Development of aCommunity Hall at Moolakothalam Rayapuram Chennai

Amount

Dismantling R.C.C.works,carefully clearing away the debris as directed during execution. The dismantling of concrete as per PWD schedule of rates are to be adopted wherein a part part of the concrete only is to be dismantled and the remaining part of the concrete has to be retained structurally safe.

Clearing scrub Jungle and Surface dressing of the ground. The rate including hire charges of all machineries, removing of all rubbish from site, lead upto 50m, transportat charges and labour charges etc., complete complying with standard specification.

Earthwork excavation and depositing on banks with intial lead of 10 m, and intial lift of 2m, in hard stiff black, cotton soil, hard red earth, shales, Muram, gravel, stony earth and earth mixed with small size boulders etc, as per SS 20B, excluding hard rock required for blasting inclusive of shoring shuttering, bailling out of water where ever necessary and including refilling consolidation etc, Complete in all respects complying with relevant standrad specification and as directed by department officers

Depth 0m - 2.00m

Depth 2m - 3.00m

Carting away surplus excavated earth available with in the campus is to be carted to a lead of within 10 KM from site. The rate shall include loading into the tipper/ lorry, transporting and unloading, leveling and the earth scooped by bulldozers grading etc.,complete with all respects complying with relevant standard specification, as directed by the Departmental Officers.

Providing Pre construction Anti termite treatment for the building including all chemicals as per standard specifications. Labour charges for preparing the areas for treatment spraying chemicals and other incidential charges etc., complete. The rate shall be inclusive of giving anti-termite treatment to the building for the following four stages including breaking the termite mounds making holes with crow bars at an intervel of 12"to a depth of 8" in the periphery of building and pouring chemicals etc., complete as per ISI 6313-1981 and. The antitermite chemicals used should have 0.5% concentration with 3L solution for the entire operation etc. as directed by the Engineer incharge and including cost of chemicals labour transportion etc.,

Stage:1 Spraying Anti-termite treatement chemicals solution for the foundation before laying the foundation concrete bottom and sides of the foundation.

Stage:2 Spraying anti-termite chemicals solution to the grade beams level spraying has to be done for the grade beams brick masonry in the superstructure in contact with back fill earth.

Stage:3 Spraying anti-termite chemicals solution on sand for the flooring before laying the flooring concrete. The treatment has to be carried out on the sand filling the basement after leveling operation is over.

Stage:4 Spraying anti-termite chemicals solution around the building outside of the building by making crow bar holes at an intervel of 12" to a depth of 8" around the building before laying the plinth projection. This holes has to be be closed after the treatment.

Providing and laying plain cement concrete 1 : 4 : 8 ratio of (1 cement , 4 sand and 8 graded stone aggregate 40mm nominal size) in foundation and basement including dewatering wherever necessary and laid in layers not more than 15 cm thick and consolidation etc. The rate includes the cost of materials, labour charges, lifting charges, loading & Unloading and Transportation etc., complete and as per the standard specification.

Construction of Wet Mix Macadam 150mm compacted thickness in two layers by providing , laying , Paving , and compacting of aggregate gradation satisfying to Table 400-13 of MORTH and satisfying the physical paraeteres as per MORTH Table 400-12, mixing in a Wet Mix Plant of 200 tonne capacity at OMC , carriage of mied material to work site and laid in sensor pavers to the required line and grade as per the drawing and compacted with vibratory roller of 8-10 tonne to achieve the desired density of 98% of Maximum dry density and as per the direction of the Engineer-In-Charge of work.

Supplying and Filling with M - sand in foundation and others sub structures for 100mm thick and well watered, rammed and consolidated by power compacter. The rate includes the cost of M sand, compacting with mechanical compactors, labour charges for leveling, loading & Unloading and Transportation charges etc., complete and as per the standard specification.

Supplying and erecting centering for sides and soffits including supports and strutting up to 3.30 m height with all cross bracing for plane surfaces as detailed below, using mild steel sheets of 90 X 60 cm 10 gauge stiffened with MS angle of 25 X 25 X 3mm for boarding, laid over adjustable span & jacks and supported by 50mm dia pipes for general pipes scaffolding systems @ a spacing of 1.20m c/c and vertical connected at a height of 2.0m c/c including 'C' & 'U' clamps and base receiver cup at bottom for connecting pipes etc and removable systems etc., the rate including cost of all materials, labour charges, wastages, placing, transportation, lead & lifts, tools & plants, fuels, fixing in position at all levels, heights, masking tape in sheet joints, consumables, etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

For column footing plinth beam bed blocks templates staircase, steps piers, raft beam, raft slab etc.

For Plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as rectangular or square rcc columns, sunshades, top and bottom slab of rcc boxing, etc.

Supplying, fabricating and fixing in position of steel Fe 550 grade Reinforcement for all RCC work with Thermo Mechanically Treated Bars (TMT) conforming to IS 1786 of latest version according to drawings and binding the reinforcement with 18 gauge double fold GI binding wire and providing Concrete cover blocks to maintain the cover as required. The rate including cost of all materials, bending, tying grills, placing, transportation, lead & lifts, tools & plants, fuels, all materials, labour charges, wastages , laying at all levels, fixing in position, cost of cover blocks and GI binding wires etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Providing and Laying M 30 Design Mix for all reinforced cement concrete with minimum cement content conform to IS 456-2000 using ordinary Portland cement of grade 53 from approved manufacturer, manufactured sand, 20 mm and down graded size coarse aggregates, necessary approved admixtures as per requirement. works for Footings, Grade beam, retainning wall drain wall & raft , Plinth beams, Column, Grade slab, Roof slab & beam, Column drops, Pergola, Staircase waist and landing slab lintel, Sunshades, parapet Cum drops, Steps, canopy, window boxing slab, Loft, fins facia Planter box, machine foundation, elevation features and other similar structures etc..excluding necessary centering, shuttering and reinforcement which shall be measured and paid separately under relevant items. in-charge The rate including cost of all designing the mix, batching plant, mechanical mixing, transporting and placing at all levels, leads, lifts, tools & plants, fuels, all materials, labour charges, wastages , laying, pumping the concrete to all levels, providing sleeves / openings in RCC slabs, compaction by vibrator, gunny bags for curing etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge

Terrace

Supply and constructing cement concrete solid block masonry work at all levels in cement mortar 1:5 (1 of Cement : 5 of manufactured sand ) using Portland Pozzolana Cement standard size of 400 x 200 mm and 200 mm thick of solid cement concrete with minimum compressive strength of 5 N/Sq.mm.conforming to IS 2185 or equivalent BS and Fly ash conforming to IS : 3812 (Part III)-1966* may be used for part replacement of fine aggregate up to a limit of 20 percent complete and as directed. Concrete blocks manufactured under strict quality control conditions using modern rugged block casting and stripping machine with the latest moulding techniques etc,. only shall be used. The rate including cost of all materials, labour charges, wastages for working at all levels with necessary lead and lifts, transportation charges, loading, unloading, scaffolding, staging, curing, fuel, consumables as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge

GF, Compound Wall, Toilet

Terrace

Supply and constructing cement concrete solid block masonry work at all levels in cement mortar 1:5 (1 of Cement : 5 of manufactured sand ) using Portland Pozzolana Cement standard size of 400 x 100 x 200 mm of solid cement concrete blocks, with minimum compressive strength of 5 N/Sq.mm. conforming to IS 2185 or equivalent BS and Fly ash conforming to IS : 3812 (Part III)-1966* may be used for part replacement of fine aggregate up to a limit of 20 percent. Concrete blocks manufactured under strict quality control conditions using modern rugged block casting and stripping machine with the latest moulding techniques etc. only shall be used. Rate to include all materials, labour charges, wastages for working at all levels with necessary lead and lifts, transportation charges, loading, unloading, scaffolding, staging, curing, fuel, consumables as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge

First Floor

Second Floor

Plastering 10 mm thick for ceiling including slabs, beams and column drops and staircase waist slab, sunshade, drops, chajjas etc.. with cement Mortar 1:3 (1 of Cement : 3 of P sand) according to the specification. The Rate including Cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, scaffolding, stagging, providing drip bands, moulds to any size and shape as shown in drawings tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Plastering of 12 mm thick for Internal walls with cement mortar 1:4 (1 of cement : 4 of fine P.sand) according to specifications. Rate shall include for providing GI mesh of nominal thickness at the junctions of masonry and concrete works to a width of 100 to 125mm including tying in position with suitable clamps/screws. Rate including all materials, labour charges, wastages with necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, scaffolding, stagging, tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Plastering 15 mm thick for external surfaces with cement mortar 1:4 ratio (1 of cement : 4 of fine P.sand) including water proofing compound of “CICO No.1 or equivalent“ as per Manufacturer's Specification with sponge finish (washed sand finish) all complete as per specification and as directed.Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, scaffolding, stagging, providing drip bands, moulds, grooves to any size and shape as shown in drawings tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supply and painting of two coats of Plastic emulsion paint of approved shade and colour over one coat of DCP Primer including one coat of Acrylic Wall Putty with DCP Primer.Rate including all brush, roller, ladder, scrapping, washing, materials, labour charges, wastages , cleaning, necessary lead and lifts, scaffolding, stagging, working at all levels, elevations, transportaion charges, loading, unloading, curing, sanding, touchup putty, surface thoroughly cleaned and wetted before painting as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supplying and painting of 2 coats of weather proof exterior emulsion with high sheen, anti algal properties over one coat wall exterior primer of approved quality and shade etc., complete.Rate including all brush, ladder, scrapping, washing, materials, labour charges, wastages , cleaning, necessary lead and lifts, scaffolding, stagging, working at all levels, elevations, transportaion charges, loading, unloading, curing, sanding, touchup putty, surface thoroughly cleaned and wetted before painting as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Providing guildeline road marking kerb painting (special acrylic medium pigmented ) involving cleaning the surface free of dirt and loose particles applying one coat of primer and applying one layer of 20 to 25 microns. Rate shall include for all materials & labour components etc., as complete all respects complying with relevant IRC specifications, as directed by the Engineer-in-charge.

Providing And Laying of Hot Applied Thermoplastic Compound 2.5 mm Thick Including Reflectorising Glass Beads @ 250 Gms Per Sqm Area, Thickness of 2.5 mm Is Exclusive of Surface Applied Glass Beads As Per Irc:35 The Finished Surface To Be Level Uniform And Free From Streaks And Holes Etc Completed As Per Mort& H Specification.

