Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹33.0 LAccepted-AOC | L1 | Accepted-AOC LOWEST BIDDER | |
| 2 | L2₹35.7 L+₹2.0 L (6.09%)Rejected-AOC | L2 | Rejected-AOC SECOND LOWEST BIDDER | |
| 3 | L3₹36.3 L+₹2.7 L (8.04%)Rejected-AOC | L3 | Rejected-AOC THIRD LOWEST BIDDER | |
| 4 | L4₹36.9 L+₹3.3 L (9.70%)Rejected-AOC | L4 | Rejected-AOC FOURTH LOWEST BIDDER | |
| 5 | L5₹38.2 L+₹4.6 L (13.7%)Rejected-AOC | L5 | Rejected-AOC FIFTH LOWEST BIDDER |
Tender Value
₹44 L
EMD Value
₹88,000
Closing Date
26 Dec 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE NAGROTA
GE NAGROTA
Spl repairs to Married Accn Bldg No PN-27 A to H , NP-95 A to D and certain Minor works under GE Nagrota.
2022_MES_565422_2
GEN-48/2022-23
Open Tender
Civil Works
Item Rate
180 days
GE NAGROTA
Please refer Tender documents.
8 documents required · 8 mandatory
₹500
GE NAGROTA
₹88,000
Yes
30 Mar 2023
12 Dec 2022
28 Dec 2022
12 Dec 2022
26 Dec 2022
19 Dec 2022
Amount
Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc 1.50 sqm each and removing from site.
Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm eachand n exc 4 sqm and removing from site.
Taking down shutter of any description area exc. 1 Sqm and n.exc. 2 Sqm and removing from site.
Demolition of brick work built in cement mortar including all quions, arches, pillars etc but excluding ashlar facings dressed stone work and precast concrete articles.
Demolition of cement concrete (unreinforced) in ground floors and paving not exc 15cm thickness.
Demolition of cement concrete (unreinforced) of any description and any position not other wise specifically provided.
Demolition of cement concrete (Reinforced) of any description and any position not other wise specifically provided reinforcement cut as required to facilitate demoltion.
Taking down cement plaster on brick or stone wall etc including racking out joints, hacking for key scrubbing down with water etc to receive new plaster etc.
Pressed steel frames of size 125 mm X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including two coats of synthetic enamel paint over one coat of red oxide complete.
Pressed steel frames of size 105 mm X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including two coats of synthetic enamel paint over one coat of red oxide complete.
Box type Steel window side hung double shutters with provision for desert cooler/AC(inside for wire mesh & out side for glass), including guard bar,hinges, steel handle, tower bolt and steel peg stay complete with glazing bar dovetailed or welded and fixed, steel window shall be conforming to relevant IS complete all as shown on drawing No CEUZ/TD/1302/09, Sh 1/3 to 3/3 and directed. Note:- Wire mesh and sheet glass shall be measured and paid separately
S & F Box type Steel windows with double shutters (inside for wiremesh & out side for glass), incl guard bar,hinges, steel handle, tower bolt and steel peg stay complete with glazing bar dovetailed or welded including two coats of synthetic enamel paint over one coat of red oxide complete.
Steel ventilators top hung double shutters (inside for wire mesh & out side for glass), including hinges, steel handle, tower bolt and steel peg stay complete with glazing bar dovetailed or welded including a coat of red oxide after preparation of surface before fixing.Steel window shall be conforming to relevant IS all as specified. Note:- Wire mesh and sheet glass shall be measured and paid separately
Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain PVC sheets for top rail lock rail and bottom rail on either side and as gap insert for top rail and bottom rail penelling of plain colour PVC sheetto be fitted in the MS frame welded/sealed to the styles and rails with suitablePVC sheet beading and joined together with solvent cement, suppling and fixing in the frame at site as per specification and drawings.
Supply and fix for PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube complete all as specified and as directed.
Factory made, 2nd class hard wood, plain framed, Double/Single paneled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both sides, the size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, 35 mm thick complete, all as specified .
35mm thick 2nd class hard wood glazed and skelton shutter open rebated and prepared to receive glass ,gauge etc ( without sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc size of members of shutters as specified in SSR Part-I, section 8 clause 8.20(a), supplied and fitted to chowkats.
Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm dia and fixed with tinned tacks or galvanised mild steel staples
Sheet glass 3.00mm thick ordinary quality and glazing with oil putty complete all as specified and directed.
Same all as per item No 28 but pin head type glass.
Curtain rod 25mm dia aluminum brass polished with ends bulbs rings of required size including bracket complete all as directed.
M&L for PCC 1:2:4 type B-1 (20mm graded aggregate ) 25mm thick as in Sub base floor
M & L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles over and including 15mm thick screed bed in cement mortar 1:4 complete including dismantaling /demolation/Taking down Note:- Rates also includes in this item for necessary raking,circular cutting or notching and waste on tiles
M & L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles over and including 15mm thick screed bed in cement mortar 1:4 complete including dismantaling /demolation/Taking down Note:- Rates also includes in this item for necessary raking,circular cutting or notching and waste on tiles
M & L for Glazed ceramic colored tiles 300mmx600mmx 6 to 7mm thick,as in patches in vertical surfaces such as dado, skirting, wall etc set & jointed in neat cement slurry and pointed with coloured cement to match with tiles in over and including 10mm thick cement plaster in cement mortar 1:4. including dismantaling/demolation/Taking down Note:- Rates also includes in this item for necessary raking, circular cutting or notching and waste on tiles
100mm long butt hinges (medium weight) colled rolled mild steel fixed with welding.
Extruded aluminium alloy handles fabricated type anodised of size 125mm long
MS 300 mm ordinary rat rails rod pattern door springs including roller and roller plate.
Hold fast/clamps of mild steel stay for rain water pipes etc confirm to Fe-290 Gde E 165.
S& F Floor door stopper of aluminium alloy body and tongue ,anodised ,with hard drawn steel spring ,fixed in floor overall length of cover plate 140mm
Hasp and staple Alumnium anodised lncluding bolt to hinges plate 100mm size
300mm long aluminium alloy, anodized sliding door bolt with hasp stapple ( bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed.
Aluminium anodized 200mm long barrel tower bolt of extruded section and fixed.
S&F 18/19mm thick solid PVC board prelaminated one side and other side plain as in board/shelves/kitchen cabinate ( Board must be water proofing ,termite proof) .
Brick work with sub class “B” bricks straight or curved on plan exc 6M mean radius build in CM 1:6 using all as specified using old size bricks
Brick work with sub class “B” bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 using all as specified using old size bricks
M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement all as specified ( internally)
M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even and smooth without using extra cement with Water proffing compound all as specified (WPC measure and pais saperately)
M&L for Rendering 5 mm thick in CM (1:3) on ceiling finished even and smooth without using extra cement including two coat of white wash on ceiling including preparation of surface .
Supply only Liquid water proofing compound.
Taking down cement plaster of any description on parapets and providing 10mm thick cement plaster in CM 1:4 on parapets over roof and finished surface even and smooth without using extra cement
M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even and smooth without using extra cement with Water proffing compound all as specified (WPC measure and pais saperately)
Taking down existing cement plaster of any description over damaged surfaces irregular facia, chajjas and in similar work and also for narrow width etc and rendering dubbing coat 15mm thick cement plaster in CM (1:4) over a coat of cement slurry @ 3.00 Kg/Sqm making surface even ( avg 50mm thick PCC 1:2:4 type B-1 using 20mm crushed stone aggregate shall be provided wherever required) followed by 05mm thick rendering in CM (1:3) finished complete all as specified and directed including two coats of cement base paint over a coat of primer over new plaster surface including preparation etc complete.(after curing of specified time and drying the surfaces as required).
Applying two coat of synthetic enamel paint over a coat of pink primer on new wooden surfaces of any description, not otherwise described over 10 cm width or girth including preparation of surfaces.
M&L for Complete removal of existing treatment applying two coats of oil bound distemper over a coat of wall putty 2 to 3mm thick on plasterd surfaces preparatory to distempering on wall surface .
M&L for Preparing newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of wall putty 2 to 3mm thick on plasterd surfaces preparatory to distempering on wall surface .
Preparing newly plastered surfaces of walls and applying two coats of cement base paint over a coat of wall putty 2 to 3mm thick on plasterd surfaces complete all as specified and directed.
Complete removal of existing treatment applying two coats of cement base paint old wall surface over a coat of wall putty 2 to 3mm thick on plasterd surfacescomplete all as specified and directed.
