PROVN OF COOK HOUSE, VEGETABLE ROOM, MEAT ROOM AND SPECIAL REPAIR TO MES INSTLN AT NEW CANTT INCLUDING ADDN/ALTN TO BLDG NO. T-149 AT OLD CANTT AND NEW CANTT AREA UNDER GE GANGTOK (2ND CALL)

Amount

B/R Portion Dismantling old PGI/CGI/Fiber sheeting any gauge, thickness including Nainital. Sikkim or similar pattern roof/facia including ridge etc and keeping serviceable sheets in safe custody for re-use complete all as specified and as directed.

Taking down Cement Plaster of any description on Brick Walls, Concrete Surfaces including racking out joints, hacking for key, scrubbing down with Water remove Dust, debries/ rubbish etc., complete all as specified and as directed.

Racking out joints/pointing to brick work in walls of squared rubble masonry, coursed or uncoursed complete all as specified and as directed.

Demolition to cement concrete in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid in cement mortar complete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6), type C2 (using 40mm graded stone aggregate) as in plinth protection/ path/steps/hardstanding etc finished even and fair without using extra cement complete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6), type C2 (using 40mm graded stone aggregate) as in sub base of floor complete all as specified and as directed.

M&L for 25mm thick PCC (1:2:4) type B1 (20mm graded stone aggregate), finished concrete surfaces even and rough to receive floor finishes complete all as specified and directed.

M & L for 100mm thick cement concrete type B-1, 1:2:4 (20 mm graded aggregated) for floor, pavings etc finishing the surface even and fair complete all as specified and directed

Supply and fix 0.50mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheets of any colour and any pattern as approved having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws as in roof complete all as specified and directed.

Supply and fix 0.50mm thick pre-painted galvalume aluminium zinc coating GI based plain steel sheets of any colour having tensile strength of 550 Mpa as in ridges, valley, eaves, etc fixed with self tapping screws complete all as specified and directed by the Engr-in-Charge

M &L Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing incl 15mm thick screed bed with CM 1:6 complete all as specified and as directed.

All as per item no. 11 above but as in skirting/dado/riser to steps etc including 10cm in width and setting in cement slurry & pointed in white or coloured cement to match complete all as specified and as directed.

M&L for lacquer coated chequered cement concrete tiles 20cm x 20cm x 25mm/ 30cm x 30cm x 25mm thick, set jointed and pointed in neat cement slurry in floors with grey cement and pigments over and incl 15mm thick screed bed or bedding layer of in CM 1:6 all as specified.

M&L for pre cast cement concrete block masonry with solid blocks exceeding 10 cm in width and settting in cement mortar 1:6 type C1, (1:3:6) (using 20 mm graded stone aggregate) as per IS-383 complete all as specified and as directed.

M&L for rendering 20mm thick in cement mortar (1:4) in two layer of 10mm thick each with using WPC shall be mixed with cement mortar in finishing outer layer only as per manufacturer's instruction, on other than fair face of brick/stone masonry (external surfaces) finished surface fair and even without using extra cement complete all as specified and as directed. Note : (WPC shall be measured and paid separately as supply only)

M&L for flush pointing in cement mortar (1:4) to block in course or ashlar masonry or concrete block walling complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar (1:6) on fair face of brick or concrete surfaces finished surface even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 5mm thick in cement mortar (1:3) in ceiling finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L applying two coats of weather proof exterior emulsion paint of standard quality and make ,over a coat of white primer including preparation of new plastered surfaces etc complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying three coats of white wash all complete as specified and directed.

M&L for preparation of old plastered surfaces of walls and applying two coats of white wash all as specified and directed.

M&L for preparation of newly/old plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparation of newly/old plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for hardcore of guage n.exc 0.63mm broken stone or boulders deposited, spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface complete all as specified & as directed.

S&F in repair steel rolling shutters with push pull or manual type and with lath 1.25mm with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated complete all as specified and as directed.