Supplying and laying of Ceramic tiles of size 305 x 305 x 6mm for flooring approved make and quality with plain/colour with base mortor in CM 1:3, 10mm thick and pointing with white cement by adding suitable colour pigments including finishing, jointing and polishing with neat finish etc., complete. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supplying and fixing Dadooing the wall with ceramic tiles of approved quality, colour and design joint free of size 600x300x10mm thick of approved make, in all floors over a base layer of cement mortar 1:2 (one cement: Two sand) 10mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40 kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Flooring with Joint free double charged vitrified tiles of approved quality, colour and design joint free of size 600 x 600 x 8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (one cement three sand) 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40 kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officers. Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supply and laying with best quality the following materials of Machine Polished granite slab for wash basin counter top of not less than 18 mm thick (Jet Balck) including cutting for wash basin and edge polishing to be set in CM 1:4 (1 of cement : 4 of manufactured sand) 20 mm thick including finishing the joints with white cement slurry, cutting, edge chamfering to approved shape and polishing rough, medium, nice and tin-oxide polish. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts working at all levels, transportaion charges, loading & unloading, preparation of surface, ncessary haccking in RCC surface, cutting to required shape, edging, tools and plants, fuel, curing, cleaning, acid wash over finished surface, protection with Gypsum / Pop layer over plastic sheet and removing the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge

Supply and Laying flooring with best quality approved colour 18mm thick Flamed Steel Grey Granite Slab for Staircase and Ramp flooring of size not less than 1200 x 600 mm machine cut and set in C.M 1:4 (1 of cement: 4 of manufactured sand) 20 mm thick topped with white cement slurry (for surface contact of the bottom of the granite slab) as per approved pattern, including finishing the joints with matching shade, cement slurry, cutting, edge chamfering and polishing rough, medium, nice and tin-oxide polish.Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading. preparation of surface, ncessary haccking in RCC surface, cutting to required shape, edging, antiskid grooves,tools and plants, fuel, curing, cleaning, acid wash over finished surface, protection with Gypsum/Pop layer over plastic sheet and removing the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Providing dadoing with machine cut polished best quality approved colour granite slab (Synthetic grey,Parasise colour) of thickness not less than 20mm of size 1200x600 / 900x600 mm, set in C.M 1:3 ( 1 of cement : 3 of manufactured sand ), thickness not less than 20 mm including pointing with matching colour of Latapoxy SP100 and fixing with stainless steel clamps 6mm dia.and 100 mm long welded with 40 mm and 25 mm long pieces at two ends to right angle, the former with horizontal position to be embedded in brick wall / concrete surface and the later with vertical position to be inserted and caulked in to the holes of the slab, drilled for the purpose, both forming 'T' shape and cement grouted including edge polishing wherever required and forming groove at joints as directed at all levels.Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, filleting/ chamfering of the edges along with partial recessing of the skirting into masonry, preparation of surface, ncessary haccking in RCC surface, cutting of tiles to required shape, edging, tools and plants, fuel, curing, cleaning, acid wash over finished surface, protection with Gypsum / Pop layer over Plastic sheet and removing the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.Rate shall include for preparation of base surface, cleaning, chamfering, edge polishing, with tin-oxide / high gloss factory polish, provision of 'V' shaped notch cuts along the horizontal and vertical joints of specified size as detailed in the drawing protection with Gypsum/POP layer over plastic sheet etc. complete, as directed.

Supplying and fixing UPVC windows of casement type Open from the profile the size of outer frame 60mm x58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% Corrosion free,the profiles are multi Chambered sections with wall thick of 2mm. TheEPDM rubber covered with over all the edges of frame and shutter the shutter .will be provided with Espag multi power point locks and also it operates with Handle. The Corners and joint should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thk should be provided to the shutter and it should not allow leakege of water even at most ranging storms and should have key lockable action, security protective hinges , strong locking system and as per size for arresting noise and energyloss. The connecting mechanism between sash and windowshould be fixed to the wall with 100% packing with screws and silicon Packing all round the frames. The window should be got approved from the Executive Engineer before use on work.

Supplying and fixing UPVC Louvered Ventilators of from the profile the size of outer frame 60mm x58mm and shutter profile size of 60mm x 78mm both profile are reinforcement with GI/1mm 125GSM and 100% Corrosion free,the profiles are multi Chambered sections with wall thick of 2mm.The EPDM rubber covered with over all the edges of frame and shutter . The Corners and joint should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thk should be provided in the Louvers.The window should be fixed tothe wall with 100% packing with screws and silicon packing all round the frames. The Ventilator should be got approved from the Executive Engineer before useon work.

FOAMED PVC DOOR FRAME Specification: Providing factory made pre-laminated FPVC (Formed Polyvinyl Chloride) Door Frame of the size 105 x 40mm with a wall thickness of 10mm made out of extruded rigid FPVC profile mitre joined with 6 Nos. of 5mm long screw. The door frame shall be fixed to the wall by using 80mm long screws through the frame with the help of PVC fasteners of 3 Nos. to be provided for each vertical member, GI stiffeners of ('U' channel of size 29 x 9, 1mm, 150mm long) - 3 Nos. at hinge point, frame reinforcement of ('U' GI channel of size 46 x 22 x 0.6mm), bottom tie rod of ('U' GI channel size of 15 x 15 x 1mm), etc., complete complying with the standard specification. The door frame should be got approved from the Executive Engineer before use on work

Providing of 35mm thick factory made pre-laminated ABS(Acrolynitrile Butadiene Styrene) Door Shutter moulded indifferent designs, consisting of all round frame made out of water proof solid foam PVC bar of size 20 x32mm, reinforcedby 32 x 32mm - 2 Nos., for vertical made out of LVL(Laminated Veneer Lumber), core material of 32mm thickhigh density craft paper honey comb board, sandwiched onboth sides with pre-laminated ABS sheet thickness of 1.5mm.PVC edge banding of size 0.45mm on the vertical sides.Hardware made out of steel coated butterfly hinges - 3 Nos.,for each shutter and ISI make SS round lock complete forfinished item of work, complete complying with the standardspecification. The door shutter and frame should be gotapproved from the Executive Engineer before use on work

1000mm x 2100mm

900mm x 2100mm

750mm x 2100mm

Best Indian Teak Wood panelled and glazed door in double shutters with glazed head. The size of frames shall be 100x75mm at ide,verticals,top transom and centre vertical for head. The height of glazed head is 40cm using 595 gm.glass panes for head. The shutters shall be of 40mm thick with moulded panels in 20 mm thick planks for the panelled portion and 595gm. glass panes for the glazed portion. 6Nos.of iron hold fasts fixed in C.C.1:2:4. 6Nos.of butt hinges 125mm long including wind appliances, furniture iron fittings.1No.of iron padlock 15cm long for locking arrangements and fixing in position with 2Nos.of 20mmdia M.S horizontal bars all accesories.

Providing and fixing mild steel grill work for compound wall above brick work. as per drawing Item also including fixtures, fastenings, necessary welding and painting with one coat of anticorrosive paint and two coats of synthetic enamel paint of approved make and shade complete with cleaning.

Structural Glazing: Providing and fixing structural glazing fabricated from roll formed sections made of galvanized steel colour coated (Base steel as per IS 513 of ‘D’ quality, galvanized as per IS 277 with Zinc of 120 grams / sqm.) with total coated thickness of 0.72mm. The glass holding section made of 304 grade SS of 0.6mm thick. Galvanized steel sections are to be used as stiffeners inside the colour coated steel / powder coated sections as per the design requirement. Design calculations are made to suit wind pressures as given in IS 875.Paint specifications: Primer coat with epoxy primer of 5-7, microns thick, finish painted with a polyester paint of 12-16, microns thick and back coated with alkyd backer of 5-7, microns or powder coated with pure polyester powder upto 50-60 microns thick.Dimensions: The section should be of 37 x 53mm for frame vertical, 37 x 53mm for frame horizontal section and section for reinforcement should be of 31 x 55mm. glass holding section should be of 37 x 37mm for top and bottom grids in between should be of 37 x 18mm. Accessories: Brackets made of CRCA powder coated / electro plated should be used to fix vertical at top and bottom and vertical to slab as per site requirement. Polyurethane brackets should be used to connect horizontal section to vertical sections.Silicone: Natural cure, with good UV resistance to be used. The above frame should be fixed to brick / concrete masonry by using nylon self–expanding cap and driving MS electro plated 80mm long screws into the caps through frames.Glass: 5mm reflective Saint Gobain OR equivalent.

Supply and fixing in position of Hot rolled structural steel Members/ Sections consisting of MS joists, channels, angles, purlins, pipes, hollow tubes, runners, insert plates, etc. at all levels. Surface preparation of all MS members by Sand blasting to SA 21/2 grade and painted with anti corrosive, PU paint (metallic finish) with compatible primer to a minimum film thickness of 75 microns and 2 coats of PU paint of and total dry film thickness 225 microns Rate to including all Lifts, wastage, cost of bolts, nuts, washers, welding, electrodes and connections required for the work. No extra on this account will be paid for, and the rate to include preparation of fabrication shop drawings for owner's approval. etc., as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge

Supplying and fixing single skin precoated metal sheet for Roof sheeting at all heights using regular modified polyester (RMP) paint coated 0.50 mm TCT 550 Mpa profiled Galvalume steel (Aluminum zinc alloy coating 150 gms / sqm total of both sides) sheet including cutting, fabricating, erection at all levels, providing openings, touch up painting, all fixtures and fixing accessories such as self drilling, self tapping fasteners, butyl or acrylic sealants, profiled foam / neoprene fillers etc. including cost of all materials, labour, scaffolding, wastage, tools, tackles, equipment, transportation, preparation of shop drawings etc al complete as per specifications drawings and as directed. The Insulation shall be ROCKINSUL Building Rolls of 50mm thick, 48Kg/m3 density in roll forms or as per design requirement composed of basalt Rock fiber bonded together by thermosetting resin with ALG factory laminated facing. The Insulation shall be noncombustible as per EN 13501-1 & BS 476 part 1. The K value - 0.034 W/mK, R value -1.47 m2K/W,U value -0.61W/m2K.The insulation shall be supplied in the form of rolls. The Insulation shall be supported over 50 x 50 mm x 1.6 mm galvanized welded wire mesh. Insulation shall be supported by using 10 G, GI wires tied diagonally with the purlin to avoid sag. Galvalume Colour Sheet of size 0.47mm

Supplying and filling the sunken slab area by BRICK-BATCOBA by adding CICO NO:1 or approved equivalent admixture including applying two coats not less than 2 mm thick of TAPECRETE- Acrylic Polymer Based Waterproof Coating, over the final coat of cement plaster 12 mm thick with cement sand mortar 1:3 mixed with water proofing compound like CICO No.1 at the rate specified in the manufacturer's specification after entire completion of laying pipes, sanitary fittings etc. Rate including all materials, labour charges, wastages with necessary lead and lifts, working at all levels, protecting the laid pipes and sanitary fittings, finishing the surface smooth to receive the top coat of water proofing application etc. as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

i) Including applying two coats not less than 2 mm thick of TAPECRETE- Acrylic Polymer Based Waterproof Coating, over the plastered surface as including final coat of cement plaster 12 mm thick with cement sand mortar 1:3 mixed with approved water proofing compound like CICO No.1 or approved equivalent conforming to IS 2645 at the rate specified by the manufacturer over coated surfacepreparation of surface, finishing, curing etc. all complete at all levels as per manufacturer's specifications and as directed.

