PROVISION OF GUARD ROOM WITH ATTACH TOILET FACILITY ,CYCLE STAND AT BHALUKUMARA AND PROVISION OF GUARD ROOM AT SARAIBARI AND SPECIAL REPAIR TO BLDG NO-215 OTM ACCN AT LICHUBARI IN JORHAT MILITARY STATION UNDER GE JORHAT

Amount

Dismantling of Asbestos cement (corrugated, semi corrugated etc) sheets in roof covering complete all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as directed.

Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) complete all as directed.

Dismantling timber scantling in unframed work, 40 Sq cm and over in section, in any position, complete all as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as directed.

Taking down cement plaster from brick or concrete surfaces of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) n. exc. 1.5 Sq. M each, complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sq. M but not exc. 4.0 Sq M each, complete all as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as directed.

Taking up or down, steel tubing 15 mm bore, and connection including cleaning for re-fixing or removal from site of work complete all as directed.

Taking up or down, steel tubing 20 mm bore, and connection including cleaning for re-fixing or removal from site of work complete all as directed.

M & L Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out soft loose soil complete all as specfied and directed

Excavation in post holes (or similar holes) each not exc. 0.5 Cum and getting out in soft/ loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc. 25 cm, watering, and removing surplus soil to a distance not exceeding 50 m complete all as specified and as directed

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil ,complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and exc 1.5 m but n exc 3 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n exc 10 sq m on plan and exc 1.5 m but n exc 3 m in depth and getting out in soft/loose soil , complete all as specified and directed.

Excavation over area n.exc 1.50 M deep for foundations and getting out in soft/loose soil complete all as specified and directed.

Excavating over area each additional 1.5 mtr in depths beyond the first 1.5 mtr and getting out in soft/loose soil complete all as specified and directed.

Returning filling in soft/loose soil, including, spreading levelling watering and well ramming in layers not exc. 25 cm complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 Metres and depositing where directed at a level n. exc. 1.5 M above the starting point complete all asspecified and directed.

Earh filling , in floor etc ,spreading in layers n exc. 25 cm thick;watering, ramming/rolling and finishing to required size, shape,etc., n exc. 1.5 m high from base,complete all as specified and directed. NOTES:- (i) Earth(Soil) incoporated in work shall be out side of defence land (ii) Sample of Earth to be used in shall be approved from Engineer in Charge in writing by the Contractor before using the earth required under this item.

Materials and Labour for plain cement concrete (1:2:4) Type B-2 using 40 mm graded aggregate in foundations, filling and mass concrete complete all as specified and directed.

Materials and Labour for plain cement concrete (1:4:8) Type D-2 using 40 mm graded aggregate in foundations, filling and mass concrete complete all as specified and directed.

Materials and Labour for plain cement concrete (1:3:6) Type C-2 using 40 mm graded aggregate in foundations, filling and mass concrete complete all as specified and directed.

Materials and Labour for reinforced cement concrete M-25 design mix in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete ,complete all as specified and directed.

Materials and Labour for reinforced cement concrete M-25 design mix in columns; pillars; piers; posts; struts etc,complete all as specified and directed.

Materials and Labour for reinforced cement concrete M-25 design mix in roof beam beam,GB,Lintel beam etc,complete all as specified and directed.

Materials and Labour for reinforced cement concrete M-25 design mix in chajjas,complete all as specified and directed.

M&L for RCC M-25 in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves , baffle wall and the like slabs etc. complete all as specified & as directed.

M&L for PCC (1:2:4) type B-I with using 20 mm graded aggregate as in benching, kerbs copings, edging of drain etc including necessary form work wherever required all complete as specified and as directed.

M&L Precast cement concrete 1:11/2:3, type A1 (Using 20 mm graded granite stone aggregate) in landings, slabs cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:4 complete all as specified and directed

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings , girders, bressummers, lintels, cantilevers, shelves including supports,overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete, flat, complete all as specified and directed.

Use and waste of form work to chullah hoods, chajjas,troughs and similar items including edges for fair finished surfaces of concrete, flat, complete all as specified and directed.

Use and waste of form work to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surfaces of concrete, square, rectangular or polygonal, complete all as specified and directed.

Use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sided and soffits of plinth beams and similar works; vertical or to batter for rough finished surfaces of concrete, flat, complete all as specified and directed.

M&L for use and waste of form work to soffits of suspended slabs such as roof slabs, landings floor slabs and similar work not exceeding 200 mm thick (horizontal or sloping) for fair finished surfaces of concrete complete all as specified and directed.

Materials and Labour for 75 mm thick plain cement concrete (1:2:4) type B2 using 40 mm graded aggregate as in sub base in floor/paving/hardstanding , complete all as specified and directed.