S&F safety lever locks mild steel 4 levers for rolling shuters complete all as specified and as directed.

S&F of factory made steel windows with side hung shutters openable type including friction/box type hinges steel handle and peg stay complete with glazing bars fixed to existiog opening and making good to match as per existing surfaces including taking out old/unserviceable steel windows complete all as specified and as directed.

S&F of factory made steel ventilator with top hung shutters openable type including friction/projected type hinges steel handle and peg stay complete without glazing bars fixed to existing opening and making to match as per existing surfaces complete all as specified and as directed including taking down old unserviceable steel ventilators.

Hacking out old broken glass (any thickness , size, quality or description) from metal frame including punching or drilling out old glazing pins/springs clips and removal from the site complete all as directed.

S&F 3mm (tinted) thick sheet glass panes, ordinary quality in squares n.exc 0.5 Sqm each pane complete all as specified and as directed.

S&F framed work such as grills, gratings, etc, with ends of bars shouldered and/or reveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified and as directed.

Material and labour for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in surface channels and drain including forming fair finish the surface even & smooth without using extra cement etc complete all as specified and as directed.

S&F 300mm dia reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and as directed.

Excavation in trenches not exc. 1.5 metre wide and not exc. 1.5 metre in depth and getting in soft/loose soi complete all as specified and as directed.

Excavating in post holes (or similar holes) each n.exc 0.5 Cum getting out and removing surplus soil to a distance n.exc 50m and making good surfaces in soft/loose soil complete all as specified and as directed.

Material and labour for hand packing (any thickness) at back of walls over arches etc & raising etc complete all as specified and directed.

Material and labour for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

M&L for plum concrete consisting of PCC 1:3:6 type C2 (using 20mm graded stone aggregate) mixed with 25% of boulders all as specified (for measurement qty of boulders will be deducted from total volume of concrete and same will be paid separately in supply only) as in wall complete all as specified and as directed.

Supply only boulders exceeding 15cm and upto 30cm dia complete all as specified and as directed.

M&L for PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in coping, bed plates, parapet, plinth course including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

M&L for PCC 1:3:6 type C1 (20mm gradede aggregate) as in coping, bed plates parepet, kerb stone etc including weathering, slightly rounded or chamfered angles and throating, all as specified and as directed.

Material and labour for PCC 1:2:4 type B-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

S&F joist, channel, angle or tee sections, fixed independently without connecting plates etc. (cut to ordinary lengths i.e within 20mm of the length indicate conforming to Fe-410-W (Gde E-250) quality A as in fencing post etc complete all as specified and as directed.

S&F mild steel bands, straps, supports or stays for rainwater, ventiliating pipes incl bolts, hooks for large gates, pintle hinges, large hasp and staples, chains, handmade sliding bolts, clamps, hold fast, and wall tie, hook for hanging fans, plain angle cleats for securing purlins trusses or rafters, knee piece inserts, two way and three way straps, plate washers and all similar small articles conforming to FE-290 Gde and E-165 all as directed and specified by Engr-in-Charge.

S&F Tie bars with screwed ends, nuts, washers and mild steel plates for walls, chimneys, roofs, arches etc kind rods and straining bolt etc complete all as specified and as directed.

S&F PVC coated chain link fencing of 50mmx50mm mesh size and made out of 3.15mm dia (2.15mm dia wire and 1mm thick PVC coating) conforming to IS fixed to any type of standard rails, straining, bolt etc complete all as specified and as directed.

Returning, filling in soil/back filling of retaining walls using approved earth obtained from excavation including watering, well ramming etc complete all as specified and as directed.

Removing excavated materials(soil) to distance n.exc 50 m and depositing where directed at a level n.exc 1.5m above the starting point.

S&F 75mm bore, PVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to wall with necessary clamps etc complete all as specified and as directed.

M&L for formwork to faces of walls, retaining wall etc vertical or batter for rough finished surfaces complete all as specified and as directed.