TERRACE WATERPROOFING: Supply and laying water proofing treatment for terrace covering the following order and consisting of following operations.

i) Making ' V ' grooves at the construction joints of size 20 x 20 mm and filling the "V" Groove with CICO No. 3 Quick Setting Waterproofing Compound admixed with cement.

The roof slab / gutter slab shall be thoroughly cleaned to remove debris and dust, and applying 2 coats not less than 2 mm of polymer based Elastomeric Coating like TAPECRETE - RTU compound and cured for 7 days and followed by a layer of 20 mm thick cement mortar 1:3 admixed with CICO NO:1 (or) other approved equivalent make shall be spread over the prepared surface.

On the spread mortar provide and lay well burnt brick bats (COBA) to a average minimum thickness of 55 mm (i.e.. minimum 40 mm thickness at lower end and 70 mm thickness at higher end). An additional layer of brick bat (COBA) shall be laid over the existing brick bat COBA surface if required to get the required gradient for adequate drainage giving a slope of approximately 1 in 120,

The gap between brick bat shall be filled with cement mortar 1:4 admixed with waterproofing compound like CICO NO:1 or approved equivalent afterwards curing shall be carried out for two days a final layer of cement mortar of 1:3 admixed with water proofing compound like CICO NO:1 or approved equivalent make shall be laid to a thickness of 20 mm and draw a false line of 300 mm x 300 mm.

The parapet side wall / gutter wall shall be thoroughly cleaned to remove all dust particles and a layer of 15 mm thick C.M 1:3 shall be laid to a height of about 300 mm above the top of the terrace/Gutter slab on the Parapet / Gutter side wall admixed with water proofing compound like the CICO NO:1 or approved equivalent make. Providing, supplying, mixing, applying two coats of ready to use two component Acrylic polymer modified cement based, flexible, water proofing slurry like or approved equivalent to a thickness of 2 mm over the plastered surface of operation as per manufacturer's specification and as directed

Providing and laying water proofing treatment to vertical and surfaces for sunken portion of depressed portions of W.C., and the like consisting of :i) Ist course of applying cement slurry @ 4.4 Kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontalsurface. ii) IInd course of 20mm cement plaster 1:2 (1 cement : 2 coarse sand)mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7Kg. per sqm of area. iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/sqm.)

Supplying And Fixing of Rubber Moulded Grey Premium Concrete Kerb of Size 450X125X300mm Using M30 Concrete. The Concrete Shall Be Moulded By Table Mount Vibrated With Polypropylene Fibers at 5% And Curing Compound. The Rate Shall Include Cost of Materials, Transportation, Loading & Unloading Charges and including Necessary Earth Work Pointing With cm. 1:3 To Full Depth Curing Thread Lining etc., completed as standard specification and as directed by the engineer-in-charge.

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steelpipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mmMS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc.complete

Supplying, fabricating and fixing inposition Aluminium glazed fixed glass partition using 63.50x38.10x2mm @1.127 kg/m Alu.section at 900mm C/C in vertical direction and 1300mm @ C/C at horizontal direction with necessary rubber beadings Alu. clips, of size 17.27x17.15x1.40mm@ 0.175 kg/m and using 4mm thick plain glass including cost of all materilas, labours, power consumptions required for fabrications, drilling holes in RCC column, slab, masonry walls wherever necessary with powerdrills to the required extent and make good to the original condition after fixing and also as directed . All the aluminium sections are to be anodised with matt finish under electrically controlled conditions in accordance with IS 1868/1962.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. ( The make quality and colour of paint should be got approved by the executive Engineer before use on works.)

FALSE CEILING WITH GYPSUM PLAIN TILES Providing and fixing suspended false ceiling providing and fixing GI perimeter channel of size 0.50mm thick having one flange of 20mm and another flange of 30mm and a web of 27mm along with perimeter of ceiling, screw fixed to brickwall / partition with the help of nylon sleeved and screws at 610mm centres. Then suspending GI intermediate channels of size 45mm, 0.9mm thick with two flange of 15mm each from the sofit at 1220mm centres with ceiling angle of width 25mm x 10mm X 0.55mm thick fixed to sofit with GI cleat and steel expansion fasteners. ceiling section 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lops of 10.5mm are then fixed to the intermediate channel with the help of connecting clips and in direction perpendicular to the intermediate channel

Supplying and Installing Metal False Ceiling using Fire Retardant Galvanized Steel Sheet Plain lay in tile size 600mm x 600mm, 0.5mm thick, powder coated on external surfaceand shall have flange on all four sides to rest on the exposed grids. The system to give 600mm x 600mm centre to centre 'T'. The 'T' shall be not be dipped GI Tee Section 3600mm long main Tee. 24mm wide and cross Tee panels are formed by running main runner of 'T' section of size 30mm x 24mm powder coated at bottom at intervals with powder coating at bottom. Necessary provision of inter locking of 'T' section are made at required intervals not exceeding 1200mm. Themain runners are suspended from the ceiling by means of 4mm dia. GI rods fixed to the ceiling using anchor fasteners of 50mm x 8mm size with nylon inset and hooked to the main rubbers using clips. The last hangers at end of each rubber should not be greater than 600mm from the adjacent wall. The last panel shall be placed at the side wall using edge profile 'L' Angle of size 20mm x 20mm and fixed to theside wall the false ceiling should be fixed of same level and should present a neat look

Providing and fixing false ceiling with best Indian T.W.frames tothe size of 100x75mm in length wise and of 50x50mm cross wise andone side T.W.Play with necessary T.W.reepers to the size of 50x12mm and necessary screws etc.,complete as directed

Providing two legged scaffolding using 15 cm dia casuarinas post of 4 M over all length (3 M Height + 0.5 M Projection + 0.5 M into the Ground) the distance between the two rows being 1.25 M and the spacing of posts being 2.0 M in both the rows with two horizontal posts with 0.5 M. Overlap on either side and braces at 2.0 M Center to center including longitudinal and transverse middle braces to step up and providing a platform with country wood planks of 40 mm thick and 1 M width, etc. in a complete from using coil and nails. The rate includes the cost of all materials, labour charges, loading & Unloading and Transportation charges etc., complete and as per the standard specification as directed by the Engineer-in charge.

a)0m to 3m

b)3m to 5.5m

c)5.5m to 8m

d)8m to 10.5m

e)10.5m to 13m

Land Scape

Supply & stacking of red earth at site to the departmental guage for pre-measurements which is of light textured, crystalline, porous and friable and not of generally acidic or neutral but not of alkaline and should be fertile, including seignior age charges, cost of transportation, loading, unloading, stacking and inclusive of all taxes etc., complete.

Planting of Ficus black ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges,transportation, stacking of saplings at site, earthwork excavation of required size, planting ofsapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Nerium oleander dwarf foliage shrub variety of height 30-45 cm in polythene bag of size6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Jasmine Plant foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges,transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Ixora ordinary foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting ofsapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Murraya exotica foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the sitein-charge.

Planting of G2 grass including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Ashoka tree sapling of height 180 - 240 cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Ficus bengalenisis tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking ofsaplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Travellers palm ornamental foliage Specimen plant variety of height 105-120 cm in polythene bag of size 16x16 inch including loading and unloading charges, transportation, stacking o saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Livistona rotundifolia palm variety of height 180-210 cm in polythene bag of size 16x16 inch including supporting stack of 5cm dia casurina pole of 10' height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

PLUMBING

Supplying and fixing the best quality approved make of SS heavy duty long body Tap including cutting and making good walls wherever required etc.complete,complying with standerd specification and as directed by the department officers. The quality and make of angular stop cock should be got approved by concern department engineer before use on work.

Long body Tap

Supplying & fixing in position 15 mm dia brass/ C.P screw down / C.P Pillar Tap (Heavy duty) of approved make conforming to I.S. Specifications & quality including cost of shellac, thread etc., complying with standard specifications & including cutting & threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the work).

15mm dia CP Pillar Tap Garden

Manhole 600 x 600 mm Depth up to 1000mm)

Supplying, laying and jointing CPVC pipes of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using CPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works.

a) 20mm Dia Cpvc Pipes

b) 25mm Dia Cpvc Pipes

c) 32mm Dia Cpvc Pipes

d) 40mm Dia Cpvc Pipes

e) 50mm Dia Cpvc Pipes

Supplying and fixing in position the best quality and variety sizes PVC Soil/ Waste /Rain water pipes 6Kg / cm2 of ISI mark, providing leak proof joints etc and making connection to all sanitary fittings, including dismantling masonry / RCC works wherever necessary and making good the dismantled portions to the original condition complying with standard specification.(Internal,External&Rain water system)

160mm Dia

110mm Dia

75mm Dia

50mm dia

Supplying & fixing in position C.I.Nahini trap /Floor trap of various sizes with best stainless steel gratings of approved brand & quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( One part of lime, two parts of sand & five parts of 40 mm size brick jelly ) & finished with cement mortar 1:3 ( One cement & three sand ) including dismantling masonry works wherever found necessary & making good the damaged portions to the original condition & giving connections to the cast iron pipes as directed etc., complete, complying with standard specification (The C.I.Nahini trap should be got approved by the Executive Engineer before use on works ).

