Construction of additional floor of Girls Hostel at Fisheries College and Research Institute Thoothukudi

Amount

Dismantling R.C.C by manual/by using deploying machineries

Dismantling, clearing away and carefully stacking materials for re-use for any thickness of brick or stone masonry walls in cement mortar under 3.0m high.

Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts and clearing and levelling the site, etc. ,complete complying with standard specification.

Supplying and filling in foundation, basement, etc with filling M-sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Plain cement concrete 1:4:8 using 40mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification.

Supplying and filling in 'foundation and basement with filling good quality earth in layers of not more than 15cm.thick well rammed watered and compacted etc.,complete complying with standard specification.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering and shuttering for soffits including necessary supports and strutting upto 3 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at above 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specification.(Payment for cantering shall be given after the concrete is laid).

Plain surfaces such as roof slab, floor slab, beams , lintels , loft, sill slab, staircase waist , portico slab and other similar works.

Square and rectangular columns and small quantities such as sunshades ,parapet cum drops,window boxing,fin projections and other similar works.

Supplying and placing of Ready Mix M30 grade -360 KG/CUM minimum cement content of with OPC 53 Grade of Concrete confirming to IS 456/2000 for Reinforcement Cement Concrete Structural elements under controlled water cement ratio using 20mm and down graded machine broken granite stone jelly including transportation and pumping excluding cost of centring and shuttering and reinforcement but including curing, finishing etc as directed by departmental officers.

Foundation and basement

For First floor

For Second floor

Supply, fabrication and placing of reinforcement steel of high yield strength ribbed bars of various diameters and grade conforming to IS 1786 for reinforced concrete work. The work includes de coiling, straightening, cutting, bending, fabricating, and placing in position, at all levels including lead and lift, according to drawings, specifications etc. complete and supply & use of 18G black annealed binding wire double fold to tie the bars in position and providing precast cement/ PVC cover blocks for main reinforcement to ensure specified cover and complete., including all labour charges etc as directed by departmental officers.

Brick work in Cement Mortar 1:5 (one cement ,five M sand) using best quality third class country bricks of size 83/4" x 41/4 x 2-3/4" including curing etc., complete complying with standard specification. including scaffolding curing cost of reinforcement etc. all complete as per specifications and drawings as directed by the Engineer in-charge.

First floor

Sedond Floor

Brick Partition :Providing and constructing 108mm thick brick masonry in cement mortar 1:3 for partition walls using well burnt best quality third class country bricks of size 8-3/4x4-1/4x2-3/4including supplying and laying 1 No 6mm dia MS bars at every fourth layer including scaffolding curing cost of reinforcement etc. all complete as per specifications and drawings as directed by the Engineer in-charge.-first floor

Special ceiling plastering in Cement mortar 1:3 ( One part of Cement and Three parts of Sand )10 mm thick to finish the exposed surfaces of R.C.C. items of works such as Roof (or) floor slabs, beams,and Sun shades etc.to correct plane and level including scaffolding, hacking of surface,chiselling the undulated surface wherever necessary and curing etc.,all materials and labour complete in all respects including all lead,lift and descent and as directed by the Engineer in charge.This rate includes the cost of providing Cement Mortar beadings for sun shades, steps,landing slabs,elevation etc.complete complying with standard specifications.

Providing & applying 12 mm thick cement plaster in CM 1:5 (1 part of cement: 5 parts of sand) to walls internally and externally in single coat at all levels to correct line and level including chicken wire mesh at all joints of brick and concrete surfaces with minimum overlap of 150 mm in all directions, scaffolding, rounding off or champhering of corners, offsets, fin/ bands, projections, etc. and cleaning of surface, raking out joints, roughening of surface, chiseling the undulated surface wherever necessary and curing, etc., all materials and labour complete in all respects including all lead, lift and descent and as directed.

Providing Band cornice work 230mm wide and 50mm deep using country brick in cement mortar 1:4 (one cement , four river sand ) plastered with cement mortar 1:4 (one cement , four river sand )12mm thick including rendering smooth with cement at 22.5 Kg per 15m length curing ,necessary scaffolding and centring etc. complete as directed during execution.

