GE 874/EWS-58/2022-23

Amount

B/R Portion

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out Soft/loose soil all as directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc in hard /dense soil all as specified.

M&L Plain Cement concrete as in foundation filling & mass concrete type D2 1:4:8 using 40 mm graded aggregate all as specified.

M&L Brick work with sub class 'B' brick straight or curved on plan exc. 6m mean radius built in cement mortar 1:4 all as specified.

M&L brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in Cement mortar 1:4.

Returning filling including spreading leveling watering and well ramming in layers n.exc. 25 cm in hard/ dense soil all as specified.

Removal of excavated materials not exc. 50cm and depositing where directed at a level n.exc 1.5m above the starting point all as specified.

M&L Mild Steel TMT bars 10mm dia and over cut to length, bent to shape required including cranking, bending, spirally for hooking for column, hooking ends and binding with MS wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to FS-410 all as specified.

M&L Mild Steel TMT bars 6 to 8mm dia and over cut to length, bent to shape required including cranking, bending, spirally for hooking for column, hooking ends and binding with MS wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to FS-410 all as specified.

M&L for reinforced cement concrete 1:2:4 type B1 using 20mm in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete etc.

M&L for reinforced cement concrete 1:2:4 type B1 using 20mm graded crushed stone agg as in Columns, pillars, piers, posts and struts complete all as specified and directed by engr in charge.

M&L for reinforced cement concrete 1:2:4 type B1 using 20mm graded crushed stone agg as in beams, cantilevers, bressummers, lintel over 1.5mtr span complete all as specified and directed by engr in charge.

M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter.

M&L Formwork to sides of pillars, posts, struts, piers, columns and stanchion Square, rectangular or polygonal.

Formwork to sides and soffits of floor or roof beams, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.

M & L for rendering 15 mm thick on Brick masonry surfaces or surfaces other than fair face of brick work in cement mortar 1:4, to be finished even and smooth (without using extra lime or cement).

M&L for 10mm thick Cement Mortar 1:6 as in internal Plastering on fair face of brick masonry walls and finished even & smooth.

M & L for rendering 15 mm thick on Brick masonry surfaces or surfaces other than fair face of brick work in cement mortar 1:4, to be finished even and smooth (without using extra lime or cement) including mixing of water proofing compond. (Note : Water proofing compound shall be measured and paid separately).

Supply only integral water proofing compound.

Mild Steel Stractural steel work such as Roof trussed (framed) purlins crane guntries rail & fastening and heavy bracket (beam tea angle channel or flat section of Fe 410 -W (GdeE- 250) quality A Fe) including distance pieces cleats etc all as specified.

M&L two coats of synthetic enamel paint over a priming coat with red oxide primer on new steel surface over 10 cm width or girth all as specified.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

M&L two coats of cement based paint on external wall surfaces over a coat of primer including preparation on newly plastered surface complete all as specified.

Applying two coats of white wash including preparation of newly plastered / un plastered surfaces of wall complete all as specified.

M&L two coats of oil bound distemper, on internal wall surfaces over a coat of primer including preparation on newly plastered surface complete all as specified.

M&L Moorum/red bajri filling in floors or paving, laid in layers n exc. 15 cm thick, spread, leveled and rammed including watering.

M&L Hardcore of gauge n.exc. 63mm deposited, spread and levelled in layers n.exc. 15cm thick, watered and rammed to a true surface of broken stone or boulders.

M&L for 75mm thick PCC type D2 1:3:6 (40 mm graded crushed stone agg) as in sub base of floor.

M&L for colored glazed ceramic tiles 350x 250x 7 mm/ 450X 350X 7mm thick as in vertical surfaces such as skirting, dados etc jointed in neat cement slurry and pointed in white or colored cement to match, set and jointed in neat cement slurry and laid over 15mm thick backing coat in cement mortar 1:4, complete all as specified and directed.

M&L Non skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm and n.exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or colored cement to match over 15mm thick screed bed in Cement Mortar 1:4 laid over and including 25mm thick PCC (1:2:4) type B1 using 20 mm graded crushed stone aggregate, complete all as specified and directed.

M & L for second class soft wood plain, solid straight chowkhat and frames, wrought framed rebated on the solid rounded or chamfered, put together with glue pinned and joints.

