PROVISION OF 2 Nos 11 KV SUB STATION FOR IMPLEMENTATION OF MAFI PROJECT AT INS HANSA UNDER GE NW VASCO

Amount

Total amount of Sch 'A' Part-I (BUILDINGS & STRUCTURES) brought forward from Serial Page No.40 (R)

Total amount of Sch 'A' Part-II (EXCAVATION, EARTH WORK & SITE CLEARANCE) brought forward from Serial Page No.42

Total amount of Sch 'A' Part-III (SEWAGE DISPOSAL ) brought forward from Serial Page No.44

Total amount of Sch 'A' Part-IV (ACCESS ROAD ) brought forward from Serial Page No.46

Total amount of Sch 'A' Part-V (FENCING WORK) brought forward from Serial Page No.50

Total amount of Sch 'A' Part-VI (HARD STANDING) brought forward from Serial Page No.53

Total amount of Sch 'A' Part-VII (LIGHTENING PROTECTION) brought forward from Serial Page No.54

Total amount of Sch 'A' Part-VIII (INTERNAL WATER SUPPLY) brought forward from Serial Page No.56

Total amount of Sch 'A' Part-IX (INTERNAL ELECTRIFICATION) brought forward from Serial Page No.58 ( R )

Total amount of Sch 'A' Part-X (EXTERNAL WATER SUPPLY) brought forward from Serial Page No.60

Total amount of Sch 'A' Part-XI (EXTERNAL ELECTRIFICATION) brought forward from Serial Page No.63

Sch 'A' Part- XII- MISCELLANEOUS ITEMS (Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.)

ACCESS ROAD

S & F RPM (Raised Pavement Marker) Cat eyes of one side prismatic retro reflective lens type of 11.50 cm x 7 cm x 1.6 cm in ASA plastic housing to be fixed with special adhesive on bituminous concrete pavement including test certificate from approved lab complete all as directed and approved by GE.

M&L Providing and laying 2.5mm thick (exclusive of surface applied glass beads) hot applied thermo plastic compound including reflector rising glass beads @ 250 gm per sqm area as per IRC 35, including leveling to uniform surface free from streaks and holes etc. complete all as specified and directed as per MORTH specification 803.

FENCING WORK

M&L for preparation of steel surface and applying one coat of red oxide zinc chrome primer and two coats of Epoxy anticorrosive paint over 10 cm width or girth all as specified and as directed

M&L for preparation of new plastered surface and applying two coats of acrylic anti-fungal weather proof exterior grade paint of first quality over a coat of primer in chequered painting red or white all as specified and as directed.

LIGHTENING CONDUCTOR

M&L for earthing complete with GI earth plate electrode 600mmx600mmx6mm thick, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of earth plate not less than 1.5 m below normal ground level connected with GI earth strip 32mmx6mm thick and GI bolts, nuts, etc and protected by GI pipe light grade 40mm bore and 20 mm dia GI tubing light grade with funnel for watering, connecting to test point, all as shown in electrical plate No.3 of SSR Part I including necessary earth work and excavation in any type of soil, PCC earth chamber with RCC cover slab, salt, charcoal and MS hook, and provision of test point complete. NOTE : GI strip 32x6mm upto 7.5 m shall be included in quoted rates and beyond 7.5 m shall be measured and paid separately.

INTERNAL ELECTRIFICATION

M&L for earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion

S&F LED tube light fitting and tube light 1 x 18 Watts 4 feet long , 230V indoor decorative aluminum extruded LED integrated batten, complete with all accessories internally pre- wired and including connecting up with twin core twisted flexible copper conductor cable with suitable sizes complete all as specified and as directed

S&F Exhaust fan of size 300 mm , 70 W, 1400 RPM, with the air delivery of 1300 CMH complete all as specified and as directed

S&F Ceiling fan 1200 sweep, 50 W, 340 RPM suitable for air delivery of 210 CMM along with down rod of 266-300 mm length complete all as specified and as directed

S & F MCB SP 6 to 32 Amps 240 Volts all as specified and as directed

S & F MCB SPN 6 to 32 Amps 240 Volts all as specified and as directed

EXTERNAL WATER SUPPLY

Construction of valve chamber of size 600x600x600mm (PCC block) internal size suitable for valves with PCC 1:4:8 type D 2 for foundation and brick wall in cement mortar 1:4 PCC 1:2:4 type B 1 for coping rendering in cement mortar (1:4), 15mm thick including Provision of mild steel sheet cover 3.15mm thick on 40x40xx6mm angle iron frame work with two coats of synthetic enamel black paint over a coat of red oxide primer and locking arrangement including necessary excavation earth work all as specified and as directed

