SPECIAL REPAIR TO OR MD ACCN BLDG P-20/5 TO 20/12 AT JADUNATH ENCLAVE AND 01 X UNDERGROUND ROOM AT FCAB AT NAMS

Amount

Taking down chowkats or frames with shutter’s (without taking off shutter’s from frame) n.exc 1.50 sqm each all as specified and directed.

Taking down chowkats or frames with shutter’s (without taking off shutter’s from frame) exc 1.50 Sqm & nxc 4.00 Sqm each all as specified and directed.

Taking down shutters of any description exc 1.00 sqm & nexc 2 sqm each complete all as specified and directed.

S&F mild steel framed work just as doors, ventilators, and as in hold fast, ladders, railings, Framed Guard bar, door chowkat etc with ends of bars shouldered and/or riveted complete welded hinged and similar work Conforming to Fe-290 Gde-E-165 including PCC 1:2:4 filling for hold fast and back filling in chowkat etc complete all as specified and directed by Engr-In-Charge.

Material & labour for box type steel window 1.25 mm thick made of ERW tube P-Section of size 60 x 25 mm double rebated outer frame comprise of glazed skeleton shutter(two gauged shutters and two glazed shutter) of ERW tube P-Section size 50 x 20 mm and 1mm thick one/two Nos openable leaf consisting of two Nos sash bar of T-Section 20x3mm welded to frame with one No Vertical mullion of ERW box type T-Section of size 60 x 25 mm and 1.25 mm thick and FI 2 mm thick welded / screwed to frame for fixing of glass including fittings and fixture like Handle, Tower Bolt, stopper, cleat, pintal hinges, hold fast etc. (a) Hold Fast, 150mm long of 120mm x 3 mm made to shape -04 Nos per window. (b) Handle of Z sec 20mm x 25mm, 100 mm long -1 No per leaf (c) MS Tower bolt 150mm long - 2 No per leaf (d) Z Sec 20mm x 25 mm, 100 mm long stopper - 1 No per leaf (e) Cleat 55 mm long of hollow square 15mm x 20mm x.63mm welded to hinge -1 No per leaf. (f) MS Pintal hinges of size 75mm x 12mm - 2 Nos per leaf (g) 12 mm square guard bar, 10 cm centre to centre.

(h) 25x4 mm flat iron all around for joint of both frame. (j) One coat of red oxide primer to MS window and guard bar Note: Including taking down old steel window and making good dismantled portion with PCC 1:2:4 type B0 including hold fast PCC (four No’s for Each window) & around required plaster in CM 1:4 and match with existing finishing complete all as specified and directed by Engineer-in-charge.

Material and Labour for Box type steel ventilator made of ERW tube P-section of size 60mmx25mm outer frame ( single rebated), comprises glazed shutter, frame of ERW tube and FI 2mm thick welded/screwed to frame for fixing of sheet glass including fixture and fittings like as Stopper, Cleat, Pintal hinges, holdfast etc all as shown on drg No CEJZ/TD1019/08 sheet 1/3 to 3/3 dt 01 May 2008 complete all as specified. (a)12mm Sq Guard bar 10Cm C/C (b)One coat of red oxide primer to MS window and guard bar Note: Including taking down old steel window and making good dismantled portion with PCC 1:2:4 type B0 including hold fast PCC (four No’s for Each ventilator) & around required plaster in CM 1:4 and match with existing finishing complete all as specified and directed by Engineer-in-charge.

Material and Labour factory made glazed skeleton shutter for door 35mm thick 2nd class hard wood(Hollock) open rebated prepapred to receive glass, guage etc ( without sash bars) edges of framing plain, chamfered or rounded,fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part-I Section 8 Clause 8.24(a) complete all as specified and directed.

S&F for 35mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Supplying and fixing factory made Solid PVC Moulded Door shutter with wood free EPS, 28-30mm thick (stiles), with 2 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm Plain colour PVC sheet on back face, supplying & fixing at site as per specification & drawing complete all as specified and directed by Engr-In-Charge.

S&F floor door stopper of aluminium alloy body and tongued, anodised, with hard drawn steel spring, fixed 140mm minimum length complete all as specified and directed.

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples with proper fixing of beading, nailing with edges complete all as specified and directed by Engr-in-Charge.

Description all as per Srl item no 11.00 above but fixed in repair for old steel window.

S & F 150mm aluminum handles, cast type, anodised etc complete all as specified.

