UPGRADATION/IMPROVEMENT OF CERTAIN SMQs AT AIR FORCE STATION UTARLAI

Demolition of un-reinforced cement concrete in floors or pavings n. exc. 15 cm thick (below or above ground level) complete all as specified and directed by Engr-in-charge.

M&L for 25mm thick PCC 1:2:4 type B-1(using 20mm graded aggr) as in level course finished even and rough with out using extra cemet.complete all as specified and directed by Engr-in-charge.

S&F Coloured Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM(1:6)complete all as specified and directed by Engr-in-charge.

S&F Coloured Non Skid ceramic tiles 7 to 8mm thick joint less (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM(1:6) with providing of any dark colour border complete all as specified and directed by Engr-in-charge.

All as per Item No 4 above but as in skirting including 10 mm thick rendering in CM 1:4complete all as specified and directed by Engr-in-charge.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and directed by Engr-in-charge.

M&L for 18-20mm thick granite (of any type) work, table rubbed mirror and polished as in steps, jambs, pillars, window- cills, cooking platforms and like bedded over and including 20mm thick screed bed in CM (1:4) and pointing in white cement (1:2) using marble dust with admisture of pigment to match with shade of granite complete all as specified and directed by Engr-in-charge.

M&L for pre-polished machine cut Kota stone as in stair case tread, riser & skriting 20-25mm thick laid over 20mm thick screed bed in CM (1:6) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, bull noseing etc complete all as specified and directed by Engr-in-charge. Note : Single stone piece on one tread with nosing one side shall be provided.

M&L for mirror polished machine cut kota stone as in slab flooring 20-25 mm thick single piece of each fread over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing over and including 20 mm thick screed bed in cement mortar (1:6) complete all as specified and directed by Engr-in-charge.

M&L for cutting holes in stone walls or any type of wall (Circular or square) any size exc half stone but not exc one stone thick, built in cement mortar or in cement lime mortar for exust fan ventilation or similar work and making good of dismantled portion in c.m 1:3 or cement concrete 1:2:4. complete all as specified and directed by Engr-in-charge.

Demolition of cement concrete reinforced of any descrition and in any position not otherwise specifially provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed by Engr-in-charge.

M&L for form work to soffits of suspended slabs such as roof slabs,cooking platform, floor slabs, landings and similar work, flat rought finished surface of concrete to RCC work , complete all as specified and directed by Engr-in-charge.

M&L for RCC nominal mix type B-1, 1:2:4 (20mm graded aggregate) for slabs supported on walls , beams and columns in floors, roofs, landings, balconies, conopies, deck slab and in shelve and the like. complete all as specified and directed by Engr-in-charge.

S&F of precast cement concrete type B1 1:2:4 (20mm graded aggregate, with reinforced as required) as in baluster, apex stones, pier caps, columns , posts of balcony and similar work set in cement mortar 1:4 and finish smooth with using putty and two coats of weather. complete all as specified and directed by Engr-in-charge.

M&L TMT bars 10 mm dia and over , cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm diameter including all necessary scaffolding, including drilling work for inserting TMT bar in wall including filling of epoxy ,machinery,tools tackels and men materials complete all as specified and as directed by Engr-in-charge. (Note : The work shall be carried out upto 12.0M height)

Dismantaling floor hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

M&L for coloured glazed ceramic tiles size 300 X 450 X 7-8mm thick on vertical surface over 10mm thick rendering in CM (1:4) as in dado/skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match with coloured complete all as specified and directed by Engr-in-charge.

Demolition of un-reinforced cement concrete of any description and in any position not otherwise specifieally provided complete all as specified and directed by Engr-in-charge.

M&L for PCC 1:5:10 (Brick coarse aggregate) filling as in sunken floor / sub base of flooring and similar work including demolition of existing sunkun floor and similar work. Complete all as specified and directed.

M&L rendering 15mm thick in CM 1:3 on brick work or concrete surfaces, mixed with integral water proofing compound as per manufactures instructions, finished the surface even and smooth without using extra cement and applying evenly a tack coat of blown bitumen 85/25 @ 1.2 Kg/Sqm over a coat of water based bitumen emulsion primer at the rate of 0.30 ltr/Sqm including cleaning the surfaces thoroughly from dust and dirt and lay water proofing treatment with felt having glass fiber non woven reinforcement and weighing 3.0 Kgs/Sqm to 4.0 Kgs/Sqm in 100mm overlaps both longitudinally and transversely by torch bonding and applying a coat of blown bitumen 85/25 @ 1.2 Kgs/Sqm on top of felt on surface (bottom and vertical) as in sunken floor and similar work. complete all as specified and directed by Engr-in-charge. (Note : Supply of water proofing compound will be measured and paid separately .)