Paving the floor with best quality double charged Vertified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Flooring with following Anti skid ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / Sqm. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works).

Dadooing the walls with colour glazed tiles of size 300mmx450mm x8mm approved size , quality and colour set in CM 1 : 2 - 10 mm thk. And pointed with suitable cement including finishing the joint and pointing flesh with walls and tile surface in all floors at the rate of 0.40 Kg /Sqm etc. complete.

Dadooing the brick walls with wire cut brick tiles 10mm thick with sunken pointing ,laid over 10mm thick or more cement mortar (to make up required finished level) in mix 1:3,joints filled and finished neat with pigmented white cement including cutting ,laying etc. complete including clamp supporting and labour charges etc.

Providing and laying 18mm /20mm thick fine polished (flamed steel grey) granite for steps & Landing of approved size and pattern in CM 1:3(one cement and three M sand) including nosing where ever necessary as per drawings and specifications and as directed by the Engineer in charge.

Supply and fixing of polished granite (paradise,synthetic grey granite) slab ,18 mm/20mm thick, for flooring including fixing in position cutting , chipping the wall, masonry touch up works etc., complete in all respects for all floors as directed by the departmental officers.

Providing, fabricating and fixing M.S. grills Windows, and ventilator, gates, ladders, rail pipes, nosing angles, with M.S.lugs in staircase steps etc., made out of M.S rods, flats, angles, pipes, channels etc.with one priming coat including necessary fixtures complete as per drawings and specifications and as directed by the Engineer.

Manufacturing,supplying and fixing of stainless steel hand rails for staircase using 50mm dia 304L grade stainless steel pipe of 1.6mm thick will be provided with tubular supports made of 304L grade ss pipe of 25mm dia of 1.6mm thick welded to the railing.The supports will be grouted into the wall and provided with 93mm thick ss circular base plate of 304L grade.The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, cutting, grinding, conveyance,welding charges,electrical charges,etc.complete.

UPVC Window supplying and fixing UPVC ( Un-PLASTICIZED Polyvinyl chloride) windows of casement type (open) from the profile the size of outer frame 60mmx58mm and shutter profile are reinforcement with gi/1mm 125GSM and 100% corrosion free, the profiles are multi chambered section with wall thick of 2mm.The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power points locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sah and outer frame that enables opening of the window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames The window should be got approved from the Executive Engineer before use on work.

UPVC VENTILATOR:Supplying and fixing UPVC (Un-PLASTICIZED Polyvinyl chloride)Louvered Ventilators of from the profile the size of outer frame 60x58mm and shutter profile the size of 60x78mm both profile size of 60x78mm both profiles are reinforced with GI/1MM 125GSM and 100% corrosion free,the profile are mulit chambered sections with wall thick of 2mm.The EPDM rubber ( black colour) covered with all over he edges of frame and shutter.The corners and joints should be welded and cleaned.Radiation pin headed glass 4mm thick should be fixed to the wall with 100% packing with screws and silicon packing all aroundthe frame.The ventilator should be got approved from the Executive Engineer before use on work.

Solid PVC door shutters Toilet door using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings .The over all size of styles shall be 50mm x 30mm.The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm.The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter.

Door Frame: Supplying and fixing first quality teak wood frames for doors, windows, ventilators and other similar joinery works with the following sizes and sections including labour charges for wrought and put up in position and also for fixing hold fast in frames and masonry etc. complete in all floors.

Teak wood Scantlings up to 2M

Teak wood Scantlings over 2M and below 3M

Supply & Fixing of 35mm single leaf high density interior grade marine plywood shutters pasted both sides with 4mm thk.OST ply of approved design with 35x12mm T.W.lipping on all edges with necessary adhesives and CP screws complying with standard specification. The cost is inclusive of 1 no mortise lock ,Handle, tower bolt , approved equivalent make SS bearing hinges of equivalent make of approved make,2 no floor mounted SS door stoper ect. complete.