Materials and Labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded aggregate as in sub base in floor/paving/hardstanding , complete all as specified and directed.

M&L for rendering 20 mm thick cement plaster in CM 1:4 in two layers of 10mm each using WPC in finishing layer on fair faces of brick or concrete surface finished the surface even and fair complete all as specified and as directed.(Note : WPC for finishing layers will be measured and paid separately as supply only)

Materials and Labour for 75 mm thick plain cement concrete (1:4:8) type D2 using 40 mm graded aggregate as in sub base in floor/paving/hardstanding , complete all as specified and directed.

Materials and Labour for sand filling under floors or in foundations including watering and consolidation, complete all as specified and directed.

Materials and Labour for polythene film, black, 50 micron, laid in floors, complete all as specified and directed.

M&L for cement concrete 25mm thick type B-0, 1:2:4 (12.50 mm graded aggregate) as in base of flooring, finished even and rough to receive the top layers all complete as specified and as directed

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm,conforming to IS 15622, Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:4),complete all as specified and directed.

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,conforming to IS 15622, Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:4),complete all as specified and directed.

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,conforming to IS 15622, Grade B II, on vertical surfaces of wall such as dados, skirting etc., set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 10 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed.MAKE:- (Johnson/Kajaria or equivalent make )

Materials and Labour for, Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,conforming to IS 15622, Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:4),complete all as specified and directed.

Materials and Labour for, Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,conforming to IS 15622, Grade B II, on vertical surfaces of wall such as dados, skirting etc., set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 10 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed.MAKE:- (Johnson/Kajaria or equivalent make )

Material and Labour for Digital Vitrified Ceramic Tiles, , 10 mm thick (square/rectangular) polished area of each tile not exceeding 0.36 Sq M, on floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6), complete all as specified and directed.MAKE:- (Johnson/Kajaria or equivalent make )

Material and Labour for Digital Vitrified Ceramic Tiles,, 10 mm thick (square/rectangular) polished area of each tile not exceeding 0.36 Sq M, on vertical surfaces of wall such as dados, skirting etc., set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 10 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed.MAKE:- (Johnson/Kajaria or equivalent make )

Materials and Labour for, Digital glazed ceramic coloured tiles, 400 X 400 X 7mm thick, conforming to IS 15622, Grade B III, on vertical surface of wall such as dados, skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed.

Materials and Labour for Granite (of any type) tiles 18-20mmthick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, over and including 20 mm thick screed bed or bedding layer of cement mortar (1:6), complete all as specified and directed.

Material and Labour for chequered ceramic tiles, coloured, 12 mm thick (square/rectangular) area of each tile exceeding 0.06 Sq M but not exceeding 0.11 Sq M, conforming to IS 4457-2007, on floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour,complete all as specified and directed. MAKE:- (Johnson ‘Endura’/ Somany ‘Durastone’/ Regency ‘Duro’)

Materials and Labour for brick work with Sub Class ‘B’ bricks straight or curved on plan exceeding 6M mean radius built in cement mortar (1:6), complete all as specified and directed.

Materials and Labour for brick work with Sub Class ‘B’ bricks straight or curved on plan exceeding 6M mean radius built in cement mortar (1:4), complete all as specified and directed.

Materials and Labour for brick work with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in built in CM (1:4),complete all as specified and directed.

Materials and Labour for rolled mild steel,Fe 410-W (Grade E-250) Quality-A in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., complete all as specified and directed.

Supply and Fix, Rolled Mild Steel, Fe 410 W (Grade E- 250) Quality-B, in plates (Plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachments, complete all as specified and directed.

M&L for rolled sections as in framing for cladding , glazing and the like fixed with angle cleats and connecting plates etc complete all as specified and directed.

Material and Labour for pre-painted, galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self-tapping screws, complete all as specified and directed.Make(Tata bluescope/Sexena Marine Tech or equivalent make)

Material and Labour for pre-painted, galvalume aluminium zinc coating GI based plain steel sheet, 0.50 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self-tapping screws, complete all as specified and directed.(Tata bluescope/Sexena Marine Tech or equivalent make)

S & F plain, galvanised, 0.80mm thick, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) ) with the grade of Zinc coating 275 with self-tapping screws, complete all as specified and directed.(Tata bluescope/Sexena Marine Tech or equivalent make)

Materials and Labour for mild steel works, conforming to Fe 290, Grade E-165 , in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles, complete all as specified and directed.