S&F in repair High density polyethylene pipe (HDPE) 40mm bore of pressure rating 6kg/cm2 fixed to wall, ceiling or laid in floor etc complete all as specified and directed.

Supply only integral water proofing compound.

M&L for PCC 1:1.5:3 Nominal mix concrete type A1 ( Using 20mm graded aggregate) as in lavel course on roof, roof flooring, mass concrete and similar work, finish even and smooth without using extra cement. complete all as specified and directed.

M & L for 10 mm thick screed bed in cement mortar 1:4 complete mixed with water proofing compound as per manufacturer instructions over roof top surface finished even and smooth using extra cement and application of water proofing treatment using APP modified roof membrane over existing accessible RCC roof slab / chajja / canopy / parapet wall to be executed through approved applicator of the membrane manufacturer with following specification etc complete all as specified and directed :- (a) Cleaning existing surface properly. (b) Applying bitumen primer/tack coat of in dustrial bitumen 85/25 at the rate of 1.20kg/Sqm by the same agency as that of APP membrane. (c) Laying of APP based polymeric membrane minium weight 3kg/Sqm and miniume 3mm thick reinforced with polyster non wove fabric (Wt not less than 150 gms/sqm) land on primed surface by forced application using butane torch by torch application with 100mm side laps and 150mm end lap. (Note:- WPC shall be measured and paid separately)

M&L for 75mm thick cement concrete (1:3:6) type C2 using 20mm graded stone aggregate as in paving/plinth protection in bitumen filler/mastic filling Complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster of any description on bricks, concrete or stone walls etc. including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L, rendering 15mm thick on concrete surface or brick/stone work in CM 1:4 finished even and smooth with out using extra cement similar work up to G+1 height of the bldg. all as specified and directed.

M&L for rendering 10mm thick in CM (1:6) on walls, finishing even and smooth without using extra cement similar work .complete all as specified and directed by Engr-in-charge.

M&L for rendering 5mm thick in CM (1:4) on concrete surface such as roof projection, chajja, fin & ceiling and similar work up to G+1 height of the bldg, finishing even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M&L for preparation of surface and applying two coats of oil bound distemper on newly plastered wall surfaces over one coat primer and over and including 1.50 mm thick wall care putty complete all as specified and directed by Engr-in-charge.

M & L for prepration of newly plastered external surfaces of wall and for applying two or more coats of Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) all as per manufacturs instructions incl necessary scaffolding writing letters etc complete all as specified and directed by Engr-in-charge.

Prepration on new plastered or unplastered ceiling surface and applying Three coat of white wash up to G+1 height of the bldg. complete all as specified & directed by Engineer-in-Charge

Taking down frames with shutters (without taking off shutters from the frame ) area not exc 1.5 Sqm Each incl iron mangery complete.

S&F, Powder coated(powder coating not less than min 50 Micron)aluminium frame for doors,windows, partition, ventilators with one or more rebates including joining cleat for fixing/sliding etc. Complete all as specified and directed by Engineer-in-Charge.

S&F Powder coated(powder coating not less than min 50 Micron) aluminium rolling/side hung window and ventilator shutters without sash bars, aluminium sections weighting 0.55 Kg/Mtr incl necessary joining leats, glazing lcip, subber packing, snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1Nos) hinges type B-21 100mm long(02 Nos suitable powder coated handle as required Powder coated aluminum snap beading screws etc . Complete all as specified and directed by Engineer-in-Charge.

S&F for framed work such as grills gratings etc with ends of bars shoudered and /or riveted, or forged into spikes, framed guard bars barred iron doors ladders framed blaluster walk way railings framework of waterr tands and similar works conforming to Fe 290 Gde E-165 complete all as specified and directed by Engr-in-charge.

M&L for preparation of new or untreated steel surfaces of any description over 10cm width or girth not otherwise described and applying two coat of synthetic enamel paint over one coat of primer , complete all as specified and directed.

M&L ,sheet glass ordinary quality 4.8/5 mm thick(tinted/plain) and glazing with oil putty or aluminium clip and similar work in squares exc 0.5 sqm each pane fixed.

S&F, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm. complete all as specified and directed.

Supply and fixing,Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

Providing and fixing, factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

S&F,Butt hinges, 100 mm size extruded aluminium alloy with galvanised mild steel hinge pin, anodised .

S& F, 200 mm long, aluminum anodised barrel tower bolts of extruded section complete as specified.

S&F, 150mm long aluminum alloy handles fabricated type, anodized complete as specified.

Taking down frames with shutters (without taking off shutters from the frame ) area exc 1.5 Sqm but n.exc 4 sqm mtr Each incl iron mangery complete.