Supply & Fixing of 35mm double leaf high density interior grade marine plywood shutters pasted both sides with 1.5mm thick .laminate approved design with 35x12mm T.W.lipping on all edges with necessary adhesives and CP screws complying with standard specification. The cost is inclusive of 1 no cylenderical lock ,Handle, tower bolt , approved equivalent make SS bearing hinges of equivalent make of approved make,2 no floor mounted SS door stopper etc. complete.as per drawing

Toilet Sunken using broken brick jelly 20 mm gauge The proportion of broken brick jelly to slaked lime being 1:3:6 (1part cement,3 part fine aggregate & 6 part broken brick jelly), well beaten by wooden beaters for giving required slope and thickness required etc complete complying with standard specifications and as directed by Departmental Officers. -First floor

Manufacturing, supplying and fixing of Steel doors (Double leaves) with following specification.MS angle of size 40x40x6mm at 3.5 kg/m used for outer frame and MS Angle of size 35x35x5mm at 2.6 Kg/m for the shutter frame. Stiffeners with 32x6mm at 1.5 Kg/m MS Flat is provided as the lock rail of the door and welded intact on both ends to the shutter frame.18 G CR Sheets of best quality is laid as panel in the shutter frames. 18x5mm at 0.70 kg/m MS flat is welded over the 32x6mm at 1.50kg/m MS Flat on the rear side of the door, sandwiching the CR Sheet for rigidity. Additional stiffeners with 18x5mm at 0.7 Kg/m MS flats are provided diagonally on the rear side of the shutter. 300mm length of hinges 2Nos, for shutter is provided.6 Nos. of 250mm length hold fasts 200mm length specified at the ends are welded to the outer frame of the door. Tower bolt 2 Nos. at the top provided.

Painting two coats of synthetic Enamel paint of approved colour and make over one coat of anti-corrosive Zinchromite primer over new wood / steel work, suitably prepared for receiving the paint by surface scraping, rubbing applying filler etc. including cost of filler, primer, paint all complete as per drawings and specifications.

Painting two coats of synthetic Enamel paint of approved colour and make over one coat of wood primer over new wood suitably prepared for receiving the paint by surface scraping, rubbing applying filler etc. including cost of filler, primer, paint all complete as per drawings and specifications.

Providing and applying Emulsion paint finish of approved make & shade in two or more coats over a coat of approved primer to give an even shade as per manufacturer's instruction to the plastered surfaces and Internal ceiling plastered surfaces including preparation of surfaces, scaffolding etc. all complete as per drawings and specification for all heights.

Providing and applying Emulsion paint finish of approved make & shade in two coats over a coat of approved primer and 2 coats of putty to give an even shade as per manufacturer's instruction to the Internal Wall plastered surfaces including preparation of surfaces, scaffolding etc. all complete as per drawings and specification for all heights.

Supplying and painting the walls with one coat of wall primer and two coats of Exterior emulsion (apex or equivalent) as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications (The colour and shade of the cement paint shall be got approved by the Executive Engineer before use of work).

Supplying and preparing surfaces plaster walls, RCC surfaces and applying approved quality of Texture external plastered surfaces and two coats emulsion and one coat primer to ll levels including preparation of surfaces ,scaffolding etc., all complete as per drawing and specification for all heights.

Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.

Providing and laying polymer coated Water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C.,toilet and the like ) Ist course of applying cement slurry @ 4.4 Kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. ii) IInd course of 20mm cement plaster 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7Kg. per sqm of area. iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/sqm.)

Providing, supply, mixing laying cement plastering 20mm thick with cement mortar 1:3 mixed with Water proofing compound Conplast X421IC conforming to IS:2645, @ 150ml per bag of cement (normal setting integral water proofing compound) as specified by the manufacturer over PCC levelling course including preparation of surface, dewatering, finishing, curing etc. all complete as per manufacture's Specification and direction etc.,

Supplying and fixing in position C.I.Manhole covers (heavy duty) mof various sizes of best approved quality and as per standard specificationsetc., complete.0.6X0.6M Size etc., complete.

Foot rest fixing inside the sump including labour charges etc., complete.

