Construction of Paddy Procurement Center at Agarkhandi SCS for Gosani Block in the District of Gajapati (800 Sft Cover Pindi) (Civil, E.I. and P.H)

Earth work in excavation of foundation trenches in all kinds of soil upto the required depth including moorum, stoney earth and earth mixed with boulders except sheet rocks and boulders requiring blasting including dressing, leveling the bed and depositing the excavated materials away from work site with initial leads and lifts, T&P shoring, shuttering and dewatering if required etc, complete as directed by the Engineer-in–charge. [Farmer Rest Shed-66.03+Cover Pindi-64.00+Drying Platform-22.49+Compound Wall-159.45+Internal Road-205.70 = 517.67 Cum]

Filling foundation and plinth & sides of foundation with excavated materials (excluding rock), in layers not exceeding 20 cm in depth including watering and ramming and dressing and leveling the top to proper level, lead up to 50 m and lift upto 1.5 m or gradient including cost of all labour, labour CESS,sundries and T&P etc. complete in all respect as per direction of the Engineer-in-Charege.[Farmer Rest Shed-44.24+Cover Pindi-42.88+Drying Platform-15.07+Compound Wall-106.83+Internal Road-137.82= 346.84 Cum]

Supplying & filling in foundation and plinth with good quality river sand in layers not exceeding 23cm in depth and compacted with watering, ramming, dressed and leveled the top surface to required gradient including cost , conveyance , royaoity,Addl.cost DMF&EMF of all materials, cost of all labour, T&P, etc.required to complete the work in all respect as per direction of the Engineer-in-charge.(Measurement will be taken on finished compacted section only) [Farmer Rest Shed-28.78+ Cover Pindi-18.81 + Drying Platform-41.29+Compound Wall-23.54 + Internal Road-102.85 = 215.27 Cum]

Providing & applying of pre constructional anti-termite treatment by drilling 12mm dia holes at distance of 30cm @ junction of wall & floor about 300mm apart deep enough to reach the soil below & chemical emulsion (IMIDACHLOPRIED 30.5SC mixed with 47.5ltr water) pumped these holes to soak the soil @ 1 ltr solution of each hole as per manufactures specification & the holes should be pluged the filling materials including cost of all materials, labour,conveyance, T&P , all taxes and hire charges of machinaries as per direction of Engineer-in-charge.(make-premise-BAYER,Paxton-FMC,ozie-KALYANI) [Farmer Rest Shed-59.93 Sqm]

Providing and laying cement concrete (1:3:6) in foundation & plinth using 40mm size black hard granite crusher broken metal and screened and washed sharp river sand of approved quality from approved quarry as per approved design including hoisting, lowering, laying and compacting to proper thickness, watering and curing for the required period, finished smooth, providing grooves or beads where necessary including cost, conveyance, royalty,Addl. charges, DMF&EMF of all materials with labour, labour CESS , and T&P etc. required to complete the work in all respect including dewatering if required as per direction of the Engineer-in-Charge. [Farmer Rest Shed-18.30 + Cover Pindi-19.22 + Drying Platform-19.65+Compound Wall-23.54 = 80.71Cum]

Fly ash brick masonry in cement mortar (1:6) in Foundation& Plinth using Fly ash bricks of (23x11x8cm) size having a crushing strength of not less than 75 kg per Sq.cm with dimensional tolerance + 8 percent after immersing Bricks in water till saturation before use , including splays cutting, circular molding, chamfering, corbelling and all similar type of operations with all necessary projections watering, curing etc. complete including cost, conveyance, royalties, Addl.cost DMF&EMF of all materials, cost of all labour, labour CESS T&P etc. complete in all respect as per drawing and technical specifications and as per direction of the Engineer-in-charge. [Farmer Rest Shed-8.61 + Cover Pindi-24.08 + Drying Platform-18.59+Compound Wall-52.5 = 103.78Cum]

Fly ash brick masonry in cement mortar (1:6) in Super structure using Fly ash bricks of (23x11x8cm) size having a crushing strength of not less than 75 kg per Sq.cm with dimensional tolerance + 8 percent after immersing Bricks in water till saturation before use , including splays cutting, circular molding, chamfering, corbelling and all similar type of operations with all necessary projections watering, curing etc. complete including cost, conveyance, royalties,Addl.cost DMF&EMF of all materials of all materials, cost of all labour, labour CESS T&P ,Scaffolding as required etc. complete in all respect as per drawing and technical specifications and as per direction of the Engineer-in-charge. [Farmer Rest Shed-17.04 + Compound Wall-59.85 = 76.89Cum]

Providing, lifting, hoisting and laying Reinforced cement concrete of M-25 grade as per approved designs and drawings having a minimum compressive strength (in work test) 250 Kg. / Square cm. in 15 cm. cubes at 28 days after mixing and test conducted in accordance with I.S. 516 using 12 mm. to 20 mm. size black hard crushed broken granite stone chips and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned ( 20mm. size chips not to exceeds 25 % ) to be mixed in concrete mixture with Portland slag cement (PSC) including hoisting, lowering, laying and compaction concrete by using vibrators, watering and curing for 28 days, centering and shuttering then after dismantling and removing debris from the work site and finishing the exposed surface smooth providing grooves or beads wherever necessary including cost, conveyance, loading, unloading, royalties and taxes of all materials and cost of all labours, sundries, T & P required of the work etc. complete in all respect as directed by the Engineer-in-Charge. But excluding cost and conveyance of M.S. rods or Tor steel and binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or tor steel tying the grills and placing in proper position. Column Base Footing [Farmer Rest Shed-10.80 + Cover Pindi-9.00 +Compound Wall-20.86 = 39.96Cum]

Column up to Plinth [Farmer Rest Shed-1.24 + Cover Pindi-2.34 +Compound Wall-4.35 = 7.93 Cum]

Plinth Beam [Farmer Rest Shed-6.26 + Cover Pindi-9.26 +Compound Wall-10.50 = 22.51Cum]

Column above plinth [Farmer Rest Shed-2.48 + Cover Pindi-3.30 +Compound Wall-6.00 = 9.83 Cum]

Lintel [Farmer Rest Shed-1.54 Cum]

Chajja [Farmer Rest Shed-8.30 Sqm]

Roof Beam [Farmer Rest Shed-3.07 + Cover Pindi Tie beam-3.89 = 6.96 Cum]

Roof Slab [Farmer Rest Shed-8.09 Cum]

RCC Coping [Compound Wall-4.20 Cum]

Cutting, straightening coiled or bent up M.S. Rod or tor steel of SAIL/ TATA / RINL (VIZAG) make including bending, binding, welding and joining if necessary and tying the grills and placing in position as required for R.C.C. Work and for providing fan hooks as required, hoisting, lowering, laying including cost, conveyances, taxes of M.S. Rod or tor steel and binding wires of 18 to 20 gauge and labour required for the work for bending, binding and tying the grills in all floors (Linear measurement will be taken and quantity will be calculated basing on the standard weight of B.I.S. for M.S. Rods or tor steel only. Wastage if any, including weight of binding wire will not be considered for measurement) etc. complete as per specification & direction of Engineer-in-charge. [Farmer Rest Shed-40.74 + Cover Pindi-43.97 + Drying Platform-5.61+Compound Wall-53.64 = 143.96 Qntl.]

