PROVN OF SEPTIC TANK AND SOAKAGE PITS FOR CANDIDATE LINES AT SCN AND OTHER SANCTIONED WORKS UNDER GE (WEST) JRC

Amount

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m depth for foundation etc or for shafts wells cespits, manholes, pier holes,laying of UG cables and getting out etc n.exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil.

Returning filling in layers including leveling watering and well ramming in layers n.exc 25 cm thick compelte all as specified.

Removing surplus spoil to a distance not exceeding 50 m and depositing where directed at a level not exc 1.5 m above the starting point.

M & L river sand in trenches as cable cushioning 8 cm below the cables and 15cm above the cable which is to be punned down to 10m all as specified and directed.only punned thickness will be measured.

M&L for salt glazed stonewere drain pipe laid in trenches and joints as specified bore of pipe 150mm.

M&L cement concrete type D2 1:4:8 (40 mm grade aggregate)as in concrete bed to drain pipes 150mm internal dia incl paking under and haunching against the pipe sides of pipe after they are and tested all as specified.

M&L PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate ) as in foundation filling, mass concrete etc complete all as specified.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6 M mean radius built in CM 1:4 including in circular well steining (any radius constructed from the base of curb) all as specified and directed by Engr-in-charge.

M&L for 15 mm thick cement plaster in cement mortar 1:4 with water proofing compound as per manufacturer's instructions to brick or concrete surface finished even and smooth without using extra cement and using waterproofing compound all as specified (WPC shall be measured and paid separately)

Supply only integral water proofing compound

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc

M&L for PCC (1:2:4) type B-1(using 20 mm graded stone aggregate) as in cills, PCC blocks, coping, benching, water troughs, seismic and other similar bands, plinth bend, etc including weathering slightly rounded or chamfered angles and throuting , including necessary form work etc all as specified.

M&L for precast cement concrete type B-1 1:2:4 (20mm graded aggregate) and set in Cement Mortar (1:4) as in landings, manholes cover slabs, chajjas, shelves and similar articles including necessary form work all as specified and directed.

M&L for MS TMT bars 10 mm and over dia and cut to lenth, bent to shape required incl cranking bending spirally for hooping for clos hooking ends and binding with and incl MS wire (annealed) not less than 0.9 mm dia.

Cleaning and cutting into existing Manholes for connecting new drains/pipes up to 225 mm bore, making good to pipes and rendering , cutting out existing benching for and forming branch channel ( 1/2 round or 3/4 section ) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required complete all as specified and as directed by Engr-in-Charge

Taking out liquid/solid content from manholes, sump, septic tank either maually or by pumping, cleaning thoroughly including disposal of liquid/solid content out side Army area complete all as specified.

M & L for provn of septic tank including excavation,PCC in fdn,Brick work in CM (1:4),RCC slab including precast RCC cover slabs,rendering in CM(1:4), vent shaft & sludge chamber for 60 users complete all as specified and directed. Drg No, CEJZ/STD-247/07 sheet No 1 to 24

Material and labour for 3.00 metre dia and 7.50 metre effective depth soakage well, including necessary excavation in any type of soil, plain cement concrete 1:3:6 in foundation, honey combing masonry wall, with top ring of M-25 concrete, intercepting chamber and screen chamber made of brick masonry in cement mortar 1:6, RCC precast cover slab in HD-20SFRC cover, interconnecting pipes of RCC/DWC, filled with brick bats etc complete all as specified and as directed. Drg No, CEJZ/STD-247/07 sheet No 1 to 24

Taking down cement plaster including raking out joints, hacking for key,scrubbing down with water built in cement mortar all as specified and as directed.

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement

M & L for preparation of newly plastered surface of walls and applying two coats of cement base paint over a coat of chalk whiting primer complete all as specified and as directed by Engr-in-Charge.

M&L preparation of old decorated surface of wall and applying one coat of cement base paint complete all as specified and as directed by Engineer-in-Charge.

M & L for preparation of newly plastered surfaces of walls and apply three coat of white wash complete all as specified and directed.