Providing, granolithic flooring in cement concrete mix of 1:2:4 (1 Cement: 2 Sand: 4 Aggregate 10 to 12 mm thick) well vibrated, compacted including 45 X 3 mm glass dividing strip, fixed to correct level and finished smooth and cured by keeping surfaces well-covered and protected against excess of an type. (The contractor to provide for preparation of surface by cleaning, hacking and exposing aggregate to achieve the best bond and any curling, lifting or beybonding noticed shall be rectified by the contractor at his cost).-40 mm thick

Supplying and fixing fine polished cuddapah slab of following thickness for cup-board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as direct. 20 / 30mm thick

Providing Cup-board Shutter using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydraulic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer before use on work.

Supplying and fixing colour galvalume sheet roof of 0.47mm thick and steel tubular box section of 100x50x3mm of 1meter interval including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing white glazed Indian water closet, Orissa pattern, with dual flush (3 & 6 lit) PVC cistern mounted on wall, Parryware or equivalent, with PVC, P or S trap having 100mm dia outlet and 50mm deepwater seal, embedding trap and water closet in cement concrete in 1:4:8 mix.

Supplying and fixing in position white glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings..... such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)

Supply & Fixing of two in one CP Health Faucet of the closet mounting type with hose connected two way BIB COCK complete fittings. (Make: Parryware or equivalent)

Supplying & fixing of Coat hook with brackets including fixing over Wall tile dado / door shutter using suitable size non-corrosive screw nails etc. complete.(Make: Parryware or equivalent)

Supplying and fixing in position best quality and approved make Indian made colour glazed earthen ware wash basin of Size - 550 X 400mm with brackets / G.I. rag bolts and nuts painted, 32mm dia brass C.P. waste coupling, (heavy) 32mm dia brass C.P. bottle trap, 15mm dia brass C.P. Angle stop cock with flange, 15mm dia brass C.P. cold water connecting pipe, etc., The work shall include, required extension nipples, cutting / chasing and making good the walls and floors - toilets.

Supplying & fixing of Angle valve stopcock with connecting hose and wall flange. (Make: Parryware or equivalent)

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks).

PART - B SOIL, WASTE AND VENT PIPE LINES : Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages,etc., complete complying with standard specifications.(The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level.

40mm dia. 6kg class PVC pipes.

50mm dia. 6kg class PVC pipes.

75mm dia. 6kg class pipes.

110mm dia. 6kg class pipes.

Supplying and fixing in position PVC nahini /Floor Trap with PVC Grating type of size 100x75 mm with best quality gratings of approved brand fixed over a bed of brick jelly lime concrete 1:2:5(One lime two sand and five aggregate) brick jelly 40mm and finishing with CM 1:3(One cement and three sand)wherever found necessary and making good to the original condition and giving connections to the PVC pipes etc., complete complying with standard specification and as directed by the Departmental Officer.

Supply and fixing in position best quality PVC IS 4985 - CLASS-II - 4 Kg/Sqcm -Rain water pipes of various size having ISI mark and providing leak proof joints with such as Bend, Tee Junction, door etc.,of approved quality including fixing to the wall with special PVC /MS clamps, etc., and making connection to all sanitary fittings, wherever necessary and making chipping good to the original condition, complying with standard specification etc., complete.-110mm dia. 4ksc class pipes.

Supplying and fixing in position of the following dia PVC rain water gratings for rain water pipes ,of approved quality and variety of various size confirming to ISS and including necessary cutting and fixing and giving connection to PVC pipes etc., complete complying with standard specification and as directed by the Departmental Officers

75mm x 50mm

100mm x 75mm

Supplying and fixing in position of the following dia PVC specials such as PVC vent Cowl etc.,of approved quality and variety of various size confirming to ISS amend providing leak proof joint etc., including necessary cutting and fixing and giving connection to PVC pipes etc., complete complying with standard specification and as directed by the Departmental Officer

75mm dia

110mm dia

D. WATER SUPPLY SYSTEM : Providing, supplying & laying of Chlorinated Poly Vinyl Chloride (CPVC-SDR-11) Pipes conforming to IS 15778 having thermal stability cold water with brass and CPVC fittings like Elbow,Brass Tee, Brass Elbow,Offsets,Tee with clamps @1.00 meters spacing, with jointing of pipes with one step CPVC solvent cement with including cutting of chase including testing of the joints complete and making good the walls etc. Rate is inclusive of all material labour, transportation ,tools & tackles taxes, levies VAT etc all complete as per as per specifications, Concealed work including chase cutting) complete complying with standard specification and as directed by the Departmental Officer. (Commercial application) internal concealed works.

