SPECIAL REPAIR TO JOINERY, PLASTER AND OTHER MISC WORK IN GIRL CDT BLOCKS (12 BLOCK) AT DG NCC UNDER GE (EAST) DELHI CANTT-10

Amount

Demolition of cement concrete (reinforced) of any position not otherwise specifically provided for and including reinforcement required to facilitate demolition upto and including fourth story and on the roof top/mumty/parapet and removal of debris and rubbish out side MoD land complete all as specified & directed.

Demolition of brick work built in cement mortar in any description and position complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15cm thickness ( below or above ground level ) including removal of rubbish out side complex (MOD land), complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) laid bedded and pointed in any mortar and removal of old tiles from premises complete all as specified and directed.

Taking down chowkhat or frames exc. 1.5 Sqm and n.exc 4 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed.

Taking down chowkhat or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed.

Taking down cement plaster, terrazzo, grit plaster dado in any thickness from brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc including removal of rubbish, vegetation etc outside complex (MOD land) complete all as specified and directed.

M& L for powder coated anodised aluminium door shutter, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, powder coated handles 2 Nos in each shutter, hinges, powder coated aluminium snap beading screws,150mm long tower bolt (2 no) etc. complete all as specified & directed

S&F Powder coated aluminium window and ventilator shutters, side hung type with/without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.),150mm long tower bolt (2 no) complete all as specified & directed

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for frame of doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket/ rendering etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws complete as per architectural drawings and the directions of Engineer-in-Charge

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening complete as per requirement and direction of Engineer-in- charge.

M&L for powder coating of any colour (Thickness or powder coating not less than 50 micron) for aluminium grill of any size or shape complete all as specified & directed

S&F for 4mm thick sheet glass, ordinary quality and glazing in square n exc 0.5 sqm in each pane complete all as specified & directed

S& F for wire netting of stainless steel wire 0.91mm dia and size of mesh 12mm fixed with tinned tacks of stainless steel wire staples/ screws complete all as specified & directed

M&L for Brick work with sub class 'B' bricks straight or curved on plan to any radius built in CM 1:6 complete all as specified and directed.

M&L for mild steel TMT bars of 10 mm dia and over cut to length bent to shape required including cranking, bending etc and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed.

M&L for RCC (1:2:4) Ty B-1 using 20mm graded stone aggregate as in Chajjas, deck slabs and in shelves and the like complete all as specified & directed

Supply only liquid water proofing compound complete all as specified and directed.

M & L 16-18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and incl 15mm thick CM (1:4) including notching, moulding and polishing and dismantling of existing stone of any type complete all as specified and directed..

M & L for glazed ceramic tiles in vertical surface of size 300mmx450mm or 300mmx600mm and 7-8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over & incl 10mm thick screed bed in CM 1:4 after dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and as directed .

M & L for glossy finished coloured chequered cement concrete tiles 30cm x 30cm x 20-22mm thick, set, jointed and pointed in neat cement slurry over & including15mm thick screed bed in CM 1:6 and dismantling of old existing tile of any description or thickness complete all as specified & directed

M&L rendering 12 mm thick in CM 1:6 on fair face of brick work/ concrete surfaces (either surfaces) and finished even and fair complete all as specified & directed

M&L rendering 15 mm thick in CM 1:4 on fair face of brick work/ concrete surfaces with water proofing compound finished even and fair complete all as specified & directed (Note :- WPC shall be measured and paid separately under relevant items of this Sch/BOQ as Supply only)

M&L Cement concrete 1:2:4 type B0 (using 12.5mm graded crushed stone agg) as in coping including demolition of existing PCC complete all as specified and directed

M & L for preparation of new plastered surfaces of internal wall/ceiling and applying 2 coats of oil bound distemper over and including 2mm thick wall care putty and coat of interior primer complete all as specified and directed.

M & L for preparation of old treated plastered surfaces of internal wall/ceiling and applying one coats of oil bound distemper over a coat of 1mm thick wall putty complete all as specified and directed.

M & L for preparation of new plaster external wall and ceiling surfaces of and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm and 2mm thick wall care putty complete all as specified and directed.

M&L preparation of old plastered external wall & ceiling surfaces and apply one coat of exterior emuslion paint complete all as specified & directed

S & F designer board false ceiling of size 600x600x4mm thick E-Board white pre-laminated sett embossed reinforced tiles of approved texture at all height laid on Hot dipped Galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick GS sheet and of size 24x32x3000mm and spaced at 1200mm centers securely fixed to the structural soffits by approved hangers at 1200mm maximum centers. Hangers of GI wire 2mm dia to be fixed by approved rawl plug, level and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall. Flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runners at 600mm center to form 1200x600mm modules cross tee longer than 600mm to be supported independently. 600x600mm modules to be formed by fitting 600mm long cross Tee centrally between the 1200mm cross tee. Tee, Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour all as per manufacture instruction including taking down the existing false ceiling of any type with frame work complete all as specified and directed.