EXTERNAL ELECTRIFICATION

Supply, installations, testing and commissioning of distribution transformer mounted on masonry platform step down 11KV 0.433KV, Three phase complying with IS:1180/IEC -76 (part-1) 2014 with latest amendments, indoor type copper wound suitable for 50 Hz system of capacity 630 KVA, oil immersed naturally cooled delta connected on HT side and star connected on LT side, vector group Dyn 11 , provided with OFF load tap changer to vary secondary voltage from -7.5% to +7.5% in step of 2.5% losses should be confined to the limits specified as follows : maximum allowable losses at full load (100%) & Half load (50%) shall not be exceeded 0.98 % and 0/70 % respectively as per GRIHA Rating, percentage impedance 5% . Losses and impedance are subjected to tolerance as specified in IS 1180. The transformer should be supplied with first filling of oil confirming to IS 335. The transformer should have both side cable end boxes with neutral brought out complete al as specified and directed by Engr-in-charge, and installation of transformer shall be carried out as per IS 10028 and comprising with the following standard fittings/Technical specifications. (at MAFI S/S No-01) Note : - (a) Lifting lug for transformer and tank. (b) Earthing terminal rating and diagram plate. (c) Air release device. (d) Oil filling inlet pipe with plug. (e) Drain outlet pipe with brass gate valve. (f) conservator tank with oil level indicator (g) Silica jel breather. (h) Thermometer with pocket (j) Oil and winding temp guage (k) Buchholz relay and alarm trip contacts. (l) explosion vent double diaphram

All as per item No 25 here in before but of capacity 200 KVA (at MAFI S/S No-02) all as specified and as directed

Supply, install, testing and commissioning of oil cooled isolation transformer indoor type of capacity 630 KVA, 3 phase, 50 Hz copper wounded oil cooled, class of insulation A metallic body duly powder coated designed for input voltage range 415 +/- 5% and output voltage range 415 +/- 5% voltage, ratio 1:1, vector group, Dyn 11, Delta-star type, IP 42 protection with first filling of transformer oil of required dielectric strength up to level, efficiency more than 95% separate neutral bushing shall be brought out for earthing potential difference between neutral to earth less than one volt with all standard fitting like digital temperature meter, adequate number of cooling radiators, lifting hooks, earthing terminal two Nos as per IS-9815 (Part I & II (1994) complete with over load/short circuit protection and necessary civil work for foundation as per manufacturer's instructions complete all as specified and as directed. (at MAFI S/S No-01)

All as per item No 27 here in before but of capacity 200 KVA (at MAFI S/S No-02) all as specified and as directed.

Supply and fix servo voltage stabilizer for 'Automatic Controlling / Regulating of Voltage between 300 V to 480 V with output voltage stabilized at 415 with accuracy ± 2.5% and speed of correction 8 Volts per second and of capacity 630KVA Comprising Auto Transformer, Buck & Boost Transformer(Copper Wound with New Filtered & Dehydrated Transformer Oil), Servo Motor, Auto Controlled Solid State Control Circuit (suitable for supply from D.G. Sets also) and other Fittings & Accessories as under:- Voltmeter (0-300 V) to read input/output voltage per phase, Mains/Low/High limit Indicators, Manual Increase/Decrease Push Switch, Auto/Manual mode control switch and output adjustment. automatic operation, three phase, naturally oil cooled, indoor type & designed for input variation between 300 V to 480 V with output voltage stabilized at 415 with accuracy ± 2.5% and speed of correction 8 Volts per second and of capacity 630KVA (at MAFI S/S No-01)

All as per item No 29 here in before but of capacity 200 KVA (at MAFI S/S No-02) all as specified and as directed Notes for Item No 29 & 30: (a) Output voltage stabilized at designed/desired voltage 415 +/- % (b) Overload short circuit protection. (c) High/Low voltage cut off. (d) Manual by pass arrangement in case of emergency.

Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 mpa working pressure for laying of HT UG Cable under hard standing / road crossing / dispersal area) all as specified and as directed

Supplying, erecting, installation, connecting, testing and commissioning of 2 mm thick sheet steel clad , dust and vermin proof free standing 6 Nos Vacuum circuit Breaker panel board of 11 KV, 350 MVA , 630 Amps, VCBs having 2 Number incoming VCBs of 630 Amps, 350 MVA with a set of isolating plug and socket, trip free spring charged 220 volts, AC motor operated closing mechanism with 2 Nos bus coupler and 2 Nos outgoing 630 Amps , VCBs 350 MVA & a shunt trip coil suitable for 24 volts DC complete as detailed out in attached specifications as required. - (two incomer+02 Nos as outgoing+02 Nos as bus coupler = 06 Nos VCBs at Sub station No-01) (i) 11 KV triple pole vacuum circuit breaker horizontal draw out type vertical isolation of rated current 630 Amps , 350 MVA and fitted with:- (a) 3 Nos LED indications Lamp for VCB -ON , Trip circuit healthy & Auto trip (b ) Manual push buttons for VCB off, VCB ON & for trip alarm cancellation. (c) Shunt trip coil (d) 3 Number current transformers 40-20/5-5 Amps class 5p10 for protection having burden 100 VA and class 1 for metering having burden 30 VA. (e) Non draw out potential transformers of ratio 11 KV /110 volt with HT and LT fuses.