Providing 12 mm thick cement plaster with cement mortar (1:6) with screened and washed sharp river sand for mortar and finished smooth to the rough surface of walls after racking out joints including watering and curing, rounding of corners, providing grooves where ever necessary with cost, conveyance, royalties,Addl. charges, DMF&EMF of all materials, cost of all labour, Labour CESS,T&P, and scaffolding as required to complete the work in all respect as per the Direction of the Engineer-in-charge . [Farmer Rest Shed-200.98 + Cover Pindi-24.20 + Drying Platform-17.55+Compound Wall-190.00 =442.73Sqm]

Providing 16 mm thick cement plaster with cement mortar (1:6) with screened and washed sharp river sand for mortar and finished smooth to the rough surface of walls after racking out joints including watering and curing, rounding of corners, providing grooves where ever necessary with cost, conveyance, royalties,Addl. charges, DMF&EMF of all materials, cost of all labour, Labour CESS,T&P, and scaffolding as required to complete the work in all respect as per the Direction of the Engineer-in-charge . [Farmer Rest Shed-67.80 +Compound Wall-195.32 =263.12Sqm]

Providing 6mm. thick cement plaster in cement mortar (1:4) to RCC surfaces finished smooth including closed deep chipping and slurry treatment using good quality screened and washed river sand, including watering and curing, rounding of corners, providing grooves where ever necessary with cost, conveyance, royalties, Addl. charges, DMF&EMF of all materials, cost of all labour, labour CESS,T&P, and scaffolding as required to complete the work in all respect as per the Direction of the Engineer-in-charge . [Farmer Rest Shed-32.95 +Compound Wall-75.00 =107.95Sqm]

Providing ,Supplying fitting and fixing of Kota tiles minimum 16mm thick [ above 0.10 Sqm ] in floors and treads on steps and landing on 20mm thick bed of cement mortar 1:4(1 cement 4 screened and washed river sand) jointed with neat cement mixed with pigment to match the shade of the tiles including rubbing and polishing , curing for required days complete , including cost of Kota tiles , cost , conveyance , royalty,Addl. charges,DMF,EMF of all materials, cost of all labour , labour CESS and T&P required to complete the work in all respect as per specification and direction of the Engineer-in-charge. [Farmer Rest Shed-26.89 Sqm]

Providing ,Supplying fitting and fixing of Kota tiles minimum 16mm thick [ upto 0.10 Sqm ] in Dado skirting and rises of steps on 12mm thick cement plaster 1:3 (1 cement:3 screened and washed river sand) jointed with neat cement mixed with pigment to match the shade of the Kota tiles , including cost of tiles ,curing for required days , cost , conveyance , royalty,Addl. charges,DMF,EMF of all materials, cost of all labour , labour CESS and T&P required to complete the work in all respect as per specification and direction of the Engineer-in-charge. [Farmer Rest Shed-13.17 Sqm]

Providing ,Supplying fitting and fixing of Polished Vitrified floor tiles of premium grade having thickness 8mm to 10mm confirming to IS 15622:2006 (Group-B la) of size 600mm x 600mm, Plain Ivory, in floors and treads on steps and landing on 20mm thick bed of cement mortar 1:4(1 cement : 4 screened and washed river sand ) jointed with neat white cement mixed with pigment to match he shades of the tiles ,curing for required days , including cost of pre cast tiles , cost , conveyance , royalty,Addl. charges,DMF,EMF of all materials, cost of all labour , labour CESS and T&P required to complete the work in all respect as per specification and direction of the Engineer-in-charge. [Farmer Rest Shed-17.28 Sqm]

Providing ,Supplying fitting and fixing of Polished Vitrified tiles of premium grade having thickness 8mm to 10mm confirming to IS 15622:2006 (Group-B la) of size 600mm x 600mm . Plain Ivory, in Dados skirting and rises of steps on 12mm thick cement plaster 1:3 (1 cement :3 screened and washed river sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles , ,curing for required days , including cost of pre cast tiles , cost , conveyance , royalty,Addl. charges,DMF,EMF of all materials, cost of all labour , labour CESS and T&P required to complete the work in all respect as per specification and direction of the Engineer-in-charge. [Farmer Rest Shed-5.04 Sqm]

Supplying, installation of pressed steel door of specific dimension and accessories such as hinges ,door stopper,tower bolt,door handle,door closer,dead lock,consedaled flush bolt,shaft lock,martise lock and vision panel etc. complete as mentioned along with warranty coverrage and after sales service etc inclusive of all cost ,taxes ,GST,cost of delivery charges,fixing ,fitting and any other invidential charges etc.complete.and as per the Direction of the Engineer-in-Charge. [Farmer Rest Shed-2.52 Sqm]

Supplying, installation of pressed steel window of specific dimension and accessories such as hinges ,door stopper,tower bolt,door handle,door closer,dead lock,consedaled flush bolt,shaft lock,martise lock and vision panel etc. complete as mentioned along with warranty coverrage and after sales service etc inclusive of all cost ,taxes ,Gst,cost of delivery charges,fixing ,fitting and any other invidential charges etc.complete. [Farmer Rest Shed-6.44 Sqm]

Supplying, fitting & fixing in all floors of M.S. grills, grill gates, M.S. gates, garage door, collapsible gates with top and bottom rails, steel windows, critical frames for windows, stair case and parapet railing made out of M.S Square bar/ flat including stair case hand railing with 40mm. dia G.I.pipe etc. including painting two coats over a coat of redoxide primer as per approved drawing and design with cost of all materials & labour, labour cess, T&P, sundries etc. complete in all respect as per specification & direction of the Engineer-in-Charge. [Farmer Rest Shed-160.88 +Compound Wall-354.38 =515.26Kg]