S&F ,105 x 60mm pressed steel frames for doors with one or more rebate including necessary fixing lugs, hinges lock strike plate etc complete as specified including a coat of shop coat zinc chrome primer complete all as specified.

S&F, 125 x 60mm pressed steel frames for doors with one or more rebate including necessary fixing lugs, hinges lock strike plate etc complete as specified including a coat of shop coat zinc chrome primer complete all as specified.

S&F, factory made flush shutters 35 mm thick, solid core construction with block board core and plywood face panels, commercial type, both side of shutterr covered with decorative type veneer in factory made/pressed with lipping/framed to match. complete all as specified & directedand designe as approved by Engineer-in-Charge.

S&F, 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) , edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing gauze etc, sizes of members of shutters as specified in SSR Part I. (2nd class hard wood). complete all as specified & directed by Engineer-in-Charge

S&F, 100mm butt hinges, medium weight, cold rolled mild steel and fixed.

S&F, 300mm length aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts and sliding bolts of extruded sections or cast-aluminium alloy. complete all as specified and directed.

S&F, floor door stoper (140mm length) of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed to door complete. complete all as specified and directed.

S&F, 300 mm ordinary MS rat rail rod pattern spring including roller and roller plate complete

M&L for preparation of new or untreated wooden surfaces of any description over 10cm width or girth not otherwise described and applying two coat of synthetic enamel paint over one coat of primer and over one coat of wood putty, complete all as specified and directed.

S&F Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Board(any coloured) of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm an ISO 9001 - 2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng butt hinges with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer-In-Charge,

S&F,100mm long aluminum alloy handles fabricated type, anodized complete as specified.

S&F, magnetic wardrobe ball catcher suitable for shutters fixed with nut,screw and washers of mild steel,bright finished.

S&F, 75mm butt hinges, medium weight, cold rolled mild steel and fixed.

S&F Sliding Rail/channel for drawer 450mm long suitable for kitchen tray and similar workcomplete all as specified and directed.

S&F in repair Rotational moulded 3 layers polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position incl all fitting such as tank nipple/GI fitting incl PTMT float/ball valves 20 mm dia high pressure with epoxy coated aluminium rod and high denscity plastic ball screwed for iron pipes (Min weight 210 gms)and fixed to iron pipes etc. all as specified in SSR Part I for 500 ltrs capacity incl dismantling of old tank.complete all as specified and directed by Engr-in-charge.

Dismantling of cast iron or reinforced concrete drain pipes/PVC pipe 100/75mm dia and under any type, jointed in cement mortar and taking out of trenches if required .

S&F, CI soil waste vent and rain water pipe 75 mm bore (ISI Marked) in any length with or without ears with cement joint laid in floor/fixed to wall complete all as specified and directed. Make:- Nico or equivalent make approved by GE.

S&F, CI soil waste vent and rain water pipe 100 mm bore (ISI Marked) in any length with or without ears with cement joint laid in floor/fixed to wall complete all as specified and directed. Make:- Nico or equivalent make approved by GE.

S&F in repair cast iron floor trap 75 mm outlet dia with grating including jointing to waste pipe fixed in cement concrete type B1, (1:2:4) complete all as specified and directed.

S&F, 100mm bore branch piece single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches.

S&F, 75mm bore branch piece single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches.

S&F ,100mm bore bend (any radius) with duck foot or heel rest.

S&F, 75mm bore bend (any radius) with duck foot or heel rest.

M&L for 15 mm bore GI tubing, medium grade with all fittings and fixed complete to walls with clamps, ceiling, floors or laid in trenches, concealed to wall/open to wall incl taking down old pipe. complete all as specified and directed by Engr-in-charge.

M&L for 20 mm bore GI tubing, medium grade with all fittings and fixed complete to walls with clamps, ceiling, floors or laid in trenches with concealed to wall/open to wall incl taking down old pipe. complete all as specified and directed by Engr-in-charge.

M&L for 25 mm bore GI tubing, medium grade with all fittings and fixed complete to walls with clamps, ceiling, floors or laid in trenches incl taking down old pipe.complete all as specified and directed by Engr-in-charge.

S&F in repairs 20 mm bore Gun metal, globe, gate valves/Ball valve high pressure with polythene float and fly nut complete screwed for iron pipe or for unions. complete all as specified and directed by Engr-in-charge.

S&F in repair stainles steel sink with drainage board made out of stainless steel 1.00mm thick sheet for kitchen with plugs, washers and waste, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting unions to pipe over all size 915mmx460mm with bowl size 410mmx330mmx160mm incl waste pipe etc complete all as specified and directed by Engr-in-charge.