(f) Digital flush type class 1 or better accuracy multifunction meter showing V, A, KWH etc. (g) 1 set of three phase R,Y, B indicating lamps along with 2A SP MCB backup protection. (h) Triple pole non- directional IDMT relays having minimum 02 element for over current setting 50%-200% and one element for earth fault protection setting 20%-80% with instruments high set element (j) Master Trip relay -1 in each breaker (k) Cable box suitable for 2 Nos three core 300 sq mm XPLE cables. (l) One set inbuilt DC power pack. (m) Strip heater with thermostat to prevent absorption of moisture. (n) TNC Switch-01 BUSBAR 630 Amps 3 pole aluminum Bus Bar 11 KV, 350 MVA BUS Coupler 2 Nos 630 Amps 3 pole VCB 11 KV 350 MVA Two Nos Outgoing VCB:- (a) Specification all as per incoming VCBs except master trip relay (b) Auxiliary relay - 1 in each breaker

All as per item No. 32 here in before but for MAFI Sub Stn No-02 (two incomer + 02 Nos as outgoing + 02 Nos as buscoupler = 06 Nos VCBs) all as specified and as directed

All as per item No. 32 here in before but for MAFI MRS (two incomer + 02 Nos as outgoing + 02 Nos as buscoupler = 06 Nos VCBs) all as specified and as directed

Supply, install ,testing and commissioning SF6 insulated compact Outdoor type R.M.U. rated voltage 11 KV,rated current 630 A, short circuit breaking current 16 KA and making capacity 40 KA ,fully arc proof metal enclosed, free standing, floor mounting, flush fronted type consists of manually operated non draw out type SF6 module-1 Nos load break switches (Incomers) and 2 No. Vacuum circuit breaker (outgoing) with integrated relays and related CTs as specified below, cable switch module and an interlocking mechanism with the earthing switch all as specified and directed. Degree of protection shall be as per manufacturer specifications. (a) Fixed type voltage indicators and electronic short circuit indicators for simple fault indication (b) Resin cast CT with ratio 75/1-1 with 15VA burden class1 for metering and class 5 P10 for protection-Set of three (c) Resin cast potential transformers with ratio 11KV/1.732, 110V/1.732, 200 VA class1 with HT fuses mounted on with drawable rack (d) Self powered microprocessor controlled numeric relay comprising of three over current , one earth fault protection relay with high set for both phase & earth and with fault memory, universal auxiliary supply

Supply and fixing cable route indicator made out of 15x 15x 6 mm thick MS plate welded with 8 mm x30 cm long MS rod grouted in PCC block of size 0.2x0.2x0.3(LXWXH) and writing HT cable complete all as specified and as directed. Note : The quoted rate is inclusive of GI bracket and connected items

Supply & fixing street light fitting LED 60 W, and other accessories for mounting on pole all as specified and as directed Note: The quoted rate is inclusive of GI bracket of suitable dia and length and connected items.

Supply & install octagonal hot dipped galvanised mild steel pole with grey powder finish 6.0 meter long complete with base plate and finial including foundation complete all as directed by Engineer-in-Charge for street lights

Rubber mat of 1 meter x 2 meter x 10 mm all as specified and as directed

Rubber mat of 1 meter x 2 meter x 19 mm all as specified and as directed

MCCB 63 Amps 4 Pole 25 KA - 2 Nos Extended ROM suitable for 63 Amp MCCB - 2 Nos Spreader Terminal suitable for 63 Amp MCCB - 2 Nos MCCB 32 Amps 4 Pole 25 KA - 11 Nos Extended ROM suitable for 32 Amp MCCB -11 Nos Spreader Terminal suitable for 32 Amp MCCB - 11Nos MCCB 25 Amps 4 Pole 25 KA - 5 Nos Extended ROM suitable for 25 Amp MCCB - 5 Nos Spreader Terminal suitable for 25 Amp MCCB - 5 Nos MCCB 160 Amps 4 Pole 25 KA - 2 Nos Extended ROM suitable for 160 Amp MCCB- 2 Nos Spreader Terminal suitable for 160 Amp MCCB - 2 Nos MCCB 16 Amps 2 Pole 25 KA - 8 Nos Extended ROM suitable for 16 Amp MCCB - 8 Nos Spreader Terminal suitable for 16 Amp MCCB - 8 Nos MCB TPN 32A C-Curve 10 KA - 2 Nos

