ADDITION ALTERATION TO SINGLE OFFICERS ACCN BLDG NO T-67, T-68 ALONGWITH SPL REPAIR TO BLDG NO T-18, T-21,T-67B OTM ACCN AND BLDG NO P-1, SINGLE OFFRS ACCN, IN THE AOR OF AGE BR-II UNDER GE 969 EWS

Amount

Demolition of cement concrete in ground floor and paving n.exc 15cm thickness (below & above GL) unreinforced complete all as specified and directed.

M&L 75mm thick PCC 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection and similar works including finishing the surface of concrete topping even & fair, without using extra cement complete all as specified.

M&L for 75 mm thick PCC 1:4:8 type C-2 (using 40 mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for 75 mm thick PCC 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in sub base of flooring to receive tile complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L non skid ceramic coloured tiles (joint free tile) area of each tile (square/rectangle) exc 0.06 Sqm but not exceeding 0.11 Sqm tile thickness 7 to 8 mm, in floors etc set and joined in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer 15mm thick with CM 1:6 for laying floor finishes complete all as specified and directed.

M&L non skid ceramic coloured tiles (joint free tile) area of each tile (square/rectangle) exc 0.11 sqm but not exceeding 0.18 sqm tile thickness 7 to 8 mm, in floors etc set and joined in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

S&F glazed coloured ceramic tiles 350x350mm/450x350mm and 8mm thick, in dado / skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for vitrified ceramic tiles 10 mm thick light shade (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Taking down chowkhats with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n.exc 4 Sqm each and offered as credit complete all as specified and directed.

-Ditto- all as per item No 11 here in before but n exc 1.5 Sqm each complete all as specified and directed.

Taking down shutters of any description area exc 1.00 Sqm and n exc 2 Sqm each complete all as specified and directed.

-Ditto- all as per item No 13 here in before but n exc 1.00 Sqm each complete all as specified and directed.

Taking down shutters of any description area exc 2 Sqm each and refixing in same opening after necessary repairs/re-size complete all as specified and directed.

Taking down shutters of any description area exc 1.00 Sqm but n.exc 2 Sqm and refixing in same opening after necessary repairs/re-size complete all as specified and directed.

Forming jambs, etc. to openings (to foregoing item), including cutting, toothing, and properly bonding into old work, also facing, jointing and pointing to match existing work, with CM 1:4 complete all as specified.

S&F powder coated anodised aluminium frame for sliding windows, ventilators and with one or more rebates including jointing cleat and handles and other necessary fittings for fixing etc complete all as specified and directed.

S&F powder coated anodized aluminium window and ventilators shutters, without sash bar, aluminium section weighting 0.55kg / m including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, locking arrangement, handles etc complete all as specified and directed.

S&F second class hard wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F second class soft wood (kail) plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints and treating back of chowkhats etc with tar of coat black paint complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with wooden beading or with nuts and bolts to existing steel windows/wooden windows complete all as specified and directed.

S&F 2nd class soft wood (kail) 35 mm thick plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkhats complete all as specified and directed.

M&L prelaminated particle board interior grade, 18/19 mm thick with both faces white base, fixed with screws to timber frame work as in shelves/ cupboard shutters and partitions add fixed and repairs complete all as specified and directed.

M&L extra 6mm thick external teak wood lipping to block board or veneered particle board of 18/19 mm thickness of board complete all as specified and directed.

S&F 100mm long hasp & staple, safety type, brass hinges pin including bolt to hinges plate & fixed with screw complete all as specified and directed.

S&F continuous (piano) hinges,40mm wide mild steel, bright finish or electro galvanised complete all as specified and directed.

S&F 150mm extruded brass handles, fabricated type polished complete all as specified and directed.

S&F butt hinges,100mm medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F brass, sliding door bolt 250mm long with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete, all as specified.

S&F floor door stopper 140 mm long of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and directed.

Hacking out old broken glass any thickness, size, quality, from wooden frame/steel frames fixed with putty or with wooden beads complete all as specified and directed.

S&F sheet glass 4 mm thick ordinary quality one way glazing with rubber gasket in square not exc 0.5 sqm each pane complete all as specified and directed.

S&F sheet glass 5 mm thick ordinary quality one way glazing with rubber gasket in square not exc 0.5 sqm each pane complete all as specified and directed.

