Construction of Health Sub Centre Building at Sarjamda of Jugsalai-cum-Golmuri Block

Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item-A)and disposal of excavated earth as obtained to a distance up to 50mts. Including all lift,levelling,ramming the foundation trenches, removing root of treese, shrubs all complete as per approved design, building specification and direction of E/I.

Extra for earth work in hard soil as per specification and direction of E/I. ( Videclassification of soil item B )

Providing coarse cleanSand filling in foundation trenches or in plinth including ramming and waterind in layers not exceeding 150mm. Thick with all leads including cost of materials, labour, royalty and taxes all complete as per building specification and direction of E/I

Providing designation 75 B Brick flat soling joints with local sand including cost of watering taxes and royalty all complete as per building specification and direection of E/I

Providing and laying in position cement concrete of specified grade excluding Centering, shuttering All work up to plinth level as per building specification and direction of E/I. for P.C.C M-150 in (1:2:4) up to Plinth level

Providing and laying in position specified grade of reinforced cement concrete all work up to plinth level but excluding cost of reinforcement, Centering, shuttering and finishing as per building specification and direction of E/I. for R.C.C M-200 in (1: 1.5: 3) Up to Plinth

Providing designation 75 B Brick work in C.M.(1:6) in Foundation with approved quality of clean coarse sand of F.M.2.00 to 2.5 including 10 mm thick mortar joints,cost of screening, scaffplding, raking out joints to 15mm. depth, curing, taxes and royalty all complete as per building specification and direection of E/I

Earth filling in foundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)

Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) inin superstrure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 112mm thick reinforcement designtion 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:4) in supertructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including cost of screening materials scaffoliding raking out joints to 15mm depth curing taxesand royalty ( but excluding theb cost of reinforcement) all complete as per building specification and direction of E/I.

Reinforced cement concrete work in wall (any thickness) including attached pilaster, buttresses, plinth and string courses, fillerts, columns, pillars, piers, abutments, posts and struts etc, above plinth level up to floor five level, but excluding cost of reinforcement, Centering, shuttering and finishing as per building specification and direction of E/I. for R.C.C M-200 in (1: 1.5: 3) Above Plinth to 5 Level

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, stair cases and spiral stair cases above plinth level up to floor five level but excluding cost of reinforcement, Centering, shuttering and finishing as per building specification and direction of E/I. for R.C.C (1: 1.5: 3) Above P.L to 5 Level

Providing M.S.Steel reinforcement 8 mm dia rods as per approved deige and drawing including carriage of M.S.bars to work site cutting,bending and binding with annealed wire cost of wire,removal of rust, placing the rods in position all complete as per building specification and direction of E/I (@15% of total Reinforcement)

Providing M.S.Steel reinforcement 10 mm dia rods as per approved deige and drawing including carriage of M.S.bars to work site cutting,bending and binding with annealed wire cost of wire,removal of rust, placing the rods in position all complete as per building specification and direction of E/I (@20% of total Reinforcement)

Providing M.S.Steel reinforcement 12 mm to 20 mm dia rods as per approved deige and drawing including carriage of M.S.bars to work site cutting,bending and binding with annealed wire cost of wire,removal of rust, placing the rods in position all complete as per building specification and direction of E/I (@65% of total Reinforcement)

Providing Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Providing Centering and shuttering including strutting, propping etc. and removal of form forColumns, Pillars, Piers, Abutments, Posts and Struts

Providing Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Providing Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Providing Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Providing 12mm water proof cement Plaster in cm (1:3) in top of roof with clean coarse sand of F.M.1.5 with 5% cico or any other approved water proofing compound including cost of screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I

Providing 6mm cement Plaster in cm (1:4) in Ceiling with clean coarse sand of F.M. 1.5 including cost of screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I

Providing 12mm cement plaster in cm (1:6) in both side wall with clean coarse sand of F.M.1.5 including cost of screening, curing with all leads and lifts of water, scaffolding, taxes and royal ty all complete as per building specification and direction of E/I

Supplying, fitting and fixing 35 mm thick solid core type non- decorative single leaf flush shutters in doors and windows with black board core blended with high quality phenol formal dehyde synthetic resin both side commercial veneered of standard make with oxidised iron fittings as per approved design all complete as per building specification and direction of E/I.

