Special repair of Naib Tehsildar Residence at Assandh

Amount

Stripping and stacking slates or tiles of a roof (HSR 8.10)

Removing door and windows (wood and steel) with chowkats by making recesses in walls when the walls is not to be dismantlled (HSR 8.18) a) Door

b) Window

Dismantling cement conglomerate / terrazzo floors 25 mm to 50 mm thick without concrete base (HSR 8.26)

Scraping (HSR 8.32) (a)white wash and colour wash

(c)cement plaster

Dismantling white or coloured glazed tiles (to be carefully removed) (HSR 8.38)

Providing and Laying 60mm thick interlocking paver blocks of all shapes and colours in design mix cemennt M-35 over a bed of 25mm thick fine sand complete in all respect. (HSR 10.158)

Tile terracing with one layer of tiles, 22.86 cm X 11.43 cm X 3.81 cm laid dry over a layer of mud mortar including grouting with cement sand mortar 1: 3 and top surface to be left clean.(HSR 13.14)

Cement concrete 1:2:4 gola 10cm X 10cm quadrant along junction of roof with parapet wall finished smooth, where specially specified.(HSR 13.64)

Providing & Fixing PVC Rainwater Pipe 6 kg. pressure of ISI mark in cement mortar during masonry work. (Note:- Reputed make PVC Pipe such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. [HSR 13.89]. (a) 100 mm dia PVC pipe 6 kg. pressure. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing and fixing PVC Bend ISI Mark. (Note:- Reputed make PVC Bend such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. [HSR 13.90]. (a) 100 mm dia PVC Bend. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Base course of floors consisting of 100 mm thick cement concrete 1:8:16 and 100 mm sand or stone filling.(HSR 14.1)

Conglomerate floor 40 mm thick cement concrete topping 1:2:4 (HSR 14.9)

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, RAK & JOHNSON. (HSR 14.89)

Providing & fixing ceramic tiles/anti skid tiles of size 400mm x 400mm or above size of approved make in flooring, laid in any pattern as specified over base of 20 mm thickcement coarse sandmortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note : Tile shall be of premium quality (first quality) of reputed manufacturer like:- RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL, SIMPOLO shall be used as approved by Engineer-in-charge. (HSR 14.91).

Providing & Fixing Ist quality Ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manu-facturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (b) Size of ceramic Glazed tiles 300 x 450 mm of reputed manufacturer like:- RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL, SIMPOLO shall be used as approved by Engineer-in-charge. [HSR 14.92(b)]. Size of ceramic Glazed tiles 300 x 450 mm

12 mm thick cement plaster 1 : 4 on walls ( HSR 15.5 )

15 mm thick cement plaster 1:4 on the rough side of single or half brick wall(HSR 15.10)

Preparation of ply wood surface for painting inlcuding sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete. Painting on wooden surfaces etc. (HSR 16.1)

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.2).

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.3).

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surface. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.25).

Painting two coats with ready mixed emulsion paint in all shades for interior use on bricks, plaster, cement, fibre board etc. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.27)

Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). [HSR 16.79 (b)].

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (Note:- reputed make Putty such as J.K./ Birla shall be used as approved by Engineer-in-charge). (HSR 16.81).

Providing and fixing 150 mm floor brass door stoppers, with rubber cushion, screws, etc., to suit shutter thickness complete. [HSR 17.75]

Providing and fixing sliding bolt with nuts and screws, etc., complete (b) Aluminium [HSR 17.82(b)]

Factory manufactured panelled door or glazed windows shutters of commercial hard wood such as Hollock, Champ, Chikrassy & Chaplash etc. (non coniferous timber other then teak, confirming to I.S. specification No. 1003, Kiln seasoned) with 100mm wide vertical styles, 150mm wide lock rail 200 mm wide bottom rail, and 100mm wide other rails, with panels of 15mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screws, chocks/cleats, stops nails etc. complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position). (b) 35 mm thick. [HSR 17.90 (b) - Note 1 under 17.18].

Factory manufactured wire gauze door and window shutters of commercial hard wood, such as hollocks, champ, chikrassy and chaplash, etc., (non-coniferous timber other than teak, conforming to I.S. specification No. 1003, kiln seasoned), with 100 mm wide vetical styles, 150 mm wide lock rail, 200 mm wide bottom rail and wire gauze of 140G or 120G designation including cost of iron hinges, screws, chocks/cleats,stops, nails etc., complete fixed in position (execluding the cost of any fittings, other than specified above but including labour for fixing the same in position) [HSR 17.92 (-)Note (i) under item No. 17.18] ii) 35 mm thick.