20 mm nominal (OD) pipes

25 mm nominal (OD) pipes

32 mm nominal (OD) pipes

Providing, supplying & laying of Chlorinated Poly Vinyl Chloride (CPVC-SDR-11) Pipes conforming to IS 15778 having thermal stability cold water with brass and CPVC fittings like Elbow,Brass Tee, Brass Elbow,Offsets,Tee with clamps @1.00 meters spacing, with jointing of pipes with one step CPVC solvent cement with including cutting of chase including testing of the joints complete and making good the walls etc.Rate is inclusive of all material labour,transportation,tools & tackles taxes, levies VAT etc all complete as per as per specifications, Exposed work including chase cutting, bracket fixing)complete complying with standard specification and as directed by the Departmental Officer. (Commercial application) exposed plumbing works

20mm nominal(OD) pipes

25mm nominal(OD) pipes

32mm nominal(OD) pipes

40mm nominal(OD) pipes

Providing, supplying & laying of Chlorinated Poly Vinyl Chloride (PVC) Pipes conforming to IS 15778 having thermal stability cold Metro water with brass and PVC fittings like Elbow, Brass Tee, Brass Elbow, Offsets, Tee with clamps @1.00 meters spacing, with jointing of pipes with one step PVC solvent cement with including cutting of chase including testing of the joints complete and making good the walls etc. Rate is inclusive of all material labour, transportation, tools & tackles taxes, levies VAT etc all complete as per as per specifications,Concealed work including chase cutting) complete complying with standard specification and as directed by the Departmental Officer. (Commercial application) - External plumbing works

32 mm nominal (OD) PVC pipes

110 mm nominal (OD) PVC Pipes(TWL)

Supplying and fixing of PVC ready made HDPE water storage tanks made of PVC matertials including necessary provision for conveying, jointing delivery line etc. Complete.should be got approved by the Executive Engineer before use on works

Supplying and Erection and construction of sewer chambers of required internal dimensions 600x600 upto 0.6 mtr.depth with 230mm brick masonry in C.M.1:5 thk of masonry over bed of 1:2:4 R.C.C. 200 mm thk above 100 mm thk P.C.C.1;3:6 Cement concrete foundations over sand bed of 100mm thk channelling in 1;2:4 cement concrete, plastering in 1:3 cement mortar for internal and external surface finished with floating coat of neat cement, the work including excavation for required depth of gully trap and refilling and making good in the surface with SFRC cover and frame 600x600mm (clear opening) complete complying with standard specifications etc.,

Construction of rain water recharge well of 1200mm dia and depth upto 1500mm, in addition 110 dia special blue slotted pipe for borewell pipe should be laid from bottom of ring well centre to centre to below 1500mm as shown in the drawings ,including all types of excavation, occur for pipe , filling of rain water harvesting materials with construction of R.C.C ring and top 100 mm RCC slab with 450x450mm perforated SFRC manhole and 230mm brick wall in 2'height with below 300mm length x100mm tk. PCC as per the structural filling the filter media as per drawing

Supply and run of 2 of No.8 SWG G.I wire for guarding with gradle with No.8 SWG G.I wire at the equal interval of 1.5 Metre.

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / Supports on wall / floor / ground for earth connection.

