SPL REPAIR TO RUSTED CI / GI PIPELINE TO JCO / OR AND OFFRS MD ACCN AT HISAR MIL STN UNDER GE (WEST) HISAR

Amount

Taking up or down old steel tubing and connection from trenches / floor / along wall complete all as specified and directed for following sizes :- (Excavation and earth work shall be measured and paid for separately)

15mm bore pipe

20mm bore pipe

25mm bore pipe

40mm bore pipe

50mm bore pipe

80mm bore pipe

100mm bore pipe

Supply, Laying, jointing and testing galvanized iron tubes medium grade with all fittings conforming to IS-1239, laid in trenches or along wall or roofs and in floors etc complete all as specified and directed for following sizes :-

15mmbore pipe

20mmbore pipe

25mm bore pipe

40mm bore pipe

50mm bore pipe

S&F gun metal globe or gate valves,with iron wheel head,screwed both ends for iron pipes and fixed for pipes complete all as specified and directed.

20mm bore pipe

25mm bore pipe

40mm bore pipe

50mm bore pipe

Taking up or down cast iron pipe complete all as specified and directed for following sizes :-

80mm bore pipe

100mm bore pipe

M&L for laying, jointing and testing Ductile iron (DI) pipe with spigot & socketed ends (ISI marked) centrifugally cast of class "K-7" and in any length, laid in trenches including rubber gasket joints complete all as specified and directed for following size :- Note :- Run lead joints & DI fittings shall be measured and paid for separately.

80mm bore pipe

100mm bore pipe

M&L Ductile iron (DI) fittings or specials for flanged / spigot socketd end pipe upto 150mm bore confirming to IS-1538 and ISI marked such as bends, tapers, tee pieces (Single & double branch) any type and angle / radious and straight connecting pieces but all ends flanged complete all as specified and directed.

M&L for run lead joint including preparation of ends, provision of hemp / yarn gasket and piglead filling and proper coulking and testing complete of pipe / fittings complete all as specified and directed for following sizes :-

80mm bore pipe

100mm bore pipe

Supply, fixing, connecting & testing sluice valve, class PN 1.0 cast iron body with forged brass spindle, non rising type & cast iron wheel head, both ends flanged IS-14846 marked, including taking down old U/S sluice valve complete all as specified and directed for following sizes:-

80mm bore

100mm bore

Excavation in trenches in soft/loose soil not exceeding 1.5m wide and not exceeding 1.5 m in depth for laying of cable and getting out complete all as specified and directed.

Excavation in trenches in hard / dense (in road cutting / plinth) soil n.exc 1.5 mtr deep and not exceeding 1.5 mtr in width for taking up / down underground water tubing and / or laying of CI / GI pipes (new or old) of any dia and getting out complete all as specified and directed.

Removal of surplus soil to a distance not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr from starting point complete all as specified and directed.

Returning filling in including spreading, levelling watering and well ramming in layers not exceeding 25 cm thick in soil after the existing water pipe lines have been taken up / out and new /existing pipe line laid and tested complete all as specified and directed.

Demolition of brick work or stone boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

M&L for Brick work with subclass ‘B’ old size bricks, straight or curved on plan exc 6 mtr mean radius built in cement mortar (1:4) complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in roof kerbs on roof chamfered on edge including troweling slightly complete all as specified and as directed.

M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation or mass concrete complete all as specified and directed.

M&L rendering 15mm thick on brick masonry / concrete surfaces in CM 1:4 mixed with liquid water proofing compound as per manufacturers instructions, surface finished even and smooth without using extra cement complete all as secified and directed.

Taking out unsv mild steel covers of valve chambers and supply and fixing covers of valve chambers duly hinged fabricating the frame by using 3.15mm thick mild steel sheet and angle iron of size 40mm x 40mm x 6mm thick inlcuding making locking arrangement and fixing the above cover in PCC and providing hold fast of appropriate size made to shape of 50mm x 6mm mild steel flat including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. Note : PCC shall be measured and paid for separately at item srl No 15.

m/s Rajesh Kumar

M/S KAVITA CONSTRUCTION

M/S D.N Choudhary

P.K. ENTERPRISES