Providing public health services to 100 bedded sports hostel

Amount

Providing and fixing Water Closet squatting Pan (Indian Type WC pan) Orissa pattern white vitreous china WC pan of size 580x440mm with integral type foot rests (Hindware/Parryware/Cera) with 100mm C.I P or S Trap, including cost of Cement concrete 1:2:4 platform, 10 ltr. low level PVC flushing cistern (Hindware/Parryware/Cera) with manually controlled device (Handle Lever) with all fittings, C.P brass angle valve ( Parko / Chilli / Jainco), brackets etc. 32 mm flush pipe with fittings, PVC Connection pipe 15mm nominal bore and 45 to 60cm long complete job including painting of fittings and brackets, cutting and making good the walls and floor wherever necessary.

P&F white vitreous china pedestal type (European type/wash down type) water closet pan (Parry ware/Hindware/Cera) including providing & fixing solid plastic seat with lid (white colour) and providing and fixing low level PVC flushing cistern with manually controlled device (handle lever) conf. to IS:7231 (Parryware /Hindware/Cera) 10 Liter Capacity-White in colour fitted with unplasticised PVC connection pipe 15mm nominal bore, brass end union 45 to 60cm length, G.I Inlet connection for flush pipe connecting WC pan, C.P brass angle valve (02 Nos.) 15mm nominal bore (Parko / Chilli / Jainco), C.P Jet (heavy duty) with PVC connection pipe to be fixed with European Type W.C complete job. Nothing extra shall be paid.

Providing and fixing of White vitreous China wash basin (Make Hindware/Parryware/Cera) of size 550x400/550x450 mm with 15mm C.P brass pillar cock ( Parko / Chilli / Jainco), 32mm C.P brass waste coupling , PVC Waste pipe, C.P brass angle valve ( Parko / Chilli / Jainco), Unplasticised PVC connection pipe 15mm nominal bore, brass end union 45 to 60cm length complete job including making good the wall and floor in all respects.

P&F of White vitreous China pedestal for washbasins completely recessed at the back for the reception of pipes & fittings (Make Parryware/Hindware/Cera).

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of sizes 580 x 380 x 350mm / 590 x 375 x 390mm and respectively with CP brass angle valve ( Parko / Chilli / Jainco) M.S brackets, standard flush pipes, and C.P brass spreaders with brass unions and Clamps complete job including painting of fittings and brackets, cutting and making good the walls and floors wherever required.

Providing and fixing white vitreous china urinal partition of size 755x165x365mm (Make Hindware/Parryware/Cera)

Providing and fixing 600 x 450mm bevelled edge mirror of superior glass (of approved quality) Complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminum angle frame with C.P. brass brackets and guard rail complete fixed with 40mm long screws, rawl plugs, etc. complete.

Providing and fixing soil waste and vent pipes Sand cast Iron S&S pipe as per IS: 1729 including cutting chases and making good the same wherever required. 100 mm dia

---------------do--------------- 75 mm dia

Providing and fixing plain bend of required degree.Sand cast iron S&S as per IS: 1729. 100 mm

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3mm thick, bolts & nuts complete.Sand cast iron S&S as per IS: 1729. 100 x100x100mm

--------------do--------------- 75 x75x75mm

Providing and fixing single equal junction with access door of required degree with access door, insertion rubber washer 3mm thick, bolts & nuts complete.Sand cast iron S&S as per IS: 1729. 100 x100x100mm

-----------------do-------------- 75 x75x75mm

Providing and fixing Collar: Sand cast iron S&S as per IS: 1729. 100mm

P&F Cowl/Terminal Guard Sand cast iron S&S as per IS: 1729. 100 mm

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete:100 mm dia. Sand cast iron S&S as per IS: 1729

Providing and fixing Sand cast Iron trap of self cleansing design with screwed down or hinged grating (including the cost of floor trap) with or without vent arm complete including encasing the floor trap with cement concrete (1:2:4), 150 mm thick all around. 100mm inlet and 100 mm outlet

-----------do--------------------- 100mm inlet and 75 mm outlet

P&F lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of:- 100mm dia

-------------do------------------ 75mm dia

Cutting holes in brick masonry walls/RCC roof for passing pipes (C.I/G.I/P.V.C) upto 150mm dia and making good the same with Brick masonry 1:4/RCC 1:1½:3 as required.