M &L for formwork to sides and soffits of floor or roof beams, haunchings, girders, bresuummers,lintels, cantilevers, retaining wall etc including sup-ports, overhangs, etc. Also spalys between floors and beams, etc complete.

M & L for applying two coats of synthetic enamel paint on new or previously untreated steel surfaces exc 10cm width or girth over a coat of red oxide zinc chrome primer including preparation of surfaces complete all as specified and as directed.

M & L for applying one coat of synthetic enamel paint on old or previously treated steel surfaces exc 10cm width or girth over a coat of red oxide zinc chrome primer including preparation of surfaces complete all as specified and as directed.

M & L for applying two coats of aluminium paint on new or previously untreated steel surfaces exc 10cm width over a coat of red oxide zinc chrome primer including preparation of surfaces complete all as specified and as directed.

M & L for applying one coat of synthetic enamel paint on old or previously treated steel surfaces not exceeding 10cm width or girth over a coat of red oxide zinc chrome primer including preparation of surfaces complete all as specified and as directed.

M&L for complete removal of existing roof treatment, roughening, cleaning in roof including takin down old APP memberane complete all as specified and as directed.

M&L for providing cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in roof padding, roof curbs to bring top surface of slab in slope complete all as specified and as directed.

M&L for 15mm thick cement screed in cement mortar 1:3 admixed with integral water proofing compound FOSROC complast x 412 IC @ 130 ml per bag cement including a bonding coat of FOSROC''s NiTCO bond AR cement slurry/shalimar Tar product, Mumbai No. 1 liquid @ 200ml per bag complete all as specified and as directed and as per manufactuer's instructions including teting for leakproof treatment.

M&L for applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 Kg/Sqm over applying primer bitumen coat @ 0.30 Kg/SqM including cleaning surfaces complete all as specified and as directed.

M&L for APP based polymeric memberane minimum weighing 3Kg/sqm and minimum 3mm thick reinforced with polyster non wove facric (Wt not less than 15Gm/Sqm) on primed surface including placing and lapping with torching application all as per manufactur's instruction complete all as spd and directed.

S&F plate (plain or chequered), channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment) as in duct cover etc complete conforming to FE-290 Gde-165) complete all as specified and as directed.

M&L for 12mm dia mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, each screwed end to be fitted with washers and one hexagonal or square nut, exc 15cm and n.exc 22.5 cm long complete all as specified and as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and avg 15 cm deep and getting out in soft / loose soil complete all as specified and as directed.

Rough excavation in hard/dense soil not exc. 1.5 metre in depth and getting out complete all as specified and as directed .

Material and labour for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

M&L for plain cement concrete M-10, type C-2 as in retaining wall etc complete all as specified and as directed.

M&L RCC M-25 (design mix) using 20mm graded stone aggr as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L RCC M-25 (design mix) using 20 mm graded stone aggregate as in RCC band , lintel beam complete all as specified and as directed

Material and labour for RCC M-25 (Design Mix ) (using 20 mm graded stone aggregate) as in slabs supported on walls, cover slabs, etc complete all as specified and as directed by the Engr-in-Charge. NOTE : Re-inforcement shall be measured and paid separately.

M&L for RCC M-25 (Design mix) using 20 mm gragrd stone aggregate as in columns, pillars, post & struts complete all as specified and as dircted.

Formwork to sides of concrete foundation, footings, bases of columns, raft & raft beams, sides & soffits (if any) of foundation & similar works, vertical of to batter, rough finished surfaces of concrete flat complete all as specified and as directed.

Formwork to side of concrete column post struts piers and side & soffits (if any) & similar work, vertical to batter, rough finished surface of concrete flat complete all as specified and as dircted.

S&F rolled section as in main and cross beams, hip and jack rafters, purlins where connected to common rafter and running rails and guides for sliding doors fixed with angle clear or other connecting plates conforing to Fe-410-W(Gde-E-250 quality-A)including one coat of red oxide zinc chrome primer after preparation of surfaces at contractor's workshop before fabrication complete all as specified and as directed.