S & F 200 mm aluminum anodised barrel tower bolts of extruded sections and fixed complete.

S & F 150 mm aluminum anodised barrel tower bolts of extruded sections and fixed complete.

S & F butt hinges 100 mm size medium weight cold rolled mild steel(zinc chromate coating)complete all as specified and directed.

S&F 250mm sliding door bolts aluminium alloy anodised, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified.

S & F 300mm ordinary rat Tail rod pattern springs, including roller and roller plate complete all as specified

Supplying and fixing 3mm thick ordinary sheet glass and glazing with oil putty or fixed in squares not exc 0.50 Sqm in each panes complete all as specified.

S&F 3mm sheet glass ordinary quality and glazing with oil putting in squares over steel window n.exc 0.50 Sqm each including hacking of old glass panes complete all as specified and directed.

Supply and fixing 3mm thick figured glass pin head type and glazing with oil putty in squares not exc 0.50sqm in each pane complete all as specified and dircted.

M & L for two coats of synthetic enamel paint over one coat of primer (Pink Primer) on new wooden surfaces exceeding 10cm width or girth including preparation of surface complete.

M&L for two coats of synthetic enamel paint on new steel surface exc 10 cm width or girth over one coat of primer (Red oxide/ Zinc chrome) incl preparation of new surfaces complete.

Description all as per Srl item no 23.00 above but except red oxide Zinc chrome primer over steel windows/ventilator complete all as specified and directed by Engr-In-charge.

M&L for one coat of synthetic enamel paint over old steel surface including preparation of old steel surface exc 10 cm width or girth complete all as specified and directed.

Supply and fixing in repair PVC coated curtain rods 25mm dia including, brackets to hold the rod & a set of ABS finials, wall to wall, brackets fixed to wall complete set ( as per sample kept in GE's office) of approved quality complete all as specified .

S&F in repair 20 mm bore dia gate valve,gun metal with iron wheel head,screwed both ends and fixed all as specified and directed.

Supplying and fixing in repairs PVC valve less syphonic action type low level flushing cistern of 10 ltrs capacity with inlet ball valve, float valve, handle type including 32mm dia of PVC (Heavy duty) flush pipe including brackets complete all as specified and directed by Engr-In-charge.

Supply and fxing in replacement of rotational moulded polythene water storage tank, white coloured, tripple layer cylindrical vertical with closed top 500 litre capacity hoisted and fixed in position, including inlet and outlet pipe connections, 20mm dia and 15 mm dia GI pipes medium grade respectively, 20mm GI pipe medium grade over flow pipe 15 cm long wash out with plug and brass ball valve 20mm, high pressure with polyethelyne float and fly nuts complete all as specified and directed.

S&F in repair sheet glass corner shelf assembly consisting of 5.5mm thick sheet glass corner shelf with chromium plated bracket guard and railing complete all as specified and directed.

S&F in repair glossy finish towel rail, 20mm dia, D-type 50 cm long between flanges all as specified and directed.

Demolition of brick work built in cement mortar complete all as specified and directed.

M&L for brick work using sub class ‘B’old size bricks, straight or curved on plan exc. 6 mean radius in CM 1:6 complete all as specified and directed.

Description all as per Srl item No 33.00 above but except brick.

M&L for brick work using sub class ‘B’ old size bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

S & F in repair for vitreous china squating pan of (Orissa Pattern) size 580 x 440 mm white with 'P' or 'S' trap front or back inlet and integral foot rest (excluding flushing cistern and flush pipe) fixed incl cement concrete bedding as required set complete all as specified and directed.

Supply and fixing in repair vitreous china wash hand basin(white) wall hung corner type of size 400 x 400 mm including bracket, CP waste coupling 32mm, waste pipe, chain, plug and porcelein stopper complete all as specified.

S & F sink in repair made of stainless steel 1mm thick with plug washer and waste coupling, waste pipe including fixing cantilever brackets and connecting union to pipe over all size 915mm x 460mm bowel size 410mm x 330mm x 160mm, complete all as specified and directed.

S&F in repair stainless steel plate Rack of size 750x750x250mm weight not less than 7.5 kg with folded edge gloss finish complete all as specified and directed.

S&F in repair 15mm bore G.I tube medium grade freed to wall or under floor complete including cutting chases and make good in CM 1:3 complete.

