ADDN/ALTN TO CERTAIN OMQ AT AF STN CHANDIGARH UNDER GE (AF) CHANDIGARH.

Amount

Note :The unit rate quoted by the tenderer under Col No (13) of Sch `A’ (BOQ) unless specifically mentioned otherwise such as labour only/fixing only, for all items of works shall be deemed to be including cost of all materials, labour, tools and plants, testing and commissioning of work in position complete as required for entire completion of work.

Plain cement concrete ,25 mm average thickness (1:2:4) type B-0, using 12.5 mm graded mechanically crushed stone aggregates as in levelling course finished even & rough without using extra cement , complete all as specified and directed by Engineer-in-Charge.

Plain cement concrete 75 mm thick, 1:3:6, type C-2, using 40 mm graded mechanically crushed stone aggregates, laid in 1:20 slope as in plinth protection/court yard including making joints at 3.00 metre intervals and at each corner, the joint shall be filled with mastic filling (to full depth) comprising of one part heated hot blown bitumen 85/ 25 & two parts heated sand (by volume), surface finished even and fair in and including demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness (below or above ground level) and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge. Note :Quoted rates are inclusive of use and waste of formwork and to devide the area in panels.

Plain cement concrete 75 mm thick, (1:4:8), type D-2, using 40 mm graded mechanically crushed stone aggregates laid in 1:20 slope as in sub base ,foundations, filling and mass concrete/Plinth protection in and including demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness (below or above ground level) and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge. Note :Quoted rates are inclusive of use and waste of formwork and to devide the area in panels.

Brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement sand mortar 1:6 complete in and including demolition of brickwork or stone boulder masonary built in cement mortar including all quoins, arches, pillars etc for area where servicable bricks retrived and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge.

Demolition of reinforced cement concrete of any description & in any position and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge.

Use & waste of form work to soffits of suspended slab of concrete such as roof slabs, floor slabs, cover slab, shelve, landings and similar works n.exc 200 mm thick (horizontal or sloping); with rough finished surfaces of concrete, complete all as specified and directed by the Engineer in Charge.

Use & waste of form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floors and roofs n.exc. 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc. 10cm but n.exc. 20cm wide, with rough finished surfaces of concrete, complete all as specified and directed by the Engineer in Charge.

Mild steel TMT bars 10mm dia and over as in reinforcement cut to length , bent to shape required, including cranking, bending spirally for hooping ends for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.90mm dia, complete all as specified and directed by the Engineer in Charge.

Reinforced Cement concrete 1:2:4 type B-1, using 20 mm graded mechanically crushed stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the likes in and including demolition of reinforced cement concrete of any description & in any position and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge. Note: Steel reinforcement shall be measured and paid for separetely.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge.

First quality glazed ceramic coloured tiles of 450x300x7-8/600x300x 7-8 mm thick laid on vertical surfaces such as skirting, dados and risers to steps etc laid over and including 10mm thick cement plaster in CM (1:4) set and jointed in neat cement paste of honey like consistancy and pointed in white or coloured cement to match the shade of tiles ,complete all as specified and as directed by Engineer -in-Charge. Note : Design, pattern and colour of tiles will be as approved by GE.

First quality, Non skid ceramic coloured tiles, 7 to 8 mm thick joint free (square/ rectangular) area of each tile exceeding 0.11 Sq.m but not exceeding 0.18 Sq.m, laid in floors with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed of cement mortar (1:6) including pointing in white or coloured cement to match the shade of tiles ,complete all as specified and as directed by Engineer -in-Charge. Note :- Design, pattern and colour of tiles will be as approved by GE.

First quality, Non skid ceramic coloured tiles, 7 to 8 mm thick joint free (square/ rectangular) area of each tile exceeding 0.11 Sq.m but not exceeding 0.18 Sq.m, las in skirting, dados and risers to steps etc laid over and including 10mm thick cement plaster in CM (1:4) set and jointed in neat cement paste of honey like consistancy and pointed in white or coloured cement with pigment to match the shade of tiles , complete all as specified and directed by the Engineer in Charge. Note :- Design, pattern and colour of tiles will be as approved by GE.

Vitrified ceramic tiles (light Shade) 9 to 10 mm thick (square/ractangular) coloured polished tiles, area of each tile not exceeding 0.36 sqm laid in floors with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed of cement mortar (1:6) including pointing in white or coloured cement with pigment to match the shade of tiles ,complete all as specified and as directed by Engineer -in-Charge.

Vitrified ceramic tiles (light Shade) 9 to 10mm thick (square/ractangular) coloured polished tiles, area of each tile not exceeding 0.36 sqm as in skirting, dados and risers to steps etc laid over and including 10mm thick cement plaster in CM (1:4) set and jointed in neat cement paste of honey like consistancy and pointed in white or coloured cement with pigment to match the shade of tiles , complete all as specified and directed by the Engineer in Charge.

Demolition of stone slab and tiles of any description or thickness in floors, aprons etc, laid bedded and pointed in cement mortar and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushing neat cement slurry with 3.0kg of cement per sq. metre ,complete all as specified and as directed by Engineer -in-Charge.

Machine cut Mirror polished Kota stone slab flooring of 18-20 mm thick laid over 15mm thick screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab ,complete all as specified and as directed by Engineer -in-Charge. Notes :(i) Rate of kota stone flooring includes for all cutting and waste including machine cutting to make it square or rectangular. (ii) The quoted rate is inclusive for polishing by machine. (iii) Kota stone to be fixed in staircase Treader shall be of single piece.

Machine cut Kota stone slab of 18-20 mm thick as in risers of steps skirting, dado and pillar etc laid over 10mm thick cement plaster in CM (1:4) and jointed with grey cement slurry, mixed with pigment to match the shade of the slab including rubbing and polishing ,complete all as specified and as directed by Engineer -in-Charge. Notes :(i) Rate of kota stone flooring includes for all cutting and waste including machine cutting to make it square or rectangular. (ii) The quoted rate is inclusive for polishing by machine. (iii) Kota stone to be fixed in staircase Riser shall be of single piece.

