Providing Face Lifting Works to the Toilets of G 1 Ward, Near X Ray Department, Ground Floor and first Floor Toilets located at PRS Building of Industrial Health Centre, HAL BC Including Civil Electrical Works.

Name of the Individual / Firm / Company: * Mandatory

Type of ownership

Details of Constitution or Legal Status such as certificate of incorporation, shops and establishments, Contractor registration No etc.,

Address for correspondence:

PAN No.:

Service Tax Registration No

Goods and Service Tax ID No.

Contact details

Please Enter Contact person Name

Pls Enter Mobile No

Registered Contractor

Average annual financial turn over during the last 3 years, ending 31st March 2024 of the previous financial year [ should not be less than 30% of Amount put to tender]

TURN OVER IN Rs.

Pls Enter Turn over in Rupees for all the 3 years

ESI & PF Nos with proof

Remarks if any

Bank(s) details: [Copy of the cheque leaf to be uploaded]

Related Document to be Uploaded to eProcurement Portal (Note Canceled cheque leaf to be uploaded)

Latest Bankers Solvency Certificate from Nationalized/ scheduled Bank issued NOT before 12 months from the last date of Tender submission

Pls Enter Details to 'Name of the Bank' , 'Date of Issue','Value in Rs

Experience of having successfully completed similar works during last 7 years ending last day of previous month. [Latest work experience certificate may be uploaded] (i) THREE similar completed works each costing not less than the amount equal to 40% of the estimated cost. (ii) TWO similar completed works each costing not less than the amount equal to 50% of the estimated cost. (iii) ONE similar completed work each costing not less than the amount equal to 80% of Amount put to the tender.

Type of Work: [ Incase of private works the same shall be supported with TDS certificate]

Please enter Details for Work No 1

Type of Work: [ Incase of private works the same shall be supported with TDS certificate]

Pls Enter Details for Work No II

work done

Type of Work: [ Incase of private works the same shall be supported with TDS certificate]

Pls Enter Details for Work No III

Details of person holding the power of Attorney (If different from contact person)

Related Document to be Uploaded to eProcurement Portal

Pls Enter Details for Person holding Power of Attorney

DECLARATION I

DECLARATION II

Pls Accept the Delaration II

Specification

Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead, etc., all complete as per direction of Engineer-in-Charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Dismantling doors, windows and clerestory windows (steel or wood) of area 3Sq m and below shutter including chowkhats, architrave, holdfasts, etc., complete and stacking within 50 metres lead, etc., all complete as per direction of Engineer-in-Charge.

Dismantling aluminium / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead, etc., all complete as per direction of Engineer-in-Charge.

Disposal of moorum / building rubbish / malba / similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, etc., complete as per directions of Engineer-in-Charge. Note - item to be applicable in urban areas having directions for restricted hours for movement / plying of load carrying motor vehicle of 3.50 Cu m or more.

Dismantling of flushing cistern and water closet of all types and sizes (C.I. / PVC / Vitroeous China / urinlas / IWC / EWC / hand wash basin) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead, etc., all complete as per direction of Engineer-in-Charge.

Dismantling tile work For thickness of tiles 10 mm to 25mm in floors and roofs / walls laid in cement mortar including stacking material within 50 metres lead, etc., all complete as per direction of Engineer-in-Charge.

Taking down cement / lime palstering of any desription on brick walls inlcuding raking out joints, scrubbing, etc., all complete as per direction of Engineer-in-Charge.

Brick work with common burnt clay machine moulded perforated modular bricks of class designation 12.5 conforming to IS: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand), etc., all complete as per direction of Engineer-in-Charge.

Cement mortar (1:6) plastering 20mm thick for brick / concrete surfaces, finished smooth with trowel including lime rendering for interior faces of walls surfaces including scaffolding, curing, etc., all complete as per direction of Engineer-in-Charge.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.30kg per Sq m, including pointing in white cement mixed with pigment of matching shade, etc., all complete as per direction of Engineer-in-Charge.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) of size [600 x 600]mm with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.30Kg/Sq m including grouting the joints with white cement and matching pigments, etc., The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily, etc., all complete as per direction of Engineer-in-Charge.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18mm thick stone slab over 20mm (average) thick base of cement mortar1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing, etc., all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing & fixing fly proof wire gauze of stainless steel grade 304 (wire guage) of 0.50mm wire and 1.40mm aperture on both sides, etc., all complete as per direction of Engineer-in-Charge.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with Powder coated aluminium (minimum thickness of powder coating 50 micron) built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket, etc., Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, etc., all complete as per architectural drawings and the directions of Engineer-in-Charge. (Glazing, paneling and dash fasteners to be paid for separately)

Providing and fixing With float glass panes of 5mm thickness (weight not less than 12.50 Kgs/Sq m)glazing in aluminium door, window, ventilator shutters and partitions, etc., with EPDM rubber / neoprene gasket, etc., complete as per the architectural drawings and the directions of Engineer-in-Charge

Providing 40mm thick Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps, etc., all complete as directed by Engineer-in-Charge.

