PERIODICAL SERVICES TO ALL BUILDINGS DUE AT MPF AMBERNATH

M & L for Distempering in Two Coats over wall surface including following procedure: (i) Preparation of old painted surfaces plastered or unplastered, it shall be ensured that the surface to be painted must be free from any loose paint, dust or grease. Any previous growth of fungus, algae or moss shall be removed thoroughly by vigorous wire brushing and cleaning with water. Surface imperfection such as holes, removal of nails, dents fine cracks etc. should be filled with wall putty. (Make: JK / Birla White wall Putty) [The surface such prepared shall be shown to SIC & EIC for inspection before application of Primer] (ii) Apply one coat of primer as per Manufacturer's Specifications (Make: 1st quality wall primer as approved by Competent Factory Authority from Asian Paints / Birla Opus Paints / Nerolac Paints / Berger Paints ) and allow the primer coat to dry for 4 hours. [The surface after application of Primer shall be shown to SIC & EIC before application of 1st coat of Distemper] (iii) Applying two coats of Acrylic distemper (Make: 1st quality Acrylic Distemper as approved by Competent Factory Authority from Asian Paints / Birla Opus Paints / Nerolac Paints / Berger Paints) as per Manufacturer's specification. The application shall be done by using brush / roller. Stir the paint well before use. A gap of 4-6 hours should be given between two coats. All the above works shall be carried out at any height including necessary scaffolding, staging and all safety precautions with necessary safety equipments, including complete cleaning of site and removal of all rubbish outside Factory Premises etc, all complete as directed by Engg-in-Charge. [The surface after application of 1st Coat shall be shown to SIC & EIC for inspection before application of 2nd Coat of Distemper. Subsequently the surface after application of 2nd Coat shall be shown to SIC & EIC for final inspection. Necessary rectification works / re coating work for achieving desired finish shall be made by the Contractor at own risk & cost until the surface is finished to the entire satisfaction of the EIC / Competent Factory Authority] Important Note1: The Bidder shall specify the make and trade name of the Primer and Distemper among the specified makes mentioned in the specification in the Technical Bid as per prescribed format which shall be used during the work by the Bidder. The Bidder will not be considered as Technically qualified if he / she fail to submit the make and trade name in the Technical Bid. Important Note2: The Bidder shall note & shall strictly adhere to the Specification of the works and Points given below for Work Procedure and Materials to be incorporated in the work, before quoting for the Item. It shall be presumed that Bidder has clearly understood the Specification of the works and points regarding materials & Work procedure and shall carry out the work at quoted rates strictly adhering to the Specifications and points regarding Materials & Work procedure.

M & L for Distempering in Two Coats over Ceiling surface including following procedure: i. Preparation of old painted surfaces plastered or unplastered, it shall be ensured that the surface to be painted must be free from any loose paint, dust or grease. Any previous growth of fungus, algae or moss shall be removed thoroughly by vigorous wire brushing and cleaning with water. Surface imperfection such as holes, removal of nails, dents fine cracks should be filled with wall putty. (Make: JK / Birla White wall Putty) [The surface such prepared shall be shown to SIC & EIC for inspection before application of Primer] ii. Applying two coats of Acrylic distemper (Make : 1st quality Acrylic Distemper as approved by Competent Factory Authority from Asian Paints / Birla Opus Paints / Nerolac Paints / Berger Paints) as per Manufacturer's specification. The application shall be done by using brush / roller. Stir the paint well before use. A gap of 4-6 hours should be given between two coats. All the above works shall be carried out at any height including necessary scaffolding, staging and all safety precautions with necessary safety equipments, including complete cleaning of site and removal of all rubbish outside Factory Premises etc.all complete as directed by Engg-in-Charge. [The surface after application of 1st Coat shall be shown to SIC & EIC for inspection before application of 2nd Coat of Distemper. Subsequently the surface after application of 2nd Coat shall be shown to SIC & EIC for final inspection. Necessary rectification works / re coating work for achieving desired finish shall be made by the Contractor at own risk & cost until the surface is finished to the entire satisfaction of the EIC / Competent Factory Authority] Important Note1: The Bidder shall specify the make and trade name of the Primer and Distemper among the specified makes mentioned in the specification in the Technical Bid as per prescribed format which shall be used during the work by the Bidder. The Bidder will not be considered as Technically qualified if he / she fail to submit the make and trade name in the Technical Bid.) Important Note2: The Bidder shall note & shall strictly adhere to the Specification of the works and Points given below for Work Procedure and Materials to be incorporated in the work, before quoting for the Item. It shall be presumed that Bidder has clearly understood the Specification of the works and points regarding materials & Work procedure and shall carry out the work at quoted rates strictly adhering to the Specifications and points regarding Materials & Work procedure