Supply and fix mild steel TMT bars 10 mm dia. and over, cut to length, bend to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed

Supply and fix mild steel TMT bars 6 mm to 8mm dia. , cut to length, bend to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed

Supply and fix mild steel TMT bars 5 mm dia. and over up to and including 10 mm dia. in stirrups, spacers, binders etc. cut to length, bend to shape required including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed.

S & F 1.25mm thick MS sheet eaves 250mm wide as in eaves board complete all sepecfied and as directed

Supply and Fix, 20 mm dia. mild steel conduit ,wall thickness 1.00 mm, overall PVC coated including suitable fixing brackets and fancy type end caps as in darpary rod for doors/ windows, complete all as specified and directed.

Supply and Fix, pressed steel frames, size 125 x 60mm, for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified and directed.

Supply and fix Steel windows with side hung shutters including Box/Cylindrical type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed.

Supply and fix Steel windows with side hung shutters including Box/Cylindrical type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, including taking down existing unserviceable one including making good disturbed surfaces as per existing specfication complete all as specified and directed.

Supply and fix Steel windows with side hung shutters including Box/Cylindrical typehinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, including taking down existing unserviceable one including making good disturbed surfaces as per existing specfication complete all as specified and directed.

Supply and fix Steel windows with side hung shutters including Box/cylindrical type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, complete all as specified and directed.

Supply and Fix,steel ventilator with top hung shutter including hinges, steel peg stay, complete without glazing bars, dovetailed or welded, complete all as specified and directed.

Supply and Fix,steel ventilator with top hung shutter including hinges, steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed.

Supply and Fix, 35 mm thick, flush shutters, solid core construction, with particle board core and plywood face panels,both faces is covered with decorative face veneer with lipping/frame to match, complete all as specified and directed.

S&F 2nd class hardwood Glazed and skeleton shutters 35 mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkat complete all as specified and directed

S&F 2nd class hardwood Glazed and skeleton shutters 30 mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkat complete all as specified and directed

Supply and Fix, second-class hard wood timber scantlings, clean sawn, in unframed works and in any position, fixed with nails complete all as specified and directed.

M & L PCC (1:2:4) type B1 using 20mm graded stone aggregate as in hold fast bed block complete all as specified and directed

Supply and Fix, factory made rigid lam PVC door frame of size 125 mm x 50 mm, double rebated with wall thickness of extruded 5mm PVC sheet of density 600 kgs/cum , made by joining 3 Nos. heat bent PVC sheet 'C' channel of 5mm PVC foam sheet of size 35mm x 35mm x 25mm & 40mm x 55mm x 40 mm & 25 mm x 35 mm x 35 mm using solvent cement, the two side 'C' channel shall be reinforced with 19mm x 19 mm MS square tube of 19 SWG with all three 'C' ed to flat base of 5mm PVC sheet with solvent cement. The profile shall be mitred cut at two corners and jointed by inserting 4 Nos. 150 mm long brackets of 15mm x15 mm MS square tube inside the 19 mm square tubes. The two vertical members of door frame shall be reinforced with 40mm x 20 mm MS tubes of 19 SWG duly filled with 2nd class hardwood throughout the frame. The door frame shall be fixed to the wall using 100 mm long nikel coated dry wheet screws through the frame by using PVC fastener. Minimum 08 Nos. of screws shall be provided for each vertical member and minimum 04 Nos.for horizontal members etc. as per manufacturers specifications, fixed in opening, complete all as specified and directed.

Supply and Fix, factory made rigid lam PVC door frame of size 100 mm x 50 mm, double rebated with wall thickness of extruded 5mm PVC sheet of density 600 kgs/cum , made by joining 3 Nos. heat bent PVC sheet sections. The inside section of size 90mm x 30 mm shall be made from colour PVC sheet of 5 mm thickness.The inside section shall be covered by sticking two sections of size 35mm and 6 x 45 mm made from 5mm thick plain sheet. The frame shall be mitred cut at two corners and jointed by inserting 4 Nos. 150 mm long brackets of 15mm x15 mm MS square tube. The two vertical members of door frame shall be reinforced with 40mm x 20 mm MS tubes of 19 SWG duly filled with 2nd class hardwood throughout the frame. The door frame shall be fixed to the wall using 100 mm long nikel coated dry wheet screws through the frame by using PVC fastener. Minimum 04 Nos. of screws shall be provided for each vertical member and minimum 02 Nos.for horizontal members etc. as per manufacturers specifications, fixed in opening, complete all as specified and directed.

Supply and Fix, solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, fixed in opening all as specified and directed.

Supply and Fix, factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded prelam PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail: Panelling of both sides prelam PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, fixed to door frame complete all as specified and directed.

