SPECIAL REPAIRS TO BLDG NO. OWT-341 AND OWT-343 OF INF DIV CAMP, PROVN OF REST ROOM CUM DUTY OFFR ROOM AT HQ INF DIV AND PROVN OF TOILET CUM BATH ROOM NEAR SUTC COY OF INF DIV CAMP AT LIKABALI MIL STN UNDER GE 872 EWS

Amount

B/R SERVICES/WORKS

Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and Removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Brick Work or Pre-cast Concrete Block Masonry, built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed.

Dismantling Timber Scantlings 40 Sq Cm and Over in Section in Unframed Work, Seggregating Serviceable Timber Scantlings and Keep in Safe Custody for Refixing / Reuse, complete all as specified and as directed.

Taking down Chowkat or Frame of any description (without Taking Off Shutter from the Frame) not exc. 1.50 Square Metre Each, complete all as specified and as directed.

Taking down/out Unserviceable Rusted/Worn out Wire Cloth/Netting of any description, fixed with Beads, etc., complete all as specified and as directed.

Dismantling Plain or Corrugated Steel Sheeting of any gauge and thickness, complete all as specified and as directed.

Dismantling Ceiling Frame (Snap Grid) with Hangers (but except Boards) of any descriptions, complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards/ Slabs/ Blankets of any descriptions including Cover Fillets, complete all as specified and as as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing) and removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Dismantling Stone Slabs and/or Tiles of any description or thickness in Floors, Aprons, etc. laid, bedded and pointed in Cement Mortar and removing debris, etc to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Taking down Cement Plaster including Raking out Joints, Hacking for Key, Scrubbing down with Water and Removing Debris, etc. etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Taking up or down Steel Tubing 15mm bore (dia) and Fittings, Segregating the Serviceable Pipes and Fittings, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed.

Taking up or down Steel Tubing 20mm bore (dia) and Fittings, Segregating the Serviceable Pipes and Fittings, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed.

Taking/ Lowering down Unserviceable Water Storage Tank of any description, exc. 250 Litre and not exc. 500 Litre Capacity after disconnecting all Water Pipe Line Connections with Ball Valve, complete all as specified and as directed.

Surface Excavation not exc. 30 Cm deep and ave. 15 Cm deep and getting out in Soft/Loose soil, complete all as specified and as directed.

Excavation in Trenches not exc. 1.50 Metre wide and not exc. 1.50 Metre in depth for Foundation etc. or for Shafts, Wells, Cess Pits, Manholes, Pier Holes, etc. not exc. 10 Sqm on Plan and not exc. 1.50 Metre in depth and getting out as in Soft/ Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering and Well Ramming in layers not exc. 25 Cm, in Soft/Loose Soil, complete all as specified and as directed.

Removing Excavated Materials (Soils) not exc. 50.00 Metre and depositing where directed at a level not exc. 1.50 Metre above the Starting Point, complete all as specified and as directed.

M&L Sand Filling (as approved) under Floors or in Foundations in layers not exc. 15 Cm thick including Watering and Consolidation, complete all as specified and as directed.

M&L Hardcore Broken Stone or Boulders, gauge not exc. 63mm, deposited, spread and levelled in layers not exc. 15 Cm thick, watered and well rammed to a True surface, complete all as specified and as directed.

M&L Cement Concrete 1:3:6 (20mm graded stone aggregate) in Coping, Bed Plates, Benching, Bed Block, Kerb Stones, etc. including necessary Formwork and Weathering, slightly Rounded or Chamfered Angles and Throating, complete all as specified and as directed. NOTE : Cost of Formwork will deem to include in the Quoted Unit Rate.

M&L Cement Concrete 1:4:8 (40mm graded aggregate) in Foundations, Filling and Mass Concrete, etc. including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork will deem to include in the Quoted Unit Rate.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Foundation including Rafts, Footing, Foundation Beams for Column Basement Slab, under Reamed Piles, complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid for separately under appro-priate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Columns, Pillars, Posts and Struts, etc., complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid for separately under appro-priate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Beams, Cantilevers, Bressumers, Lintels over 1.50 Metre Span, etc., complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Pre-cast Reinforced Cement Concrete 1:2:4 (20mm graded aggregate) in Landings, Cover Slabs (for Manholes, etc.), Chullah Hoods, Chajjas, Water Troughs, Mangers, Shelves and Similar Articles with Plain faces and Setting in Cement Morter 1:6, complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid for separately under appro-priate Items.