DISTRIBUTION BOARD: Supply and fixing of triple pole and neutral 12 way7 segments MCB distribution board complete with the following and necessary neutral link, earth connector link etc. with bus bar and double door arrangements on surface / in flush with wall and making good of the concealed portion with earth connection Incoming: 1 No. 63A 10KA 4 pole MCB -1 NO. 3 nos of 63A/100mA DP RCCB Outgoing: 36 Nos. 6/10A 10KA SP MCB FOR LDB CUM PDB

MAINS WIRING

Supply and run of 4 of 10(140/0.0.3) Sqmm & 2 of 2.5 36/0.3) PVC insulated SC Multistrand copper cable of 1100V grade in suitable PVC rigid pipe concealed in Wall and ceiling with continuous earth wire and making good of the concealed portion with suitable colour LIGHTING / POWER DB

Supply Wiring, run Connecting, Testing & Commissioning of 2 of 6 sq.mm PVC Insulated SC Unsheathed CU.Condutor of 1100V Grade in Suitable PVC Rigid Pipe Concealed in Wall and Ceilling With Continous Earth Wire Connection of 2.5 Sq.mm PVC insulated Sc CU.Condutor and making Good of the Concealed Portions With Suitable Colour. FOR ROOMS MAIN WIRING

Supply Wiring, run Connecting, Testing & Commissioning of 2 of 4 sq.mm PVC Insulated SC Unsheathed CU.Condutor of 1100V Grade in Suitable PVC Rigid Pipe Concealed in Wall and Ceilling With Continous Earth Wire Connection of 2.5 Sq.mm PVC insulated Sc CU.Condutor and making Good of the Concealed Portions With Suitable Colour. (Raw power 6/16Amps Socket and split AC unit point wiring 1.50TR unit)

Supply and Run of 3 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection with painting of suitable colour. (light point, mains wiring, RAW power 6/ 16Amps socket wiring)

POINTS WIRING

Wiring, Connecting, Testing & Commissioning with 3 X 1.5sqmm PVC insulated single core unsheathed copper conductor cable of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceilling with PVC accessories, including supply and fixing of modular 6A one way switch along with moulded front plate in G.I anodised manufaturer's mounting box fixed flush with the wall complete with all accessories as required light points. (length of the points will be 5 to 8 metres)-Light points

Additional light point wiring (looping from first light point to next point maximum length is 3-5m))

Wiring, Connecting, Testing & Commissioning with 3 X 1.5sqmm PVC insulated single core unsheathed copper conductor cable of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceilling with PVC accessories, including supply and fixing of 2 Nos. modular 6A two way switch along with moulded front plate in G.I anodised manufaturer's mounting box fixed flush with the wall complete with all accessories as required as per the site condition.

Wiring, Connecting, Testing & Commissioning with 3 X 1.5sqmm PVC insulated single core unsheathed copper conductor cable of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceilling with PVC accessories, including supply and fixing of modular 6A one way switch, one step type fan regulator along with moulded front plate in G.I anodised manufaturer's mounting box fixed flush with the wall complete with all accessories as required for Fan Points.( Length of the points will be 5 to 8 mts.)

Wiring, Connecting, Testing & Commissioning with 3 X 1.5sqmm PVC insulated single core unsheathed copper conductor cable of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceilling with PVC accessories, including supply and fixing of modular 2 nos of 6A two way switch, one step type fan regulator along with moulded front plate in G.I anodised manufacturer’s mounting box fixed flush with the wall complete with all accessories as required for Fan Points.( Length of the points will be 5 to 8 mts.) two way fan point

Wiring, Connecting, Testing & Commissioning with 3 X 1.5sqmm PVC insulated single core unsheathed copper conductor cable of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceilling with PVC accessories, including supply and fixing of modular 6A switch, and 5 pin socket. Push along with moulded in front of G.I anodised manufacturer’s mounting box fixed flush with the wall complete with all accessories as required for light Points. Length of the points will be 5 to 8 mts.)

Sockets : Supply and fixing of 6A 3pin and 2pin combined modular type switch concealed in manufacturer's G.I. mounting box in flush with wall .