Three coat of white wash on newly plastered surface on wall including preparation of surface complete all as specified and directed.
Three coat of white wash on old surface on wall including preparation of surface complete all as specified and directed.
Preparation of newly plastered surfces of Ceiling and applying two coats of oil bound distemper over a coat of wall care putty 3mm thick
Preparation of Complete removal of existing trreatment preparing old plastered surfaces of Ceiling and applying two coats of oil bound distemper over a coat of wall care putty 3mm thick
Demolition of stone slabs of any description or thickness in kitchen platform, floors,aprons laid, bedded,pointing in any mortar etc complete all as directed.
M&L for Machine cut kota stone flooring 18 -22 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing ( mirror finish) (Each stone not less than 55 cms x 55 cms) over 15mm thick screed bed in CM ( 1:4) as in floor finished.
M&L for Machine cut kota stone slab 18-22mm thick in skirting, dado and pillars, risers of steps laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing ( mirror finish) over 15 mm thick rendering in CM ( 1:4) including taking out of existing dado.
M & L for 62 cm wide Udaypur green stone 15 to 18 mm thick. (table rubbed and polished) as in cooking plateform of size not less than 2 m in length, incl cutting for sink over prepared surface and pointing with white cement 1:2 using marble dusts admixture of pigment to match including 15mm thick screed bed in CM 1:4.
All as per item above but as on edges of cooking plateform laid over 15mm thick rendering in CM (1:3) -ditto-.
PCC 1:2:4 type B-1 as in benching, coping etc and similar items including weathering slightly rounded or chamfered angles and throating on top of roof, chajjas, rails, cills etc.
PCC 1:3:6 C-1 (using 20mm graded crushed stone aggregate) as in plinth protection (75mm thick ) finished even and fair all as specified.
RCC 1:2:4 type B-1 ( using 20mm graded crushed stoneagg) as in chajjas, shelves and similar items.
RCC 1:2:4 type B-1 ( using 20mm graded crushed stoneagg) as in wall, Parapet wall and similar items.
Providing 75mm thick precast reinforced cement concrete slab 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) and set in CM 1:4 . ( NOTE : (reinforcement shall be measured and paid for separately).
Form work to chajjas, shelves ,troughs and similar items including edges.
Form work to edges of concrete flats RCC/PCC band exc 5 cm but exc 10 cm. Fair finished
TMT bars 10mm dia and over cut to lengths bent to shape required including cranking bending and spirally hoping for columns hooking ends and binding with MS wire annealed n.less then 0.90mm dia.
All as per item above but 6mm to 8mm dia -ditto-.
Providing number plate of size 450 x 300x20mm in CM 1:4 and writing building No of height 8 to 10cms with luminous paint through grooves of size 12 x 12mm ( Base: Black, grooves : orange)
Rotational moulded polyethene water storage tank 500 ltr capacity hoisted and fixed in position including PVC float valve 20 mm bore and including dismantling of existing water storage tank complete.
Taking up or down steel tubing and connections including cleaning for refixing or removal to store upto 25mm bore.
15mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs.
20mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs.
Cuttings chases for concealed water tubing of concealed conduit (cutting n.exc 10 cms girth) and making good in CM ( 1:3) in brick walls.
Shower rose brass chrominium plated 125mm size complete all as specified and directed.
15mm bore fancy type bib tap brass CP (Long body) with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed. MAKE :PARRYWARE,JAQUAR,KOHLER
15mm bore fancy type CP brass Mixer, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed. MAKE :PARRYWARE,JAQUAR,KOHLER
S&F Cast copper alloy CP angle Valve fancy type screwed both ends for iron pipe 15mm dia/ bore of pipe MAKE :PARRYWARE,JAQUAR,KOHLER
All as per item above but with long shank and cup (concealed type) MAKE :PARRYWARE,JAQUAR,KOHLER
Stop valves ,cast copper alloy ,screwed down high pressure , with crutch or butterfly handle , screwed both ends for iron pipe or for union 20mm dia MAKE :PARRYWARE,JAQUAR,KOHLER
CP Pillar taps, 15mm fancy type cast copper alloy, with capstan heads, screwed down high pressure, without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed. MAKE :PARRYWARE,JAQUAR,KOHLER
Soap dish with including chromium plated brass screws and wooden/plastic cleats ( Minimum weight 105gm). MAKE :PARRYWARE,JAQUAR,KOHLER
Towel rail 600mm long of PTMT fixed with including chromium plated brass screws and wooden/plastic cleats ( Minimum weight 190gm). MAKE :PARRYWARE,JAQUAR,KOHLER
Vitreous china squatting pan “ORISSA” pattern size 630x450mm ( Make : Hindware)white with integral foot rests all as fixed in repairs including cast iron ‘P’ or ‘S’ trap 100mm bore including PVC low level cistern of 10 litres capacity including brackets jointing to flush pipe, PVC connection (600x15mm), flushing pipe complete fixed in repair all as directed by Engr-in-Charge.
