CA NO GE/ND79/202122 PROVN OF 02 X TOILET BLOCK INCLUDING ALLIED SERVICES OF IHQ MOD ARMY TPT UNIT ASC UNDER GE NEW DELHI

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out etc and getting out in any type of soil incl removing the surplus soil or unserviceable material out side the MOD land complete all as specified & directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out. NOTE : Making good the disturbed surface shall be deemed to be included in rate quoted by contractor.

Returning filling, including spreading, levelling, watering and well ramming in layers not exc 25 cm each layers complete all as specified & directed.

M & L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified & directed.

M&L for lean concrete 1:4:8 type D2(using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete M-25 (Design Mix) using 20 mm graded aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete M-25 (Design Mix) using 20 mm graded aggregate as in columns, pillars, piers,posts and struts etc complete all as specified and directed.

M&L for reinforced cement concrete M-25 (Design Mix) using 20 mm graded aggregate as in beams, cantilevers, bressummers,lintels etc complete all as specified and directed.

M&L for reinforced cement concrete M-25 (Design Mix) using 20 mm graded aggregate as in slab supported on walls, beams and columns in floors, roofs, landings,balconies, canopies, chajja, deck slab and in shelves and the like complete all as specified and directed.

M&L Form work to sides of concrete foundation, footings,bases of columns, raft and raft beams sides and soffits (if any) of foundation and plinth beams and similar work vertical or batter finished rough surface of concrete complete all as specified and directed.

M&L Form work square, rectangular to sides of pillars, posts,sturts, piers,columns and stanchions and similar work vertical or batter finished rough surface of concrete complete all as specified and directed.

M&L Form work to sides and soffits of floor or roof beams, beams haunchings, girders, bressummers, lintels, cantilevers, shelves including sup-ports, overhangs, etc. also splays between floors and beams etc. finished rough surface of concrete complete all as specified and directed.

M&L Form work to soffits of suspended slab such as roof slab floor slab landings and similar work flat for fair finished surface complete all as specified and directed.

M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide finished rough surface of concrete complete all as specified and directed.

M&L for premix/ready-mix plaster 15mm thick on brick or concrete surfaces of walls in CM 1:4 finished even & smooth without using extra cement over a coat of UltraTech seal and dry 5 plush as bonding agent including necessary form work safety precaution up to multi storey of bldgs. including necessary scaffolding, framed work and safety precautions complete all as specified & directed.

M&L for premix/ready-mix plaster 10 mm thick on brick or concrete surfaces of ceiling,chajjas,columns, beams and similar work in CM 1:4 finished even & smooth without using extra cement over a coat of UltraTech seal and dry 5 plush as bonding agent including necessary form work safety precaution up to multi storey of bldgs. including necessary scaffolding, framed work and safety precautions complete all as specified & directed.

M&L brick work with fly ash bricks of straight or curved on plans exc 6m mean radius built in CM 1:6 complete all as specified.

M&L for brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:6 complete all as specified.

M&L brick work with sub class 'B' bricks, straight or curved on plan exc 6.00 m mean radius built in CM 1:4 as in manhole, drainage etc. complete all as specified.

M&L for preparation of new plastered ceiling surfaces and applying two coats of distemper oil emulsion white/tinted over one coat of primer complete all as specified & directed.

M&L for preparation of new plastered wall surfaces and applying two coats of distemper oil emulsion, white or tinted over one coat of primer including 3mm thick wall care putty complete all as specified & directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint (weather proof) having VOC less than 50 m/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified & directed. Make :- Apex Ultima from Asian, Acroguard 3X from Acro Paints or Equivalent.

M&L TMT bars 10mm dia and over, cut to length, bent to shape required,including cranking, bending, spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as directed by Engr-in-Charge.

Ditto as per item no 23 above here-in-before but 6 to 8 mm dia.

Ditto as per item no 23 above here-in-before but 6mm dia and over up to and including 10mm dia as in stirrups, spacers and binders.

M&L for black or any coloured granite (of any type) work 18-20 mm thick table rubbed and polished as in platform, face lifting of lift area and like , machine cut laid over and including 15 mm thick screed bed in CM 1:4, laid and jointed with grey cement slurry and incl pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade including cutting, rounding edges and polishing complete.

Ditto all as per item No 26 above but as in vertical surfaces such as dado/skirting laid over and including rendering premix/ready-mix plaster 10 mm thick on brick or concrete surfaces of ceiling,chajaas,columns, beams and similar work in CM 1:4 finished even & smooth without using extra cement over a coat of UltraTech seal and dry 5 plush as bonding agent jointed with grey cement slurry and incl pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including cutting and polishing complete.