S&F in repairs vitreous china squatting pan , "Orissa" pattern size 580 x 440 mm white, with integral foot rests (excluding flushing cistern, flush pipe and waste pipe).complete all as specified and directed. complete all as specified and directed by Engr-in-charge.

S&F in repairs vitreous china wash hand basin, angle back, size 550x400mm white excluding taps, waste, chain and plug and porcelain stopper including brackets, complete all as specified and directed.complete all as specified and directed by Engr-in-charge.

S&F in repair 600mm X 450mm (5 mm thick) looking mirror decorative type beading of any size of standard quality bevelled edge mounted on 6 mm thick ply wood and fixed with rubber plugs, screws, cup washers, complete all as specified and directed.

S&F, PVC low level fushing cistern 10 liters capacity including 32mm dia PVC down pipe,brackets etc complete all as specified and directed by Engineer-in-Charge.

S&F in repair chromium plated long body pillar tap 15 mm dia cast copper alloy with capstan head , screwed down high presure with or with out lettered fixed with iron pipe, complete all as specified and directed by Engr-in-charge.

S & F in repair angle/stop valves cast copper alloy chromium plated with long shank , screwed both ends for iron pipe 15mm bore, complete all as specified and directed by Engr-in-charge.

S&F in repair Chromium Plated wall mixer for mixing Hot & cold water screwed down for iron pipe 15mm bore complete all as specified and directed by Engr-in-charge.

S & F in repair bib taps (long body) cast copper alloy with crutch or butter fly handle screwed for iron pipe of dia 15mm fixed, complete all as specified and directed by Engr-in-charge.

S&F in repair Chromium Plated kitchen sink mixer for mixing Hot & cold water screwed down for iron pipe 15mm bore complete all as specified and directed by Engr-in-charge.

S&F in repair brass chromium plated shower rose with swivel joint 125mm size in square with CP long shank arm including fixing to steel pipe or union complete all as specified and as directed.

S&F of stainless steel wall hook for hanging cloth and towel hangers for 6 no of hook set fabricated on stainless steel flat plate as per sample approved by Engineer-in-Charge.

S&F in repair Chromium plated Towel rail with towel racks of 600mm long of fixed with & including CP brass screws & wooden/plastic cleats (min. weight 190 gms) complete all as specified and directed by Engr-in-charge.

S&F in repairs stainless steel 1mm thick kitchen plate rack , size 30"x30"x10" , fixed with galvanised screws. complete all as directed by Engr-In-Charge.

S & F, glass shelf assembly consisting of 5.5mm thick glass shelf 150mm wide & 600mm long with chromium plated bracket guard incl Stainless steel 100mm long bracket (one Pair).complete all as specified and directed by Engr-in-charge.

S&F in repair 32/40 mm CP waste coupling (half or full threaded) (Min weight 45 to 60 gms) all as specified and directed.

S&F in repairs 32/40 mm dia PVC waste pipe for sink and wash hand basin of pressure rating 10 kgf/Sqm complete all as specified and as directed.

S&F in repairs PVC connection 15mm dia and 600mm long with two Nos of PTMT checknuts and washers complete. All as directed by Engr-in-charge.

Complete removal of existing treatment of wall surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and effloescent salts and trading oil and greasy spots and applying two coats of oil bound distemper over and included 1.50 mm thick wall care putty to make smooth surface incl complete removal of existing treatment on walls all as specified and directed by Engr-in- charge

Complete removal of existing treatment of wall surface external surfaces including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and effloescent salts and trading oil and greasy spots and for applying two or more coats of Finishing walls with Acrylic Smooth exterior paint of required shade (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) all as per manufacturs instructions incl necessary scaffolding writing letters etc complete all as specified and directed by Engr-in-charge.

M&L complete removal of existing treatment of wall surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and effloescent salts and trading oil and greasy spots and applying two coat of white wash up to G+1 height of the bldg . complete all as specified and directed by Engr-in-charge.

M&L, preparation of old surface of Ceiling including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and effloescent salts and trading oil and greasy spots and applying one coat of white wash up to G+1 height of the bldg . complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and directed by Engr-in-charge.

M&L for preparation of old painted wooden surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and directed by Engr-in-charge.