Wrought iron and mild steel ladders, framed grills, grattings etc., with ends of bars rivetted or forged framed window guards, barred iron doors, etc., including fixing in position.(HSR 18.10)

Pressed steel sheet frames (chowkats ), consisting of 2mm thick steel sheet of the specified section,including iron lugs(hold fasts) iron hinges conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for fillings in the frame, and cement concrete 1:3:6 for lugs complete (HSR 18.34) d) Door and window frame of size 114 mm x 50 mm with 35 mm wide double rebate

Providing and fixing in position best indian make (as approved by the Engineer-in-Charge) European type water closet suit with non-concealed 'P' or 'S' trap with or without vent and all other necessary fittings as fully described in item no. 30.3 above [HSR 30.4 (i)] White

Providing and fixing in position best indian make (as approved by the Engineer-in-charge) European type water closet suit, Syphonic type, consisting of- (i) Vitreous China Ware Syphonic Suite with 15 Liters capacity matching chinaware cistern and all internal brass fittings complete with ‘P’ or ‘S’ trap with or without vent (as approved by the Engineer-in-charge). (ii) One Piece seat and lid in hollow black or white plastic fitted with chromium plated hinges and rubber buffers,(to the approval of the Engineer-in-charge). Complete in all respects including cutting and making good the walls and floors [HSR 30.5]

Providing and fixing in position best Indian make (ordinary)lavatory suites, consisting of Lavatory in vitreous chinaware size as given below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary. R.S. or C.I. Brackets for building into wall including painting, 32mm C.P. brass waste with C.P brass chain and rubber plug, 15mm C.P. brass screw down pillar tap with jamnuts or couplings best design (as approved by the Engineer-in-Charge). All fittings best Indian make and; to the approval of the Engineer-in-Charge. All brass work chromium plated and complete in all respect including cutting and making good the walls floors and painting of fittings etc. [HSR 30.41] iv) Size 550mm x 400mm with one no. tap.

Providing and fixing in position best quality stainless steel sinks with complete fittings as fully described in item No.30.51 above [HSR 30.53] (a) size 600mm x 450mm x 200mm

Providing and fixing in position 15mm i/d C.P.brass & bib cocks of best quality (as required by the Engineer-in-charge). [HSR 30.75] (a) Bib cock long body

(c) Bib cock

Providing and fixing in position C.P. brass stop cocks (as approved by the Engineer-in-charge). [HSR 30.76] a) 15mm stop cock (ii) Concealed stop cock with flange

Providing and fixing HDPE water storage tanks of Sintex, Diplast, O.K., Supreme make with covers / lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with sutiable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in-Charge. (except civil work). (HSR 30.119) 1000 Ltr. capacity.

Providing & fixing 2mm thick PVC Sheet for shed with complete fitting from cover including angle, nut, bolts, paints, pipe excavation of earth work, concrete for foundation etc. complete in all respect to the entire satisfaction of Engineer-in-Charge. ( N.S)

Recovery items:- The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Dismantiling of bricks and Removing of Door and windos in the DNIT. In case it is not possible to use this material on the work, the agency can take away this material after approval from employer. This material will be issued at the price quoted by the agency. However the reserve price is as under:- i) Good Bricks @ 4.5/- Each

ii) Brick Bats @ 450/- cum

iii) Door @ 500/- Each

iv) Windows @ 250/- Each Note:- All quantities of the above materials have been worked out on the basis of theoretical quantities laid on this building. However, agency may visit site before quoting rates and assess the extent of retrieved material. There shall be no measurement after actual dismantling and if material after dismantling is found on lesser side, no claim of agency on this score will be entertained and full recovery on the basis of quoted rate and quantity exhibited in the BOQ shall be made. The reserve rates are minimum rates to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price. Note:- 1. In case of any difference in the unit & nomenclature of any of the HSR Items of Civil, P.H. work depicted in this DNIT and that given in HSR, the unit and nomenclature given in HSR shall be applicable. 2. Only reputed make material will be used (make/brand exhibited in HSR and exhibited in approved standard document) as approved by Engineer-in-charge, while executing various items/works at site.

M/s Ashwani Kumar Contractor

The Jai Mata Bala Sundri Coop. L and C Society Ltd

Balwant Singh S/o Sh. Zile Singh