PROVN OF ADDN ALTRN TO BLDG NO P-21 OF 3 SIKH LI PROVN OF ROOF TREATMENT AND ADDN AND ALTN FOR BLDG NO P-28 OF 3 SIKH LI PROVN OF WATER SUPPLY TO KITCHEN OF CERTAIN BUILDINGS AND DIRECT WATER SUPPLY TO BATH ROOM OF MD ACCN AT MIL STN BIKANER.

Amount

Demolition of lime concrete of any description over roof Slab complete all as specified and as directed by Engr-in-charge.

Taking down cement plaster on brick or conc surfaces including racking out joints hacking for key, scrubbing down with water etc.

Demolition of cement concrete of any description and in any position not otherwise provided for complete all as specified and directed.

Demolition of brick or stone masonary including all necessary arches, pillars, quions etc built in cement mortar.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size exceeding 1.5 Sqm and not exc 4 Sqm complete all as specified and as directed by Engineer-in-Charge

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size n. exc 1.5 Sq m each complete all as specified and as directed by Engineer-in-Charge.

Taking up or down steel tubing and connections, 15 mm bore fixed on walls, floors or ceiling etc complete all as specified and as directed by Engineer-in-Charge

Taking up or down steel tubing and connections, 20 mm bore fixed on walls, floors or ceiling etc complete all as specified and as directed by Engineer-in-Charge

Taking down eaves gutters and rain water pipes ( any size or pattern ) including all fitting heads ,shoes ,bend, swan neck etc including cleaning or re fixing or removal to store etc complete all as specified and as directed by Engineer-in-Charge

Dismantling water tank capacity exc 500 ltr but n.exc 1000 ltr complete all as specified and as directed by Engineer-in-Charge

Cutting opening through brickwalls for door, windows and other openings or enlarging existing openings etc or cutting out defective masonary for underpinning including providing fixing and removing, shoring cleaning and stacking stone and removing surplus to store and rubbish off the premises in cement mortar etc.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-Charge.

Returning, filling in approved soft/loose soil including spreading, leveling, watering and well ramming in layers each n.exc 25cm complete all as specified and as directed by Engineer-in-Charge.

Removing surplus soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed by Engineer-in-Charge.

M&L for Plain cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregate as in mass filling and foundation complete, all as specified and as directed by the Engineer -in-Charge.

M&L 40mm thick damp proof course in PCC 1:2:4 type B-O (using 12.50mm graded stone aggregate) horizontal or vertical surface, including necessary form work complete all as specified and as directed by Engineer-in-Charge.

M&L for brickwork old size with fly ash bricks straight or curved on plan exc 6 metre mean radius built in cement & sand mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

M&L for Brickwork old size with fly ash bricks straight or curved on plan exc 6 metre mean radius as in half brick walls built in cement & sand mortar 1:4 complete all as specified and as directed by Engineer-in-Charge.

M&L for TMT reinforcement bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed by Engineer-in-Charge.

Ditto- all as per Srl item No 20.00 here-in-before but 6 mm dia and over upto and including 8 mm dia as in stirrups, spacers and binders complete all as specified and as directed by Engineer -in-Charge.

M&L for reinforced cement conc M-20 Design mix as in bands, lintel beams , canyilevers over span 1.5m landings , balconies etc. incl all necessary form workcomplete all as specified and as directed by Engineer -in-Charge.

M&L for Jodhpur stone roof slab, self faced 7.5 cm to 10 cm thick, 25 cm to 35 cm wide ,hoisted set, jointed and grouted in cement and sand mortar 1:6 and pointed ceiling in cement and sand mortar 1:3 , complete all as specified and as directed by Engineer-in-Charge by Engineer-in-Charge

M&L for Flush pointing to brick laid flat or brick tile in paving , surface , channels , roof etc in cement and sand mortar 1:3 complete all as specified & directed

M&L for 10 mm thick sceeding in cement mortar 1: 4 on roof/concrete surfaces, finished Fair & even including mixing water proofing compound as per manufacturer's instns( WPC to be measured separately as supply only)

Supply only integral liquid water proofing compound, ISI marked, complete all as specified and as directed by Engineer-in-Charge

M&L for 150 micron thick polythene film black complete all as specified and as directed by Engineer-in-Charge.

Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.20 Kg per sq m including cleaning surfaces complete all as specified and as directed by Engineer-in-Charge .

M&L Lime concrete terracing as in roof complete all as specified. Note :- For lime concrete, mudia kankar (source : NAL) and Kolayat coarse sand in lieu of brick aggregates and Surkhi respectively as specified in MES schedule Part-I shall be used.

M&L for 40 mm thick Brick tiles bedded in 15 mm thick cement and sand mortar (1:6) and joints grouted flush in cement and sand mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and as directed by Engineer-in-Charge.

M&L for Plain cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) in lintel, cill, bed block coping ,bed plate, bond stone etc including weathering slightly rounded or chamfered angles and throating complete all as specified and as directed by Engineer-in-Charge

M&L for Rendering 15 mm thick plaster in cement and sand mortar 1:4, mixed with water proofing compound as per manufacturer’s instructions, on cement concrete surfaces including finishing the surface even and fair complete all as specified and as directed by Engineer-in-Charge Note :- Supply only of integral liquid water proofing compound shall be measured and paid for separately under appropriate item of this schedule).