Description all as per Srl item No 41.00 above but 20mm bore

M&L for PVC connection 45cm long superior quality with PTMT nut on both side .

Supply and fixing bib tap long body fancy type 15mm dia chromium plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule including taking down old PVC tap complete all as specified and directed by Engr-In-Charge.

S&F in repair 15mm bore stop cock concealed as in repair long shank chromium plated fancy type screwed down high pressure with crutch or butter fly handle.

S&F Angle cock CP fancy type 15 mm bore screwed down high pressure with crutch or butterfly handle & screw both end for iron pipe or for Unions complete including taking down old PVC angle cock complete all as specified and directed.

S & F Pillar cock SWAN NECK, fancy type cast copper alongwith capstan heads, chromium plated, screwed down high pressure , with or without lettered ‘H’ or ‘C’ with long screwed shanks and fly nuts, screwed for iron pipe size 15mm including taking down old PVC pillar tap complete all as specified and directed by Engr-in-charge.

Supply and fixing 125mm dia, Brass chromium plated, shower rose with swivel joint fixed to GI pipe, complete including taking down old PVC shpwer rose all as specified and directed by Engr-In-charge.

Taking down cement plaster from wall / ceiling including raking out joints hacking for key scrubbing down with water complete.

M&L for 15mm rendering in cement mortar (1:6) on brick/concrete surfaces finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm rendering in cement mortar (1:4) on brick/concrete surfaces finished the surface even and smooth without using extra cement complete all as specified and directed.

M& L for 10mm rendering in cm (1:3) on ceiling surfaces finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

Material and Labour for preparation of new plastered surfaces and applying two coats of cement base paint on wall complete all as specified.

Material and Labour for preparation of new plastered surfaces and applying two coats of oil bound distemper over coat of primer of chalk whitening on walls complete over 1mm thick wall care putty complete all as specified and directed by Engr-In-Charge.

Material and Labour for removal of existing treatment by wire brushing and washing, rubbing down and stopping of surfaces and applying two coats of oil bound distemper over applying 1mm thick wall care putty on walls complete all as specified and directed by Engr-In-charge.

M&L for preparation of new plastered surfaces and applying three coats of white wash on ceiling surface complete all as specified and directed.

Material and Labour for prepration of existing treatment by wire brushing and washing, rubbing down and stopping of surfaces and applying one coat of cement base paint complete all as specified.

Material and Labour for preparation of old decorated plastered surfaces and applying one coats of white wash on ceiling complete all as specified.

M & L for coloured (non skid) ceramic tile of size 400x400x6-7mm thick over and incl 15mm thick cement screed in CM(1:6) set and jointed in neat cement slurry and pointed with white cement (over floor, skirting, almirah and shelves etc) mixed with pigment to match the colour of tiles including dismantling of existing old tiles complete all as specified.

S&F Coloured/printed non skid ceramic tiles 6-7mm thick (Square/rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match over 15 mm thick screed bed or bedding layers in CM 1:6 including dismantling of old tiles complete all as specified and directed.

M & L for ceramic glazed coloured printed tiles (some portion highlighted with contrast colour) of size 300 x450 x 6-7 mm thick on and incl 10mm thick Rendering in cm (1:4) set and jointed in neat cement slurry and pointed in coloured cement mixed with pigment to match the colour of tiles on vertical surfaces of well as in skirting / dado including dismantling of old tiles complete.

M&L 18 to 20mm thick for machine cut green marble over riser, steps of stairs and skirting stone grinded & polished top of stone to achieve granite mirror finish including rounding edges and nosing including dismantling of old broken stone complete all as specified.

M&L 16 to 18 mm thick granite slab as in cooking platform and shelves machine cut flooring, skirting, riser, tread, cill, jamb etc incl 15mm thick cement mortar 1:6 set and jointed in neat cement slurry and pointed with coloured cement mixed with pigment to match the shade of slab incl cutting rubbing and polishing incl nosing to the edge of granite stone slab including dismantling of old stone complete all as specified and directed by Engr-in-Charge.

M&L for Precast RCC (1:2:4) type B-1 using 20mm graded stone aggregate set in cement mortar 1:6 as in landings, cover slabs for manhole etc, water tank base and similar work complete all as specified and directed including demolition of existing RCC.

M&L for RCC (1:2:4) type B-0 using 12.5mm graded aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, deck slabs, balconies and in shelves including chasing, cutting and hooking/welding to existing RCC and like including demolition of existing reinforced RCC .