M&L Formwork to Sides of Concrete Foundations, Footings, Bases of Columns, Raft and Raft Beams, Sides and Soffits (if any) of Foundation and Plinth Beams; and Similar Work; Vertical or to Batter, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides of Pillars, Posts, Struts, Piers, Columns and Stanchions, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides and Soffits of Floor or Roof Beams, Girders, Beam Haunchings, Bress-summers, Lintels, Cantilevers, Shelves including Supports, Overhangs, etc. also splays between Floors and Beams, etc., Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Pre-cast Cement Concrete Block Masonry with Solid Blocks of Size 300x200x200mm or 300x200x100mm, having Compressive Strength of not less than 100 Kg/ Sq Cm (as per IS-2185) in Cement Concrete 1:3:6 (20mm graded stone aggregate), exc. 10 Cm in Width and Setting in Cement Mortar 1:6, complete all as specified and as directed.

M&L Pre-cast Cement Concrete Block Masonry but except Blocks (Serviceable old Blocks obtained from BOQ Item No. 1.002 here-in-before), exc. 10 Cm in Width and Setting in Cement Mortar 1:6, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 40mm thick in Damp Proof Courses to Horizontal or Vertical Surfaces including Use & Waste of Formwork and Applying evenly a coat of Blown type Bitumen @ 1.50 KG/SQM and blinding with Clean Dry Sand @ 0.05 CUM/SQM, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) in Scantling, Cleansawn, Timber fixed (Unframed work), fixing with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) in Scantling but except Timber (Serviceable Timber Scantling obtained from BOQ Item No. 1.003 here-in-before), Timber fixed (Unframed work), fixing with Nails, complete all as specified and as directed.

S&F Factory made Solid PVC Door Frame of Size 50x47mm made out of 5.0mm thick Plain Colour (Ivory Shade) PVC Sheet reinforced with Mild Steel Square Tube and fixing in opening as per Specification and Drawing of MES Schedule Part-II, complete all as specified and as directed.

S&F Factory Made Solid Panel PVC Door Shutter 30mm thick (Style) consisting of Frame made out of Mild Steel Tubes for Top & Bottom Rails, Mild Steel Frame shall be covered with Heat Moulded Plain Color PVC ‘C’ Channel having a PVC Strip of 20mm width stuck inside with Solvent Cement for Stiles & Plain color PVC Sheets for Top Rail, Lock Rail & Bottom Rail on Either Side & Gap insert for Top Rail & Bottom Rail, Paneling of Plain Color PVC sheet to be fitted in the Mild Steel Frame, welded/sealed to the Stiles & Rails with suitable PVC Sheet Beading & jointed together with Solvent Cement, complete all as specified and as directed. NOTE : Builders Hardware will be Measured and Paid seperately under appro-priate Items.

M&L Anodised Aluminium Powder Coated (Thickness of Powder Coating not less than 50 micron) Frame for Doors, Windows, Ventilators with One or More Rebates including Joining Cleat for fixing, etc., complete all as specified and as directed.

M&L Anodised Aluminium Powder Coated (Thickness of Powder Coating not less than 50 micron) Door Shutters, Aluminium Section weighing not less than 0.55 KG/RM including necessary Joining Cleats, Glazing Clips, Rubber/ Neoprene Packing, Handles (as approved) - 2 No. in Each Door, Stainless Steel Hinges of Size as ordered, anodised Aluminium Snap Beading, Screws, etc, complete all as specified and as directed. NOTE : Cost of Aluminium Fittings/ Builders Hardware as metioned here-in-above will deem to include in the Quoted Unit Rate.

M&L Anodised Aluminium Window and Ventilator Shutters, Side Hung type without Sash Bars, Aluminium Sections weighing 0.55 KG/RM including necessary Joining Cleats, Glazing Clips, Rubber Packing, Anodised Aluminium Snap Beading, Screws, Anodised Aluminium Fittings such as Peg Stays 150mm long (1 No.). Hinges Type B-21, 100mm long (2 No.) suitable Handle (1 No.), complete all as specified and as directed. NOTE : Cost of Aluminium Fittings/ Builders Hardware as metioned here-in-above will deem to include in the Quoted Unit Rate.

S&F Steel Ventilator with Top Hung Shutter including Hinges, Steel Peg Stay and fixed, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt of Size 125mm long, Extruded Section, complete all as specified and as directed.

S&F Aluminium alloy, anodised, Sliding Door Bolt 250mm long with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of Size 100mm, complete all as specified and as directed.

S&F Aluminium Handle of Size 125mm, anodised, Cast type, complete all as specified and as directed.

S&F Hat and Coat Hooks, Brass, Solid Body of Size 175mm to 250mm and Fixed-in-repairs, complete all as specified and as directed.

M&L Stainless Steel Curtain/ Drapory Rod having 24mm Outer dia with Wall thickness 1.00mm (minimum) including Brackets, Side Holders and Rings, etc. and Fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed.