Dismantling cast-iron/PVC pipes including fittings taking out of trenches or walls as required dia of pipe upto 100mm.
S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls for 110mm bore.
S&F PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floor for 110mm bore.
S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls for 75mm bore.
S&F PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floor for 75mm bore.
S&F PVC (SWR) Bends any radius for 110mm bore.
S&F PVC (SWR) Bends any radius for 75mm bore with oval access door.
S&F PVC (SWR) Branch pieces single( Single Y) equal or unequal) for 110mm bore with oval access doors.
S&F PVC (SWR) Branch pieces single ( Single Y) equal or unequal for 75mm bore with oval access doors.
S&F PVC (SWR) vent cowl 75mm
Ditto as per above but 110mm
Taking down existing AC pipes any dia as in spouts etc and providing 110 mm bore PVC (SWR) pipes in short length as in spouts fixed with PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate.
Taking down existing old tarfelt, bituminous compound including cleaning & removing debris to a distance exc 100 m n.exc.250m.
M&L for 10 mm rendering in CM 1:4 including water proofing compound @2% of cement over roof surfaces finished even and smooth without using extra cement complete all as specified Note:- WPC Mesured and Paid Separately.
Supplied only for Integral water proofing compound.
M&L for Applying bituminous primer @ 0.40 litre per Sqm over plastered surfaces of roof including parapet surfaces
M&L for Applying evenly a tack coat of induatrial bitumen 85/25 grade @ 1.2 Kg/Sqm.
M&L for One layer of APP based polymeric membrane of approved manufacturer, 3mm thick, weight not less than 3.50 Kgs per Sqm , reinforced with non woven polyester fabric or weight not less than 150 gms per Sqm . Polymeric membrane shall be taken to a height 60 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing(Note (i) Laying of APP based polymeric membrane shall be done by torch on method or as per manufacturers instructions (ii) A Minimum overlap of 100 mm and 75 mm should be made in the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as manufacturers instructions (iii) The make of polymeric membrane shall be IWL India Ltd chennai. Ltd or "MOPLY FP" of Texsa India Ltd). NOTE : S&F of APP based polimeric membrane of approved manufacturer will be laid/fixed by authorised person of the same manufacturers units asper relevent IS.
Applying one coat of aluminium paint on top of APP membrane.
PCC 1:2:4 type B-0 (12.50mm graded aggregate) as in padding finished even and smooth without using extra cement all as specified and directed.
Removing old tarfelt or polythene film including taking down plaster of sunken floor , roughening and cleaning by brushing with wire brush to remove all dirt and apply a coat of cement slurry with 3.00 Kg of cement per sqm and Rendering 15mm thick in CM 1:3 using WPC finished rough (sunken floor/wall) and then applying two course treatment as follow :-(i) Applying bitumen primer @ 0.40Kg/Sqm (ii) Laying APP (Atactic polypropylene) modified membrance 3mm thick and weighting not less than 3 Kg/Sqm with 100 GSM/Sqm non woven polyester mat as center core reinforcement, laid with 75 mm side over lap and 100mm end over lap. The membrane has to be laid with LPG torch and over lap sealed and finished neat.
S&F as in repair kitchen rack made out of 0.63mm thick stainless steel sheet wall mounted type with 5/6 partition of size 60 cms x 90 cms x 25 cm fixed on wooden gutties complete all as directed by Engr-in-Charge.
Stainless steel Kitchen sink with drainage board made out of 1mm thick sheet for kitchen or laboratory with plug, washer, waste pipe etc including cast iron brackets, connecting union over all size 915mm X 460mm with bowl size 410mm X 330mm X 160mm complete
S&F in repairs wash hand basin, vitreous china, white, flat back (550x400mm) cutting for and pinning ends of brackets(Make:Parryware Code No.-0471,Indus Basin (white) or equivalent.