M & L for External painting in Two Coats including following procedure: i. Preparation of old painted surfaces plastered or unplastered, it shall be ensured that the surface to be painted must be free from any loose paint, dust or grease. Any previous growth of fungus, algae or moss should be removed thoroughly by vigorous wire brushing and cleaning with water. Surface imperfection such as holes, dents fine cracks should be filled with exterior wall putty, (Make: 1st Quality exterior wall putty form JK / Birla / Asian Paints / Birla Opus Paints / Berger Paints / Nerolac Paints) a mixture of white cement and fine sand in proportion 1:3 may be used for large imperfections / cracks as directed by EIC. [The surface such prepared shall be shown to SIC & EIC for inspection before application of Primer] ii. Applying one coat of Exterior Wall Primer (Make: 1st quality exterior wall primer as approved by Competent Factory Authority from Asian Paints / Birla Opus Paints / Nerolac Paints / Berger Paints) as per Manufacturer's Specifications. The exterior primer shall be applied @ minimum 0.90 Litre / 10 Sq.m. The primer coat shall be allowed to dry for 4 hours. [The surface after application of Primer shall be shown to SIC & EIC before application of 1st coat of Exterior Emulsion] iii. Finishing walls with ready mixed Premium Acrylic Emulsion paint (Company Depot Tinted) having VOC less than 50 gm / litre and UV resistance as per IS 15489:2004, Alkali & Fungal resistance, Dirt Resistance exterior paint of required shade with silicone additives, Two or more coats applied @ 1.43 litre per 10 Sq.m (Make: 1st quality Weatherproof Exterior Emulsion as approved by Competent Factory Authority from Asian Paints / Birla Opus Paints / Nerolac Paints / Berger Paints ) over and including priming coat of exterior primer applied @ 0.90 litre / 10 Sq.m as mentioned above. A gap of 4-6 hours should be given between each coat. All the above works shall be carried out at any height including necessary scaffolding, staging and all safety precautions with necessary safety equipments, including complete cleaning of site and removal of all rubbish outside Factory Premises etc, all complete as directed by Engg-in-Charge. [The surface after application of 1st Coat shall be shown to SIC & EIC for inspection before application of 2nd Coat of Exterior Emulsion. Subsequently the surface after application of 2nd Coat shall be shown to SIC & EIC for final inspection. Necessary rectification works / re coating work for achieving desired finish shall be made by the Contractor at own risk & cost until the surface is finished to the entire satisfaction of the EIC / Competent Factory Authority] Important Note1: The Bidder shall specify the make and trade name of the Exterior Primer and Premium Acrylic Emulsion Alkali & Fungal resistance, Dirt Resistance exterior paint among the specified makes mentioned in the specification in the Technical Bid as per prescribed format which shall be used during the work by the Bidder. The Bidder will not be considered as Technically qualified if he / she fail to submit the make and trade name in the Technical Bid. Important Note2: The Bidder shall note & shall strictly adhere to the Specification of the works and Points given below for Work Procedure and Materials to be incorporated in the work, before quoting for the Item. It shall be presumed that Bidder has clearly understood the Specification of the works and points regarding materials & Work procedure and shall carry out the work at quoted rates strictly adhering to the Specifications and points regarding Materials & Work procedure.