Machine cut Kota stone slab of 18-20 mm thick as in landing etc laid over 10mm thick cement plaster in CM (1:4) and jointed with grey cement slurry, mixed with pigment to match the shade of the slab including rubbing and polishing ,complete all as specified and as directed by Engineer -in-Charge. Notes :(i) Rate of kota stone flooring includes for all cutting and waste including machine cutting to make it square or rectangular. (ii) The quoted rate is inclusive for polishing by machine. (iii) Kota stone to be fixed in Landing shall be of single piece.

Granite (of any type ) 16-18 mm thick, work (table rubbed and polished) fine grained 'Z' black/red in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including screed bed of 15 mm thick in CM 1:4 ,complete all as specified and as directed by Engineer -in-Charge.

Providing granite edge moulding to 18-20 mm thick stone of counters vanitiesetc; including machine polishing to edge to give high gloss finish ,complete all as specified and as directed by Engineer -in-Charge.

Ceramic outdoor heavy duty ultra designer tiles 300mm x 300mm x 15mm thick, factory made, ISI marked (IS 4457-2007), with grey cement & pigment, laid with neat cement slurry @ 3Kg/Sqm over & including 15mm thick screed bed of cement mortar (1:6), pointed in white cement with matching colour pigment in and including demolition of stone slab and tiles of any description or thickness in floors, aprons etc, laid bedded and pointed in white cement with pigment,complete all as specified and directed by Engineer-in- Charge.

Rendering 15 mm thick plaster on brick work or concrete external surfaces in cement mortar (1:6) , finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick on brick work or concrete internal surfaces in cement mortar 1:4 finished even and smooth without using extra cement in and including taking down cement plaster on brick walls & concrete surfaces & the like including raking out joints, hacking for key, scrubbing down with water etc., any description, and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge.

Rendering 10 mm thick in cement mortar (1:3), as on concrete surfaces (such as top & bittom of chajjas, beams, roof projection,balcony ,Mummty and stair case flight ceiling ,roof slab ceiling etc.) finished the surfcae even and smooth without using extra cement , complete all as specified and directed by Engineer-in-Charge. Notes for item No. 24,25 & 26: (i) Quoted rate shall be deemed to include for necessary scaffolding for building upto 9.00m high (Ground+1 storey building). (ii) All safety measures for the safety of workers shall be ensured by contractor before execution of work. Insurance of workers shall be got done by contractor before execution of the work and the cost for the same shall be deemed to be included in rate quoted by contractor.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer including 1mm thick wall care putty interior grade to smoothening the surface by using sand paper , complete all as specified and directed by Engineer-in-Charge.

Preparation of new plastered or unplastered surfaces of ceilings and filling the cracks/holes with cement wall care putty and applying two coats of oil bound distemper , complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment of internal surfaces of walls including brooming down or steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc; washing, rubbing down and stopping of surfaces using sand paper and applying two coat of oil bound distemper including 1mm thick Walll care putty and smoothing the surface, complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment of plastered surfaces of ceiling including brooming down or steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc; washing, rubbing down and stopping of surfaces using sand paper etc and filling the cracks/holes with cement wall care putty and applying two coats of oil bound distemper , complete all as specified and directed by Engineer-in-Charge.

Preparation of old painted steel or Iron surfaces over 10cm width or grith not otherwise described and applying one coat synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed by Engineer-in-Charge. Note For Ser Item No. 27 to 31:- The rates quoted against those items shall being to be included for the use of scafolding, ladders, cradles etc, up to triple storey building, removing nails, making good holes, cracks etc removing furnitures, cub boards, washing floors, floor and wall tiles,cleaning glasses, joinerys, electric fittings, wiring, conduits etc of drops, splashes and living premises clean and tidy upto entire satisfaction of Engineer-in-Charge,

Complete removal of existing treatment of old plastered /unplastered surfaces of walls by mechanically boomer and preparing plastered or unplastered old surfaces of walls including brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and filling the cracks/holes with wall care putty to rubbing down and stoping of surfaces using sand paper and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistance as per IS 15489: 2004, alkali & fungal resistant, dirt resistant exterior paint of required shade as approved with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm including 1mm thick Walll care putty and smoothing the surfacefor building upto Ground+1 storey high, complete all as specified and directed by Engineer-in-Charge.

Preparation of newly plastered /unplastered surfaces of walls and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistance as per IS 15489: 2004, alkali & fungal resistant, dirt resistant exterior paint of required shade (Company Depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm for building upto Ground+2 storey high, complete all as specified and directed by Engineer-in-Charge. Notes for item No. 29 to 30: (i).Weather proof exterior emulsion paint and primer shall be of same manufacturer. (ii)Quoted rate shall be deemed to include for necessary scaffolding for building upto Ground+1 storey high. (iii) All safety measures for the safety of workers shall be ensured by contractor before execution of work. Insurance of workers shall be got done by contractor before execution of the work and the cost for the same shall be deemed to be included in rate quoted by contractor.

Taking down Chowkhats with shutters without taking of shutter from the frame of any description not exceeding 1.50 Sq. m each, and making good the disturbed surface in CM 1:4 & finished with similar specification as exists, complete all as specified and as directed by the Engineer-in-Charge.

Taking down Chowkhats with shutters without taking of shutter from the frame of any description exceeding 1.50 Sq. m but not exceeding 4.00 Sq. m each, and making good the disturbed surface in CM 1:4 & finished with similar specification as exists, complete all as specified and as directed by the Engineer-in-Charge.

Pressed steel frames of size 105 x 60 mm, made out of 1.25mm thick sheet for doors with one or more rebates including necessary fixing lugs, hinges (mild steel butt hinges medium weight, cold rolled, 100 mm, ISI marked), lock strike plate, etc., including one shop coat of primer.with and including back filling PCC (1:3:6), type C-0,complete all as specified and directed by the Engineer in Charge. Note :Cost of filling hollow of frame with plain cement concrete shall be included in the quoted rate and nothing extra shall be admissible on this account .