Providing and Painting the surface of the walls with one coat of wall primer(water based) of approved quality after cleaning the plastered surface perfectly by watering and brushing including cost , conveyance of all material, brushes, all labour, scaffolding, T&P etc. required to complete the work in all respect as per specification and direction of the engineer-in-charge. (Make: Asian/ Berger/ Dulex/ ICI or equivalent make duly approved by the Engineer-in-Charge) [Farmer Rest Shed-323.49 + Cover Pindi-34.20 + Drying Platform-17.55+Compound W

all-460.32 =835.56Sqm]

Providing & painting exterior surfaces of walls with two coats of antifungal Weather seal coat paint of approved quality and shade from a recognized company to give an even shade, after cleaning the plastered surface perfectly by watering and brushing including cost of scaffolding ,staging and cost ,conveyance of all materials ,all labour, labour CESS and T&P required to complete the work in all respect as per specification and direction of the Engineer-in-charge. (Make: Asian/ Berger/ Dulux/ ICI or equivalent make duly approved by the Engineer-in-Charge) [Farmer Rest Shed-87.58 + Cover Pindi-34.20 + Drying Platform-17.55+Compound Wall-460.32 =599.65Sqm]

Providing and Finishing surfaces of walls & ceiling with cement based wall putty [ water based ] of approved make (JK White/ Birla white or equivalent make duly approved by Engineer-in-Charge) and finishing the surface smooth and even by sand papering to receive painting at all hights including cost of scaffolding ,staging where necessary with cost , conveyance of all the materials ,including cost of all labour, labour CESS and T&P required to complete the work in all respect as per specification and direction of the Engineer-in-charge. [Farmer Rest Shed-235.91Sqm]

Finishing interior surfaces of walls with two coats of Plastic emulsion paint of approved quality and shade from a recognized company to give an even shade including preparation of the surface before applying by sand papering, applying putty wherever necessary, including cost of scaffolding ,staging and cost ,conveyance of all materials ,cost of all labour, labour CESS and T&P required to complete the work in all respect as per specification and direction of the Engineer-in-charge. (Make: Asian/ Berger/ Dulux/ ICI or equivalent make duly approved by Engineer-in-charge) [Farmer Rest Shed-235.91Sqm]

Painting 2 (Two) coats with synthetic enamel paint to iron work of approved quality and shade after sand papering and cleaning the surface including cost, conveyance of all materials, all labour, labour CESS T&P , scaffolding etc. required to complete the work in all respect as per drawing and technical specification and direction of the Engineer-in-Charge. (Make-Asian/ Berger/ Dulux/ ICI or equivalent make duly approved by Engineer-in-charge). [Farmer Rest Shed-3.22 + Cover Pindi-53.74 +Compound Wall-3.94 + Internal Road-84.27 =105.74Sqm]

Providing 2.5cm thick Grading Concrete over roof slab with cement concrete (1:2:2) using 4.7mm size black hard granite crusher broken chips and screened & washed sharp sand for mortar and finished smooth to the rough surface of slab including watering and curing with cost, conveyance, royalties, Addl Charges,DMF&EMF of all materials with cost of all labour, labour cess and T&P required for the work etc. complete in all respect as directed by the Engineer in charge. [Farmer Rest Shed-64.68Sqm]

Waterproofing application:- Providing and application of two component polymer modified flexible cementitious waterproofing coating at a thickness of 1.5 -2.5 mm The membrane should have Elongation equal or more than: 30% Crack Bridging ability : Up to 1 mm Adhesive strength: 1.0 N/mm² @ 28d, Tensile elongation: 60% @ 20°C, Shore A Hardness >85 (between 3 - 7 days) etc. as per direction of E.I.C (For longer span, in terrace panel of 4m*4m should be done by groove cutting, and filling with PU Sealant) (Make-Myk, Fosroc, Sika) [Farmer Rest Shed-64.68Sqm]

Providing and laying cement concrete (1:2:4) using 12mm size black hard granite crusher broken chips and screened and washed sharp river sand of approved quality from approved quarry as per approved design including hoisting, lowering, laying and compacting to proper thickness, watering and curing for the required period, finished smooth , providing grooves or beads where necessary including cost, conveyance, royalty,Addl. charges, DMF&EMF of all materials with labour, labour CESS , and T&P etc. required to complete the work in all respect as per direction of the Engineer-in-Charge. [Cover Pindi-6.41 + Drying Platform-9.35 = 15.76 Cum]

2.5cm thick A.S Flooring with C.C(1:2:4) using 12mm size hard granite crusher broken chips laid to proper slope in two layers bottom layer being 3/4" and top layer being 1/4"with including neat cement punning,Watering and curing for required days including cost, conveyance, royalty,Addl. charges,DMF,EMF of all the materials, cost of all labour , labour CESS and T&P etc. required to complete the work in all respect as per specification and direction of the Engineer-in –charge. [Cover Pindi-78.00 + Drying Platform-93.50 = 171.50 Sqm]

Providing Granular sub-base by providing coarse graded gradind-III materials including watering and compacting including cost, conveyance royalty,Addl. Charges, DMF&EMF of all materials cost of all labour, labour CESS , T&P etc. required to complete thetwork in all respect as per specifications and direction of the Engineer-in-charge.[Internal oad-128.60Cum.]

Supplying and fixing of factory made 80mm thick cement concrete interlocking paver blocks of M-40 grade made by block making machine with strong vibratory compaction of approved make, design, colour and size laid over compacted bed including filling sand in the interstices / joints including cost,conveyance of all materials , all labour,labour CESS and T&P required for the work etc. complete in all respect confirming to IRCSP-63:2018 and as per direction of the Engineer in charge.[Internal Road-514.25Sqm]

Supplying fitting and fixing of builtup GI tubular pipes [Round,Square, Rectangular hollow tubes] for roof purlines and trusses using required dia. of tubes including cutting hoisting welding as necessary, including cost of nuts and bolts, and fixing etc. complete including cost, carriage of all materials , all labour and T&P etc. to complete the work in all respect as per specification and direction of the Engineer-in-Charge.[Cover Pindi-1134.33 Kg]

Supplying fitting and fixing of 0.45mm thick Durashine colour coated sheets (ISI Marked) in roof with fixing of " L" & "j" hooks including cost of nuts and bolts, washers and drilling holes & fixing wind ties and ridges etc. including cost, carriage of all materials(excluding cost of wind ties and ridges), cost of all labour, labour CESS and T&P etc. required to complete the work in all respect as per specification and direction of Engineer-in charge. [Cover Pindi-149.65 Sqm]

Supplying and fixing of pre cast kerb stone of size 600 mm x 300 mm x 150mm of M30 grade of approved make.design colour and size made by block making machine with proper compaction fixed in requied pattern etc.complete in all respect conforming to IS 5758:1984 and as per the direction of the Engineer in charge.[Internal oad-702 Nos.]

