8863/E8

Amount

Demolition Brick Work built in Cement Mortar including all Quoins, Arches, Pillars, etc, but excluding Ashlar Facings, dressed Stone Work and Pre-cast Concrete Articles of any descriptions, complete all as specified and as directed.

Taking down shutters of any description exc. 1.00 Sqm but n.exc 2 Sqm each and removing from site or to store as directed by Engineer in charge.

Taking down PVC shutters with PVC chowkhat including all fittings exc. 1.00 Sqm but n.exc 2 Sqm each and removing from site or to store as directed by Engineer in charge.

Taking down chowkats or frames with shutter (without taking off shutter from the frames) exc. 1.50 Sqm and n.exc 4 Sqm each complete all as specified and directed.

Taking down Cement Plaster of any description on Brick Walls, Concrete Surfaces including racking out joints, hacking for key, scrubbing down with Water, remove dust, debris/ rubbish, etc., complete all as specified and as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing), and removing rubbish off the Premises, complete all as specified and as directed.

Dismantling Timber Fillets, Rails, Posts, Rafters, Purlings, etc., under 40 Sqcm in Section, in any Position, as in unframed Work, complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

M&L Plain Cement Concrete 1:2:4 type B-1 (20 mm graded crushed stone aggregate) as in Holdfast Block including necessary form-work, etc., complete all as specified and as directed.

M&L Brick work with fly ash bricks designation 75 (kgf/cm2) straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed.

M&L Brick Work pulverized fly ash bricks ,Half-Brick thick, Old Size, built in Cement Mortar 1:4, Straight or Curved on Plan to any Radius, complete all as specified and as directed.

Cutting chase, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of laddings, steps, cills, sushades, shelves, lintels etc and cutting chase for concealed water tubing or concealed coduit wiring etc and making good cutting grith n exc 10 cm on brick walls complete all as specified and directed.

M&L Cutting Holes in Brick Walls, built in Cement Mortar for Taking Out or Inserting Holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1as required in exc. Half Brick but not exc. One Brick thick Walls, complete all as specified and as directed.

M&L Second Class Hardwood Plain Fillets sqaure, rectangular or triangular in section wrought, secured with Nails, cross sectional area exc 6.0 Sqcm but not exc. 13.0 Sqcm, complete all as specified and as directed.

M&L Second Class Hardwood Plain Fillets sqaure, rectangular or triangular in section Wrought, secured with Nails, cross sectional area exc13.0 Sqcm but not exc. 25.0 Sqcm, complete all as specified and as directed.

S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, fixing in opening as per Specifications and Drawings shown in MES Schedule Part-II, complete all as specified and as directed.

S&F Plain Colour Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing etc complete all as specified and as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules ofelasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: (1) For WPC solid door/window frames, minus 5mmtolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. (2) (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

S&F Factory Made Solid PVC Moulded Door Shutter With Wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site complete all as specified and directed.

S&F Second Class Hardwood Plain, Solid, Straight Chowkats and Frames, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue, Pinned at Joints, complete all as specified and as directed.

S&F for 2nd class hardwood 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats as specified in SSR Part-I 2009.complete all as specified and directed.

M&L Second Class Hardwood 35mm thick Plain Framed Panelled Door Shutter (any Number of Panels) with Panel of 12mm thick BWP Commercial Ply or Veneered Particle Board with commercial face veneers on both faces and fitted to Wooden Chowkat, complete all as specified and as directed.

S&F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to chowkhats complete all as specified and directed.

S&F Mild Steel Butt Hinges, size of Hinges 100mm, medium weight, Cold Rolled and fixed, complete all as specified and as directed

S&F in repair Mild Steel Butt Hinges, size of Hinges 100mm, medium weight, Cold Rolled and fixed, complete all as specified and as directed

S&F Aluminum anodized, barrel tower bolts of extruded section, 200 mm long and fixed with steel screws complete all as specified and directed.

S&F in repair Aluminum anodized, barrel tower bolts of extruded section, 200 mm long and fixed with steel screws complete all as specified and directed.

S&F Aluminum alloy Handle 150mm long, Extruded Section, Fabricated type, anodized and fixed, complete all as specified and as directed.

S&F in repair Aluminum alloy Handle 150mm long, Extruded Section, Fabricated type, anodized and fixed, complete all as specified and as directed.

S&F 250 mm long Aluminum alloy, anodized, Sliding Door Bolt with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminum alloy and fixed, complete all as specified and as directed.

S&F in repair 250 mm long Aluminum alloy, anodized, Sliding Door Bolt with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminum alloy and fixed, complete all as specified and as directed.

S&F Floor door stopper of steel body and overall length of cover plate 150 mm and tongue anodised with hard drawn steel spring as in repair complete all as specified and directed.