Taking down cement plaster or Chipping out of plaster from ceiling of slab/columns/beams/chajjas/parapet/roof projection/balcony/staircase and removing loose mortar with chisel hammer without much impact on concrete surface complete all as specified and directed by Engr-in-charge (Note : The work shall be carried out upto 9.0 M height)

M & L for clean the surface by cleaning the exposed reinforcement with wire brush & appliying Reebaklens RR rust rust remover or equivalent in two coats over only rusted reinforcement surface and providing anti corrosive coating with two component epoxt based zinc rich primer/Rust passivation Inhibitor coat at the with primer or equivalent only over reinforcement surface as per manufacturers instructions and applying bond coat on the prepared old surface of concrete/masonry to receive new polymer mortar/polymer modified martar / micro concrete in two coats as per maufacturer instraction and specifications. (Note : work shall be carried out upto 9.00M height and through approved company authorised applicator) The rate inclusive of all materials, labors, supervision, tools, transportation, scaffoldig arregement etc.,

M & L for perparation the surface and applying 10 to 40 mm thick in layers , each layer n.exc 20mm thick with polymer modifed mortar (PMM) on sufcace of slab/columns/beams/chajjas/ parapet /roof projection/balcony/staircase with Renderoc SP40 chemicals including all necessary scaffolding, man and material complete all as specified and directed by Engineer-In-Charge. (Note : work shall be carried out upto 9.00M height and through approved company authorised applicator)

S&F for GI wire netting (Murga jali) 0.90 mm dia and 12mm mesh lathing to wood or matal sudding, joists etc in wall, ceilings, stanchions, beams etc including all laps cutting and waste complete all as specified and directed by Engineer-In-Charge. (Note : The work shall be carried out upto 9.0 M height)

M & L for 15mm thick cement plaster CM 1:4 with added intigral waterproofing compound and prepration of newly plastered surfaces of and for applying two or more coats of Finishing walls/ceiling with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) all as per manufacturs instructions incl necessary scaffolding writing letters etc. complete all as specified and directed by engr-in-charge. Note : The work shall be carried out upto 9.0 M height.

Demolition of reinforced cement concrete in roof slab/chajjas / beams / cantilever/ balcony/ staircase etc and other suspended work of any description complete all as specifed and directed by engineer-In-Charge. (Note : The work shall be carried out upto 12.0M height)

M&L TMT bars 6mm to 8mm dia bar , cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm diameter including all necessary scaffolding, including drilling work for inserting TMT bar in wall including filling of epoxy ,machinery,tools tackels and men materials complete all as specified and as directed by Engr-in-charge. (Note : The work shall be carried out upto 9.0M height and no any extra payment shall be paid for scaffolding and man power on this account)

M&L for providing leak proof shuttering to RCC member such as roof slabs, roof projection, and similar work in any position cut to length and providing including runners supports including including all necessary scaffolding ,machinery,tools tackels and men materials complete all as specified and as directed by Engr-in-charge. Note: The work shall be carried out upto 9.00 M height .

M&L for providing Micro concrete at the rate of 25kg per 0.0125 m3 with 20% properly graded 5mm to 10mm silt free aggregate as per manufacturer instructions and mixing concrete with mechanically electrically operated mixer machine etc complete all as specified and directed by Engr-in-charge.. (Note : The work shall be carried out through approved company authorised applicator and upto 9.0M height)

S&F for framed brackets of angles or tees with web and flanges cut to shape for cooler stand and simiar work, drilled and countersunk for screw, including beding and welding angles as neceesry gusset plates riveting etc oncforming to Fe 290 Gde E-165 complete all as specified and directed by Engr-in-charge.

M&L for PCC (1:1.5:3) type B-1 using 20 mm graded stone aggregate as in hold fast, coping and similar work including necessary form work, complete all as specified and directed.

Excavating in trenches in any type of soil, n.exc. 1.5m wide and n.exc. 1.5 m in depth, for foundation, etc. or for shafts, wells, cess pits, manholes, pier holes, etc n.exc. 10 sqm on plan and n.exc 1.5m in depth and getting out.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25cm.

Removing excavated material (soil) n.exc. 50 m and depositing where directed at a level n.exc. 1.5 m above the starting point.

Demolition and breaking up drain pipes, (Salt glazed stoneware, AC or reinforced concrete) upto & incl 150mm (internal dia) set in cement mortar.

M&L for cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in bed to drain pipes of size 150 mm bore, including packing under & haunching against the sides of pipes after they are laid and tested.

M&L for DWC sewage pipe (Double wall corrugated) with collars for 150 mm internal dia, ISI marked laid to slope in trenches for sewage work. complete all as specified and as directed.

Demolition of PCC block or stone masonry, built in cement mortar, complete all as specified and directed.complete all as specified and directed by Engr-in-charge.

Taking down cement plaster of any description on bricks, concrete or stone walls etc. including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for precast cement concrete block masonry with solid blocks of PCC 1:3:6 type C1 using 20 mm graded stone aggregate, exc. 10 cm in width and setting in CM 1:6 complete .complete all as specified and directed by Engr-in-charge.

