Interior fit out works in office area at Block C, 2nd and 3rd floor, Centrum, Mall, M.G. Road, Sultanpur, New Delhi

Name of Work : Interior fit out works in office area at Block C, 2nd & 3rd floor, Centrum, Mall, M.G. Road,

Sultanpur, New Delhi.

S.No. Sub-Head DSR Amount (in Rs.) NDSR Amount (in Rs.)

2 ELECTRICAL WORKS 51,88,532.04 64,92,735.87

3 AUDIO- VIDEO WORKS 0.00 86,57,165.90

4 Active & Passive Work 0.00 17,53,026.01

6 PLUMBING & FIREFIGHTING WORKS 21,15,339.05 15,96,461.99

7 CIVIL & INTERIOR WORKS 59,16,982.06 1,82,07,442.59

8 FURNITURE 1,05,80,062.53

GST multiplication Factor (DSR x 1.0633 ) 2,01,94,210.77

TOTAL i/c GST (A) 7,47,42,247.00

Digitally signed by AMIT

SINGH 17:17:39 IST

HVAC Works For Office for NEEPCO, New Delhi

1.0 VRF/VRV OUTDOOR UNIT

Unit Quantity Rate DSR Amount NDSR Amount

Supply Installation, Testing & Commissioning of modular

type Variable Refrigerant Flow/ Variable Refrigerant

Volume air cooled Outdoor units suitable for cooling and

heating, having all hermetically sealed inverter type Scroll

Compressor(s), minimum two compressors for above 14 HP

modules, microprocessor based Controller, top discharge

type condensing unit(s), with R410A Refrigerant, vibration

1.1 isolators, with suitable foundation etc. complete as Per HP 138.00 16,415.00 22,65,270.00

required.The unit shall deliver the rated capacity at AHRI

Conditions and work even at 50°C ambient temperature

without tripping.The unit shall be suitable to work on

400V+/-10%, 3 Phase, 50Hz AC power supply.The unit shall

be filled with first charge of the refrigerant and ready for

use as required.The COP at AHRI conditions shall not be

less than 3.1 and IEER not less than 6.5 .

2.0 INDOOR UNIT

Supply, installation, testing and commissioning of following

minimum capacity 4-wayflow VRV/ VRF Cassette Type

Indoor ceiling mounted unit equipped with synthetic

washable media pre-filter, fan section with low noise fan/

dynamically balanced blower, multi speed motor, coil

section with DX Copper coil, electronic expansion valve,

outer cabinet, drain pump, grill, necessary supports,

2 vibration isolation, cordless remote control etc., suitable

for operation on single phase 230V±10%, 50 HzAC supply,

complete, as required. The unit shall have automatic

force shut down provision in case of fire on receiving

signal from BMS System. The cooling capacity of indoor

unit will be at air inl et conditions of 27 Degree CD Band

19 Degree CWB temperature.

4-Way Cassette type

Digitally signed by AMIT

SINGH 17:17:39 IST

1.0 VRF/VRV OUTDOOR UNIT

Unit Quantity Rate DSR Amount NDSR Amount

3.0 REFRIGERANT PIPING

Supply,Installation,testingandcommissioningincludingvacc

umiazationandNitrogentestingoffollowingnominalsizesofsof

t/harddrawncopperrefrigerantpipingforVRV/VRFsystem,co

mpletewithfittings,withsuitableadjustableringtypehangersu

pports,jointing/brazingincludingaccessories,insulatedwithX

PLEClass-Otubularinsulation/withClass-

Oclosedcellelastometricnitrilerubbertubularsleevessections

ofspecifiedthicknessasgivenbelowforSuctionandLiquidlines,

allaccessoriesasperspecifications etc. as required :

34.9 mm O.D (wall Thickness-1.2 mm) (Insulation: 19 mm) Rmt 505.00 1,230.00

28.6 mm O.D (wall Thickness-1.0 mm) (insulation : 19 mm) Rmt 371.00 1,108.00

22.2 mm O.D (wall Thickness-1.0 mm) (insulation : 19 mm) Rmt 267.00 865.00

19.1 mm O.D (wall Thickness-1.0 mm) (insulation : 19 mm) Rmt 330.00 707.00

15.9 mm O.D (wall Thickness-1.0 mm) (insulation : 13 mm) Rmt 282.00 588.00

Supplying and installing of following size of perforated hot

dip galvanized G.I cable tray with perforations not more

than 17.5%, in convenient sections, joined with

4 connectors, suspended from ceiling with G.I suspenders

including bolts and nuts, etc. for carrying refrigerant pipe

in outdoor application as required.

4.1 MR1 450 mm width x 62.5 mm depth x 2 mm thickness Rmt 120.00 1,173.29 1,40,795.30

4.2 MR2 225mm width x 50 mm depth x 1.6 mm thickness Rmt 45.00 755.46 33,995.55

5 CONDENSATE DRAIN UPVC PIPE

Supply, installation, testing and commissioning of uPVC

Pipe ,complete with fittings, supports,U trap

arrangement,Clean Plug with 6mm nitrile insulation and

accessories as per specifications, drawings.