S&F in repairs cup board knobs 40 mm size with all fixing screw etc complete all as specifeid & directed.

S&F in repair Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and as directed.

S&F in repair stainless steel piano hinges fixed with screw on cupboard/door/window etc complete all as directed.

S&F 20 mm dia Fancy type, Chromium Plated colour coated ( any coloured) curtain rod fixed to bracket/ pelmet box complete all as specified and as directed.

S&F Chromium plated Bracket for curtain rod in any size complete all as specified and as directed.

S&F MS as in Holdfast Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified and as directed.

S&F in repair Powder coated anodised aluminium sliding fly proofing window, three tier (two shutter of glass and one shutter on wire mesh) without glazing bar, window shutter style shall be 40mm X 19mm, sheet thickness 1.5mm ,sliding channel 3mm htick channel width shall be as required and directed by Engr-in-Charge with roller. Frame (Chowkats) of window shall be 75mm X 60mm X 1.5mm thick section with or without rebate with 5.5mm thick tinted glass and galvanised wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18mm aluminum glazing clips fixed with rubber gasket locking arrangement all as directed by Engr-in-Charge.

S&F Aluminium ventilator with powder coated anodized aluminium frame of section size 65.5 x 38.10 x 1.5 mm and Shutter with section 47.62mm x 44.5mm x 1.5mm thick half portion fixed with glass and half portion louvered including powder coated alunimium anodised “D” handle, hinges, peg stays, tower bolt etc including jointing cleats for fixing Builder hardware complete all as specified & directed.

M&L Prelaminated particle board 18/19mm thick as in cup board shutter and Shelf, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame works as in repair complete all as specified and as directed.

M&L for Repairs to any type of wooden joinery works of shutters, shelf etc such as door, window, Ventilator,cupboards of any description in any situation by taking down & refixing in the same opening including Resecuring,easing, adjusting ,refixing builders hardware butt hinges,tower bolts,handles,sliding door bolts,rat tail,lock,ball catches,knobs,hasp & staple,peg set,door stopper,piano hinges,door cill strip etc wiremess,glass pane in same/other position,renewal of screws,welding (if required) etc,wooden beading & tightening of GI/steel wiremesh etc making smooth functioning (for proper closing ,opening) etc with entire satisfaction of Engineer-in-charge complete all as specified and directed

M&L Non-skid Ceramic Coloured Tiles, 7.0mm to 8.0mm thick (square/rectangular), area of each tile exc 0.06 sqm but not exc 0.11 sqm in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over 15mm thick screed bed (1:6) in cement mortar complete all as specified and as directed.

M&L Non-skid Ceramic Coloured Tiles, 7.0mm to 8.0mm thick (square/rectangular), area of each tile exc 0.11 sqm but not exc 0.18 sqm in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over 15mm thick screed bed (1:6) in cement mortar complete all as specified and as directed.

M&L Vitrified Ceramic Tiles 8-9 mm thick (square/ rectangular) in dark Shade, Polished, area of each tile not exc 0.36 sqm as in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over 20mm thick screed bed in cement sand mortar (1:6) complete all as specified and as directed.

M&L glazed ceramic coloured tiles 450x300x6-7mm in vertical surfaces set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L Granite (of any type) Work (Table rubbed and polished) 18 to 20 mm thick, in Steps, Cooking Platforms and like, Set in Screed bed of 20mm thick in Cement Mortar 1:4 including Pointing in White Cement 1:2 using Marble Dust with admixture of Pigment to match with Shade of Granite including Cutting and Polishing including half round edges, including demolition of old tiles/surface complete all as specified and as directed.

M&L Green Marble Work 18 mm to 20mm thick (Table rubbed and polished) in border of kota stone flooring and like, Set in Screed bed of 20mm thick in Cement Mortar 1:4 including Pointing in White Cement 1:2 using Marble Dust with admixture of Pigment to match with Shade of Marble including Cutting and Polishing, including demolition of old flooring complete all as specified and as directed.

M&L as in patch repair Non-skid Ceramic Coloured Tiles, 7.0mm to 8.0mm thick (square/rectangular), area of each tile exc 0.11 sqm but not exc 0.18 sqm in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over 15mm thick screed bed (1:6) in cement mortar including demolition of old tiles complete all as specified and as directed.

M&L as in patch repair Non-skid Ceramic Coloured Tiles, 7.0mm to 8.0mm thick (square/rectangular), area of each tile exc 0.11 sqm but not exc 0.18 sqm in Vertical surfaces such as skirting, dados etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over 10mm thick screed bed (1:4) in cement mortar including demolition of old tiles complete all as specified and as directed.

M&L for cleaning of floor and wall existing surfaces,sanitary fittings etc with the help of harpic/Roff/Lizol brand chemical or equivalent complete all as specified and directed.

