Special Repairs to hard standing infront of MT Area of Inf Bn-II and plastering, tiling flooring, plumbing, joinery, sanitary, roof treatment and E/M work to Bldg No P-79 at Military Station Fazilka

Amount

SCHEDULE 'A' SECTION I (B&R Portion)

Taking down chowkats or frame with shutters(without taking off shutters from the frame not exceeding 1.50 sqm each & removing to store all as specified and directed by Engineer - in-Charge.

Taking down chowkats with shutters(without taking off shutters from the frame exceeding 1.50 sqm each but not exceeding 4 sqm) removing to store all as specified and directed by Engineer - in-Charge.

S&F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tubes, as per specifications and drawing complete or as directed by Engineer-In-Charge.

S&F factory made solid PVC door shutter 30mm thick(style) consisting of frame made out of MS tubes for bottom and top rails. MS frame shall be covered heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail& bottom rail on either side & as gap insert for top rail & bottom rail; Panelling for plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, suppling and fixing in the frame at the site as per specification.

S&F Aluminium handle cast type anodized 125 mm long all as specified and directed by Engineer-in-Charge.

S&F Aluminium anodized barrel tower bolt of extended section and fixed 150 mm long all as specified and directed by Engineer-in-Charge.

S&F 100 mm long butt hinges extruded almiunium alloy with galvanised mild steel hinges pin, anodised and fixed all as specified and directed by Engineer-in-Charge.

S & F pressed steel door frames with one or more rebates including necessary fixing lungs hinges lock strike plate etc complete all as specified size of frame 105 x 60mm all as specified and directed by Engineer - in - Charge .

S & F pressed steel door frames with one or more rebates including necessary fixing lungs hinges lock strike plate etc complete all as specified size of frame 125 x 60mm all as specified and directed by Engineer - in - Charge .

Ditto Ser no-09 as above but size 75x60 mm as in cup board frames all as specified and directed by Engineer - in-Charge.

M&L Cement concrete 1:2:4 type B–1 filling of pressed steel frame and hold fast blocks etc all as specified and directed by Engineer - in - Charge.

S & F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; size of members of shutters as specified in SSR Part – I, Section – 8, clause 8.20 (a) ; supplied and fitted to chowkats all as specified.

S & F flush shutter 35mm thick solid core construction with block board core and plywood face panels commercial type on both sides with lipping / frame to match all as specified and directed by Engineer - in - Charge.

S&F in repair MS 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-Charge.

M&L 18-20 mm thick block board ,grade 2 quality ,interior grade ,decorative type with decorative face veneer on one faces including wooden beeding around the edges of board ,fixed with screws to Pressed steel frame work all as specified and directed by GE.

S&F Stainless steel tower bolt 150mm long heavy duty all as specified and directed by Engineer - in - Charge.

S&F stainless steel handles of size 150mm heavy duty all as specified and directed by Engineer - in - Charge.

S&F 250mm Stainless steel sliding door bolts, plate type, with bright bolt not less than 12mm dia and including minimum of 6 bolts and nuts, four on bolt plate and two on staple complete all as specified & directed.

M&L preparing surface of wood and wood based surface new on any description not other wise described over 10cm with or grith and applying two coat of synthetic enamel paint over a coat of pink primer all as specified and directed by Engineer - in - Charge.

S & F in repair steel window 1.25 mm thick Box type (primer coated) ERW hollow P section of size 60 mm x 25 mm single rebated comprises gauged skelton shutter ERW Section 50 mm x 20 mm and 1 mm thick with two open able leaf consisting two Nos of sash bars of flat iron 12 mm x 3 mm complete welded to frame with one vertical mullion of ERW box type T section of size 60 mm x 25 mm and 1.25 mm thick including cutting holes and making good dismantled portion in PCC (1:2:4) type B-1 four Nos for each window including following fitting welded to the frame shutter : (a) Hold fast 150 mm long of 12 mm x 3 mm made to shape - 04 Nos per window. (b) Handle of Z section 20 mm x 25 mm, 100 mm long 1 Nos per leaf. (c) MS tower bolt 150 mm long - 2 Nos per leaf. (d) MS pintol hings of size 100 mm x 14 mm - 2 Nos per leaf. (e) Z section 20 mm x 25 mm x 100 mm long stopper per leaf. Note : Wire mesh and painting shall be measured & paid seperately under appropriate items.