Nahini trap

Supplying & fixing in position 150 X 100 mm square mouth 'P' or 'S' trap stone ware Gully trap 'A' grade with cast iron gratings of size 300 X 300 mm with C.I. air tight cover with frames of size 300 X 300 mm at bottom & top respectively with necessary earth work excavation, laid over a bed of brick jelly cement concrete 1:3:6, 150 mm thick using 20 mm size broken brick jelly including necessary brick work & plastering, &including dismantling masonry wherever necessary & redoing the damaged portions to the original condition & by using cement concrete 1:3:6 using 20 mm stone jelly for fixing the Gully trap & giving connections to the stone ware sewer line etc., complete, complying with standard specification. (The stone ware gully trap should be got approved by the Executive Engineer before use on works ).

Supplying and fixing Lipped Mouth Porcelain Flat Back Urinal(white colour) of size 26.5x31.5x44cm with all accessories such as 32mm dia Bell Mouth PVC Connection, 15mm dia GM Wheel Value, 15mm dia 'B' Class GI Waste Water Pipe, 15mm dia Nylon Connection, 15mm dia Brass Nipple, and suitable screws, shellac etc., complete. The rate including cost of all materials, labour charges for fixing and transportation etc. completed as directed by Engineer-in-Charge.

Supplying and fixing in position Indian water closet of size 580 x 440mm, glazed earthern ware of approved quality and colour with 'P' trap or 'S' trap confirming to IS:2556-part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One of Lime, Two of Sand, Five of Brick jelly) 100mm thick and by dismantling brick masonry, reinforced finishing to the required slope and including giving necessary connection to PVC soil pipes cement concrete roof / floor slab and making good the disturbed portion to origional condition without leakage etc., complete complying with standard specification and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works)

Counter Wash Hand Basin of size 560 mm X 450 mm with all accessories such as cast Iron Brackets, 32 mm Dia C.P. Waste coupling, Rubber plug and Chain, 32 mm dia ' B ' Class G.I. Waste pipe, 15 mm Dia G,M Wheel valve; 15 mm Dia Nylon connection, 15 mm Dia Brass Nipples, 15 mm C.P. Pillar tap etc.,

Pedestal Type Wash Hand Basin of size 550 mm X 400 mm with all accessories such as cast Iron Brackets, 32 mm Dia C.P. Waste coupling, Rubber plug and Chain, 32 mm dia ' B ' Class G.I. Waste pipe, 15 mm Dia G,M Wheel valve; 15 mm Dia Nylon connection, 15 mm Dia Brass Nipples, 15 mm C.P. Pillar tap etc.,

Supply and fixing in position white European Water Closet of approved make with low level flushing tank 6/3 litre capacity of best quality and approved make with 100mm P or S trapwith double flapped rigid PVC seat cover with CP brass hinges etc. complete complying with standard specification and as directed by the Departmental officers (The EWC should be got approved by the Executive Engineer before use on works.

a) Supplying and fixing of CP Wall Mixture Tap 3 in 1 system with Hand Showers including cost of fittings, labour for fixing etc, all complete and as directed by the departmental officers., (The quality of fittings should be got approved from Executive Engineer before use).

Supplying and fixing in position Mirror of size 600x450mm of approved quality and brand with necessary plastic back PVC frame with bottom stand using brass screws rawl plugs for fixing etc complete complying with standard specification and as directed by the Departmental officers. The colour of frame and quality of mirror should be got approved by the Executive Engineer before use on work

mirror 600x450mm.

Supplying,installing,testing and commissioning of approved make CONCEALED STOP COCK for toilet including neccesary accessories etc,complete,works include making require size curout in wall,and fixing the control box property,redoing the same etc,complete the quality and make of concealed stop cock should be got approved by concern department Engineer before use on work.

Conceld stop cock 15mm dia

Supplying,installing,testing and commissioning best quality approved/equivalent make of Single Bowl with drain board 600X600X200 mm stainless steel sink with brass Chromium Plateds wivalty peex tended swing sink cock 32mm dia CP waste coupling, 32mm dia heavy duty waste hose with extension pipe, 15mm CP angle valve with CP inlet connection tube,CP wall flange, including necessary bracket set ccomplete complying with standard specification and as directed by the Department officers.The quality and make o fsink and brass CP coated swiv al type sink cock should be got approved by Concern department Engineer before use on work

600X600X200 mm stainless steel sink

supplying and fixing the best quality approved make of bip cock with C.P health faucet wall hook one metre long fixable tube,angle cock with wall flangle including cutting and making good the walls whewrever requred etc complete, complying with standerd specification and as directed by the department officers. the quality and make of health faucet should be got approved by concern department Engineer before use on work.

Supplying and fixing CP angle cock with wall flange including cutting and making good the walls wherever required etc., complete complying with standard specification and as directed by the Engineer Incharge before use on work.

Supplying and fixing best approved best quality brass CP soap tray of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing approved best quality aluminium anodised towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Part B-WATER SUPPLY SYSTEM ( PIPES & VALVES)

32 mm Dia Upvc Pipe

40 mm Dia Upvc Pipe

50 mm Dia Upvc Pipe

65 mm Dia Upvc Pipe

100 mm Dia Upvc Pipe

Supplying & fixing in position first quality & approved variety of various dia Gun metal Gate valves ( Heavy type ) with I.S.I. Mark of the following size including cost of Shellac, thread etc.,including labour for cutting & threading of Pipes etc., complete complying with standard specifications for both internal & external water supply arrangements.

50 mm Dia

100 mm Dia

Supplying & fixing in position first quality & approved variety of various dia U.P.V.C Ball Valves ( Heavy type ) with I.S.I. Mark of the following size including cost of Shellac, thread etc.,including labour for cutting & threading of Pipes etc., complete complying with standard specifications for both internal & external water supply arrangements.

Internal Toilet Entry & Terrace

b) 25 mm dia

c) 32 mm dia

d) 40 mm dia

e) 50mm dia

supplying and fixing the best quality approved make ofAutomatic Electrical Water Heater with copper container, with Glass Wool / Puf Insulation with MS powder coated shell suitable for 25 Litres capacity 230V / 1000W (Higher End) fixable tube,angle cock with wall flangle including cutting and making good the walls whewrever requred etc complete, complying with standerd specification and as directed by the department officers. the quality and make of health faucet should be got approved by concern department Engineer before use on work.

Supply, erection, testing and commissioning of Gun Metal Non-Return Valve of size 50mm dia including necessary MS flange of table’E’, gaskets, bolts & nuts, etc., installed at pump house delivery line for the purpose of priming to suction line so that to control one way including conveying, fixing and incidental charges etc., complete as per standard specification and as directed by the Departmental Officers.

a) 50mm dia - as per quote

a) 65mm dia - as per quote

Providing, laying, jointing and testing socketed and spigotted RCC pipes (NP3 class) conforming to IS:458 collars jointed with stiff mixture of cement mortar in the proporation of 1:2 (1 cement : 2 find sand) laid to correct levels below ground in trenches upto required depth including excavation in all kind of soil (hard / soft), dewatering, refilling, watering, ramming and removing the surplus excavated material and making good the same complete as required. (the Hume pipe sholud be got approved by the Executive Engineer before use on works

150 mm Dia

300 mm Dia

Supplying and fixing PVC moulded CI Steps for access way including anchorage in walls to a minimum depth of 100 mm with C.C 1:2:4 (one cement,two fine aggregate and four coarse aggregate) etc.( Duct ,Shafts & UG sump,Over Head Tank and wherever necessary) Note: Rungs to be fixed before concreting and necessary provision to be made in the shuttering.etc complete, as directed by the Engineer-in-charge.

Supplying and fixing in position best quality of HDPE pipes with ISI mark of following dia with specials including cost and coveyance of HDPE pipes and specials, labour charges for erection of pipes in the borewell and jointing materials etc., all complete as directed by the departmental officers.

50 mm Dia HDPE Pipe

UG Sump&Over Head Tank Cover

Manhole Cover Size 600x600 mm Manhole Cover With Frame 5 Ton - Double Cover

Providing and keeping in stores, shifting to the place of installation, fixing of 1mtr length, 6mm Thickness MS Puddle flange UG Tank & OHT Puddle flage

65mm MS Puddle Flange

50mm MS Puddle Flange

40mm MS Puddle Flange

UG SUMP TO OHT

Supply, erection testing and commissioning of electric driven Dewatering pump,The pump is with cast iron casing high efficiency with bronze impeller with supply conditions 400v 3 phase 50 Hz with all accessories like standard coupling guard, common base plate,foundation bolts and connected civil works. 1 Discharge of 2Lps with 2 horse power motor with total head of 10-15 MWC

Supplying , Installing, Testing and Commisioning of water meter conforming to IS 779 :1994 (Reaffirmed 2009) of approved make with necessary tapers, valves, strainers, speicals, nuts, bolts and washers etc all complete including applying one coat of red oxide paint and two coats of enamel paint of specified colour.The water meter shall be analog.

BORE WELLS

Drilling of 12" dia vertical borewell so as to have a finished size of 6" dia borewell in boulder area to any required depth as decided by the including Transportation from one place to anothr place with in Tamilnadu State by direct or reverse rotary mud circulation method using Contractor's rig tools, fuel, labourers, bentonite mud and water required for drilling at the site shown by the including construction of mud pit etc.

Reaming from 200mm dia pilot bore to 350mm dia bore as direct by the Engineer incharge up to 80mtr depth ending below ground level

Supply and laying following dia PVC casing pipe with excise duty as per IS 12818 / 1992

200mm dia CS ( plain pipe )

200mm dia RS

150mm dia RS

Labour charges for inserting PVC casing pipes assembly (with slots or without slots) in the drilled hole including jointing the pipes with PVC couplers with cement paste etc., complete, supply and packing the annular space with pebbles of size and quality as approved by the Executive Engineer of Departmental officers.

200mm dia CS

200mm dia RS

150mm dia RS

Supplying and filling with river pebbles in annular space between bore and PVC pipe up to hard rock.