M&L for Rendering 15 mm thick in cement and sand mortar 1:6 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge

M&L for rendering 10 mm thick in cement and sand mortar 1:3 on fair faces of ceiling including finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L for 75mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in sub base of floors including finishing the top surface of concrete even and rough complete all as specified and as directed by Engineer-in-Charge.

M&L Plain 25 mm thick PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate as in floor finishes complete all as specified and as directed by Engineer-in-Charge.

M&L for Non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but n. exceeding 0.18 sqm in floor etc, set and jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles over and including 15 mm thick screed bed in cement and sand mortar 1:6, complete all as specified and as directed by Engineer-in-Charge.

M&L for 10mm thick cement mortar rendering in cement mortar 1:3 as on vertical surfaces of wall for reciving tiles complete all as specified complete all as specified and as directed by Engineer-in -Charge.

M&L for Glazed ceramic tiles (coloured) of size 350x250x7mm / 450x350x7 mm thick on vertical surfaces such as skirting, dados etc, tile should be matched with existing tile complete all as specified and as directed by Engineer-in-Charge.

S&F factory made mild steel Window box type with upper top hung shutters and bottom fixed type shutters including pintol hinges,steel peg stay and one shop coat of red oxide primer complete all specified. Note : i) The window shall be fabricated as per Drg No CEBTZ/TD/888R & 889 ii) MS fillets, glazing, wire gauge shall be measured and paid separately iii) opening incl provn shutter for cooler to be provided

S&F 3 mm sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and as directed by Engineer-in-Charge

S&F Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed by Engineer-in-Charge

M&L for PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in hold fast, ,filling of pressed steel frame ,coping etc including necessary use and waste of formwork complete all as specified and as directed by Engineer-in -Charge.

S&F PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, including cutting holes in brick walls for inserting hold fasts and making good dismantled portion in CM (1:3) or cement concrete (1:2:4) type B1 as required complete all as specified and as directed by Engineer-in-Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing complete all as shown in drawing of relevant item in MES Schedule Part-II (2010 Print), complete all as specified and as directed by Engineer-in-Charge.

S&F 100 mm long Butt hinges extruded aluminium alloy , with galvanised mild steel hinge pin, anodised, type B-21, ISI marked complete all as specified and as directed by Engineer-in-Charge

S&F Aluminium handles, fabricated type, anodised of 150 mm size, ISI marked, complete all as specified and as directed by Engineer-in-Charge.

S&F 150 mm long, aluminium anodised, barrel tower bolts, of extruded section, ISI marked, complete all as specified and as directed by Engineer-in-Charge.

S&F Steel 100 mm locking bolts with mild steel electrogalvanised plate and bright bolt not less than 10mm dia, 100mm size complete all as specified and as directed by Engineer-in-Charge.

S&F 20 mm MS drapery rod powdered coated wooden finish as directed and approved by G E

S&F curtain rod holders (Twin finish) wooden finish made up of wood with screws for tightening rods and brackets shall be polished complete all as specified and as directed by Engineer-in-Charge.

M&L for 15 mm bore tubes, medium grade, galvanized with and including all fittings fixed to walls, floors or ceiling or laid in trenches.etc complete all as specified and as directed by Engineer-in-Charge.

M&L for 20 mm bore tubes, medium grade, galvanized with and including all fittings fixed to walls, floors or ceiling or laid in trenches.etc complete all as specified and as directed by Engineer-in-Charge.

M&L for Vitreous China wash down water closet pan ( pedestal pattern), white, (excluding flushing cistern and flush pipe) but including CI ‘P’ trap and also including connection to drain (or outgoing pipe) and to flushing pipe, anti- syphonage pipe etc, supplied and fixed in repairs, complete all as specified and as directed by Engineer-in-Charge. (Note for SI No here-in-before :- (i) WC shall be ISI marked, 1st quality and of makes specified in Appendix ‘D’ (ii) Unit rate quoted shall also be deemed to include for provision of lead joint between CI trap and outlet pipe (iii) Unit rate quoted shall also be deemed to include for labour required for fixing of flushing cistern and flush pipe and also for taking down old flushing cistern and flush pipe. Supply only of flushing cistern with flush pipe shall be measured and paid for separately. (iv) The disturbed surface of floor shall be made good as per existing specification without any extra cost to the Govt).

Supply only PVC low level flushing cistern, valve less, symphonic action type, 10 litres capacity with inlet, ball valve, float and handle with and including brackets & PVC bend pipe 90 cm long etc, with and including flush pipe complete all as specified and as directed by Engineer-in-Charge(Note :- (i) Flushing cistern shall be ISI marked, Ist quality and of make as specified in Appendix ‘D’. Labour required for fixing of flushing cistern and flush pipe and also for taking down old flushing cistern and flush pipe shall be deemed to be included in the unit rate quoted for WC ).

S&F PVC seat jet with hinges and delivery pipe etc complete all as specified and as directed by Engineer-in-Charge.

S&F Vitreous china wash basin, white, flat back, size 550 x 400mm with and including a pair of CI brackets, etc, supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge.(Notes : -(i) The wash basins shall be ISI marked, 1st quality and shall be of Make as per Appendix ‘D’ (ii) The rate quoted shall be deemed to include for taking down old WHB complete with all fittings including cutting holes for taking out old brackets and supplying and fixing new WHB with new C.I brackets and also PCC blocks of PCC 1:2:4 type B-1 of size 10cm x 7.5cm x 15 cm for fixing brackets and also including new screws, plugs, cement mortar, red lead cement and other subsidiary materials required for fixing. (iii) The rate quoted shall also be deemed to include for fixing only of CP brass mixer and waste pipe with coupling. Supply only of CP brass mixer and waste pipe shall be measured and paid for separately under appropriate items of this schedule).