Supply and fixing of 3x 6A 3pin and 2pin combined modular type switch concealed in manufacturer's GI mounting box in flush with wall earth connections (for computer plug socket)

Supply and fixing of 5A/15A 3 pin combined flush type wall socket with 15A flush type switch concealed in suitable MS box in flush with wall with painting

Supply and fixing of 25A 3 pin and 2 pin combined Flush type Wall Socket with 25A DP MCB complete set for AC unit in switch along with moulded front plate in G.I anodised manufacturer's mounting box fixed flush with the wall complete with all accessories as required as per the site condition.

Supply and fixing of Flush type of 25A DP Modular type swirth with indicator concealed in swithch with moulded front plate in G.I anodised manufacturer's mounting box fixed flush with the wall complete with all accessories as required as per the site condition.

EMTY PVC CONDUIT Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

20mm dia

25mm dia

32mm dia

FITTINGS

Supply and Fixing of single box type 4 feet 36-W Flu Fitting complete with Electronic ballast with TW round Blocks on wall or ceiling with flu tube with PVC unsheathed copper leads from terminal to the fitting

Supply and Fixing of round type splot light 10W cool with 5700K - 6500K LED efficasy >100 lumes / Watts with in built driver in input voltage range 140-240V AC PF>0.90, body extruded aluminium with poly corbonate milky diffuser suitable wall / surface mounting

Supply and Fixing of Round type spot light 18W LED surface mount LED lights body made of CRCA powder coated body fitted with LED back lite panel light body made of di cast aluminium Milky poly carbonate diffuser,Long-life electrical driver to deliver optimal performance. working voltage window 145-265 V AC 50 Hz and maintain PF > 0.9 and Surge up to 2.5 kV High efficiency led with efficacy 120 Lumens/watt Cool white - 3000 K to 6500 K with CRI > 0.8 (Make : Philips / Crompton /wipro/ elenserve )

Supply and fixing of 1200 mm (48") AC ceiling fan complete with out regulator and 1000mm down rod including fan clamp with side plates and cross arm of size 450mm (18")

Supply and fixing of 300 mm sweep Wall Mounted Fan Circulator complete and including fan clamp with Necessary required Job etc...

Supply and fixing of 300 mm (12") sweep (Light duty) AC Exhaust fan complete without provision of hole in the wall.-

Supply and laying of 3.5x70Sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75m putting 0.15m of sand and covering cable completely with bricks and sand refilling to make good.

Fabricating , supply, erection, testing and commissioning of CPRI certified indoor panel board made up of 2mm thick powder coated CRCA steel sheet with Cu bus- bar provision (Ph 25x10mm for all phases Ne- 25x10mm &E-2x25x3mm)with heat shrinkable insulation and SMC supports, door with Industrial lock, Incomer 200A TPN MCCB, 1Set metering compartment consisting of 1 no Digital multi functional metre accuracy class 1.no with 3 nos of CT s 200/5 Amps ratio and RYB cluster type indication lamps with control fuses with provision for locking the indoor panel board complete etc. as per IS standard . The above panel board is to be erected with anchor fasteners, bolt and nuts with suitable angles and channels of size 75x40mm (drawing to be approved by the Engineer in charge before fabrication)

Supply and fixing of 30 W LED street light fitting with 19mmdia GI pipe ( class B ) with 1 no of 19mm dia GI bend completed on existing post & wall with MS plate with PVC unsheathed cu leads with clamp and aluminium painting with LED lamp. (Make : Philips/ Crompton/ wipro/ elenserve or equivalent)

Plate earthing with copper plate of size 600 x 600 x 3 mm as per the ISI specification with an earth electrode of 2.1 mtr class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm with necessary funnelling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supplying and fixing of 5 HP/ 40 stage delivery Submersible motor ISI make for 6"dia borewell with and Conforming to IS 8034/89 with ISI marking as per standard Specification. The Trail run for 3 days Continuously by the Contractor at his own Cost.(The pump set Should be got approved by the Estate officer Before Erection) 1. Discharge:50/LPM 2. Total Head : 175/metre The pump Set Shouls be got approved before erection of pump set.

SMART PROCON PRIVATE LIMITED (BID ID -1330181)

P SANKAR (BID ID -1333548)