Digitally signed by AMIT

SINGH 17:17:39 IST

1.0 VRF/VRV OUTDOOR UNIT

Unit Quantity Rate DSR Amount NDSR Amount

6 MR7 Imported fittings Y-joints and headers etc. Nos 471.00 4,514.54 21,26,350.38

7 Control & Trasmission Wiring

MR8 Providing and fixing control cum transmission wiring of 2 Mtr 3,500.00 170.40

core x 1.0 sq. mm copper in suitable conduits between 5,96,409.71

indoor and outdoor unit.

8 MR9 SITC of 1.0 T split with rotary compressor of 5 Star rating Nos. 2.00 46,982.22

Inverter technology approved make make inclusive of 5

year warranty on compressor all complete. (Note- Indoor 93,964.43

and outdoor unit should have copper Condensor and

9 MR10 Timer for Split ac for Server Nos. 1.00 4,018.59 4,018.59

11 MS Standard for ODU

MR11 Providing and fixing MS Stand for ODU along with vibration Nos. 8.00 9,202.34

pad as per approved drawing.

Digitally signed by AMIT

SINGH 17:17:39 IST

SUMMARY OF BOQ FOR ELECTRICAL WORKS FOR OFFICE FOR NEEPCO, NEW DELHI

S.NO. SUB HEAD NDSR AMOUNT (Rs.) DSR AMOUNT (Rs.)

1 MAIN PANEL & DISTRIBUTION BOARD Rs. 7,46,663 Rs. -

2 CABELS / MAINS Rs. 4,43,982 Rs. 4,976

4 LIGHTING FIXTURES Rs. 9,75,846 Rs. 64,428

5 WIRING FOR DATA AND VOICE OUTLETS Rs. 4,22,176 Rs. 5,46,966

6 CABLE TRAY.& RACE WAY. Rs. 7,06,593 Rs. 1,13,520

7 ACCESS CONTROL SYSTEM Rs. 18,28,896 -

8 FIRE ALARM & PA SYSTEM Rs. - Rs. 16,58,988

9 UPS & INVERTER SYSTEM Rs. 6,86,889 Rs. -

10 CCTV System Rs. 5,21,957 Rs. 1,07,250

GRAND TOTAL Rs. 1,16,81,268

GRAND TOTAL Rs. 1,16,81,268

Digitally signed by AMIT

SINGH 17:17:39 IST

PROJECT - NEEPCO, NEW DELHI _ELECTRICAL WORKS ESTIMATED COST

DSR-2022 Description

S.No No. Unit Qty Rate MR Amount DSR Amount

1 MAIN PANEL & DISTRIBUTION BOARD

MR1 Supply,installation,testing and commissing of 3phase and neutral 415V 4 wire free standing

floor mounted indoor MV panel made out of 14 SWG sheet after seven tank process and

painting with epoxy powder coating MV electrical panel shall be dust and vermin proof

,hinged and locable doors.The panel shall consist of suitable rating TPN bus bar at the

rating of 0.8A /SQMM Supported by DMC/SMC insulator and color coded with heat

shrinkable sleeves. Metering shall be provided as specified .The panel shall have short

circuiting with standing capacity of minimum 36KA and consist of the switch gear as

mentioned below .The panel shall got fabricated from manufacturer with CPRI test

certificate .The panel shall be mounted on U channel including supply and fixing of the

same.(including Capacitor banks)

− 250 Amps 4P 36KA On Load change over switch. -1No.

− 250 Amps 4P 36KA MCCB. -1No.

− Spreaders-1Set.

− Extended Rotary Operating Mechanism.-1Set

− Digital V A F Meter with built in Selector Switch, CTs, CT shorting links, R/Y/B LED indicating

lamps and control SP MCBs.

Outgoing Section

− 63 Amps FP MCB_C curve -6Nos.

− 80 Amps FP MCCB -1No.

− 125Amps 4P25KA MCCB-3Nos.

− 8 Step Automatic Power Factor Correction Relay (Digital)_1 No

− 63 Amps TP MCB -3Nos.

Digitally signed by AMIT

SINGH 17:17:39 IST

DSR-2022 Description

S.No No. Unit Qty Rate MR Amount DSR Amount

− 32 Amps TP MCB -4No.