M & L for preparation of old painted surfaces [The surface after preparation of surface shall be shown to SIC & EIC before application of 1st coat of paint] and Painting on Steel and Iron surfaces of any description by applying two coats of Synthetic Enamel Paint (Make: 1st quality Synthetic Enamel Paint as approved by Competent Factory Authority from Asian Paints / Birla Opus Paints / Nerolac Paints / Berger Paints ) etc all complete at any height including necessary scaffolding, staging and all safety precautions with necessary safety equipments, including complete cleaning of site and removal of all rubbish outside Factory Premises as directed by Engg-in-Charge. [The surface after application of 1st coat of paint shall be shown to SIC & EIC before application of 2nd coat. Subsequently surface after application of 2nd coat shall be shown to SIC & EIC for final inspection. Necessary rectification works / re coating work for achieving desired finish shall be made by the Contractor at own risk & cost until the surface is finished to the entire satisfaction of the EIC / Competent Factory Authority] Important Note1: The Bidder shall specify the make and trade name of the Synthetic Enamel among the specified makes mentioned in the specification in the Technical Bid as per prescribed format which shall be used during the work by the Bidder. The Bidder will not be considered as Technically qualified if he / she fails to submit the make and trade name in the Technical Bid. Important Note2: The Bidder shall note & shall strictly adhere to the Specification of the works and Points given below for Work Procedure and Materials to be incorporated in the work, before quoting for the Item. It shall be presumed that Bidder has clearly understood the Specification of the works and points regarding materials & Work procedure and shall carry out the work at quoted rates strictly adhering to the Specifications and points regarding Materials & Work procedure)

M & L for preparation of old painted surfaces [The surface after preparation of surface shall be shown to SIC & EIC before application of 1st coat of paint] and Painting on Wooden surfaces of any description by applying two coats of Synthetic enamel Paint (Make: 1st quality Synthetic Enamel Paint as approved by Competent Factory Authority from Asian Paints / Birla Opus Paints / Nerolac Paints / Berger Paints) etc all complete at any height including necessary scaffolding, staging and all safety precautions with necessary safety equipments, including complete cleaning of site and removal of all rubbish outside Factory Premises as directed by Engg-in-Charge. [The surface after application of 1st coat of paint shall be shown to SIC & EIC before application of 2nd coat. Subsequently surface after application of 2nd coat shall be shown to SIC & EIC for final inspection. Necessary rectification works / re coating work for achieving desired finish shall be made by the Contractor at own risk & cost until the surface is finished to the entire satisfaction of the EIC / Competent Factory Authority] Important Note1: The Bidder shall specify the make and trade name of the Synthetic Enamel among the specified makes mentioned in the specification in the Technical Bid as per prescribed format which shall be used during the work by the Bidder. The Bidder will not be considered as Technically qualified if he / she fails to submit the make and trade name in the Technical Bid. Important Note 2: The Bidder shall note & shall strictly adhere to the Specification of the works and Points given below for Work Procedure and Materials to be incorporated in the work, before quoting for the Item. It shall be presumed that Bidder has clearly understood the Specification of the works and points regarding materials & Work procedure and shall carry out the work at quoted rates strictly adhering to the Specifications and points regarding Materials & Work procedure)

M & L for preparation of old painted surfaces [The surface after preparation of surface shall be shown to SIC & EIC before application of 1st coat of paint] and painting on steel and iron surfaces by applying two coats of Aluminum Paint (Make: 1st quality Aluminium Paint as approved by Competent Factory Authority from Asian Paints / Birla Opus Paints / Nerolac Paints / Berger Paints) etc all complete at any height including necessary scaffolding, staging and all safety precautions with necessary safety equipments, including complete cleaning of site and removal of all rubbish outside Factory Premises as directed by Engg-in-Charge. [The surface after application of 1st coat of paint shall be shown to SIC & EIC before application of 2nd coat. Subsequently surface after application of 2nd coat shall be shown to SIC & EIC for final inspection. Necessary rectification works / re coating work for achieving desired finish shall be made by the Contractor at own risk & cost until the surface is finished to the entire satisfaction of the EIC / Competent Factory Authority] Important Note1: The Bidder shall specify the make and trade name of the Synthetic Enamel among the specified makes mentioned in the specification in the Technical Bid as per prescribed format which shall be used during the work by the Bidder. The Bidder will not be considered as Technically qualified if he / she fail to submit the make and trade name in the Technical Bid. Important Note2: The Bidder shall note & shall strictly adhere to the Specification of the works and Points given below for Work Procedure and Materials to be incorporated in the work, before quoting for the Item. It shall be presumed that Bidder has clearly understood the Specification of the works and points regarding materials & Work procedure and shall carry out the work at quoted rates strictly adhering to the Specifications and points regarding Materials & Work procedure