Clearing grass and removal of rubbish up to distance of 50m outside the periphery of the area including cost of all labour, labour CESS and T&P. etc. required to complete the work in all respects as per direction of Engineer-in-charges..[Site Development-2500 Sqm]

Supplying of filling good earth in ground and over areas including watering, ramming, consolidating and dressing, labours, tools, taxes etc., all complete as per the specification and direction of Engineer-In-charge.[Site Development-575.19Cum]

E.I. Works Recessed wirring to light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor of ISI

marked Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI with 20 mm dia HMS FRLS PVC conduit ISI marked Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal 6A modular type ( flame retradant type) switch ISI marked Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) and ceiling rose ISI marked of modular type G.I box with metallic cover plate (both side) ( flame retradant type) Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) of suitable size, modular box with 1.5 sq. Mm FRLS PVC insulated single core multistandard copper conductor as earth wire including all accessories and connection as per direction of Engineer -in -Charge. . All the switches & sockets should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials.

-do- light point Group-B

-do- light point Group-C

-do- Fan point Group-B

-do- E. Fan point Group-C

Supplying,fixing of 6A Plug on the separate board with complete fitting by 01 no of 6A switch & socket(modular type)( flame retradant type)) with suitable size modular box & cover( falme retradant type) including supplying of all required accessories of ISI marked as approved as per direction of engg-in-charge..Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) (Maximum 02 nos point in one circuit).All the switches & sockets should be warrantied for a period of 2 years against manufacturing defects against which ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials.

Supplying ,fixing of 6A Plug on the same board in existing switch board with complete fitting by 01 no of 6A switch & socket (modular type)( flame retradant type)) & other required accessories of ISI marked as approved as per direction of Engg. -in -Charge. Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) .(Maximum 02 nos point in one circuit).All the switches & sockets should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials.

Supplying,fixing of 2x6A Plug on the separate board with complete fitting by 01 no of 2 nos 6A switch & socket(modular type) ( flame retradant type) with suitable size modular box & metallic cover plate (both side)( falme retradant type)including supplying of all required accessories of ISI marked as approved as per direction of engg-in-charge. Make-Schneider (Zencelo)/ legrand( ( Myrius) /Panasonic (vision) (For equipement power). (Maximum 02 nos point in one circuit).All the switches & sockets should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials.

Supplying,fixing of 1x16A Plug on the separate board with complete fitting by 01 no of 16A switch & socket(modular type)( flame retradant type)) with suitable size modular box & cover( flame retradant type) including supplying of all required accessories of ISI marked as approved as per direction of engg-in-charge.. Make-Schneider(Zencelo)/legrand( Myrius)/Panasonic (vision) (For equipement power)All the switches & sockets should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials.

S/F of step type Modular electronic Fan Regulator ISI Marked with all connection complete in all respect as per direction of Engineer in charge (Make: legrand Myrius /Schneider(Zencelo)/Panasonic(Vision))

Receass wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal as required as per direction of Engg.-in-Charge. 2 nos single core 1.5 sq. mm copper wire for phase and neutral and 01 no of single core 1.5 sq. mm copper wire for earth continuty conductor. In 20 mm dia non metallic heavy duty conduit (LDB to LSB/LIGHT CKT)(2X1.5+1X1.5)

Receass wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal as required as per direction of Engg.-in-Charge. 2 nos single core 2.5 sq. mm copper wire for phase and neutral and 01 no of single core 1.5 sq. mm copper wire for earth continuty conductor in 20 mm dia non metallic heavy duty conduit.(BDB to LSB/LIGHT CKT/5A PLUG/UPS POINT ) (2X2.5+1X1.5)

Receass wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal as required as per direction of Engg.-in-Charge. 2 nos single core 4 sq. mm copper wire for phase and neutral and 01 no of single core 1.5 sq. mm copper wire for earth continuty conductor in 20 mm dia non metallic heavy duty conduit .(PDB to PSB/ POWER POINT/AC POINT) (2X4+1X1.5)

Receass wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal as required as per direction of Engg.-in-Charge. 2 nos single core 6 sq. mm copper wire for phase and neutral and 01 no of single core 2.5 sq. mm copper wire for earth continuty conductor in 25 mm dia non metallic heavy duty conduit .(LFDB TO LBDB/UBDB) (2X6+1X2.5)

FITTING & FIXTURE Supplying, installation, testing and commssioning of 1200 mm sweep white/milky colour BLDC ceiling fan with aluminium blades having wattage not more than 28W and air delivery ≥215m3/min Make-Crompton Energion Groove /Havells Efficiencia Neo/Usha Technix ) including wiring the down rod of standard length (upto 30 cm) with 1.5 sq mm PVC insulated, copper conductor, single core cable etc. as required as per direction of Engg.-in-Charge,Replacement Warranty will be 4 years.. .( fan Regulator compatible)

SITC of energy efficient LED tube light fittings with decorative alluminium batten and LED tube light having power rating not more than 20 watt and lumen output not less than 2200 lumen complete with electronic driver and all other accessories with diffuser having 5 years warranty

i/c connection etc as required as per direction of Engg.-in-Charge. (Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj). The luminaire should be Replacement Warranty will be 2 years .

Supplying and fixing extra conduit down rod of 20 cm length G.I. pipe 15 mm dia, heavy gauge including painting etc. as requiredas required as per direction of Engg.-in-Charge . (Note : More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)of ISI mark as approved.

CABLE TRAY & RACE WAY MCB,RCCB,BDB Supplying and fixing of following mentioned way, three pole/single pole and neutral, sheet steel,double door MCB distribution board, 415 volts/240 volts shall be as per IEC 61439-3,integrated door earthing system offering additional safety to the user,High quality polyurethane Gasket,the box and cover shall be fabricated to withstand IK09,IP 43 the DB should be properly pre-treated with 7 tank process and duly powder coated, phosphatized with powder coated finish, on surface/recess, complete with terminal blocks,with suitable size FR PVC insulated copper conducter up to terminal blocks, tinned copper busbar, neutral busbar, earth bar, din bar. Make-LEGRAND-Ekinox3 DB/ Siemens-Betaguard/ Schneider- Acti 9 as per direction of Engg.-in-Charge. The Distribution boards should be Replacement Warranty will be 3 years. 8 way SPNDB (GLAZED door)

Supplying and fixing 6-32 Amps rating, C series,10KA breaking capacity,SP, 230 volts, MCB . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9 in the existing MCB DB complete with connections, testing and commissioning etc. as required as per direction of Engg.-in-Charge. .. The MCB should be Replacement Warranty will be 3 years..