− 10 kVAR AC3 Duty Contactor with 220 V AC Coil_3 Nos

− 5 kVAR AC3 Duty Contactor with 220 V AC Coil_4 Nos

− ON / OFF LED Indicating Lamps _7Set

− Start / Stop Push Buttons_7Set

− A/M Selector Switch_1 No

− Control S/P MCB (2/4 A)_7 Nos

− Neutral Links_7 Nos

− Control Blocks_7 Nos

- Enclosure, 300A TPN 415V 50Hz Electrolytic grade AL conductor Busbar with 100% neutal&

Non adhesive PVC insulated heat shrinkable sleeves, Internal Wiring, Terminals, etc.as SET 2.00 2,47,174.43 4,94,348.87

1.2 DISTRIBUTION BOARDS.

Supply , installation ,testing and commissioning of 'MCB double door Distribution Boards

dust and vermin 'proof protected and AC supply operation including incoming

MCB/ELCB/RCBO/MCCB as per specifications and required capacity Neutral bar and Earth

Terminal complete as required and installed in concealed in wall after necessary chase

cutting with finishing /surface on wall including all fixing materials required.

20Way TPN MCB DB with 125A 4P MCCB(36KA) as incoming and 60 nos (6-32A)SP MCB as

outgoing.(For UPS DB)

16Way TPN MCB DB(Vertical type) with 80A 4P MCCB(25KA) as incoming and 48 nos (6-32A-

10KA )SP MCB as outgoing.(For LPDB)

12Way TPN MCB DB(Vertical type) with 63A 4P RCCBas incoming and 36 nos (6-32A-10KA )SP

MCB as outgoing.(ACDB)

8Way SPN MCB DB with 40A DP RCCBas incoming and 8 nos (16-20A-10KA )SP MCB as

outgoing.(For Server)

Total of Main Panel/ DB carried over to summary 7,46,663.47 0.00

3.0 CABELS / MAINS

Digitally signed by AMIT

SINGH 17:17:39 IST

DSR-2022 Description

S.No No. Unit Qty Rate MR Amount DSR Amount

Supply ,laying,testing and commissoning of 1100V grade armoured cable having sector /

circular shaped aluminium / copper conductor PVC insulated cores under ground PVC

tape wrapped inner sheathed, GI strip / wire armoured and overall extruded PVC sheathed

confirming to IS: 1554, laid on wall or ceiling using GI clamps and spacers as per route

shown at site and further as directed by Engineer-in charge

MR6 185 Sq.mm 3 1/2 core Aluminium cable mtr. 100.00 1,789.67 1,78,967.00

MR7 35 Sq.mm 3 1/2 core Aluminium cable mtr. 50.00 446.71 22,335.39

MR8 16 Sq.mm 4 core copper cable mtr. 50.00 317.02 15,851.13

MR9 25 Sq.mm 4 core copper cable mtr. 50.00 408.07 20,403.57

MR10 4 Sq.mm 3 core Copper cable mtr. 300.00 487.03 1,46,108.30

Supply & fixing of end termination for above mentioned cables including compressed type

3.1 brass glands, crimping type coper lugs, insulation tape etc. as 'required complete with

earthing of glands in following sizes

Total of Cables / Mains carried over to summary 4,43,982.33 4,976.00

Point wiring for light point /Fan/Exhaust Fan point/ call bell point using 2 runs of 1100 V

grade 1.5 sqmm & one run of 1.5 sq.mm FRLS insulated multistranded copper wires, in &

including 25 mm dia , MS conduit surface/ concealed in wall / ceiling conferming to IS 732

including all accessries such as junction boxes , conduit bends, elbows and ceiling rose ,

and anodised GI switch box with modular switch ,modular plate and the box covered with

a 1.3.3 One light point controlled by one 6A switch Per Pts 200.00 1,845.00 3,69,000.00

Secondary light point controlled by same switch

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC

4.2 1.7 insulated copper conductor, single core cable in surface/ recessed steel conduit as

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Per

2 X 4 sq. mm + 1 X 4 sq. mm earth wire Per

Digitally signed by AMIT

SINGH 17:17:39 IST

DSR-2022 Description

S.No No. Unit Qty Rate MR Amount DSR Amount

4.3 1.3.3 Exhaust fan point including of ceiling rose near fan. Per Pts 14.00 1,845.00 25,830.00

Wiring for twin control point wiring using 1.5 sqmm copper conductor FRLS PVC insulated

copper conductor cable drawn through 25 dia MS conduit laid in surface/concealed over

4.4 1.4 false ceiling or in slab/wall chases including ,2way modular switches,modular plate Per Pts 4.00 1,981.00 7,924.00

,suitable GI box and earthing the point with 1.5 sqm FRLS PVC insulated copper conductor

single core cable as required

Supplying and fixing following modular switch/ socket on the existing modular plate &

switch box including connections but excluding modular plate etc. as required.

c 1.24.4 3 pin 5/6 A socket outlet Each 10.00 122.00 1,220.00

d 1.24.5 6 pin 15/16 A socket outlet Each 30.00 197.00 5,910.00

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate

for modular switches in recess etc. as required.

Supplying and fixing following Modular base & cover plate on existing modular metal boxes

etc. as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE

4.8 1.19 insulated, shielded with fine tinned copper braid and protected with PVC sheath in the Meter 200.00 47.00 9,400.00

existing surface/ recessed steel/ PVC conduit as required.