Supply and Fix, factory made wire gauzed PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded prelam PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

Materials and Labour 35mm thick for, Factory Made Solid PVC Moulded Door designer Shutter, with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC sheet on back face, supplying & fixing in frame at site as per specification and drawing, complete all as specified and directed.

Supply and Fix, factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as specified and directed.

Supply and Fix,IS markedStainless steel butt hinges, medium weight, cold rolled 100 mm size complete all as specified and directed

Supply and fix Aluminium anodized barrel tower bolts of extruded section, 100 mm long complete all as specified and directed.

Supply and fix Aluminium anodized barrel tower bolts of extruded section, 150 mm long complete all as specified and directed.

Supply and fix Aluminium anodized barrel tower bolts of extruded section, 200 mm long complete all as specified and directed.

Supply and Fix, aluminium handles, cast type, anodized, 150 mm size, complete all as specified and directed.

Supply and Fix, aluminium handles, cast type, anodized, 125 mm size, complete all as specified and directed.

Supply and Fix,3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane complete all as specified and directed.

Supply and Fix,4 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane complete all as specified and directed.

Supply and Fix, Aluminium Alloy, anodised, sliding door bolt, length of bolt 300 mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Supply and Fix, floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring and with overall length of cover plate 150 mm, fixed in floor, complete all as specified and directed.

Materials and Labour for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290, Grade E-165 complete all as specified and directed.

Supply and Fix, stainless steel wire cloth, 0.36mm nominal dia. of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

Materials and Labour for exposed metal frame ceiling with 6mm thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid with and including exposed metal frame using hot dip galvanised steel, exposed pre-coated ceiling suspension system of grid size 600 mm X 600 mm, with main runner ‘T’ section 24 mm (W) X 38 mm (H) X 0.40 mm (T), cross ‘T’ section 24 mm (W) X 28 mm (H) X 0.30 mm (T) , wall angle 24 mm X 24 mm X 0.43 mm (T) and suspended with 4 mm dia. GI hangers/wire fixed with steel dash fasteners from purlins/soffits spaced at 1200 mm centre to centre with butterfly clips, hold down clips, providing provisions for light fixtures, air conditioning diffuser and ducts, sprinklers, smoke detectors etc., complete all as specified and directed.Make of boards by Ramco industries Ltd and GI grid by Gabson eternity /Armstrong

Materials and Labour for waterproofing treatment to existing RCC roof in the following steps complete all as specified and directed. (i) Providing 15 mm thick screed bed or bedding layer of cement mortar (1:3), mixed with liquid water proofing compound as per manufactures instructions, on concrete surface of roofs or terracing and finishing surface even and smooth without using extra cement. (ii) Waterproofing treatment over smooth finished surfaces after application of cold applied bituminous primer @ 0.30 Kg /Sq M,, providing and laying APP polymer, modified, non-woven polyester fabric of 150 grams/square metre, reinforced membrane, 3.00 mm thick, weighing 3.00 Kg / Sq M, with surface finish of white mineral, by torch on application method, with minimum 75 mm overlap on longitudinal direction and 100 mm overlap on the transverse direction and finally applying with one coat of bituminous based solar reflective aluminium paint @ 100 gms / Sq M complete all as specified and directed.

Materials and Labour for waterproofing treatment to existing RCC roof in the following steps complete all as specified and directed. (i) Complete removal of the existing water proofing treatment. (ii) Wire brushing and cleaning top surface of tiles, lime terracing or cement concrete, including flashings and junction of parapets, etc., and surface painting, with a layer of blown grade bitumen of any penetration applied hot @ 1.7 kg per sq. m, blinded with grit or pea size gravel @ 0.006 cu.m per sq.m, and lightly tampered (area of flashings, etc., shall be added to the roof area) (iiii) Supply and Laying, chicken wire mesh of size 12.5 mm x 0.51 mm (24 SWG) hexagonal construction including all laps, cutting and waste in fabric reinforcement to PCC roof padding including providing 40 mm thick plain cement concrete (1:2:4) type B0using 12.5 mm graded aggregates as in roof padding. (iv) Providing 15 mm thick screed bed or bedding layer of cement mortar (1:3), mixed with liquid water proofing compound as per manufactures instructions, on concrete surface of roofs or terracing and finishing surface even and smooth without using extra cement. (iv) Waterproofing treatment over smooth finished surfaces after application of cold applied bituminous primer @ 0.30 Kg /Sq M,, providing and laying APP polymer, modified, non-woven polyester fabric of 150 grams/square metre, reinforced membrane, 3.00 mm thick, weighing 3.00 Kg / Sq M, with surface finish of white mineral, by torch on application method, with minimum 75 mm overlap on longitudinal direction and 100 mm overlap on the transverse direction and finally applying with one coat of bituminous based solar reflective aluminium paint @ 100 gms / Sq M complete all as specified and directed.