S&F in repair 12mm thick plain toughened glass in glass cubical partition with SS fixtures etc complete all as specified and directed.

Dismantling PVC water tanks, 1000 liters capacity & removing from site complete all as specified and directed.

S&F FRP rotex PUF insulation tank 1000 ltr capacity consists of outer layer of tank white in colour made up of virgin FRP, inner layer of tank white in colour made up of virgin LLDP/HDPE, in middle of both the layers polyurethane fome (PUF) of 50 mm thick, including inlet along with float valve, outlet, overflow provision and tank lid with a suitable locking system complete all as specified and directed.

Taking down GI water tubing and connections and removing from site for 20mm bore complete all as specified and directed.

S&F tubing, medium grade, galvanised, 20 mm bore with all fittings, fixed to walls and ceilings or laid in floors complete all as specified and directed.

M&L for lagging on 15 mm internal dia pipe all round with 50 mm thick bonded mineral wool pre-formed 'SNAP ON' pipe section of density of 144 Kg/Sqcm confirm to IS 9842 including providing with chicken mesh wire netting 25 gauge 20 mm mesh and 0.01 mm aluminium foil etc complete all as specified and directed.

M&L for lagging on 20 mm internal dia pipe all around with 50 mm thick bonded mineral wool pre-formed 'SNAP ON' pipe section of density of 144 Kg/Sqcm confirm to IS 9842 including providing with chicken mesh wire netting 25 gauge 20 mm mesh and 0.01 mm aluminium foil etc complete all as specified and directed.

M&L for lagging on 20mm internal dia pipe anti-freezing wire unlike the normal wires, a heating element, fire proof quality works on electricity only, subjected to a temperature of 80°c for both GI and PVC pipes, underground or upper ground post wiring the pipes, insulating layer of waterproof tapping (pipes, wires and insulating layer) against any exposure, works on a low electric voltage with an auto cut sensor to prevent over-heating (1.5 square mm wire with MCB ) etc complete all as specified and directed.

M&L for lagging on 15mm internal dia pipe anti-freezing wire unlike the normal wires, a heating element, fire proof quality works on electricity only, subjected to a temperature of 80°c for both G.I and PVC pipes, underground or upper ground post wiring the pipes, insulating layer of waterproof tapping (pipes, wires and insulating layer) against any exposure, works on a low electric voltage with an auto cut sensor to prevent over-heating (1.5 square mm wire with MCB) etc complete all as specified and directed.

S&F only water meter, metal stop cock gunmetal gate valve, brass ball valve, gunmetal non-returning valve in PP-R pipe line (cost of male sockets included) complete all as specified and directed.

S&F PP-R gate valves (brass insert) as per requirement of the site complete all as specified and directed.

S&F PP-R ball valves (brass insert) as per requirement of the site complete all as specified and directed.

S&F 20mm outer dia of 3 layer PPR polypropylene random copolymer concealed pipes SDR 7.4 (PN-16) unstalised and antimicrobial fusion welded having thermal stability for hot or cold water supply including all PPR pain & brass threaded polypropylene random fittings fixed to wall, ceiling or in floors complete all as specified and directed.

M&L preparation of new or previously untreated wooden surfaces of any description, not otherwise described, over 10cm width or girth applying two coats synthetic enamel paint over one coat of pink primer complete all as specified.

M&L preparation of old or painted wooden surfaces of any description, not otherwise described, over 10cm width or girth applying one coat synthetic enamel paint over one coat of pink primer complete all as specified.

S&F in repairs vitreous counter top wash basin, white, flat back, size 550x400mm including 32mm waste fittings, brass, chromium plated for glazed ware basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

M&F for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

S&F vitreous china wash down water closet (Single unit) including flushing cistern white/coloured match to the tiles fixed to floor complete all as specified and directed.

S&F PVC connections 15 mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F PVC connections 15 mm size with PTMT nuts of length 600mm fixed to GI tubing complete all as specified and directed.

S&F in repairs 15mm fancy type chromium plated angle cock with flange, screwed down, high pressure, with crutch handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs 15 mm bore bib cock long body with flange, fancy type chromium plated, screwed down, screwed for iron pipe, or for brass ferrule and fixed complete all as specified and directed.

S&F in repairs tall basin mixer pillar tap type fancy type chromium plated, screwed down, high pressure, with or without lettered ‘HOT’ or ‘COLD’ with long screwed shanks and fly nuts, screwed for 15 mm bore complete all as specified and directed.