M&L for 5 mm thick rendering not exceeding 3sqmeach patch on fair surface on brick or concrete surfaces of wall in CM 1:3 and finished even and smooth without using extra cement complete all as specified & directed.

M&L Rendering 15mm thick in Cement Mortar 1:6 not exceeding 3sqmeach patch on fair surface on Brick Walls or on Concrete Surfaces, finishing plastered surfaces Even and smooth without using Extra Cement complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:6 on Brick Walls or on Concrete Surfaces, finishing plastered surfaces Even and fair complete all as specified and as directed.

M&L Preparing old decorated Plaster Surfaces of ceiling and applying One Coat of oil bound distemper (any colour /tint) complete all as specified and as directed.

Material and labour for preparation of existing old wall surface and applying one coat of oil bound distemper (any colour/tint) on wall surfaces complete all as specified and directed.

M&L for Preparation of new plastered surfaces and applying two coats of oil emulsion distemper (any colour/tint) over a coat of primer over 2 mm thick wall care putty on ceiling surfaces including rubbing with emmery paper to make surface smooth and even complete all as specified and directed.

M&L for Preparation of new plastered surfaces and applying two coats of oil emulsion distemper (any colour/tint) over a coat of primer over 2 mm thick wall care putty (Birla/Asian) on wall surfaces including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed.

M&L for complete removal of existing finishes and treating with two coats of oil bound distemper (any colour/tint) over a coat of Chalk whiting, over 2mm thick wall care putty including rubbing with emmery paper to make wall surface smooth and even complete all as directed and specified.

M&L for preparation of old plastered surface and applying one coats of weather proof exterior emulsion paint over a coat of primer with approved colour and pattern complete all as directed and specified

S&F Sheet Glass 3.0mm thick ordinary quality glazing with Wooden Beads or Oil Putty in Square or Rectangular, not exc. 0.50 Sqm, complete all as specified and as directed.

S&F Figured Glass 4.0mm thick, Pin Head / frosted type and glazing with Wooden Beads or Oil Putty in Square or Rectangular, not exc. 0.50 Sqm, complete all as specified and as directed.

S & F in repair, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including if required fixing with wooden beads or MS flat of size 15mmx3mm & chromium plates screws/using metal nut and bolts or wooden beading,aluminium window fittings,neoprine rubber gasket etc if required including necessary scaffolding up to twelve storeys height of bldgs complete all as specified and directed

M&L Preparing old Wooden Surfaces of any description not otherwise decribed over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and as directed.

M&L Preparing old Steel Surfaces of any description not otherwise decribed over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and as directed.

M&L for Preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel plaint over a coat of red oxide all as specified and directed by Engineer-in-Charge.

Supply and Laying Steel Water Tubing 15mm Bore (dia), Galvanised, ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation, including taking down old unserviceable tubes and deposit to store complete as all specified and as directed.

Supply and Laying Steel Water Tubing 20mm Bore (dia), Galvanised, ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation, including taking down old unserviceable tubes and deposit to store complete as all specified and as directed.

Supply and Laying Steel Water Tubing 25mm Bore (dia), Galvanised, ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation, including taking down old unserviceable tubes and deposit to store complete as all specified and as directed.

M&L for taking down and refixing of old Steel Water Tubing 15mm Bore (dia), and connections with all new Fittings such as bends, elbows, tees, short pieces, connectors, back nut, reducer, diminishing pieces, caps, unions and plugs etc but except Steel tube connection, in new or old position such as fixed on Walls, Ceiling or laid in Floors or any other Situation, cleaning the same or deposit to store complete as all specified and as directed.

M&L for taking down and refixing of old Steel Water Tubing 20mm Bore (dia), and connections with all new Fittings such as bends, elbows, tees, short pieces, connectors, back nut, reducer, diminishing pieces, caps, unions and plugs etc but except Steel tube connection, in new or old position such as fixed on Walls, Ceiling or laid in Floors or any other Situation, cleaning the same or deposit to store complete as all specified and as directed.

M&L for taking down and refixing of old Steel Water Tubing 25mm Bore (dia), and connections with all new Fittings such as bends, elbows, tees, short pieces, connectors, back nut, reducer, diminishing pieces, caps, unions and plugs etc but except Steel tube connection, in new or old position such as fixed on Walls, Ceiling or laid in Floors or any other Situation, cleaning the same or deposit to store complete as all specified and as directed.

Supply and fix 40 mm dia PVC pipe with bend complete fixed on walls, ceilings and floors including GI/PVC clamps, bends sockets etc incl taking down unservicable old PVC pipes complete all as specified and directed.

S&F work in repair for 20mm outer dia of CPVC water tubes SDR 11 with all fittings SDR 11 and fixed complete to walls and ceilings or laid in floors including taking down of old pipe complete all as specified and directed

S&F 20mm bore brass MTA for CPVC pipe as in repair complete all as specified and directed.