Vitreous china wash basin white Angle back size 400 x 400mm incl waste pipe chain plugs and 32mm dia bore CP coupling complete as in repairs including a pair of bracket.
Shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 300 grams)
PCC 1:4:8 D-2 (using 40mm graded crushed stone aggregate) as a sub base to chequred tile ( 75mm thick ) finished even and rough.
20mm thick screed or screed bedding in cement mortar 1:4 as a sub base to interlocking tile
M&L chequered cement tiles concrete 30cm x 30cm x 25mm thic, set jointed in neat cement slurry in floor including 15mm thick screed bed or bedding layer of mortar 1:4 for laying floor finishes etc all as specified. .
100mm bore CI floor trap with grating including jointing CI pipe in run lead, cutting holes in walls and making good surface in cement concrete surface type B-1 (1:2:4)
75mm bore CI floor trap with grating including jointing CI pipe in run lead, cutting holes in walls and making good surface in cement concrete surface type B-1 (1:2:4)
100mm bore CI Nahani trap with grating including jointing CI pipe in run lead, cutting holes in walls and making good surface in cement concrete surface type B-1 (1:2:4)
M & L for 100mm dia Cast iron pipes with flanged ends, centrifu?gally cast, class A, in any length laid in trenches complete all as specified and directed.
M & L for 80mm dia Cast iron pipes with flanged ends, centrifu?gally cast, class A, in any length laid in trenches complete all as specified and directed.
M & L for upto 150mm bore Bends (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces single branch. "Y" junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs complete all as specified and directed.
Cutting into existing manhole for connecting new drains and making good to pipes and rendering cutting out existing benching for and forming branching for and forming branch channel (1/2 round or ¼ section ) in PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate smooth finished and reforming benching as specified and directed for 150mm dia of pipe complete all as specified.
Demolition and breaking up 150mm dia drain pipes (Salt glazed ware, AC or reinforced concrete ) and set in cement mortar all as spd and directed by Engr in Charge.
Concrete bed to drain pipes laid in trenches including packing under and haunching against the sides of pipes aftaer they are laid and tested in cement concrete 1:4:8 type D-2, using 40mm graded crushed stone aggregate for 150mm bore pipe, complete all as specified and as directed by Engr in charge.
M & L for Salt -Glazed stoneware drain pipes 150 mm dia laind in trenches and jointed complete all as spd and directed
Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in Soft/ loose soil.
Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils.
Removing Excavated soils not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point.
M/L Plain Cement Concrete Type D-2 1:4:8 (using 40 mm graded granite stone aggregate) in foundations, filling and mass concrete.
75 mm thick Cement concrete type D 2, 1:4:8 (using 40 mm graded granite stone aggregate) in sub base of flooring/ hard standing.
Brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6
Reinforced cement concretetc M-25 (design Mix) using 20mm graded stone aggregate as in foundation, plinth beams,footings etc,.
Reinforced cement concretetc M-25 (design Mix) using 20mm graded stone aggregate as in columns.
Reinforced cement concretetc M-25 (design Mix) using 20mm graded stone aggregate as in floor or roof beams
Reinforced Cement Concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) for slabs suspended on walls, beams and columns, in floors, roofs, landings and in shelves and the like.
M/L Fair finished flat Form work to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exceeding 200 mm thick.
Use and waste of formwork for sides of columns.
Use and waste of formwork for foundation beams floor beam roof beam etc as in lintel over 1.5m clear span. for rough finished surfaces
Use and waste of formwork to sides and soffits of floor or roof beam, beam hauchings, girder, bressum-mers, lintels, cantilivers, shelves incl supports, overhangs, etc. Also splay between floors and beams, etc. for rough finished surfaces
M & L TMT bar 10mm dia and over cut to length bend to shape required indd cranking bending spirally for column, hooking ends & binding with and incld mild steel wire (annealed) not less than 0.90mm dia or securing with chips as directed
Mild steel TMT bars 8 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, beams,hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips.
Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups,spacers and binders
Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished fair and even without using extra cement.
Preparing newly plastered surfaces of walls and applying three coats of white wash.