S&F in repairs CP wall mixer with for mixing hot & cold water screwed down for iron pipe & fixed with provn for connection to over head shower with bend pipe complete all as specified and directed.

M&L in repair brass chromium plated wall mixer with hand shower @ 100mm round shape complete all as specified and directed. Make:- Jaquar/Cera/Hindware

S&F in repair health faucet mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F toilet paper holder premium quality, stainless steel or brass chromium plated complete all as specified and directed.

S&F corner glass shelves (with brackets) for bathroom, complete all as specified and directed.

S&F towel rail 600mm long of SS fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as specified and directed.

S&F in repairs sinks with drainage board made of stainless steel 0.8mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F in repairs PVC gully trap with cover of size 125mm including PCC bed complete all as specified and directed.

S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement etc complete all as specified and directed.

S&F PVC (SWR) pipes single socketed 75mm bore, in any length with rubber ring joints laid in trenches or floors complete all as specified and directed.

S&F PVC (SWR) bends 75mm bore complete all as specified and directed.

S&F PVC (SWR) pipes single socketed 110mm bore, in any length with rubber ring joints laid in trenches or floors complete all as specified and directed.

S&F PVC (SWR) bends 110mm bore complete all as specified and directed.

S&F 110mm PVC (SWR) junction single (single T) equal or unequal complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based profile steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPA as in roof covering/cladding to wall, fixed with self tapping screw including dismantling complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

M&L for 6 mm thick plywood, grade BWR type BB, fixed with nails to timber frame work on wall etc complete all as specified and directed.

M&L for second class softwood (kail) 12 mm thick planed on both side and edges tongued and grooved or rebated and joints are chamfered one side and the boarding is matched, fixed with nails in walls including preparing the surface and applying french polish over a coat of wood filler in new work with two or more coats complete all as specified and directed.

M&L for 12 mm thick plywood, grade BWR type BB, fixed with nails to timber frame work in ceiling etc complete all as specified and directed.

S&F decorative wooden tiles of size 300x300 and 10mm thick of second class softwood, with fixing on ceiling of nails and glue/ fevicole over a 12 mm Plywood, design and shade as approved complete all as specified and directed.

M&L for french polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with one or more coats complete all as specified and directed.

S&F 2nd class softwood (kail) lean sawn with butt joints eaves boards 20 mm thick complete all as specified and directed.

M&L weather boarding, clean sawn, plain,20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps and fixed complete all as specified and directed.

S&F 25 mm thick 2nd class soft wood (kail) planed one side & edges tongued and grooved or rebated, with nails in flooring and skirting complete all as specified and directed.

M&L for complete removal of existing treatment on old wall surfaces & finishing walls with acrylic smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 Sqm) new surfaces or old decorated surfaces complete all as specified and directed.

S&F 4 mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces; fixed with nails to timber frame work on ceiling complete all as specified and directed.

S&F 4 mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces; fixed with nails to timber frame work on wall complete all as specified and directed.

M&L for 5 mm thick plain colour PVC sheet in strips & channel feathered at the edges for fixing on solid PVC wall lining, insulated PVC wall lining, and solid PVC portions & ceiling etc inclusive of solvent cement & fixing at site complete all as specified and directed.

Preparation of new steel and iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

M&L painting old steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint including preparation of surfaces complete all as specified and directed.

Dismantling timber scantling 40 sq cm and over in section in any position as in unframed work, complete all as specified and directed.

-Ditto- all as per ser item No 91 but in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section, in any position complete all as specified and directed.

Dismantling timber scantling under 40 sq cm in section in any position as in unframed/framed work, complete all as specified and directed.

M&L 2nd class soft wood (Kail) as in scantling, clean swan timber fixed, complete all as specified and directed.

M&L 2nd class soft wood (kail) plain fillets exc 13 Sq.cm , n exc 25 Sq.cm rectangular in section, clean sawn screwed with nails or brads complete all as specified and directed.

M&L 2nd class soft wood (kail) plain fillets exc 3 Sq.cm but n.exc 6 Sq cm , rectangular in section, clean sawn screwed with nails or brads complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

M&L brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and directed.

M&L for rendering plaster 10 mm thick on fair faces of brick work or concrete surface in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and directed.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:4 complete all as specified and directed.