4.9 MR14 Supplying and laying HDMI Cable with connector on both ends. Meter 100.00 315.58 31,557.94

1.20 Supply and fixing of following sizes of MS conduit along with accessories in surface /recess

4.10 including painting in case of surface conduit,or cutting the wall and making good the

same in case of recessed conduit as required

Supply and fixing of 3 nos. 6A socket with 6M modular GI box, base plate and cover plate

below worktop, along with 1no. 6A socket, 1 no. 6A switch and 1 no. 16A switch(for 3 nos.

sockets) in 4M modular GI box, base plate and cover plate above worktop complete as

per drawings and instructions of engineer in charge.

Supply and fixing of 2 nos. 6A socket with 6M modular GI box, base plate and cover plate

below worktop, along with 1no. 6A socket, 1 no. 6A switch and 1 no. 16A switch(for 2 nos.

sockets) in 4M modular GI box, base plate and cover plate above worktop complete as

per drawings and instructions of engineer in charge.

Total of Wiring carried over to summary 1,59,732.94 26,92,404.00

5 LIGHTING FIXTURES

Digitally signed by AMIT

SINGH 17:17:39 IST

DSR-2022 Description

S.No No. Unit Qty Rate MR Amount DSR Amount

SITC of 1'X4' recessed mounted Luminaire with Maximum 36 Watt with Lumen output of 3600

lumen. The product should be SMD based and have non integral isolated driver with 2KV

inbuilt surge protection. THD<10%, PF >0.9,Product should have life class of 50K burning hour

at L70 B50 parameter, Luminiare operating temp 0 D to 45D. Internal wiring should have

teflon coted multi strand wires and external wire should have PVC coated multistrand wires.

SITC of Recessed mouted PDC lowdepth(height should not be more than 35mm) downlights

with maximum 12 Watt with minimum 1320 lumen.The product should be SMD based &

have non integral isolated driver with 2KV inbuilt surge protection. THD<10%, PF

5.2 MR18 >0.9,Product should have life class of 50K burning hour at L70 B50 parameter, Luminiare Nos. 96.00 878.89 84,373.65

operating temp 0 D to 45D. Internal wiring should have teflon coted multi strand wires and

external wire should have PVC coated multistrand wires.

SITC of Extruded Aluminium surface mounted 36Watt, 4000 lumen LED batten with PC

Diffuser and Spring Steel Clamps for Surface Mounting arrangement. Driver THD<15%, PF

5.3 MR19 >0.9,with 2KV inbuilt surge protection. Internal wiring should have teflon coted multi strand Nos. 147.00 1,022.57 1,50,317.38

wires and external wire should have PVC coated multistrand wires.

Supply, Installation, Testing and Commisioning of Suspended /surface/Recessed type linear

Luminaire of size 72mm (N.S.), Linear ultra modular fixture made up of extruded aluminium

housing with luminare efficasy more than 100 LPW, CRI >80, CCT of 5700K. suitable for 220

V, 50 Hz, The luminare rated life (L70) >50000 Hours with High efficiency driver with inbuild

surge protection, over voltage protection, short circuit protection and operating at >0.95

.making suitable arrangement for fixing including connection with 3 x 1.5 sq.mm. The price

shall include all accessories including jointing kit for uniform continuous lines of light across

ceiling etc complete in all respect

Digitally signed by AMIT

SINGH 17:17:39 IST

DSR-2022 Description

S.No No. Unit Qty Rate MR Amount DSR Amount

Providing & Fixing Coverings (Ceiling & Wall) Made out of Polyester Kintted fabric Coated

with polyurethane (PU). The Fibric width 2m,3m,4.1m,&5.1m with Weight of 200gm/m^2.

thickness of 0.3mm. The appearance of fabric is Matl. smooth and uniform with blance

color and ligth transmission of 50%. The tear strength of fabric should be accordance to CH.

4.5daN; TR: 6.5 daN. The fire Railing should be accordance to B-S1, do. The febric should be

humidity ressistant and free of cercinogenic subtance (CMR) or volatile organic compounds

(VOC's). At lableing in accordance with the French decree no, 2011- 321, Oeko -Tex

standar100 certified. The fabric should be paintabe/printable with approved manufacturer

5.5 MR21 guidelines with 10-year manufacture guarantee. the Installation of fabric should be dry Sqm 5.20 12,247.98 63,689.52

installation 7done at room tamperature using CLIPSO PVC, ASB tension profiles P.CC/P-

C10QS/P-C11QS/P-CCB022/P-B1/P-CC1P. There are several lighting options available

including various LED options and fluorescent lighting. When Positioned properly. LED

Lighting modules provide an even light flow, casting no shadowns or hot spots. coverings

are used for a variety of aluminated applications, including but not limited to walls, ceiling,

lightboxs or wall frames. coverings can enhance your door with a variety of spacial effects

fiber optics or changinglights, or create a statement piece incorporating custom printing.