Providing and fixing PTMT soap dish of standard size and quality (Prayag make).

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality colour and make (Prayag Make) 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190 gms.

Providing and fixing M.S. holder bat clamp of approved design to sand cast iron/cast (spun) pipes comprising of M.S. flat brackets made of 50x5mm flat of specified shape, projecting 75mm outside the wall surface and fixed on wall with 4 Nos. 6mm dia expansion hold fasteners including drilling necessary holes in brick wall / CC / RCC surface and the cost of bolts etc. The pipes shall be fixed to the already fixed brackets with the help of 30mm x 1.6mm galvanised M.S. flats of specified shape and of total length 420mm and shall be fixed with M.S. nuts, bolts and washers of size 25x6mm, one bolt on each side of the pipe. Total brackets length 580mm of approved shape and design (for single 110mm dia pipe).

Providing and fixing G.I. pipes (medium grades) complete with G.I. fitting and clamps, including cutting chases and making good the walls etc. wherever required (Make Parkash Surya/Jindal). 15mm dia nominal bore

-------------------do------------------ 20mm dia nominal bore

-------------------do----------------- 25mm dia nominal bore

-------------------do----------------- 32mm dia nominal bore

--------------------do----------------- 50mm dia nominal bore

Providing and fixing ball valve (brass) of approved quality complete. With Handle. 15mm dia nominal bore

--------------------do------------------ 20mm dia nominal bore

-------------------do-------------------- 25mm dia nominal bore

--------------------do-------------------- 32mm dia nominal bore

--------------------do---------------------- 50mm dia nominal bore

Providing and placing on terrace (at all floors levels) polyethylene water storage tank ISI: 12701 marked indicating the BIS License no. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fitting and base support for tank [Sintex/Star having valid ISI license].

Providing and fixing C.P. brass bib cock Parko / Chilli / Jainco make complete in all respects.

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS:8931a) 15 mm nominal bore (Parko / Chilli / Jainco)

Constructing brick masonry manhole in cement mortar 1:4 (1 cement: 4 coarse sand) RCC top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) foundation concrete 1:4:8 (1 cement: 4 coarse sand: 8 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement: 3 coarse sand) 12mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded crushed stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design:- With F.P.S. bricks with class designation 75 Inside size 90x80cm and 60cm deep including fixing Angle iron frame 65x65x6mm with hold fast and covered with precast RCC Manhole cover 1:2:4 of required size including cost of reinforcement as required.

Providing and laying PVC pipes 10 kg/cm2 pressure including all PVC fittings (bend, collar, tee) jointing with adhesive (For Sewer Line) including trenching (Earthwork) and refilling etc. complete. (Uniplas/Supreme/Finolex make) Nothing extra shall be paid. 200mm dia

----------------do--------------- 150mm dia

P&F Water motor 2 H.P (Crompton/Servo Make)

Providing and fixing G.I. Tank nipple size 1" to 2" for connection complete in all respects.

P&F of Check Valve for motor 32mm nominal bore of approved quality.

Providing anf fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./H.P.H.D. plastic ball (Prayag Make) 15mm nominal bore, 105mm long, weighing not less than 138 gm.

P&F C.P Grating of 100mm dia

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931a) 15 mm nominal bore

P/F of C.P shower rose with 15/20 mm inlet including rod with necessary plugs and screws.100 mm dia

P/F of unplasticised PVC connection pipe with bass union 45 cm length & 15 mm nom. bore.

P& F CP jet with PVC pipe to be fixed with WC

M/S PAWAN KUMAR CONTRACTOR

M/S KAMA DEV SAMAL