Provinding and fixing wooden moulded beading to door and window frames with iron screws, pluge and priming coat on unexposed surface etc. Complete. (50x20 mm)

Providing and fixing bright finished brass 100 mm mortice latch and lock ISI marked with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS: 1868) aluminium level handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868 transparent or dyed to required colour and shade, with necessary screws etc. Complete.

Providing and fixing aluminium extruded section body tubular type universal hydrauilic door closer (having brand logo with ISI, IS: 3564 embossed on the body door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm) with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing pressed steel door frames confirming to IS : 4351 manufactured from commercial mild steel sheet of 1.60mm thickness including hinges jamb, lock jamb bead and if required angle threshold of mild steel angle of section 50 X 25mm, or base ties of 1.60 mm pressed mild steel welded or rigidly fixed together by mechanical means including M.S pressed bult hinges 2.5mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pretreatment of the surface as directed direction of E/I. 1.2 Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately)

Supplying fitting and fixing M.S. Grill made of 20x6 mm M.S. flats as per approved deesign and drowing ,properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I.

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Suppliying, fitting and fixing callapsible gate of approved size and make rpopoerly fabricated with vertical double channe3ls 20x10x2mm at 100mm centres and braced with M.S flat diagonals 20x3mm with top and bottom rails of T iron 40x40x6mm with 30mm dia, steel pulleys complete with bolts, nuts locking arrrangements, stoppers, handls, including applying a priming coat or red lead paints, car riage, hoisting and taxes all complete as per building specification and direction of E/I.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z section and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size including necessary filling up the gaps at junctions, i.e at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling C.P brass/ stainless steel screws all completed as per specification and direction of E/I (Powder coated aluminium mimimun thickness of powder coating 50 micron)

Providing and fixing aluminium shutter of doors, windows, ventilators including hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required. (Fitting shall be paid for separately) (Powder coated aluminium mimimun thickness of powder coating 50 micron)

Supplying fitting and fixing glass panes including supplying putty. Beads and nails after taking out old and broken glass panes and disposal of debris all complete as per building specification and direction of E/I. (5.5 mm plain)

Providing single layer Naria- tiles in roof including cost of all labour and materials, taxes, all coplete as per building specification and direction of E/I.

Providing and laying 25mm thick kotah stone slab flooring of approved size texure and colour over 19mm thick base of lime mortar (1:1:1) (limeputty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. (iv) 600X600 mm size

Providing and laying 25mm thick kotah stone tiles in risers of steps skirting and pillars of approved size texure and colour laid over 12mm thick cement mortar (1;30 and joined with grey cement slurry mixed with pigment to match the shade of the slab including rub bing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm .

Providing and laying Ceramic glazed floor tiles of size 300x300 mm thickness to be specified by the manufacturer of 1st quality conforming to IS: 15622 of approved make in colours such as white lvory Grey Fume Red Brown laid on 20 mm thick cement mortar (1:4) jointing with grey cement slurry @ 3.3 kg/sqm including pointed the joint with white cement and matching pigment etc. complete including cost of curing, taxes and royalty as per building specification Engineer in charge.

Providing and laying 1st quality Ceramic glazed wall tiles thickness to be specified by the manufacturer in wall over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointed with white cement including rubbing polishing and cost of curing, taxes and royalty all complete as per building specification Engineer in charge.

Providing and fixing Granite 18mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for flooring. Kitchen platforms, vanity counters, window sillls, facias and similar locations of required size, approved shade, colour and taxture laid over 20 mm thick base cement mortar (1:4) joints treated with white cement, mixed with matching plgment, epoxy touch ups, including rubbing, curing moulding and polishing to edges to give high gloss finish etc. complete at all level. (Granite of any colour and shade Area of slab over 0.50 Sq.M)

Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by the rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I.