M&L For RCC (1:2:4) type B-1 using 12.5mm graded aggregate as in stairways parapet coping, including steps, staircase railing/coping, benching for roof etc and work of similar type including any formwork required in sides/riser etc complete all as specified and directed.

M&L for form work to soffits of suspended slab such as roof slab, Floor slab, shelves and chajjas etc and making surface fair finished complete all as specified and directed by Engr-In-Charge.

Mild steel TMT bars 8 to 10 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for demolition of RCC as in shelves of kitchen and almirah etc, vertical balcony walls and similar work including cutting reinforcement as required complete all as specified and directed.

M&L for mild steel work as in railing tubular section or other section for railings and similar work etc complete all as specified and directed by Engr-In-charge.

Demolition of PCC as in ground floor & Paving n.exc 15cm (Below or above) ground level including disposal of rubbish to a distance n.exc 500mtr where directed.

Dismantling of brick tiles single layer on roof, jointed and grouted/pointed in cement mortar including cleaning serviceable tiles and stacking properly for reuse, disposal of unserviceable tiles and debries/rubbles from site complete all as specified and directed

M &L for 40 mm thick brick tiles laid on cement mortar 1:6, 15mm thick and jointed grouted, flush pointed in cement mortar (1:3) complete all as specified and directed.

Description all as per Srl item No 73.00 above but except tiles.

M&L for uprooting grass on old existing mud phuska over roof surface, removing rubbish off the premises, cleaning surface complete all as specified and directed by Engr-In-Charge.

Demolition of mud in roofs, any thickness including plastering and leaping complete all as specified and directed by Engr-In-Charge.

Laying and spreading of mud phuska over roof surface obtained from item No-78 above including compaction and to the entire satisfaction of Engr-In-charge.

Removal of mud phuska away at a distance of 250 mtr complete all as specified and directed by Engr-In-Charge.

M & L for PCC (1:2:4) type B-1 (20 mm graded stone aggregates) as in padding over roof slab ,mud stops and sunken portion bed for slope etc and similar works complete all as specified and directed by Engr-In-Charge.

M&L for cement concrete type F2 1:7:12 (40mm graded aggregates) as in sunken floor all as specified and directed including demolition of PCC and removal away from residential area.

M& L for 10mm rendering in cm (1:3) as in sunken portion, roof surfaces including WPC @3% by weight of cement, finished the surfaces even and smooth without using extra cement complete all as specified and directed. Note: WPC should be paid under sepearate item.

Supply only Intergral Water Proofing compound complete all as specified and directed.

S & F in repairs 40mm dia GI pipe medium grade as in spout of sunken floor, roof surface all as spesified and directed

M&L for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm for roof surface,providing overlap for sides including cleaning surfaces etc complete all as specified and directed.

M & L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) laid on roof (including chase cutting on sides of parapet wall roof for membrane and making good with CM 1:3 as per SSR Part-I), sunken portion laid on bitumen surfaces by forced torching application complete all as specified and directed by Engr-In-Charge.

M&L for PCC 1:3:6 type C-2 using 20mm graded stone aggregate as in 50mm thick plinth protection and as in path including demolition of PCC complete all as specified and directed.

S & F in repair machine pressed factory made precast coloured chequered cement concrete tile 30 cm x 30 cm x 25 mm thk set, jointed & pointed in neat cement slurry with grey cement and pigment in floor including screed bed 20mm thick in CM 1:6 bedded and jointed complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-2 20mm graded aggregate as in sub base of flooring complete all as specified and directed.

Dismantling cast iron pipe 75/100mm bore fixed to wall/laid in trenches etc including any type of joints, T, Y, bend etc complete all as specified and directed by Engr-in-Charge.

Supply and fixing for PVC (SWR) floor trap 110 mm dia of outlet, with CP grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1, complete including dismantling of CI floor trap all as specified and directed by Engr-In-Charge

Supply and fixing 110 mm bore PVC (SWR) pipes rain water pipe single socketed in any length joints fixed to walls with and including clamps (Minimum 03 Nos each span any length), nut bolts etc complete all as specified including demolition of existing PVC rainwater pipe complete all as specified and directed by Engr-in-Charge.

Supply and fixing 110 mm bore PVC (SWR) pipes for sullage, toilet and bath single socketed in any length joints fixed to walls with and including clamps, nut bolts etc complete all as specified and directed by Engr-in-Charge.