S & F in repair steel window 1.25 mm thick Box type (primer coated) ERW hollow P section of size 60 mm x 25 mm single rebated comprises glazed shutter ERW Section 50 mm x 20 mm and 1 mm thick with two open able leaf consisting two Nos of sash bars of flat iron 12 mm x 3 mm complete welded to frame with one vertical mullion of ERW box type T section of size 60 mm x 25 mm and 1.25 mm thick including cutting holes and making good dismantled portion in PCC (1:2:4) type B-1 four Nos for each window including following fitting welded to the frame shutter : (a) Hold fast 150 mm long of 12 mm x 3 mm made to shape - 04 Nos per window. (b) Handle of Z section 20 mm x 25 mm, 100 mm long 1 Nos per leaf. (c) MS tower bolt 150 mm long - 2 Nos per leaf. (d) MS pintol hings of size 100 mm x 14 mm - 2 Nos per leaf. (e) Z section 20 mm x 25 mm x 100 mm long stopper per leaf. Note : Glass and painting shall be measured & paid seperately under appropriate items.

S & F in repair steel ventilators fixed type 1.25 mm thick Box type (Primer coat) ERW hollows P section of size 60 mm x 25 mm single rebated optional full glass or wire mesh.

S&F in repairs MS 10mm bars and over for guard bars plan welded to steel window and similar articles conforming to Fe-290 Gde E- 165 complete all spd.

M&L applying two coats of synthetic enamel paint over a coat of red oxide 0r zinc chromate primer including preparation of new steel or iron surfaces exc 10 cm width or girth, complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint on old decorated steel surfaces exc 10 cm width or girth including preparation of surfaces , complete all as specified and directed.

S&F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanesed wire stapels complete all as specifed and directed.

S & F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.50 sqm in each paneall as specified and directed by Engineer - in-Charge.

S & F 3 mm thick pin headed sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed by Engineer - in-Charge.

S & F continous (Piano)type hinges mild steel bright finish or lectro galvanised with wide of flaps 30mm complete all as spd and directed.

S & F 75mm size stainless steel bright finish handle, fancy type for cupboard shutter all as specified and directed by Engineer-in-Charge.

S&F Stainless steel tower bolt 150mm long heavy duty all as specified and directed by Engineer - in - Charge.

M & L rendering 15mm thick water proofing plaster in CM 1:3 on slab / roof admixed including and with Dr. Fixit pidilite LW+@ 200 ml per bag of cement.

Preparation of roof top surfaces, providing and applying UV stable single component smart care damp proof ultra is a fibre reinforced elastomeric liquid applied water proofing membrane formulated with PU hybrid polymers and reinforcing acrylics fibres and having SRI of 106 on top of concrete roof surface in three coats including self primer at ratio pf damp proof and water 3:1 and coverage @ 1 Ltr /10 sqm with a thickness of 650micron Note: 6 Hrs interval between two coats will be maintain& the work will be carried out through company applcator duly got approved from Accepting officer in writing before incorporation and paid only after receiving of the warrenty certificate from the company. Make : Asian paint or equivalent as approved by GE

M&L marble work 18-20 mm thick in single piece ( table rubbed and polished) in steps,Jams, pillars , windowcills,cooking platform and like in cement mortor (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigments to match with marble shade(Green) as aprroved by Engr-in-charge.

M&L marble work 18-20 mm thick in single piece ( table rubbed and polished) in riser of steps,skirrting ,dado and pillars in cement mortor (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigments to match with marble shade(Green) as aprroved by Engr-in-charge.