S&F medium grade galvanised steel tubing with all fittings fixed to walls and ceilings or laid in floors for 15 mm bore GI tubings.

S&F medium grade galvanised steel tubing with all fittings fixed to walls and ceilings or laid in floors for 20 mm bore GI tubings.

S&F for gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed for 15mm dia pipe (ISI Marked) .

-Ditto- as per item No 30 above here-in-before but for 20mm dia pipe.

S&F PTMT ball valves high pressure with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe of 20mm dia.

S & F PVC (SWR) pipes single socketed, 110 mm bore in any length with rubber ring joints, fixed to walls,floors including necessary screws, clamps up to six story building including taking down old pipe.

S & F PVC (SWR) pipes single socketed, 75 mm bore in any length with rubber ring joints, fixed to walls,floors including necessary screws, clamps up to six story building including taking down old pipe.

S&F PVC (SWR) bends/Tees of any radius of 110 mm bore.

S&F PVC (SWR) bends/Tees of any radius of 75 mm bore.

S&F PVC (SWR) vent cowl of 110 mm bore.

S&F PVC (SWR) vent cowl of 75 mm bore.

S&F 110mm bore PVC (SWR) 'P’ trap

S&F, SWR nahani trap/ floor trap with Cockroach Proofing CP grating with or without hole including jointing to waste pipes , fixed in cement concrete type B-1 (1:2:4), dia of outlet 75 mm, complete all as specified.

S&F salt glazed stone ware gully traps square or rounded mouthed type P or S of size 150 x 150mm incl excavation earth work conc in Beds, surrounds kerbs & CI grating etc complete.

M&L for 75 mm thick PCC 1:3:6, type C-1 (using 20 mm graded stone aggregate) as in sub base of flooring etc. finished rough surface without using extra cement complete all as specified.

M&L 50 mm thick cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in floor finished even and smooth surface without using extra cement complete all as specified and directed.

M&L for PCC 1:3:6, type C-1 (using 20 mm graded stone aggregate) laid over hard core as in plinth protection complete all as specified.

M & L for PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in benching, copings, channels, slightly chamfered or rounded on edge including necessary use of form work complete all as specified & directed at site.

M&L for framed work such as grills, gratings etc with ends of bars shouldered and/or riveted, welded or forged into spikes framed guard bars, barred doors & walk ways railings frame work of water tank and similar work confirming to Fe-290 Gde -E-165 fixing up to six story building on wall.

Supply only liquid waterproofing compound

S&F Vitreous China, semi-pedestal pattern (Anglo-Indian Type) wash down water closet white complete with provision of lime concrete bed incl valveless syphonic action type PVC low level flushing cistern with inlet ball valve float & handle incl. brackets of 10 ltrs capacity complete with plastic water closet seat white closed pattern with flat bottom & cover & mild steel chromium plated or aluminium hinges device & flush pipe of polythene of low or high density of PVC 32mm dia for low level PVC cistern. Make:HINDWARE/PARRY WARE/CERA Ist quality.

S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests white complete with provision of lime concrete bed incl valveless syphonic action type PVC low level flushing cistern with inlet ball valve float & handle incl. brackets of 10 ltrs capacity complete with plastic water closet seat white closed pattern with flat bottom & cover & mild steel chromium plated or aluminium hinges device & flush pipe of polythene of low or high density of PVC 32mm dia for low level PVC cistern. Make:HINDWARE/PARRY WARE/CERA Ist quality.

S&F in repair vitreous china wash basin white oval type size 600 x 480 mm white in colour, fitted in counter platform of granite stone of 18-20 mm thick,of approved colour, area of granite slab exceeding 0.50 Sqm but not exceeding 1.00 Sq m in single piece, corners/edges shall be rounded off, including provision of brass chromium plated waste coupling for WHB with long screwed and shanks and fly nuts, flanged end bedded in red lead and other end fixed, PVC waste pipe, 32mm dia ,med grade, pipe with fittings fixed in wall connected to floor trap for drain out, complete including provision of pair or bracket of angle iron 35x35x6mm duly painted with two coat of synthetic enamel paint over one coat of red oxide zinc chromate primer and embedded one end of bracket in PCC 1:2:4 type B-1 bed blocks and cutting for and pinning in ends of brackets in walls and making good all as specified.

S&F in repair vitreous china urinals, half stall type white including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long bras screws pointing around urinal back in cement fixing automatic flushing cistern with brackets, flush pipe, gratings and union for discharge pipe complete all as specified.