S&F 20mm bore brass FTA for CPVC pipe as in repair complete all as specified and directed.

S&F 20mm bore brass elbow for CPVC pipe as in repair complete all as specified and directed.

S&F 20mm bore brass Tee for CPVC pipe as in repair complete all as specified and directed.

S&F 20mm bore dia of pipe Ball valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball screwed for iron pipe and fixed as in repair complete all as specified and directed.

Supply and fix Gun metal, globe or gate valves (ISI marked) ( Class-I) with iron wheel head, screwed both ends for 20 mm bore GI pipe including taking down old unserviceable one complete as specified and as directed

S&F Bip tap with nozzle 15mm bore standard of PTMT any colour screwed for iron pipe & fixed (min. weight15mm-95 gms) as in repair complete all as specified and directed.

S&F Stop valve 15mm bore of PTMT any colour screwed for iron pipe & fixed. (min. weight 15mm-90gms) with PTMT flange as in repair complete all as specified and directed.

S&F 32mm bore PVC waste pipe flexible type including all cups and sockets with minimum length 800mm for any type/make/size for stainless steel sinks, basins,urinal etc as in repair complete all as specified and directed.

S&F 32 mm dia Flush pipe of low/high density polyethylene pipe as directed including jointing to any type of WC and any type/size/make of low level flushing cistern and make good dismantle floor to match the existing surfaceas in repair complete all as specified and directed.

S&F Cast Iron Nahani/ floor Trap with 100mm bore (dia) Outlet, with Gratings including jointing to Waste Pipe and fixed in Cement Concrete 1:2:4 (20mm graded aggregate), as in repair complete all as specified and as directed.

S&F PVC connection pipe 15mm size with PTMT nuts of length 600mm long as in repair complete all as specified and directed.

S&F in repair CP connector for hot water supply of size 600 fixed to 15 mm GI pipe complete all as specified and directed.

S&F in repair PVC (SWR) Soil, Waste and Ventilating Pipe 110mm bore (dia), single socketed, in any length with Rubber Ring Joints fixed to Walls, complete all as specified and as directed.

S&F in repair PVC (SWR) Soil, Waste and Ventilating Pipe 75mm bore (dia), single socketed, in any length with Rubber Ring Joints fixed to Walls, complete all as specified and as directed.

S&F in repair PVC (SWR) Bend 110mm bore (dia), any type, and Jointing with Solvent Cement, complete all as specified and as directed.

S&F in repair PVC (SWR) Bend 75mm bore (dia), any type, and Jointing with Solvent Cement, complete all as specified and as directed.

S&F in repair PVC (SWR) Junction 110mm bore (dia), Single (Single T) equal or unequal and Jointing with Solvent Cement, complete all as specified and as directed.

S&F in repair PVC (SWR) Junction 75mm bore (dia), Single (Single T) equal or unequal and Jointing with Solvent Cement, complete all as specified and as directed.

S&F in repair UPVC (SWR) 110mm bore Branch pieces, double (equal or unqual), ordinary or inverted (spigot or socket type) or with parallel branches or fitted with oval access doors and Jointing with Solvent Cement complete all as specified and directed.

S&F in repair UPVC (SWR) 75mm bore Branch pieces, double (equal or unqual), ordinary or inverted (spigot or socket type) or with parallel branches or fitted with oval access doors and Jointing with Solvent Cement complete all as specified and directed.

S&F Stack clamps out of 50mm by 5mm flat iron and 16mm dia bolt round iron stays including bolts and nuts and securing ends of stays to wall or roof Bore in pipe in 75mm to 150mm complete all as specified and directed.

S & F in repair PVC tank lid/cover for water storage tank capacity of 250 to 2000 ltrs to matching with existing tank with fixing arrangement complete all as specified and directed.

S & F in repair 100mm dia stainless steel grating with hole/without hole for waste pipe fixed over floor/nahani trap complete all as specified and directed

Disconnecting existing tanks of capacity exc 250 & not exc 2000 liters setting aside (or lowering, hoisting if required) for repairs & scrubbing cleaning, thoroughly removing all scale and dirt, mud sediments, silts etc from the internal surfaces of PVC/RCC water storage tanks (bottom and wall) by using brushes, bleaching powder and other cleaning materials as required and removing vegetation/ Algae around the over head tank after opening tank cover, inlet, outlet etc and reconnecting with GI/CPVC tubing and re-fixing in position , refixing the cover after cleaning all and specified and directed. Note: While cleaning Any CI/GI/PVC pipes and fittings, Float valve damaged during work shall be replaced by new one to insure leakage / seepage free joint without any extra cost to the department and Unit rate quoted by tenderer shall includ for use of all scaffolding, protective measures etc up to twelve storeys height of bldgs.