Taking down cement or cement lime plaster from brick walls etc including raking out joints, hacking for key scrubbing down with water etc.

M & L rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even & smooth without using extra cement all as specified and directed by Engineer - in - Charge .

M & L rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even & smooth without using extra cement all as specified and directed by Engineer - in - Charge. Note :- Plaster shall be provided in two layers i.e. First layer 10mm and other layer 5mm thick with WPC with 2 % by weight of cement. .

M & L 10mm thick rendering in Cement Mortar 1:3 on fair faces of brick work or concrete surfaces of ceiling finished even and smooth without using extra cement complete all as specified and directed by Engineer - in - Charge .

M & L applying three coat of white wash on newly plastered or unplastered ceiling surfaces including preperation of surfaces, complete all as specified.

M & L Preparation of newly plastered surfaces by applying two coats of interior grade wall putty and making it smooth with sand paper or with hand electric grinder then applying two coats of oil bound distemper over one coat of cement primer all as specified and directed.

M&L weather proof exterior emulsion two coats over a coat of exterior primer including preparation of Newly plastered surfaces and applying two coat of exterior grade wall putty (Asian / JK / Birla) over plastered surfaces making it smooth with sand paper or with hand electric grinder complete all as specified and directed.

M & L Preparation of Old plastered surfaces by removing old treatment with sand paper or hand electric grinder and applying two coats of interior grade wall putty and making it smooth with sand paper or with hand electric grinder then applying two coats of oil bound distemper over one coat of cement primer all as specified and directed.

M&L weather proof exterior emulsion two coats over a coat of exterior primer including preparation of surfaces by removal of existing treatment complete(with sand paper or hand electric grinder) and applying two coats of exterior grade wall putty (Asian / JK / Birla) over plastered or unplastered or concrete surfaces making it smooth with sand paper or with hand electric grinder complete all as specified and as directed.

M & L for complete removal of existing treatment and applying two coats of white wash on old decorated plastered or unplastered surfaces of ceiling including preparation of surfaces complete all as specified and directed by Engineer - in - Charge .

M & L for complete removal of existing treatment and applying two coats of white wash on old decorated plastered or unplastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer - in - Charge .

M & L applying three coat of white wash on newly plastered or unplastered wall surface including preparation of surfaces, complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), remving serviceable tiles to stores and and rubbish off the permises.

M&L for glazed ceramic coloured joint free tiles(of approved pattern) in vertical surface 450X 300X 7mm mm thick over 10mm thick rendering in CM 1:4 as in backing coats in walls set and jointed in neat cement slurry and pointed in white or coloured cement all as per specified and directed by Engineer-in-Charge.

M&L Non skid ceramic coloured /printed tiles 7 to 8 mm thick( square /rectangular) area of each tile exc. 0.11 sqm but n. exc, 0.18 sqm and shall be jointed in neat cement slurry and pointed in paste pigmented to tile shade over and incl 15 mm th screed bed in CM 1:6 complete all as specified and directed by Engr in Charge.

M & L vitrified ceramic light shade coloured tiles with matt finish,(with highlighted border pattern) 10 mm thick ( square/ rectangular ) polished, area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement paste pigmented to tile shade over and including 15mm thick cement and sand screed (1:4) complete all as specified and directed by Engineer - in - Charge.

S&F in repairs stainless steel kitchen sink with drainage board of overall size 915x460mm and bowl size 410x330x160mm with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe complete all as directed.

S & F in repairs stainless steel plate rack of size 900x775x250mm of 1mm thick stainless steel of 1st Quality all as specified and directed by Engineer-in-Charge.

S & F drapery curtain rod, mild steel, powder coated 25mm dia with brackets, knobs, end stops etc all as specified and directed by Engineer - in - Charge .

Dismantling water tanks and removing to store of 500 ltr capacity

S & F rotational moulded polythene three layered white coloured water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I of capacity 500 Litres all as specified.Make -

Dismantling water tanks of capacity exceeding 500 litres and not exceeding 1000 litres all as specified and directed by Engineer - in - Charge.