Supplying and fixing 6-32 amps rating, 240 volts, C series,10KA breaking capacity, Double poles MCB of Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9 in the existing MCB DB complete with connections as per direction of Engg.-in-Charge. The MCB should be Replacement Warranty will be 3 years.

Supplying and fixing 25 Amps 2P 240 volts RCCB 30 mA Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9 in the existing MCB DB in the existing MCB DB complete with connections as per direction of Engg.-in-Charge..The MCB should be Replacement Warranty will be 3 years.

PANEL S/I/T&Commissioning of LT indoor/outdoor floor/wall mounted cubical type electrical main panel (for both light and power circuit) made out by 2mm CRCA steel sheet duly derusted & painted by simens grey powder cote paint is designed as G.A drawing. (FOR ALL MAIN CONNECTED LOAD) PUMP)as per direction of Engg.-in-Charge. Warrentee period of replacement of panel & accessories must be 3 years & compelete test certificate must be submitted along with panel board including component list.Type 2 SPD 40ka shall be installed in the incomer. 20X10MM Separate Aluminium Earth bus bar should be installed. In commer 1- 01 no 63A 4P MCB,10KA,C SERIES Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9 Busbar- 04 numbers of 100Amps 25*3mm copper bus bar Electrolytic copper busbar duly sleeved by color coded PVC sleeve & supported by suitable size DMC insulator. Out going- 02 nos 40A 4P MCB 10kA,C . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9 Out going- 05 nos 32A 2P MCB 10kA,C . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9 Instrument- (i) 03 numbers phase indicating lamp with toggle switch & HRC fuse. (ii) 01 set of 0-100Amps MFM with CTS.(DIGITAL)(Sicure/L&T,CT-KAPPA or equievalant make & model) EXTERNAL ILLUMINATION

S/F of Street light- 60W,120 lm/w efficacy , new generation energy saving & environmental friendly long life versatile pressure die-cast alluminium IP66 roadway luminaire with high power LED as light source with acrylic cover(Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj) (5Years Warranty)

Supply of 7 mtr long single arm hot dip Galvanized Octagonal pole manufactured from HT steel as per BS EN 10025/IS 2062 having minimum yield strength of 350 N/ SQMM having top dia of 70 MM A/F and bottom dia of 130 MM A/F of 3 mm thick or more , base plate as per IS 2062 complete with 4 nos. En 8 grade foundation bolts to withstand basic wind speed of 180 KM/HR wind speed (As per structural calculation of pole manufacturer )or more (Make of poles: Utkarsh/Bajaj/RR Ispat as per direction of Engg. in Charge.

Supply and fixing of 9mtr high Octagonal GI pu painted pole shall be designed to withstand the maximum wind speed as per IS 875. The top loading i.e. area and the weight of fixtures are to be considered to calculate maximum deflection of the pole and the same shall meet the requirement of BSEN 40-3-3:2003. Octagonal Poles made from HT Steel Conforming to grade S355 & having thicknessof 3mm.Top dia 70mm & Bottom dia 175mm single sharp welding with base plate dimension 275x275x16 mm & Base Plate must be Fe 410 conforming to IS 2062, foundation bolts must EN 8 grade & bolts size must be 4X24mm dia,PCD 275mm,Bolt length 750mm long.The door opening of the pole should be reinforced,water proofed & with locking arrangement & arrangement of in build junction box with 2nos 6Amp MCB (mcbs make should be Siemens/schneider ) & terminal box with provision for connection of earth & nutral on 5mm thick fiber plate which will be kept in side the pole for termination of cable & wire,The pole shaft shall have octagonal cross section and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding. The welding of pole shaft shall be done by Submerged Arc Welding (SAW) process The poles shall be hot dip galvanized in single dipping as per BS EN ISO 1461 standards with avarage coating thickness of 70 Micron. Pole should have the clamp holding arrangement at 5mtrs height for fixing decorative single arm design bracket. ( Make- Bajaj/LYSAGHT/ VALMONT/Utkarsh/RR Ispat . Design is specially as per drawing as per direction of Engineer in charge.(Ring type round arm having provision for 4 nos. LED Floodlight)

Foundation & erection of 9 mtr street lighting pole along with all materials & labour M20 concrete, as per direction of engineer in charge as per approved design

Supplying, Erection, Fixing, connection & testing of 40W LED GATE Light of Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj) maintenance free having 5 years warranty G.I P ipe with braket including MCB box & including with foundation as per the Drawing for inspection as required & as per direction of Engg.-in-Charge.

Supplying, Erection, Fixing, connection & testing of 100W FLOOD Light of Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj maintenance free having 5 years warranty wit including MCB,stainless steel braket along with driver & including with foundation as per the Drawing for inspection as required & as per direction of Engg.-in-Charge.

S/IT/C of materials and installation of GI earth plate 600mmx600mmx6mm thick ISI marked with G. I. nut bolts & washers including cost of burnt wood charcoal, salt, foreign soil, water pouring arrangements, brick masonary enclosure on top with removable RCC cover complete with labour for excavation of pit in all kinds of soil & rock as required and as per direction of Engineer-in-charge.

Providing and fixing swg 6 GI wire on surface or in recess for loop earthing as required as per direction of Engg.-in-Charge.

CABLING Supplying of one number PVC insulated armoured and PVC sheathed XLPE property AL. conductor power cable of 1.1 KV grade Make- Finolex/Polycab/HAVELLS/RR KABLE/KEI/Gloster of following size cables as per direction of Engg.-in-Charge. 4core x 6 sq mm

Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size not exceeding 25 SQ. MM direct in ground in the trench in one horizental formation including excavation ,sand coushing protection covering and refilling the trench etc as required as per direction of Engg.-in -charge.

Supplying,laying of 3cx2.5 sq.mm copper flexible cable with insulated cover of reputed make,ISI marked with all other concerned materials as per dire

ction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials

Providing,fixing and laying of fallowing dia PN10 HDPE pipe (medium class) in ground complete with fitting incl. trenching(75 mm depth)and refilling as per direction of Engg.-in-Charge. 32mm

P.H Work Supplying all materials, labour, T&P and providing and fixing to wall or ceiling and floor pvc pipes conforming to ASTM-D-1785/89 (Sch-80) and pipe fittings of the following nominal bore with clamps including making good the wall, ceiling and floor all complete as per specification and direction of the Engineer in charge.(Supreme/Ashirvad/Oriplast) Ground Floor 20mm Dia CPVC Pipe

25mm Dia CPVC pipe

32 mm dia UPVC ASTM (Sch-80) pipe

40mm dia UPVC ASTM (Sch-80) pipe-First floor

Supplying all materials, labour, T&P and cutting holes through existing brick work including making good the damages in cement mortar (1:4) for taking GI pipes and fittings/ PVC pipes and fittings etc all complete as per PH specification and direction of the Engineer in charge.250mm Thick Wall Ground Floor

Supplying all materials, labour, T&P and cutting hole in R.C.C floors, roofs, etc upto 19 cm thick for passing GI pipes / PVC pipes and fittings etc and repairing the holes after insertion of pipes etc with cement concrete (1:2:4) including finishing complete so as to make it leak proof as per direction of the Engineer in charge. in ground Floor

Supplying all materials, labour, T&P and cutting grooves in pucca floors and walls for taking GI/ PVC pipes and making good the damages as per the direction of the Engineer in charge. Ground Floor

Supplying all materials, labour T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all joiniting materials complete as per specification and direction of the Engineer in charge. 15mm dia long body Bib Cock cock (Jaquar)-CON-CHR-107KN

20mm dia CP concealed stop cock(Jaquar)CON-CHR-087KN

15mm dia CP angle stop cock (FLR-ACR-5053N)

15mm dia CP Pillar cock (Jaquar)CON-CHR-021KN

15mm dia CP Health faucet.ALD-CHR-579

15mm dia Two way Bib Cock (Jaquar)-CON-CHR-041KN

Shower Arm (SHA-CHR-477)

Over head shower 100mm dia round (OHS-CHR-1999)

25mm dia brass or gun metal full way valve(shakti make)

40mm dia brass or gun metal full way valve(shakti make)

15mm dia CP Flange

15mm dia CP Extention Nipple

125mm CP grating

Supplying all materials,labour,T&P and fixing Rotational moulded polyethylene cylindrical vertical water storage tanks conforming to IS : 12701--1996 including cutting holes through the tank and fixing mild steel tubes and fittings and providing extra sockets and jam nuts, fixing ball valve etc, including hoisting upto a height of 5 metres above ground level and placing the tank to the required position and providing 1st class Fly ash brickwork in cement mortar (1:6) of 0.46m height in staging and in circular protection wall to support the tank, 12mm thick cement plaster (1:6) over brickwork, R.C.C slab of size 1.60mx1.60m and 0.10m thick, R.C.C beam of 0.25mx0.30m and 2.60m average length in cement concrete(1:2:4) using 12mm size h.g chips including centering and shuttering, watering, curing, conveyance of all materials to worksite etc all complete as per specification and direction of the Engineer in charge. Fixing 2000 Ltr Roto-moulded water storage tank (3 layers) on the roof of 1st floor

Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No. 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer’s specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer in charge(Supreme/Ashirvad/Oriplast) 110mm dia U-PVC SWR pipe

75 mm dia UPVC SWR Pipe (supreme/ashirvad)

110mm U-PVC door tee

110mm U-PVC Plain tee

110mm U-PVC door bend

110mm U-PVC plain bend

110mm dia U-PVC 'P' trap

110mm dia U-PVC Plain Shoe Bend

110mm dia U-PVC offset with out ear

110mm dia U-PVC cowl

75 mm dia UPVC plain bend

75 mm dia UPVC plain Tee

Supplying all materials, labour, T&P and fixing the following vitreous china Wash Down Water Closet (European type W.C pan) with integral ‘P’or ‘S’ trap to the floor with wooden plug and chromium plated pedestal screws including jointing the trap with soil pipe in cement mortar (1:1), fixing plastic seat and cover for wash down water closet with chromium plated brass hinges and rubber buffers including polishing etc all complete as per specification and direction of the Engineer in charge. European water closet with ‘S’ trap plain (Parryware / Nycer make)

Supplying all materials , labour, T&P and fixing Vitreous china water closet ,squatting pan ( Indian type W.C. pan / Orissa pattern squatting pan ) duly embedded in cement concrete 1:5:10 using hard granite metal 4cm nominal size including fixing a pair of vitreous china 250mmx130mmx30mm foot rest, fixing 100mm dia hci 'P' or 'S' trap for water closet squatting pan including jointing the trap with pan in cement mortar (1:1), cutting the floor and mending good the damages etc. all complete as per P.H. specification and direction of Engineer-in-charge. 580mmx440mm size Orissa pan (Parryware/Hinware)

Supplying all materials, labour, T&P and fitting and fixing 10 litres capacity low level flushing cistern with a pair of cast iron or M.S brackets complete with fittings such as siphonic arrangements 15mm nominal size brass/pvc ball valve with polythene float CP brass handle, unions and couplings for connection with inlet, outlet and overflow pipes,32mm dia CP flush bend,15mm dia pvc inlet connection pipe including cutting holes and making good the same and connecting the flush bend with cistern and closet and connecting the inlet pipe with supply main etc all complete as per specification and direction of the Engineer in charge. 10 litres capac

ity pvc low level cistern with 32mm dia CP long flush bend Slimline white (Parryware/Hinware/Somany/Cera/Kerovit)

Supplying all materials, labour, T&P and fixing bowl pattern urinal conforming to IS:771-part-3-1985 of the following sizes including connecting the urinal with 32mm dia pvc waste pipe 910mm long by means of white lead mixed with chopped hemp, fixing 32mm dia CP dome waste, 15mm dia CP spreader including cutting holes in walls and making good the damages with supply of wooden plugs, screws and cement etc all complete as per specification and direction of the Engineer in charge. Half stall urinal (Jaquar/Parryware / Hindware make). URS-WHT-13253N Urinal (Back Inlet)

15mm dia urinal spreader

32mm dia C.P. dome waste

Supplying all materials , labour, T&P and fixing Vitreous china water closet ,squatting pan ( Indian type W.C. pan / Orissa pattern squatting pan ) duly embedded in cement concrete 1:5:10 using hard granite metal 4cm nominal size including fixing a pair of vitreous china 250mmx130mmx30mm foot rest, fixing 100mm dia hci 'P' or 'S' trap for water closet squatting pan including jointing the trap with pan in cement mortar (1:1), cutting the floor and mending good the damages etc. all complete as per P.H. specification and direction of Engineer-in-charge. squatting URINAL pan(Parryware/Hinware/Somany/Cera/Kerovit)