M&L rendering 15 mm thick on external surfaces of wall in cement mortar 1:4 all as specified and directed.
M & L preparing new plastered surfaces of walls and applying two coats of cement base paint.
M&L rendering 5 mm thick on internal surfaces of ceiling in cement mortar 1:6 finished even & smooth without using extra cement as specified and directed.
Preparing newly plastered surfaces of ceilings and applying three coats of white wash.
S&F , 20 mm bore, ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule. complete all as specified and directed.
S & F vitreous china squatting pan "orissa pattern, size 580x440mm white , with integral foot rests(excluding flushing cistern and flush pipe) including provison of lean concrete bedding connection to drain out pipe, to flush pipe and antisyphonage pipe etc, complete all as specified.(Make: Jaguar, Parry ware or somani)
S& F PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve float and handle including brackets (10 ltr) including mild steel tube 32mm dia flush pipe..(Make: Jaguar, Parry ware or Cera).
M&L For extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including form moulds mitred/stopped ends etc. complete.
Surface excavation n.exc 30cm deep and avg 15 cm deep and getting out any type of soil.
S&F aluminium (powder coated with approved colour) ventilator, partially glazed and partially louvers, outer frame & mullion fabricated with aluminium section of size 82.50 mm x 38.00 mm x 1.50 mm thick (Cat No 20036), half portion glazed with 4 mm thick frosted glass including rubber beading, & glazing clip, half portion louvers of 80 mm wide & 4 mm thick frosted glass including aluminium louver patti including S.S wire gauge of fixing of 0.36mm dia and 1.40 width of aperture with 25x3mm think aluminium strip with screw to upper half portion of ventilator all fitting & fixture and fixed in position. Note:-(i) Section No given above are of Make-Jindal,
S&F white vitreous china counter wash hand basin, of size-410X910X150mm fixed in granite counter by making suitable size hole, new brackets, 32mm dia brass chromium plated waste coupling, CP botle trap complete all as specified
S&F health faucet with 1 meter long easy flex tube in chrome finish & wall hook, complete all as
Supply and fixing Vitreous China Urinal, full stall type, white with PTMT waste fitting, PVC waste pipe, brass CP urinal spreader including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws complete all as specified and directed.
Taking down carefully unserviceable Aluminium point wiring complete (light, fan socket, bell or power) with fitting such as switches, ceiling rose lamp holder, regulators, sockets, light fittings etc. and keeping in safe custedy for taking credit all as specified and as directed by Engr-in-Charge
Taking down ceiling fan any sweep, removing blades ,cleaning the fan completely for dust and dirt, oiling & greasing and hanging the same back to its original positions including connecting with three core flexible copper wire to ceiling rose etc after the completion of the point wiring including replacement of old unserviceable fan hook, rubber pad, nut bolts and washers etc, complete, all as specified and directed by Engr-In-Charge.
Taking down existing energy meters, keeping aside safely & refixing the same in its original position after making functional & after completion of point wiring/sub main wiring, complete, all as specified and directed by Engr-In-Charge. Note:- Small items required for fixing the electric energy meter at site shall be provided by the contractor and cost for the same shall be deemed to be included in the quoted rates.
Taking down existing electric water heater, keeping aside safely & refixing the same to its original position after servicing of the whole geyser/making functional and after completion of wiring work, complete, all as specified and directed by Engr-In-Charge. Note: If any part found unserviceable during the refixing of water heater at site shall be provided by the contractor and cost for the same shall be deemed to be included in the quoted rates.
M&L for point wiring with PVC insulated unsheathed 1100 volt grade FRLS cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium grade ISI marked not less than 20mm dia ,concealed in wall and surface on ceiling with all conduit fittings & fixing acessories inculding sunken anodised pressed steel terminal box not less than 1.2mm thick covered with 3 mm thick plastic laminated sheet cover of suitable size with brass screws for mounting switches, sockets, regulators with and including 1.5sqmm FRLS multi stranded copper conductor drawing as continuous earth wire connected to main earth and earth dolly complete all as specified for the following;- (a) One light point controlled by one switch 5 Amp.
(b) One ceiling fan/exhaust fan point controlled by one switch 5Amp
(c) One socket out let 5Amp controlled by one switch on same board.
(d) One socket out let 5 Amp controlled by one switch on independent board.
