&F decorative box type fitting prewired for Retro LED light fitting 20 Watts, 230 volts, including 2 Nos PVC Square blocks , scews , 3 core 1.5 Sqmm cable for connection between ceiling rose & fitting complete all as specified and directed. The fitting shall confirm to Cat No SZRFMX1-20 of Shakti or equivalent from Crompton/Philips/Bajaj

S&F Retro LED tube rod 10 Watts, 230 volts, with high efficency PMMA diffuser, the rod shall etc complete all as specified and directed. The tube rod shall confirm to Cat No SZFRTMX010 of Shakti or Equivalent from Crompton/Philips/Bajaj

S&F decorative box type fitting prewired for Retro LED light fitting 10 Watts, 230 volts, including mounting blocks fitting fixing check nuts ,3 core 1.5 Sqmm cable for connection between ceiling rose & fitting etc complete all as specified and directed. The fitting shall confirm to Cat No SZRFMX1-18 of Shakti or equivalent from Crompton/Philips/Bajaj

M & L for Painting of ceiling fans/exhaust fans with louvers complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust and Hanging only ceiling fan taken and connecting up including provision of cable from ceiling rose or connector to fan etc complete all as specified and directed.

Supply & Fix MCB DB Double Door SPN 8 way 240 volts, including cutting chasis in wall, concealing the DB in wall, making good the distrubed surfaces and making connections etc complete all as specified and directed.

Supply & Fix MCB DB Double Door TPN 6 way 415 volts, including cutting chasis in wall, concealing the DB in wall, making good the distrubed surfaces and making connections etc complete all as specified and directed.

M&L for MCB SP, 240 volt, 6 to 32 Amps, 10 KA etc complete all as specified and directed.

M&L for MCB SPN, 240 volt, 32 Amps, 10 KA etc complete all as specified and directed.

Supply and fixing 415V 10KA 'B' curve miniature circuit breaker (MCB) of 32A TPN and current carrying capacity in the DB complete with connection testing and commissioning etc complete all as specified and directed.

Supply and fixing 415V 10KA 'B' curve miniature circuit breaker (MCB) of 63A FP and current carrying capacity in the DB complete with connection testing and commissioning etc complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded Copper conductor of size 6.0 sqmm 2 core etc complete all as specified and directed.

Supply and fixing LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.complete including taking down of old fitting etc complete all as specified and directed. The fitting shall confirm to Cat No - SZPSLPM060 of Shakti or Equivalent to Crompton/Philips/Bajaj

S& F in replacement of GI steel tubing medium grade 40mm dia and length up to 1.5 meter bent to shape of offset angle upto 45degree for fixing of security /street light fittings including MS clamps made of 32mm x5mm flat iron, nuts, bolts, etc and taking down of old bracket etc complete all as specified and directed.

Taking out old unserviceable underground cable XLPE insulated, PVC sheathed armoured heavy duty aluminum conductor LT 1100 Volts grade of size 3.5 Core 25 Sqmm, etc complete all as specified and directed. Note - Excavation and earth work will be mesured and paid seprately.

Supply and laying un-reinforced precast concrete cable cover class LV, type-I, flat size 250mm x 150mm x 40mm laid in trenches etc complete all as specified and directed.

Taking out un-reinforced precast concrete cable cover and laying old class LV, type-I, flat size 250mm x 150mm x 40mm laid in trenches etc complete all as specified and directed.

M & L for sand cushioning by spreading in trenches fine dry river sand by gently by punning down manually as in cable protection etc complete all as specified and directed.

Supply and Laying or fixing or passing through pipe, XLPE insulated, ISI marked armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 25 Sqmm 3.5 core in trenches, along the wall including necessary connection and providing cable lugs as required etc complete all as specified and directed.

M&L for cutting existing road/hard standing not exc 45x45 cm in wide & depth getting out excavated material for laying GI tube ;returning filling & well rammaing watering finish suraface 10 cm from top using PCC 1:3:6; including removal of surplase soil etc complete all as specified and directed.

S&F of HDPE pipe 100 mm dia, PN-10 for laying in ground, raod crossing etc for cable protection including necessary fittings, clamps for supports, etc complete all as specified and directed.

M&L for earthing using GI earthing strip 32 x 6mm complete with galvanised steel earth plate electode 600mmx600mmx6mm thick buried directly in ground, earth pit not less than 2.25 meters deep below ground level connection to and including GI strip of size 32x6mm to the extend 7.5 mtr as earth lead by means of GI bolts, Nuts etc. with provision of charcoal and salt all as per electrical plate No 3 of SSR Part I including water arrangement with GI Pipe 20 MM dia (medium Grade), earth lead protection pipe 50mm madium grade with bends, elbow etc. from earth plate to test point, excavation and earth work returning, filling, ramming and removing of soil to distance not exc 50mtr, make good to match with existing surface making PCC pit (Earth chamber) having internal size 30cm x 30cm x 30cm and outer size 60cm x 60cm x 60cm with RCC reinforced cover 50mm thick with one lifting handle made of 8mm dia MS bar funnel wie mesh and testing on completion including making test point on wall as per SSR specification all as specified etc complete all as specified and directed. Note : A sum of Rs 18,573.00 towards sch of credit shall be deducted to arrive the contract sum.

M/s Hari Om Construction

Atharva Enterprises