S&F brass chromium plated towel ring square with round flange fixed with steel screw on wall as specified complete all as specified and as directed.

S&F, chromium plated towel Tubular towel rail, 20mm dia, D type, 60cm long fixed with steel screw on wall as specified

S&F 15mm dia Bib taps, cast copper alloy fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F 15mm dia stop valves, cast copper alloy, chromium plated fancy type screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete fixed to wash hand basin.

S&F 15mm dia Pillar taps, cast copper alloy, fancy type long body/long neck with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete fixed to wash hand basin complete all as specified and as directed.

Supply and fix brass chromium plated angle valve long shank with cup suitable for 15mm bore pipe, complete all as specified .

S&F chromium plated shower rose of size 125mm with or without swivel joints any type including chromium plated shower arm fixing to steel pipe and union completed .

S&F 15mm size PVC connection 450/600mm long incl PTMT nuts and PVC washers at both ends screwed both ends for iron pipe.

S&F brass chromium plated soap dish fixed with steel screw complete all as specified

S&F 6 mm thick bath room mirror of size exc 1 sqm but n.ec 4 sqm each fixed with 3mm PVC plastic sheet including stainless steel rounded bolts, rounded decorated edges of glass all as specified and as specified. (Make - Modi guard)

S&F rotational moulded polythene water storage tanks in double layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I of capacity 1000 ltrs incl making connection with fitting for inlet & outlet pipe.

S&F powder coated (minimum power coating 50 micron) to aluminium frame / guiding rail for sliding or side hung windows/ventilators frame including jointing cleats,glazing clips and fixing complete with one or more rebates for fixing etc complete all as specified.

S&F powder coated (minimum powder coating 50 micron) to aluminium glazed/gauzed window and ventilators shutters, side hung type( or sliding type) without sash bars, aluminium section weighting 0.55 kg per mtr including necessary joining cleats, glazing clips, rubber packing, aluminium snap beading, screws including fittings such as peg stays 150mm long (2 Nos) to each leaf, hinges 100mm long (2 Nos) each leaf and suitable handle (1 no.) to each leaf complete all as specified.

S&F sheet frosted glass and glazing with rubber beading and aluminium beading in squares n exc 0.50 sqm in each pane of 4 mm thick complete all as specified and directed.

S&F 100/150 mm size aluminium anodised barrel tower bolt of extruded section & fixed.(ISI Marked)

M&L for non skid ceramic tiles of approved colour and design 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed..

M&L for Glazed ceramic tiles of approved colour and design in vertical surfaces 300x450x7mm thick including provision of high lighter tiles/boarder and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick rendering in cement mortar 1:4.

M & L Cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipe of 150 mm bore after they are laid and tested.

M & L Salt glazed stone ware ( SGSW ) drain pipes, Grade ‘A’ 150 mm bore, laying level or to falls in trenches, on concrete bed or directly on hard grounds and making joints and testing complete.

S&F PFRC circular manhole (medium duty) cover with frame of size 551 to 650 mm dia conforming to IS: 12592 and IS:1726, factory made complete all as directed and as approved by Engr-in-Charge

M&L for solid PVC Door Frame of size 50mm x 47mm wood grain printed PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with printed sheet as per specification and drawing.

S&F for factory made solid PVC moulded door shutters (with particle board core), 28 to 30mm thick (Stiles) with 2, 4, or 6 raised panel (as ordered) design with 2mm thick moulded prelam PVC sheet on the front face and 2mm prelam PVC sheet on back face, supply and fixing in frame at site as per the specification and drawing.

S&F for aluminium alloy anodised sliding door bolt, of size 200mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of cast aluminium alloy,complete all as specified.

S&F for stainless steel butt hinges of size 100mm fixed complete all as specified.

S&F Aluminium handles, Extruded aluminium alloy handles, fabricated type, anodised 150 mm long, complete all as specified and directed.

S&F Hasp and staples,size 100mm/150mm, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws.

S&F Stainless steel wire cloth of size 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanized wire staples.

M&L for broken stone boulders hard core, broken to gauge n exc 63 mm laid, spread and consolidated compacted as in plinth protection and similar work complete all as specified.