Pressed steel frames of size 165 x 60 mm, made out of 1.25mm thick sheet for doors with one or more rebates including necessary fixing lugs, hinges (mild steel butt hinges medium weight, cold rolled, 100 mm, ISI marked), lock strike plate, etc., including one shop coat of primer.with and including back filling PCC (1:3:6), type C-0,complete all as specified and directed by the Engineer in Charge. Note :Cost of filling hollow of frame with plain cement concrete shall be included in the quoted rate and nothing extra shall be admissible on this account .

35 mm thick (Batten thickness) Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive wire cloth, glass etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, wire cloth etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats,complete all as specified and directed by the Engineer in Charge.

35 mm thick factory made Flush shutters ,solid core construction with block board core and plywood face panels commercial type on both sides, duly provided with 6mm thick Teakwood leeping on edges alround, fitted to chowkats, , complete all as specified and as directed by Engineer-in- Charge.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length , complete all as specified and directed by the Engineer in Charge. Note:M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately.

Factory made single extruded WPC (Wood Polymer Composite) solid plain door shutter of size 30 MM thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisturproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws ,complete all as specified and directed by Engineer-in- Charge. Note: stainless steel butt hinges and necessary S.S screws shall be paid separately.

Factory Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm in cupboard comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length, complete all as specified and directed by the Engineer in Charge.

Factory made single extruded WPC (Wood Polymer Composite) solid plain flush type as in shutter or exposed member of cupboard shutter of 18mm thick with Balancing on one face and wooden grain pattern lamonation on exposed surface with and including 18 mm wide 0.8 to 1 mm thick PVC leaping on exposed face to match with shade of shutter fixed with suitable solvent comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant, in and including dismantling of old board/Cup board shutter any description fixed in any postion with nails ,complete all as specified and directed by Engineer-in- Charge.

Aluminium powder coating (miniumum thickness of powder coating is 50 micron) work for chowkhat /shutters of doors, windows, ventilators, and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with equired EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed by Engineer -in-charge.

Aluminium powder coating (miniumum thickness of powder coating is 50 micron) for shutters of doors, shutters of openable/sliding windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed by Engineer -in-charge.

Butt hinges 25 mm size ,heavy duty, stainless steel hinges fixed with stainless steel screw ,complete all as specified and directed by the Engineer in Charge.

Butt hinges 100 mm size ,heavy duty, stainless steel hinges fixed with stainless steel screw ,complete all as specified and directed by the Engineer in Charge.

Barrel tower bolts aluminum anodizes of extuded section and fixed of 150 mm long size (length of bolt) , complete all as specified and directed by Engineer-in-Charge

Barrel tower bolts aluminum anodizes of extuded section and fixed of 125 mm long size (length of bolt) , complete all as specified and directed by Engineer-in-Charge

Handles 'D' type of size 150 mm ,extruded aluminium alloy , fabricated type anodized , complete all as specified and directed by Engineer-in-Charge

Handles 'D' type of size 125 mm ,extruded aluminium alloy , fabricated type anodized ,complete all as specified and directed by Engineer-in- Charge.

Aluminum alloy, anodized, sliding door bolt with hasp staple ( bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed length of bolt 250 mm, bolts not less than 12mm dia with and including a minimum of 6 bolts not,four on bolt plate and two on staple plate complete (ISI marked ) , complete all as specified and directed by Engineer-in-Charge

Continuous (Piano) hinges, width of flaps (when open ) 30mm, stainless steel bright finish or electro galvanised, ISI Marked ,complete all as specified and directed by Engineer-in- Charge.

Hasp & staple of 100mm size ,safety type aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws ,complete all as specified and directed by Engineer-in- Charge.

Magnetic catcher suitable for kitchen cabinet/ cup board with Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed,complete all as specified and directed by Engineer-in- Charge.

Cupboard knob 40mm dia, fixed with nut, washers / screws etc., of brass polished, bright finished,complete all as specified and directed by Engineer-in- Charge.

Small fittings of 2nd class HW such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles n exc 200 cu. cm each , complete all as specified and directed by Engineer-in-Charge

300mm long ordinary rat tail rod pattern MS door springs including roller and roller plate , complete all as specified and directed by Engineer-in-Charge

Sheet glass 4.8 mm thick, ordinary quality and glazing with oil putty or wooden bead in squares exceeding 0.5 Sq. m in each pane ,complete all as specified and directed by Engineer-in- Charge.

Figured glass 3 mm thick, pin headed tyoe and glazing with oil putty or wooden bead in squares not exceeding 0.5 Sq. m in each pane,including fixing with glass pins to hold glass in position ,complete all as specified and directed by Engineer-in- Charge.

Stainless, steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples or fixed to wooden bead , complete all as specified and directed by Engineer-in-Charge.

Framed work as in doors/Chowkhats or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete ( Fe-290,Gde-E-165), complete all as specified and directed by the Engineer-in-Charge.

M S work as Framed works such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes,framed guard bars barred iron doors ladders, framed balusters walk ways railing, framed work of water tanks, framed and hung as gates including pintle hinges, stops, hand made sliding sliding bolts etc ,drilling bolting or reveting etc and similar work conforming Fe-290 Gde E-165 ,complete all as specified and directed by Engineer-in- Charge.

Preparation of new or previously untreated wooden surfaces of any description , not otherwise described over 10 cm width or girth and applying two coats of synthetic enamells paint over one coat of pink primer ,complete all as specified and directed by the Engineer in Charge.

Preparation of new or previously untreated steel surfaces of any description , not otherwise described over 10 cm width or girth and applying two coats of synthetic enamells paint over one coat of red oxide primer,complete all as specified and directed by the Engineer in Charge.