Charges for developing the borewell with air compressor of 300 CFM capacity (Minimum 8 Hours) including transportation labour and fuel charges for compressor as directed by and conducting yield test by 'V' notch method.

Supply ,erection and testing & commisioning of 3HP submersible pumpset in the to suit 200mm borewell of capacity of 4800 LPH @ 265Ft, max. total head of 280 Ft pumps fitted with bronze impellers and having delivery size of 40mm - 430V along with 3mts cable and manufactures standard control panel which is mandatory and as directed by the officer incharge and other required supporting items like SS hose nipple, nylon rope, clamps, bolt and nuts,GI nipple, 50mm dia HDPE hose of required length etc completed and as directed by the officer incharge.

Supply and delivery of submersible centrifugal sewagenon-clogpumps, vertical spindle type pump, wear resistance with submersible motor for the variousduty conditions. Pump shall be capable of handling min 100mm solid sizewith sewage specificgravity of upto 1.05. Pump shall be of robust construction, Liquid passagess hall be finished smooth and designed as to allow freepassage to solids. PumpImpeller shouldbe of Non-clogsemiopen type, singlevane / multivanepreferably contrablocorvort eximpeller design. Double mechanical seal with silicon carbide facess hould be provided toprotect the motor fromingress of sewagealong the shaft. The critical speed of the rotor shall be at least 30% above theoperating speed. Pumps should have double berings between thepump &motor. The bearings life shall be minimum 100,000 hrs of operation with greased for life. Pump should be provided with automaticcoupling device including pedestal, duckfootbend, stainless steel guide pipe or related accessories of suitable size to facilitate lifting and lowe ringin to guiderails for easy maintenance. Pump shall be provided with a stainlesssteel lifting chain conforming to BS970 Gr 304. Pumpspeeds hall be of 9600 rpm for high duty pumps and 960/1450rpm for lowduty pumpsets. Casing and impeller should be of CI Gr.FG260:IS210 more preferably with hardenedimpeller. Shaftshould be of stain lesssteel AISI410. All the fasteners and bolts shall be of AISI410. The submersible motor shall be operated with 3ph, 415V (+or–10%), 50Hz (+or-5%) dry induction type. Motor shall be capable of giving rated out put without reduction in the expected lifespan whe no perated continuously. Therotating assembly shall be dynamically balanced as per standards. The starting current of the motor shall not exceed 200% of rated full load current for Star / Deltaor ATS starting under any circumstances. The motor shall be suitable for full voltage star delta/ATS starting. The locked rotor current of the motor shall not exceed 600 % of full load current unless otherwise specified. Motor shall be designed to withstand 120% of rated speed for two minutes with out any mechanical damage, in either direction of rotation. The motor vibration shall be within the limit specified in applicable standards. Motor should be of IE2, explosionproof compatible for VFD operation to gether with star-Delta/ATS starter, protectionagainst increase in stat or winding temperature (15deg Celsius), bearing temperature, leakage in the statorhousing and terminal box shall be provided and to be suitably interlocked with the control panel for tripping the pump in case of increase in temperature beyond set limit. Insulation classsh all be of“ ClassH” and degreeof protection shall be of IP68 asper IS4691. Motor shall be suitable for continuous operation in fully submergedorpartially submerged condition. The pump set shall be supplied with power cable of PVC insulatedand PVC sheathed, copper, flexible, round type with required conductor size and number of cores as per starting method and of specified length for continuoususe under water and air. The control cable of PVC insulated, PVC sheathed, flexible for stat or winding temperature sensor 3 corex1.5sq.mm copper conductor and for bimetallic switches 2corex1.5sqmm copper conductor shall be provided. Motor shall be supplied with 10 mofround submersible copper cable of suitable size up to 10 Mtr to 15 Mtr Head and Discharge Upto 20 M3/hour

Construction of Modular type RWH Structure capacity of 4.32 cu.m by using infiltration modules of size 800 x 800 x 360 mm and side wall with infiltration modules of size 800 x 360 x 25 mm including earthwork excavation in bitumen/concrete roads to a size of 1200 x 1200 x 3000 mm and providing base plate, Geo - textile 400mm - 200 micron, Fine filter media 12mm thickness, Coarse filter media 20mm thickness, FRP of 700x700mm (clear opening 600x600mm) (Grating cover with Frame - Medium duty 10 MT). including all labour charges, carting away and drilling bore well 150mm dia upto a depth of 3m with 125mm dia Blue slotted PVC Pipe., complete.

Fire Fighting

Supply, erection, testing and commissioning Mono BloSupply, erection, testing and commissioning of fire fighting application monoblock motor pumpset of 450 LPM at 20 metres head to develop 2.0 kg/sq.cm at the heightest and farthest hydrant point to make 10m water jet at the time of fire fighting emergency cicumstances, coupled with 3.75KW / 5HP rated three phase 415 volts, 50 Hz, 2880 rpm electrical motor, the pump with cast ron body, bronze impeller, rope gland packaging, suction size of 80 mm dia. delivery size of 65 mm dia, including the cost of foundaton concrete anti vibration mounting, rain safety hood and etc. complete as directed by the Departmental Officers (Kirloskar make KDS 538 or Equivalent))ck type Fire Fighting Pressurisation Pump of 180 LPM 110 metres head at 10 HP with suitable base frame including necessary vibration bad mounting etc., including conveying, fixing and incidental charges., etc., complete as per standard specification and as directed by the Departmental Officers.

Supply and laying of 4 core 10 sq.mm. armoured copper cable for power wiring to the Terrace Pump Motor with runs of 14 SWG TC wire for earthing, providing in wall with suitable size GI clamps, screws, wooden plug, end termination by using suitable size cable glands, copper sockets and etc., as directed by the Departmental Officers.

Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table ‘E’, elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL / EQUIVALENT.

150mm dia M- 0798

100mm dia M- 0799

80mm dia M-800

Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table “E”, bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers.

Supply, and fixing in position of Fire Fighting Application Hose of 63mm dia of 15 metres length binded by copper wire with 63mm dia stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the Departmental Officers. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers.

Supply, and fixing in position of Fire Fighting Application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzle of 15mm (or) 20mm jet bore. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.

Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary., etc., complete as per standard specification and as directed by the Departmental Officers.

Supply and fixing in position of Fire Fighting Duct Window having proper glass window type double door with universe open key, painted inside white and outsid post office red for the sizes of 1300 x 900 x 500mm (L x B x D) fabricated using 25 x 3mm MS 'L' Angle and all sides covered with 2mm thick MS sheets, suitable arrangements to kept 2 Nos. of Fire Fighting Hoses and 1 No. Branch Pipe, mounted in fire duct using anchor fasteners, etc., as per standard specifications and as per directed by the Departmental Officers.

Supply, erection, testing and commissioning of cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary MS flange of table ‘E’, gaskets, bolts & nuts including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.

Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14 kg. range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers.

Supply and fixing of Carbon-di-Oxide Gas Type 2 kg. capacity Fire Extinguisher as per New IS15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc., complete as per standard specification and as directed by the Departmental Officers.

SSupply and kept in position of Trolley Mounted Type 22.5 kg. Carbon-di-Oxide Fire Extinguisher as per IS15683, complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, mounting trolley with moving wheel, safety clip, etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.

ELECTRICAL

HT WORKS

HT RMG Panel - Supply, Installation, Testing and Commissioning of11 KV, 25 KA, 630 A, HT Outdoor Three Panel Ring Main Gear "11kV HT Outdoor RMG Panel Supply,Installation,Testing and Commissioning of OUTDOOR Weather & Dust proof Type, floor mounting, free standing type 11KV Ring Main Gear unit made out of M.S sheet steel clad dust and vermin proof with 630A Copper Busbars, Interconnections, necessary protections, Measuring Instruments, Indicating Instruments, necessary Protection Relays, CTs, PT with necessary control fuses/MCBs, Termination arrangements for Incoming and Outgoing Cable of as per EB authorities approval ,earthed cable, Terminal Blocks, Earthing, Powder coated painting, Sign writing and Base channels etc., with complete all accessories as required for satisfactory operations and as per the detailed Technical Specifications enclosed and as per TANGEDCO Requirements comprising of the following. Remote Communication and operation (1) 11 KV, 630 A, 25 KA Horizontal Draw out, vertical / horizontal Isolation 1 No. VCB fitted with manual / Motor operated spring charging Mechanism with 230 V AC, shunt trip coil of 110 V DC, closing coil of 110 V DC, Auxiliary Contact 8 NO + 8 NC, Mechanical ON / OFF indicator, mechanical operation counter, Automatic safety shutters, Push button and breaker position indicator including epoxy insulator - 1 set

Supply, Laying of 185 sq.mm. 3 core HT XLPE 11KV UG cable with necessary aluminium cable sockets by crimping with electrical connection complete.

Supply, Termination of 120-185 sq.mm. 3 core HT Cable Indoor Terminations XLPE 11KV (E) - EPKT 3111 cable with necessary connection complete.

Supply and Clamping of 31/2C x 400 Sq.mm PVC armoured LTUG aluminium cable on post or on wall with MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and laying of 3 1/2C x 400 Sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and fixing of brass cable gland for 3-1/2 x 400 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 31/2C x 400sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping with electrical connection complete.

Earthing as per PWD standard with an earth electrode of 2meter Class 'B' GI pipe of dia not less than 32mm complete with necessary masonary work

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI Pipe of dia not less than 40mm, with copper earth plate of size 600mm x 600mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and run of 50mm x 6mm Aluminium flat with necessary clamps / supports on wall / floor / ground for earth connection and etc to complete the work.

Supply and run of 50mm x 6 mm Cu flat with necessary clamps / supports on wall / floor / ground for earth connection and etc to complete the work.

FENCING YARD: OUTDOOR Fencing yard for outdoor 11kV HT Panel, Transformer area. (Plan Area) Supply and laying of Fencing details of height of 2.1 mtr with chain link mesh made of 10 SWG GI wire with mesh size of 50mm x 50mm welded to angle iron frame made of 50mm x 50mm X 5 mm size on all four sides and 1 no. horizontal intermediate member of 50mm x 50mm x 5mm welded to 25mm x 5mm flat to form 'T' section (The angle iron frame shall be fabricated in section of width not more than 1.5 mtr and assembled at site to form the required fencing). The vertical members of frame shall be extended by 75cm for erection in ground, including erections of the angle iron frames in 1:3:6 cement concrete.