S&F 32 mm size waste coupling of CP (half or full threaded) Minimum weight 32mm-45gms/40mm-60 gms)

S&F 15mm bore centre hole Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed with round spout with 450mm long copper pipes and brass nuts with out Pop up M complete all as specified and as directed by Engineer-in-Charge.

S&F Bib tap, cast copper alloy chromium plated fancy type, crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, for bore of pipe 15mm, supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge

S&F in repair Brass chromium plated shower rose (ISI marked) 125mm size with or without swivel joints , including fixing to steel pipe or union, supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

S&F stop valves, cast copper alloy, fancy type, chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, for bore dia of pipe 15 mm, supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

S&F chromium plated toilet paper holder complete all as specified and as directed by Engineer-in-Charge.

S&F Glass shelf with chromium plated guard rails complete all as specified and as directed by Engineer-in-Charge.

S&F Tubular towel rail of aluminium anodised , 20 mm dia , 600mm long between flanges , D type fixed with and including chromium plated brass screws and wooden/plastic cleats supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

S&F Stainless steel soap dish holder as approved by GE complete all as specified and as directed by Engineer-in-Charge.

S&F stainless steel Peg set of six, hat and coat hooks, solid body, not less than 300 mm long complete all as specified and as directed by Engineer-in-Chargecomplete all as specified & directed by Engineer-in-charge

S&F corner glass shelf small Make CERA Cat No F5005101 and equivalent.

Rotational moulded polyethylene water storage tanks of 500 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc complete all as specified and as directed by Engineer-in-Charge.

M&L Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc complete all as specified and as directed by Engineer-in-Charge. ( Notes for Sl item No.70 &71 : (i) The water storage tanks shall be two layered & ISI marked, HDPE tanks moulded to seam-less perfection of rotational moulding process. The tanks shall be manufactured only from FDA approved special grade of polyethylene and shall be certified fit for potable water. Also refer paras 18.60 and 18.60 A of MES Schedule Part-I. (iii) Payment for inlet, outlet and over flow pipes and ball valve 20 mm bore shall be made separately. However cost of providing necessary GI fittings such as nipples with check nuts for inlet and outlet pipes, GI plug with check nut for over flow pipe and 30 cm long wash out pipe, GI 20mm nominal bore, medium grade and check nut for wash out pipes of size as per actual requirements and as directed by the Engineer-in-Charge shall be deemed to be included in the unit rate of this item.(iv) HDPE storage tanks shall be procured from the manufacturers as per Appendix “D”.)

S&F for 20mm bore ball brass valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe with or brass ferrule supplied and fixed in repairs complete all as directed by Engineer-in-Charge.

M&L for 110 mm bore, PVC (SWR) pipes as in rain water pipe, single socketed, in any length, with rubber ring joints, fixed to walls including requisite number of clamps made of flat iron 25x4 mm complete all as specified and as directed by Engineer-in-Charge.

M&L for PVC (SWR) bend for 110 mm bore pipe, any radius including jointing with solvent cement complete all as specified and as directed by Engineer-in-Charge.

M&L 110 mm bore, PVC (SWR) pipes, single socketed, in any length, with rubber ring joints, laid in trenches or in floor complete all as specified and as directed by Engineer-in-Charge

S & F in repair PVC (SWR) 'P' & 'S' trap 125/110mm setting and jointed with solvent cement etc. complete all as specified and as directed by Engineer-in-Charge.

M&L for 75 mm bore, PVC (SWR) pipes, single socketed, in any length, with rubber ring joints, laid in trenches or in floor complete all as specified and as directed by Engineer-in-Charge

M&L for PVC (SWR) gully trap 125/110 mm setting and jointing with solvent cement supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge

M&L for 75 mm bore, PVC (SWR) pipes as in rain water pipe, single socketed, in any length, with rubber ring joints, fixed to walls including requisite number of clamps made of flat iron 25x4 mm complete all as specified and as directed by Engineer-in-Charge.

M&L for 75 mm dia bore PVC (SWR) vent cowl fixed in position to vent pipe complete all as specified and as directed by Engineer-in-Charge

S&F PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement complete all as specified and as directed by Engineer-in-Charge.

M&L for PVC (SWR) bend for 110 mm bore pipe, any radius including jointing with solvent cement complete all as specified and as directed by Engineer-in-Charge.

S&F PVC (SWR) junction single ( single T) equal or unequal for 110 mm bore pipe with provided access door complete all as specified and as directed by Engineer-in-Charge.

S&F 110 mm bore PVC (SWR) couplers complete all as specified and as directed by Engineer-in-Charge.

S&F PVC (SWR) reducer for 110 mm to 75 mm bore , jointed with solvent cement complete all as specified and as directed by Engineer-in-Charge.

S&F stack clamps out of 100mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to walls for 50 mm bore pipe complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of old or new surfaces of walls by removing existing treatment completely rougheniing the surfaces and applying a thin layer of Birla white putty to give uniform surface applying coat of oil bound distamper on walls old/new decorated surfaces of desired finish as app by Eng-in-charge

M&L for preparation of old or new surfaces of walls by removing existing treatment completely rougheniing the surfaces and applying a thin layer of Birla white putty to give uniform surface applying coat of oil bound distamper on ceiling old/new decorated surfaces of desired finish as app by Eng-in-charge in any position

M&L for prep of old or new surfaces of walls by removing existing treatment completely rougheniing the surfacestwo coats of cement based paint /weather proof exterior paint any color on any type of plastered surfaces including facias.