S&F for mild steel tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-1161-1998 grade St-240 including one shop coat of zinc chromate primer paint (including preparation of surface) at contractor's workshop before fabrication and fixing complete all as specified and as directed.

M&L for mild steel TMT bars, 10mm dia and over cut to length, bent to shape required including cranking, bending spirally, hooping for columns, hookings ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for labour for Mild steel TMT bars 5mm dia and over upto including 10mm dia as in stirrups, spacers and binders cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Supply and fix 4mm thick Non asbestos fibre cement building boards (E-board) of approved texture, for insulation and acoustic purpose of size 595 x 595 mm size fixed with staples on snap grid as in ceiling with and including dusting of surfaces and applying two coats of oil emulsion diatemper over a coat of primer including preparation of surfaces complete all as specified and directed .

S&F powder coated GI grid frame work for false ceiling comprising of the following sections for making partitions of 600mm x 600mm size fixed to walls with rawl plugs & screws and hanged to roof with and including 1mm dia GI wire suspender of suitable length and butterfly clips, size of main tee shall be 23mm x 28mm x 0.30mm thick, cross tee shall be 23mm x 28mm x 0.30mm thick and wall angle shall be 20mm x 20mm x 0.30mm thick complete all as specified and as directed.

S&F in repairs stainless steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples complete all as specified & as directed.

S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and as directed.

S&F 25 mm thick Flush door shutter, solid core construction, with block board core and plywood face panels. Commercial type on one side and other face covered with decorative face veneer with lipping / frame to match complete all as specified and as directed.

M&L for 30mm thick 2nd class hard wood well seasoned glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chmafered or rounded, fitted with cut and mitred beads for securing glass, etc,size of members of shutter as specified in SSR Part I, Section 8, Clause 8.24(a) complete all as directed.

Supply and fix 150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed.

Supply and fix aluminium alloy anodised sliding door bolts 250 mm long with hasp staple (Bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section complete all as specified and as directed.

Supply & fix Aluminium handles, 150 mm size, cast type, anodised complete all as specified and as directed.

S&F of 100mm size mild steel butt hinges medium weight complete all as specified and as directed.

M&L for providing 25 mm thick PCC 1:2:4 type B-0 ( Using 12.5mm graded aggregates) concrete surfaces in floors complete all as specified and directed .

Material and labour for 75mm thick sand filling under floors including watering and consolidation complete all as specified and directed by the Engr-in-Charge.

Roughening surcaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and as directed

M&L for 18-20mm thick Granite slab green in one piece machine cut , as in steps , jambs, pillars, window cills, cooking platforms and like bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing including rounding to edges of stone slabs such as in steps , cooking platforms, and other similar situations over and including 20mm thick bedding / backing layer in cement mortar (1:6) complete all as directed.

Materials & labour for coloured glazed ceramic tiles of size (300x200mm/350x250mm/450x350mm) of 7mm thick, as in vertical surfaces such as skirting/dado/riser to steps etc conforming to IS-13712 grade IB-III set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including cement screed bed/backing layer of 10mm thick in cement mortar (1:4) complete all as specified and as directed.

M&L for preparation of old/new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer applied over 3mm thick super fine Birla or altek wall care putty finish including complete removal of existing treatment complete all as specified and as directed.

M&L for preparation of new or previously untreated wooden surfaces of any description n.exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

Form work to sides and soffit of beams, lintels,shelves of slabs/beams and similar works including supports, over hangs etc rough finished surfaces of concrete,flat complete all as specified and as directed.

M& L for form work to chajjas and similar items including edges ,rough finished surfaces of concrete flat complete all as specified and as directed.

M&L for RCC M-25(Design Mix) (20 mm graded stone aggregate) for Chajjas complete all as specified and as directed.

M & L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds mitered/stopped ends etc.