M & L for preparation of old decorated plastered or unplastered surfaces and apply one coat of white wash on walls including cornices etc all as specified and directed

M & L for applying one coat of synthetic enamelled paint including preparation of old decorated steel surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge

Demolition of cement concrete in ground floor and paving not exc 15 cm thickness (below or above ground level), complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 Type C-1 using 40mm graded aggregate as in plinth protection/path complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing and removing serviceable tiles to store.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square or rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match including 15mm thick screed bed in cm 1:6.

M&L for ceramic coloured tiles of size 300x200mmx7mm thick, on verticals surfaces, set and jointed inneat cement slurry and pointed in coloured cement to match including 10mm thick backing coat plaster in CM 1:4

Taking down Chowkhat or frames not exceeding 1.5 Sqm each with shutters(Without taking off shutters from the frames.

S&F aluminum frame powder coated for doors, windows, ventilators with one or more rebates including jointing cleat for fixing etc. complete all as specified and directed.

S&F anodised aluminium window (Sliding or side hung shutter) and ventilator shutters, with powder coating (minimum thickness of powder coating 50 micron) side hung/ sliding type without sash bars, aluminium sections weighing not less than 1.0 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21,100mm long (2 no.) suitable handle (1 no.) for each shutter complete all as specified.

S&F Prelaminated PVC solid door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinfoced with MS square tube, suppling and fixing in opening as per specification and drawing.

S&F Factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and as directed

Material and labour for 5.5mm thick sheet glass ordinary quality including solar control film 25 micron reflective type sticked on glass pane as per instructions of manufacturer and glazing fixed with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

Dismantling of water tanks (PVC/RCC of any description) exc 500 ltr and n.exc 1000 ltr capacity and removing from site complete all as specified and as directed

S&F 1000 ltr capacity rotational moulded polythene tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and as directed

S&F 20mm Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair

S&F ball float valve PTMT with epoxy coated aluminimum rod for 20 mm bore pipe high pressure with polythelene high density float and complete screwed for iron pipe.

Taking up or down steel tubing 15mm bore and connection including cleaning for refixing or removal to store.

All as per item No 42 here-in-before but 20mm dia .

S&F steel tubes medium grade galvanisedwith all fittings and fixed complete to wallsand ceiling or laid in floor bore of pipe 15mm dia.including making hole in RCC slabs for vertical pipes & making good the same with Cement Concrete 1:2:4.

All as per item No 44 here-in-before but 20mm dia.

S&F PVC valveless syphonic action type flushing cistern, low level white with inlet ball valve flaot and handle including brackets. 10 ltr capacity in repair.

S&F Plastic water closed seat white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium plated or aliminished hinging device fixed in repair.

S&F in repair vitreous china wash hand basin (pedastal pattern) white flat back, size 550mmx400mm fixed on and including cast iron cantilever brackets 32mm dia brass waste coupling and including fixing of tap waste fitting and waste pipe and union complete all as specified and as directed . Note: pillar tap shall be measured as supply only under respective items

S&F in repair Orrisa pattern WC in ground or first floor vitreous china white of size 580mmx440mm fixed in repair incl provision of lime concrete bedding and P trap and breaking up of existing damaged WC seat and connecting flush pipe etc complete all as spd. and directed by E-in-C

S&F Vitreous China wash down Water closet pan (pedestal pattern) "with plastic water closet seat cover closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging divice (excluding flusing cistern and flush pipe) in repairs complete

S & F in repairs brass chromium plated jet/health faucet for pedestal pattern water closet including PVC flexible pipe alongwith complete necessary fittings all as specified and directed by the Engr- in- Charge.

S&F in repairs vitreous china urinal half stall type, white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with including 60mm brass screws, pointing around urinal back in cement complete all as specified and as directed by Engr-in-Charge.

S&F in repair PVC connection 15mm dia and 450mm long with both ends brass fly nut complete all as specified and as directed.

S&F in repairs stainless steel toilet paper holder with gutties and steel screws on walls as directed and approved complete all as specfied

S&F in replacement 32mm dia PVC waste pipe for WHB/urinal complete all as specified and as directed.