PANEL

Fabrication, Supply, Erection, Testing and Commissioning of whether proof CRCA sheet steel powder coated Indoor panel board, made up of 2 mm powder coated, including bus bar provision of double door with industrial lock with main 250A,TPN MCCB I/C and 2nos 32A TP MCCB & 6Nos 63A TPN MCCB for O/G with suitable copper bus bar (25x6mm) having three phase Digital volt and ammeter with line indicators for erecting the Indoor panel board suitable for mounting on wall surface with internal wiring and earth connections. The above panel board is to be erected with anchor fastner, bolt and nut or suitable angle etc.

Fabrication, Supply, Erection, Testing and Commissioning of whether proof CRCA sheet steel powder coated Indoor panel board, made up of 2 mm powder coated, including bus bar provision of double door with industrial lock with main 160A,TPN MCCB I/C and 4nos 32A TP MCCB & 4Nos 63A TPN MCCB for O/G with suitable copper bus bar (25x6mm) having three phase Digital volt and ammeter with line indicators for erecting the Indoor panel board suitable for mounting on wall surface with internal wiring and earth connections. The above panel board is to be erected with anchor fastner, bolt and nut or suitable angle etc.,

Fabrication, Supply, Erection, Testing and Commissioning of whether proof CRCA sheet steel powder coated Indoor panel board, made up of 2 mm powder coated, including bus bar provision of double door with industrial lock with main 160A,TPN MCCB I/C and 8Nos 63A TPN MCCB for O/G with rotary handle , suitable copper bus bar (25x3mm) having three phase Digital volt and ammeter with line indicators for erecting the Indoor panel board suitable for mounting on wall surface with internal wiring and earth connections. The above panel board is to be erected with anchor fastner, bolt and nut or suitable angle etc.,

Supplying, erecting, testing and commissioning of machine room less passenger Elevator having 20 passengers capacity, rated speed 1.0 mtr. / sec., for Basement, GF, 1st & 2nd floor, 400 volt 3 phase, 50 Hz, AC variable voltage variable frequency derive with speed encoding, simplex full collective with / with out attendant, microprocessor based controller located top floor, variable frequency regenerative drive, flat polyurethane coated belts for traction media, stainless steel panels with hairline finish for car and door, gearless with permanent magnet motor located in the shaft top, all openings are located at the front of the hoist way, with centre opening Automatic with ACVVVF door operator with electronic door protective system, stainless steel hairline finish sliding doors, painted frame with down light false ceiling, Stainless Steel mirror finish hand rails, granite flooring of client choice, sixteen segment digital LED display position indicator in all floors, digital car position indicator, over load warning indicator, battery operated alarm bell and emergency light, fireman's switch at main lobby, with automatic rescue device, intercom between lift car and lobby and controller, voice synthesizer, 60 minutes fire rated car door. Car Entrance.

Supplying, erecting, testing and commissioning of machine room less passenger Elevator having 20 passengers capacity, rated speed 1.0 mtr. / sec., for Basement, GF, 400 volt 3 phase, 50 Hz, AC variable voltage variable frequency derive with speed encoding, simplex full collective with / with out attendant, microprocessor based controller located top floor, variable frequency regenerative drive, flat polyurethane coated belts for traction media, stainless steel panels with hairline finish for car and door, gearless with permanent magnet motor located in the shaft top, all openings are located at the front of the hoist way, with centre opening Automatic with ACVVVF door operator with electronic door protective system, stainless steel hairline finish sliding doors, painted frame with down light false ceiling, Stainless Steel mirror finish hand rails, granite flooring of client choice, sixteen segment digital LED display position indicator in all floors, digital car position indicator, over load warning indicator, battery operated alarm bell and emergency light, fireman's switch at main lobby, with automatic rescue device, intercom between lift car and lobby and controller, voice synthesizer, 60 minutes fire rated car door. Car Entrance :- Clear opening

DISTRIBUTION BOARDS & MCB

Supply and fixing of 7 segment 4 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 4 ways in each segment) and seperate provision for MCB / Isolators ( totally 12 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only.

Supply and fixing of 7 segment 4 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 4 ways in each segment) and seperate provision for MCB / Isolators ( totally 12 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only

Supply and fixing of 7 segment 8 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 4 ways in each segment) and seperate provision for MCB / Isolators ( totally 12 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 40A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only.

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB Isolator as incoming and 6 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only.

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 40A FP MCB Isolator as incoming and 1 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End ( Like Standard make ) Lift DB

Supply, Erection, Testing and Commissioning of the following Type outdoor lighting distribution panel with individual segegration chamber with MCCBs / MCBs /ELCBs, / RCCBs , Phase segegration Timer and contactor manufacturer's sheet 16SWG enclosure for with provision for cable entry boxes, with Outdoor application IP65 as specified Protection, fixed on the floor with all interconnections and accessories, pedestal frame with concrete grouting or suitable to fix at concrete plinth as per the Corporation/ Highway department requirement. Incomer 40 A TPN MCB with Timer control On/OFF Outgoing : 20 A DP RCCB -30mA - 18 Nos

Lift Shaft Wiring : Wiring, Connecting, Testing & Commissioning for lift well light point and 6Amps power socket outlet with 2 x 2.5 sqmm FRLS PVC insulated stranded copper conductor of 1100V grade along with 1 x 2.5 sqmm FRLS PVC insulated standed copper conductor cable as earth wire in MS conduit including providing and fixing switch box, 2 Nos. of 5A single way module switch (for controlling light point and socket Outlet ) for each floor of the lift well , with bulkhead lamp 1 No. 5A 5 Pin shuttered socket outlet with flush type switch for each floor of the lift well and making necessary connections complete etc.

CABLES

Supply and Laying of 31/2C x 120 Sq.mm PVC armoured LTUG aluminium cable in existing trench, hume pipe, tray etc, The Rates complete including transport charges of UG cable.

Supply and Laying of 31/2C x 95 Sq.mm PVC armoured LTUG aluminium cable in existing trench, hume pipe, tray etc, The Rates complete including transport charges of UG cable.

Supply and Laying of 31/2C x 70 Sq.mm PVC armoured LTUG aluminium cable in existing trench, hume pipe, tray etc, The Rates complete including transport charges of UG cable.

Supply and Laying of 31/2C x 35 Sq.mm PVC armoured LTUG aluminium cable in existing trench, hume pipe, tray etc, The Rates complete including transport charges of UG cable.

Supply and Laying of 31/2C x 25 Sq.mm PVC armoured LTUG aluminium cable in existing trench, hume pipe, tray etc, The Rates complete including transport charges of UG cable.

Supply and Laying of 4 x 10 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

GLANDS

Supply and fixing of brass cable gland for 31/2C x 120 Sq.mm PVC LTUG armoured cable with earth connection

Supply and fixing of brass cable gland for 31/2C x 95 Sq.mm PVC LTUG armoured cable with earth connection

Supply and fixing of brass cable gland for 3-1/2 x 70 sq.mm. PVC armoured LTUG cable with earth connection

Supply and fixing of brass cable gland for 31/2C x 35 Sq.mm PVC LTUG armoured cable with earth connection

Supply and fixing of brass cable gland for 31/2C x 25 Sq.mm PVC LTUG armoured cable with earth connection

Supply and fixing of brass cable gland for 4C x 10 Sq.mm PVC LTUG armoured cable with earth connection

END TERMINATION

Supply and providing cable end termination of 31/2C x 120sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping with electrical connection complete.

Supply and providing cable end termination of 31/2C x 95sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping with electrical connection complete.

Supply and providing cable end termination of 31/2C x 70sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping with electrical connection complete

Supply and providing cable end termination of 31/2C x 35sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping with electrical connection complete.

Supply and providing cable end termination of 31/2C x 25sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping with electrical connection complete.

Supply and providing cable end termination of 4C x 10sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping with electrical connection complete.

WIRING

Wiring, testing and commissioning of 2Rx1.5sqmm (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe with 2 mm thick, ISI marked concealed in wall and ceiling with PVC accessories with Module GI Switch Box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection by 2.5sq.mm PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light / Fan Point (for electronic) (Primary Point)

Wiring, testing and commissioning of 2Rx1.5sqmm (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe with 2 mm thick, ISI marked concealed in wall and ceiling with PVC accessories with Module GI Switch Box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection by 2.5sq.mm PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light / Fan Point (for electronic) (Secondary Point)

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe concealed in wall and ceiling with MS accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with continuous earth wire connection of 14 SWG TC wire forand making good of the concealed portion with painting of suitable colour for conceale MS conduit Light point / fan point (for electronic regulator) (4 points / Coil) Higher End( MS Point wirng Primary)

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe concealed in wall and ceiling with MS accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with continuous earth wire connection of 14 SWG TC wire forand making good of the concealed portion with painting of suitable colour for conceale MS conduit Light point / fan point (for electronic regulator) (4 points / Coil) Higher End( MS Point wirng Primary)

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe concealed in wall and ceiling with MS accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with continuous earth wire connection of 14 SWG TC wire forand making good of the concealed portion with painting of suitable colour for conceale MS conduit Light point / fan point (for electronic regulator) (4 points / Coil) Higher End secondary point-With Out Switch

CIRCUIT MAINS

Supply and run of 2 of 2.5 sqmm (36/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection 1 of 2.5 sqmm (36 /0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade and making good of the concealed portion with suitable colour.

Supply and run of 2 of 4 sqmm (56/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe concealed wall and ceiling with continuous earth wire connection 1 of 2.5 sqmm (36 /0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade and making good of the concealed portion with suitable colour.

SWITCHES & SOCKETS

Supply and fixing of 1 no.6A two module 5Pin socket , 1 no. 6A one module switch with modular cover Plate (Plastic) on suitable module concealed Box ( GI ) in flush with wall with connections.

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with modular cover Plate (Plastic) on suitable module concealed Box (GI ) in flush with wall with connections.

Supply and fixing of 1 no 25A Flush type Wall Socket with 25A DP MCB for AC Plug .AC socket

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with modular cover Plate (Plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End ( SD-488) 20 A Geyser socket all higher end

Supply and fixing of AC / DC 76mm buzzer / call bell suitable for 230 volts 50 c/s single phase AC supply on suitable TW board with push switch call bell on suitable module concealed Box (GI ) in flush with wall with connections.