M & L for preparation of old surfaces [The surface after preparation of surface shall be shown to SIC & EIC before application of 1st coat of paint], and Painting on Dado, brick , stone, concrete, asbestos cement or plaster surface by applying two coats of synthetic enamel paint (Make: 1st quality Synthetic Enamel Paint as approved by Competent Factory Authority from Asian Paints / Birla Opus Paints / Nerolac Paints / Berger Paints) including necessary scaffolding if required , staging, all safety precautions with necessary safety equipments, cleaning of premises and removal of all rubbish outside Factory Premises etc all complete as directed by Engg-in-Charge. [The surface after application of 1st coat of paint shall be shown to SIC & EIC before application of 2nd coat. Subsequently surface after application of 2nd coat shall be shown to SIC & EIC for final inspection. Necessary rectification works / re coating work for achieving desired finish shall be made by the Contractor at own risk & cost until the surface is finished to the entire satisfaction of the EIC / Competent Factory Authority] Important Note1: The Bidder shall specify the make and trade name of the Synthetic Enamel among the specified makes mentioned in the specification in the Technical Bid as per prescribed format which shall be used during the work by the Bidder. The Bidder will not be considered as Technically qualified if he / she fail to submit the make and trade name in the Technical Bid. Important Note2: The Bidder shall note & shall strictly adhere to the Specification of the works and Points given below for Work Procedure and Materials to be incorporated in the work, before quoting for the Item. It shall be presumed that Bidder has clearly understood the Specification of the works and points regarding materials & Work procedure and shall carry out the work at quoted rates strictly adhering to the Specifications and points regarding Materials & Work procedure)

M & L for rendering average 30mm thick cement plaster in patches at any height and position in CM 1:4 with Neeru finishing matching to existing surface, curing, including staging, scaffolding, all safety precautions with necessary safety equipments and thorough cleaning of site etc all complete as directed by the Engg In Charge. Important Notes: (i) Contractor shall use only clean river sand / washed sand for preparation of cement mortar in proportion 1:4 i.e. one part of cement mixed with 4 parts of clean river sand / washed sand (ii) The cement to be used shall not be more than one month old. (iii) Any one of the make of cement shall be used throughout the work from M/s Ambuja , M/s Ultratech, M/s Birla, M/s ACC (iv) The Plaster shall be applied in Two Coats. Hacking shall be done over 1st coat of plastering to receive second coat. (v) Sample of all materials shall be got approved from the EIC before use in work

M & L for rendering average 30mm thick cement plaster in patches at any height and position in CM 1:4 with sand face finishing matching to existing surface, curing, including staging, scaffolding, all safety precautions with necessary safety equipments and thorough cleaning of site etc all complete as directed by the Engg In Charge. Important Notes: (i) Contractor shall use only clean river sand / washed sand for preparation of cement mortar in proportion 1:4 i.e. one part of cement mixed with 4 parts of clean river sand / washed sand. (ii) The cement to be used shall not be more than one month old. (iii) Any one of the make of cement shall be used throughout the work from M/s Ambuja , M/s Ultratech, M/s Birla, M/s ACC (iv) The Plaster shall be applied in Two Coats. Hacking shall be done over 1st coat of plastering to receive second coat. (v) Sample of all materials shall be got approved from the EIC before use in work