S&F in repairs for 15mm dia of pipe bib taps, cast copper alloy fancy type and chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed.

S&F in repairs for 15mm dia of pipe angle valves, fancy type and chromium plated screwed down high pressure with crutch or butterfly handle screwed bothends for iron pipes or for unions and fixed.

S&F in repair 15mm dia fancy type pillar taps cast copper alloy with capstan heads chromium plated scewed down high pressure with long scrwed shanks and fly nuts screwed for iron pipes

Supply only 32mm dia waste fitting brass chromium plated for basin with long screwd shanks and fly nuts flange end bedded in red lead cement and other end fixed

Taking down eaves gutters and rainwater pipes/sewage pipe (any size or pattern), including all fittings,heads,shoes,bends,swan necks etc complete.

S&F 110 mm bore PVC pipes single socketed in any length with rubber ring joints fixed to walls or laid in floor, complete all as specified and directed.

S&F 75 mm bore PVC pipes single socketed in any length with rubber ring joints ixed to walls or laid in floor, complete all as specified and directed.

S&F 110 mm dia PVC (SWR ) bends any radius complete all as specified and as directed.

S&F 75 mm dia PVC (SWR ) bends any radius complete all as specified and as directed.

S&F 110 mm dia PVC (SWR ) junction single, (Single T) equal or unequal with rubber rings ljoits fixed to walls complete all as specified and as directed.

S&F 75mm dia PVC (SWR ) junction single, (Single T) equal or unequal with rubber rings ljoits fixed to walls complete all as specified and as directed.

S&F PVC(SWR) floor trap plain with grating including jointing with solvent cement to waste pipe diameter of outlet 75mm, complete all as specified and directed.

S&F in repairs Chromium plated grating 125mm dia circular of approved make and fixing with cement mortor 1:3 on Nahani trap or floor trap.

S&F Urinal spreader of CP for fixing 15 mm dia pipe all as specified.

M&L Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc, and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

S&F 4mm thick superior quality shelves (corner), made of transparent acrylic sheet, set of three, size 30x30cm, 25x25cm, 20x20cm complete all as specified and as directed.

S&F soap dispenser complete all as specified.

Supply & Fixing 100mm size butt hinges extruded aluminum alloy with galvanised mild steel hinge plate

S&F Aluminum anodized barrel tower bolt of extruded section of size 150mm

S&F extruded Aluminum alloy handle fabricated of size 150mm

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even smooth without using extra cement complete all as specified and as directed.

M&L plastering 5 MM thick in cement mortar (1:3)with 0.71mm dia and 25mm chiken wire mesh as specified furnished even & smooth without using extra cement as on ceiling, complete all as specified and directed.

M&L for preparing new plastered surfaces of ceilling and applying three coats of white wash.

M&L for preparation of old surfaces of ceiling including complete removal scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc including cornices, pilasters etc (plastered or unplastered surfaces) and applying three coat of white (lime) wash complete all as specified and as directed by Engineer-in-Charge.

Dismantling AC sheet roofing with ridge (corugated or semi corrugated)

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa with powder coating 150 gm /sqm as in roof covering /cladding to wall fixed with self tapping screws as specified

Dismantling of brick tiles single layer as in roof covering complete all as specified

Demolition of mud in roofs any thickness including leeping plaster (whether full thickness removed or only a part thereof) all as specified.

M & L for 50mm thick (average thickness) PCC padding of cement concrete type C-I (1:3:6) using 20mm graded crushed stone aggregate to bring top surface of slab in slope complete all as specified

Cleaning/Roughening surfaces of old concerete floor/roof by picking , sweeping clean and washing down with water to romove the dust etc complete all as spd.

M&L 10mm thick rendering on top of roof slab in cement mortar 1:4 by using water proofing compound @3% by the weight of cement, finishing the surface even and fair without using extra cement.