LIGHT FITTINGS

Supply and fixing of 20W, 4FT LED fitting with LED on wall or ceiling with PVC unsheathed copper leads from terminals to the fitting and to complete necessary accessories and etc to complete the work.

Supply and fixing of 18W LED 3000 K round type recessed light on wall or ceiling with PVC unsheathed copper leads from terminals to the fitting and to complete necessary accessories and etc to complete the work

Supply and fixing of 18W LED 2 ft mirror light on wall with PVC unsheathed copper leads from terminals to the fitting and to complete necessary accessories and etc to complete the work.

Supply and fixing of 24W, 4000K Type Square type recessed fitting with LED Down light on wall or ceiling with PVC unsheathed copper leads from terminals to the fitting and to complete necessary accessories and etc to complete the work.

Supply and fixing of 18W, 3000K Decorative Pendent type fitting with LED Down light on wall or ceiling with PVC unsheathed copper leads from terminals to the fitting and to complete necessary accessories and etc to complete the work.

Supply, installation, testing and commissioning of 200 W LED Round High Bay Light fitting in PDC Housing suitable for Ceiling / roof sheet mounting, The luminaire has efficacy of 125 lm/w .ITt has 10KV SPD & IP 66 additional safety chain with made out CRCA powder coated body and including electronic drivers, day light colour LED lamps, inter connecting wiring with suitable fixing clams, hooks as required including accessories all inclusive (Cat. Ref. Philips Make: BY617P LED300S 5700 NB PSU GR or Equalant)

Supply, installation, testing and commissioning of 100 W LED Round High Bay Light fitting in PDC Housing suitable for Ceiling / roof sheet mounting, The luminaire has efficacy of 125 lm/w .ITt has 10KV SPD & IP 66 additional safety chain with made out CRCA powder coated body and including electronic drivers, day light colour LED lamps, inter connecting wiring with suitable fixing clams, hooks as required including accessories all inclusive (Cat. Ref. Philips Make BY615P LED150S 5700 WB PSU GR or Equalant)

Supply and fixing of LED Flood Light 150W with Integrated Driver Superior finish etc., complete. The rate inclusive of all taxes and transportation charges etc.

Supply and fixing of 10W Bulk Head LED Fitting with Surface mounted LED luminarie Superior finish etc., complete. The rate inclusive of all taxes and transportation charges etc., complete ( Cat. Ref. Philips Make; WT202W LED10S or Equalent).

Supply and fixing of 1 Set of Cove Light 24W RGB LED Strip light (5 Mtr Length) in false Ceiling with LED Driver complete accessories. The rate inclusive of all taxes and transportation charges etc.

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18")

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall

Supply and fixing of 1500W automatic electric water heater of 35 litres capacity suitable for 230V 50 c/s AC supply on suitable MS clamps with 3 core flex wire but without plumbing connection

Supply and fixing of 300mm(12")sweep (Heavy duty) AC Exhaust fan complete with necessary wall opening and making good of the wall and wiring to the near by point with 1.5 sqmm FRLS PVC insulated copper wires including necessary accessories and hardware's as required.

supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED street light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED steet light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour.

EARTHING

Supply and Instalatin for 7.5 KVA UPS with Battery, Single Phase UPS (Three Phase In & Single Phase Out) Capacity - System with Battery - 1 Hours back up

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection and etc to complete the work

Supply and run of 25mm x 6.25mm Aluminium flat with necessary clamps / supports on wall / floor / ground for earth connection and etc to complete the work.

Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8SWG GI wire at the equal interval of 1.5 meter and etc to complete the work.

Coil Earth to Street light poles with No 8 SWG GI wire of 11.5 Mtrs of length in which 10 mtrs of total length compressed in to a coil of one meter length (75 mm to 100 mm dia) connected suitable with Hexagonel earth bolt of size 8mm to 25 mm welded on the pole at one end with a coil position fixed on the earth and etc to complete the work

LIGHTING ROD Supply of Early Streamer Emission Air Terminal (ESEAT). Model: L The ESEAT has corrosion resistant stainless chrome body made up of AISI 316 grade of height 0.50 metres capable of working in hazardous atmosphere. The Air terminal is non-radioactive and requires no special licensing. The unit is fully autonomous (no battery, no external power supply is required), collects energy from the ambient electric field. The ESEAT model has been tested in a high voltage laboratory in accordance with NFC 17 102 in order to measure the average gain in triggering. The average gain in triggering time (ΔTs) obtained during the lab test for the offered model is 60 μs. The ESEAT works on negative as well as positively polarized discharges. ESEAT has been tested for such discharges in Central Power Research Institute (CPRI). A dedicated tester is available to test the healthiness of the ESEAT on request (Page No. 37, Point No. 3 of Clause 8.6 of the Revised NFC 17-102 version 2011 ). ESEAT Model : L - Radius of protection : 86 Metres Level of protection considered for the Project-II level

MOUNTING STRUCTURE Supply of Standard / Special Mounting Structure of height 4.5 mts. pipe, and 300 x 300 x 8mm MS plate, 3 mts. 48mm OD class C GI outer pipe,1.8 mtr, 38mm OD inner pipe, for roof mounting on concrete base and with FRP adapter

TEST LINK Supply of Test Link Box for each Down conductor in order to disconnect the earth termination system to enable measurement of resistance

EARTH ELECTRORODE Supply and installation maintenance free GI Earthing System comprising of 50mm dia and 2 mtr. long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs. of carbon based environment friendly backfill compound and suitable clamp

DOWN CONDUCTOR Supply and run of 25mm x 6mm GI Flat Down Condutor with necessary clamps / supports on wall / floor / ground for earth connection.

SURGE PROTECTION Supply and installation Cabinet Type Class 1 and 2 Combined Model SPD to arrest surges and overvoltages in the power line due to lightning switching action etc. they must be installed in the incoming MCC panel / DB of the respective building in parallel to the power circuit. Model: PSV4-12.5/400TT (3 phase power network)

CABLE TRAY

The cable rack shall have runners rugs of suitable size, horizontal elbow, vertical elbow 90 Deg. Up vertical elbow 90 Deg. Down, re-deep, coupler plates, materials. The cable racks shall be suspended from ceiling supported from side walls in columns etc. with adequate size supporting angles / channels with fastners, welding, anchor bolts, nuts etc. The rack shall have suitable cable clamping arrangements etc.' Cable Tray /ladder should be powder quoted as match with ceiling colour as per PWD requirements. The rate shall inclusive of necessary Wedge anchors theaded rods,nuts & bolts, making clamp for rcc roof fix / perlin/Truss, cable tray clamps etc,(8 mm threaded rod supports shall be provided at not more than 2 mtr center to center and as per site requirement)

Supply and Laying of GI Hot Dip / Powder Coated 16 SWG Cable Tray with 150mm width and 50mm height.

Supply and Laying of GI Hot Dip / Powder Coated 16 SWG Cable Tray with 300mm width and 50mm height

Supplying and fabricating of MS structural steel supports of size 450mm x 150mm for various applications using U channels, MS angle iron, bolts, nuts, anchor bolts etc., required for the work, cut to the size, bent to shape, welding, grouting etc., complete. Supports shall be powder coated with required colour for different system as mentioned above.

First Aid Box complete with all First Aid Medicines

Shock Treatment Chart fixed in glass frame

Fire Extinguisher Co2, 4.5 kg. confirming to TAC Norms

Danger Board as required by the Electrical Authorities

2m x 1m Rubber Mat suitable for 11 KV installation confirming to IS (M-1976) (5 set)

Hand Gloves 11KV Grade M-1980

Earth Discharge Rod M-1983

Supply and kept in position of 9 litres capacity Fire Buckets of 4 Nos. with Bucket Stand as per standard specifications and as directed by the Departmental Officers

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers.

Supply and fixing of CO2 Gas Type 2 kg. capacity Fire Extinguisher as per New IS15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc., complete as per standard specification and as directed by the Incharge.

Supply,Installation, testing and commissioning of VRV/VRF Indoor air conditioning units with direct driven fan, high efficient filter, inbuilt microprocessor thermostat, electronic expansion valve, provision of fresh air duct connection, wired PID remote controller, drain pump, necessary ceiling supports & vibration isolators, refrigerant charging, oil charging,Refnet joints, control wiring and drain connection, etc. The fan power consumption of VRF Indoor units should Not exceed 0.0006 bhp/cfm for ductable units and 0.0004 bhp/cfm for cassette units as per specification. The capacities are as mentioned below:-

Supply of High static Air Conditioning Unit with evaporator, blower and outdoor unit comprising of scroll compressormodel VRF & Fan.Air conditioning unit suitable refrigerent R410 A, wired Thermostat.

Ductable Unit

Capacity: 14 HP -M-2032

Capacity: 14 HP -M-2032

Supply, installation, testing & commissioning of Double skin construction draw thru type ceiling suspended AIR HANDLING UNITS with Electronic expansion kit with 25 mm thick Sandwitched PUF insulation panel as per specification & as indicated in the Equipment Schedule. Each complete with DIDW Forward Curved Centrifugal Fan , filter sections, DX coil of copper tube & Hydrophillic (Blue) coated aluminium fins. The fan motor should squirrel cage induction motor, centrifugal fan direct driven / Belt-driven with spring type vibration isolators, Limit switches,Emergency Light, Guard for inspection door, Prefilter (MERV8) & bag filter (MERV 13), drive sets, SS insulated drain pan etc., Motor shall be suitable for 220/415 volts, 50 Hz, 1/3 Ph AC supply.

Supply and Installation of Air Conditioning Unit with evaporator, blower and outdoor unit comprising of scroll compressor & Fan.Air conditioning unit suitable refrigerent R410 A With wired Thermostat(remote) and out unit MS Mounting bracket/Channel as per unit size.

Supply and installation of of Hard drawn Refrigerant copper piping, fittings with suitable closed cell nitrile rubber insulation covering with FRP tape as a resistant to Scratch & Mechanical Impact. The pipe sizes and insulation thickness as follows.