S & F rotational moulded polythene three layered white coloured water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I of capacity 1000 Litres all as specified and directed by Engineer - in - Charge .

M&L ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball with minimum weight 210 gm screwed for 20mm bore iron pipe supplied and fixed complete all as specified and as directed by Engineer-in-charge.

S&F in repairs gun metal globe or gate valve with crutch or butterfly handle screwed bothedns for iron pipe of 15 mm dia all as directed.

S&F gun metal globe or gate valve with crutch or butterfly handle screwed both ends for iron pipe of 20 mm dia all as directed.

Dismantling of CI pips or reinforced concrete pipes 100 mm dia fixed to wall etc complete all as specified and directed.

Dismantling of CI pips or reinforced concrete pipes 75 mm dia fixed to wall etc complete all as specified and directed.

S&F UPVC pipe to be used for carrying sewage nominal dia 100mm single socketed in any length to fit WC out-let, all as specified.

S&F UPVC pipe to be used for carrying sewage nominal dia 75mm single socketed in any length to fit WC out-let, all as specified.

S&F 110mm UPVC bends any radius (with access door)complete all as specified and directed.

S&F 75mm UPVC bends any radius (with access door)complete all as specified and directed.

S&F UPVC floor trap 100mm bore including jointing to waste pipe and fixed with PCC 1:2:4.

S&F 75mm bore UPVC vent cowl, all as directed.

S&F UPVC reducer coupler 110X75 mm, all as directed.

S&F UPVC single Y branch piece 100 mm bore, all as diected.

Taking down eves and gutter and rain water of any size all as specified and directed by Engineer - in - Charge .

S & F 110mm PVC (SWR) pipes and single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110mm PVC(SWR) bends any radius complete all as specified and directed.

S&F 75mm PVC(SWR) bends any radius complete all as specified and directed.

Taking up or down steel tubing of 15 mm bore and connections, including cleaning for re-fixing or removal to store

Taking up or down steel tubing of 20 mm bore and connections, including cleaning for re-fixing or removal to store

Refixing 20 mm old steel tubing and connections in new or old possition ( wall ceiling floors, etc.)

Supply & fixing mild steel tubes of size 20 mm bore (medium grade) galvanised with all fittingsand fixed complete to wall all as specified.

S&F chlorinated PVC (CPVC) pipes 20 mm outer dia, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.0 m spacing . this includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete all as specified and directed. Make : Supreme/Vectus

S&F in repairs vitreous china wash down water closet pan padestel pattern white including connection pipe to union of flushing cistern, inlet and overflow pipes,connecting only to flushing cistern anti-syphonage pipe with PVC flush pipe of 32mm dia including Jet spray and plastic seat cover with mild steel chromoum plated hinging and 'P' or 'S' trap device complete all as specified and directed by Engineer-in-Charge.

S & F in repairs PVC 10 ltrs syphonic action type flushing cistern, low level with inlet, ball valve, float and handle including brackets, flush pipe of PVC 32mm bore and connection to WC pan complete all as specified .

S&F in repair vitreous china,white, wash hand basin, flat back size 550x400mm 'including MS brackets including cutting for and pinning in, but excluding waste pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repair bib taps long body, 15mm bore dia, fancy type, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe all as specified .

S & F in repairs 15mm bore CP Angle cock one way chromium plated, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified .

S&F in repairs 15mm stop valves fancy type, chromium plated with long shank and cup (concealed type) ,cast copper alloy, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed.

S & F in repair brass chromium plated central hole basin mixer with regular spout , popup waste system and 450mm long braided hoses with connection and nuts complete all as specified and directed by Engr-in-charge.Make ESS ESS or equivalet.

S & F in repairs brass chromium plated wall mixer with non telephonic shower arrangement for mixing hot and cold water screwed down for iron pipe and fixed as directed by Engr-in-charge : Make : ESS ESS Cat Part No .: TM-115 or equivalent.