Supply and fixing 75 mm bore PVC (SWR) pipes waste pipe single socketed in any length jointslaid in floor, trenches etc set in cement mortar complete all as specified.and directed by Engr-In-charge.

S&F PVC(SWR) Junction 'T', 'Y' etc and similar pieces of 110mm equal or unequal with access door to be fitted with PVC pipe complete all as specified and directed by Engr-in-Charge.

Supply and fixing PVC (SWR) bends with access doors 110mm bore ( in any radius) diminishing peices or tapers (larger bore measured) ,complete all as specified and directed.

Supply and fixing PVC (SWR) bends without access doors 110mm bore ( in any radius) diminishing peices or tapers (larger bore measured) ,complete all as specified and directed.

Supply and fixing PVC (SWR) reducers 110/75mm dia with access doors, complete all as specified and directed.

S&F in repair PVC(SWR) vent cowl 110 mm bore complete all as specified and directed by Engr-In-Charge.

M&L for repair to RCC Chajjas, roof projection edges ,hanging part of chajjas, edges of chajjas, RCC parapets, under the roof / floor slabs with PCC 1:2:4 (using 12.5mm crushed graded agg) incl necessary renforcement 6mm to 08mm TMT bars , form work , MS wire mesh for bounding the concrete on ground required and plaster work in CM 1:3 at any height of buildings making edges fair and even and smooth etc completed all as specified and directed by Engr-in-Charge.

S&F for 4mm thick acrylic sheet board of High quality with Media printing of 3m of best quality (size/frame of board, design of bd, type of print on sheet, size of studd, samples of letter, pictures, writing will be provided by accepting officer or Engr-in-Charge) and fixed at any height from GL to 29 Mtr height incl stainless steel studds (min 4 studs at each board / sheet ) complete all as specified and directed incl dismantling of existing damaged sheets. Note : Minimum weight of Acrylic Sheet not less than 4.70kg per sqm (Acrylic sheet make A Cast / Astari / Marka Cipta and stainless steel of grade A-ISI 304(1818).

Supply and fixing Godrej type in pattern cupboard shutter of 0.8mm thick MS sheet fixed in & including angle iron frame 35x35x5mm including necessary fittings such as CP handle, lugs, hinges, locking arrangement including two coats of synthetic enamalled spray paints over a coat primer complete all as specified.(colour as per choice of Engr-In-Charge)

Supplying and fixing 18mm thick solid PVC board as in cup board shelves in kitchen, shutters etc complete all as specified and directed .

Description as per Srl Item No. 102.00 above but board with one side prelam of thickness 20-22mm as in cabinet shutters including piano hinges in length per shutter fixed to board with screw , Stainless steel handle 100 mm long 01 no per shutter ,01 catcher for each shutter complete all as specified and directed .

S&F 1.00 mm thick mild steel black sheet in steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified.

M&L for 18-20mm thick prelaminated plywood of grade BWP, both sides balancing white lamination, fixed in partitions of almirah shelves vertical and horizontal to match design including stainless steel brackets/cleat to support with wall and plywood including demolition of decayed plywood complete all as specified and directed by Engr-in-charge.

M&L for 18/19mm thick prelaminated particle board , interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed in reps with screws, built in cup board, almirah shelf etc including external teak wood leaping 6mm thick in length, including piano hinges bright finish electrogalvanised 35mm per leaf through length completely fixed to chowkat, 01 no catcher per leaf, 01 no 75mm handle per leaf complete all as specified and directed.

M&L for vitrified ceramic tiles 8-10mm thick (Dark shade as decided and approved by GE) laid over 20mm thick cement screed in CM(1:6) set and jointed in neat cement slurry and pointed with white cement(over floor) mixed with pigment to match the colour of tiles.area of each tiles not exceeding 0.36 sqm, in floors etc, complete including dismantling of existing floor all as specified and directed by Engr-In-Charge and sample, shade, colour approved by GE will be final and inclusive of rates.

M&L for vitrified ceramic tiles 8-10mm thick (Dark shade) polished, over and incl 10mm thick cement screed in CM(1:4) set and jointed in neat cement slurry and pointed with white cement as in skirting mixed with pigment to match the colour of tiles.area of each tiles not exceeding 0.36 sqm, in floors etc, complete including dismantling of existing floor, wall tile all as specified and directed by Engr-In-Charge and sample, shade, colour approved by GE will be final and inclusive of rates.