Gas line 1 1/8" copper with 28.60 mm thick insulation M-2049

Liquid line 5/8" copper pipe with 15.90mm thick insulation M- 2052

Supply and providing of pipeline nitrle rubber insulation for Refrigerant and drain pipe lines. M- 2013

Supply and laying of cabling between indoor and outdoor units. The rate shall be including suitable size Heavy duty PVC conduit with conduit accessories and necessary fixing arrangement.

6core X 2.5sqmm copper armoured cable (indoor unit to Outdoor unit)

Supply and erection of the following Heavy Duty PVC Drain pipe with all joints, reducer, necessary elbows and tees, supporting arrangements and Nitrile rubber insulation with 9mm thickness etc.

32 mm dia M-2010

Supply and providing of pipeline nitrle rubber insulation for Refrigerant and drain pipe lines

Supply, installation, testing and balancing of Air Distribution System consists of factory fabricated sheet metal ducting complete with supports (anchor fasteners and tie-rods, cradles, angle iron supports, GI bolts and nuts, 4mm thick self-adhesive neoprene rubber gasket, stiffeners, zinc chromate painted angle iron flanges, chipping and plastering of openings made for duct supports etc., complete as per specification. The rates quoted shall include turning vanes, straightening vanes, splitters, inspection doors probe, inlets with test openings enclosures complete with locking caps, chain, gaskets, Gripple/OBO make wire ropes etc.

24G GSS ducting

22G GSS ducting

Supply and providing acoustic for initial portion of ducting with 12mm thick Fibre Glass Rigid Board covered with Tissue Paper and Aluminum Perforated Sheet.

12mm thick

Supply and providing thermal insulation of 9mm thick vidoflex with Aluminum Foil.

9mm thick

Supply and fixing of extruded aluminum powder coated, Supply and return Air Grilles / Diffusers with Volume Control Damper

Supply and installation of Fire Retardant Canvass connections with GI matching flanges on both sides with a provision of openable zip. The entire assembly shall be factory fabricated.

Design, Supply and erection of steel supports like MS plate, angles, channels, etc. Rate shall inclusive of cutting, welding, grinding, fixing accessories and one coat of primer & one coats of enamel paints, etc. as required for Outdoor unit M- 2012

Design, Supply and erection of steel supports like MS plate, angles, channels, etc. Rate shall inclusive of cutting, welding, grinding, fixing accessories and one coat of primer & one coats of enamel paints, etc. as required for indoor unit M-2011

Supply of Split unit with compressor complete with indoor and outdoor units with COPPER COIL, individual controller and with fittings etc.

Split AC with Remote

1.5 TR Split Type AC Unit - 5 Star Rated M-1984

Supply and installation of 5 KVA capacity Automatic VoltageStabilizer with time delay relay M-1989

Supply and laying of 5/8" and 3/8" copper pipe (Extra beyond 3 metres supplied with AC unit)

Supply and laying of communication 1.5 sq.mm. copper flexible cable between indoor and outdoor units. The rate shall be including accessories and necessary fixing arrangement.

Supply and fixing of water drain pipe line (1” PVC Pipe)

Supply and Installation of MS Stand for split units ODU

VENTILATION SYSTEM

Supply, Installation, Testing and Commisioning of Galvanized Sheet Steel Made Jet fans with protection guard with the following specifications 1) 250mm impeller dia jet fans 2) Motor : 0.29 / 1.27 Kw @ 4/2Pole. IP55, Class F insulation 3) Dual speed motor suitable for 300Deg C for 2 hours. 4) 4700 / 9000 CFM. output. 5) Special silencers at the inlet and outlet 6) Mounting brackets for ceiling suspensions 7) Sound level 40/60 dB

Supply, Installation, Testing and Commisioning of Galvanized Sheet Steel Made Fresh Air fans complete with the following specifications. 1) Impeller madeup of die cast alluminium alloy with Hub and blades matching with aerodynamic profile 2) Direction of discharge and rotating position as per requirement 3) Speed: 1550 RPM 4) CFM: 14,000 @ 15mm wg static pressure. 5) KW: 3.7Kw 6) Sound level: 80dB

Supply, Installation, Testing and Commisioning of Galvanized Sheet Steel Made Exhaust fans complete with the following specifications. 1) Impeller madeup of die cast alluminium alloy with Hub and blades matching with aerodynamic profile 2) Direction of discharge and rotating position as per requirement 3) Speed: 1550 RPM 4) CFM: 28,000 @ 30mm wg static pressure. 5) KW: 7.5Kw 6) Sound level: 80dB

Supply, Installation of 20 Gauge GI Duct Sheet of size 600mm x 300mm along with necessary M.S. angle supports, flanges, channels, bolts & nuts etc., complete. The rate is inclusive of transportation charges etc., complete.

Supply and fixing of telephone socket (telephone jack single line RJ 11) on suitable factory made metal box (necessed) with frame and face cover plate etc., complete required with connections

Supply and Clamping of armoured co-axial cable for TV (RG-06) in suitable PVC Pipe 1" thick on wall / ceiling with connected PVC accessories with clamps, saddles etc., complete.

Supply & fixing of TV socket (coaxial jack) on suitable factory made metal box (recessed) with frame and face cover plate etc., complete required with connections

Supply, Installation, Testing and commissioning of 32 channel 8 SATA NVR 3nos with 8TB Hard Disk Drive, New logical and visualized GUI design Dual-OS design to ensure high reliability of system running, ANR technology to enhance the storage reliability when the network is disconnected, Configurable normal or hot spare working mode to constitute an N+1 hot spare system Video Input and Transmission, Connectable to the third-party network cameras Compression and Recording, H.265+ compression effectively reduces the storage space by upto 75%, Full channel recording at up to 12MP resolution HD Video Output  HDMI1 / VGA1 outputs provided  HDMI1 Video output at up to 4K ( 3840 × 2160 ) resolution Storage and Playback, Upto 16 SATA interfaces and 1 eSATA interface for HDD connection, Support upto 10TB capacity for each HDD, Smart search for efficient playback. and smart playback to improve the playback efficiency,Supports VCA search for fire/ship/temperature/temperature difference detection triggered video files, POS information overlay on live view and playback, POS triggered recording and alarm Network & Ethernet Access  Hik-Connect for easy network management, 2 Gigabit Ethernet network interfaces.

Supply of 8MP, Internet Protocol fixed BULLET CAMERA with following specification: ●1/2.5" Progressive Scan CMOS, ● 3840 × 2160 @15 fps,2.8/4 mm fixed lens,01 lux @ (F1.2, AGC ON), 0.028 lux @(F2.0, AGC ON), 0 lux with IR, H.265+, H.265, H.264+, H.264, 2 Behavior analyses ( Line crossing detection, intrusion detection) ● Face Detection ● 120dB WDR, ● BLC/3D DNR/ROI, IP67 complied ●On-board Storage - Built-in micro SD/SDHC/SDXC card slot, up to 128 GB, ● Shutter Speed 1/3 s to 1/100,000 s, ● 3-Axis Adjustment Pan: 0° to 360°, tilt: 0° to 100°, ● rotate: 0° to 360°, 2.8 mm, ● horizontal FOV: 102°, vertical FOV: 53°, diagonal FOV: 124°, ●Lens Mount M12 ● IR Range I5: up to 50 m, ● Image Settings Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser, ● Power Consumption and Current-12 VDC, 0.7 A, max. 7.5W PoE: (802.3af, 36V to 57V), 0.3 A to 0.2 A, max. 9W ● Camera out fitted with metal housing so as to prevent the lens from damages during physical abuse. ● Suitable Stand for Camera Fixing

Supply, Installation, Testing and Commissioning of 55" smart LED TV with following specifications a) Full HD 1920 x1080 (4K monitor) b) IPS pannel c) Slim back light LED module d) 900 PMI e) Triple XD engine f) Dynamic scanning g) ANR h) True colour generator i) 8modes of picture j) picture wizardIII k) Real cinema 24P l) HDMI -3nos m) USB -3nos n) Built in LAN o) Magic remote p) Dimension 1242 x 724 x 55.1min(37).

Supply and fixing of outdoor 4 x 6 PVC box with 102mm x 77mm x 102mm with all fixing accessories.

Supply and Laying of CAT 6 cable in 19mm PVC pipe in Wall or Ceiling Open/Concealed with complete with all necessary accessories etc.

Fixing and Termination of CAT 6 Cable RJ 45Jack Single Point ( Point to Point ) Crimping, Testing and arrangement charges.

Supply and fixing of POE 24 port switch 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line.

Supply, installation, testing and commissioning of Higher end 42U Rack 800mm width, 1000mm depth floor mounted, Front single front & Rear Perforated Door with lock ,LNS unit, Cooling Fan 230V 90 CFM - 4Nos. Shelf 725mm -1No, Modem Tray - 1No, Power Strip 12 x 6/16A Socket & 1.5 meter feed cable and 3 pin plug -1No, 1U - Closed Cable manager 6Nos. with hardware Pocket of Assembled set and all necessary fixing accessories as required.

Supply and Instalatin for 2KVA UPS with Battery, Single Phase UPS (Single Phase In & Single Phase Out) Capacity - System with Battery - 2 Hour

Supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with painting of suitable colour for Camera Pole

PA System

Supply, Installation,Testing & commisioning of 480 watts P.A Mixer Amplifier with the output power of 1350 watts maximum, 500watt rms at 10% Thyristor harmonic distortion(THD), 850watt RMS at 5% THD, 800 watts RMS at 2% THD and the power supply AC voltage ranging from 220-240 volt, 50/60 hertz. with the DC input of 48 volt and 1000watts has tone controls of Bass=+- 10 db at 100 hz weighing 42kg with the speaker output of 2Q,4Q.70volt&100volt has power consumption of 1600VA AC &12A DC and 100db output regulation at 1khz no load to full load ratio. The signal to noise ratio is 60db with the imnput channels of 0.8mv/4.7kq,3*Aux 100mv/50kq.The frequency response of 50-15000hz+-3db.(Make:Ahuja SSA 10000 /Bosch or its equivalent)

Supply, fixing & Testing of 10" gooseneck with suitable base incorporates separate bush switches for momentary and dynamic microphone with 600ohm impedence and has 2.5mv/pa sensitivity and frequency response ranging from 50-15000hz with multi tone chime model.(Make:-ACM66 Ahuja/bosch/its equivalent)

CEIG Liasioning Charges

Sri Balaji Constructions (BID ID -1050875)

S J INFRA (BID ID -1050957)