S & F in repairs for brass chromium plated shower rose 150 x 150 mm size with swivel joint including fixing to 15 mm dia steel pipe or union.

S&F in repairs soap dish,chromium plated, 100X100X60mm, fixed to wall with plugs with chromium plated screws complete all as specified and directed.

S & F brass chromium plated tubular towel rail 20mm dia “D” type 60 cm long between flanges incldg brackets complete all as specified and directed by Engineer - in - Charge .

S&F in repair CP grating suitable for 75/100 mm bore floor trap and fixed with white cement.

S&F in repair PVC connection both side brass unions internal for size 15mm dia and 600mm long all as specified and directed by Engineer-in-Charge.

M & L RCC 1:1½:3, (nominal mix), Type A-1, using 20mm graded aggregates as in chajjas, fins, fascias, louvers, parapets and railing etc and the like including necessary formworks all as specified and directed by Engineer - in - Charge.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for.

Demolition of brick work or stone masonry built in cement mortar including all quoins, pillars, arches etc. but excluding ashlar facings, dressed stone work and precast concrete articles, complete all as specified and as directed.

M&L Brick work with old size burnt fly ash bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 all as specified and directed by Engineer - in - Charge .

M&L 50mm thick PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in plinth protection, surface finished even smooth without using extra cement.

S&F Powder coating aluminium door shutter , aluminium section wt 0.55 kg / mtr including necessary joining cleats ,glazing clips, rubber eoprene packing , handles 2 Nos. in each door , hinges , anodised aluminium snap beading screws etc.

S&F anodized aluminium frame with Powder Coating (minimum thickness of powder coating 50 micron) for doors, windows, ventilators, partitions etc., with one or more rebates including joining cleat for fixing etc complete all as specified and as directed

S & F in repair powder coated aluminum sliding window three track with frame & two glass shutter using 4 mm thick glass tinted modi guard and one shutter with stainless steel wire gauge wire cloth 0.31 mm nominal dia of wire and width of aperture 1.61 mm using aluminum powder coated section aluminum cleat , PVC track, bearing, handle lock rubber beading etc complete fittings as approved. Note :- Size of aluminum section shall be under – (i) three track top and vertical – jindal main 2010. Section No 20621 or equivalent as approved by GE. (ii) Three track bottom – Jindal main – 2010 section 20620 or equivalent as approved by GE. (iii) Shutter Vertical Section - Jindal main – 2010 section 20604 or equivalent as approved by GE. (iv) Shutter top and bottom - Jindal main – 2010 section 20604 or equivalent as approved by GE. (v) Shutter vertical middle ( interlock) - Jindal main – 2010 section 20605 or equivalent as approved by GE.

S&F powder coated aluminum windows and ventilators shutter side hung type without sash, aluminum section weighing glazed clips, rubber packing anodized aluminum fittings such as peg stays 150 mm long (1 nos) hinges type B-21 100 mm long (2 Nos) suitable handle (1 Nos) complete all as specified.

S&F aluminum anodized grill diamond shape 100mm x 100mm aperture of 6 mm dia round bars including necessary joining cleats, clips anodised complete all as specified

S&F door closer hydraulically regulated, aluminium (Die cast) body, designation No. 3, universal type suitable for door shutter upto 1000mm in width complete all as specified and as directed by Engineer-in-Charge.

S&F 100 mm size mortice lock of brass, vertical type,4 levers, complete all as directed.

Dismantling wall and ceiling board or insulation boards/ slabs/ blankets, any thickness, including cover fillets.

S&F false ceiling of 9.5mm thick gypsum tiles (600mmX600mm) laminated with PVC film on the face & side and metalised polyester film on the back side with all four edges sealed with PVC film (shade either plain white or crack) fixed using T grid/Cross-T/wall angle/level clip & suspended/hangers 4 mm dia. GI wire (upto 1200 mm length) adjusting level fixed to roof slabs/trusses complete all as specified and as directed. Make : Saint Gobain / Armstrong / Everest

Demolition of cement concrete in ground floor and paving n.exc 15 cm below or above ground level.