The cost of electrical cove light fixtures is included in the same.

Supplying,installation,testing an d commissioning of Passive Infrared(PIR) technology based

occupancy sensor having high preformance, non regulating programmable type, suitable

5.6 15.1 for connected load upto 10Amp , for mounting height up to 2.8 mtr and for 5 m diameter EACH 14.00 4,602.00 64,428.00

coverage area along with necessary fixing arrangements i/c programming at site etc.

complete as required.

Providing & Fixing Heavy Duty 4 Blade, 15" Exhuast Fan complete with all hardware and

connectors etc., as per the direction of the engineer In charge

Providing & Fixing of 7W - 10W cylindrical surface/ suspended light fixture having a minimum

5.8 MR23 of 630 lumens of dimensions - 35(L) x 20(w) x 20(h) mm as per the approval of the engineer each 76.00 2,197.32 1,66,996.46

Total of Light Fixture carried over to summary 9,75,846.21 64,428.00

6 WIRING FOR DATA AND VOICE OUTLETS

Supply and fixing the following sizes of PVC medium duty ISI marked conduits (IS : 9537 Part-

III) complete with accessories such as bends, junction boxes, pull boxes etc., in recess or on

surface including cutting chases in the walls/floors and making good the same complete as

Supplying and drawing of CAT 6A U/UTP cable, white jacket, 4 pair LAN Cable in the existing

surface/ recessed Steel/ PVC conduit as required.

Digitally signed by AMIT

SINGH 17:17:39 IST

DSR-2022 Description

S.No No. Unit Qty Rate MR Amount DSR Amount

Supply & fixing of Plug in type information outlet (campatible with data cables) in existing

faceplate/ GI Box in wall/furniture/floor complete as required.

Supplying and fixing following modular switch/ socket on the existing modular plate &

switch box including connections but excluding modular plate etc. as required.

a 1.24.6 Telephone socket outlet Each 60.00 148.00 8,880.00

7.5 Supply and fixing of the following types Face Plates complete with all accessories.

Supply & Fixing of Single Faceplate, Single Port square plate having spring shuttered front

a MR25 access for preventing ingress of dust, dimension as per commercially available modular Nos. 10.00 92.45 924.48

office furniture.

Supply & Fixing of Dual Faceplate, Duplex Port (for data and for voice) or as required

b. MR26 square plate having spring shuttered front access for preventing ingress of dust, dimension Nos. 100.00 92.45 9,244.77

as per commercially available modular office furniture.

Supply ,laying ,installing , testing and commmissioning of the 50 pair multi core 0.61 mm

annealed copper conductor PVC insulated and PVC sheathed armoured telephone cables

7.6 MR27 generally conforming to ITD S/WS-11-C and IS 1554 part I direct in ground /surface and / or mtr. 200.00 470.37 94,074.48

in existing pipe as required and includig making terminal joints, complete as required.

Supplying, installing, testing and commissioning of 24 port Cat 6A patch panels available

with block of four equipped with tool less IO, Rack Mountable. 19" Modular Patch Panel,

loaded CAT6A U/UTP 24 port LCS2 rack mountable to be compatible in 4nos of 6 X RJ 45

Tool less connector U/UTP unit in a block.

Supplying, installing, testing and commissioning of Cabinet. Size 24U (800 X 800 mm) (WXD)

following accessories, Width (mm) 800, Depth (mm) 800, Approx.Net Wt (kg) 75, CRCA 'D'

Grade thickness (mm) 1.2, RAL 9017(Matt Black), Glass: 4mm Toughened Tinted Glass

Door,Injected one piece polyurethane gasket on frame, Accessories: Cooling Fan (230V

A/C 90 CFM) - 4 Nos, Cable Manager Metal- 4 Nos,PDU 230VAC - 1 No (12 nos. 6A/16A

sockets with plugs 6A/16A - 1/1pc & MCB 16A/32A -0/1 Pc), cable channel 100mm wide 24U-

2 Nos,Heavy Duty Stationary shelf M6 screws,washer,cage nuts (nickel coated))3 Nos.

Earthling Strips 150mm H - 1 No, Door Lock - 1 No, Castor Wheels (with Brake) - 2 Nos, Castor

Wheels (without Brake) - 2 Nos, Front Metal Band - 1 No. Packing: 5 ply cardboard & Inside

28 ply EP foam. In the rack there must be maintained 1 U = 1.75 inches space. Nos. 1 etc

complete as required

Total of Data & Voice carried over to summary 4,22,175.93 5,46,966.04

8 CABLE TRAY.& RACE WAY.

Digitally signed by AMIT

SINGH 17:17:39 IST

DSR-2022 Description

S.No No. Unit Qty Rate MR Amount DSR Amount

Supply, fabrication and fixing of steel frame work in position for cable tray/Panels

fabricated out of 10 mm dia GI rods, ISA-40 MS angle iron, ISMC-50 channels, flats

etc.complete with providing of Anchor fastners and all necessary hardwares as required for

fixing, including cutting, bending, welding, drilling, bolting etc. as per design as required

and painted with one coat of primer and two coats of enamel paint of approved shade.