Materials and Labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded aggregates as in plinth protection including finishing surface even and smooth without using extra cement complete all as specified and directed.

Materials and Labour for, broken stone or boulder hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface , complete all as specified and directed.

Materials and Labour for plain cement concrete (1:3:6) type C2 using 40 mm graded aggregate as in surface channels and drains complete all as specified and directed.

Materials and Labour for plain cement concrete (1:2:4) type B1 using 20 mm graded aggregate as in surface channels and drains complete all as specified and directed.

M&L for 25 mm thick damp proof course in CM (1:2:4) mixed with integral water proofing compound @3%by wt of cement with nessery formwork applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m complete all as specified and directed

Filling joints in plinth protection, 30 mm deep x 10 mm wide, filled solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) complete all as specified and directed.

Supply and Fix PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle, of capacity 10 Litres, including brackets, flush pipe, complete all as specified and directed.

Supply and Fix in repair PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle, of capacity 10 Litres, including brackets, flush pipe, complete all as specified and directed.

Supply and Fix, waste coupling of PTMT (half or full threaded) (Minimum weight 45gms), for 32 mm bore discharge pipe,complete all as specified and directed.

Supply and fix PVC connections 15 mm size with PTMT nuts of length 450 mm,complete all as specified and directed.

Supply and Fix, bib tap, cast copper alloy, fancy type, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,15 mm bore and fixed, complete all as specified and directed. Make:Cat No.QQT-7037 of Jaquar or equivalent make of MARC/Kohler)

Supply and Fix, in repair bib tap, cast copper alloy, fancy type, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,15 mm bore and fixed, complete all as specified and directed. Make:Cat No.QQT-7037 of Jaquar or equivalent make of MARC/Kohler)

Supply and Fix, stop valves/Angle cock, cast copper alloy, fancy type, chromium plated,screwed down, high pressure with crutch or butterfly handle, screwed both ends for steel pipe of for unions, 15 mm bore, complete all as specified and directed.Make:Cat No.QQT-7053 of Jaquar or equivalent make of MARC/Kohler)

Supply and Fix, in repair stop valves/Angle cock, cast copper alloy, fancy type, chromium plated,screwed down, high pressure with crutch or butterfly handle, screwed both ends for steel pipe of for unions, 15 mm bore, complete all as specified and directed.Make: Jaquar or equivalent make of MARC/Kohler)

Supply and Fix, stop valves, cast copper alloy , fancy type, chromium plated, screwed down, high pressure with long shank and cup (concealed type), screwed both ends for steel pipe of for unions, 15 mm bore, complete all as specified and directed.Make:Jaquar /Marc/Kohler)

Supply and Fix,in repair stop valves, cast copper alloy , fancy type, chromium plated, screwed down, high pressure with long shank and cup (concealed type), screwed both ends for steel pipe of for unions, 15 mm bore, complete all as specified and directed.Make:Jaquar /Marc/Kohler)

Supply and Fix, pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe, 15 mm bore, including taking down existing unserviceable one complete all as specified and directed.Make:Cat No.QQT-7011 of Jaquar or equivalent make of Marc/Kohler)

Materials and Labour for galvanized steel tubing, medium grade, 15 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, complete all as specified and directed.

Materials and Labour for galvanized steel tubing, medium grade, 20 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor,or trench complete all as specified and directed.

Refixing all serviceable 15mm dia GI tubing and connection with new fittings solid fitting in new or old position on wall/floor complete all as specified and directed

Refixing all serviceable 20mm dia GI tubing and connection with new fittings solid fitting in new or old position on wall/floor complete all as specified and directed

Supply and Fix, brass chromium plated shower rose 125mm size,with swivel joints, fixed to steel pipe or union 15 mm bore, complete all as specified and directed.Make:Cat No.MSR-1060 of Marc or equivalent make of Jaquar/Kohler)

S&F in repair 75mm bore chromium plated shower rose with shower arm of 15mm dia (size of arm 195mm long with bend to 45 degree) complete all as specified and as directed (Make: Jaquar/Marc/Kohler)

Supply and Fix, brass chromium plated, towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and directed.Make Cat no.AKP 35711P of Jaquar or equivalent of Marc/Kohler

S&F towel rail 450mm long of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats (Minimum weight 190 gms) all complete as specified and as directed. (Make: PRINCE/PRAYAG).