M&L 75 mm thick PCC 1:4:8 type D2 using 40 mm graded aggregate as in sub base complete all as specified and directed by Engineer-in-Charge.

M & L for chequered cement concrete designer prepolished glossy finished tiles of any size ,coloured (Yellow/Red) ,25 thick with grey cement and pigments, heavy duty, set jointed and pointed in neat cement slurry and pigments as in floors over and including 15mm thick screed bed of cement mortar 1:4 complete all as specified and directed by Engineer - in - Charge.

M & L PCC 1:2:4, type B-1 , using 20mm graded stone aggregate as in kerbs or mud stops, rounded or chamfered on edges and similar work all as specified and as directed.

M&L for 5 mm thick plywood, 7 Nos of ply, grade BWP, type BB fixed with screws to timber frame-work complete all as specified and directed.

M&L two coats of french polishing on new wooden surfaces of any description, width or girth including cleaning and preparation of surfaces including a coat of wood filler complete all as specified and directed.

M&L two coats of french polishing on old wooden surfaces of any description, width or girth including cleaning and preparation of surfaces including a coat of wood filler complete all as specified and directed.

S & F PVC wall panelling ,hollow cored , 5mm thick ,decorative designs with smooth surfaces , fire resistant,water and heat proof,tongue and grooves edges for easy assembly with all acessories such U cap ,end cap ,Tee , plugs, fillets and srews etc and fixing as per manufactures instructions and fixing complete all as specified and directed by Engineer-in-Charge.

Demolation of ashlar facings, dressed stone work, stone slabs or tiles from paving and precast concrete blocks and articles all as specified.& directed by Engineer -in-charge..

M&L 18- 20mm thick granite (of any type ) work (table rubbed and polished ) in cooking platform and like in cm (1:4) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shed of granite.

M&L 18-20mm thick machine cut kota stone slab (table rubbed and polished) as in flooring laid over and including 15 mm thick screed bed or bedding layer in CM (1:4), set and jointed with grey cement slurry mixed with pigment to match the shade of slab including cutting, rubbing, grinding and mirror polishing upto desired satisfaction of Engr In Charge complete all as specfied and directed.

S & F in repairs of framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel')

S & F mild steel screw bolts (machine made) 11 to 15mm dia with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long

M&L for rough cast plastering including 15 mm thick rendering in CM 1:3 complete as specified in SSR Part I, clause 14.22. Note : Rough cast finish to be as follow :- After applying the under coat of cement mortar 1:3 and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (which is generally of size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1:1: shall be applied and finished even. the mix of cement and sand shall be made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered.

Supply only liquid water proofing compound complete all as specified and as directed by the Engineer-in-Charge. Make: Dr Fixit/Fosroc/BASF/STP

Demolation of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided.

M&L PCC 1:4:8 type D 2 using 40 mm graded stone aggregate as in sub base.

S&F machine pressed precast concrete interlocking paver block with grey cement & pigment, any shape and size confirming to IS 15658-2006 of 80mm thick M-40 grade including and over 25mm thick sand cushion.

SCHEDULE 'A' SECTION-II (E&M PORTION)

Taking down carefully existing aluminium/Copper point wiring light, fan socket or power bell complete with fitting such as sockets, ceiling roses, pendants batten holders regulators socket, call bells & making good to the disturbed surfaces of walls, matching the colour with existing Surface all as spd and directed by Engr-in-Charge. Note: Rate for making good shall be deemed to be included in above item rate.

Taking down unserviceable main switches and MCB distribution boards single phase complete all as spd

M & L for point wiring complete with 1.5 Sqmm (Nominal area) PVC insulated multustranded fire retardant (low smoke unsheathed and multicore copper conductor cable with colour code ISI marked and including PVC concealed conduict ISI marked and conduit fittings for one light point/fan point/5 Amps switch socket/bell/engagement light controlled by one switch including PVC insulated 1.5 Sqmm single core copper earth wire to common earth and connecting to earth dolly and including suitable MS sunken box of suitable size and covered with & including 3 mm thick bakelite, laminated hylem sheet top cover etc complete all as specified (Cost of MS sunken box and bakelite sheet included in the rate).