M&L 30 mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats.

S&F soild PVC door frame of size 50mm x 47mm made out of 5mm plaint color PVC sheet reinforced with MS square tube, and fitted in opening all as specified.

S&F factory made solid PVC moulded door shutter with particle board core 28 to 30mm thick (style) with 2, 4, or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain color PVC sheet on back face, supplying and fixing in frame at site as per specification and drawing.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete omplete with glazing bars, dove tailed or welded including one shop coat of zinc chromites primer complete all as specified and directed.

M&L 2nd class soft wood 25 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats.

S&F Sheet glass ordinary quality 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, in repairs, complete all as specified and as directed.

S&F 4mm thick figured glass/pin headed type ordinary quality fixed in aluminium ventilator n.exc 0.50 Sqm each pane Complete all as specified & as directed.

Mild steel butt hinge medium weight cold rolled 100mm size

Mild steel butt hinge medium weight cold rolled 75mm size

Mild steel pressed handle, oval type stove enamelled, black of size 150mm, complete all as specified.

Mild steel pressed handle, oval type stove enamelled, black of size 100mm, complete all as specified.

S&F Aluminium handles, cast type, anodised 150mm.

S&F Aluminium handles, cast type, anodised 100mm.

S&F 200mm Aluminium anodised, barrel tower bolts of extruded section and fixed.

S&F 150mm Aluminium anodised, barrel tower bolts of extruded section and fixed.

Mild steel barrel tower bolt, stove enamelled black, with bright bolt of 150mm long, complete all as specified.

Mild steel barrel tower bolt, stove enamelled black, with bright bolt of 100mm long, complete all as specified.

S&F mild steel flat as in hold fast, wall ties plain angle clean for securing purline to wood trusses conforming to Fe 290 Gde E-165.

S & F Aluminium alloy, anodised, sliding door bolts, 250 mm plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete, all as specifed and directed.

S&F rotational moulded polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed in position of 1000 ltrs capacity fixed with PVC tank nipples, complete all as specified in SSR Part I.

S&F GI tubing 25 mm dia medium grade galvanished with all fittings laid in floors /wall etc. complete all as specified and as directed.

S&F GI tubing 20 mm dia medium grade galvanished with all fittings laid in floors /wall etc. complete all as specified and as directed.

S&F GI tubing 15 mm dia medium grade galvanished with all fittings laid in floors /wall etc. complete all as specified and as directed.

S&F 3-layer PP-R (polypropylene random copolymer) pipes 16 mm( Outer Dia) SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc.

S&F 3-layer PP-R (polypropylene random copolymer) pipes 20 mm( Outer Dia) SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc.

S&F 20 mm Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed.

S&F 15 mm Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed.

M & L for Vitreous china wash basin, vertically mounted fancy bowl flat back size 550 x 400 mm including waste pipe and coupling 32mm for basins, etc. with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed including MS brackets& waste Pipe complete.

M&L for Vitreous china squatting Pan "Orrisa Pattern" size 580 x 440mm white with integral foot rests incl flush pipe of PVC 32mm dia for low level cistern fixed in repair complete all as specified

S&F PVC valve-less symphonic action type flushing cistern, low level white with inlet ball valve float and handle incl brackets (10 Ltr) capacity fixed in repair complete all as specified and directed.

Soap dish, stainless steel, fixed to wall.

Soap dish, vitreous China white, approximate size 160x 160x90mm.

S&F PVC connection 15mm dia and 600mm long with PTMT nuts and washer complete all as specified.

Stop valve 15mm bore, cast copper alloy screwed down, high pressure, with crutch jor butter fly handle, screwed both ends for iron pipe or for unions

M & L for CP Pillar taps, with capstan head chromium plated 15 mm bore fancy type.

S & F Waste coupling of PTMT (half or full thread ). (Minimum weight 32 mm-45 gms / 40mm-60gms) for 32mm bore dia of discharge pipe fixed to WHB , sink .

Bib tap cast copper alloy chromium plated fancy type with crutch of butterfly handle, screwed down, screwed for iron pipe of for brass ferrule of 15mm bore (ISI marked).