Cutting chases, pinning in making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing and making good, cutting not exceeding 10cm girth, and removal of rubbbish outside MOD land,,complete all as specified and directed by Engineer-in- Charge.

Steel water tubing, 15 mm bore medium grade ISI Marked, galvanized with all fittings and fixed complete to walls, ceiling or laid in floors in and including taking up or down existing unservicable tubing and connections, cleaning for re fixing or removal to store, complete all as specified and directed by Engineer-in-Charge. Note: Fittings & specials as required shall be provided by the contractor. Contractor's rate shall be deemed to include the cost of fittings provided.

Steel water tubing, 20 mm bore medium grade ISI Marked , galvanized with all fittings and fixed complete to walls, ceiling or laid in floors in and including taking up or down existing unservicable tubing and connections, cleaning for re fixing or removal to store, complete all as specified and directed by Engineer-in-Charge. Note: Fittings & specials as required shall be provided by the contractor. Contractor's rate shall be deemed to include the cost of fittings provided.

Rotational moulded PVC, tripple layered, water storage tanks of capacity 500 litre (cylindrical vertical with closed top), ISI Marked, hoisted and fixed in position, with & including all fittings such as GI tank nipple etc. including Ball valve high pressure of PTMT with epoxy coated aluminium door and highdensity plastic ball screwed for 20mm dia iron pipe and fixed (minimum wieght 20mm 210gms )in and including dismantling PVC water tanks exc 251 ltr but n. exc 500 ltr capacity by disconnecting existing water connection and removal from site ,complete all as specified and directed by Engineer-in- Charge.

Stop cock regular body with flange, 15 mm bore fancy type chromium plated (concealed type) cast copper alloy, screwed down,high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed as in repair, complete all as specified and directed by Engineer-in-Charge.

Angle cock, 15 mm bore fancy type chromium plated cast copper alloy, screwed down,high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed as in repair, complete all as specified and directed by Engineer-in-Charge.

Bib cock long body with flange,15 mm bore fancy type cast copper alloy Chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed as in repair, complete all as specified and directed by Engineer-in-Charge.

Brass chromium plated shower rose 125mm with shower arm 15mm size, 195mm long with bend of 45 degree with flange including fixing to steel pipe or union fixed as in repair , complete all as specified and directed by the Engineer in -Charge. Note for Srl Item No 70 to 73:-The quoted rates against these items shall deemed to be included for replacement of damaged GI/Kitec fitting such as socket, elbow,nipple and tee of required size ,fitted/connected and making good any leakage. Nothing extra shall be admissible on this account.

Brass CP central hole basin mixer with 450mm braided connection pipe (without pop-up) for mixing hot & cold water for 15mm bore iron pipe and fixed as in repair, complete all as specified and directed by Engineer-in-Charge.

Sink mixer swan neck counter top ,15 mm bore of brass chromium plated for mixing hot & cold water screwed down for iron pipe for 15 mm bore pipe and fixed as in repair including making good the disturbed surfaces, complete all as specified and directed by the Engineer in -Charge.

Wall mixer with L bend (provision for over head shower), cast copper alloy, chromium plated for mixing hot and cold water, screwed down for 15mm bore iron pipe and fixed as in repair, complete all as specified and directed by Engineer-in-Charge.

Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed for 20 mm bore dia fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

Wash basins ,vitreous china, white,rectangular type of size 550x400mm including brackets and cutting for and pinning in ends of brackets or erecting stand 32mm dia Waste fittings, brass, chromium plated for glazed basins with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed inluding new brackets fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

Vitreous China wash down water closet pan (pedestal pattern), white with plastic seat cover (excluding fixing bolts, flushing cistern and flush pipe) including connection to trap,and to flushing pipe, anti-syphonage pipe,etc including 100mm cast iron 'P' or 'S' trap complete including making good to floor fixed as in repair , complete all as specified and directed by the Engineer in -Charge. Note :- Qty and Rates are inclusive of for both P type and S type Traps as on actual required basis on ground

PVC valveless , syphonic action type flushing cisterns 10 ltrs capacity , low level , white, with inlet ball valves , float and handle including brackets and pvc flush pipe 32 mm dia for low level fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

PVC connections 15mm size with PTMT nuts of length 600 mm fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

Hand shower (Health foucet) (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

Stainless steel chromium plated jet spray 15 mm dia pipe including with 1.25 metre long flexible tube and fixing arrangment including all accessories fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

PVC waste pipe flexible for Sink/ WHB of 32mm size fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

Soap dish brass, chromium plated fancy type fixed to plugs with chromium plated brass screws. fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Rectangular Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed with PVC rawl plugs and wooden screws fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Corner glass shelf of radius 300 mm including 02 Nos. metallic holding brackets, railing etc. fixed with PVC rawl plugs and wooden screws fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

CP grating 125 mm dia/hinged of brass and fixing with cement mortar 1:3 with/without holes as required fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Towel rail 600 mm long, 20 mm dia, ‘D’ type, brass chromium plated, fixed to walls with screws and plastic cleats fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

High density polyethylene (HDPE) pipes 40 mm dia of pressure rating 6 kgf/sq. cm fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Drapery rod of Stainless steel 25mm dia, fancy type, any shade, in and including set of fixing brackets, fixed to wall with stainless steel finols/finnels, connected accessaries, rubber packing, required screws and PVC rawal plugs as required fixed as in repair ,complete all as specified and directed by Engineer-in- Charge.

PVC (SWR) pipes 110 mm bore single socketed in any length with ruber rings joints fixed to walls with necessary brackets and making good the mouth of rain water pipe including taking down old pipes ,complete all as specified and directed by Engineer-in- Charge.

PVC (SWR) bends any radius 100mm bore fixed with solvent cement in any position as per site requirement , complete all as specified and directed by Engineer-in-Charge.

Cast iron soil, waste and vent pipe ,75 mm bore of spun pipe in any length with or without ears, with cement joints laid in trenches or wall in and including dismantling of cast iron work of any description,complete all as specified and directed by Engineer-in- Charge.