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth, etc., all complete as directed by Engineer-in-Charge.

Wall painting with 2 coats of premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams / litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour, etc., all complete as directed by Engineer-in-Charge.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams / litre, etc., all complete as directed by Engineer-in-Charge.

Providing & fixing White vitreous china Orissa pattern water closet squatting pan of approx size [580 X 440]mm or nearest available size along with "S" or "P" trap including dismantling of old WC seat and "S" or "P" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of [430 x 260 x 350]mm and [340 x 410 x 265]mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing wash basin white vitreous china wash basin of size [630 x 450]mm with pedestal completel recessed at the back for reception of pipes and fittings including C.I. brackets, 15mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required, Bottle trap 38mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from the centre of the waste coupling, 77mm breadth with 25mm minimum water seal, weighing not less than 263gms including necessary fittings and fixtures, etc., all complete as directed by Engineer-in-Charge.

Supplying & Fixing of C.P brass stop cock 15mm dia bore concealed of standrd design and approved make conforming to IS 8931, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints, etc., all complete as directed by Engineer-in-Charge.

15mm nominal dia Pipes

20mm nominal dia Pipes

Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS: 13592 type A including jointing with seal ring conforming to IS 5382 leaving 10mm gap for thermal expansion single socketed pipes, etc., all complete as directed by Engineer-in-Charge.

PVC Pipes - 75mm dia

PVC Pipes - 110mm dia for floors

Coupler - 75mm dia

Coupler -110mm dia

Bend -75mm dia

Bend -110mm dia

Supplying & Fixing of C.P brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 grams for 15mm dia bore, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing PTMT towel ring trapezoidal shape 215mm long, 200mm wide with minimum distances of 37mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88gms, etc., all complete as directed by Engineer-in-Charge.

Supplying & Fixing of oval shape of size [450 x 350]mm outer mirror superior qulaity and of rectanguler shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing, etc., all complete as directed by Engineer-in-Charge.

Providing and Fixing factory made PVC door frame made of PVC extruded sections of size [75 x 53]mm, having wall thickness 2.0mm (± 0.2 mm). Both verticals sides of the frame reinforced with PVC profile of cross section size [28 x 30 x 2]mm thickness (± 0.20mm) and [75 x 200]mm long, including reinforcing both ends of the top frame with PVC profile. PVC Door Frame and PVC reinforcement profile to be mitred cut, jointed and fusion welded together, including providing and fixing 3 nos of 125mm long stainless steel hinges to frame, fixing the frame with jamb with required nos & sizes of anchor dash fastener, etc., all complete as per manufacturer's specification and direction of Engineer- in-Charge.

Providing and fixing 37 mm thick factory made PVC Door shutter, styles and rails made of PVC hollow extruded printed and laminated section having overall dimension 115 mm x 37 mm with wall thickness 2 mm (± 0.2 mm) with inbuilt beading on one side, the styles and rails mitred cut and joint at corners by inserting 2 nos PVC profile reinforcement of size 75 mm x 200 mm long with cross section size of 28 mm x 30 mm having wall thickness 2 mm (± 0.2 mm). Styles, rails and reinforcements to be fusion welded together. Only hinge side vertical style to be reinforced with PVC profile reinforcement in full length. Printed and laminated PVC lock rail of size 110 mm x 37 mm having wall thickness 2 mm (± 0.2 mm) to be welded horizontally with the vertical styles after inserting PVC profile reinforcement as in styles and rails, providing with PVC snap fit beading, panels of 100 x20 mm printed & laminated and inserting 2 nos 6 mm dia bright steel rod horizontally with both side threaded and tightened with check nuts and washers, etc., complete, all as per manufacturer's specification and direction of Engineer-in-Charge.