S&F Figured Glass, Pin Head type, 3.0mm thick and Glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

S&F Sheet Glass 5.0mm thick, Plain, Ordinary quality and Glazing with Oil Putty in Square, exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

M&L TMT Bars 10mm dia and Over, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8.0mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8.0mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Rolled Mild Steel Sections in Roof Trusses (Framed), Trussed, Purlins, Crane Gantries, Rails and Fastenings and Heavy Bracket Framing (Beam, Tee, Angle, Channel or Flat Sections) including Distance Pieces, Cleats, etc., conform to Fe-410-W (Gde E-250) Quality 'A', complete all as specified and as directed.

M&L Plates (Plain or Chequered) Channels, Square cut or Notched (Ordinary and Counter Sunk) forming Holes, without any Aattachment, conforming to Gde Fe-410-W (Gde E-250) Quality 'B', complete all as specified and as directed.

M&L Mild Steel Screw Bolts (Machine made) of any description (Dia of Neck and Length of Bolt as ordered/ as per Site requirment), with Hexagonal or Square Heads at One End and screwed the Other End, or screwed Both Ends, Each screwed End to be fitted with Washers and One Hexagonal or Square Nut, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Plain Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Ridges/ Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

M&L Exposed Suspended False Ceiling System with GI Powder Coated Snap Grid/ Frame Work of Size 605x605mm, all as per Specification and Drawing of MES Schedule (except Hangers), complete all as specified and as directed.

S&F Hangers 4.0mm dia GI (upto 1200mm length) for adjusting Level, fixed to Roof Slabs by means of Ceilling Cleats made out of GI Flat 40x3.0mm in Size, 60mm long and Expansion Hold Fasteners 12.5mm dia, 40mm long, complete all as specified and as directed.

S&F HSPC Non-Asbestos Fibre Cement Building Boards 4.0mm thick, Pre-primed, Self Embossed, Textured Designer Boards, Water Resistant, Termite Resistant, Fire Resistant for insulation, fixed or laid/ inserted to GI/ Aluminum Snap Grid Frame Work with Screws, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 75mm thick in Sub-base to Floors, etc., complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 25mm thick as Base Course for laying Tiles on Flooring, etc., finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Non-skid Ceramic Coloured/ Designer Tiles, Joint Free (1st quality and as approved) 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Non-skid Ceramic Coloured/ Designer Tiles, Joint Free (1st quality and as approved) 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Non-skid Ceramic Coloured/ Designer Tiles, Joint Free (1st quality and as approved) 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Glazed Ceramic Coloured Tiles 350x250x7.0mm or 450x350x7.0mm thick (1st quality and as approved) in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Granite (of any type) Tiles 18mm-20mm thick, Mmachine cut, Bedded and Jointed with Grey Cement Slurry and Pointed with White Cement with Admixture of Pigment to match the Shade of Granite Stone including Grinding and Polishing, fixing over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) 75mm thick in Plinth Protection, etc., Laid in Alternate Panels, finished Concrete Surfaces even and smoooth without using extra Cement, complete all as specified and as directed

M&L Joint Filling on Plinth Protection with 1 Part of Bitumen and 3 Parts of Sand, complete all as specified and as directed.

M&L Rendering 10mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:4 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering 15mm thick on Bricks/Pre-cast Blocks or Concrete Works consisting in 2 layers, Backing/Under layer of 10mm thick in Cement Mortar 1:4 and Float/Top layer 5.0mm thick in Cement Mortar 1:4 including mixing WPC to Float/Top layer, finished Fair and Even, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) will be Measured and Paid separately under appropriate Item,

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Wall Care Putty 3.0mm thick in Two Coats (1.5mm thick in Each Coat) on Plastered Surfaces of Walls including Cutting and Rubbing down to obtain an Even and Smooth Surface, complete all as specified and as directed.

M&L Applying Two Coats of Distemper Oil Emulsion (as approved) over a Coat of Chalk Whitening (Priming Coat) on Putty Finished Surfaces, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Cement Based Paint (of approved Tint) over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Old Painted Wooden Surfaces of any description, exc. 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality Paint of approved Tint), complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any descriptions, exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing Old Treated Steel and Iron Surfaces of any descriptions, exc. 10 Cm in Width or Girth and Applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint), complete all as specified and as directed.

M&L Preparing New or Previously Treated Surface of Wood and Wood based Materials of any description and girth and treated with Two Coats of Creosote Oil, complete all as specified and as directed.