M&L Painting to new steel surfaces of any description not otherwise described over 10 cm in width or girth including preparation of surfaces, priming with red oxide zinc chrome primer (one coat) and finishing with two coats of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge.

M&L Painting to new wood or wood based surfaces of any description, not otherwise described over 10cm width or girth including preparation of surfaces, priming with pink primer (one coat) & finishing with two coats of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge.

M&L for P:C:C 1:3:6 type D-2 using 40 mm graded stone aggregates as in beds of SGSW pipe 150 mm bore, laid to required slope including packing under and haunching against the side of pipes after they are laid and tested complete all as specified and as directed by Engineer-in-Charge Note: - (i) Thickness of concrete bed below the barrel of pipe shall be 10cm. (ii) Pipe shall be measured & paid for separately. (iii) Width of concrete bed shall be equal to outer dia of drain pipes (not of sockets/collars) plus 30cm. (iv) The rate includes for all necessary shuttering and support to concrete and for laying beds to falls.

S&F 150 mm bore (internal diameter) salt glazed stone ware drain pipes laid in trenches on concrete bed to slopes, jointing and testing including fittings complete all as specified by Engineer-in-Charge. Note :- As these pipes are to be laid in already excavated trenches for demolition of existing pipes including demolition of bedding and hunching, excavation for these pipes shall not be measured separately.)

M&L for brick work in cement mortar (1:4) using old size sub class 'B' bricks in walling, straight or curved on plan exc 6m mean radius all as specified.

M&L Precast reinforced cement concrete 1:2:4 type B-1,using 20 mm graded aggregate as in manhole covers base slab ,baffle wall and similar articles with plain faces including necessary moulds and setting in cement and sand mortar 1:4 etc including necessary use and waste of form work complete all as specified and as directed by Engineer-in-Charge. Note :- Reinforcement shall be measured and paid for separately under appropriate items of this schedule).

M&L for Extra for forming fair finished drain or channel 30 cm girth in cement concrete , using extra cement including forms, moulds, mitered/stopped ends etc complete all as specified and as directed by Engineer-in -Charge.

Demolition of cement concrete (un-reinforced) in ground floors and paving n.exc 15 cm thickness (below or above GL) complete all as specified and as directed by Engineer-in-Charge.

Dismantling of cast iron or PVC pipe 100 mm bore dia, jointed in cement mortar and taking out of trenches, if required complete all as specified and as directed by Engineer-in-Charge.

Dismantling water tank capacity exc 500 ltr but n.exc 1000 ltr complete all as specified and as directed by Engineer-in-Charge.

Roughening surface of old concrete floor by picking sweeping clean and washing down with water to remove dust etc complete all as specified and as directed by Engineer-in-Charge

M&L for Brickwork with fly ash bricks straight or curved on plan exc 6 metre mean radius as in half brick walls built in cement & sand mortar 1:4 complete all as specified and as directed by Engineer-in-Charge.

M&L for 15 mm thick screed bed or a layer of bedding for laying of floor finishes in cement and sand mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

M&L for Rendering 5 mm thick in cement and sand mortar 1:3 on fair faces of ceiling including finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L for 20-25 mm thick machine cut kota stone slab as in flooring laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by Engineer-in-Charge. (Size of Kota Stone slab shall be 55 cm x 55 cm)

M&L for 20-25 mm thick machine cut kota stone slab on vertical surfaces/riser of step/ skirting etc laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and as directed by Engineer-in-Charge. (Length of Kota Stone slab shall be such that it matches with the size of stone slab in flooring and the width as directed)

M&L for White marble strip 20 mm thick and 100 mm wide white marble strip, machine cut, bedded jointed and pointed with white cement slurry including cutting , grinding and polishing etc complete all as specified and as directed by Engineer-in-Charge.

M&L for Moulding of kota/marble/granite stone full round complete all as specified and as directed by Engineer-in-Charge.

M&L for Non skid joint free coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but n. exceeding 0.18 sqm in floor etc, set and jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles , complete all as specified and as directed by Engineer-in-Charge.

M&L for Non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but n. exceeding 0.38 sqm in skirting/dado etc, , complete all as specified and as directed by Engineer-in-Charge

M&L for 20 mm thick machine cut Black granite stone slab work ( table rubbed and polished) in step, jambs, pillars , window cill, in cooking platform, including pointing in white cement 1:2 using marble dust with admixture of pigment to match with marble shade, and also including rounding of front/outer edges laid over and including 20 mm thick cement screed in cement morter 1:6, complete all as specified and as directed by Engineer-in-Charge

M&L for Hardcore of broken stone or boulders of gauge not exceeding 63 mm, deposited, spread and leveled in layers not exceeding 15 cm thick, watered and rolled to a true surface complete all as specified and as directed by Engineer-in -Charge.

M&L for 75 mm thick PCC (1:3:6) type C-1 using 20mm graded stone aggregate laid in bays including finishing the top surface of concrete even and smooth, without using extra cement as in plinth protection laid to slope of 1 in 12 and finishing cement concrete surface even and smooth without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounded or chamfering of exposed edges where directed and providing 6 mm thick joint through the thickness of plinth protection duly filled with mastic filling of one part of hot bitumen 85/25 grade and three parts of fine sand(by all weight) complete all as specified and as directed by Engineer-in-Charge.