S&F 500 ltrs IS marked multilayer rotational moulded polythytene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position with and including 20mm PTMT ball valves high pressure with polythene float and nut complete all as specified and directed .

S&F vitreous china squating pan orissa pattern size 580x440 mm white with integral foot rest complete including lime concrete (excl flushing cistern and flush pipe )but connecting to flushing pipe , anti symphonage pipe etc complete all as specified.

S&F vitreous china squating pan orissa pattern size 580x440 mm white with integral foot rest complete including lime concrete (excl flushing cistern and flush pipe )but connecting to flushing pipe , anti symphonage pipe etc with and including lime concrete bedding and demolition of existing one complete all as specified.

S&F vitreous chaina wash hand basin 550x400mm (flat back type) including cutting for and pinning in ends of brackets with and including waste fittings, CP pillar tap with capstan head, and waste water pipe complite all as specified and as directed.

S&F in repair vitreous chaina wash hand basin 550x400mm (flat back type) including cutting for and pinning in ends of brackets with and including waste fittings, CP pillar tap with capstan head, and waste water pipe complite all as specified and as directed.

Supply and fixed in repairs vitreous china bowl urinal (Flat back or corner wall type) of size 465 x 355 x 265mm (minimum) white with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, grating and union for discharge pipe all complete as specified and as directed. (Make : HINDWARE/PARRYWARE)

M & L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth in brick walls

M&L 100mm bore cast iron floor trap plain with grating including jointing to waste pipe fixed in cement concrete type B-1(1:2:4) all complete as specified and as directed

Supply and Fix, 110 mm bore UPVC (SWR) pipes, single socketed in any length with rubber ring joints,laid in trenches or in floors, complete all as specified and directed.

Supply and Fix,110 mm bore UPVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls, complete all as specified and directed.

Supply and Fix,75 mm bore UPVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls, complete all as specified and directed.

Supply and Fix, 75 mm bore PVC (SWR) bends any radius, with access door, complete all as specified and directed.

S&F PVC (SWR) vent cowl 110 mm bore complete.

S&F PVC (SWR) vent cowl 75 mm bore complete.

S&F 110mm dia PVC(SWR) junction single, (single T) equal or unequal with access door complete all as specified and as directed.

M&L PVC gully trap125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

Supply and Fix, PVC (SWR) floor trap, plain with grating including jointing with solvent cement with dia. of out let 75 mm, complete all as specified and directed.

M&L concrete bed PCC (1:3:6) type C2 to drain pipes including packing under & haunching against sides of pipe after they are laid & tested for 110mm bore pipe complete all as specified and directed

Supply and Fix, in repair soap dish, fixed in wall, complete all as specified and directed.Make Catpart no.AQN-7731 of Jaquar or equivalent make of Kohler/Marc

Cutting of existing GI pipe 80mm bore dia in position for taking out branch connection of 20mm bore(dia) inserting 1 No Tee of size 80x80x20mm including providing new reducing Tee all joints and jointing materials, necessary exc and earth work complete all as specified and dircted

Supply and Fix, gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe, 20 mm bore, complete all as specified and directed.

Material and Labour for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel and iron surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

Material and Labour for applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

M&L for rendering 5mm thick plaster in cement mortar 1: 3 on fair faces of concrete surfaces such as soffit of slab, beam, ceiling etc including finishing the surface even & smooth complete all as specified and directed

Materials and Labour for rendering 15 mm thick, cement plaster, in cement mortar (1:6) on surface other than fair face of brickwork in walls and finishing surface even and smooth without using extra cement, complete all as specified and directed.

Materials and Labour for rendering 5 mm thick, cement plaster, in cement mortar (1:4) mixed with water proofing compound as per manufactures instructions over and including 10mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surface in walls, complete all as specified and directed. Note: - (Water proofing compound will be measured and paid separately)

Supply only integral water proofing compound conforming to IS: 2645 - 1975 specification complete all as specified and as directed (Make : CICO No- 1/SIKA/ACCO PROOF).

Materials and Labour for applying applying two coats of acrylic distemper, white or tinted, to new plastered surfaces on walls, over and including 3mm thick wall care putty premium quality over priming with alkali resistant priming paint and including preparation of surfaces, complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

Material and Labour for applying two coats of cement-based paint, white or tinted over and including alkali resistant primer to new plastered surfaces on walls,including preparation of surfaces complete all as specified and directed.

Material and Labour for applying two coats of white wash to old un -decorated plastered surfaces on walls including preparation of surfaces complete all as specified and directed.