M&L for point wiring with PVC insulated sheathed multi stranded FRLS type copper conductor cable of size 1.5 Sqmm 1100 V grade including one run of PVC insulated unsheathed multi stranded FRLS type copper conductor cable of size 1.5 sqmm as earth continuity conductor connected to common earth dolly in and including PVC concealed conduit 20 mm dia medium grade ISI marked and its accessories including provn of new factory made pressed steel modular switch/terminal box of suitable size and new modular front & back plates of approved colour/model of suitable size for housing the modular switches, sockets, fan regulators for the following :-

(a) One light/fan point controlled by one no, one way 5 Amp switch. Make:-RR/Polycab/Havells

(b) One three pin 5 Amp socket outlet point controlled by one no, one way switch on same board Make:-RR/Polycab/Havells

All as per item No. 80 here in before but with 2.5 sqmm (for phase, neutral) and 2.5 sqmm (for continuous earth wire) cable for one 15/16 amp socket out let point on independent board. Make:-RR/Polycab/Havells

S&F modular switch 230/250 volts grade one way (as catered in point wiring above) of following rating :-

(a) SP 6 Amp rating Make:-Legrand/Indoasian/Havells

(b) SP 16 Amp rating Make:-Legrand/Indoasian/Havells

S&F modular socket out let shuttered type flush mounting type, 230/250 volts grade (as catered in point wiring above) of following ratings:-

(a) 6 Amp 2/3 pin multipurpose type. Make:-Legrand/Indoasian/Havells

(b) 16 Amp 2/3 pin multipurpose type. Make:-Legrand/Indoasian/Havells

S&F ceiling rose 3 terminal / PVC insulated body ISI Marked all as specified.

Supply, laying, jointing, testing and commissioning LT under ground cables of cross sectional area 10 Sqmm x 4 core, 1100 volts grade, XLPE insulated and PVC sheathed, heavy duty armoured with multistranded copper armoured conductors, IS - 7098 laid in trenches/ducts/fixed on poles/walls/laid under roads/paths/drain/culverts or encased in GI pipe complete all as specified and directed

Supply local sand cushioning , with dry and clean sand, over and under the under ground cables in trenches, ducts for cable protection including consolidation, 80mm thick to the authorized width as per SSR Part-I before laying of cable and 150mm thick after laying of cable complete all as specified and as directed

M&L for Best quality, locally available, sub class ‘B’ bricks (Old Size) for cable protection cover, laid flat and dry in trenches over the cable , perpendicular to the direction of cable complete all as specified and as directed by Engineer-in-Charge.

Returning filling including spreading, levelling watering and well ramming in layers n. exc 25 cm thick in any type of soil complete all as specified.

S&F factory made TPN DB's double door made out of 2.15 CRCA mild steel sheet with insulating materials like polyester epoxy coated surface mounting 4 way TPN 415 Volts, IP 43 , 25 KA with suitable busbar, neutral link & earth link suitable for MCCB TPN 63 A as incomer & MCB SP/TP as out going complete all as specified. MAKE-INDOASIAN CAT NO-811890 or equivalent Havells/Legrand .

Supply and fixing MCCB, 3 pole,neutral 415 volt of capacity 40/63 Amp, breaking capacity not less than 25 KA , Icu=100% Ics thermal magnetic type adjustable type 80 to 100 % confirming to IEC-60947-II, IS-13947-II , including thimbles, nuts, bolts ,washers etc and connections, replacement of thimbles, minor parts like nuts bolts washer etc. all as specified and directed by Engr-in-Charge Make : Legrand/Havells/Indoasian-811220.

S&F MCB SP 6 Amp to 32 Amp 10 KA.240 volts all as specified. MAKE:-Legrand/Havells/Indoasian

S&F in Metal exhaust fan 225 mm(Metal Body)size suitable for 240V, 50 Hz,1350 rpm single phase AC supply including fixing on wall with nut, washer etc complete and necessary electrical connection from ceiling rose to fan connecter with three core sheathed wire of required length including fan louvers. Make:-CG Cat part no TRANS AIR 9" white 225 mm . Make: Havells/Bajaj

S & F iron and aluminium exhaust fan louver shutter suitable for 9 inch 225 mm sweep metal exhaust fan of cross section 12''x10.5'' inches/as per the site requirement complete.

S&F LED Tube Light of 18 Watt 230Volt(size 4 ft) , box type complete with LED Tube Light 18 Watt & all accessories internally prewired including connecting up with three core sheathed flexible copper conductor cable of suitable size complete all as specified : Make: Product Code CAT NO-HLB-33-20-CW-IP of HALONIX or equivalent in Havells/Phillips/Crompton-LCTL-18 CDL

S&F inverter type LED batten of 9 W (2 ft.),extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver in AC complete all as specified. Make: CG make cat part No. LCTL-9-CDL or equivalent in Havells/Phillips

Ex Serviceman Enterprises

MRITUNJYA ASSOCIATES