S&F Powder coated anodised aluminium sliding window with frame, three track (two shutter of glass and one shutter of wire mesh) window shutter, sliding shutter frame size as per Jindal sliding window three track specifications including supplying and fixing of tinted/frosted glass 5.5mm thick for sliding shutter for two shutter each window and stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm, aluminum glazing clips fixed with rubber gasket, locking arrangement for shutters complete mesured as whole complete all as directed by Engr-in-Charge.

S&F powder coated anodised aluminium three track frame section top,bottom and sides including all fittings to wall and making good complete all as specified and directed by Engr-in-charge.

S&F anodised aluminium powder coated (min thickness of powder coating 50 micron) ventilator,fixed type with plain glass of thickness 5.5mm, aluminium section weighing minimum 0.55kg/m including necessary joining cleats, glazing clips, rubber packing for 5.5mm thick glass, anodised aluminium snap beading screws etc measured as whole with frame. Complete all as specified and directed by Engr-In-charge.

S&F powder coated (min thickness of powder coating 50 micron) anodised aluminium door shutters, aluminium section weighing minimum 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, 03 nos hinges each door, anodised aluminium snap beading screws, tinted glass 5.5 mm thick completely fitted with rubber packing etc including all fittings and provision for mortice lock arrangement. Complete all as specified and directed by Engr-in-charge.

S&F powder coated aluminium frame for door frame with one or more rebates including joining cleat for fixing etc, Complete all as specified.

S&F aluminium extruded section body door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000mm in width complete all as specified and directed by Engr-In-charge.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet aluminium (extruded section body) foundation box, main body with stainless steel cover,governing pivot made of brass, other parts made of mild steel heavy duty and fixed.

M&L for applying two coats of 100% premium exterior Acrylic emulsion weather coat paint over new plastered surface in camouflaging pattern to walls, slanting walls, under base any shape and area over one coat of priming surface including preparation of new surface complete all as specified upto height n.exc 6 mtr from GL and directed by Engr-in-charge.

M&L for applying one coat of 100% Premium exterior Acrylic emulsion weather coat paint in camouflaging pattern over old plastered surface including prepration of old existing treatment by wire brushing with sand paper to wallsany shape and area complete all as specified and directed by Engr-in-charge.

S&F aluminium wire guard mesh of 4mm nominal dia of wire and average width of aperture 75-85mm and fixed with aluminium frame / staples complete all as specified and directed.

M&L for Aluminium mortice lock 4-lever 100mm size fixed to aluminium door shutters complete all as specified and directed by Engr-In-Charge.

Taking down aluminium/copper point wiring from existing conduit / batten (light, fan, socket or power) complete such as switches, ceiling rose, pendent, regulators, socket, light fittings etc and removing material from site and making good the disturbed surface of wall / floor etc, complete all as specified and directed

M&L for point wiring with 1.5 sqmm (Nominal area ) 1100 Volt PVC Insulated , FRLS unsheathed and multi stranded copper conductor cable in old PVC Concealed conduit for one light / fan point or bell point controlled by one switch (including cutting chases and making good the distributed surfaces) and fixing new 3mm thick plastic laminated sheet top cover, sheet screws and 1.6mm thick GI sunken boxes after removing old unserviceable plastic laminated sheeet and sunken boxes included 1.5 Sqmm stranded copper conductor with green PVC Insulation earth contunity conductor connected to common earth dolly etc . complete all as specified and directed Note : The cost of sunken boxes and bakellite sheet is included in the quoted rate)

Description all as per Srl item No 121.00 above but for one 5 amps socket outlet independent complete all as specified.

Description all as per Srl item No 121.00 above but on the same board complete all as specified

Description all as per Srl item No 121.00 here-in-before but with 2.5 Sq mm size cable multi stranded FRLS copper wire unsheathed for one 3 pin socket outlet 15 Amps on independent board including continuous earth wire of PVC insulated 1.5 Sq mm copper solid conductor connecting to common earth dolly complete.

Supply and fixing of switch piano type 6 Amp one way 230 volts AC complete all as specified and as directed.