Supply and fixing of Perforated type 2mm thick Hot dip Galvanised G.I. cable tray of

following sizes complete with bend/tee joints, coupling plate & nuts bolts etc. as required

for fixing and including the cost of providing loop earthing with 2 nos. 50 mm x 6 mm GI

earth strips complete as per specifications, as required and as below.

8.2 GI Raceway & Junction boxes ( Raceway on floor shall be of aluminium only)

Providing and fixing 2 mm thick steel sheet factory fabricated post galvanized raceway

with internal partition/compartmentized of the following sizes including providing

removable 3 mm thick GI cover, knock out holes and fixing accessories earthing with 8 SWG

copper earth wire complete as required including floor supports, bends, access boxes, tap

off boxes and cross over as per specification and site requirement. (overhead / wall

mounted recovery & function boxes shall be 1.6 mm thick)

a) MR30 300 mm wide x 38 mm deep raceway RM 65.00 2,575.71 1,67,421.44

b) MR31 225 mm wide x 38 mm deep raceway RM 50.00 2,123.63 1,06,181.51

c) MR32 150 mm wide x 38 mm deep raceway RM 140.00 1,647.15 2,30,601.55

MR33 Providing and fixing 350 x 350 x 60 mm deep 2 mm thick GI sheet junction box including

providing 3 mm thick stainless steel cover as per specification.

MR34 Providing and fixing 150 x 150 x 60 mm deep 1.6 mm thick GI sheet junction box including

providing 3 mm thick stainless steel cover as per specification.

Total of Raceway carried over to summary 7,06,592.90 1,13,520.00

Digitally signed by AMIT

SINGH 17:17:39 IST

ESTIMATED COST FOR ACCESS CONTROL SYSTEM

11 ACCESS CONTROL SYSTEM Unit Qty Rate Amount

Supply, Installation,Testing and commisioning of Contact less Face Recognition and

RFID based Access terminal, RFID Supported (125kHz EM & 13.56MHz MIFARE, MIFARE

Plus, DESFire/EV1, FeliCa), Mobile Card (NFC/BLE), 30,000 (1:1 User based), 5 Faces/

User Capacity, 5,000,000 Text Logs, 2" TFT Screen, 24 bit Voice DSP with ECO

Cancillation, Eternet, RS 485, Weigand Supported, Complete as Required.

Supply, Installation, Testing & Commissioning of 2 Door/ 2 Reader IP Controller

2 accommodates a card database of 55,000 cards, and a transaction buffer of 45,000 Nos. 10 62,950.63 6,29,506.25

transactions,TCP/IP, USB, Serial Interface unit, Relay Switching Port.

3 Supply, Installation, Testing & Commissioning of Proximity Cards. Nos. 250 331.57 82,893.23

Supply, Installation, Testing & Commissioning of Electromagnetic Lock 600 lbs, single

4 leaf, LED Status Display, includes Door Sensor, i/c making conection, integration, Nos. 10 2,988.68 29,886.78

testing etc. complete as required on site

Supply, Installation, Testing & Commissioning of Power Supply 12V 2 A for Access

Control Reader and Door Lock Unit, Complete in all respect as required at site.

Supply, Installation, Testing & Commissioning of Alagtech U/L Clamp made of

6 aluminium anodised for EM Lock on the surface of frame/structure etc. i/c alignment Nos. 10 1,373.39 13,733.87

etc. for smooth operation of EM lock etc.

Supply, Installation, Testing & Commissioning of 24 Port Gigabit Switch, Auto MDI-MDIX

7 for all port,Link Status Detection, 4.8 Gbps Switching Capacity, Rack Mountable, Nos. 1 38,420.26 38,420.26

Complete in all Respect as required at site.

Supply, Installation, Testing & Commissioning of Access Control Software for with

Advance Access Management Module & Advance Attandence Mangement

Module. It should support Multi company, Multi location, Multi department, Multi login

with different rights, Muti hierarchy of employee.

Total of Access Control System carried over to summary 18,28,895.56

Digitally signed by AMIT

SINGH 17:17:39 IST

ESTIMATED COST FOR FA & PA SYSTEM

A. SITC OF FIRE ALARM SYSTEM & ACCESSORIES : MR. DSR.

Sr. No Description Unit Qty Unit Rate Total amount

Sr. No Description Unit Qty Unit Rate Total amount

2022.No. amount

Supplying, installation, testing and commissioning of micro

processor based intelligent addressable main fire alarm

panel, central processing unit with the following loop

modules and capable of supporting not less than 240 devices

(including detectors) and minimum 120 detectors per loop

and loop length up to 2 km, network communication card,

minimum 320 character graphics/ LCD display with touch

screen or other keypad and minimum 4000 events history log

in the non volatile memory (EPROM), power supply unit (230

1 17.2.1 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed

maintenance free batteries with automatic charger. The

panel shall have facility to connect printer to printout log and

facility to have seamless integration with analog/digital voice

evacuation system (which is part of the schedule of work

under SH: PA System) and shall be complete with all

accessories . The panel shall be compatible for IBMS system

with open protocol BACnet/ Modbus over IP complete as per

specifications.

