Construction work of a Tin shrd in park opposite Padma Tent House In Bibipur Maharajpur Kanpur Nagar

e/w in surface excavation not exceeding 30 cm in depth but exceeding 1.5 mtr width as well as 10 sqmt on plan including getting out and disposal of excavated earth upto 50 mtr and lift upto 1.5 mtr as directed by engineer-in-charge 2.1.1 all kind of soil. Chaptter-4 Sr No.1 Ref to DSR/PWD 2.6(2.6.1)

p/l in position cement concrete of specified grade excluding the cost of shuttering all work upto plinth level 1:4:8 (stone aggregate 40mm nominal size) Chapter No. 5 Sl. 1 Ref to DSR/PWED 4.1.8

p/l in position cement concrete of specified grade excluding the cost of shuttering all work upto plinth level 1:2:4 (1 cement : 2 corsesand Zone III : 4 grade stone aggregate 20mm nominal size) Chapter No. 5 Sl. 1 Ref to DSR/PWED 4.1.3

Centing and shuttering including shuttering propering etc. and removal of form work for (upto 5th floor) Foundations, footing, base for columns, Chapter-5 Sl No. 3 Ref. to DSR/PWD 4.3.1

M.S (Tor steel or plain ) in plain work such as R.C.C or R.B work including cutting / bending for proper shape as necessary including supply of all steel & wastage ,bend ,hook & authorised overlapping shall be measured … complete item. (A/R)

12 mm thick cement plaster in single coat of fair side wall with 1 :4 cement & fine sand including all labours, materials, T&P etc all complete. (PWD Sch 13 SL No. 1 ref. to DSR/PWD13.1.1

S/f of MS anchor bolt with nut 20 mm dia 60cm long with hold fast .

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. DSR 10.16.1

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.D.S.R.10.2

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. D.S.R 12.50

Gutter (600 mm over all girth)

Ridges plain (500-600 mm)

Painging and varnishing on iron works in small areas or new wood work with one coat of ready mixed priming paint & one coat of approved superiod quality ready mixed paint of clear synthetic varnish including supply of all materials labour and T & P etc. required for proper completion of the work paint to be used should confirm to the DSR 13.53.1

S/F of 4x2.5 feet size granite stone at site including writing painting with graving and cartage up to site complete/