Cast iron soil, waste and vent pipe ,100 mm bore of spun cast pipes in any length with or without ears, with cement joints laid in trenches or wall in and including dismantling of cast iron work of any description,complete all as specified and directed by Engineer-in- Charge.

Cast iron bends 100mm dia bore, diminishing pieces or tapers ISI marked fixed as in repairs (larger bore measured) ,complete all as specified and directed by Engineer-in- Charge.

Cast iron cowel 75mm dia bore, ISI markedincluding jointing with solventin any postion as per site requirment fixed as in repairs,complete all as specified and directed by Engineer-in- Charge.

Cast iron branch pieces 75mm dia bore, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches ,reducers fixed as in repairs,complete all as specified and directed by Engineer-in- Charge.

Cast iron branch pieces 100mm dia bore, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches ,reducers fixed as in repairs,complete all as specified and directed by Engineer-in- Charge.

Cast iron floor trap, 75mm dia of out let, ISI marked, with stain less Steel grating, excluding jointing to waste pipe in Plain cement concrete (1:2:4) type B-1 fixed as in repairs,complete all as specified and directed by Engineer-in- Charge.

Cast iron floor trap, 100mm dia of out let, ISI marked, with stain less Steel grating, excluding jointing to waste pipe in Plain cement concrete (1:2:4) type B-1 fixed as in repairs ,complete all as specified and directed by Engineer-in- Charge.

Cast iron 'P' trap, 100mm alongwith SS grating dia including jointing with solvent cement in any position as per site requirment fixed as in repairs ,complete all as specified and directed by Engineer-in- Charge.

Dismantling the entire roof covering including brick tiles/ concrete tile of any thickness, mud phuska, mud plaster and water proofing treatment any number of layers or thickness etc. of any description upto RCC roof slab and cleaning the surface including flashings and junction of parapets, etc. with wire brushes and water to the entire satisfaction of Engineer-in-charge including removing the retrieved material to a place fixed by civic body and applying neat cement slurry @ 3.00 kg/ Sqm , complete all as specified and directed by Engineer-in-Charge. Notes:- (i) The quoted rate shall deemed to be included for necessary temporary arrangement of water supply from existing connection to toilets, bathrooms and kitchen for convenience of the occupants staying in quarters until completion of entire roof treatment and no any extra payment (ii) Dismantled material should be removed manually using stair all as directed by Engineer-in-Charge.

Plain cement concrete, 1:2:4) type B-0 , using 12.5 mm graded mechanically crushed stone aggregates as in roof kerb or mud stops in and including mixed with acrylic base liquid water proofing compound s per manufacturer’s instructions including all necessary formwork ,complete all as specified and directed by Engineer-in-Charge. Notes:-(i) Quoted Rate of above item is inclusive the cost of WPC and nothing extra shall be admissible on this account. (ii) Use and waste of form work shall deemed to be included in the quoted rate .

Plain Cement concretek type B-1, 1:2:4 by using 20mm graded mechanically crushed stone aggregate as in roof padding to maintain the required slope or to prepare gola etc icluding weathering slightly ropunded or chamfered angles and throating as directed in and including mixed with acrylic base liquid water proofing compound s per manufacturer’s instructions including necessary form work in and including demolition of (un-reinforced) cement concrete of any description or as roof padding and coveringg concrete in any position not otherwise specifically provided for and remove all the debris out of MoD land , complete all as specified and directed by Engineer-in-Charge. Notes:-(i) Quoted Rate of above item is inclusive the cost of WPC and nothing extra shall be admissible on this account. (ii) Use and waste of form work shall deemed to be included in the quoted rate . (iii) Contractor shall provide leveling bench mark at ridge level and up to edges with distances as specified by Engineer in Charge

Rendering 10 mm thick in cement mortar (1:4), as on fair faces of concrete surfaces (when concrete is green) finished the surfcae even and fair without using extra cement mixed with liquid water proofing compound as per manufacturer’s instructions, complete all as specified and directed by Engineer-in-Charge. Note:- Quoted Rate of above item is inclusive the cost of WPC and nothing extra shall be admissible on this account.

Preparation of newly plastered/RCC surfaces, making the surface completely dry and applying a coat of bitumen primer, having density in range of 0.87 to 0.89 kg/litre at 25 degree centigrade and viscosity of 70 to 160 CPS, manufactured by same manufacturer @ 0.4 ltr/sqm shall be applied and after drying of primer for 24 hours apply APP modified prefabricated water proofing membrane with non - woven polyster reinforcement, 3mm thick superior multipolymeric, weighing not less than 3.00 kg/sqm with properties of high penetration and centre core consisting of 90 micron high molecular high density polyetylene (MHHDPE) film consisting of five layers laid with torching application to the surface comeplete and sealing the side as well as end laps with torch (overlaps should not be less than 10cm in longitudinal direction and 15cm in traverse direction and shall be bonded with bitumen primer and levelled by heating the overlaps with brutane torch) , complete all as specified and directed by Engineer-in-Charge.

Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner ,complete all as specified and directed by Engineer-in- Charge.

Uprooting completely natural vegetation/ plants, stems of trees (upto 30cm girth) grown up on walls, parapets or in roof or any part of building upto 10 metre (Ground +2 storey) and making good the damaged/ disturbed portion and filling holes in cement mortar (1:3) or PCC (1:2:4) type B-0 using graded crushed stone aggregate to match with the existing surface , complete all as specified and directed by Engineer-in-Charge.

Plain Cement concrete type B-0, 1:2:4 by using 12.5 mm graded mechanically crushed stone aggregate as in sunken portion or similar items as in filling in and including demolition of lime concrete/lean concrete/brick bats from sunken portion exc. 15cm thickness (above ground level) in and including removing of debris away from site to a designated point fixed by local administration out side of MOD land , complete all as specified and directed by the Engineer in Charge .

