ETP and Construction of Drain

Civil Work

Demolishing cement concrete 1:4:8 or leaner mix manually/ by mechanical means including disposal of material within 50 metres lead.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres.

Demolishing brick work In cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Disposal of malba to dumping ground within 10 km lead i/c loading, unloading etc. complete km lead

E/W; foundation trenches drains; not exceeding 1.5 m width or 10sqm on Plan….all kinds of soil

E/W;over areas; exceeding 30cm depth, 1.5 m width, 10 sqm on plan….All kinds of soil

Extra for additional lift of 1.5 m or part thereof..Ordinary or hard rock Extra 1.5 to 3.0 Mtr 252.30+90.40=342.70

Extra 3.0 to 4.5 Mtr 342.70+90.40=433.10

Extra 4.5 to 5.5 Mtr 433.10+90.40=523.50

Extra 1.5 to 3.0 Mtr for drain 181.85+90.40=272.25

E/W; Surface Excavation not exceeding 30 cm depth,1.5m width,10 sqm on plan…..All kinds of soil

P/L Cement Conc. 1:2:4 (Coarse sand (zone-III), 20 mm St.aggregate) in footings etc.

P/L Cement Conc. 1:4:8 (Coarse sand (zone-III), 40 mm St.aggregate) in footings etc.

P/L design mix concrete M-25 grade using cement 330 kg/cum i/c pumping of concrete, admixture; excluding centring shuttering & reinforcement ; All works upto plinth level

P/L design mix concrete M-25 grade using cement 330 kg/cum i/c pumping of concrete, admixture; excluding centring shuttering & reinforcement ; All works above plinth level upto floor V level

Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum).

RCC 1:1.5:3 (cement: coarse sand (zone-III): st. agg. 20 mm);All works upto plinth level

RCC 1:1½:3 (cement: coarse sand (zone-III): st. agg. 20 mm) ; Lintels, beams, suspended floor, roof, chajja etc.

RCC 1:1.5:3 (cement: coarse sand (zone-III): st. agg. 20 mm);Walls, columns etc.

Precast RCC 1:1½:3 (cement: coarse sand (zone-III): st. agg. 20 mm) i/c 6 mm cement plaster 1:3 (cement: fine sand (zone-III)) on exposed surfaces and hoisting etc.; string courses bands copings bed plate anchor blocks plain window sills and the like

Centring shuttering ; foundation footing and bases for columns etc. mass concrete and precast shelves.

Centring shuttering ; walls, plinth and string courses etc.

Centring shuttering ;suspended floors, roofs landings, balconies and access plateform.

Centring shuttering; lintel beams etc.

Reinforcement for R.C.C ; Thermo mechanically treated bars.

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat---as required.: In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Structural steel work in single section --- and applying a priming coat of approved steel primer all complete.

6 mm cement plaster 1:3 (1 cement: 3 fine sand) finished with a floating coat of neat cement.

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard,on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).: Ordinary cement without any pigment.

Stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc. including welding, grinding, buffing----i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc.

Dry stone pitching 22.5 cm thick including supply of stones and preparing surface complete.

50 mm nominal dia. Chlorinated Polyvinyl Chloride (CPVC) Pipes.External work

Finishing walls with water proofing cement paint: New work (Two or more coats applied @ 3.84 kg/10 sqm).

6 mm cement plaster 1:3 (cement : fine sand)

Cement plaster skirting (up to 30 cm height) with cement mortar 1:3 (1 cement : 3 coarse sand): 18 mm thick.

External Electric Supply Supply, installation, testing and commissioning of silent type DG sets, AMF Panel, bus ducting / cables from DG sets to essential panel, synchronizing panel where required, DG set elclosure room sound insulation/ventilation/smoke exhaust as required, earthing of DG set system, control cabling, fuel tank/piping, DG set exhaust piping/Exhaust chimney as per CPCB norms, civil works connected with DG Sets including foundation as required of capacity 62.5 KVA Supply of XLPE insulated PVC sheathed Al. conductor armored cable for working voltage upto 1.1 KV grade confirming to IS-7098 (Part-I) 1998 as required.

Supply of XLPE insulated PVC sheathed Al. conductor armored cable for working voltage upto 1.1 KV grade confirming to IS-7098 (Part-I) 1998 as required. 3.5 core 50 sqmm

Earthing with G.I earth plate 600 mm X 600 mm X 6 mm thick including acessories and providing masonry enclosure with cover plate havong locking arrangement and watering pipe of 2.7 metre long etc. with Charcoal/coke and salt as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt) as required

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Upto 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required above 35 Sqmm Upto 95 Sq.mm.

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size in the existing masonry openduct as required Upto 35sqm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required above 35 Sqmm Upto 95 Sq.mm.