-Ditto- all as per item ser No 100 but except stone complete all as specified and directed.

Taking down cement or cement lime plaster, on brick or stone walls,/ceiling etc. including raking out joints, hacking for key, scrubbing down with water, etc. any description complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement mixing with integral water proofing compound complete all as specified and directed. Note : WPC shall be measured and paid separately.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement with water proofing compound complete all as specified and directed. Note : WPC shall be measured and paid separately.

M&L rendering 10mm thick on fair faces of brick work or concrete surfaces on wall in CM 1:4 finished even and smooth without using extra cement mixed with water proofing compound complete all as specified and directed. Note : WPC shall be measured and paid separately.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls, applying two coats of distemper oil emulation, white tinted complete, all as specified.

M&L for preparing newly plastered surfaces of walls, applying two coats of cement base paint complete, all as specified.

S&F framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, for Fe 410 -W (Gde- E- 250) quality- A complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed.

M&L plain cement concrete 1:2:4 type D-2 (40mm graded stone aggregate) in foundation, filling and mass concrete complete all as specified and directed.

M&L cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring etc. and making good, cutting not exc 10cm girth complete all as specified.

M&L new steel or iron surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide/zinc chromate primer including preparation of surfaces complete all as specified and directed.

M&F for granite (of any type) 18- 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

Rounding to edges of granite/stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for pre- cast reinforced cement concrete M-15 (1:2:4 nominal mix ) type B-1, (using 20mm grade stone aggregate) set in cement mortar 1:4 as in manhole cover complete all as specified and directed.

S&F MS TMT bars 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L complete removal of existing treatment on external wall surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots and surfaces and applying two coats of exterior emulsion weather proof paint over one coat of external wall primer complete all as specified and directed.

M &L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed.

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in any type of hard/dense soil complete all as specified and directed.

Removing of excavated soil not exceeding 50m and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

M&L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75mm thick cement concrete type C-2, 1:3:6 (using 40mm graded stone aggregate) as in sub base of floors, finished even and fair over well/rammed/ compacted earth complete all as specified and directed.

M&L stone sett flooring with stone setts of size 200 to 250mm long, 150 to 200mm wide and 150mm deep and sides dressed; bedded in cement mortar 1:3, joints 20mm thick grouted in cement mortar 1:2 with an admixture of metallic floor hardener 5% by weight of cement and struck flush complete all as specified and directed.

M&L cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L brick work with sub class B bricks straight or curved on plan exc 6m mean radius in CM 1:6 complete, all as specified.

M&L for preparation of old plastered or unplastered surface of wall and applying two coat of white wash complete all as specified.

M&L for preparation of newly plastered surfaces and applying two coats of oil bound distemper, over a coat of primer including chalk whitening on new plastered surfaces of walls complete, all as specified and directed.

S&F factory made PVC solid door/window/ventilator frame of size 50mmx47mm made out of 5mm prelam sheet in stead of plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with M S square tube complete frame fixed with screws/nails /bolts to walls complete all as specified.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F100mm aluminium anodised, barrel tower bolts of extruded section and fixed, all as specified.

S&F aluminium anodised handle 100mm cast type complete, all as specified.

S&F framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165, all as specified.

Taking up or down GI tubing 15mm bore with all connection complete, all as specified.

S&F 15mm bore GI tubing medium grade galvanized with all fittings and fixed complete to walls and ceiling or laid in floor, all as specified and directed.

M&L for glazed ceramic tiles in vertical surface 600x300 and 10 mm thick colour and design (as approved) in vertical surface and jointed in neat cement slurry and pointed in whiter or colour cement to match the colour of tiles over and including 15 mm thick cement plaster using CM 1:4 complete all as specified and directed.

S&F in repairs vitreous china squatting pan ‘Orissa’ pattern, size 580 x 440 mm white, integral foot rests including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor, all as specified and directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern) white or coloured excluding flushing cistern and flush pipe and seat cover including provision of concrete/ white cementing and P or S trap complete all as specified and directed.

S&F in repairs CP health faucet (ABS) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 mtr long flexible tube and ABS wall hook incl making connection and fixed in position completed in all respect complete all as specified and directed.

S&F in repairs 10 liters capacity PVC low level flushing cistern complete with ISI marked body and ISI marked syphon complete, all as specified.