M&L , rendering 15mm thick on concrete surface or PCC block masonry /stone work in CM 1:4 finished even and smooth with out using extra cement similar work .All as specified and directed.

S&F in repair PVC (SWR) gully trap 125/110 mm,setting and jointing with solvent cement all as directed.

M&L for cutting into existing manholes for connecting new drains of 150mm internal dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel ( ½ round or 3/4 Section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required.

Demolition of reinforced cement Concrete of any description and in any position not otherwise specifically provided for

M&L for precast reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate in landings, cover slabs (for manholes/septic tank/soak well etc.) chullah hoods, chajjas, shelves and similar articles with plain faces, set in CM 1:4, including necessary form work moulds etc all as specified. (Reinforcement shall be measured and paid for separately).

M&L for mild steel TMT bars 6 mm to 8 mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia.

Taking down copper/Aluminum point wiring (light,fan,bell,socket or power) complete including fixture and fittings such as switches, ceiling roses, pendent,regulators,sockets,light fitting etc.Removing materials to store for keeping in safe custody or for taking credit ( credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc complete all as specified and directed at site.

Taking down old/unserviceable distribution board by disconnection of electric connection carafully SPN DBs/TPN DBs/Main Switch including old unserviceable MCCBs/MCBs, Isolators, etc and making good to disturbed surface complete all as specified and directed.

Taking down carefully copper/aluminium Sub main wiring of any size from surface/concealed/ existing conduit of any height and removing materias at site and making good disturbed surface of walls, floors roofs etc complete all as specified and directed.

Taking down, disconnecting the power supply carefully existing energy meter by carefully opening electric connection from terminal and depositing to MES store for safe custody, the final reading from the meters shall informed to MES authority for final settlement complete all as specified and directed.

Taking down existing ceiling fan/exhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan abd fan blades and deposit to MES store yard of AGE E/M for safe custody complete all as specified and as directed.

M&L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit heavy duty ISI marked of white/ivory colour including all accessories heavy duty ISI marked after chasing in wall/ceiling etc, with GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.5 sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed for the following:-

One light point controlled by one, one way switch 5 Amps

One fan / exhaust fan point controlled by one way switch 5 Amps and regulator

One light point controlled by one, two way switch 5 Amps

One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board

One 3 point 5 Amps switch socket outlet point controlled by one switch on independent board

One bell point controlled by one, bell switch 5 Amps

Description all as per item no- 129 here in before but using 2.5 sqmm single core copper condutor FRLSH cable of multistranded PVC insulated unsheathed 1100 volts grade for 5/15 Amps switch socket combination point including necessary running of 2.5 sqmm copper conductor FRLSH cable of multistranded PVC insulated unsheathed as earth continuity conductor along with wiring and connecting to the common earth dolly.

Description all as per item no-129 here in before but using 4.0 sqmm single core copper condutor FRLSH cable of multistranded PVC insulated unsheathed 1100 volts grade for 5/15 Amps switch socket combination point including necessary running of 4.0 sq mm copper conductor FRLSH cable of multistranded PVC insulated unsheathed as earth continuity conductor along with wiring and connecting to the common earth dolly.

S&F for modular switch piano flush type, single pole, one way and 5/6 Amp single module complete all as specified.

S&F for modular switch piano flush type, single pole, one way and 15/16 Amp single module complete all as specified.

S&F for modular switch flush type, single pole, two way and 5/6 Amp single module complete all as specified.

S&F for modular socket outlet multipurpose (suitable round and flat pin) having provision for 3 pin, 5/6 Amp 2 module piano flush type complete all as specified.

S&F for modular socket outlet multipurpose (suitable round and flat pin) having provision for 3 pin, 15/16 Amp and 3 PIN,5/6 Amp, 2 module piano flush type complete all as specified.

S&F for modular step type fan regulator120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed.

S&F for Bell push modular 6 amps sibgle module complete all as specified.

S&F for lamp holder, PVC / Polycarbonate type with back plate suitable for batten/ slanting fittings complete all as specified and directed.

S&F for Bell electric Ding dong type suitable for operation on 230 volts, 50 HZ AC supply complete all as specified & as directed.

S&F for modular type TV socket outlet complete all as specified and as directed.

S&F for modular type three pin socket 3 pin 16/20 Amps with plug op On/Off switch suitable for 230 volt 50 Hz AC supply complete all as specified and as directed.

M&L for sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 2.5 sq mm nominal area and drawing into suitable size of PVC non metalic rigid heavy duty PVC conduit of white/ivory colour and its accessaries ISI marked heavy duty of suitable size includingconcealed in wall etc one run of PVC insulated with 2.5sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Two runs of 2.5 sqmm cable , one run of 2.5 sqmm cable and one run of PVC conduit will be measured as one unit.