Supply only integral water proofing compound.

S&F in repairs of 12mm thick block boards grade -2 quality interior grade,commercial type including teak wood lipping 6mm thick all round fixed with nails to timber frame work complete all as specified.

S&F 18 / 19mm thick block board grade 2 quality with decorative face veeners on one face fixed with screws to timber frame work as in repair including teak wood lipping 6mm thick all round fixed with nails complete all as specified.

S & F Block boards 25 mm thick, grade 2 quality, interior grade, decorative type with decorative face veneer on both face, fixed with screws to timber frame work including 6mm thick lipping of first class hardwood all as specified.

S & F 100mm Hasp and staple, safety type, anodised aluminium with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified & as directed.

M & L for 40 mm brass knobe for cupboard fixed with nut and screws with bright finishes complete all as specified and as directed.

S & F Continuous (piano) hinges Width of flaps 30 mm , mild steel, bright finish or electrogalvanised

S&F Aluminium anodised,barrel tower bolts of extruded section of 75 mm size fixed complete all as specified and as directed.

Material and labour for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar (1:4) including brought upto course complete all as specified and as directed.

Supply and fixing galvanised steel water tubing 15mm bore, medium grade with all fittings and fixed complete to walls/ceiling or laid in floors all as directed .

Supply & fix angular stop cock made of brass chromium plated screwed both ends for iron pipe for 15mm bore complete all as directed .

S&F for PVC (SWR) (Bore of pipe 200mm) pipes with working pressure 6 kg/cm2 single socketed, in any length with rubber ring joints fixed to walls with necessary clamps, bolts etc complete all as directed by Engr-in-Charge.

S&F for PVC (SWR) bends (Bore of 200mm) any radius fixed to PVC Pipes/Steel Gutters etc complete all as specified and as directed.

M&L PCC 1:3:6 type C-2 concrete bed to drain pipes including packing under & haunching against the sides of pipes after they are laid & tested dia of pipe 150mm complete all as specified and as directed.

M&L cutting into existing manhole for connecting new drains making good to pipe and rendering cutting out existing benching for & forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished & reforming benching as required dia of pipe 150mm complete all as specified and as directed.

S&F for PVC (SWR) tee (T) any radius fixed to PVC Pipes/Steel Gutters etc complete all as directed by Engr-in-Charge (Bore of pipe 110mm)

S & F Mild Steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con forming to Fe.290.Gde-E-165 complete all as specified & as directed.

S&F for PVC (SWR) (Bore of pipe 110mm) pipes single socketed, in any length with rubber ring joints fixed to walls with necessary clamps, bolts etc complete all as directed.

M&L for plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in fixing of hold fast, bed blocks, and similar works etc including necessary form work as required complete all as specified and directed.

S&F for PVC (SWR) bends any radius fixed to PVC Pipes/Steel Gutters etc complete all as directed (Bore of pipe 110mm)

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and as directed.

M&L 2nd class hard wood in scantling fixed in clean sawn complete all as specified and as directed

All as per item No 116 above but except timber scantling.

Dismantling of wall and ceiling board (fibre pulp, insulation etc.,) /AC sheets and plywood any thickness and cover fillets and removal of dismantled materials/rubbish from site complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) each area n.exc 1.5 sqm all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) each area exc 1.5 sqm but n.exc 4.0 sqm all as specified and as directed.

S&F of 75mm size mild steel butt hinges medium weight complete all as specified and as directed.

S&F 100 mm long aluminium anodised handles, cast type, complete all as specified and directed

S&F 200mm long aluminum anodised tower bolts of extruded section and fixed complete all as specified and directed.

S&F 100mm long aluminum anodised tower bolts of extruded section and fixed complete all as specified and directed.

S&F in repair galvanised mild steel wire mesh 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples complete all as specified

Supply and fixing 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts as in walls cladding etc, (Class VIII) all as specified and directed.