Providing and applying liquid Polyurea-PU based hybrid elastomeric water proofing membrane at existing/newly constructed roofs, RCC structure like basement raft, retaining wall, water retaining structure, tunnels/subways and bridge deck etc. in two or more coats. The product must have pot life of >90 mins., tensile strength > 12.6 Mpa, elongation of > 500% conforming to ASTM D 2370 & puncture resistance of >200 N as per ASTM E 154 with min. consumption of 1.5 Kg per sqm for 1.2mm DFT in two- three coats. The surface needs to be primed with water soluble self impregnated epoxy primer in two coats to be applied @ 200-250 gms/sqm/coat prior to Polyurea -PU application. Furthermor, (in case the substrate is not suitable) 15mm plaster is advisable for surface prepration before application of the water proofing membrane to avoid pinholes or functional difficulties of the system (Make - Asian Paints, BASF & SIKA) Note:- The application shall be done by the authorised applicator of the manufacture with a letter of proof stating the authenticity of the applicator firm.

S&F Corner Glass shelf with 2 racks with all accessories complete all as specified Make: Cera (Cat Part No:F5005201).

S&F Vitreous china wash hand basin 380 x 380 mm (Circle shape) under counter type bowl type including waste coupling and pipe all as specifed and directed. Make: Cera (Cat Part No: S2030133)

Demolition of reinforced cement concrete of any description and in any position complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 type B-1 using 20 mm graded aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Form work to soffits of suspended slabs such as roof slabs, floor slabs, shelves , landing and similar work not exceeding 200 mm thick (horzontal or sloping) and to edges of concrete complete all as specified and directed

M&L for 25 mm thick (Black) granite machine cut as in wash basin counters bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone laid over bedding layer or screed 15 mm thick in cement mortar 1:4 including cutting , grinding, rounding edges, rubbing and polishing complete all as complete all as specified and directed by Engr-in-Charge.

S&F in repairs stainless steel toilet paper holder with gutties and steel screws on walls as directed and approved complete all as specfied

S&F for brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges etc complete all as spd and directed.

S&F Towel Ring of CP fixed with and including chromium plated screws in repair complete all as specified.

S&F stainless steel soap dish complete all as specified.

Taking down carefully aluminium / copper point wiring (light / fan / socket or power) complete including fitting such as switches, ceiling roses, socket, light fittings, regulators etc complete and making good disturbed surfaces of walls, floors

Taking down main switch / DB as directed by Engineer-In-Charge.

Taking down unserviceable submain/ cable of any size as directed by Engineer-In-Charge.

M&L Point wiring complete with 1.5 Sq mm (nominal area) FRLS PVC insulated sheathed and stranded copper conductor cable ISI marked drawn into and including medium grade PVC conduit concealed (not less than 20 mm dia) all necessary fittings and accessories fixed concealed (including chase cutting in brick/stone masonery wall for fixing conduit and plastering the external surfaces and matching the same with existing suface) and pressed steel terminal boxes of thicknes not less than 1.2 mm for mounting fitting like P/T switches, sockets, lamp holders, sketch fittings and covered with 3 mm thick plastic laminated bakelite sheet cover fixed with brass screws and cup washers including one continuous run of FRLS PVC insulated green in colour 1.50 sqmm size copper conductor cable as earth wire and connected to common earth dolly complete all as specified and directed, are as follows :- (a) One light/one fan/one bell point controlled by one, one way switch.

(c) One socket outlet 5 pin 5 Amp controlled by one, one way switch on same board.

(d) One socket outlet 5 pin 5 Amp controlled by one, one way switch on independent board.

All as per item No. 102 here-in-before but wiring with using cable 2.50 sqmm size copper wire FRLS and earth wire of PVC insulated (Green colour) 2.50 Sqmm size copper wire for one 6 pin socket outlet, 16 Amperes on independent board.

Supply and fixing modular metal flush box 1/2 modular complete all as specified and directed.

Supply and fixing modular metal flush box 3 modular complete all as specified and directed.

Supply and fixing modular metal flush box 6 modular complete all as specified and directed.

Supply and fixing modular white cover plate with frame, 1/2 module complete all as specified and directed.

Supply and fixing modular white cover plate with frame, 3 module complete all as specified and directed.

Supply and fixing modular white cover plate with frame, 6 module complete all as specified and directed.