M&L for Mild steel framed work as in grills, gratings etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, framework of water tank and similar works conforming to Fe 290 Gde E-165, complete all as specified and as directed by Engineer-in-Charge.

M&L for TMT reinforcement bars 5 mm dia and overup to including 10 mm in stirrups, spaces and binder complete all as specified and as directed by Engineer-in-Charge.

M&L for RCC M-25 design mix using 20 mm graded stone aggregate as in slabs, supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by Engineer-in-Charge.

M&L for RCC 1:2:4 type B1 (Nominal mix) 20mm graded stone aggregate as in Chajjas, platform including necessary form work etc complete all as specified and as directed by Engineer-in-Charge.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thickness, for rough finished flat surfaces of concrete, complete all as specified and as directed by Engineer-in-Charge

Use and waste of Form work to edges edge of concrete flat floor and roof not exc 200 mm wide to rough finished surfaces of concrete complete all as specified and as directed by Engineer-in-Charge.

M&L for Rendering 10 mm thick plaster in cement and sand mortar 1:4, mixed with water proofing compound as per manufacturer’s instructions, on cement concrete surfaces including finishing the surface even and fair complete all as specified and as directed by Engineer-in-Charge Note :- Supply only of integral liquid water proofing compound shall be measured and paid for separately under appropriate item of this schedule).

S&F APP based polymeric membrance min weighing 3kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric and on primed surface by force application complete all as specified nd as directed by Engineer-in-Charge.

M&L Pressed steel frames of size 125mm x 60mm for double doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and as directed by Engineer-in-Charge.

S&F 35 mm thick, IInd class hard wood (Bonsum/Hollock) plain, framed, panelled factory made shutters (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm thick veneered particle board with commercial veneering on both faces. The size of rails and styles as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified & as directed by Engineer-in-Charge.

S&F 35 mm thick, IInd class hard wood (Bonsum/Hollock), glazed & skeleton factory made shutters, open rebated & prepared to receive glass, gauze etc. (without sash-bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, Section-8, clause 8.24(a) complete all as specified and as directed by Engineer-in-Charge. (Notes for Srl item Nos 21 &122 here-in-before: - 1.The contractor may use/provide Ist class hard wood “SHISHAM” for manufacturing of factory made shutters in lieu of IInd class hard wood without any extra cost to the govt.2. The shutters shall be procured from any of the approved manufacturers from the list given in particular specifications Section-II. 3. Wire clothing & glazing will be measured & paid for separately.)

S&F 150 mm size mild steel, stove enamelled black, pressed handles, fabricated type, ISI marked complete all as specified and as directed by Engineer-in-Charge.

S&F Aluminium alloy anodized sliding door bolt with hasp, staples (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast aluminium alloy length of bolt 250mm of ISI marked fixed in repair complete all as specified and directed by Engineer-in-Charge.

S(F Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring anodized with hard drawn steel fixed in floor overall length of cover plate 150 mm complete all as specified and as directed by Engineer-in-Charge.

S&F 300mm long helical door spring mild steel ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and as directed by Engineer-in-Charge

S&F 150 mm long, mild steel, barrel tower bolt, stove enameled black with bright bolt, ISI marked complete all as specified and as directed by Engineer-in-Charge.

S&F factory made mild steel Ventilator box type with upper top hung shutters and bottom fixed type shutters including pintol hinges,steel peg stay and one shop coat of red oxide primer complete all specified. Note : i) The window shall be fabricated as per Drg No CEBTZ/TD/888R & 889 ii) MS fillets, glazing, wire gauge shall be measured and paid separately

S&F 3 mm sheet glass frosted quality and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

M&L for Vitreous China squatting pan “Orissa” pattern, size 580x440mm, white, with integral foot rests (excluding flushing cistern and flush pipe), with CI ‘P’ trap of long arm of suitable size including connection to flush pipe, anti syphonage pipe etc, supplied and fixed in repairs, complete all as specified and as directed by Engineer-in-Charge. Notes :- (i) WC shall be ISI marked, 1st quality and of makes specified in Appendix ‘D’ (ii) Unit rate quoted shall also be deemed to include for provision of lead joint between CI trap and outlet pipe (iii) Unit rate quoted shall also be deemed to include for labour required for fixing of flushing cistern and flush pipe and also for taking down old flushing cistern and flush pipe. Supply only of flushing cistern with flush pipe shall be measured and paid for separately. (iv) The disturbed surface of floor shall be made good as per existing specification without any extra cost to the Govt).

S&F Vitreous China urinal half stall type flat back of size 590 mm x 375 x 390 mm white (minimum) with cp waste fitting grating and union for discharge pipe (excluding flushing cistern, flush pipe ) including urinal spreader of CP and PVC waste pipe of adequate length complete all as specified and directed by Engineer-in-Charge

S&F Pillar taps cast copper alloy, fancy type with capstan head, chromium plated, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nut, screwed for iron pipe 15 mm bore, supplied and fixed in repairs, complete all as specified and as directed by Engineer-in-Charge.

S&F Bib tap , cast copper alloy chromium plated, long body with capstan screwed down, screwed for iron pipe or for brass ferrule, for bore of pipe 15mm, supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge

S&F PVC connection 15 mm size, of length 450 mm, with PTMT nuts, fixed in repair complete all as specified and as directed by Engineer-in-Charge.

S&F Stop valves,concealed type cast copper alloy, fancy type, chromium plated with long shank and cup , screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, for bore dia of pipe 15 mm, supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

S&F 100 mm bore, cast iron, centrifugally cast, soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches complete all as specified and as directed by Engineer-in-Charge.