Finishing walls with Acrylic Smooth exterior paint of requied shade, New work ( Two or more coat applied @ 1.67 ltr./10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Finishing walls with Acrylic Smooth exterior Local Art paint of requied shade, New work ( Two or more coat applied over and including priming coat of exterior primer applied as per E/I)

Provding two coats of Synthetic Enamel paint of approved shade and make ove steel surface including cleaning the surface thoroughly cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Provding two coats of Synthetic Enamel paint of approved shade and make over new wooden surface including cleaning,removing dircet scales,smokes, grese and cleaning the surface taxes and royalty all complete as per building specification and direction of E/I (Mode of mea surement-Area shall be multiplied by the co-efficient as indicated in building specifications)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and fixing circular/ Hexagonal cast iron or M.S sheet box for ceiling fan clamp of internal dia. 140 mm, 73 mm height, top lid of 1.5 mm thick M.S sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S sheet box by means of 3.3 mm dia round headed screws, one lock at the corners, clamp shall be made of 12 mm dia M.S bar bent to shape as per standard drawing.

Providing 12mm thick cement paster in cm (1:3) with 1.5mm cement punning including curing, carriage of waterwith all leads and lifts as per building specification and direction of E/I

ADD CARRIAGE COST (Diff.Carriage Cost as per Km)

(a) Cement & Steel from Lead Upto 15 Km

(b) Sand from (3K+27P) = 30 Km

(c) Stone Chips from (1K+29P) = 30 Km

(d) Brick from (2K+8P) = 10 Km

200/150 mm dia Deep borewell : Supplying all materials, labours, tools & equipments for drilling 200/150 dia Borewell in any kind of soil/rock by using DTH supper Rig Machine and bell hammer technology inclusive of molillisation demolillsation of rig air compressor all accessories tools and plants labour etc. including of transportation charges up to the site & all complete job as per direction of E/I.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 50.00 M to 125.00 M

Supplying assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well casing pipe of required dia. conforming to IS: 12818 including required hire labour charges fitting & accessories etc. all complete for all depths as per direction of E/I. (200 mm nominal size dia)

Development of tube well in accordance with IS: 2800 (part-I) and IS: 11189 to establish maximum rate of usable water yield withoutsand content (beyond permissible limit) withrequired capacity aircompressor, running the compressor for required time till well isfully developed measuring yield of well by "V" notch method or anyother approved method measuring static level & draw down etc. bystep draw down method collecting water samples & getting testedin approved laboratory i/c disinfection of tubewell all complete including hire & labour charge of air compressor tools & accessoriesetc all as per requirement and direction of E/I.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe removable as per requirement all complete for borewell of 200 mm dia.

Providing and fixing M.S clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part-I) including necessary bolts & nuts of required size complete 200 mm dia.

Supplying 100 mm dia Submersible pump sets confirming to 8034 and motor confirming to IS: 9283 pump shell be suitable for various delivery head and discharge with stainless steel pump sheft and polypropylene/ noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/ fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/ double run shell be provided with each pump. Submersible pump set 100 mm dia (with polypropylene/ noryl impeller) up to 20 stages 2HP S.Pump

Supply fitting and fitting of standared make 2.00 HP submersible pump starter Pannel Board with arrangement of all necessary protection, including all taxes, all complete job as per direction of E/I.

Supplying fitting and fixing 3 crore 4 sq.mm flat copper submersible cable of Finolex/Hevels make including all taxes etc. all complete job as per direction of E/I.

Supply fitting and fixing lowering 40 mm dia G.I collumn pipe including of required fittings, solvent etc completed as per direction of E/I. (M-930K(v) Rs.300.00/met. +M-1051,Rs.5.58/met.)

Supplying,fitting & fixing vitrcous white glazed earthen ware I.W.C. of parry Hindustan or any other I.S.S. approved make with 100mm. H.C.I."P" trap 15 litres C.I. Pull and let go flushing cistern of names or other I.S.S Equipment make complete with all fittings C.I or C.C brackets 32mm alkathene/PVC. telescopic flush,pipe about 2M long with one brass coupling & clamps G.I.Chain & pull including supplying & fixing a pair of vitreous white glazed earthen ware footrest to be fixed in floor 15mm C.I.body brass spindle stopper cock of weight not less than 50 gms 15mm PVC Connection pipe 450mm long and the exposed pipe & cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification & direction of E/I (White Vitreous China Orissa pattern W C pan of size 580 X 440 mm with integral type foot rest.)