Material and Labour for applying three coats of white wash to new plastered surfaces on walls including preparation of surfaces complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Taking down unserviceable existing XLPE cable any description removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Supply,laying, jointing and testing of LT, XLPE insulated, PVC sheathed, armoured, heavy duty electric cables with aluminium conductor for working voltage up to and including 1100 volts, of cross sectional area 16 sq. mm, 2 core, including with suitable size of lugs complete all as specified and directed.

M&L for concealed type wiring using approved colour coding as per IS for one light/ fan/ bell point controlled by one switch with1.5 Sqmm (Nominal area) PVC insulated, unsheathed, multistranded copper, conductor cable FRLSH (1100Volts grade) drawn in and including PVC rigid conduits of 20/25 mm dia with all fittings and accessories alongwith PVC insulated standard copper conductor of size 1.5 Sqmm as earth continuity conductor including fixing of 1. 22mm thick MS sunk terminal box duly flushed to wall with 3mm thick plastic laminated/ebonite sheet cover fixed with brass screws,cap and washers complete all as specified and as directed. Note:- (i) The chases in the wall shall be cut with elect cutter (ii) The disturbed surfaces of wall shall be made good with cement plaster 1:4 including matching the surfaces with as per existing finishes and to the entire satisfaction of Engineer in Charge

All as per item No-166 as above but for one 3/5 pin socket outlet 5 Amps on the same board with other switches.

All as per item No-166 here-in-before but for switch socket combination 5 Amps 2/3/5 Pin point on independent board.

All as per item No-166 here-in-before but for switch socket combination 15 Amps 3/6 Pin on independent board with 2.5 Sqmm (Nominal area) PVC insulated unsheathed, multistranded copper conductor FRLS cable (1100Volts grade) complete.

Supply and Fix, switch piano, flush button, single pole, one way, 5 Amps, complete all as specified and directed.

S&F modular switch 6 Amps single pole one way one module with top cover all as specified and as directed (Make: Legrand Model:-Myrius Cat No : 6730 84 or equivalent model of L&T/ Havells (Crabtree).

S&F modular switch 16 Amps single pole one way one module with top cover all as specified and as directed (Make: Legrand Model:-Myrius Cat No : 6730 86 or equivalent model of L&T/ Havells (Crabtree)

M & L for Switch socket combination, 6 pin, 6A, 3 module with top cover all as specified and as directed (Make: Legrand equivalent model of L&T/ Havells (Crabtree)

M & L for Switch socket combination, 6 pin, 16A, 3 module with top cover all as specified and as directed (Make: Legrand equivalent model of L&T/ Havells (Crabtree)

S&F modular fan regulator 120 watt 240 volts AC two module all as specified and as directed. (Make : Legrand model – Myrius Cat No 673092 or equivalent model of North West/Crabtree).

Supply and Fix, switch piano, flush button, single pole, one way, 15 Amps, complete all as specified and directed.

Supply and Fix, ceiling rose, three terminal, PVC/ Polycarbonate insulated body, complete all as specified and directed.

Supply and Fix stepped type electronic fan regulator, flush type, on existing phenolic laminated sheet etc. as required , complete all as specified and directed.

Supply and Fix lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings,complete all as specified and directed.

Supply and Fix lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings with including LED lamp , 15 Watts, , colour temp 6500 K, lamp current 0.04 amp, lamp base cap B22 ,complete all as specified and directed.

Supply and Fix, LED lamp, 10 Watts, lumen output 770 lm, colour temp 6500 K, lamp current 0.04 amp, lamp base cap B22, complete all as specified and directed.

Supply and Fix, socket outlet 2 in 1, 5 pin, 5A, complete all as specified and directed.

Supply and Fix, socket outlet 2 in 1, 6 pin, 5 and 15 amp flush type, complete all as specified and directed.

Supply and Hanging, ceiling fan, rating 240 V, 50 Hz, Single Phase, 1400 mm sweep with down rod, canopy, fan blades and accessories, BEE 5 Star Rated, all as per Model “ES-50 Premium 5” of Make ‘Havells’ or equivalent Model of Make ‘Usha’/’Crompton Greaves’/’Almonard’ , and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 1.50 Sq mm, 3 core, 1100 Volts grade, from ceiling rose/ connector to fan complete all as specified and directed.

Supply and Fix, Heavy Duty Exhaust Fan, 380 mm sweep, 1400 RPM, Single Phase, 230 V, 50 Hz, all as per Model “Turbo Force” of Make ‘Havells’ or equivalent Model of Make ‘Usha’ / ’Crompton Greaves’/’Almonard’ and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 2.50 Sq mm, 3 core, 1100 Volts grade, from ceiling rose/ connector to fan complete all as specified and directed.