M&L for Automatic power factor control (APFC) panel of capacity 200 KVAR, 3 phase 415 volt indoor type made out of 2mm thick CRCA sheet and suitable for fixing Capacitor (ultra heavy duty capacitor is having over current withstand capability as 3Xin, peak thrush current withstand capability) 200 KVAR 8 step (1x5 + 2x10 +3x25 + 2x50), contactor, APFC relay and power factor meter, making bank connection with suitable size of copper wire, copper bus bar, using angle iron 50 x 50 x 6mm frame (bottom portion of panel), grouted by PCC foundation with 1:2:4 type C1 with 20mm graded stone aggregate thimbles and cable entry boxes with cable gland including locking arrangement, painting with two coat of synthetic enamel paint over a coat of red oxide primer complete with the following :- (a) MCCB 4 pole 315 Amps of 35 KA - 01 No. (b) Contactor of suitable capacity (c) APFC Relay - 01 No. (d) Power factor meter - 01 No. (e) MCBs as per manufacturer specification (f) Indicator lamp LED type - 01 set with 200 ((1x5 + 2x10 +3x25 + 2x50)

All as per item No 48 here in before but of capacity 80 KVAR with following :- (a) MCCB 4 pole 100 Amps of 25 KA - 01 No. (b) Capacitor (5+5+10+10+10+10+10+20) (c) Contactor of suitable capacity (d) APFC Relay - 01 No. (e) Power factor meter - 01 No. (f) MCBs as per manufacturer specification (g) Indicator lamp LED type - 01 set

Supply & Fix reflective informatory sign boards box type with LED lighting, single side writing as per IRC 67 made of high intensity grade sheet , fixed over GI sheet 1.5 mm thick, supported on angle iron to fixed on wall, including all necessary welding and painting with two coats over a coat of primer complete all as specified and as directed by Engineer-in-Charge

Supply and fix 3 KVA UPS for 30 min back up single phase AC input 160 to 260 V and out put 230 ± 1%, housed in sheet metal enclosure of protection class IP 21 consisting of following parameters:- a) Single Phase Output Inverter (230VAC±1%, 1Ph, 2Wire, 50Hz±0.5%) b) Line & Load Regulation: ±1% Phase to Neutral c) Max Output Current: 10 AMPS RMS at load PF @0.8 d) Output Voltage Distortion: <2% for Linear Load e) Inverter Technique: IGBT Based PWM f) Output Overload Capacity: 150% for 10 Seconds g) Transient Response for 100% Step Load: ±5% h) Overall AC to AC Efficiency: ≥88% at Full Load & Nominal Input Voltage

i) Galvanic Isolation: Input & Output Isolated by Inbuilt Double Wound Isolation Transformer j) UPS enclosure with protection class IP21 & Structured Black finish k) Ambient Temperature: Up to 45°C l) Protections: Input Over/Under Voltage, Phase fail, Output Overload, Output Over/Under Voltage, DC Over/Under Voltage, High speed fuses for semi conductor devices & Overheat m) Front Panel Display & Indications: LCD Display to show Input Voltage, Output Voltage, Output Current, Output Frequency & Battery Voltage. LED Indications to indicate Mains On, Output on & Fault. Nature of fault will be displayed in text form on display n) SMF Batteries of 12V/18AH – 15Nos to provide 30 minutes stand by time with suitable MS Powder coated open rack, inter connecting links, & UPS to Battery Cable of 5 Mtrs length

M&L for Chemical earthing with one No of copper earth plate of size 900 x 600 x 5 mm & copper earth strip 32 x 6 mm buried in ground vertically to a depth not less than 3.0 m below ground level with top edge earth electrode at a depth not less than 2.40 m deep below ground level including suitable quantity of backfill chemical compound for filling in each pit to cover earth electrode minimum 100 mm all around and electrode shall be jointed with the copper strip of size 32 x 6 mm by exothermic weld complete with earth pit chamber of size 300 x300 mm and RCC cover for demarking the location of earth electrode location. Make of Back Fill Compound: Tercel (Isogel) (Australia)/ Indelec (Xgel) (France)/ ERICO (GEM) (USA)/ LPF (Reslo) (Australia) (Note :- (i) The quantity of Backfill compound and depth of earth pit can be increased by the contractor without any extra cost to Govt. The Contractor shall ensure that earth resistance shall be less than 1 ohms on completion and testing. The testing of each earthing shall be carried out in presence of Engineer-in-charge and test results shall be submitted duly signed by all concerned while claiming payments.) (ii) Earth strip with protection pipe 50mm GI light grade up to 7.5 meter is deemed to be included in the rates quoted.

United Sales Corporation

Horizon Construction

UNITED TECHNO PROJECTS PVT LTD

Bhanwariya Infra Projects Pvt Ltd

REWINDER TECHNO ELECTRICALS