S&F Rotational Moulded Polyethylene (HDPE) Water Storage Tank 500Litre Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I including provision of 25mm x 100mm GI nippples with check nuts for inlet, outlet wash, float valve and overflow pipealongwith PTMT Ball Valve 20mm dia , high pressure with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe including Lowering of old/unserviceable Water Storage Tank of any description, complete all as specified and as directed.

S&F Rotational Moulded Polyethylene (HDPE) Water Storage Tank 1000Litre Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I including provision of 25mm x 100mm GI nippples with check nuts for inlet, outlet wash, float valve and overflow pipealongwith PTMT Ball Valve 20mm dia , high pressure with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe including Lowering of old/unserviceable Water Storage Tank of any description, complete all as specified and as directed.

S&F Rotational Moulded Polyethylene (HDPE) Water Storage Tank 2000Litre Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I including provision of 25mm x 100mm GI nippples with check nuts for inlet, outlet wash, float valve and overflow pipealongwith PTMT Ball Valve 20mm dia , high pressure with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe including Lowering of old/unserviceable Water Storage Tank of any description, complete all as specified and as directed.

S&F Stainless Steel Sink with Drainage Board l.0mm thick Overall size 915mm x 460mm and Bowl size 410 mm x 355 mm x 165 mm for Kitchen or Laboratory with Plugs, Washers, Brass chromium plated Waste Fitting 32mm dia, PVC waste pipe, a Pair of Cast Iron Brackets duly Painted including Cutting and Pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 including Taking down/out unserviceable Sink and connected Items, complete all as specified and as directed.

S&F in repairs Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm etc incl 40mm dia waste pipe complete including taking down/out unserviceable Sink and connected Items, complete all as specified and as directed.

S&F in repair stainless steel utencil plate rack of size 900 x 1200 x 200 mm using 1.0mm thick sheet with all fittings accessories complete as directed.

S&F Vitreous China Colour Wash down Water Closet Pan (Pedestal Pattern) with "p" or "s" trap front or back inlet including fixing Bolts with and excluding low level Flushing Cistern matching with water closet colour with inlet ball valve float handle and providing 32mm dia PVC flush pipe including plastic water closet seat with flat bottom cover (coloured) fixed with mild steel chromium plated or aluminium hinging device including taking down old unserviceable one complete all as specified and as directed.

S&F Vitreous China, semi-pedestal pattern (Anglo-Indian Type) with "p" or "s" trap front or back inlet including fixing Bolts with and excluding Flushing Cistern matching with water closet colour with inlet ball valve float handle and providing 32mm dia PVC flush pipe including plastic water closet seat with flat bottom cover (coloured) fixed with mild steel chromium plated or aluminium hinging device including taking down old unserviceable one complete all as specified and as directed.

S&F in replacement Vitreous China White Squatting Pan ‘ORISSA’ Pattern, size 580x440mm with ‘P’ or ‘S’ Trap, Integral Foot Rest, providing Joints between Flush Pipe and Socket of WC Pan including Flushing Cistern and Flush Pipe, fixing with and including provision of cement Concrete Bedding complete all as specified and as directed.

Supply and fixing in repair 10 litre capacity low level PVC flushing cistern (any colour), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete as directed.

S&F PVC bathroom cabinet box with mirror, shutter type of size 500X400 fixed on walls with wooden plugs and and chromium plated brass screw and cup washer as in repair complete all as specified & directed.

S&F EWC Cascade type (coloured) floor mounted water closet with low level flushing cistern coloured with floor trap, PVC coloured seat cover and connecting pipe etc and making all necessary connections etc as in repair complete all as specified and as directed.

S&F in repair only cascade/concealed type flushing cistern including cleaning and replacing of washers, syphon inlet accessory with complete fittings and fixtures etc all as directed in day to day maintenance.

S&F in repairs Plastic seat cover white for EWC with flat bottom incl hinging device complete all as specified & directed.

S&F Chromium plated bottle trap ( with internl partitions) 32mm size with 250mm long wall connection including wall flange fixed in position with necessary fixing arrangement as in repair complete all as specified and directed.

S&F Chromium Plated waste coupling heavy full thread 32mm (brass) fixed to stainless steel sink including necessary fixing arrangement as in repair complete all as specified and directed.

S&F Vitreous China Wash Hand Basin 550x400mm in size, White (Flat Back or Angle Back Type) with 32mm dia Brass Chromium Plated Waste Fitting, a pair of Cast Iron Brackets duly painted including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 including taking down/out unserviceable Wash Hand Basin and connected Items, complete all as specified and as directed.