S&F Galvanised Steel Tubing 15mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

Refixing Old Steel Tubing 15mm bore (dia) and Fittings (Serviceable Pipes and Fittings obtained from BOQ Item No. 1.012 here-in-before) in New or Old Position (Walls, Ceiling, Floors, etc.) including Cleaning both Inner and Outer Surfaces of Pipes & Fittings by using Wire Brush including provision of New GI Fittings (as required ordered at Sites), complete all as specified and as directed.

S&F Galvanised Steel Tubing 20mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

Refixing Old Steel Tubing 20mm bore (dia) and Fittings (Serviceable Pipes and Fittings obtained from BOQ Item No. 1.013 here-in-before) in New or Old Position (Walls, Ceiling, Floors, etc.) including Cleaning both Inner and Outer Surfaces of Pipes & Fittings by using Wire Brush including provision of New GI Fittings (as required ordered at Sites), complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia) Cast Copper alloy, Chromium Plated, Fancy type, with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule and Fixed-in-repairs (06 No.), complete all as specified and as directed.

S&F Pillar Tap 15mm bore (dia), Cast Copper alloy, Chromium Plated, with Capstan Heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with Long Screwed Shanks and Fly-nuts, screwed for Iron Pipe and Fixed-in-repairs (02 No.), complete all as specified and as directed.

S&F Stop Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions and Fixed-in-repairs (05 No.), complete all as specified and as directed.

S&F Gun Metal Globe/Gate Valve 20mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe, complete all as specified and as directed.

M&L Rotational Moulded Polyethene Water Storage Tank 500 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS:12701-1996, hoisted and fixed in Position all as specified in MES Schedule and providing Water Pipe Line Connections, complete all as specified and as directed.

S&F PTMT Ball Valve 20mm bore (dia), having weight not less than 210 Gram, high pressure with Epoxy Coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe, complete all as specified and as directed.

S&F Vitreous China White Wash Down Water Closet Pan (Pedestal Pattern) with PVC (SWR) ‘P’ or ‘S’ Trap, and Fixing Bolts and Making Good to Floor/ Distrubed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs (02 No.), complete all as specified and as directed.

S&F White Plastic Water Closet Seat and Cover for Water Closet Pan (Pedestal Pattern), Closed Pattern with Flat bottom and Cover and Mild Steel Chromium plated or Aluminised Hinging Device and Fixed-in-repairs (02 No.), complete all as specified and as directed.

S&F Jet Spray with Connection Pipe 15mm bore (dia), Brass Chromium Plated (as approved) and suitable for Wash Down Water Closet Pan (Pedestal Pattern) and Fixed-in-repairs (02 No.), complete all as specified and as directed.

S&F Toitet Paper Holder of size 150mm (as approved), Brass Chromoum Plated with Rod to hold Paper Roll and Fixing-in-repairs (02 No.), complete all as specified and as directed.

S&F PVC Flushing Cistern 10 Litre capacity White, Low Level, Valveless, Syphonic Action type with Inlet, Ball Valve, Float & Handle, and PVC Flush Pipe 32mm bore (dia) of suitable Length, a Pair of Cast Iron Brackets/ Erecting Stand duly painted including cutting and pinning in Ends, Making Good disturbed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs (02 No.), complete all as specified and as directed.

S&F Vitreous China White Wash Hand Basin 550x400mm in Size, Flat Back with Brass Chromium Plated Waste Fitting 32mm bore (dia) and PVC Waste Pipe 32mm/40mm bore (dia) of suitable Length, a Pair of Cast Iron Brackets/ Erecting Stand duly Painted, Cutting and Pinning in Ends and Making Good Disturbed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs (02 No.), complete all as specified and as directed.

S&F PVC Connection Pipe 15mm in Size and 450mm in length with PTMT Nuts suitable for connecting with Flushing Cistern, Wash Hand Basin, etc. and Fixed-in-repairs (04 No.), complete all as specified and as directed.

S&F Brass Chromium plated Overhead Shower Rose 125mm in Size with Arm and Flanges, with or without Swivel Joints including fixing to GI/ Steel Pipe 15mm bore (dia) or Union and Fixed-in-repairs (02 No.), complete all as specified and as directed.

S&F Soap Dish not less than 150mm in Size, Chromium plated, Fancy type (as approved), fixed on Wall with Wooden/ PVC Cleats and Brass Chromoum Plated Screws and Fixed-in-repairs (02 No.), complete all as specified and as directed.

S&F Tubular Towel Rail 20mm dia, Brass Chromium Plated, D-type, 60 Cm long between Flanges with Bracket (One Pair), fixed to Wall with Brass Chromoum Plated Screws on Wooden/ PVC Cleats and Fixed-in-repairs (02 No.), complete all as specified and as directed.