All as per Srl item No. 134 here-in-before but one three pin socket outlet 5 Amps on the independent board complete all as specified.

All as per Srl item No. 134 here-in-before but one three pin socket outlet 5 Amps on the same board complete all as specified.

All as per Srl item No.134 here in before but with 1.5 Sqmm (nominal area) PVC insulated multistranded copper conductor cable unsheathed ISI marked controlled by two way switches complete all as specified.

M&L for point wiring complete with 2.5 Sqmm (Nominal area) PVC insulated multistranded fire retardant low smoke unsheated and stranded copper conductor cable ISI marked in and including PVC concealed conduit medium quality and conduit fitting for 3 pin 15 amp multicore switch socket combination including PVC insulated 2.5 Sqmm single core copper earth wire to common earth and connected to earth dolly and including suitable MS sunken box of suitable size and covered with & including 3 mm thick bakelite, laminated hylem sheet top cover etc complete all as specified.

S&F switch Piano type single pole one way 5 Amp,230 VAC supply.

S&F switch Piano type single pole two way 5 Amp,230 VAC supply. .

S&F socket two in one ,3 Pin 5 Amps 230 VAC supply, .

S&F switch Piano type single pole one way 15 Amp on laminated sheet top cover complete to all as spd (Sheet top cover incl in point wiring) .

S&F socket Pinao type 6 Pin 16 amp,230 VAC .

Supply & fixing PVC Lamp holder suitable for and including batten fittings ,LED Electric lamp 9 Watt with backalite 20mm back plate complete all as specified & directed, .

M&L for Ceiling Rose, surface bakelite 12 to 3 terminal, 240 volts, 5 Amp ISI marked complete all as specified and directed.

S&F of fan regulator step down electronic type heavy duly flush type 230 volts AC single phase fixed on laminated sheet top cover (laminated top cover is included in point wiring) and connecting up complete all as specified and directed. (Laminated sheet top cover and sunken box is included in point wiring).

M&L for LED 10W bulkhead fitting with IP-43 engineering plastic housing with clear ,single phase 240V, including 1.0sqmm copper flexible cable twiested three core alongwith flelxible PVC condiut from ceiling rose to fitting testing complete all as specified and directed .

S&F of Exhaust fan heavy duty 300mm sweep mounted in suitable opening arrangement with louvers shutters suitable for operation on 230 volts, single phase, 50 cycle per second, AC supply and connecting up including three core PVC insulated PVC sheated copper conductor flexible cable 24/0.2mm drawn in flexible PVC conduit and fixed by using 4 Nos. 200mm long 12mm dia bolts, nuts and washers and grouted in wall in CM 1:3 complete all as specified and directed.

S&F and testing LED light fitting 1x18watt 4 feet long including LED tube with driver complete suitable for fixation on wall/roof with body robust, corrosion resistant, superior finish and without any cracks or through h oles. The system wattage of fitting should not be more than 18 watt= 10%, surge protection of minimum 2 KV power factor should be more than 0.90 cool while colour, total hormonic distoration (THD) should not be more than 15% lumen output should not be less than 1700 lumens, total input voltage range 140-280V AC, colour rendering index should not be less than 80, Corelated colour should be minimum 6000 degree Kelvin.

Excavation in trenches, not exc 1.5 m wide and n. exc 1.5 m depth; or n exc 10 Sqm on plan and n exc 1.5 m in depth for foundations of poles, struts, stays etc. or laying underground cable etc. in soft/loose soil, & getting out complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25cm thick complete all as specified and directed by Engineer-in-Charge

Removal of excavated surplus soil to a distance n.exc 50m and depositing where directed at level not exceeding 1.5 m above the starting point complete all as specified & directed by Engineer-in-charge .