Broken brick or boulders aggregate not exc 63mm deposited spread and levelled in layers not exc 15mm thick watered and rammed to a true surface in sunken portion or similar items as in filling in and including demolition of lime concrete/lean concrete/brick bats from sunken portion exc. 15cm thickness (above ground level) in and including removing of debris away from site to a designated point fixed by local administration out side of MOD land , complete all as specified and directed by the Engineer in Charge .

Steel water tubing, 50 mm bore medium grade ISI Marked , galvanized as in Spout for sunken floor, fixed as in wall with inside end fixed with wire netting and external end bevelled edge at 45 degree, complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick in cement mortar (1:4), as on fair faces of brick or concrete surfaces (sunken portion)finished the surfcae even and smooth without using extra cement mixed with liquid water proofing compound as per manufacturer’s instructions, complete all as specified and directed by Engineer-in-Charge. Note:- Quoted Rate of above item is inclusive the cost of WPC and nothing extra shall be admissible on this account.

Applying two coats of two component elastomeric acrylic polymer modified cementtitious waterproofing coat ng, smartcare Ultra block 2K or equivalent, having 215% elongation as per ASTMD-2370, resisting 5 bars hyrostatic pressure as per DIN 1048, Crack briding upto 3.50mm as per EN 1062-7 and sprinkling dry fine sand over wet second coating compelete, as per manufactures specifications ,complete all as specified and directed by Engineer-in- Charge. Note : Unless otherwise recommended by manufacturer, the mixing ratio of the components shall be 6 part of powder and 4 parts of liquid without any water addition in the mixing etc.

Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240, complete all as specified and directed by the Engineer-in-Charge.

Pre-colour coated high tensile strength galvalume sheet roofing with yield strength (550 NPA) prepainted with aluminium (55%) and zinc (45%) alloy coating applied through continous hot dip process having tatal coated thickness (TCT) of 0.50mm with minimum coating mass on both sides @ 150gms/sqm in length and width as per site condition fixed with complete acessories as per manufacturer's instructions through specialist agency and as per profile and shade as approved by GE ,complete all as specified and directed by Engineer-in-Charge.

Mild steel, plain, black of sheet of 1 mm thick iheet in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required , complete all as specified and directed by Engineer-in-Charge.

Wall mounted Kitchen Utensils dish rack stainless steel (31x10x30 inches) as approved by GE, complete all as specified and directed by Engineer-in-Charge.

Dismantling of existing kitchen cabinet of any type and descripition and "Supplying and fixing factory made modular kitchen as per the drg and as per legend att and brief details given below (Details for one set of kitchen for Sqn Ldr /Non Status Qtr):- 1. Modular kitchen shall be provided with box type cabinets boxes, drawers, utensil units and other details with size and specification, acessories as given below : (A) Drawer below cocking platform (2.96Mx0.70Mx0.60M-01 No):- (i) Pot and pen Unit (ii) Premium qlty basket (iii) bottle pull out (iv) Cutlary (vi) Gas Cylender Holder (vii) Multy perpose Draw (vii) Grain Tray (atta/rice) (B)Cabinet above kitchen platform- .20Mx0.70Mx0.30M(02Nos):- (i) Multy purpose cabin with movable glass self. (C) Drawer below Sink - 2.51Mx0.8Mx0.6M (01 No) :- (i) Multy purpose cabin with movable glass self (ii) Detergen Holder (iii) Dust bin holder (iv) SS Soundless double bowl square Sink

2. Brief Specification of Kitchen :- (a) For Exposed member of cabinet:- Kitchen Factory made single extruded WPC (Wood Polymer Composite) solid plain flush type as in shutter or exposed member of cabinet structure of 18mm thick with Balancing on one face and wooden grain pattern lamonation on exposed surface with wide 0.8 to 1 mm thick PVC leaping on exposed face to match with shade of shutter fixed with suitable solvent comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and 18 MM . (b) Cabinet frame Shelf and other members same as ser No (a) above but 18mm thick Lamination/Balancing on both side. (c) Back member of cabinet structure:- single extruded WPC (Wood Polymer Composite) solid plain flush type as in back member of cabinet structure of 06 mm thick with Balancing on both surfaces comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant

(d) All untensil units/drawers with inner fitting provided as per manufacture (e) Stainless Steel Sink shall be double square soundless of thickness not less than 1.00mm thick with each kitchen including waste coupling and waste pipe etc. 3 . Accessories :- The following Accessories of best quality of make as approved shall be provided with qty as required for each unit as mentioned above against para A, B & C :- (a) Pot and Pan (Hettich) (b) Pipe lift up (c) BPO (ss with telescopic channels) (d) PVC Adjustable Legs (e) Hydraulic Hinges (Hettich) (f) Dustbin Holder (g) Detergent Holder (h) Cutlery (Hettich) (600mm) (j) Cellpin -45 (k) Lights Below Upper Boxes. (l) WPC Edge bending tape 0.8mm will will apply on overall kitchen shutter and boxes. (m) Ground profile handleless (on each unit below slab) (n) Upper boxes shutter will be handleless with extended length of 20mm. 4. Total area of Elevation as mentioned in para A, B & C for modular kitchen is 60.02Sqft. Notes : 1. Contractor will prepared working drgs as per plan att for modular kitchen all as mentioned above and get approved by GE 2. Any accessories/fittings not specified above if required for modular kitchen fuctioning shall be provided by the contractor without any extra cost.

Taking down carefully aluminium/ copper point wiring (light/ fan/ socket/ power) complete (fittings such as switches, sockets, ceiling roses pendants, regulators, sockets, light fitting etc. to be measured separately), removing materials to store for keeping in safe custody or for taking credit as per Schedule of credit including making good disturbed surfaces of walls, floors etc. , complete all as specified and directed by Engineer-in-Charge.