Supply and Fix, Heavy Duty Exhaust Fan with self closing metallic louvers, 300 mm sweep, 1400 RPM, Single Phase, 230 V, 50 Hz, all as per Model “Turbo Force” of Make ‘Havells’ or equivalent Model of Make ‘Usha’ / ’Crompton Greaves’/’Almonard’ and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 1.50 Sq mm, 3 core, 1100 Volts grade, from ceiling rose/ connector to fan complete all as specified and directed.

Cutting openings, through brick walls built in cement mortar or cement lime mortar, for exhaust fan and other openings or enlarging existing openings,superficial area exceeding 0.16 Sqm but not exceeding 0.25 Sqm, making good distrubed portion, grouting of suitable bolts with nuts & washers for fixing exhaust fan,rendering 15 mm thick plaster in CM (1:4) around jambs of opening, complete all as specified and directed.

S&F Decorative ultra slim linear LED lighting fixture with co extruded polycarbonate body environmental friendly, 20W, 240 Volt, LED tube light as per Havells Cat No. LHEYBYP6OE1W020 or equivalent of philips/Bajaj/wipro.

Supply and Fix, decorative LED tube light fitting with extruded polycarbonate housing,20Watts,colour temp 6000 K, all as per Cat No. LHEXBHP7IN1W020 of Make ‘Havells’ or Equivalent Model of Make Bajaj/Philips and including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.50 Sq mm, 3 core, 1100 Volts grade, from light fitting to point outlet, complete all as specified and directed.

S & F 25 Watt 230 volt 50 Hz LED type new generation energy saving building security light luminiries housing is of versatile pressure die cast aluminium IP 66 with high power LED light complete with ballast/charging unit including of all accessories prewired including connecting up with 2.5 sqmm multi stranded aluminium conductor 2 core cables not less than 2 m of length fixed to pole/wall etc and testing with and including 1.5mtr GI pipe 40mm dia light grade bracket bend to shape ,clamps,nuts,bolts and washer complete all as specified and directed. Make: Wipro cat part No. LR02-291-XXX-57-XX or equivalent of philips/CG.

S & F 35 Watt 230 volt 50 Hz LED type new generation energy saving building security light luminiries housing is of versatile pressure die cast aluminium IP 66 with high power LED light complete with ballast/charging unit including of all accessories prewired including connecting up with 2.5 sqmm multi stranded aluminium conductor 2 core cables not less than 2 m of length fixed to pole/wall etc and testing complete all as specified and directed. Make: Wipro cat part No. LR02-391-XXX-57-XX or equivalent of philips/CG.

Supply and Fix, miniature circuit breaker (MCBs), single pole and neutral, 240 Volts,10KA, 40 Amps C- curve series complete all as specified and directed.

Supply and Fix, miniature circuit breaker (MCBs), single pole, C-curve 240 Volts,10KA, 6-32 Amps complete all as specified and directed.

Supply and Fix, miniature circuit breaker (MCBs),TPN, 415 Volts,10KA, 63- Amps complete all as specified and directed.

Supply and Fix, double door, sheet metal enclosure for DBs for mounting of MCB for 415 Volts, 8 way, with 200 Amps rated bus bar, Single Pole & Neutral, including blanking plates as required & flush to wall complete all as specified and directed. [Cat No.DBSPN008DD of Make L&T or equivalent Model of Make Legrand/Siemens]

Supply and laying in tenches/pipes/along wall/roof/across drain/culvert XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade, cross sectional area 10 Sqmm 2 core including with suitable size of Aluminum lugs complete all as specified. Make : Havells//KEI/RR Cable

Supply,laying, jointing and testing of LT, XLPE insulated, PVC sheathed, armoured, heavy duty electric cables with aluminium conductor for working voltage up to and including 1100 volts, of cross sectional area 25 sq. mm, 2 core, complete all as specified and directed. Make : Havells//KEI/RR Cable

Supply and filling in approved dry sand in cable trenches before and after the cables are laid, as in sand cushioning to cables, complete all as specified and directed.

Supply and Laying galvanized steel tubing, 40 mm bore, light grade, in trenches or fixed to poles/Walls etc., for cable protection, complete all as specified and directed.

Supply and laying common burnt clay building bricks, sub-class ‘B’ designation 75, old size bricks, in cable trenches, as cable protection, complete all as specified and directed.

Materials and Labour for earthing complete with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.5M below normal ground level connected to galvanised steel earth lead wire 4 mm dia. by means of bolts, nuts check nuts and washers of galvanised steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm centre to centre both ways, with one handle for lifting made out of 8 mm dia. MS bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 15 mm bore galvanized steel tubing medium grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown on electrical plate No 3 of SSR Part –I (2009)

M.C.Baruah