S&F in repair fancy type bib cock 15 mm bore cast copper alloy chromium plated with crutch or butterfly handle screwed for iron pipe brass ferrule etc. complete all as specified & directed

S&F Two way bib cock with flange brass chromium plated fancy type screwed for 15 mm bore etc.as in repair complete all as specified and as directed.

S&F Angular Stop cock concealed type ,15 mm dia cast copper alloy chromium plated fancy type with wall flange screwed for iron pipe etc. as in repair complete all as specified and directed.

S&F 125 mm dia brass chromium plated shower rose with or without swivels joint for fixing to 15 mm bore pipe etc complete including taking down old one complete all as specified and directed.

S&F Brass chromium plated fancy type stop cock screwed for 15 mm bore of pipe etc.incl necessary fittings & fixtures as in repair complete all as specified & directed.

S&F Brass chromium plated fancy type pillar tap screwed for 15 mm bore of pipe etc.incl necessary fittings & fixtures as in repair complete all as specified & directed.

S&F Towel ring of size 150mm dia decorative type fixed with walls including necessary fittings etc as in repair complete all as specified and as directed.

S&F Brass chromium plated tubular towel rail, 20mm dia, D type, 60,cm long between flanges as in repair complete all as specified and directed.

S&F Toilet paper holder of brass chromium plated fixed to walls with chromium plated brass screw including necessary fixing arrangement as in repair complete all as specified and directed.

S&F Chromium Plated soap dish fixed to wall with necessary fixing arrangement as in repair complete all as specified and directed

S&F Glass shelf assembly consisting of 5.5 mm thick sheet glass self 19-12 cm wide, 60 cm long with chromium plated brackets guard and railing fixed in position with necessary fixing arrangement as in repair complete all as specified and directed.

S&F Glass corner shelf of single set with chromium plated brackets and railing including necessary fittings and fixture as in repair complete all as specified and directed.

S&F Central hole for Hot and Cold water supply basin mixer, brass chromium plated screwed down for iron pipes,including necessary fittings etc as in repair , complete all as specified and as directed.

S&F 3-in-1 wall mixer for Hot & Cold water supply with telephonic shower arrarengement, brass chromium plated fancy type, screwed down for 15mm bore iron pipe incl necessary fittings & fixtures etc.as in repair complete all as specified and directed.

S&F CP Kitchen sink mixture with regular swinging spout (wall mounted model) chromium plated screwed down for iron pipes,including necessary fittings etc as in repair complete all as specified and as directed.

S&F health faucet with chomium plated with flexible cord fixed on wall screwed down for iron pipes,including necessary fittings etc as in repair complete all as specified and as directed.

(i) M&L Preparing Masonary surfaces cracks, large pores, dents or damaged portion with smart care crack seal. (II) M&L Applying two coats of smart care damp block 2K slurry by brush or roller over brick masonary surfaces,Allow 1st coat to dry for 4-6 hrs and then apply 2nd coat . (III) Applying a coat of 2mm thick acrylic wall putty (Make JK/Asian/Birla) (VI) Applying a coat of interior wall primer after smoothing wall putty surfaces with sand paper and two coat of acrylic oil bound distemper complete all as specified & directed. Note : Mixing of smart care damp block 2k , 60% powder and 40% liquid and use mechenaically stirrer

M&L for complete removal of damage plastered surfaces by mechanical means using electrical operated grinder, washing down and any kind of damage painted surfaces and old plastered surfaces of wall (II) Preparing unplastered surfaces cracks, large pores, dents or damaged portion with smart care crack seal. (III) Applying two coats of smart care hydroloc without any dilution with paint brush @ 7Sqm/Ltr and allow it to dry for 6-8 hrs after first coat. (IV)Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished the surfaces even and smooth without using extra cement (V) Applying a coat of 2mm thick acrylic wall putty (Make JK/Asian/Birla) (VI) Applying a coat of interior wall primer after smoothing wall putty surfaces with sand paper and two coat of acrylic oil bound distemper complete all as specified & directed.

Cleaning of blocked kitchen trap / nahani trap / floor trap/ Water closet of any type / pattern with vaccum pump upto 1st manhole and making the drain channel fully functional by flushing with sufficient quantity of water to entire satisfaction of Engineer-in-Charge including cleaning of 1st manhole and removing the waste materials / sludge etc to a distance outside residential area and burying the same in a pit and spreading bleeching powder surrounding the area @ 1Kg/ Sqm and sealing the top with fine sand of suitable depth complete all as specified and as directed. Note:-(i) Cost of earth work in excavation required for digging the borrow pit and burrying the the waste materials / sludge in the borrow pit and sealing the pit with fine sand and spreadind of bleeching powder shall deemed to be included in the rate quoted. (ii) Any damged done by the Contractor during cleaning shall be make good by the Contractor at his own cost upto the satisfaction of Enginner-in-Charge.