S&F Sheet Glass Shelf Assembly, consisting of 5.5mm thick Sheet Glass Shelf 12 Cm Wide with Chromium plated Bracket Guard and Railing 60 Cm Long, fixing to Walls with Brass Chromoum Plated Screws on Wooden/ PVC Cleats and Fixed-in-repairs (02 No.), complete all as specified and as directed.

S&F Chromium Plated Grating Doom 100mm dia with Waste Holes (as approved) and Fixed-in-repairs (05 No.), complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Floor Trap having Diameter of Outlet 75mm, Plain with Grating including Jointing with Solvent Cement and Fixed-in-repairs (05 No.), complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, laid in Trenches or laid in Flors, complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, fixed to Walls and Fixed-in-repairs (11.00 RM), complete all as specified and as directed.

S&F PVC (SWR) Bend 75mm bore (dia) with Access Door, any Radius, etc. and Jointing with Solvent Cement and Fixed-in-repairs (04 No.), complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, laid in Trenches or laid in Flors, complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, fixed to Walls and Fixed-in-repairs (20.00 RM), complete all as specified and as directed.

S&F PVC (SWR) Bend 110mm bore (dia) with Access Door, any Radius, etc. and Jointing with Solvent Cement and Fixed-in-repairs (04 No.), complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) in Concrete Bed to Drain Pipes of 160mm bore (dia) including Packing Under and Haunching against the Sides of Pipes after they are laid and tested; complete all as specified and as directed. NOTE : Necessary Earth works will be Measured and Paid separately under appropriate Items.

S&F PVC (SWR) 160mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, laid in Trenches and Tested after laid, complete all as specified and as directed. NOTE : Necessary Earth works will be Measured and Paid separately under appropriate Items.

M&L Cutting into existing Manholes for Connecting PVC (SWR) Drain Pipe 160mm bore (dia), Making Good to Pipe and Rendering, Cutting out existing Benching for and forming Branch Channel (½ Round or ¾ Section) in Cement Concrete 1:2:4 (20mm graded stone aggregate), Smooth Finished and Reforming Benching as required, complete all as specified and as directed.

E/M SERVICES/WORKS

M&L Taking down carefully Copper Point Wiring (Light, Fan, Socket or Power) complete from in any Position including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets but excluding Light Fittings of any description, Making Good Disturbed Surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (White/Colour Washing, Distempering, Painting, etc.) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Taking down Unserviceable Sub-main Wiring from PVC Conduit/ PVC Casing Capping of any description, Making Good disturbed surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (White/Colour Washing, Distempering, Painting, etc.) wherever required to match the Existing Finishes, complete all as specified and as directed.

Taking down Unserviceable Service Connection Cable/ Wire and connected Items of any description from any Situation, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable with 1.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded single core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/ FAN/ BELL POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated unsheathed multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated unsheathed multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire for ONE 3/5 PIN SOCKET 6 AMP POINT on SAME BOARD, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable with 1.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 2.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable with 2.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6/16 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 4.0 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable with 4.0 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6/16 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Sub-main Wiring with 2-Runs of 6.0 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable and 1-Run of 6.0 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable (Green Colour) as Earth Continuty Conductor drawn through and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32mm width) along with all Fitting/Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc., complete all as specified and as directed. NOTE :- (a) Cost of 3-Runs of Cables & 1-Run of PVC Casing Capping will deem to include in the Quoted Unit Rate and the same will be Mesured as ONE UNIT. (b) Sub-main Wiring will be measured PVC Casing Capping only. Wires required for Looping, etc. as ordered will deem to include in the Quoted Unit Rate.

S&F PVC Rectangular Board/Block of Size 350x300x50mm Deep, Closed Recessed with 3.0mm thick Plastic Laminated Sheet Cover for mounting Swiches, Sockets, Fan Regulators, etc. and Fixed-in-repairs (02 No.), complete all as specified and as directed.

S&F Switch Piano 6 Amp, Single Pole, Flush type, 1-way, 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Unserviceable Switch Piano 26 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Modular Switch 6 Amp, 1-way, Single Pole, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Modular Switch 16 Amp, 1-way, Single Pole, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Socket Outlet 6 Amp, 5 Pin, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Unserviceable Socket Outlet 06 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Modular Socket 6 Amp, 2/3 Pin Combined, 2 Modules, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Modular Socket 6/16 Amp, 2/3 Pin Combined, 2 Modules, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Industrial Switch Socket for AC with Strater, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6 Amp 3/5 Pin & 16 Amp 3/5 Pin, Multi-plug, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Unserviceable Switch Socket Combination 06 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F White Cover Plate with Frame, 2 Modules and fixing, complete all as specified and as directed.

S&F White Cover Plate with Frame, 3 Modules and fixing, complete all as specified and as directed.

S&F White Cover Plate with Frame, 4 Modules and fixing, complete all as specified and as directed.