S&F 100 mm bore, cast iron, centrifugally cast, soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls complete all as specified and as directed by Engineer-in-Charge.

S&F 75 mm bore, cast iron, centrifugally cast, soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches complete all as specified and as directed by Engineer-in-Charge.

S&F 75 mm bore, cast iron, centrifugally cast, soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls complete all as specified and as directed by Engineer-in-Charge.

S&F 50 mm bore, cast iron, centrifugally cast, soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls complete all as specified and as directed by Engineer-in-Charge.

S&F CI cowls for 50mm bore of pipe supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

S&F 100mm bore CI bends (any radius) , diminishing pieces or tapers complete all as specified and as directed by Engineer-in-Charge.

S&F 75mm bore CI bends (any radius) , diminishing pieces or tapers complete all as specified and as directed by Engineer-in-Charge.

M&L for Extra over cast iron pipe and fittings if lead joint is provided in lieu of cement joint for 75 mm bore

M&L for Extra over cast iron pipe and fittings if lead joint is provided in lieu of cement joint for 100 mm bore

M&L 100mm bore cast iron branch pieces, single (equal or unequal),ordinary or inverted (spigot or socket type) or with parallel branches , with oval access door jointed with cement mortar complete all as specified and as directed by Engineer-in-Charge

M&L 75mm bore cast iron branch pieces, single (equal or unequal),ordinary or inverted (spigot or socket type) or with parallel branches , with oval access door jointed with cement mortar complete all as specified and as directed by Engineer-in-Charge

S & F in repair cast iron 'P' & 'S' trap 125/110mm setting and jointed with solvent cement etc. complete all as specified and as directed by Engineer-in-Charge.

Cast iron Nahani trap/ floor trap with dia of outlet 75 mm with CP grating including jointing with lead joint to waste pipe fixed in cement concrete type B1 (1:2:4) supply & fixed in repair complete all as specified and as directed by Engineer-in-Charge.

S&F stack clamps out of 100mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to walls for 75 mm bore pipe complete all as specified and as directed by Engineer-in-Charge.

S&F stack clamps out of 100mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to walls for 100 mm bore pipe complete all as specified and as directed by Engineer-in-Charge.

M&L for Plain cement concrete (1:5:10) type E-2 using 40 mm graded stone aggregate as in mass filling and foundation complete, all as specified and as directed by the Engineer -in-Charge.

M&L for Plain cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in foundation filling complete all as specified and as directed by Engineer-in-Charge.

M&L for Steel work in tubular trusses including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and as directed by Engineer-in-Charge.

M&L mild steel work as in plates/flats angles etc as in cleat drilling welding etc complete all as specified and as directed by Engineer-in-Charge.

S&F Mild steel screw bolt 11 to 15 mm dia (machine made) with hexagonal or square heads at one end screwed at other, screwed both end to be fitted with washers and one hexagonal or square nut n. exc 5 cm long complete all as specified and as directed .

S&F Mild steel screw bolt (machine made) with hexagonal or square heads at one end screwed at other, screwed both end to be fitted with washers and one hexagonal or square nut, length of bolt exc 30 cm and dia of nut exc 12 mm and not exc 20 mm complete all as specified and as directed .

S&F Mild steel Plates ( plain or chequered ) channels square cut or notched ( ordinary and counter sunk ) forming holes with riveted , bolted or welded attachment etc using rolled mild steel Fe 410-W (Gde E-250) quality ‘A’ complete, drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting) and hanging; also fastening and fixing complete all as specified and as directed by Engineer -in-Charge.

M&L for high rib profile tile pattern color coated 0.6 mm thick galvalum sheets as in roof covering and fixed as per manufacturers instruction (design as app by Engg in charge complete all as spfd )

M&L for 0.8mm thick color coated plain galvanised mild steel sheeting factory made as in ridges fixed with self driven screws complete all as specified and as directed by Engineer -in-Charge.

M&L for 75 mm thick Plain Cement concrete,1:2:4 (using 40mm graded stone aggregate) type B- 2 as in floor finished complete all as specified and as directed by Engineer-in-Charge.

Preparation of plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer as per manufacturer's instructions on walls complete all as specified and as directed by Engineer-in-charge.

Preparation of plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer as per manufacturer's instructionson ceiling complete all as specified and as directed by Engineer-in-charge.

Preparation of new plastered surfaces of walls surfaces of walls, cornices, pillasters and applying three coat of white wash complete all as specified and as directed by Engineer-in-Charge.

Preparation of old decorated surfaces of ceiling etc and applying one coat of white wash complete all as specified and as directed by Engineer-in-Charge.

Surface dressing in soft & loose soil n exc 15 cm deep complete all as specified and as directed by Engineer-in-Charge.

M&L for 60mm thick machine pressed with grey cement and no pigment interlocking factory made paver blocks of any size and shape conforming to IS 15658-2006, M-35 grade set, complete all as specified and as directed by Engineer-in-Charge.

M&L for Sand filling under floor ,cushioning under interlocking tiles or in foundations including watering and consolidation complete all as specified and as directed by Engineer-in-Charge. (Note : 1. Approved local tibba dry sand after removal of vegetations, grass and other deleterious substances shall be used for sand cushioning ).