Taking down/ out carefully copper/aluminium point wiring for light/fan/bell/ sockets 5/15 Amps complete without accessories as switches, Sockets, holders, ceiling roses, light fitting regulators etc (to be measured and paid separately under relevent item of this Sch as S&F in repair and credit for these item given in credit schedule here-in-after) and making good the disturbed surface all as directed.

M&L point wiring complete with 1.5 Sq mm (nominal area) FRLS PVC insulated sheathed and multistranded copper conductor cable ISI marked and including PVC concealed conduit ISI marked of size 20 mm dia medium grade and fittings such as tees, bends, elbow, and FRLS PVC insulated unsheathed 1.5 Sqmm copper conductor mulistranded earth wire, connecting to common earth dolly including Metal Flush Box, Cover plate with frame, cutting chases and making good disturbed surface in CM 1:3 to match with existing surface for one light point exhaust fan point controlled by one 1-way switch complete all as directed. (a) One light point /fan point /wall fan point/bell/buzzer contolled by one 1-way switch /bell push

(b) one socket outlet point 5 amps on the independent board.

S&F in replacement ceiling rose surface bakelite 65x50mm Three terminals, 240 V grade complete all as specified and directed. Make- Anchor/Cona/Kinjal

S&F in replacement modular switch 6Amps, 1 module complete all as specified and directed. ,Make-Indoasian shynora,Anchor Roma,Legrand Arteor or equivalent.

S& F in replacement modular socket out 6Amps, 2 module complete, Make-Indoasian shynora,Anchor Roma,Legrand Arteor or equivalent.

S&F in replacement LED luminaire 600 mm x 600 mm, 36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

S & F in replcement surface and wall mounted LED tube light fitting with Aluminium housing & interated electronic driver with tube rod of 20 Watt. slim elegant design.and including connected with 3 core 23/0.0076 insulated copper wire from celing rose to fittting connector all as specified and directed.

S & F in replacement LED energy efficient integrated battens fittings, Aluminium extruded heat sink with shatter proof opal shell of Aluminium housing, 10 Watts, cool/warm white as per site requirement, complete all as specified and directed.

S&F in replacement sheet metal enclosure single pole and neutral 8 way double door including taking down old unsv MCB DB any way complete all as specified and directed.. Make ABB/ Legrand /Schnieder

S&F Amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) SP of 6 to 32 Amps capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed. Make :- ABB/ Legrand /Schnieder

S&F Isolator 40 Amp rating 240V in the MCB DB complete with connection testing and commissioning complete all as specified and directed. Make :- ABB/ Legrand /Schnieder

S & F in replacement energy efficicent LED fittings 45W LED 6K suitable for builing security light pressure die cast aluminium roadway luminaire with high power LEDs and HF electronic driver complete all as directed.

S&F in replacement of street light fitting bracket, 1.0 mtr long bent to shape made out of galvanized iron pipe of 25 mm dia size light grade complete with nut, bolts, washer, clamps etc inclusive of one primer coat, one under coat and one finishing coat of silver paint complete all as specified and directed.

M&L earthing with galvanised steel plate electrode 600 x 600 x 6 mm thick, buried directly in ground( earth pit not less than 2.25m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level , connected to and including galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, washers of galvanised steel earth strip protected by and including 20 mm bore “light grade” and connected to main test point as directed and including concrete pit in PCC(1:3:6) type C1 precast RCC M-25 (design mix) precast cover slab (54 x 54 x 5 cm) duly reinforced with and including 8 mm dia TMT steel bars @ 150 mm C/C both way, one lifting handle made of 8 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm bore GI medium grade pipe for watering, charcoal and salt in alternate layers, including necessary excavation and earth work any type of soil complete all as specified and shown in electrical plate No. 5 of SSR Part –I including testing on completion complete all as specified and directed.

garnet engineers contractors (BID ID -3370044)

M/s Durga Traders (BID ID -3364973)

THE LOTUS BUILDTECH (BID ID -3369202)

M/s Shubh Enterprises (BID ID -3371419)

M/S Rohit Enterprises (BID ID -3371709)

Atish Builders LLP (BID ID -3364911)