Supplying, installation, testing & commissioning of intelligent analog Pcs 84 2,858.00

2 17.2.4 addressable photothermal detector complete with mounting base 2,40,072.00

complete as required.

Supplying, installation, testing & commissioning of intelligent addressable Pcs 1 2,726.00

3 17.2.9 thermal detector with rate of rise cum fixed tempreature thermistor 2,726.00

complete with base as required.

Supplying, installation, testing & commissioning of addressable manual call Pcs 4 3,871.00

point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum Pcs 4 3,506.00

strobe complete as required.

Supplying, installation, testing & commissioning of fault isolator complete Pcs 4 3,270.00

with base as required.

Supplying, installation, testing & commissioning of response indicator on Pcs 4 276.00

7 17.2.5 surface/recessed MS Box having two LED, metallic cover complete with all 1,104.00

connections etc as required.

B CABLES & ACCESSORIES FOR FAS :

Digitally signed by AMIT

SINGH 17:17:39 IST

Sr. No Description Unit Qty Unit Rate Total amount

Sr. No Description Unit Qty Unit Rate Total amount

2022.No. amount

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, RM 650 173.00

600/1000V rated with annealed copper conductor having

XLPE insulation, steel wire armouring & FRLS outer sheath

complete as required.

C SITC OF PUBLIC ADDRESSABLE SYSTEM & ACCESSORIES :

Supplying, installation, testing & commissioning of 6 zone, Pcs 2 1,26,411.00

voice alarm controller with USB, MP3 player (including 6 zone

1 17.3.1 button paging station) with seamless integration facility with 2,52,822.00

main fire alarm panel for voice evacuation complete as

Supplying, installation, testing & commissioning of digital Pcs 4 96,779.00

2 17.3.6 audio amplifier 50 Watt, 25V rms operating at 240 volt AC 3,87,116.00

supply complete as required.

Supplying, installation, testing & commissioning of Pcs 45 2,428.00

3 17.3.4 ceiling/wall mounted loud speaker, 3/1.5 Watt in ABS 1,09,260.00

enclosure complete as required.

D CABLE & ACCESSORIES FOR PA SYSTEM

Supplying and drawing of cable Fire Retardant PVC insulated

copper conductor cable in the existing surface / recessed

steel conduit of following pairs, cores and size including

connections and interconnections etc. as required..

17.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm RM 600 54.00 32,400.00

GRAND TOTAL Rs. 16,58,988.00

GRAND TOTAL Rs. 16,58,988.00

Digitally signed by AMIT

SINGH 17:17:39 IST

Sr. No 2018. Description Unit Qty Unit Rate DSR Total amount

Sr. No 2018. Description Unit Qty Unit Rate DSR Total amount

7 IP BASED CCTV SYSTEM

7.1 Supply and fixing of following sizes of MS conduit along with accessories in surface

/recess including painting in case of surface conduit,or cutting the wall and

making good the same in case of recessed conduit as required

7.2 Supply, installation, testing and commissioning of 2MP 2.8mm/3.6mm wide angle

fixed lens IR Dome Camera 1/3" Progressive Scan CMOS;

H.265+/H.265/H.264+/H.264/MJPEG; Colour: 0.01 lux @(F1.2, AGC ON), 0 lux with IR;

25fps/30fps(2560×1440, 1920×1080); 3 VCA functions; 3 streams; 3D DNR; ICR; EXIR

2.0, up to 30m; DC12V&PoE; Built-in micro SD/SDHC/SDXC slot.

7.4 Supply, installation testing and commissioning of Network Video recorder Linux

based to manage and control all the cameras from control room. Software shall

MR2 support maximum 32 channel with joystick controller. 256Mbps Bit Rate Input

Max(up to 32-ch IP video), 4 SATA Interfaces, alarm I/O: 16/4, 1.5U case,19" with

4x6TB i.e. 24TB HDD inside Nos. 1 Rs. 1,28,444 Rs. 1,28,444

7.6 Supply, installation, testing and commissioning of Video Management software

enabling security related personnel to easily and remotely gather video evidence,

monitor live situations, and configure and maintain a video surveillance system over

Ethernet consisting of digital video recorders (DVRs), hybrid digital video recorders,

network video recorders (NVRs), analogue video cameras, and IP video cameras

should support Detachable Viewers –users have the ability to detach Viewer panels

and move them to other (or the same) monitor(s). A maximum of two (2) Viewers

can be detached for a total of 75-up video tiles [two (2) detached and one (1)

