Supply, installation, testing and commissioning of electro-mechanical equipments at water supply scheme Upgradation Salia.

Amount

WSS Upgradation Salia (Adv. Cost Rs. 45,75,000/-)

Supply, Installation, Testing & Commissioning of Submersible Pumping Unit as per IS 8034 for with following specification are as under : PUMP : Discharge Range = 20000 GPH Head Range= 55-65 mtrs Efficiency = Not less than 50% Speed = 2900 Rpm Type of pump = Submersible Pump Type of fluid to be handled = Clear Water MOTOR:- Motor Rating= 35.00 HP/ As per OEM Method of starting = Star – Delta Speed = 3000 (Sync). Frequency = 50 ± 3 % Hz Working Voltage = 380-415 ± 15% V, 03 phase Efficiency = Not less than 90% Class of insulation = F/Suitable for above parameters Rest of Specification/Details are as per clause 1 of SBD

Fabrication, providing, fitting and lowering of column pipe conforming to IS: 1239 of length 10 Rft into the 200/ 250/300 mm casing dia. production well up to the desired depth ; The job includes Providing and welding of flanges conforming to IS: 6392, Table-17 and PN 16 Size : DN 150 Class: B (Medium) Rest of Specification/Details are as per clause 7 of SBD

Providing/supplying and fitting of G.I flanged Rising Main at site. The Pipe shall be hot dip Galvanized, class-B confirming to IS 1239. The job includes providing and fitting of M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16). Size : DN 150 Class: B (Medium) Rest of Specification as per clause 8 of SBD

Earth work in excavation by manual means in trenches for foundation, drains, pipes, cables (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and reaming of bottom lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed. (All kinds of soil 01 meter from cutting edge)

Filling available excavated earth in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by reaming and watering, lead upto 50 m and lift upto 1.5m.

Providing and laying hand packed stone soling 50 mm nominal size including filling, spreading, dressing, ramming, all leads lifts and all carriages complete.

Centering and shuttering including strutting , propping etc. and removal of form work for Foundation, footings, bases for columns

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering . all work upto plinth level with 1 : 2 : 4 mix (1 cement , 2 coarse sand , 4 graded stone aggregate 20 mm nominal size)

Fabrication, providing and fitting of washout Tee with arm length 1.2 feet each. The Tee shall be fabricated out of G.I pipe with M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) fastened with weld joints on three ends. Size : DN 150 Class: C Rest of Specification/Details are as per clause 09 of SBD

Providing and fitting of, Ductile Iron double flanged, non-rising spindle soft seated glandless gate/ sluice valves as per IS14846 for regulating the water supply outside the pumping units . Size: DN150 PN:1.6/16 Rest of Specification/Details are as per clause 12 of SBD

Providing and fitting of Ductile Iron double flanged, Slanted seat swing check valve( NRV) as per IS 5312. Size: 150 mm PN: 1.6/16 Rest of Specification/Details are as per clause 13 of SBD

Providing, fitting, testing and commissioning of ARV (Air Release valve) as per IS 14845 to be fitted to G.I rising Main. Size: 50mm PN: 1.6/16 Rest of Specification/Details are as per clause 14 of SBD

Fabrication ,Providing and fitting of 90-120 degree bend/elbow to be fabricated out of G.I pipe, 1 m length and flanged on both ends a to make it leak proof. The flanges shall be M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) and welded on both sides. The job includes nuts, bolts, gaskets etc as per site requirement. Size:DN 150 Rest of Specification/Details are as per clause 15 of SBD

Fabrication, providing and fitting of split type MS clamps10 mm thick, 2 ft long and 3 inch wide for lowering and holding of pumping unit fitted. The job includes the cost of required size of nuts and bolts. Size: 150 mm Rest of Specification/Details are as per clause 16 of SBD

Fabrication of gantry mechanism/CGI Shed by way of providing Structural steel in built up sections , trusses and framed work, including cutting , hoisting , fixing in position and applying a priming coat of steel primer and 02 coats of paint of approved shade all complete welded. The drawings and Dimensions for Gantry/CGI Shed will be provided by Site In Charge at the time of execution of job Rest of Specification/Details are as per clause 21 of SBD

Fabrication of gravel Hooper for proper feeding of gravels to the borewell and platform to bear the load of pumping unit, column pipes etc Rest of Specification/Details are as per clause 22 of SBD i. In stringers , treads , landings etc of stair cases including use of chequered plate wherever required , all complete

Providing and fitting of M.S 4 inch hinges -6 no and M.S handle heavy -2no., Anchor bolts with nuts (M16) of 0.3 m long = 04 No. Metallic strip (350mm×50mm×3mm) = 02 No. Rest of Specification/Details are as per clause 23 of SBD

Supply, Installation and testing of manual type triple gear chain pulley block along with mnrail geared travelling trolley y of proper specifications Capacity = 3 ton Rest of specification as per cluase 24 of SBD

Creation of pole mounted , outdoor type Electric Sub Station by way of S/I/T/C of 11/0.433 KVA , 3 Phase Distribution Transformer with Bimetallic Terminal connectors Energy level -2 Aluminum wound Specifications conforming to IS : 1180 (Part 1) 2014 with latest amendments Type of cooling: ONAN. Rating: 100 KVA HT Transformer, 3 phase (Level 2). Manufacturers certificate be apended and rest of specification as per cluase 26 of SBD

Providing and fitting G.I Channel /Angle/ Flat of sizes including clamps as per details in Clause 27 of SBD