S&F for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnatic locking system including necessary provision fr inserting the DBs in wall by cutting the brick/stone masonary etc and making good of disturbed surfaceto match with existing colour of wall complete all as specified and as directed.

S&F for MCB single pole and neutral rated capacity 32 Amps, 240 volts breaking capacity 10 KA 'C' curve complete all as specified and as directed.

S&F for MCB single pole rated capacity 5 to 32 Amps, 240 volts breaking capacity 10 KA 'C' curve complete all as specified and as directed.

S&F for Water Heater storage type (Geyser) vertical/horizontal type as per site requirement with inner container of capacity 25 ltrs, Electracally operated AC 230 Volts BEE 5 Star rated ISI marked including 4 Nos of hold fashner nuts required suitable size fixed in bric wall, all necessary electrical and water supply connections with PVC connection pipe hot & cold complete all as specified and as directed.

S&F ceiling fan, 230 Volts, 1200 mm sweep with main air dilivery 245 CFM, 28 Watt, service value of the fan shall be greter than 6.1 (5 Star rated) as per BIS with blades, down rod and other necessary accessories with brushless direct current motor (BLDC) without remote system and lectrical connections from ceilling rose to fan terminal complete all as specified & directed.

S&F for energy efficient Exhaust fan of 300mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washer size of the bolt 15 mm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base complete all as specified and as directed.

S&F for energy efficient Fresh Air fan of 225mm sweep made of PVC body Ventil Air -DS type complete with louver with bolts nuts and washer size of the bolt 15 mm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base complete all as specified and as directed. Note for item no-149 & 150: Cost of suitable opening wall for fixing exhaust fan is deemedto be included in overall rate quoted.

S & F for Highly efficient LED Bulbs, 10 W inverter type complete all as specified and directed.

S&F, Light light fitting 4' long, 20/18 Watt single phase 230 V with illumination efficiency more than 120 Lumen/Watt, 3000K/6000K, decorative tuneable white browse through three mood changing colour options type slim ultra bright LED polycarbonate tube fixture with extruded heat shrink, environmental friendly energy efficientwith very high efficiency to give glare free light at light source incl integrated electronic driver complete all as specified and as directed.

S&F for Decorative wall mounted Luminaire madeout of Nickle finesh square base with bend pipe with unbreakable globe glass suitable for LED bulb and provision of LED bulb 10 watts complete all as specified and as directed.

S&F for LED light fitting 2 feet 10 watts mirror type with high out put diffuser, decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to fitting complete all as specified and as directed.

S&F for LED light fitting 2 feet 05 watts mirror type with high out put diffuser, decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to fitting complete all as specified and as directed.

S&F for Energy saving new generation 10 watts Bulk head fitting IP 65 Luminaire with opel diffuser pre wired with warranty option of 5 years from date of installation and necessary mounting arrangements provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiliong rose to fitting including LED bulb complete all as specified and as directed.

S&F for Energy saving new generation environmental friendly long life versalite pressure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25 watts with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded fromceilinf rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shapewith clamps, nut,bolt complete all as directed.

S&F for PVC non-metalic rigid conduit ISI marked heavy duty white/lovry colour and its accessories heavy duty ISI marked of size 25 mm dia for LAN, telephone and TV connections including cutting chasses and making good disturbed surface oto match with existing finish with plaster complete all as specified and directed.

Supply, installation, commissioning and testing indoor type LT wall mounting bldg panel board of suitable size factory made TTA panel, weather, dust and verming proof indoor, double door, front openable, locking arrangment made out of 2.00 mm thick mild steel CRCA sheet including required compartment for fixing of (04) Nos of single phase smart meter, 01 Nos of single phase smart meter (stair case), MCCB and MCB and providing glass view for reading of meter reading and providing rubber / PVC gasket of suitable size all side of door with copper bus bar wrapped with PVC tape / sleeves with maintained the color code and copper strip / wire busbar of suitable size to MCCB input and MCCB / MCB outpur of suitable length for connection of cable from main busbar, angle iron 50 mm x 50 mmx 5 mm thick supporting frame including applying to coats of powder coated paint over a coat of red oxide zink chrome prime over exposed external and internal surfaces for three phase 4 wire system 145 / 440 Volts grade including internal wiring connections for all outgoing / incoming cable, earthing turminals, danger plate, suitable PCC platform complet all as directed by Engr-in-Charge

Supply and Installation of Smart Single Phase Meter of different makes (Not more than 33 % of a particular make) including polycarbonate boxes with transparent cover to view meter display with the following specifications:

(a) AC Single Phase Two Wire, Tamper Proof, Static Meter of Class 1.0, 240 V, 50 Hz, 5A-60A, with 3200 impulses per KWh,LED for Phase presence & LED for Relay status, conforming to IS-16444 standard with inbuilt 865-867 MHz 6 Low PAN Mesh Radio Frequency communication facility with self healing Mesh network with default and on demand display, billing data generation facility, anti-tamper features, Microprocessor and LCD based display only with compatible IP54 compliant polycarbonate box for outdoor mounting with optical port Provision on meter box.