S&F White Cover Plate with Frame, 6 Modules and fixing, complete all as specified and as directed.

S&F Lamp/ Angle Holder PVC/ Polycarbonate type with Back Plate suitable for Batten Fitting and connecting up, complete all as specified and as directed. NOTE : Unserviceable Lamp/ Angle Holder 02 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Ceiling Rose 65x50mm, 3 Terminals, Surface Bakelite suitable for 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Unserviceable Ceiling Rose 20 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Ceiling Fan Regulator, Electronic, Stepped type, 230 Volt AC including necessary Connection and connecting up, complete all as specified and as directed. NOTE : Unserviceable Fan Regulator 02 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Ceiling Fan Regulator, Dimmar Switch type, 230 Volt AC, Rotary Stepped, Electronic type 120/280 Volt and connecting up, complete all as specified and as directed.

S&F LED Adore 15 Watt (as approved), B22 CDL, 3 Star, Ball Lamp with 4000K and fixing, complete all as specified and as directed.

S&F LED Bed Side Lamp Fitting with LED Lamp (as approved) and Connecting up, complete all as specified and as directed.

S&F LED Light Fitting 1x9 Watt/1x10 Watt Bulk Head Luminaires including LED Light, Driver, Holder, Connecting up with and including 3 Core Flexible Copper Conductor Cable of suitable Size and Length from Ceiling Rose upto Light Fitting and Fixed-in-repairs, complete all as specified and as directed. NOTE : Unserviceable Light Fitting 02 No. against Taking down of Point Wiring will be catered under Schedule of Credit.

S&F LED Decorative Wall Light Fitting 1x9 Watt/1x10 Watt, made of Polycarbo-nate LED Lamp, Holder, Connecting up with and including 3 Core Flexible Copper Conductor Cable of suitable Size and Length, complete all as specified and as directed.

S&F LED Light Fitting 1x18 Watt/1x20 Watt, 4.0 Feet long, 220 Volt, AC Decorative Box type with Driver, Holder, LED Tube 18 Watt/20 Watt, Connecting up with and including 3 Core Flexible Copper Conductor Cable of suitable Size and Length from Ceiling Rose upto Light Fitting and Fixed-in-repairs, complete all as specified and as directed. NOTE : Unserviceable Light Fitting 12 No. against Taking down of Point Wiring will be catered under Schedule of Credit.

S&F LED Luminaire 600x600mm, 34 Watt/ 36 Watt, 220 Volt AC, Recessed type Unique Slim with High Efficiency PMMA Diffuser Soft Glare Free Light complete with Driver, Holders & LED Lamps suitable for Roof Ceiling, Connecting up with and including 3 Core Flexible Copper Conductor Cable of suitable Size and Length inclduding Cutting to Existing Ceiling as required/ ordered and Fixed-in-repairs, complete all as specified and as directed. NOTE : Unserviceable Light Fitting 02 No. against Taking down of Point Wiring will be catered under Schedule of Credit.

M&L Taking down Ceiling Fan, Exhaust Fan of any Make and Sweep from any Height after disconnecting Electric Connection and Keep in Safe Custody for Re-fixing / Re-hanging, complete all as specified and as directed.

M&L Transporting Ceiling Fan 1200mm Sweep from the Site of Work at LIKABALI to nearest Workshop, Removing burnt Winding of any type, Cleaning Slot, Rewinding Fan Motor with Super Enamalled Copper insulated Wire of suitable Gauge and Weight (not less than 350 Gram) providing necessary Insulation Materials, Varnishing, Heating, Reassembling & Testing for Smooth Functioning after Rewinding, Removing the Fan to Site of Work after Rewinding, complete all as specified and as directed.

M&L Mild Steel Flat Iron 40x5mm in Fan Hooks, Cut to Length, bent to Shape as ordered, drilling holes for Bolts including providing Mild Steel Bolts, Nuts and Washers, conforming to Fe-290 Gde-E-165 and Fixed-in-repairs, complete all as specified and as as directed.

M&L Re-hanging/Refixing only Ceiling Fan, Exhaust Fan (obtained from BOQ Item No. 2.033 here-in-before) and Connecting up with and including 3 Core Flexible Copper Conductor Cable of suitable Size and Length from Ceiling Rose to Connector of the Fan, complete all as specified and as directed.

M&L Hanging only Ceiling Fan and Connecting up with and including 3 Core Flexible Copper Conductor Cable of suitable Size and Length from Ceiling Rose to Connector of the Fan, complete all as specified and as directed.

M&L Cutting/ Making Hole in Brick/ Concrete Block Walls built in Cement Mortar to suitable Size for fixing of Exhaust Fan 250mm Sweep with Frame and Making Good in Cement Mortar 1:3 or Cement Concrete 1:2:4 (20mm graded stone aggregate) as required, complete all as specified and as directed.