Supply, Installation, Testing and commissioning of Polymeric Gang operated Air break switch, outdoor type, triple pole, suitable for vertical installation, complete as per IS specs Rest of Specification/Details are as per clause 28 of SBD

Supply, Installation, Testing and commissioning of 11KV polymer fuses Set Horn Gap as per details in Clause 29 of SBD

Supply, Installation, Testing and commissioning of Gapless Surge arrestor station class as per details in Clause 30 of SBD

Supply and fitting of 11 KV polymeric composite pin insulator as per details in Clause 31 of SBD

Supply, installation, errection of 9 mtrs long H.T pole of specifications ST- 410 (sp-33) as per details in Clause 32 of SBD

P/F of Galvanized nuts, bolts of various sizes as per site requirement.as per details in Clause 33 of SBD

P/F Danger Plate with clamps as per details in Clause 34 of SBD

Providing and fixing G.I Barbed wire for anti climbing/ anti climbing devices with clamps as per details in Clause 35 of SBD

Providing and Fitting of PG clamps

Providing and fitting of Galvanized stay set complete as per details in Clause 36 of SBD

Painting of poles Red oxide

Painting of poles Aluminum paint

Providing and fitting of ACSR as per details in Clause 39 of SBD

Supply, Installation and Testing of 50 Sq mm XLPE Aluminum H.T cable (ABC type ) of 11 KV grade with following specs. Size (cross sectional area in sq mm) = 3×50 with reinforced wire Phases: Red, Yellow, Blue

Providing and fitting of Anchoring clamps required for holding of 3 – Core , 35 Sq. mm H.T AB Cable as per details in Clause 40 of SBD

P/F of 11 KV cable termination kit as per details in Clause 41 of SBD

Providing and fitting of LT Distribution box for HT transformer Capacity of transformer: 100 KVA Rest of Details/Technical specification are as per clause 42 of SBD

Providing and fitting of PRODIGY LT Metre of following specification complete with all fixtures required for fitment at site Type: E3L100, 3 Phase, 4 wire Measurements offered: KWh,KVARh,KVAh,KVA Voltage : 3x240V(415v),50HZ Ib : 40A Imax: 200A Battery: Lithium

Fabrication Providing and fitting of modular control panel of appropriate size fabricated out of 14SWG sheet having required openings/vents and protection class: IP-55 and fitted with accessories MU-G50 and Rest of Details/Technical specification are as per clause 43(h) of SBD

Providing, fitting, testing and commissioning of Manually operated copper wound, 3-phase, AC power supply multi step voltage stabilizer. Rating::75 KVA Manufacturers test certificate to be apended and rest of specification as per clause 44 of SBD.

Providing and Fitting of 3 /3.5/2-Core, XLPE Armoured Aluminium Cable conforming to IS: 7089 part 1st as service line from the HT transformer to control as per clause 46 of SBD. i) 95 sqmm, 3.5core, LT cable

ii) 10 sqmm, 2 core, LT cable

Providing and fitting of 3-Core flat submersible copper cable conforming to IS: 694 (Part 1st) – 1964 & IS: 694 (Part 2nd) - 1964 as per details in Clause 47 of SBD Size: 25 sq.mm

Providing and fitting of 50 mm square single core copper cable for interconnecting various electrical gadets as per IS 694: 2010 along with thimbling as per requirement.

Providing and Fitting of cable tray of suitable size for carrying the cable inside the machinery room.

P/I of earthing station for substation, LT panel, DG set and stabilizer comprising of company fabricated earthing electrode as per IS: 3043. Rest of Specifications/details are as per specification in clause 48 of SBD

Illumination of Premises: Providing and erection of 9 Mtr long Hot Dip Galvanized octagonal pole (single Section) with bottom 150mm, top 75mm wide, thickness 3mm with 70 Microns Zinc coating having inside arrangement for providing of power connection along with following items. 1) 3 Way Terminal Connector 20 Amp. 2) 3 No MCB 8 Amp. Rest of Details/Technical specification are as per clause 50 of SBD

Providing, installation, testing and commissioning of area lighting 120 Watt LED (Street Light Type) on top of octagonal pole Having following specs: Input: 90-240 V 50 Hz Power Factor: >0.9 Rest of Details/Technical specification are as per clause 51 of SBD

Providing and installation of Junction Box with DP 32Amp MCB to serve as amin switch for LED lighting. Rest of Details/Technical specification are as per clause 52 of SBD

Providing, Installation and testing of 2KVA fully automatic voltage stabilizer Rest of Details/Technical specification are as per clause 53 of SBD

Supply, installation, Testing & commissioning of 1000VA Full Sine wave power inverter with 12V, 180AH Tubular inverter Battery Rest of Details/Technical specification are as per clause 54 of SBD

Providing, laying & fixing with adhesive/bonding material of insulation rubber mats on the floor of the pump house, covering area around electro-mechanical machinery for safeguarding the life & limb of the workmen Rest of Details/Technical specification are as per clause 55 of SBD

TOOL KIT Maintenance The tool kit for maintenance as per details in Caluse 56 of SBD

Providing of good quality conveinence and utility items as per details in Caluse 57 of SBD

Fabrication of 7’ (L) x 6’(B) x 1.5' (H) angle iron bed for operators with back-height of 2 feet. The detailed drawing will be provided by site incharge. Rest of Details/Technical specification are as per clause 58 of SBD

Providing and fitting of 19 mm thick multilayered ply sheet of size 6 x 3 feet, 3 nos. Rest of Details/Technical specification are as per clause 59 of SBD

Providing of solar/ electrical lantern chargeable on both solar & electrical 220v supply.

Providing of 1 KW heat convector for operators for winter season.