Meter Should support the following data : 15/30 min instantaneous data for Voltage, Current, Power factor, Power, Cumulative energy and frequency, monthly billing data & antitamper features. Load survey data for 45 days with 30 min integration period for kWh, Voltage, Current, frequency etc.

Meter should have connect / disconnect functionality operable from prepaid billing software & shall show balance on display

The meter should support open communication protocol DLMS with the software

Note :- (a) The contractor should be responsible from removing the existing meter, noting down the reading and depositing it with the MES.

(b) It should run the meter in both prepaid and postpaid mode

(c) The meters should carry 5 year warranty.

(d) OEM shall have own NABL accredited lab for testing meters as per IS 16444 and certification shall be provided during sample approval

(e) The meter cost would include DCU/ Gateway and repeater cost for RF commuication meters

Supplying, Fixing, Commissioning and testing of configuration of cloud based prepaid software for with following modules:

(i) Meter Data Management Module: The meter data management module would be responsible for collecting the data from the data concentrator and make the data available to the billing system. The system would support offline meter data entry. The meter data management system would capture and provide the following data:

(a) 30min instantaneous data from all the meters for seven parameters- Cumulative Energy,Power, Current, Voltage, Power factor and Frequency.

b) Monthly and quarterly billing survey data for cumulative energy and max demand, Load Survey Data, Tamper Events

(ii) Communication module: The system should provide communication of energy data and bills via print, email.

(iii) Meter Master Data : The system would support meter data repository. The system should support meter replacment process.

(iv) Excel Export : The system would support export of metering and billing data in excel format

Note:- (i). Software will be compatible with all makes of smart meter & shall be CERT-IN certified from CERT approved vendors for any cyber security related threat & complying as per ENC guidelines.

(iii)The software would be hosted on MEITY GCC approved server 2 years hostingcosts would be included.

M & L for maintenance free chemical earthing of technology with copper bonded steel rod 3 mtr long 25.0 mm dia with 250 micron copper bonded coating and UL listed. There should be turminal for connection of 150 x 50 x 6 mm with 4 holes of 12 mm dia alongwith 2 bags of 25 kgs each of earth enhancing compound. The chemical compound should be tested and certified by any NABL accredited laboratory with 95% carbon containt. The testing laboratory should be an ISO 9001 & 14001 certified. The earthing inhancing compound should be IEC 62321. The ph value of compound should be 7-8. Electode should be duly tested and certified by CPRI, Govt of India for a minimus short circuit current of 25 KA RMS for 1 second. Including necessory boaring of suitable dia upto required depth in any type of soil for insurting copper rod and filling of chemicals and poly plastic pit cover of material polymer body and cover diamention -308 mm(L) x 308 mm(W) x 214 mm(H) bearing capacity 7.5 ton approved from NABL approved lab complete all as specified and directed. Note:- (i) Earthing is to be done infront of the Engr-in-Charge. (ii) Test result of earthing to be submitted by the contractor for all eathing. (iii) The contractor shall have to give written guarantee for maintanance earth resistance of less that 1.0 Ohm. (iv) Failing to maintain resistance of earthing less than 01.0 Ohm, new eathing to be provided by the Contractor. (v) Necessary earth work, excavation shall be carried out in any type of soil strata, returning, filling in and making good surrounding are complete.

M&L for earth continuity conductor fixed to wall/floor/drawn in holes/conduits or any situation as directed of size GI earth wire 4 mm dia including lointing necessary GI protection light grade pi[e 15 mm dia and strips with nuts bolts complete all as specified and as directed.

Taking down or taking down extg steel tubing and connections including cleaning for refixing or removal to store for the following sizes complete all as specified and directed:-

(a) 20 mm (3/4'') dia

(b) 15 mm (1/2'') dia

Supply and laying for galvanised iron tubing medium grade with and including all fittings such as bends, elbows, tees, short pieces, union etc in trenches of following sizes complete all as specified and as directed :-

(a) 20 mm (3/4'') dia

(b) 15 mm (1/2'') dia

S & F for Gun metal gate valve with iron wheel head screwed both ends ISI marked fixed to GI pipe complete all as specified and as directed of size 20 mm(3/4") dia including removal of old extg one complete all as specified and as directed.

Please Enable Macros to View BoQ information