(e) One bell point 5 Amp controlled by one bell push on independent board.
(f) One light point controlled by two, 2way switchs5 Amp
All as per item here in before but point wiring with 2.5sqmm FRLS multi stranded copper conductor cable for main circuit and 2.5sqmm cable as earth continuity conductor for one 15Amp socket out let controlled by one 15Amp switch on independat board.
S&F switch piano flush type 5 Amps single pole one way complete,
S&F Socket outlet 2 in 1, 3 pin, 5A flush type complete.
S&F switch socket combination 2 in 1, 3 pin, 5 Amp flush type complete.
S&F switch socket combination 2 in 1 5 pin 5 /15 Amps flush type complete.
S&F of ceiling rose 3 terminal complete PVC/Polycarbonate isolated boly complete all as specified and directed.
S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc as required all as specified and directed.
S&F bell push piano type 5 Amps complete.
S&F switch piano flush type 5 Amps 2 way complete.
S&F electric bell ding dong 230 volt AC complete,
S&F sheet metal enclosure distribution board SPN 8 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail complete incl taking out existing UNSV DB with MCBs.
S&F sheet metal enclosure double door for distribution board factory made for MCB DB load link TPN 4 way suitable for MCCBas incomer, 63 Amp,4 pole. (when MCB's are to be used) with suitable size of busbar complete,fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification including taking down all as directed by Engr-in-Charge at site incl taking out of exsing UNSV DB with MCBs.
S&F MCB SPN 40 A to 63 A 10 KA 240 volts "C" series complete
S&F MCB single pole 5 to 32 Amps 10 KA 240 volts "C" series complete
S&F MCB single pole 63 Amp 10 KA 240 volts "C" series complete
S&F MCCB 63A 4Pole 16KA 415 Volt with fixed magnetic and fixed thermal setting complete.
Supply, laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavy duty with aluminium conductor LT 1100 V grade cross sectional area 25 Sqmm 4 core, complete all as specified and directed by Engineer-in-Charge
Excavation in trenches in any type of soil not exc 1.5 mtr in depth and 1.5 mtr wide and getting out for laying of cables.
Returning and filling in including spreading, leveling , watering and well ramming in layers not exceeding 25 cm thick excavated earth complete all as specified and directed.
Removal of surplus soil to a distance not exceeding 50 mtr and depositing at a level not exceeding 1.5 mtrs above the starting point complete all as specified and directed.
M&L for well burned bricks , laid flat ( old size) sub class B designation '75' for cable protection copmplete all as specifed and directed.
Sand cushioning to under ground cable laid in trenches for laying of LT UG cables 8 cm depth before laying the cable and 15 cm after laying and punned down to a depth of 10 cm as per MES SSR Part-I (2009) all as specified and directed. Note: Punned thickness shall be measured and paid to the contractor.
M&L for sub main wiring with two single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 6 Sq mm drawing through and including concealed rigid non metallic PVC conduit medium grade ISI marked 20 mm dia including one single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 6.0 sq mm as earth continuity conductor connected to commen earth and earth dolly complete incl taking out existing UNSV service connections.
M&L for sheet steel box fabricated out of 2 mm thick CRCA sheet powder coated of size 60x60x25 cm duly compartmentalized suitable to accommodate 4 Nos Energy Meter independently. each compartment shall be provided with suitable door and 2 Nos fancy lock, complete, all as specified and directed by Engr-In-Charge incl taking out existing wooden meter box.
M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire mesh of 22 gauge, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI pit shall be filled with charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) as specified including provision of 15mm dia medium grade GI pipe for earth wire protection and 20 mm dia for watering complete , all excavation and earth work & connecting the earthing to an earthing test point / main switch board as specified and testing on completion complete.
BHARTI CONSTRUCTIONS
M/S CJ CONSTRUCTIONS
M/S ROMESH KUMAR SHAN
U K Engineering Works
R.K. Works
ASHOKA ENGINEERS AND BUILDERS
Bidder Name
BHARTI CONSTRUCTIONS
U K Engineering Works
ASHOKA ENGINEERS AND BUILDERS
R.K. Works
M/S CJ CONSTRUCTIONS
ASHWANI KUMAR KHAJURIA AND SONS
M/S ROMESH KUMAR SHAN
stage.html
html • 0.06 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .