C/O Boundary wall of 01 park in Pocket 2B Sector 18, YEIDA. WC-H

Earth work in ordinary soil in all of foundation trenches including dressing of the side and ramming of bottom lifts upto 1.5m including getting out the excavated soil and disposal of surplus excavatd soil as directed within a lead of 50 m AR/GNIDA(AOR-Sr. no 6 item code. 2.8.1)

Providing and laying in position cement concrete with 4cm gauge stone ballast, coarse sand and cement in proportion 8:4:1 , including supply of all materials, labour, Tools & plant extra for proper completion of the work. (SOR item no 281/p-17)

M-150 brick work in 1:4 1 cement and 4 coarse sand of 2.20 FM mortar in foundation and plinth including supply of all materials, labour and T&P etc. required proper completion of the work. (SOR item no305a/ p-19)

M-150 brick work in 1:4 1 cement and 4 coarse sand of 2.20 FM mortar in superstructure for wall of one brick thick. including supply of all materials, labour and T&P etc. required proper completion of the work. (SOR item no305a/ p-19)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) (AOR sr. no 20/Item code no 5.1.2)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - above plinth level and up to 5th floor level :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) (AOR sr. no 20/Item code no 5.1.2)

Steel reinforcement for RCC Work including straightening, cutting, bending,placing in position and binding all complete up to plinth level miled steel and medium tensile steel bars. (AOR-Sr. no 30 item code. 5.22.1)

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete (AOR Sr. no 135 item code no 5.9.1

Columns , Pillars , Piers, Abutments, Posts and Struts. (AOR-Sr. no 26 item code. 5.9.6)

Linter, beams, plinth beams, griders,bressumers and canti levers (AOR-Sr. no 23 item code. 5.9.5)

Edges of slabs and breaks floors and walls- under 20cm wide. (AOR-Sr. no 27 item code. 5.9.16.1)

12mm cement plaster of mix 1:6 (1Cement: 6 Coars sand) (AOR-Sr. no 56 item code. 13.4.2)

15mm cement plaster on rough side of single or half brick wall of mix 1:6 (1Cement: 6 Coars sand) (AOR-Sr. no 57item code. 13.5.2)

Finishing walls with water proffing cement paint of approved make and quality with three coats and give an even shade including supply of material laour, tools and plants etc, required for proper completion of per work. (SOR item no 660+661/p-23)

Cutting groove in plaster 1cm wide and 1cm deep by using special tools including supply of all tools and plants etc complete. (SOR sr. 21.18/ page 27)

Providing and laying in position cement concrete of specified grade excluding grade excluding the cost of centering and shuttering all work up to plinth level 1:2:4 coars sand 20mm stone aggregate (Sor based DAR 18/4.1.13) for vicate floor)

Supply and fixing of RCC Grill work jali of approved lpattern and make at site of work in cement concrete|Consisting of cement, approved coarse sand and 6mm nominal size stone grit in the proportion of 1:2:4 and reinforced with 6 mm dia M.S wire/bar including |cutting and finishing with 1:3 cement and fine sand of1.25 finess modulus mortar including supply of all |materials. labour, tools and plants etc, required forproper completion of the work but excluding plaster on jambs, still and soffit of the opening 1. 5cm thick (Sor Sr. no 21.17 /page 27)

Steel work welded in built up sections/ framed workincluding cutting hoisting fixing in position and applying a priming coat of approved steel primer using structural steel etc as required. graatings, frames, guard bar, ladder, railings, brackets ,gates and similar works . (AOR-Sr. no 44 item code. 10.25.2)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.Two or more coats on new work (AOR-Sr. no 65 item code. 13.61.1)

Letter wrtting on vertical RCC slab with cement Mortar of mix 1:3 (1 cement: 3 fine sand) including cutting of stensils by rotur/ laser cutting method on 8mm thick sun board in prescribed formate/font and size as direction of Enginner-in-charge/ DD(H)

Supply of JCB on hire basis…

Please Enable Macros to View BoQ information