Dismantling water tank capacity exc 250 ltr but n.exc 500 ltr complete all as specified and as directed by Engineer-in-Charge

M&L for Rendering 15 mm thick in cement and sand mortar 1:4 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge

M&L for Plain cement concrete 1:4:8 type D 2 (using 40 mm graded stone aggregate)as in foundation filling complete all as specified and as directed by Engineer-in-Charge.

Supply only integral water proofing compound, ISI marked, complete all as specified and as directed by Engineer-in-Charge

S&F 15 mm dia Gun metal gate valves with iron wheel head, screwed both ends for iron pipes complete all as specified and as directed by Engineer-in-Charge.

S&F 20 mm dia Gun metal gate valves with iron wheel head, screwed both ends for iron pipes complete all as specified and as directed by Engineer-in-Charge.

S&F PVC tank lid for 500 & 1000 ltrs capacity including all locking arrandements , nuts bolts etc for fixing complete all as spfd and directed by Eng-in-charge.

M&L Cleaning and removing all scale and dirt, etc, from tanks of capacity exc 250 &n exc 500 ltr and from mouths or circulationg pipes, etc. complete all as specified and as directed.

M&L for brick work in cement mortar (1:6) using old size sub class 'B' bricks in walling, straight or curved on plan exc 6m mean radius all as specified.

M&L for Jodhpur stone roof slab, self faced 7.5 cm to 10 cm thick,25 cm to 35 cm wide ,hoisted set, jointed and grouted in cement and sand mortar 1:6 and pointed ceiling in cement and sand mortar 1:3 , complete all as specified and as directed by Engineer-in-Charge by Engineer-in-Charge

S&F Supply only CP flush pipe 32mm bore for low level cistern incl all as specified and as directed.

S&F Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, for 15mm bore GI pipe , supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

S&F 15mm bore stop cock cast copper alloy screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule.

S&F Grating doom 125 mm with waste hole of PTMT incl all arrangements and as specified.

S&F 15mm bore angular stop cock with wall flange as specified and as directed

S&F 75mm dia cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

S&F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to walls for 100mm bore pipe

S&F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to walls for 75mm bore pipe

S&F CI cowls for 50mm bore of pipe supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge

Preparation of new plastered or un plastered surfaces of wall and applying two coats of cement base paint white or tinted over a coat of alkali resistant priming coat complete all as specified and as directed by Engineer-in-charge

Preparation of new plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer as per manufacturer's instructions on walls complete all as specified and as directed by Engineer-in-charge.

Taking down carefully existing unserviceable batten/surface conduit/ concealed conduit aluminium point wiring (light, fan, bell/buzzer, socket or power) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, pendents, sockets, lamp holders, shades, fan regulators, light fittings, bells etc including sunken boxes and removing the retrieved materials from dismantling including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and as directed by the Engineer-in-Charge.

Taking down of unserviceable DBs/switch fuses/changeover in sheet steel enclosure complete with MCBs/fuse/grip any capacity and removing from site and making good disturbed surface of wall , floor etc taking after disconnecting all cable complete all as specified and as directed by Engineer-in-Charge.

Point wiring with multi stranded copper conductor cable, 1100 volts grade (ISI marked), , PVC insulated and unsheathed of size 1.5 sqmm, single core in and including new non metallic rigid PVC concealed conduit of 20 mm dia, medium duty, ISI marked, including conduit fittings such as tees, bends etc terminating in M.S sunken boxes covered with and including 3 mm thick bakelite laminated sheet top cover of approved make for mounting switches, sockets, regulators etc,with and including continuous 1.5 sqmm PVC insulated unsheathed single core copper conductor cable as earth continuity conductor connected to common earth and earth dolly, for one light point/fan point/ call bell point controlled by one, one way switch complete all as specified and as directed by Engineer-in-Charge.

All as per SI No 194.00 here-in-before but 3pin 5 Amp sockets points on the same board with other switches complete all as specified and as directed by Engineer-in-Charge.

All as per SI No 194.00 here-in-before but 3 pin 5 Amp sockets points on the independent board with other switches complete all as specified and as directed by Engineer-in-Charge.

Ditto- all as per SI No 194.00 here-in-before but with multi stranded copper conductor FRLS cable, 1100 volts grade (ISI marked), PVC insulated and unsheathed of size 2.5 Sqmm single core and with and including 1.5 Sqmm PVC insulated unsheathed single core copper conductor cable as earth continuity conductor to common earth and earth dolly for one 15 Amp socket outlet point on the independent board complete all as specified and as directed by Engineer-in-Charge.

S&F Switch piano flush type , single pole 5 Amps, one way, ISI marked complete all as specified and as directed by Engineer-in-Charge

S&F Ceiling rose, three terminal, PVC/Poly carbonate, insulated body three terminal , ISI marked, complete all as specified and as directed by Engineer-in-Charge.

S&F Socket outlet 3 pin 5 amp flush type, ISI marked complete all as specified and as directed by Engineer-in-Charge.

S&F Lamp holder insulated body with back plate suitable for concealed conduit/casing caping/batten fittings complete all as specified and as directed by Engineer-in-Charge.

S&F Decorative Ultra slim linear energy efficient LED lightening fixture, Eco friendly efficient 18/20 Watt with extruded aluminium complete all as specified.

Supply and fixing sheet metal enclosures for DB, SPN 8 way, 240 Volt, Double door, IP-43 protection, IK-09 with metal door with 200 Amps copper bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar complete all as specified and as directed by Engineer-in-Charge.