S&F PVC (SWR) floor trap 75mm dia outlet, plain with grating including jointing with solvent cement

S&F 75mm bore PVC (SWR) pipe single socket in any length with rubber ring jointed, fixed to wall complete all as specified.

S&F PVC gully trap square or round mouthed type (P) , size of trap 125x 110mm and jointing to drains with solvent cement in repairs complete all as specified.

S&F 110mm bore PVC (SWR) pipe single socket in any length with rubber ring jointed, complete all as specified.

S&F 110mm bore PVC (SWR) bend or tee or radius complete all as specified.

M&L for PVC (SWR) WC connector with lip ring 110mm.

M&L for PVC (SWR) Reducer for 75 mm dia all as specified.

M&L for PVC (SWR) vent cowl for 75 mm dia all as specified.

Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms) complete all as specified.

Chromium plated shower roses 125mm size with or without swivel joint including fixing to steel pipe or union etc. fixed in repair complete all as specified and directed.

Lagging on pipe of internal dia 15mm used in internal water supply or plumbing all round with, 25min thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum conforming to IS 9843.

Lagging on pipe of internal dia 20mm used in internal water supply or plumbing all round with, 25min thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum conforming to IS 9843.

S&F ball brass valve, with polythelene float and fly nut complete screwed down for iron pipe of 20 mm dia all as directed.

Grating doom 100mm dia of PTMT (Minimum weight 25gms).

Concrete bed to drain pipes 100 mm dia including packing under, and haunching against the sides of pipes after they are laid and tested.

M&L 60mm thick, machine pressed precast concrete interlocking paver block, with grey cement and pigment, any shape and size confirming to IS 15658-2006, M-35 Grade complete all as specified and directed.

Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills,steps,and other similar bands,plinth courses, string courses, lacing courses, parapets and railing upto 60cm height,copings,kneelers,apex stone,bed plates and the like including weathering slightly rounded or chamfered angles and throating, all as specified and directed.

Construction of stone masonary stagging for over head water tank 2.40 mtr heigh from ground level including necessary excavation and earth work in any type of soil all as shown in drawing complete all as specified and directed.

M&L Conventional type 10 users,On site LLDPE septic tank designed to carry sewage and sullage water including excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc., complete all as specified and directed by Engineer-in-Charge.

Soakage well of size 1.8 M dia X 3.0 M effective depth including excavation in ordinary soil, foundation in PCC 1:2:4, brick work in CM 1:4, RCC slab cover incuding RCC precast man hole cover having 6 mm plate embeded alraround/fibre reinf covered with angle iron frame vent shaft in sludge chamber etc.

Demolition of cement concrete (un-reinforced) in ground floors and paving n.exc 15 cm thickness.

Dismantling of timber scantlings 40 sq cm and over in section in any position in unframed work.

M &L for second class soft wood as in scantling clean sawn fixed in position.

M & L for second class soft wood as in scantling clean sawn fixed in position but except wood.

Dismantling of boarding, any description, fixed in any position with nails (including in floor etc).

M & L for 2nd class softwood weather boarding clean sawn, plain 20mm thick or feather edge 15mm to 20mm thick and fixed with 30mm laps.

M & L for 2nd class softwood weather boarding but except material fixed with 30mm laps.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness, including cover fillets.

M&L 6 mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces; fixed with screws to timber frame work in walls.

M&L 6 mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces; fixed with screws to timber frame work in ceiling.

Plain fillet, square, rectangular or triangular in section, clean sawn exc. 3 Sqcm and not exc. 6 Sqcm secured with nails etc.

Dismantling brick work or stone masonry built in cement mortar.

M&L brick work with sub class 'B' bricks (except bricks) of old size, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4.

Taking down cement plaster on brick or stone walls including racking out joints, hacking for key scrubbing down with water etc.

M & L for rendering 15mm thick on stone masonry surfaces or other than fair faces of brick work or on one side of lathing in CM 1:4 finished over and smooth without using extra cement.

Dismantling plain or corrugated steel sheeting any gauge thickness in roof covering.

Taking down chowkhats or frame exe. 1.5sqm and n.exc. 4 sqm each with shutter (without taking out shutter from the frame).

Taking down chowkhats or frame not exc 1.5 Sqm each (without taking off shutters from the frame).