Cleaning of under rain water / waste pipe of any dia by rodding / bamboo split including removing and refixing of eye cover in exesting positiob and taking out waste and foreign materials and flushing with sufficient quantity of water etc. and cutting of the bushes both side of sewage line upto 0.5 mtr each side and throwing the waste materials into non residential area or near by drain / nallahand including cutting the bushes surrounding the sewage line upto 0.50m complete all as specified and as directed. Note:-(i) Once cleaned the sewage lines, the Contractor shall maintain the lines functional upto the date of Completion at his own cost. (ii) Any damged done by the Contractor during cleaning shall be make good by the Contractor at his own cost upto the satisfaction of Enginner-in-Charge.

Taking down existing broken inspection eye cover from soil/waste/rain water pipe from any height any position and supply and fix new CI eye cover with rubber washer and nut bolts for 100/75 mm dia pipe incl necessary scaffolding and safety measurers complete all as directed by Engineer-in-Charge.

M&L in repairs for leaking water in brass/CP bib tap, pillar tap, concealed stop cock, angle valve of any make/ description/size in any position by replacing the (brass spindle+brass jumper washer) ,tightening of fittings etc ,also removing air lock, blockage in water pipe line of size 15 mm & make the all system fully functional to the entire satisfaction of Engr-in-Charge complete all as specified and directed

M&L in repairs for leaking water in brass/CP bib tap, pillar tap, concealed stop cock, angle valve of any make/ description/size in any position by replacing the (brass spindle+brass jumper washer) ,tightening of fittings etc ,also removing air lock, blockage in water pipe line of size 20 mm & make the all system fully functional to the entire satisfaction of Engr-in-Charge complete all as specified and directed

M&L in repairs for leaking water in brass/CP bib tap, pillar tap, concealed stop cock, angle valve of any make/ description/size in any position by replacing the (brass spindle+brass jumper washer) ,tightening of fittings etc ,also removing air lock, blockage in water pipe line of size 25 mm & make the all system fully functional to the entire satisfaction of Engr-in-Charge complete all as specified and directed

M&L for Repair for joint leakage in steel water tube by replacing of GI elbow/socket/reducers/nipple/union/bend/tee of any length 15mm bore medium grade ISI mark of complete all as directed.

M&L for Repair for joint leakage in steel water tube by replacing of GI elbow/socket/reducers/nipple/union/bend/tee of any length 20mm bore medium grade ISI mark of complete all as directed.

M&L for Repair for joint leakage in steel water tube by replacing of GI elbow/socket/reducers/nipple/union/bend/tee of any length 25mm bore medium grade ISI mark of complete all as directed. Notes for item No.142.00 to 144.00: 1. Unit rate quoted by tenderer shall included for use of all scaffolding, trestles, ladders, cradles etc, hoisting, lowering and protective measures etc up to four storeys height of bldgs being external works of building. 2. Cost of taking down steel water tube & refixing old steel water tube and connection in new or old position with new fixing arrangment in walls, ceiling, floors etc Shall be included in the rates quoted by the contractor.

M&L in repairs for leaking water in brass/CP bib tap, pillar tap, concealed stop cock, angle valve of any make/ description/size in any position by replacing the (brass spindle+brass jumper washer) ,tightening of fittings etc ,also removing air lock, blockage in water pipe line & make the all system fully functional to the entire satisfaction of Engr-in-Charge complete all as specified and directed

M&L in repairs for (PVC Syphon assembly (internal kit) for any type/size/make of low level flushing cistern,tightening of fittings etc & make the all system fully functional to the entire satisfaction of Engr-in-Charge complete all as specified and directed.

M&L in repairs for leaking water in brass/CP Wall Mixer, basin mixer, sink mixer of any make/ description/size in any position by replacing the brass spindle & washer, tightening of fittings etc ,also removing air lock, blockage in water pipe line & make the all system fully functional to the entire satisfaction of Engr-in-Charge complete all as specified and directed

M&L for Repairs to any type of Aluminium Doors, AluminiumWindows, Aluminium Ventilators, Aluminium Louvers, Aluminium CB shutters etc of any description, in any situation by taking down & refixing shutter including replacement of rubber neoprene packing, aluminum snap beading, screws & tightening, adjustment etc ,making smooth functioning (proper closing, opening) etc with entire satisfaction of Engineer-in-charge complete all as specified and directed.