Supply and Fixing of socket outlet 5 pin, 6 Amp flush type 230 volts AC complete all as specified and as directed

Supply and Fixing of switch piano 16 Amp type one way 230 volts AC complete all as specified and as directed

Supply and Fixing of socket outlet 6 pin 6/16 Amps multi purpose flush type 230 volts AC complete all as specified and as directed

Supply and Fixing of switch type regulator 5 step 230 volts AC complete all as specified and as directed

Supply and fixing of ceiling rose 65/50 mm two to three terminals complete all as specified.

Supply and fix of MCB 40 Amps single pole, AC 230 Volts complete all As specified and directed.

Supply and fix of MCB 40 Amps single pole with neutral, AC 230 Volts complete all As specified and directed.

Supply and fix of MCBs single pole (SP) 5 to 32 Amps with 10 KA breaking capacity of 'C' series in distribution boards complete all as specified and directed.

Supply and fixing in replacement Sheet metal enclosure for DB's when MCB's to be used single door factory made flush fixed complete with 200 Amps rated busbar 240 Volts single phase 8 ways complete all as specified

Supply and fix in replacement for sub main wiring with two run of single core (FRLS) PVC insulated and unsheathed cable with copper conductor (Multi strand) having nominal area 6.0 Sqmm drawing into and including PVC non metallic rigid conduit medium grade of adequate size and making electric connections including one run (FRLS) PVC insulated single core copper conductor cable 6.0 Sqmm as a earth continuity conductor(green colour) and including non metallic medium grade rigid PVC conduit, including cutting chases in brick wall, and making good to match the existing specifications complete all as specified and directed by Engineer-in-Charge. Note :- (i) Rates are deemed to be included cutting and making holes in wall/floor for passing in or through conduit (ii) Two run of 6.00 sqmm single core (FRLS) PVC insulated copper conductor cable, one run of 6.0 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of suitable size will be measured as a one unit.

Description all as per item No 135.00 above but for 4.0 sqmm

Material and labour of lamp holder insulated body with 9 Watt LED Bulb, back plate batten/angle type for batten fitting fixed on bakelite sheet 100mmx100mm 230V AC cool day light 6500K having maximum height 1020 mm heavy duty complete all as specified.

S & F in repairs, installation, commissioning and testing Polycarbonate ASTA CPRI approved OEM made Meter Panel. The Panel shall be made of modular POLYCARBONATE THERMOPLASTIC ENCLOSURES which should be UV resistance in accordance with IEC 61439-1, clause 10.2.4: Meter Panel (Mini. Size 600 x 600 x 170 ) Wall Mounted type on Mounting Structure RAL 7016. The Meter Panel should be anti-acid, anti corrosive & Fully Transparent Door for meter Vision. Degree of protection against mechanical load should be IK08 (5 Joule) in accordance with IEC 62262. The manufacturer of panel shall submit a copy of his CPRI TEST REPORTS with Short Circuit Test IN POLYCARBONATE only also share panel assemble by OEM, channel partner or sister concerned assembly will not accepted. DEGREE OF INGRESS PROTECTION IP 65 IN ACCORDANCE WITH IEC 60529. The gasket should be internally embedded made of polyurethane. The manufacturer of panel SHALL submit a copy of TYPE TEST REPORT of a board made out of Polycarbonate thermoplastic panel in accordance with IEC 60439-1.

The CPRI report shall have mention of following tests performed and passed out satisfactorily Temperature Rise, Dielectric Properties, Short circuit withstand current – Rated peak, short time withstand current and Rated Conditional Short Circuit Current, Effectiveness of Protective Circuits and submit the copy of type test reports for Polycarbonate Thermoplastic Board only. Test Reports submitted of other material of construction like MS, SS will not be applicable. Each Board shall have individual routine test report of the manufacturer. The panel should passed glow wire test 960oC in accordance with 60695-2-11 [flame retardant and self-extinguishing. One Main Incomer MCCB 100A TP 25KA Thermal /Magnetic Release with spreader link. MCCB/MCB Knob Operated by Flip Cover. Indicator Provided on each phase. Provision of Four Nos Single Phase Sub-Meters in Panel. Provided Output supply by MCB DP 40Amp 4 Nos. Meter Enclosures & Enclosures Accessories as per RAL 7035. Ten Nos Terminal Blocks Provided for output Supply. NOTE:- Rates of main incomer MCCB 100 AMP and MCB DP 40 AMP 4 Nos is included in quoted rate and no extra paymentwill be made for it.

Supply and fix exhaust fan, steel body single phase 230V of size 300 mm sweep with blades, frame and louvers all as specified and directed.