Supply and fixing modular Dummy plate complete all as specified and directed.

Supply & Fixing of switch modular switch one-way 6 Ampere module size complete all as specified and directed.

Supply and fixing of socket outlet 5 Ampere, 2 and 3 pins (TOTAL 05 PINS), 2 module AC complete all as specified and directed.

Supply & Fixing of switch modular switch 16 A one-way 16 Ampere module size complete all as specified and directed.

Supply and fixing of modular socket outlet two-in-one, 3/5 pin each module suitable for 5 and 16 Amperes module multi purpose type 2 module, AC complete all as specified and directed.

Supply and Fixing Ceiling rose, surface bakelite 3 terminal, 240 volts, 5 Amps with back plate of 3 mm thick bakelite, laminated hylem sheet of appropriate size, complete all as specified.

S & F lamp holder, PVC / polycarbonate type insulated body with back plate suitable for batten / angle fittings complete all as specified and directed.

Supply & Fixing MCB single pole, 240 volts, 6 to 32 Ampere, rupturing capacity 10 KA, ‘B’ curve type complete all as specified and directed.

S & F MCB SPN, 240 volts, 40 to 63 Ampere, rupturing capacity 10 KA, ‘B’ curve type complete all as specified and directed.

S & F sheet metal enclosure for DB’s (Double door type) when MCB’s to be used, single pole and neutral, 12 ways with 200 ampere rated bus bar, 240 volts fixed sunk / flush to the wall with IP-43 and IK-09 protection complete all as specified and directed.

Supply and fixing in replacement of LED tube light fitting for all purpose surface and wall mounted with single side connection polycarbonate LED batten with alumimium housing and integrated electronic driver of capacity 20 W , four feet and connection with PVC insulalted twin core 23/0.0076 twisted copper cable from ceiling rose to tube light fitting complete all as specified and directed.

S & F LED 9/10 Watt tube light 2 Feet mirror light fitting complete with all acessories 1x9 Watt LED , with CCT of 6000k suitable for domestic application, 240 Volts, 50 Hz, and internally pre-wired with 1.5 sqmm twin twisted flexible cable copper conductor and connection complete all as specified and directed.

Supply and fix in replacement of security light fitting LED 35 Watt with dusk and down sensor aluminum pressure dia cast housing with touched glass cover IP-66 protection Including suitable size GI Bracket and accessories complete mounted including connection with 3 core PVC insulated overall sheathed flexible cable with muyltistranded copper conductor of size not less than 1.0 sq mm from celing rose to fitting terminal including taking down old CFL security light fitting all as specified and as directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m Complete all specified and directed engr-in-charge

M & L for earthing complete with galvanised earth plate electrode 600 X 600 X 6 mm thick buried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of earth plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4 mm dia by means of nuts, bolts, check nuts & washers of galvanised iron or steel all as shown on electrical plate No. 3 of MES schedule 2009, Part – I (Specifications) and connected to main switch board / main DB’s / earthing test point including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust & common salt all around the earth plate minimum 150 mm in all directions with & including watering pipe 20 mm dia GI medium grade, GI funnel made out of 0.63 mm thick GI sheet, wire gauge, 50 mm thick RCC cover in PCC 1:2:4, type B-1, duly reinforced with 6 mm dia mild steel round bars @ 150 mm both ways center to center with suitable lifting handle to cover, earth pit of PCC 1:3:6 type C-1, GI protection pipe light grade 15 mm bore up to 7.5 m length from earth electrode & engraving of earth marking on nearby building with CM 1:4 plate size 200 X 150 X 15 mm & painting of earth result etc. including testing on complete all as specified and directed. Note :- On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor without any extra cost to Govt.

M & L for laying of LT cable of 1100 volt XLPE insulated and PVC sheathed of size 10 sqmm 2 core with cable gland including taking down old unserviceble cable complete all as specified and directed by Engineer-in-Charge. (For JCO/OR Md Accn)

Supply and lay burnt bricks sub class 'B' standard size laid across the cable in trenches as protection to the cable all as specified and directed.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.

Sanjiv Kumar (BID ID -3484344)