All as per item No 126 here-in -before but except sheeting

Supply and fixing 0.63mm thick plain, galvanised, mild steel sheeting, with 275 grams per sqm zinc coating as in ridges, hips, valley gutters, drip & straight flashing etc complete all as specified and directed.

M&L for preparation of newly zinc (or galvanised) surfaces of any description over 10cm in width or girth not otherwise described by coating with mordant solution to receive painting and applying 2 coats of synthetic enamel paint.

M&L for preparation of old zinc or galvanised surfaces of any description over 10cm in width or girth not otherwise described by coating with mordant solution to receive painting and applying one coat of synthatic enamel paint.

Material and labour 6 mm thick plywood, 5 ply, grade BWR type BB fixed with nails to timber frame work in Wall/ Ceiling complete all as specified and as directed.

All as per item No 131 above but except Plywood any thickness.

Material & labour for preparation of old painted surfaces of wood & wood based materials over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as directed by the Engr-in-Charge.

Material and labour for 2nd class hard wood fillets, square, rectangular and triangular in section, wrought, secured with nails,sectional area exe 3 Sqcm but n.exc 6 Sqcm in section complete all as specified and as directed.

M&L 40 mm thick cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in flooring and finised the concrete surfaces even and smooth using extra cement

Material & labour for non skid coloured ceramic tiles of 7 to 8 mm thick (Square/ rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors etc conforming to IS- 13712, grade B-II - (a) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including cement screed bed / bedding layer of 15mm thick in cement mortar (1:6) complete all as specified and as directed..

Demolition of brick work or stone / boulder masonary or precast concrete block walling , built in cement mortar including all quoins, arches, pillars, etc but exclusing ashlar facings, dressed stoneswork and precast concrete articles complete all as specified and as direcetd.

Demolition of precast block masonary or precast concrete article built in cement mortar

Material & labour for RCC (1:2:4), type B-1 (using 20mm graded stone aggregate) ( nominal mix) as in slab supported on walls complete all as specified and as directed.

M&L for use and waste of form work to soffits of suspended slab such as roof slabs, floor slabs, landing and similar works exceeding 200mm thick for flat fair finished surfaces of concrete complete all as specified and as directed.

Demolition of cement concrete in ground floors and paving n exc 15 cm thicness (un-reinforced) below or above ground level complete all as specified and as directed.

Taking down rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed.

S&F PVC (SWR) half round 150mm dia with rounded edges incl all accessories like bend T etc for eaves gutter complete all as specified and directed.

M&L for 2nd class hard wood in scantling fixed in clean sawn complete all as specified and as directed.

M&L 75mm thick PCC 1:3:6 type 2(using 40mm graded stone aggregate) laid in panes as in flooring complete all as specified and as directed.

M&L RCC (Nominal mix) type B1, 1:2:4 using 20mm graded stone aggr as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed

Material & labour for RCC (1:2:4), type B-1 (using 20mm graded stone aggregate) ( nominal mix) as in slab or manhole cover complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar (1:4) in two layer not exc. 10mm thick each with using WPC shall be mixed with cement mortar in finishing outer layer only as per manufacturer's instruction, on other than fair face of brick/stone masonry (external surfaces) finished surface fair and even without using extra cement complete all as specified and as directed. Note : (WPC shall be measured and paid separately as supply only)

M&L for reparation of newly plastered surfaces of walls and applying two coats of cement based paint over a coat of suitable primer on new surfaces of walls all as specified and directed.

Supply and fixed12mm thick and 100mm wide (thickness of concrete) expansion joints filled with pre-formed bituminous filler and top 30mm primed with sealing compound grade B complete all as directed.

E/M Portion Taking down copper/aluminium point wiring (light, fan, socket or power) complete, inlcuding fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc complete all as specified and as directed.