Supplying, fitting & fixing 40 mm high vitrcous white glazed earthen E.W.C. with 'P' trap of parry Hindustan or any other I.S.S. approved make including supplying & fixing 15 litres C.I Mosquito proof low down flushing cistern of approved make with complete fitting with C.I. handle and R.S or brackets with telescopic flush,pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grams 15 mm P.V.C alkathene pipe 45cm long with brass coupling at both ends and white/ black plastic soid state seal and lead of commander/ cuckoo or other I.S.S make withhinges or screws etc. painting pipe and cistern etc. with 2 coats of approved pain over a coat of red oxide priming all complete as per specification & direction of E/I (White Vitreous China Orissa pattern E.W.C Pan of approved size)

Providing and fixing Wash basin with C.I/M.S brackets, 15mm C.P. Brass pillar taps 32mm C.P brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wtherever require. (3) white vitreous china wash basin size 550x400 mm with a pair of 15mm C.P brass pillar taps.

Supplying, fitting and fixing the following item complete with all materials as per specification and direction of E/I (a) Glass shelf with C.P brass rail (i) 600 x 125 mm glass shelf complete.

Providing and fixing PTMT Bottle Trap for Wash Basin and sink bottle trap 31 mm single piece moulded with height of 270 mm effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms.

Providing and fixing PTMT Liquid Soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fitting of approved quality and colour weighting not less than 105 gms.

Providing and fixing PTMT Towel Ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealed fittings arrangement of approved quality and colour weighting not less than 88 gms.

Providing and fixing C.P. Brass bib cock of approved quality conforming to IS: 8931

Providing and fixing C.P. Brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931 (a) 15 mm nominal bore

Providing and fixing Toilet Paper Holder of C.P. Brass

Providing and fixing on wall face unplasticised Rigid PVC rain water pipe conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10 mm gap for thermal expansion. (i) Single socketed pipes. (1) 75 mm diameter

110 mm diameter

Providing and fixing on wall face unplasticised PVC mouided fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10 mm gap for thermal expansion. (1) 110 mm diameter

Single tee with door 110x110x110 mm

Bend 87.5 dgree

Shoe Plain

Providing and fixing unplasticised PVC pipes clips of approved design to unplasticised PVC rain water pipe by means of 50x50x50 mm hard wood plugs, screwed with M.S screws of required length, including cutting brick work and fixing in cement mortar (1:4) and making good the wall etc. complete. (1)75mm dia.

110 mm diameter

Providing and fixing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing this including jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per the direection of engineer incharge. Internal work- Exposed on wall. (2) 20mm nominal outer dia pipes

25mm nominal outer dia pipes

32mm nominal outer dia pipes

40mm nominal outer dia pipes

50mm nominal outer dia pipes

Providing and fixing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing this including jionting of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the wall same including testing of joints complete as per the direection of engineer incharge. Conceealed work including cutting chase and making good the wall etc. (1)15mm nominal outer dia pipes

20mm nominal outer dia pipes

25mm nominal outer dia pipes

32mm nominal outer dia pipes

Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design.

Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank ISI: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflowpipes but without fitting and the base support for tank.

Wiring for light point/ fan point/exhaust fan point / call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular switch ,modular plate, suitable GI box and earthing the point with 1.5sq mm FR PVC insulated copper conductor single core cable etc as required. (Group C)

Wiring for light/power plug with 2 x 4 sq.mm FR PVC insulated, copper conductor ,single core cable in surface /recessed PVC conduitalong along with 1 No. 4 sq mm FR PVC insulated copper conductor single core cable for loop earthing as requried .

Wiring for light/power plug with 4 x 4 sq.mm FR PVC insulated, copper conductor ,single core cable in surface /recessed PVC conduitalong along with 2 No. 4 sq mm FR PVC insulated copper conductor single core cable for loop earthing as requried .

Wiring for circuit / sub main wiring alongwith earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/ recessed PVC coduit as required.