Supply and fixing of LED T-8 tube light fitting with sinle side connection LED tube rod 18/20 W, 4 Feet made of CRCA sheet steel box type including bipin holder and connection with PVC insulated twin core 23/0.0076 ywisted copper cable from ceiling rode to light fitting complete all as specified and directed.

Supply & fix LED Street Light Luminaire 25 watt 6000K with high power LED cool white, CRI 75, +/- 5% supply voltage 220/240/50 Hz, light engine driver base. pole adapter, powder coated pressure die cast aluminium with heat resistant toughened glass with lens all as specified and as directed.

Supply and fixing of security light mounting bracket made out of GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 Nos of pole fitting clamps made out of MS flat of size 40 x 6 mm and nuts and bolts and painting with aluminium paint, all as direced by Engr in Charge

Supply, laying in trenches or wall and testing in replacement of cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (Heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sqmm 4 core all as specified and as directed.

M&L for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by GI pipe 15 mm bore( light grade) and watering pipe 20 mm bore GI pipe (light grade ) and chamber of pcc 1:4:8 type D2 using 40 mm graded stone aggregate and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg. 50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone agg. reinforced with 8 mm dia MS tor bar @ 80 mm c/c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 3 of SSR PART 1 , with charcoal dust and salt complete and earth lead connected to earthing test point (up to main switche, DBs) complete all as specified & testing on completion.

Excavation in trenches not exceeding 1.5m wide & not exceeding 1.5m in depth and getting out in any type of soil all as specified and as directed.

Returning, filling including spreading, leveling, watering and well ramming in layers not exc 25 cm thick all as specified and directed.

Removal of surplus excavated soil to a distance not exc 50m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified.

Supply, laying & fixing in replacement double wall corrugated (DWC) pipes made of high density polythyline (HDPE) with all accessories i.e. all type of joints, Sockets, Elbows, bends and End caps etc.. all as specified and directed by Engr in Charge of size 63mm outer dia and 50 mm inner dia.

Supply and lay on wall/ floor etc GI pipe light grade of dia 32 mm for protection of cable all as specified and directed.

Taking down ceiling fan/geyser/exhaust fan in situ and refixing after servicing, repairing and painting them, scratching old paint and preparation of surface for painting with one coat of white / grey enmeled paint and including cable from ceiling rose to fan complete all as specified and as directed.

Taking down old meter and refixing them in new meter panel and make necessary connection to bus bar and MCB DPs in meter panel all as specified and as directed.

S & F of decorative wall light fixture made up of polycarbonate , suitable for and including 9 W retrofit LED lamp B22 base all as specified and as directed.

S & F in replacement of single pole and neutral sheet metal enclosures with two pin & earth plug and socket complete with one singlr pole MCB of 20 amps complete all as specified and as directed.

Supply and fixing in replacement of bell push 6 amps one way 230 volts AC complete all as specified and as directed.

Supply and fixing in replacement of bell ding dong AC 230 volts complete all as specified and as directed.

Supply and fix exhaust fan, steel body single phase 230V of size 220 mm sweep with blades, frame and louvers all as specified and directed.

Supply and fixing in replacement pvc connection of size 600 mm length 15 mm dia all as specified and as directed

S & F in replacement of LED bulkhead light fittings 10 watt white including LED strip as per IP 65 in engineering plastic housing with clear primatic diffuser and making necessary connection complete all as specified.

M&L for road cutting including excavation and getting out, returing fittling in spreading levelling and well ramming in layers, soling with broker builders or quarried stone, inter stices filled, 7.5 cm thick (compacted thickness) WBM (water bound macadam) with coarse aggregate retreived from road cutting consolidated to required gradient and camber, including Applying evenly a priming /tack coat with bituminous primer and making surface even and getting our surplus soil complete all as specified and directed.

Supply and fixing Bus bar chamber made out of from CRCA sheet 2 mm thick including making concealed in the wall with nuts and bolts and color wash to match with exsting, powder coated of size 600 x450 x 150 mm in IP-65 consisting of the following :- (a) Incoming MCCB 160 Amp 4 pole 16 KA, (b) Outgoing Alluminium Bus bar duly insualted RBY and Black- 01 Set (c) Led indicator RYB = 01 Set

tarlok singh contractor

Jaspal Construction Co.

M/s MAHAJAN CONSTRUCTION CO.