M&L complete removal of existing treatment on surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot , moulds moss and efflorescent salts , trading oil and greasy spots and applying two coats of oil bound distemper, over a coat of primer including chalk whitening on plastered surfaces of walls preparatory to distempering complete all as specified and directed.

S&F in repairs 15mm fancy type chromium plated angle cock with flange, screwed down, high pressure, with crutch handle, screwed both ends for iron pipe or for unions and fixed, all as specified.

S&F 500 litres capacity rotational moulded, triple layer polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roofs etc, including tank nipples, fittings, including dismantling of existing water tank any type, disposal of rubbish, complete all as specified.

S&F PVC (SWR) vent cowl 110 mm bore fixed complete all as specified

S&F CP bib tap 15 mm bore with crutch or butterfly handle screwed down for iron pipe or for brass ferrule fixed in repair complete, all as specified.

S&F in repairs vitreous china urinal, half stall type, white including flushing cistern, flush pipe and waste pipe complete all as specified and directed.

M&L GI tubing, medium grade ISI marked complete with all necessary fittings of 20mm bore in trenches, all as specified.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in deep in hard/dense soil/road for getting out old GI tubing from the trenches etc. complete, all as specified and directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in hard/dense soil all as specified.

M&L for 12 mm thick plywood, grade BWR type BB, fixed with screws to timber frame work in ceiling etc complete all as specified and directed.

S&F aluminium anodised, barrel tower bolts 150 mm of extruded section and fixed complete all as specified.

S&F aluminium alloy, anodised, sliding door bolt 250 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified.

S&F aluminium handles 150 mm, cast type, anodised complete all as specified.

M&L for preparation of new or previously untreated wooden surfaces of any description, not otherwise described, over 10cm width or girth applying two coats of synthetic enamel paint over and including a coat of pink primer complete all as specified and directed.

Supply only integral water proofing compound, all as specified.

M&L for preparation of newly plastered or unplastered surface of wall and applying two coats of cement base paint over a coat of primer complete all as specified.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

M&L for wooden flooring boarding, clean sawn, plain, 30mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps planed one side, with butt joints and fixed with nails supplied and fixed complete all as specified and directed.

S&F 0.63mm thick, galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 as specified including dismantling of existing sheet complete all as specified and directed.

S&F 0.63mm thick, plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 including dismantling of existing sheet complete all as specified and directed.

S&F 0.63mm thick, galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 but except sheet as specified including dismantling of existing sheet complete all as specified and directed.

S&F vitreous china wash down water closet (Single unit) including flushing cistern white/coloured match to the tiles fixed to floor all as specified and directed.

S&F in repair stop/angle valves 15 mm, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle fancy type chromium plated, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair toilet paper holder with flat recessed premium quality, stainless steel complete all as specified and directed.

S&F in repair vitreous china wash basin, white flat back size 550x400 mm plug, porcelain stopper and including brackets with waste fittings, brass, chromium plated for glazed ware basin etc with long screwed shanks and fly-nuts, flange end bedded in read lead cement and other end fixed and connection pipe etc including pedestal complete all as specified

S&F in repairs pillar taps, 15 mm dia cast copper alloy fancy type with capstan heads, chromium plated. screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts screwed for iron pipe. Complete all as specified

S&F in repairs brass chromium plated tubular towel rail, 20mm dia, 'D' type, 60cm long between flanges complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light. fan, socket or power) complete, including fittings such as switches, ceiling roses, pendants, regulators, sockets etc, removing materials to store for keeping in safe custody for reuse at site and making good disturbed surfaces of walls, floors etc. to match with existing surfaces all as specified.

M&L point wiring complete with FRLS 1100 Volts grade, 1.5 Sqmm PVC insulated and unsheathed copper conductor single core cable drawn through and including 25mm medium grade ISI marked conduit concealed in wall/ceiling all accessories such as bends, elbow , reducers, junction boxes/MS boxes duly painted/ PVC box factory made rectangular in shape as required with top cover 3 mm thick plastic laminated sheets of required size, fixed with screws, for housing switches, sockets, regulators etc, including 1.5 sqmm PVC insulated and unsheathed copper conductor cable as earth continuity wire connected to common earth dolly for one light/ceiling fan/exhaust fan point all as specified and directed for the following:- Note:- Contractor must do internal wiring with chisel cutting in wall/ceiling and fixed conduit and repair surface with plaster 15mm in wall/ceiling and make surface good as it is.