M&L 30mm thick 2nd class hard wood plain framed panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces.The size of rail and stile as per IS:1003 (Part1),kiln seasoned and chemically pressure treated, all as specified and directed.

Hacking out old broken glass (any thickness size quality or description) from wooden frame glazed with putty or wooden beads.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm including fixeing all as specified.

M & L for applying two coats of synthetic enamel point over a coat of pink primer including preparation of new wooden surface exc 10 cm width or girths.

M & L for applying two coats of synthetic enamel point including preparation of old wooden surface exc 10 cm width or girths.

M & L Plain Cements Concrete 1:3:6 type C1 (using 20mm stone aggregate as in plinth protection), 75mm thick finished even and smooth without using extra cement.

Demolition of Reinforced brickwork in suspended slabs, beams, lintels etc. in cement mortar or cement concrete (reinforcement cut as required to facilitate demolition)

M&L 75 mm thick Plain cement concrete 1:4:8 type D2 using 40 mm graded aggregate as in sub base.

M&L Chequered cement concrete tiles (200X200x25mm) thick with grey cement and no pigment, set jointed & pointed in neat cement slurry in floors over and including 15mm thick screed bed of 1:6 cement mortar.

Taking down copper/aluminium point wiring ( light fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing material to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) asd making good distribued surface of wall , floor etc complete all as specified and directed.

Point wiring for one light point/Ex/fan point controlled by one switch with 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi strand cable and 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi stranded cable (green color) as earth lead in and including cable 1100 volts grade including 25mm casing and capping (ISI marked) for one light/ fan point controlled by one switch including CI/MS sunk box of required size, & as directed by Engr in Charge including 3mm thick plastic laminated top sheet cover, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specified.Make : Finolex/Anchor/Polycab

Point wiring for 3 pin 5A socket outlet independent point controlled by one switch with 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi strand cable and 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi stranded cable (green color) as earth lead, 1100 volts grade including 25mm casing and capping (ISI marked) for one light/ fan point controlled by one switch including CI/MS sunk box of required size, & as directed by Engr in Charge including 3mm thick plastic laminated top sheet cover, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specified.Make : Finolex/Anchor/Polycab

Point wiring for 3 pin 5A socket outlet on the same board controlled by one switch with 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi strand cable and 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi stranded cable (green color) as earth lead, 1100 volts grade including 25mm casing and capping (ISI marked) for one light/ fan point controlled by one switch including CI/MS sunk box of required size, & as directed by Engr in Charge including 3mm thick plastic laminated top sheet cover, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specified.Make : Finolex/Anchor/Polycab

Point wiring for one 3 pin 15 Amps socket outlet/sheet metal enclosure independent with 2.5 sqmm PVC insulated un-sheathed copper conductor single core multi strand cable and 1.5 sqmm PVC insulated un-sheathed copper conductor single core cable (green color) as earth lead in and including 25mm PVC caping casing medium grade with all fittings (ISI Marked) controlled by one switch including CI/MS sunk box of required size, & as directed by Engr in Charge including 3mm thick plastic laminated top sheet cover, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specified.Make : Finolex/Anchor/Polycab

S&F for decorative LED batten for surface and pendant applications. Anodized extruded aluminium housing, high transmisitivity diffuser, high lumen output of VIVA MINI LED Luminaires (4FT) of 20W connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed. Make-Havells product code LUMILINEPLUSBS20WLED865SPCSS or equivalent of approved make as approved by Engr-in-Charge

Supply & fixing Switch piano type flush 6 Amp Single pole one way ( ISI Marked) complete all as specified and directed. Make : Havells/Anchor

Supply & fixing socket outlet 2 in 1, 5 and 6 Amp universal type controlled by one switch (ISI marked) complete all as specified and directed. Make : Havells/Anchor/Philips.

Supply & fixing Switch socket combination 2 in 1, 5 and 6 Amp universal type controlled by one switch (ISI marked) complete all as specified and directed. Make : Havells/Anchor/Philips.

Supply & fixing Switch socket combination 5 in 1, 5 and 15 Amp universal type controlled by one switch (ISI marked) complete all as specified and directed. Make : Havells/Anchor/Philips.

