REHABILITATION OF TEMPORARY BUILDINGS INCLUDING GALVALUME SHEET, FALSE CEILING AND ALLIED ITEMS AT POONCH LINE AND LALE DA BAGH AT DAMANA UNDER GE JAMMU

Amount

Dismanting asbestos cement (corrugated or semicorrugated etc) sheets in roof covering complete all as specified and as directed.

Material and labour for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Material and labour for pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Dismantling timber scantling 40 Sq cm and over in section framed work of any description complete all as specified and as directed.

Supply and fixing for structural steel works of Fe-410W (Grade 'E' 250) quality 'A', as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. including painted one shop coat of zinc chromate / red oxide primer paint (including preparation of surface) before fabrication complete all as specified and as directed.

Supply and fixing plates (plain or chequered channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed.

Material and labour for mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exceeding 22.5 cm and not exceeding 30 cm long, diameter of neck 16mm to 20mm complete all as specified and as directed. Make:- Conforming to IS

Material and labour for precast cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in blocks for hold fasts, benching, coping apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed. Note: - Form work required for these items included in the unit rate of this item.

Dismantling boarding of any description including frame work fixed in any position with nail complete all as specified and as directed.

Supply and fixing for frame work for ceiling with specification as under mentioned: - (i) GI section frame work (Powder coated) for white, pre-premiered, self embossed, reinforced designer board consisting of perimeter wall angle 19mm X 19mm X 0.45mm, cross 'Tee' 28.6mm (web) X 24mm flange 0.33mm thick powdered coated main tee 38mm (Web) X 24mm flange 0.33mm thick. Wall angle shall be screwed / fixed to brick wall / partition wall / concrete / RCC with the help of nylon sleeves and screws @ 610 mm centre to centre, then suspending GI main 'Tee' in both directions by means of hangers with alignment @ 1220 mm centre to centre to soffits. To from grid of 610 X 610mm cross Tee shall be provided @ 610mm centre to centre in both directions and all suitable provisions shall be made for fixing the recessed / surface mounting light fittings if any, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for 4mm thick of size 605 X 605 mm, white pre-premiered, self embossed, reinforced designer board for false ceiling conforming to IS-14862 and ISO-8336 : 1993 fixed / laid / inserted to GI framework at ceiling with screws complete all as specified and directed.

Demolition of brick work built in cement mortar including all quoins, pillars, arches etc including precast cement concrete benching / coping etc complete all as specified and as directed.

Material and labour for brick work with sub class 'B' bricks straight or curved on plan exceeding 6 m mean radius built in cement mortar (1:6) complete all as specified and as directed.

Description all as per Ser Item No 13.00 here-in-before except bricks complete all as specified and as directed.

Material and labour for reinforced cement concrete (nominal mix) (1:2:4) in type B-1 (using 20mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span, as in lintel band complete all as specified and as directed.

Use and waste of form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floors and roofs not exceeding 20 cm wide and sides of RCC / PCC bands in walls, horizontal or sloping and similar work exceeding 10 cm but not exceeding 20 cm wide for rough finished surfaces complete all as specified and as directed by Engineer-in-Charge.

Material and labour for steel reinforcement TMT bars 10 mm dia and over cut to length, bent to shape and tying with annealed mild steel wire 0.9mm dia complete all as specified and directed.

Description all as per Ser Item No 17.00 here-in-before but 5mm dia and over upto and including 10 mm dia as in binders, stirrups, spacer complete all as specified and as directed.

Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubbing down with water and removing unserviceable material outside cantt area complete all as specified and directed by Engineer-in-Charge. Note: - Plaster work may be in patches upto triple storey.

Material and labour for rendering 10 mm thick in cement mortar (1:6) on fair faces of brick surface finished even and smooth without using extra cement upto height of four storey building complete all as specified and as directed.

Material and labour for rendering 15 mm thick in cement mortar (1:4) on other than fair faces of brick surface finished even and smooth without using extra cement etc. complete all as specified and as directed. (Including all necessary scaffolding, lifiting arrangement for external surfaces).

Material and labour for two coats of oil bound distemper to newly plastered surfaces including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

Material and labour for applying two coats of cement based paint including preparation of newly plastered surface complete all as specified and as directed.

Material and labour for complete removal of existing treatment of old surface of wall (plastered or unplastered) and applying one coat of cement based paint complete all as specified and as directed.

Material and labour for applying one coat of oil bound distemper of wall to old plastered surfaces including preparation of surfaces complete all as specified and directed.

Material and labour for applying one coat of synthetic enamel paint on old steel surfaces of any description not otherwise described over 10 cm width or girth including preparation of old surface complete all as specified and directed.

Material and labour for applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces of any description not otherwise described over 10 cm width or girth including preparation of surface complete all as specified and as directed.

NOTE NO 1: - Samples of materials as approved will be kept in GE's sample room. NOTE NO 2: - All fittings and fixtures mentioned above will be fixed to the satisfaction of Engr-in-Charge and GE. NOTE NO 3: - Warranty certificate to the Engineer-in-Charge where ever applicable shall be submitted by the Contractor at the time of fittings.

STAR CONSTRUCTIONS

Mehta Enterprises

M/S KARAN SINGH CONTRACTOR

bushan kumar

M/s Koul & Sons

M/S Raman Construction Co.

M/S MOHAN LAL GUPTA

BALVINDER SINGH AND SONS

Bidder Name

M/S Raman Construction Co.

STAR CONSTRUCTIONS

Mukesh Construction Co.

M/S MOHAN LAL GUPTA

BALVINDER SINGH AND SONS

M/s Koul & Sons

bushan kumar

Mehta Enterprises

M/S KARAN SINGH CONTRACTOR