M & L for sand cushioning with dry coarse sand to under ground cable 23 cm thick, 8 cm thick below the cable and 15 cm thick after laying the cable complete all as specified and directed by Engineer-in-Charge. Note : Thickness after punning shall be considered for payment.

M & L for brick protection with old size sub class 'B' bricks laid flat , length of bricks across the route of underground cable all as specified and directed by Engineer-in-Charge.

Supplying, laying, jointing and testing and commissioning 35 sqmm, 3.5 core XLPE insulated, screened, PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded aluminium conductor & PVC sheathed LT cable 1100 volts grade conforming to IS-7098 laid in trenches/ ducts/ fixed on poles/wall/laid under roads/paths/drain/culverts or passing through pipes complete all as specified and directed by Engineer-in-Charge. Note :Excavation, earth work, sand cushioning and brick protection required for item shall be measured and paid separately under respective items

S&F Distribution board double door made out of CRCA mild steel sheet surface with insulated material like polyester or with powder coating surface mounting TPN 4 way 415 volts with bus bar rating 200 Amps dust and vermin proof suitable for incorporation of MCCB's and isolators etc complete all as specified and directed..

S & F of MCCB suitable for 415 volts AC supply, TPN with over load and short circuit protection and rupturing capacity not less than 16 KA and 63 Amps all as specified and directed.

S&F Distribution board double door made out of CRCA mild steel sheet surface with insulated material like polyester or with powder coating surface mounting SPN 12 way 240 volts with bus bar rating 200 Amps dust and vermin proof suitable for incorporation of MCB's and isolators etc complete all as specified and directed..

S&F Distribution board double door made out of CRCA mild steel sheet surface with insulated material like polyester or with powder coating surface mounting SPN 8 way 240 volts with bus bar rating 200 Amps dust and vermin proof suitable for incorporation of MCB's and isolators etc complete all as specified and directed..

S & F of MCB suitable for 240 volts AC supply, SPN with over load and short circuit protection and rupturing capacity not less than 10 KA and 40 Amps all as specified and directed.

S & F of MCB suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA and 6 to 32 Amps all as specified and directed.

M & L for Sub main wiring with 2 single core 6 Sqmm PVC insulated FRLS cable with multicore copper conductor drawn into and including PVC conduit rigid non metallic of suitable dia with and including independent PVC insulated one run 4 Sqmm single core copper earth wire complete all as specified. (Note:- Three lengths of 6 sqmm cable and will be measured as one length).

M & L for Sub main wiring with 2 single core 4 Sqmm PVC insulated FRLS cable with multicore copper conductor drawn into and including PVC conduit rigid non metallic of suitable dia with and including independent PVC insulated one run 6 Sqmm single core copper earth wire complete all as specified. (Note:- Three lengths of 6 sqmm cable and will be measured as one length).

Earthing complete with galvanised steel earth platge electroe 60 cmx60cm6mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below normal round level) with edge of the plae not less than 1.5 mtr below normal ground level, connected to galvanized earth lead wire 4mm dia by means of bolts, nuts, check nuts and GI washers earth plate shall be surrounded by alternate layer of charcoal or coke and common salt 15cm thick all around bottom and top of earth plate as shown in electrical piate No. 3 of SSR Part-I and connecting to earthing test point and testing on completion including PCC 1:3:6 type C2 for earthing pit, GI light grade protection pipe of size 15mm dia, watering pipe 20mm bore medium grade, CI cover and frame necessary earth works and PCC work etc complete all as specified. Earth plate shall be surrounded by alternate layer of charcoal of coke and common salt 15cm thick alround the earth plate including bottom and top. (Note: PCC chamber shall be constructed at least 1.5mtr away from the earth electrod and pipe for watering shall be slanting manner)

G S CONSTRUCTIONS

KATARIA CONSTRUCTION

SHRI RAM TRADING CO.

A R CONSTRUCTION COMPANY