S&F Exhaust Fan 250mm Sweep made of Sturdy Engineering Plastic complete with Louvers Shutter, 230 Volt, 50 Hz, RPM 1200, Copper Winding, Connecting up with and including 3 Core Flexible Copper Conductor Cable of suitable Size and Length from Ceiling Rose to Connector of the Fan, complete all as specified and as directed.

S&F Miniature Circuit Breaker (MCB) 6 Amp to 32 Amp, Single Pole with rating 240 Volt, 10 KA 'C' Curve, Connecting up and Fixed-in-repairs, complete all as specified and as directed. NOTE : Unserviceable MCB 12 No. obtained from Taking down/ out will be catered under Schedule of Credit.

S&F Miniature Circuit Breaker (MCB) 6 Amp to 32 Amp, Single Pole & Neutral, 'C' Series, 50 Hz, 10 kA, 240 Volt, Connecting up and Fixed-in-repairs, complete all as specified and as directed. NOTE : Unserviceable MCB 04 No. obtained from Taking down/ out will be catered under Schedule of Credit.

S&F Miniature Circuit Breaker (MCB) 40 Amp to 63 Amp, Single Pole & Neutral, 'C' Series, 50 Hz, 10 kA, 240 Volt, Connecting up, complete all as specified and as directed.

S&F Miniature Circuit Breaker (MCB) 16 Amp to 32 Amp, Triple Pole & Neutral, 'C' Series, 50 Hz, 10 kA, 415 Volt, Connecting up and Fixed-in-repairs, complete all as specified and as directed. NOTE : Unserviceable MCB 02 No. obtained from Taking down/ out will be catered under Schedule of Credit.

S&F Sheet Metal Enclosure for DB's when MCBs to be used 2-Way, SPN, 240 Volt, Single Door, Epoxy Based Powder Coated Painted, suitable for mounting MCB DP/SPN, Connecting Cable Links and Connecting up including Taking down/ out Unserviceable MCB DBs (02 No.) of any description, complete all as specified and as directed.

S&F Sheet Metal Enclosure for DB's when MCBs to be used 4-Way, SPN, 240 Volt, Single Door, Epoxy Based Powder Coated Painted, suitable for mounting MCB DP/SPN as Incomer and MCB SP as Out-going with 200 Amp rated Bus-bar, Neutral Bar, Earth Bar, Connecting Cable Links and Connecting up, complete all as specified and as directed.

S&F Sheet Metal Enclosure for DB's when MCBs to be used 4-Way, SPN, 240 Volt, Double Doors, Epoxy Based Powder Coated Painted, suitable for mounting MCB DP/SPN as Incomer and MCB SP as Out-going with 200 Amp rated Bus-bar, Neutral Bar, Earth Bar, Connecting Cable Links and Connecting up including Taking down/ out Unserviceable MCB DBs (02 No.) of any description, complete all as specified and as directed.

S&F Sheet Metal Enclosure for DB's when MCBs to be used 8-Way, SPN, 240 Volt, Double Doors, Epoxy Based Powder Coated Painted, suitable for mounting MCB DP/SPN as Incomer and MCB SP as Out-going with 200 Amp rated Bus-bar, Neutral Bar, Earth Bar, Connecting Cable Links and Connecting up including Taking down/ out Unserviceable MCB DBs (02 No.) of any description, complete all as specified and as directed.

S&F Sheet Metal Enclosure for DB's when MCBs to be used 12-Way, SPN, 240 Volt, Double Doors, Epoxy Based Powder Coated Painted, suitable for mounting MCB DP/SPN as Incomer and MCB SP as Out-going with 200 Amp rated Bus-bar, Neutral Bar, Earth Bar, Connecting Cable Links and Connecting up, complete all as specified and as directed.

Supply and Laying or Fixing or Passing through Pipe, 1100 Volt grade Heavy duty Cable with PVC insulated Aluminium Stranded Conductor served with an Inner sheathing of PVC Tape armoured with Galvanised Steel Wire or Tape and Overall PVC sheathed, Nominal Cross section 10 Sqmm 2 Core in Service Connection, complete all as specified and as directed.