S&F rectangular boards/ blocks 30x25x4cm depth closed recessed, wooden pattern, complete all as specified and as directed by Engr-in -charge.

House service bracket (hook type), complete, with 3m long GI pipe 40mm dia medium grade, two Nos 90 degree bend, MS hook and guy or stay, complete all as specified. Make: Havels/Anchor/Polycab/SSK.

Supply & Fixing ceiling rose surface backelite 65x50mm two to three terminal (ISI marked).Make : Havells/Anchor.

S&F lamp holder angle type PVC/Poly carbonate type insulated body with back plate suitable for batten/wall fitting complete all as specified and directed. Make - Anchor/SSK/Cona Havells.

Supply and fix LED Bulb 9 Watt. Make Havells/Bajaj.

S&F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and as directed.

Supply & fix sheet metal enclosure MCB distribution board. Single pole & neutral 240 volts 12 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, conf to Cat Pt No 6077 11 of Legrand or equivalent of make Hager/Merlin Garin fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification .

Supply & fix sheet metal enclosure MCB distribution board. Single pole & neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, conf to Cat Pt No 6077 11 of Legrand or equivalent of make Hager/Merlin Garin fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification .

Supply & Fixing RCBO, Single pole and neutral (SPN) 100mA, 240V, 6-63 Amp all as specified and directed. Make- Havelles/MDS/Legrand.

Supply and fixing MCB SPN 40-63 AMP amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning

Supply and fixing 415 Volts, MCCB TPN 100 AMP amp rating current carrying capacity complete with connection testing and commissioning.

S&F Single phase Voltage protection relay of trip setting 85 to 500 V AC complete with connecting testing and commissioning. All as specified and directed by Engr-in-Charge.

Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning.

Supply laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty) 1100 Volts graded standard aluminium conductor of size 35 sq mm 4 core complete all as specified and directed. Make Havells/Polycab/Gloster

Supply laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty) 1100 Volts graded standard aluminium conductor of size 16 sq mm 4 core complete all as specified and directed. Make Havells/Polycab/Gloster

M & L for sub main wiring with two single core 6 sqmm PVC insulated and unsheathed 1100 volts grade, stranded copper conductor FRLS ISI marked drawn into & including medium grade PVC conduit/ casing caping, with wooden or white colour casing caping (as specified and directed) 25 mm dia with all fittings and accessories and one continuous run of 4 sqmm copper conductor PVC insulated (green colour) as earth wire fixed into PVC casing / conduit (not less than 25mm outer dia) with all fittings and accessories fixed conealed/ surface including taking down old unserviceable submain wiring and making good disturbe surface complete all as specified and directed.Make of cable- Havells ,Plaza, Policab.Make of Casing Caping - Poly plast/ pressfit/ Presto plast.

S&F 1100 volt grade heavy duty cable PVC insulated multistranded aluminum stranded conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 mtr apart including 4mm dia GI suspension wire one twin core cable flat of circular of size 16 Sqmm complete all as specified and as directed by Engr-in-Charge. Make : Havells/Anchor/Polycab/Plaza.

Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron earth lead strip 32x6mm by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 3 of 2009 SSR Pt-I and testing complete including earth work in any type of soil, PCC 1:2:4 type B-0 as in earthing pit and cover 55mm thick reinforced with XPM (weight not less than 4.0Kg/Sqm) common salt, charcoal and testing on completion, all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron earth lead strip 32x6mm by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 3 of 2009 SSR Pt-I and testing complete including earth work in any type of soil, PCC 1:2:4 type B-0 as in earthing pit and cover 55mm thick reinforced with XPM (weight not less than 4.0Kg/Sqm) common salt, charcoal and testing on completion, all as specified and directed.

S & F in repair PTMT nipple 20 mm suitable for HDPE water tank, (Minimum weight 15mm 38gms/20mm-45gms /25mm- 65gms)

M/S SAJAA CONSTRUCTION COMAPNY

M/S AB AHAD RATHER

M/S SS SHAH WALI & CO

Bidder Name

M/S AB AHAD RATHER

M/S SAJAA CONSTRUCTION COMAPNY

M/S SS SHAH WALI & CO

MS SHEIKH NADEEM AKBAR