Point wiring for one light point/Fan point controlled by one switch one way drawn through and including non metalic rigid PVC conduit medium duty of 20 mm dia or higher concealed type with all strandard fittings such as Tee junction, bends etc ,using FRLS PVC unsheathed multistrand copper conductor cable of 1.5 sqmm single core and fixing on Modular Metal flush box alongwith Modular White cover plate with frame of suitable module for earth continuity insulated PVC unsheathed(green colour) 1.5 sqmm copper earth wire connected to common earth dolly ,complete all as specified and as directed by Engineer-in- Charge. Notes :(i) Wiring shall be done by using proper colour coding. (ii) Modular Metal flush box and Modular White cover plate with frame of shall be measured and paid seperately.

All as per srl item No. 122 here-in-before but for 05 Amp socket outlet on independent board, with cables 1.5 sqmm., complete all as specified and directed by Engineer-in-Charge. Notes :(i) Wiring shall be done by using proper colour coding. (ii) Modular Metal flush box and Modular White cover plate with frame of shall be measured and paid seperately.

All as per srl item No. 122 here-in-before but for One 3 pin socket outlet 5 amps on the same board with other switches, with cables 1.5 sqmm., complete all as specified and directed by Engineer-in-Charge. Notes :(i) Wiring shall be done by using proper colour coding. (ii) Modular Metal flush box and Modular White cover plate with frame of shall be measured and paid seperately.

Point wiring for one light point controlled by two switchs two way drawn through and including non metalic rigid PVC conduit medium duty of 20 mm dia or higher concealed type with all strandard fittings such as Tee junction, bends etc ,using FRLS PVC unsheathed multistrand copper conductor cable of 1.5 sqmm single core and fixing on Modular Metal flush box alongwith Modular White cover plate with frame of suitable module for earth continuity insulated PVC unsheathed(green colour) 1.5 sqmm copper earth wire connected to common earth dolly ,complete all as specified and as directed by Engineer-in- Charge. Notes :(i) Wiring shall be done by using proper colour coding. (ii) Modular Metal flush box and Modular White cover plate with frame of shall be measured and paid seperately.

Point wiring for one Bell point controlled by one switch one way drawn through and including non metalic rigid PVC conduit medium duty of 20 mm dia or higher concealed type with all strandard fittings such as Tee junction, bends etc ,using FRLS PVC unsheathed multistrand copper conductor cable of 1.5 sqmm single core and fixing on Modular Metal flush box alongwith Modular White cover plate with frame of suitable module for earth continuity insulated PVC unsheathed(green colour) 1.5 sqmm copper earth wire connected to common earth dolly ,complete all as specified and as directed by Engineer-in- Charge. Notes :(i) Wiring shall be done by using proper colour coding. (ii) Modular Metal flush box and Modular White cover plate with frame of shall be measured and paid seperately.

Point wiring for 15 Amps socket point controlled by one, one way switch using drawn through and including non metalic rigid PVC conduit medium duty of of 20 mm dia or higher with all strandard fittings such as Tee junction, bends etc ,using FRLS PVC unsheathed multistrand copper conductor cable of 2.5 sqmm single core and fixing on Modular Metal flush box alongwith Modular White cover plate with frame of suitable module for earth continuity insulated PVC unsheathed(green colour) 2.5 sqmm copper earth wire connected to common earth dolly ,complete all as specified and as directed by Engineer-in- Charge. Notes :(i) Wiring shall be done by using proper colour coding. (ii) Modular Metal flush box and Modular White cover plate with frame of shall be measured and paid seperately.

Modular switch 1 way 6 A, 1 module ,complete all as specified and as directed by Engineer-in- Charge.

Modular socket outlet, 2/ 3 pins combined, 6 Amps, 2 module, 230 volts ,complete all as specified and as directed by Engineer-in- Charge.

Modular switch 1 way 16 A, 1 module ,complete all as specified and as directed by Engineer-in- Charge.

Modular socket outlet, 6/ 16 Amps, 2/3 pin combined, 230 volts, 2 module ,complete all as specified and as directed by Engineer-in- Charge.

Modular switch 2 way 6 A, 1 module ,complete all as specified and as directed by Engineer-in- Charge.

Modular Bell push 6 A, 1 module ,complete all as specified and as directed by Engineer-in- Charge.

Ceiling Rose, 3 Phase/ PVC/ Polycarbonate, isolated body, complete all as specified and directed by Engineer-in-Charge.

Ceiling fan regulator step type Modular of 120 watt ,2 module for 1200/1400 mm sweep ceiling fan and connecting up fixed as in replacment ,complete all as specified and directed by Engineer-in- Charge.

Lamp holder insulated body with back plate suitable for batten fittings with LED bulb 07 watt ,complete all as specified and directed by Engineer-in- Charge.

Buzzer, Ding Dong AC. 230 volts,single pole ,complete all as specified and directed by Engineer-in- Charge.

MCB SP, 6 to 40 Amps, ,240 Volts ,10 KA 'B' curve type to be housed in DBs of Proper and suitable size cable lugs to be fixed with MCBs fixed as in replacment ,complete all as specified and directed by Engineer-in- Charge.

MCB SPN, 40 to 63 Amps, ,240 Volts ,10 KA 'C' curve type to be housed in DBs of Proper and suitable size cable lugs to be fixed with MCBs fixed as in replacment ,complete all as specified and directed by Engineer-in- Charge.

Distribution box Double door type , SPN 12 way,with 200 amps rated bus bar, 240 Volts 50 HZ for MCBs, grouted flush to walls complete with IP 65 and metal double door ,epoxy powder coated fixed as in replacment ,complete all as specified and directed by Engineer-in- Charge.

Sheet metal enclosure factory made single pole & neutral with a two pin & earth plug and socket etc complete with provision for one single pole 'B' series MCB 20 Amps 240 volts ,complete all as specified and directed by Engineer-in- Charge.

LED Lights fittings 1x18watt 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed by Engineer-in-Charge.

LED light fitting 1x9W/1x10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed by Engineer-in-Charge.

LED light fitting mirror type with high out put diffuser 2ft, 10watt 220v AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed by Engineer-in-Charge.