Supplying and fixing approved hardware fittings with necessary screws, nails, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing ISI marked IS : 1341 M.S. pressed butt hinges bright finished with necessary screws, etc., complete: [100 x 58 x 1.90]mm

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws, etc., complete: (Copper oxidized as per IS 1378). [250 x 16]mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws, etc., complete: (Copper oxidized as per IS : 1378). [150 x 10]mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws, etc., complete: 125mm

Providing and Fixing 8mmdia. C.P / S.S Jet with flexible tube upto 1 mtrs long with S.S triangular plate to Eureopen type W.C of quality and make as approved, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing 100mm nominal dia circular type PTMT grating of approved quality and colour, etc., all complete as directed by Engineer-in-Charge.

Constructing brick masonry road gully chamber [50 x 45 x 60]cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including [500 x 450]mm pre-cast R.C.C. horizontal grating with frame as per standard design With common burnt clay F.P.S. (non modular) bricks of class designation 7.5, etc., all complete as directed by Engineer-in-Charge.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) [455 x 610]mm internal dimensions, total weight of cover with frame to be not less than 38kgs (weight of cover 23kgs and weight of frame 15kgs), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size), inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete, etc., complete as per standard design: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5, etc., all complete as directed by Engineer-in-Charge.

Rupees Fifteen Lakh One Thousand Two Hundred Six and Eighty Three Paise Only

Supply, fixing directly to the ceiling/wall using suitable mounting arrangements testing & commissioning of surface mounting Decorative type 10W LED mirror light fitting, including driver, the driver shall have PF >0.9 and Colour temprature shall be ≥5700K, THD <20% operating on single phase 230V voltage 50 Hz AC supply with voltage range 140-270V including necessary interconnections complete in all respect and as directed by EIC. The lighting fixture shall be Bajaj make Model-BCLSB 10W WH/Equivalent make in other approved makes.

Supply and fixing on existing wall / ceiling, testing & commissioning of surface mounting, Batten type 1X18W/20W T8 LED Tube light (four feet) Luminaries with minimum lumens output Efficacy of minimum100 lm/W., comprising of white powder coated CRCA sheet steel housing, operating on single phase 230V 50Hz AC supply, built-in electronic driver, LM 79 certification for luminaire. Other standard accessories including necessary inter-connections and supply of 1 No of 18/20W T8 LED Tube, complete in all respects and as directed by engineer-in-chage. Make & model: The LED tube & batten shall be of CROMPTON-IGP161LT8-16.1XT8+LT8-20-865/Equivalent model of approved make luminaries which meets the above technical specification. complete in all respect and as directed by Engineer-in-charge.

supply, fixing and commissioning of 5 star rated, 25 ltrs capacity Vertical Mounted Water storage Geyser with porcelain enamel glass lined tank (Super polymer high performance inner container), PUF insulation, thermostat, pressure release valve, fusible plug, pilot lamp as per IS-2082 with ISI mark on the unit and guarantee for not less than one year of any approved make etc,.

Supply, installation, testing & commissioning of 300mm dia 900 rpm heavy duty exhaust fan of any approved make with louvers, connecting cord with 6A, 3 pin plug top and with all necessary accessories, including making wall openings and replastering to smooth finish with matching paint etc., complete in all respects and as directed by Engineer-in-charge.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required

2X4Sq. mm 1X4 sq mm earth wire

2X2.5Sq. mm 1X2.5 sq mm earth wire

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

20 mm PVC conduit

25mm PVC conduit

Wiring for light point / fan point / exhaust fan point/call bell point from nearest switch box with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, fan regulator, modular plate, suitable GI box and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. (as per detailed CPWD specifications for Group C wiring)

Wiring to single light point controlled by 1 No 6A, 250V gr. flush type modular SP switch complete in all respects.

Wiring to two light point controlled by 1 No 6A, 250V gr. flush type modular SP switch complete in all respects.

Wiring to exhaust fan point using 6A, 250V gr. flush type modular SP switch housed along with other lighting switches/separate switch box if required and 3pin 6A, 250V gr. modular type socket housed near the exhaust fan complete in all respects.

Supplying and fixing suitable size GI Box with modular plate and cover on front on surface or in recess, including providing and fixing 6 pin 5/6A & 15/16A modular socket outlet and 15/16 A modular switch, connections etc., as required.

Rupees Three Lakh Seventy Two Thousand Five Hundred Sixteen and Eighty One Paise Only

Rupees Eighteen Lakh Seventy Three Thousand Seven Hundred Twenty Three and Sixty Four Paise Only

Approximate Amount Put to Tender

Rupees Three Lakh Thirty Seven Thousand Two Hundred Seventy and Twenty Five Paise Only

Rupees Twenty Two Lakh Ten Thousand Nine Hundred Ninety Three and Ninety Paise Only