M&L for Petty repairs to wardrobes, cupboard, kitchen cabinet, Showcase items of any description in any situation including Resecuring,easening of shutters, shelf etc including taking down and refixing in position with new nut, screw ,washer etc including adjusting, tightening of builders hardware such as lock,wiremess,glass pane, Ball catches, knobs ,hasp and staple ,piano hinges,handles & refixing builders hardware in same/other position making smooth functioning (proper closing, opening) etc with entire satisfaction of Engineer-incharge complete all as specified and directed

Cutting/uprooting of tree from walls of bldgs. up to extended root and spraying of acid of required qty at any location of bldg up to 4 storied & making good disturbed surfaces with CM 1:4 or cement concrete (1:3:6) type C1 using 20mm graded aggregate including necessary scaffolding/ through rope with safety belt for size of tree of girth 5 to 10 cm complete all as specified and as directed by Engr -in-charge.

M&L for 32 x 6mm aluminium strip burried in ground/fixed on wall ,roofwith saddles and fixing screws etc., for roof conductors and down conductors above ground including taking down existing unserviceable/worn out complete all as specified and as directed

M&L for Air termination,single pointed Al rod 12mm dia and 300mm long including taking down existing unserviceable/worn out complete all as specified and as directed

M&L for Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm,drilled and screwed including 3nos 8mm dia 25mm long hex. Head screw including taking down existing unserviceable/worn out complete all as specified and as directed by engineer in charge.

M&L for PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation base of poles and other similar locations including demoltion of old PCC/broken PCC complete all as specified and as directed by the Engr-in-Charge.

M&L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate with and including all necessary form work complete all as specified & directed.including demoltion of old PCC/broken PCC

Supply and fix PVC cable terminal boxes, outdoor type of size 155mm x210mm x92mm with MCB SP 6 to 32 Amps including all necessary fittings and connection including taking down old unserviceable one complete all as directed by Enginner-in-Charge.

Supply and fix PVC cable terminal boxes, outdoor type of size 93mm x93mm x62mm including fixing with clamp including taking down old unserviceable one complete all as directed by Enginner-in-Charge.

Taking out unserviceable street light of any type and any sizes from the site of work complete all as specified and directed.

Supply and fix LED decorative post top lantern, 35/40 Watt capacity for energy efficient conservation upto 50% and with eco friendly lighting system with all accessories and necessary connection including taking down old unserviceable one complete all as specified and as directed.

Supply and fix LED IP65 rated inverted Pyramid Tripod type, LED Bollard 10/8 Watt capacity with soft 360° light distribution with all accessories and necessary connection including taking down old unserviceable one complete all as specified and as directed.

Supply and fix Pressure die cast powder coated housing with PC diffuser efficient high output LED bollard light cylindrical shaped 9/10 watt capacity IP 65 protection including necessary connection and taking down old unserviceable one complete all as specified and as directed.

S & F LED 12 Watt IP 67 rating waterproof fountain light compact and robust design with aluminum housing, waterproof connectors with colour white/ RGB/ mono RGB with all accessories and necessary connection including taking down old unserviceable one complete all as specified and as directed.

Supply and fix LED bollard light cylindrical shaped 9/10 watt capacity Pressure die cast powder coated housing with PC diffuser. Efficient high output LED with IP65 protection including necessary connection and taking down old unserviceable one complete all as specified and as directed.

Supply and drawn into the steel tubular pole, by drilling holes just above the junction box and another holes near street light brackets including inserting PVC insulated stranded copper electric cable of size 2.5 sqmm 2 core & all necessary connetions with junction box and street light fittings, complete all as specified and as directed. Note:- Junction box and street light fittings shall be measured and paid saperately under relavent item of BOQ/ Sch 'A'.

Supply and fixing LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

Supply and fixing LED street light fitting 90 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

Supply and fixing LED street light fitting 120 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

Supply and fixing LED flood light 80watts 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant including taking down old unserviceable one complete all as specified and as directed.

Supply and fixing LED flood light 50watts 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp including taking down old unserviceable one complete all as specified and as directed.

Taking out unserviceable steel poles of any type and any sizes from the site of work complete all as specified and directed.

M & L steel tubular sewaged pole 9 mtr long completed with MS base plate, finial taper plug nut bolts, screws as specified type 410 SP-31 as per relevant IS specifiecation including two coats of aluminimum paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge. Note : Earth work/excavation PCC shall be measured and paid seperately.

M & L for Scraping, cleaning and preparation of surface of all steel tubular sewaged pole 9 mtr long, cross arms, clamps GI street light bracket etc and applying two coat of aluminium paint including writing pole number & bottom of pole painted with black paint with yellow strip allround between the juction of aluminium paint and black paint complete as directed and specified.

BHARUKA ENTERPRISES (BID ID -3484585)

PINKY CO. (BID ID -3485234)

RADHA ENTERPRISE (BID ID -3485414)

M/S H.P Singha (BID ID -3484470)

M/S BISWANATH BHATTACHARJEE (BID ID -3483678)

RBS Builders (BID ID -3483587)

ARJUN DAS VALECHA (BID ID -3486903)

UNIVERSAL TRADING CENTRE (BID ID -3486059)