Supplying all materials, labour, T&P and fixing wash basins with hole for pillar taps with cast iron or M S brackets painted white including cutting holes in walls and making good the damages with supply of wooden plugs, screws and cement etc, fixing pedestal for wash basin recessed at the back for the reception of pipes and fittings, fixing PVC waste pipe of 32mm nominal diameter for wash basin including brass check nut complete, fixing pillar taps capstan head screw down high pressure lettered ‘Hot’ and ‘Cold’ with long screws, shanks and back nuts of 15mm dia nominal bore, fixing 15mm dia PVC inlet connection pipe and making connection with pillar cocks and supply mains for wash basin, fixing 32mm dia CP brass waste, etc all complete as per specification and direction of the Engineer in charge. 550mmx440 mm size wash hand basin With porcelain pedestal(Parryware/Hinware/Somany/Cera/Kerovit)

Supplying all materials,labour, T&P and fixing standard sized CP towel rail complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge 25mmx600mm long CP towel rail

CP Towel ring

Supplying all materials ,labour ,T&P and fixing CP Soap Holder complete with CP brass brackets fixed to wooden plugs with chromium plated brass screws etc.all complete as per specification and direction of Engineer-in-charge. CP soap holder

Supplying all materials, labour, T&P and fixing standard sized glass-shelf with CP brass brackets and guard rails complete fixed to woden plugs with CP screws as per specification and direction of the Engineer in charge.600mmx125mm glass shelf with CP/NP guard rails

Supplying all materials, labour, T&P and fixing mirror of superior glass mounted minimum 5m thick on 6mm thick A.C sheet or plywood sheet and fixed to wooden plugs with CP screws and washers complete as per specification and direction of the Engineer in charge. Mirror(Bevellededge) 600mmx450mmx200mm

Supplying all materials, labour, T&P and filling in foundation and plinth with sand well watered and rammed including conveyance of all materials to worksite, payment of royalty, taxes etcall complete as per direction of the Engineer in charge. Ground Floor;-

Supplying all materials, labour, T&P and providing cement concrete ( 1:3:6 ) with 4cm size crusher broken hard granite metal including watering, curing, cost of all materials,conveyance of all materials to work site with payment of royalty, all taxes etc all complete as per P.W.D specification and direction of Engineer-in-charge Ground Floor;-

Supplying all materials, labour, T&P and providing cement concrete (1:2:4) with 12mm size hard broken granite chips including watering, curing, conveyance of all materials to worksite, payment of royality, taxes etc all complete as aper specification and direction of the E.I.C. Ground Floor;-

Supplying all materials, labour, T&P and providing 12mm thick cement plaster (1:4) on brickwork including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge Ground floor .

Supplying all materials, labour, T&P and providing ceramic tiles in floors, treads and landing on 25mm thick bed of cement mortar 1:1 (1 cement:1 sand) joined with neat cement slurry mixed with pigment to match the shades of the tiles including rubbing and polishing complete as per direction of the Engineer in charge. Kajaria / Somany / Johnson to be pre-approved 300 x 300mm of size In Ground Floor

Supplying all materials, labour, T&P and fixing porcelain glazed tiles in dados skirting on 12mm thick cement plaster (1:3) jointed with neat cement slurry mixed with pigments to match the shades of the tiles including rubbing and polishing complete as per direction of the Engineer in charge. Kajaria / Somany 30cm x 45 cm size of Ground Floor;-

Factory made Solid WPC door frame of size 90mmx45mm fabricated .The door frame consist of four segments which are provided with plug-in-socket arrangement in-situ in the mould. The segments are plugged in and are joined together by means of screw. The WPC frame shall be provided with The material and process for manufacturing the door frames shall conform to Relavent I.S.specification. The finish of door frame will be plain colour white/ Ivory/ Beige/ Light grey/ Golden brown/Mahogany/ Teak wood/sand stone/Champagne/Pastel blue or any other colour using high quality pigments complete in all respect as per specification and direction of the Engineer in charge (Rajshri plastiwood/Alstone/Aramstrong or equivalent as per direction of Engineer-in-charge)

Factory made single leaf Solid WPC (Wood polymer) composite door shutter of 25mm thickcompacted with wood grain finish structural foam panel of 29mm thickness and a density of 650kg/cu.mtr shall be used as core material for fitting the metal fittings such as tower bolts, aldrops, handles etc shall be provided. A structural adhesive compatible with (EPS) foam shall be used for bending the core material, The material and process for manufacturing the door shutters shall conform to RV-TIFAC composites Design Centre's standards and specifications and the door shutters Conforming to relevant I.S.specification. The finish of door shutter will be plain colour brown/ Ivory/ Beige/ Light grey/ Mahogany/ Teak wood or any other colour using high quality pigments. Three heavy whight mild steel butt hinges type-I(ISI marked) size 100mm are to be fitted on one side of shutter. (Rajshri plastiwood/Alstone/Aramstrong or equivalent as per direction of Engineer-in-charge)

Supplying all materials, labour, T&P and constructing gully trap chamber of the following inside size with 8cm thick R.C.C precast cover slab in cement concrete (1:2:4) mix using 12mm size h.g chips, foundation concr

ete (1:4:8) using 40mm size hard granite metal on bed and around trap, KB brickwork in cement mortar (1:6) in F&P and inside 12mm thick cement plastering (1:3) finished with a floating coat of neat cement including fixing 100mmx100mm size HCI gully trap,150mmx150mm size CI grating etc all complete as per approved drawing, specification and direction of the Engineer in charge. Inside size 250mmx250mm

Supplying all materials, labour, T&P and constructing inspection chamber of the following size with cement concrete(1:3:6) using 40mm size hard granite metal on bed, 1st class fly ash brickwork in cement mortar(1:6), moulding and shaping the channel inside and benching with cement concrete (1:2:4) using 12mm size h.g chips, 12mmthick cement plaster (1:3) with punning to inside, cement flush pointing (1:3) to outside, RCC cover slab in (1:1.5:3) using 12mm size h.g chips with RCPC man hole cover, earthwork in excavation in all kinds of soil and refilling the cavity around the chamber including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per approved specification and direction of the Engineer in charge. Inside size 760mmx760mmx460mm

Supplying all materials, labour, T&P and constructing man hole chamber of the following size with cement concrete(1:3:6) using 40mm size hard granite metal on bed, fly ash brickwork in cement mortar(1:6), moulding and shaping the channel inside and benching with cement concrete (1:2:4) using 12mm size h.g chips,12mmthick cement plaster (1:3) with punning to inside, cement flush pointing (1:3) to outside, R.C.C cover slab in (1:1.5:3) using 12mm size h.g chips with RCPC man hole cover, earthwork in excavation in all kinds of soil and refilling the cavity around the chamber including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per approved specification and direction of the Engineer in charge. Inside size 910mmx910mmx910mm