M & L for point wiring with 1.5 Sqmm PVC insulated unsheathed single core stranded copper conductor (FRLS) Cable of working voltage 1100 Volts grade conforming to IS-694 pt-I & II of 2000 drawn in and including 25 mm size PVC rigid non matellic casing caping (Double lock) with all casing capping fittings & accessories with 1.60 mm thick pressed steel or mild steel sheet sunk box covered with 3 mm thick backelite sheet fixed with brass screws & cup washers including 1.5 sqmm PVC insulated unsheathed single core stranded copper conductor (FRLS) cable as earth continuity conductor connected to main switch / DB's or common earth dolly complete for for light point/ fan point/ exhaust fan point/ call bell point/ controlled by one switch 5/6 Amp one way complete all as specified and directed.

All as per item No. 151 above but one exhaust fan/ceiling fan point controlled by one switch 5/6 Amps

All as per item No. 151 above above but one 5 pin, 5 Amps switch socket point controlled by one switch with 1.5 Sqmm copper cable on independent board.

All as per item No. 151 above but for one socket outlet of 15 Amps fixed on independent board with 4 Sqmm multistranded copper conductor wire FRLS PVC insulated and 4 Sqmm copper conductor wire FRLS PVC insulated using as earth wire complete all as specified and as directed.

M&L for point wiring with 1.5Sqmm (nominal cross sectional area) PVC insulated unsheathed single core FRLS copper cable working voltage 1100V grade confirming to IS-694 with multi standed copper conductor in including PVC rigid non metallic 25mm PVC conduit including PVC polycarbonate/PVC/rectangular block box of suitable size fixed by means of brass macine screw and cap washer incl size 1.5 Sqmm (nominal cross sectional area) PVC insulated unsheathed single core multi standed copper conductor cable as earth continuity conductor connected to main switch/DBs or common earth dolly complete all specified and directed for one light point controlled by one switch. Complete all as specified and as directed.

All as item as per item No. 155 but for one 5 pin 5 Amps switch socket point controlled by one switch with 1.5 Sqmm copper cable independent board

All as item as per item No. 155 but for one 5 pin 5 Amps switch socket point controlled by one switch with 1.5 Sqmm copper cable same board

All as item as per item No. 155 but for 2.5 Sqmm copper conductor with 2.5 Sqmm earth standerd wire for 16 Amps power point in independent board

S&F in repairs switch piano flush button,single pole,one way(ISI marked), 6 amps complete all as specified and as directed.

S&F in repair ceiling rose, PVC/polycarbonate insulated body, 3 terminal and 240 volts, ISI marked complete all as specified and directed

S&F in repairs switch socket combination, 2 and 3 pin, 5/6 amps, multipurpose, flush, non shutter, non inter locking type, 230 volt flush type, white/ivory finish with two fixing hole including suitable gang box complete all as directed including taking down old one.

S&F in repairs switch socket combination, 2 in 1, 6 pin, 5/6 Amps and 15/16 Amps, multipurpose , flush, non shutter, non inter locking type, 230 volt flush type, white/ivory finish with two fixing hole including suitable gang box complete complete all as directed including taking down old one.

S&F in repairs lamp holder angular/straight insulated body, with back plate suitable for batten fittings, white/ivory finish complete all as directed.

Supply and fix exhaust fan, steel body AC single Phase, 230V of size 300mm sweep with, blades and frame and louvers complete all as specified and as directed.

S&F decorative LED tube light fitting 1x18 Watt, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F LED light fitting 1x9W/1x10W bulk head luminaries inlcuding LED light driver holder connecting conneting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F in repairs sheet metal enclosure DB's 240 Volts, IP-43, suitable for mounting MCB's, SPN, 4 way with 200 Amps rated copper bus bar double door type complete and including taking down old DB with MCB complete all as specified and as directed.

S&F in repairs MCB single pole & neutral 40 to 63 Amps, 240 Volts, 10 KA rapturing capacity, 'C' Curve complete all as directed .

S&F in repairs MCB single pole 6 to 32 Amps, 240 Volts, 10 KA rapturing capacity, 'C' Curve complete all as directed .