Ditto- all as per Item ser No 174 but for one switch socket combination 5 Amps on independent board.

-Ditto- all as per item ser No 174 but for one switch socket outlet 5 Amps on same board with other switches.

-Ditto- all as per item ser No 174 but 2.5 Sqmm PVC insulated and unsheathed copper conductor single core cable drawn through and including 20 mm medium grade ISI marked conduit concealed in wall/ceiling all accessories such as bends, elbow, reducers , junction boxes /MS boxes duly painted /PVC box factory made rectangular in shape as required with top cover 3 mm thick plastic laminated sheets of required size, fixed with screws, for housing switches, sockets, regulators etc, including 2.5 sqmm PVC insulated and unsheathed copper conductor cable as earth continuity wire connected to common earth dolly all as specified and as directed. Note: Contractor must do internal wiring with chisel cutting in wall/ceiling and fixed conduit and repair surface with plaster 15MM in wall/ceiling to making good to disturbed surfaces to match with existing surfaces.

M&L point wiring complete with FRLS 1100 Volts grade, 4 Sqmm PVC insulated and unsheathed copper conductor single core cable drawn through and including 25mm medium grade ISI marked conduit concealed in wall/ceiling all accessories such as bends, elbow , reducers, junction boxes/MS boxes duly painted/ PVC box factory made rectangular in shape as required with top cover 3 mm thick plastic laminated sheets of required size, fixed with screws, for housing switches, sockets, regulators etc, including 4 sqmm PVC insulated and unsheathed copper conductor cable as earth continuity wire connected to common earth dolly all as specified and directed. Note:- Contractor must do internal wiring with chisel cutting in wall/ceiling and fixed conduit and repair surface with plaster 15mm in wall/ceiling to making good to disturbed surfaces to match with existing surfaces.

M&L for making single phasing point wiring system used as copper conductor wire for phase and neutral wiring system the wire made out of PVC insulated FRLS of 1100 Volts grade with having multistranded copper conductor wire of size 1.5 Sq.mm (Nominal area) ISI marked drawn through wiring system surface on wall with the help of heavy duty ISI mark PVC casing capping strip in any length wiring system and along with its all connected fittings accessories including providing of wooden board with bakelite sheet for housing / mounting of switches sockets, regulators etc and including using /drawing of one run of single wire 1.5 sqmm PVC insulated FRLS wire 1100 Volts grade ISI marked with multistranded copper conductor wire used as a continuous earth wire for point wiring complete system and including making the good to all disturbed surfaces of wall/ceiling to match with existing surfaces for one light point / fan point controlled by one switch of one way point wiring system complete, all as specified & directed by EIC

-Ditto- all as per item No 179 but one 3 pin 5 Amp switch socket outlet on independent board, all as specified.

-Ditto- all as per item No 179 but one 3 pin 5 Amp switch socket outlet on same board with accessories, all as specified.

-Ditto- all as per item No 179 but 2.5 Sqmm size multi stranded FRLS copper conductor cable including clamps, screws gutter/plug etc PVC unsheathed cable into and including wooden board with bakelite sheet and PVC insulated FRLS cable of size 2.5 Sqmm as earth continuity conductor for 15 amps switch socket outlet on independent board, all as specified.

S&F switch piano type 5 Amps single pole one way complete, all as specified.

S&F switch socket combination box type multipurpose 2/3 pin suitable for 5 Amps plug top controlled by one switch complete, all as specified

S&F switch socket outlet two in 1, 3 pin, 5 Amps, 230 Volts complete all as specified.

S&F switch socket combination multipurpose 5 pin/15 Amps box type complete all as specified.

S&F switch piano flush type outlet 6 Amps, 240 Volts, complete all as specified and directed.

S&F flush type socket outlet 6 Amps, 240 Volts complete, all as specified and directed.

S&F in repair ceiling rose surface bakelite surface 65x50mm 3 terminals fixed on wall/ceiling and including PVC block complete, all as specified and directed.

S&F ceiling rose 3 terminal / PVC/polycarbonate, isolated body all as specified and directed

S&F Lamp Holder, PVC/ Polycarbonate type with back plate suitable for batten fitting complete all as specified and as directed

S&F in repair supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified.