2X1.5 sq mm +1 x 1.5sq mm earth wire.

2X2.5 sq mm +1 x 2.5sq mm earth wire.

4 X 2.5 sq mm +2 x 2.5 sq mm earth wire.

4 X 10 sq mm +2 x 6 sq mm earth wire.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with final tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

S/F of following sizes of PVC conduit alongwith the accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

20 mm PVC coduit

25 mm PVC coduit

Suppling and fixing following moduler type switch /socket on the existing modular plate & switch box including connection but excluding modular plate etc. as required.

5/6 amps one way switch

15/16 amps one way switch

5/6 amps 3 pin socket outlet

15/16 amps 6 pin socket outlet

TV anteena Socket outlet

S/F stepped tube electronic fan regular on the existing plate switch box including connection but excluding modular plate etc. as required.

S/F modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box along with moduler base & cover plate for modular switches in recess etc. as required.

1 or 2 module (78x78x45 mm) for Telephone & TV outlet.

4/5 module (78x140x50 mm)

6 module (78x205x50 mm)

S/F 2 pin 5 amp Ceiling rose on the existing junction Box/ wooden block including connection etc. as required.

S/F Brass batto/Angle Holder including connection etc. as required.

S/F Ding dong sound call bell single phase 230 volts complete as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. Mm FR PVC insulated, copper conductor, single core cable etc. As required.

Installation of exhaust fan up 450 mm sweep in the existing opening including making the hole to suit the size of above the fan, making good the damage, connection, testing, commissioning etc. As required.

Providing and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Providing and fixing of following ways, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But with out MCB/RCCB/Isolator) (6) 8 way (4+24),Double Door Horizontal Type

Providing and fixing 6 Amp to 32 Amp rating 240 volts, 10 KV "C" Curve Miniature Circuit Breaker suitable for inductive loads of following poles in th existing MCB DB complete with connections, testing and commissioning etc. As required. (1) 6 / 32 Amp Single Pole

40 Amp TPN

Providing and fixing of following rating double pole (Single pole & neutral), 240 volts, resudual current circuit breaker (RCCB), having a sensivity current 30 miliampere in the existing MCB DB complete with connection, testing & commissioning etc. As required. (2) 40 Amps

Earthing with G.I earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) as required

Providing and fixing 25 mm x 5 mm G.I strip on surface or in recess for connections etc. As required.

Providing and fixing 6 SWG dia. G.I wire on surface or in recess for loop earthing along with existing sufface/ recessed conduit/ submain wiring/ cable as required.

Supply of XLPE insulated PVC sheathed heavy duty, armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts. (conforming to IS- 7098. Part-1) 4 core, 16 sq,mm

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. (1) run of cable

Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Upto 35 sq. Mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/ XLPE aluminium conductor cable of 1.1 KV grade as required. (33) 4 x 16 sq. Mm (28mm)

SITC of following rating recess / surface mounted LED round /square shape down light luminarie with pressure die cast housing for single phase supply voltage Luminarie shall be confirm to IS: 10322 part - 5/ section - 2 or IEC: 62722 with all neccessary accessories as required. Make:- Havells/ Philips/ Crompton/ Wipro. (4) 18/20 W LED Round Down Light (Surface)

Bulk Head fitting with 9/10 Watt LED

S.I.T.C of following rating surface mounted LED Tube Lighting Fitting Suitable for 230V, 50 Hz, Single Phase Supply etc. Complete as required.

10/12 W LED Tube Light

20/22 W LED Tube Light

SITE of 300 mm (12") Exhaust fan (Metal body) suitable for single phase 230 volts, 50 Hz, AC supply complete with motor, louvers/shutters etc. Complete as required. Make :- Usha/Crompton/Havells.

Supply, Installation, Testing and Commissioning of following size fan 3 Blades confirming to IS:374:2019 including wiring the down rods of stranded for 230 V 50 Hz, single phase supply etc. complete as required. (3)1200mm (48") BLDC 5 Star rating 32W Ceiling Fan of approved make etc. without regulator

Add : 18% G.S.T.

Add : 1% Labour Cess

Please Enable Macros to View BoQ information