Earthing complete with galvanised steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connected with galvanised iron/steel earth wire of 4mm dia by means of bolts, nuts, check nuts and washers made outof galvanised iron or steel all as shown in electrical plate No. 3 of SSR Part-I and earth wire protected by galvanized pipe light grade 15mm bore and connected to VTPN DB/SPN DB including neccessary earthwork and excavation in any type of soil, GI light grade 20mm bore watering pipe with funnel and wire mesh, PCC 1:2:4 type B1 chamber with 40mm thick RCC 1:2;4 type B1 design mix cover slab with 6mm dia MS bars at 100mm c/c both ways with MS hook 6mm dia MS bars etc complete all as specified and as directed including testing on completion.

S&F of kitchen chimney 90 cm, suction capacity 1000 M3/hr , glass vertical kitchen chimney push buttons stainless steel baffle filter wall mounted type complete all as specified and as directed.

S&F in repairs sheet metal enclosure DB's 240 Volts, IP-43, suitable for mounting MCB's, SPN, 8 way with 200 Amps rated copper bus bar double door type complete and including taking down old DB with MCB complete all as specified and as directed.

M&L for submain wiring alongwith earth wire of size 2x6.0 Sqmm + 1x6 Sqmm earth wire ISI marked FRLS PVC insulated multi stranded copper conductor single core cable drawn in and incl PVC casing and caping of adequate size with all accessories as required as specified and as directed incl taking down old unserviceable submain wiring. (Note : Three run of PVC wire with one runs of PVC casing and caping will be measured and paid as one length.)

Supply, Laying, jointing & testing 1100 volts grade, XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured LT electric power under ground cables conforming to IS 7098(Part-I)-1988, heavy duty with aluminium stranded conductor laid in trenches or passing through pipe of cross sectional area 16 sqmm 2 core with all fixing & connecting accessories complete all as specified & as directed. Note:- (i) Earthwork & Excavation, GI pipe brick protection etc shall be measured and paid separately under relevant items of this schedule. (ii) The rate quoted by the bidder shall deemed to be inclusive of the cost of aluminium thimbles/lugs glands, terminal of suitable sizes."

S&F electrical water heater storage with copper inner tank and heating element, capacity 50 Ltr BEE 5 Star rated complete with accesories such as safety valve thermostate, NRV, connection piece etc.

Supply & fix in replacement Rotational moulded polyethylene water storage tank, 1000 litres capacity, ISI marked multi layer constriction (cylindrical vertical with closed top), hoisted & fixed in position including supply and fixing of 25mm bore Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe of having weight not less than 455 gms including connection complete all as specified and as directed

Supply and fix galvanised steel water tubing 25mm bore medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as directed.

S&F in repairs 15mm bore Brass CP mixer for mixing holt & cold water screwed down for iron pipe and fixed complete all as specified and as directed.

S & F 15mm bore gun metal gate valves , ISI marked with iron wheel head ,screwed both ends for iron pipe and fixed complete all as directed and specified

S & F 25mm bore gun metal gate valves , ISI marked with iron wheel head ,screwed both ends for iron pipe and fixed complete all as directed and specified

Supply and fix galvanised steel water tubing 15mm bore medium grade with all fittings and fixed complete to walls/ ceiling or laid in floors complete all as specified and as directed.

Supply & fix 15mm bore dia angular stop cocks, chromium plated, with wall flange screwed down, screwed from iron pipe or union and complete all as specified and as directed

Supply & fix stop connection 15mm size with PTMT nuts of length 750 mm complete all as specified and as directed.

Screwing 25mm bore in existing steel tubing for alteration or additions (or lengthening screw on pipe to forming connections) complete all as specified and as directed.

KAMLESH ENTERPRISE

M/S S. S CHETTRI AND SONS

SANJAY KAUSHIK

M/S ANIL KUMAR THAKUR

M/S MANOJ VERMA

BIJAY MITTAL

MAHENDRA KHAWAS