S&F MCB suitable for 06 to 32 Amps, 240 Volt AC supply single pole and neutral with over load and short circuit protection having rupturing capacity not less than 10 KA complete all as specified and as directed by Engineer-in-Charge.

MCB single pole of rating 06 to 32 Amps 10 KA, ‘C’ curve 240 V AC complete all as specified and as directed by Engineer-in-Charge

Earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of plate not less than 1.5 deep below normal ground level and connected to and including galvanized earth lead wire 4mm dia upto 7.5 metre by means of GI nuts, bolt, check nuts, washers thimbles, etc as shown in electrical plate No 03 SSR Part I and connection to main switch board or panel and testing on completion including excavation and earth work in any type to soil, returning fitting in and removal of surface spoil to a distance not exc 50 metre, PCC chamber (1:3:6) type C-2, charcoal and salt mixed layer 15cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe light grade 20mm bore for watering and 15mm bore meter long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25mm x 3mm, bolts, nuts and washers 75mm thick RCC cover 1:2:4 type B-1 shall be provided on CI frame etc complete all as specified. Note - PCC chamber shall be constructed at least 1.5m away from the earth electrode. The pipe for watering shall be provided in slanting manner

M&L Making of hole in wall for fixing of exhaust fan of size 300mm sweep with necessary nuts, bolts and making the good of disturbed surface of wall and matching with existing surface complete all as specified and directed by Engr-in-charge.

S&F Exhaust fan 225 mm sweep with louvers including making of holes and making good the disturbed surface of wall including slandered copper flexible twin core cable of size 23/0.0076 supplied fixed in repair complete all as specified and as directed by Engineer in charge. Note:- . (i) contractor will write MES No as per specified and directed.

Supplying and laying XLPE insulated screened, PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) with , aluminium conductor, 1100 volts grade of cross sectional area 6 Sqmm 2 core laid in trenches/through pipe in road crossings/paths /drains /ducts/floors/along poles/walls/ceilings/equipments etc complete all as specified and as directed by Engineer-in-charge

M&L for Protection to cable with one layer of bricks laid flat butting to each other in such a way that the length of the bricks is at right angles to the central axis of the cable using old size sub-class ‘B’ burnt clay bricks complete all as specified and as directed by Engineer-in-Charge.

M&L for Sand cushioning and cover (using local tibba sand), 80 mm thick before laying of cable and 150 mm thick after the cable is laid, complete all as specified and as directed by Engineer-in-Charge. (Note : 1. Approved local tibba dry sand after removal of vegetations, grass and other deleterious substances shall be used for sand cushioning and cover).

M&L for 40 mm bore GI tube, light grade for protection of cable , with all fitting lead in trenches /under road / with wall /in wall /under floor where required complete all as specified and as directed by Engineer-in-Charge.

S&F Switch piano flush type , single pole 15 Amps, one way, ISI marked complete all as specified and as directed by Engineer-in-Charge

S&F socket outlet 3 pin 15 amp flush type, 240 Amp, ISI marked complete all as specified and as directed by Engineer-in-Charge.

S&F Fan regulator electronic type 230 Volts,150 watt with 5 step control suitable for 1200/1400 mm sweep ceiling fan, rotary type complete all as specified and as directed by Engineer-in-Charge

S&F MCB tripple pole and neutral suitable for 63 Amps, 415 Volt AC supply with over load and short circuit protection having rupturing capacity not less than 10 KA complete all as specified and as directed by Engineer-in-Charge.

Suppy and Fixing LED based security light, housing made up of LM6 pressure die cast aluminium alloy with effective thermal management, sturdiness. The fixture should have a minimum system efficiency of more than 100 lumen/watt and a minimum system lumen output of not less than 7200 lumens and maximum system wattage 25 Watts. The fixture shall have a correlated colour temperature of al least 5700K and CRI f minimum 70. The fixture shall be designed for a system life of 50,000 hours @ 70% lumen maintenance ingress protection of IP66 (lamp and gear compartment and mechanical inpact resistance raiting of IK>=08. The fixture driver should have an operating voltage range of 140-270 V & potted type for humming free operation, driver should be withstand up to 440v for 8hrs, two surge proection not less than 5KV one on driver and one external surge protection, PF>0.95 and THD<10% and have double phase protection. LED light fitting should be suitable for ambient temperature from (-) 10C to (+) 50 C. The fixture should comply with the parameters IEC 60598 and LED should comply to IEC 61000-3-2 ed. 3.2 per harmonics IEC 61347-2-3,2006 in configuration with IEC 61347-1 ed 2.0,2007 for electrical safety LM 79 and for LED LM 80 test report needs to be submitted from the house NABL accreditation laboratory. Make CG/C&S/Bajaj/Havells

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed by Engineer-in-Charge.

Hanging only ceiling fan taking down vide above item and connecting up with provn of 3 core of flexible cable of size 1.5 sqmm complete all as specified and as directed by Engr-in-charge.

Supplying and laying XLPE insulated screened, PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) with , aluminium conductor, 1100 volts grade of cross sectional area 25 Sqmm 4 core laid in trenches/through pipe in road crossings/paths /drains /ducts/floors/along poles/walls/ceilings/equipments etc complete all as specified and as directed by Engineer-in-charge

M&L for 3 mm sheet glass frosted quality and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and as directed by Engineer-in-Charge

S&F stop vale fancy hub concluded type stop valve chromium plated with long shank and complete screwed for long pipe complete all as specified.

SHREE GURU NANAK CONSTRUCTION COMPANY

ALPHA ENGINEERING COMPANY