Wall mounted fittings with ABS housing and clear polycarbonate cover including retrofit LED bulb 7/9 watt and connecting up with three core flexible copper conductor cable of 0.5 sqmm size from ceiling rose, complete all as specified and directed by Engineer-in-Charge.

Exhaust fan, steel body AC single phase 230v of size 300mm sweep 50 HZ ,1200RPM copper windening with blades, frames and louvers, complete all as specified and directed by Engineer-in-Charge.

Exhaust fan, made of sturdy Engineering plastic complete with louvers shutter AC single phase 230v of size 250mm sweep ,copper windening including hole for fixing exhaust fan , complete all as specified and directed by Engineer-in-Charge.

Modular Metal flush box 1/2 module ,complete all as specified and directed by Engineer-in- Charge.

Modular Metal flush box 3 module ,complete all as specified and directed by Engineer-in- Charge.

Modular Metal flush box 4 module ,complete all as specified and directed by Engineer-in- Charge.

Modular Metal flush box 6 module ,complete all as specified and directed by Engineer-in- Charge.

Modular Metal flush box 8 module ,complete all as specified and directed by Engineer-in- Charge.

Modular White cover plate with frame,2 module ,complete all as specified and directed by Engineer-in- Charge.

Modular White cover plate with frame,3 module ,complete all as specified and directed by Engineer-in- Charge.

Modular White cover plate with frame,4 module ,complete all as specified and directed by Engineer-in- Charge.

Modular White cover plate with frame,6 module ,complete all as specified and directed by Engineer-in- Charge.

Modular White cover plate with frame,8 module ,complete all as specified and directed by Engineer-in- Charge.

Modular White Blanking Plate , 1 module ,complete all as specified and directed by Engineer-in- Charge.

Sub main wiring with two single core 4.0 Sqmm FRLS PVC insulated and unsheathed 1100 volts grade cables with stranded copper conductor cable drawn through in and including 25 mm dia rigid non metallic PVC conduit and conduit accessories including one single core 4.0 Sqmm FRLS PVC insulated unsheathed stranded copper earth cable connected to common earth dully wiring for security light connection from junction box to security light in and including taking down carefully copper/Aluminium submain wiring of any size/core/type complete including conduits/casing caping etc, removing the materials/debris and making good the disturbed surfaces of wall, floors and ceiling etc. to match with the original existing finishcomplete all as specified and directed by Engineer-in-Charge. Note : (i) 2 run of 4.0 Sqmm ,1 run of PVC conduit & 1 run of 4.0 Sqmm cable will be measured as single run. (ii) Extra length of cables/wire required for connection to MCBs shall not be measured and paid separetly the rate quoted by contractor per unit shall be deemed to be included in the quoted rate of this item.

Sub main wiring with two single core 6.0 Sqmm FRLS PVC insulated and unsheathed 1100 volts grade cables with stranded copper conductor cable drawn through in and including 25 mm dia rigid non metallic PVC conduit and conduit accessories including one single core 6.0 Sqmm FRLS PVC insulated unsheathed stranded copper earth cable connected to common earth dully wiring for security light connection from junction box to security light in and including taking down carefully copper/Aluminium submain wiring of any size/core/type complete including conduits/casing caping etc, removing the materials/debris and making good the disturbed surfaces of wall, floors and ceiling etc. to match with the original existing finishcomplete all as specified and directed by Engineer-in-Charge. Note : (i) 2 run of 6.0 Sqmm ,1 run of PVC conduit & 1 run of 6.0 Sqmm cable will be measured as single run. (ii) Extra length of cables/wire required for connection to MCBs shall not be measured and paid separetly the rate quoted by contractor per unit shall be deemed to be included in the quoted rate of this item.

Earthing complete with GI earth plate electrode of size 600mm x 600mm x 6mm thick buried directly in ground vertically with top edge of earth plate not less than 1.5m below normal ground level (depth of pit not less than 2.25m below normal ground level), earth plate surrounded from all sides by 15cm thick packed alternate layers of charcoal dust and common salt, electrode connections using galvanized iron wire of 4mm dia (8 SWG) by means of GI bolts, nuts, check nuts & GI washers and other end of earth lead connected to main switch board or main control board or test point or equipment, earth lead protected by galvanized iron pipe light grade (ISI marked) 20mm bore, alongwith watering pipe 20mm bore GI medium grade (ISI marked of specified make), funnel with wire mesh including all necessary excavation & earth work, PCC chamber in PCC (1:2:4) type B-1 and RCC cover all as shown in electrical plate No 3 of MES Schedule Part-I including testing on completion in and including taking out old unservicable earthing , complete all as specified and directed by Engineer-in-Charge. Notes:- (i) Pit cover shall be 80mm thick pre-cast of RCC (1:1½:3) type A-1 reinforced with XPM not less than 4Kg/ Sqm. (ii) PCC Chamber shall be constructed 500mm away from the edge of earth pit. (iii) Rate shall include earth lead and protection pipe of length 7.5m, excess beyond 7.5m length required at site shall be measured and paid separately. (iv) Earth resistance should be less than 5 Ohm. In case the test results are not found below 3 Ohm, complete earthing will be redone without any extra cost to Govt.

Fixing only light fitting any type/ Capacity obtained from item No 121 above,complete all as specified and directed by Engineer-in- Charge.

Taking down fan, sealing cable end,dismantling blades and removing fans and blades to store ,complete all as specified and directed by Engineer-in- Charge.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan obtained from item No 163 above,complete all as specified and directed by Engineer-in- Charge.

Hanging only Exhaust fan and connecting up including provision of cable from ceiling rose or connector to fan obtained from item No 163 above,complete all as specified and directed by Engineer-in- Charge.

Note :Schedule of credit to be deducted on acceptances of bid.Details of Schedule of credit is given in tender documentse.

Dhillon Construction Company (BID ID -3409512)

MOHAMMAD RASHID (BID ID -3401811)

B N FRIENDS AND CO (BID ID -3401137)

Baba Engineers and Contractors (BID ID -3401835)

M/S MATLOOB AHMED (BID ID -3409201)