Supplying and laying of following size DWC HDPE pipe lSI marked along with al accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. complete as required.63 mm dia (OD-63 mm & ID-51 mm nominal)

Supplying and laying of following size DWC HDPE pipe lSI marked along with al accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. complete as required.63 mm dia (OD-90 mm & ID-76 mm nominal)

Supply of XLPE insulated PVC sheathed Al. Conductor Armoured Cable 1.1KV grade conforming to IS-7098 of following size: -2C*10 sqmm

Installation and commissioning of street light/Flood Light etc as required

Supply of 140 watt LED Street Light/Flood Light Luminaire fitted with lens made of pressure die cast aluminium housing and toughened glass cover complete with the following specifications as per relevant IS (a) Total System Wattage: 140 Watt +5% (b) Luminaire Efficacy -130 Lumens/watt minimum (c) Power factor & amp;amp;gt;0.95 (d) Protection Class IP66 (e) LED Package shall be Ceramic Base. (f) Multi Chip. Array, Multi Die, Mld Power, Integrated Arrays and COB type Chip are not permitted (g) Operating Current of LED < 70% of rated maximum forward current, limited to a minimum of 350 mA and maximum of 1000 MA. (h) Wattage of LED Package: One watt to Five watt maximum (i) CRI >70 (j) THD<10% for complete fixture (k) Operating Voltage-110-320 V, 50Hz +/- 3%. (l) The driver must have thermal Protection against 75 deg C ambient temperature with Internal SPD of minimum 6 KV. Separate Compartment for Driver (m) Life of Street Light: Minimum 50,000 hrs

Supply and fabrication of pole protection system made up of 8 SWG steel wire mesh of size 25mmx75mm rectangular with 50mmx50mmx6mm MS angle Iron for supporting the mesh and grounding the protection system in suitable quality of CC etc as reqd.

Providing and fiixing M.V. danger notice plate of 200 mmX 150 mm X, made of mild steel, at least 2 mm thick , and vitreous enamled white on both sides, and with inspection in single red colour on front side as required

Fabrication, Supplying, Installation, testing, Commissioning of 12 mtr. high mast System with its accessories, Mast shaft shall be in one section, hot dip galvanized 4mm thick (Single dip) inside & out sides &suitable for wind velocity as per IS 875 part3 .There shall be in longitudinal seam weld per section and No circumfrential weld. It should also included accessories For High Mast head frame ,2 point suspension system with steel wire rope 5mm dia. (7/19construction) single drum winch ,galvanized lantern carriage arrangement suitable for 4/6 Nos. Flood Light luminaries symmetrically and its control gears boxes and lighting finial ,the mast shall have integral type manual tool mounted at the base compartment of its raising and lowering operation with foundation bolts and Anchor plate and control panel housing suitable RCC (1:2:4) shallow foundation of size 1m(L) x 1m wide and 2m deep i/c excavation of earth, providing cutting, bending and placing in position, reinforcement of cold twisted bars of 12 mm dia -2100mm long (approx.) - 16 nos.and reinforcement of cold twisted bar of 8 mm dia - 3700 mm (approx.) - 13 nos. (with 150 mm spacing) as required with positioning of foundation bolts and providing DWC HDPE pipe for cable entry & exit as required for the high mast considering The safe soil bearing capacity at site as 10T/sqm at 2mts. Depth with all material i/c 4Nos S.P MCB,63Amp.DPIsolator etc as reqd. Logo/Name of manufacturer shall be embossed on the pole. Galvanization as per relevant IS.

Internal Electrification wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with modular switch, modular plate ,suitable G.I box and earthing the point with 1.5 sqmm. FLRC PVC insulated copper conductor single core cable etc as reqd. Group C

Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or in recess,including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing following piano type switch/socket on the existing switch box/ cover including connections etc. as required b) 3 pin 5/6 A socket outlet

Supplying and fixing following piano type switch/socket on the existing switch box/ cover including connections etc. as required a) 5 A Switch

Wiring for circuit / submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduct as required (a) 2x2.5 sq. mm +1x2.5 sqmm earth wire.

(b) 2x4 sq. mm +1x4 sqmm earth wire.

(c) 2x6 sq. mm +1x6 sqmm earth wire.

SITC of metal clad, powder coated, compartmentalized cubical panel board as per CPWD electrical specifications including insulated aluminum bus bars, supports, interconnection, erection of switch gears with depth 30 cm to 60 cm and making provisions for termination of incoming/ outgoing cables/ bus ducting and making foundation etc as required. (Suitable for 400 Amp TP& N)

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way, Double door

Supply and fixing following rating, double pole 240 V, isolator in the existing MCB DB complete with connections, testing and Commissioning etc. as required. 63 A

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (Single Pole)

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. (A)100 Amp TPMCCB

(B)150 Amp TPMCCB

(C)200 Amp TPMCCB

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 amps c curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required

S/I/T/C of LED Tube type luminaire 20 Watt rating complete with polycarbonate housing batten integrated electronic driver prewired with high efficient LEDs with the following: (a) Total system wattage 20 watt +/- 5% (b ) Luminous efficacy lumens/watt =95 (c) Power Factor =0.95

SITC of wall mounted fan 400mm sweep rated voltage 220-230 AC rated frequency 50HZ speed 1280-1350 RPM with desired color

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374- 2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. Net Total 2.000each @2730.00/each 5/I/T/C of 3 Core, 4 Sqmm. Electrical wire for Air Conditioner

Supply of 15" (380 mm) sweep 1400 rpm exhaust fan heavy duty complete with shutter blades etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including acessories and providing masonry enclosure with cover plate havong locking arrangement and watering pipe of 2.7metre long etc. with Charcoal/coke and salt as required.

Provinding and fixing 25 mmX 5 mm copper strip on surface or in recess for connetions etc.as required.

Provding and fixing 6 SWG dia GI wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain wiring as required

Part C (Commissioning, O&M for 5 Year) Design, Supply, Installation, Testing and Commissioning of 2x500 KLD (Kilo Litres Per Day) Sewage Treatment Plant (STP) based on Open Technology with O&M for 5 Years

Please Enable Macros to View BoQ information