Supply, Installation & Commissioning Factory Made LT Feeder Pillar Box (CPRI Approved/ Tested Manufacturer) made out of 3.15mm thick CRCA Sheet, Outdoor type, suitable for 415 Volt, 3 Phase, 4-Wire System, 50 Hz Supply, Platform mounted of Size 600x500x450mm, Dust Proof and Vermin Proof (IP54), Epoxy Powder coated, Front & Rear Opening, Double Door Shutters with Locking Arrangements, Feeder Pillar Box having Epoxy Powder coated, mounted on Mild Steel Angle Iron Frame 50x50x6.0mm and not less than 600mm Height from Natural Ground Level, grouting Angle Iron Legs in Cement Concrete 1:2:4 (20mm graded stone aggregate) Block of Size 300x300x600mm including necessary Formwork, Earthwork, expossed Angle Iron Frame shall painted with Two Coats of Synethetic Enamel Paint over a Coat of Red Oxide Zinc Chrome Primer, Providing all Electric Connections and Testing, Comprising with and including following, complete all as specified and as directed :- (a) Copper Bus-bar 200 Amp, 4 Strip, installed on Porcelain/ Epoxy - 01 Set Insulators (b) MCCB 63 Amp, 4 Pole, 25 kA, 415 Volt - 01 No. (c) MCCB 63 Amp, 3 Pole, 25 kA, 415 Volt - 01 No. (d) Digital Amp Meter 0-200 Amp Square Flush Pattern - 01 No. (e) Digital Voltmeter 0-500 Volt, Square Flush Pattern - 01 No. (f) LED Indicator Lamp (RYB) in Incomming Phase - 01 Set (g) Internal Wiring with PVC insulated Copper Conductor Multi-stranded Cable 1100 Volt, IS:694 marked of appropriate Gauge including all Copper Lugs (h) MCCB shall be provided with suitable Spreaders of Copper Conductor for fixing of Incoming Cables (j) Connection from MCCB to Bus-bars with Solid Copper Conductor.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of Size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing including Taking down/ out Unserviceable Earthing (02 Set) of any description, complete all as specified and as directed.

Excavating in Trenches, not exc. 1.50 Metre Wide and not exc. 1.50 Metre in Depth for laying of Water Pipe Lines, Cable Lines, etc., Forming Surfaces to required Foundation/ Gradient and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering, Well Ramming in Layers not exc. 25 Cm, Providing Heaps with Surplus Soil along the Route of the Water Pipe Lines, Cable Lines, etc., in soft/loose soil, complete all as specified and as directed.

M&L XLPE insulated, armoured heavy duty, Electric Cable with Aluminium Conductor, 1100 Volt grade, Cross-sectional area 35 Sqmm, 3½ Core, laid in Trenches / Ducts or Passing through Pipes or Fixing on Poles, etc., complete all as specified and as directed. NOTE : Necessary Earth works, Sand cushioning, Cable Protection Cover & GI Pipe, etc. will be Measured and Paid separately under relevent Items.

M&L Sand Cushioning (dry) in Trenches/Ducts for protection of UG Cables (below, above and around the UG Cable laid) of 23 Cm Spread thickness (8 Cm in depth before laying the Cable and 15 Cm in depth after laying the Cable) and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. NOTE : For the purpose of Payment, Punned thickness of Sand Cushioning only will be Measured.

Supply & laying Sub-class ‘B’ Bricks of Size 230x115x75 mm, Kiln burnt, for Covering to UG Cable as Protection, laid Flat, Transversally Width Equal to the Length of the Cable, complete all as specified and as directed.

Supply & laying Steel Water Tubing 20mm bore (dia), Galvanised, ‘medium grade’ with all Fittings, laid in Trenches or any other Situation, complete as all specified and as directed. NOTE : Necessary Earthworks will be Measured and Paid saperately under appropriate Item.

Supply & laying Steel Water Tubing 25mm bore (dia), Galvanised, ‘medium grade’ with all Fittings, laid in Trenches or any other Situation, complete as all specified and as directed. NOTE : Necessary Earthworks will be Measured and Paid saperately under appropriate Item.

Supply & laying Steel Water Tubing 40mm bore (dia), Galvanised, ‘medium grade’ with all Fittings, laid in Trenches or any other Situation, complete as all specified and as directed. NOTE : Necessary Earthworks will be Measured and Paid saperately under appropriate Item.

S&F Gun Metal Globe/Gate Valve 40mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe, complete all as specified and as directed.

M&L Cutting Cast Iron/ GI Pipes of any Size and reducing to required Length before laying and to Existing Pipe Lines for Taking up Branch Connections and Insertion of Specials, etc. in Position, complete as all specified and as directed. NOTE : Cost of Specials viz New Tees, Branches (as required at Site of Work) will deem to include in Quoted Unit Rate.

M/S Abhi Traders

M/S Raju prasad

Prova Stores

M/S RK Trading

SAHASRA CONSTRUCTION

M/s United Builders

M/S Build Tech

M/S R & R D ENTERPRISES

M/s Krishna Construction

M/s PRABIR ENTERPRISE

M/S S. P. ENTERPRISE