Supplying all materials, labour, T&P and constructing soakway pit of the following size with dry brick walling from bottom upto invert of inlet pipe and fly ash brickwork in cement mortar (1:6) for the remaining height at top, cement concrete (1:4:8) using 40mm size hg chips on bed, 12mm thick cement plaster (1:4) inside and outside over masonry brickwork, gravel backing in the rear of well steining, RCC cover slab in cement concrete (1:2:4) using 12mm size hg chips fitted with iron lifting handles including earthwork in open well excavation in all kinds of soil and refilling of cavity around the pit & painting the iron works, watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per approved specification and direction of the Engineer in charge. 1.40m dia x 2.00m deep soakway pit

Supplying all materials, labour, T&P and laying in trenches (to level or slope) unplasticized PVC pipes conforming to IS: 4985/2000 of the following outside dia for class–3(0.60mpa) including jointing with supply of approved solvent cement by non-heat application method/as per manufacturer’s specification, providing and laying in trench cement concrete (1:4:8) with 40mm size hard granite metal in the Type C-1 standard bedding surrounding or encasing including concrete for bedding and curing etc all complete as per PH specification and direction of the Engineer in charge. 110mm dia U-PVC Alround Concrete

160mm dia U-PVC Alround Concrete Construction 1 nos 20 users RCC Septic tank

Earth work in excavation of foundation in all kinds of soil within 50m initial lead and 1.5m initial lift including rough dressing & breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.3m in depth and as per direction of the Engineer-in-Charge.

- do - with addl. Depth of 1.5 m

Excavation of foundation in laterite rock or any hard rock (other than granite or disintegrated rock) removed by chiselling including dressing and levelling the bed not exceeding 1.50 mtr. in depth and depositing the soil within initial lead of 50 mtr. and as per specification approved by the Department.

Supplying all materials,labour ,T&P and filling in foundation and plinth with sand well watered and rammed including cost, conveyance of all materials to work site ,payment of royalty,taxes etc. all complete as per direction of the Engineer-in -charge In ground floor

Supplying all materials, labour, T&P and providing cement concrete ( 1:2:4 ) with 4cm size crusher broken hard granite metal including watering, curing, cost of all materials,conveyance of all materials to work site with payment of royalty, all taxes etc all complete as per P.W.D specification and direction of Engineer-in-charge. In ground floor

Supplying all materials, labour, T&P and providing cement concrete (1:1:5:3) with 12mm size hard broken granite chips for R.C.C works including hoisting, laying, watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and providing rigid and smooth centering and shuttering for R.C.C works including false work and dismantling them after casting including conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge Roof Slab

For RCC wall

Supplying all materials, labour, T&P and providing M.S reinforcement for R.C.C work including cutting, bending, binding, and tying the grills and placing in position including cost of binding wire 18 to 20 gauge, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

Supplying all materials,labour,T&P and providing 6mm CP (1:4) with cement punning on brick work including watering,curing,cost of all materials, conveyance of all materials to worksite,payment of royalty,all taxes etc.all complete as per PWD specification and direction of the Engineer-in-charge.

Supplying all materials, labour, T&P and making MS step iron in 20mm diameter MS steel bars and fixing into walls of man hole/septic tank duly embedded in cement concrete (1:3:6) complete as per specification and direction of the Engineer in charge.

Supplying all materials, labour, T&P and fitting and fixing S.W.Tee of size 160mx160mx160m as per P.H.D.specification and direction of the E.I.C.

Supplying all materials, labour, T&P and constructing vent base as per P.H.D specification etc all complete.

Supplying all materials, labour, T&P and fitting and fixing UPVC SWR soil waste ventilating pipes and fittings to walls with nails, bobbins and wooden plugs or laying in trenches including earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the engineer in charge. 110mm diameter U-PVC SWR pipe

110mm dia U-PVC Plain shoe bend

110mm dia U-PVC Cowl

Filling in foundation and plinth with excavated materials, moorum including watering and ramming as directed by the Engineer in charge

Sinking of 150mmx125mm dia large Tube well Labour for drilling a perfectly vertical bore hole of specified dia for a specified depth below ground level through consolidated and unconsolidated rock with down the hole hammer drilling rig or combination rig as required to suit the site condition as per the direction of the Engineer in charge including use of own rig with its accessories,

tools and plant and consumables etc for lowering of 200mm/150mm dia G.I/P.V.C/M.S casing pipes for housing fitted with socket and with or without well screen as per the necessity for soft, medium, hard and boulder formation(G.I/P.V.C/M.S casing pipes if required to prevent collapse of overburden is to be provided by the contractor including lowering and withdrawing after completion of the tube well), 200mm dia to 400mm dia in overburden portion including packing of gravel supplied by the contractor for 400mm dia bore. Labour for Drilling of 150 mm dia bore 0mtr to 30mtr

Labour forDrilling of 125mm dia bore 31mtr to 45mtr

Labour for Drilling of 125 mm dia bore 46mtr to 120mtr

Lowering the following size of G.I/P.V.C/M.S housing pipes with or without slotted pipes as per the necessity from ground level up to 45.00m depth and fitted and fixed up in perfectly vertical position including cutting and threading of pipes and slotted pipes and supplying and fixing all jointing materials, tools and plant etc all complete and keeping the top of casing pipe threaded including plugging tube wells to prevent entry of foreign materials. Lowering of 125 mm dia GI/P.V.C/MS casing pipes 0 mtr to 30 mtrs

Lowering of 125mm dia GI/P.V.C/MS casing pipes 31 mtr to 45 mtrs

125 mm dia ASTM-D-1785/89 P.V.C schedule-80 pipe

Cleaning and developing the tube well with supply of compressor worked till clear and adequate discharge is obtained from the tube well including supply and use of all necessary equipment and labour as per direction of the Engineer in charge By DTH

Supplying all materials and labour,tools and plant and providing sanitary sealing by cement concrete grouting of annular space around GI/PVC/MS housing pipe upto 5 mtrs below ground level(as per drawing)to plug the bore hole excluding cost of cement all complete as per direction of the Engineer in charge. Minimum one metre of casing pipe to be inserted in the bore into the rock the bottom to ensure sanitary sealing(excluding cost of cement which willbe supplied by the Department). Submerssible Pump Set 1 H.P three phase 3 stage head range 30 to 54 metres, discharge 155 to 6110 L.M.P with outlet dia of 32 mm.

DOL control panel

2.50 sqmm cable

32mm dia steel short piece