S&F in repair modular switch single pole one way 6 Amps 1 module 240 V, complete all as specified and directed.

S&F in repair modular socket, 6A 2/3 pin combined 2 module 240 V, complete all as specified and directed.

S&F in repair modular switch socket combination 16A, 6 pin, 3 module 240 V, complete all as specified and as directed.

S&F in repair modular white cover plate with frame, 8 module, all as specified.

S&F in repair lamp holder, insulated body, threaded dome pattern, suitable for bracket fittings, complete all as specified.

S&F in repair 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 Amps to 32 Amps, in the MCB DB complete with connection testing and commissioning, all as specified.

S&F in repair 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 32 Amps, in the MCB DB complete with connection testing and commissioning, all as specified.

S&F in repair 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 63 Amp, SPN in the MCB DB complete with connection testing and commissioning, all as specified.

S&F in repair MCB DB 12 way sheet metal enclosure SPN 240 Volts, 50Hz with IP-42 protection, single door with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting complete all as specified.

S&F sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 Volts double door with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonry etc and making good of disturbed surface complete all as specified and directed.

S&F in repairs MCB DB 8 way sheet metal enclosure SPN 240 Volts, 50 Hz with IP-42 protection, double door with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting making good of disturbed surface complete all as specified and directed.

S&F in repair 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of two poles and current carrying capacity 63 Amp, SPN in the MCB DB complete with connection testing and commissioning, all as specified.

S&F 415V 10KA 'C' curve miniature circuit breaker MCB of following poles and current carrying capacity TPN 100 Amp in the DB complete with connection testing and commissioning, all as specified.

S&F in repair 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of 6 Amps to 32 Amps and current carrying capacity , in the MCB DB complete with connection testing and commissioning, all as specified.

S&F in repair 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of SPN 32 Amps current carrying capacity in the MCB DB complete with connection testing and commissioning, all as specified.

S&F in repair TPN DB 4 way sheet metal enclosure TPN 450 Volts, 50 Hz with IP-42 protection, double door with 200 Amps standard bus bar of suitable size and common neutral ling all enclosed in standard sheet flush mounting complete all as specified.

S&F in repair LED bulb thread/pin type of capacity 10 watt complete all as specified and directed.

S&F LED lamp 15 Watt complete all as specified.

S&F LED luminaire 600mm x 600mm, 35/36 Watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

S&F 15W LED panel round/ square type, slim, compact, aluminium die cast edge LT panel, recess mounted round fixture with opal diffuser and separate electronic driver including connecting cable of suitable size complete all as specified and directed by Engr-in-Charge.

S&F LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose all as specified and directed.

S&F LED light fitting 1x9W/1x20W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-Charge.

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m complete all as specified.

M&L for supply and fixing 1100 Volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connection suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, with two single core cables flat or circulate 16sqmm 2 core, all as specified.

M&L in repairs for earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanized earth wire of 4 mm dia (up to 7.5 m in length from earth plate ) by means of bolts and nuts checknuts and washers of galvanized iron or steel all as specified and shown in electrical plate no.3 of SSR part I including necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40 mm thick cover with MS rod 8mm dia at 150mm c/c in both ways as reinforcement, watering funnel, 20 mm dia light grade for protection of earth electrode, 20 mm dia GI pipe light grade for watering complete all as specified and as directed by Engineer in charge and tested on completion complete, all as specified. Note : The rate is inclusive of necessary earth work, RFR and removal etc.

M&L sub main wiring with two run single core 6 Sqmm FRLS copper conductor cable PVC insulated, unsheathed, 1100 V including 20 mm dia casing capping, medium grade ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall alongwith one run of 6 Sqmm single core PVC FRLS insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion etc complete all as specified and directed. Note: Two runs of 6 sqmm and one run of 6 sqmm cable and one run of casing capping shall be measured as one RM

M&L sub main wiring with two run single core 4 Sqmm FRLS copper conductor cable PVC insulated, unsheathed, 1100 V including 20 mm dia casing capping, medium grade ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall alongwith one run of 4 Sqmm single core PVC FRLS insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion etc complete all as specified and directed. Note: Two runs of 4 sqmm and one run of 4 sqmm cable and one run of casing capping shall be measured as one RM

M/S Manzoor and Co (BID ID -3495287)