7.7 Supply Installation Testing & Commissioning of 21 inch Full HD LED monitor including

wall mount brackets/ clamps/ desk mounting stand. Nos. 1 Rs. 6,072 Rs. 6,072

7.8 MR5 Supply and fixing of RJ45 Connector Nos. 26 Rs. 372.78 Rs. 9,692

7.9 Supplying and fixing in position GI box for data outlet suitable for fixing of RJ 45 face

plate complete as required. Nos. 26 Rs. 92.26 Rs. 2,399

Digitally signed by AMIT

SINGH 17:17:39 IST

Sr. No 2018. Description Unit Qty Unit Rate DSR Total amount

Sr. No 2018. Description Unit Qty Unit Rate DSR Total amount

7.10 Supply & Fixing of PCB based Information Outlet (I/O) RJ45, TIA-568C Category-6,

Termination of Catergory-6 UTP Cable, UL listed, Shall conform to Category-6 as per

the EIA/TIA-568C.2, Shall support network line speeds up to 1 Gbps, Shall have RJ-45

type connector with bend limiting and strain relief boot for securing IDC contacts

from external forces and for maintaining the bend radius of the cable, Shall have

minimum durability of 750 mating cycles and 200 termination cycles. Shall be

certified by independent labs like ETL/GHMT for compliance to EIA/TIA-568C.2. The

outlet shall be fixed in existing box & cover plate in wall/furniture/floor complete as

7.11 Supply & Fixing of Single Faceplate, Single Port (RJ45-DATA) square plate having

MR8 spring shuttered front access for preventing ingress of dust, dimension as per

commercially available modular office furniture. Nos. 26 Rs. 78.15 Rs. 2,032

7.13 Supply & Laying in existing conduits/raceway/furniture of 4-pair Unshielded twisted

pair cable with a cross filler (+), meeting Category 6 standards as per TIA-568C.2.

MR9 The cable shall be tested till 600 MHz or more from independent laboratories like ETL

for 4 connections. Test Certificate from independent labs like ETL shall be required.

7.14 Supply & Fixing of UTP Jack Panel UL listed, loaded with 24 no's UTP ports for PCB

based IO Jacks (RJ45, TIA-568C Category-6), having integrated bonding bar or

other mechanism for grounding, loaded with individually replaceable 24 nos.

Category-6 I/O Jacks complying with TIA-568.C.2. Shall be 6 port module

construction for better cable dressing at the rear. The jacks shall have RJ-45 type

connector with bend limiting and strain relief boot for securing IDC contacts from

external forces and for maintaining the bend radius of the cable.

7.15 Supplying & Fixing of Category 6, UTP patch cords constructed of 24 AWG

unshielded twisted pair stranded copper cable with an enhanced performance

modular plug at each end. Patch cord cable shall be offered in multiple coloured

UTP cable for design flexibility with a clear strain relief boot on each modular plug.

All patch cords shall be compatible with both T568A and T568B wiring schemes. UTP

Cable, 2 Meter. Nos. 26 Rs. 226.35 Rs. 5,885

Digitally signed by AMIT

SINGH 17:17:39 IST

Sr. No 2018. Description Unit Qty Unit Rate DSR Total amount

Sr. No 2018. Description Unit Qty Unit Rate DSR Total amount

7.16 Supplying & Fixing of Category 6, UTP patch cords constructed of 24 AWG

unshielded twisted pair stranded copper cable with an enhanced performance

modular plug at each end. Patch cord cable shall be offered in multiple coloured

UTP cable for design flexibility with a clear strain relief boot on each modular plug.

All patch cords shall be compatible with both T568A and T568B wiring schemes. UTP

Cable, 1 Meter. Nos. 26 Rs. 113.30 Rs. 2,946

7.17 Supply Installation Testing & Commissioning of Managed Layer -2 Switch with Power Nos

MR13 on Ethernet (PoE) enabled, 24 Port Fast Ethernet Web Smart Switch, including 2

Gigabit BASE-T and 2 Gigabit Combo BASE-T/SFP. 1 Rs. 12,833.30 Rs. 12,833

TOTAL OF IP BASED CCTV SYSTEM CARRIED OVER TO SUMMARY Rs. Rs. 5,21,957 Rs. 1,07,250

– 30 kVA UPS with 15 minute backup

Supply, unloading, shifting, installation, testing & commissioning of micro

processor controlled 30 kVA transformerless UPS , IGBT based rectifier to achieve

input THDI < 5% and input power factor of greater than 0.99 at 100% loading. True

Online Double Conversion (VFI as per IEC 62040-3) UPS using PWM IGBT technology

, 3 Phase input and 3 phase 415 V output UPS system; and comprising of the

following complete as required and as per specification:

Fully rated Rectifier cum charger unit and 100% rated Invertor unit

Integrated in UPS module.

Fully rated Inbuilt static switch at the inverter output and 100% rated Inbuilt

- static switch at the static bypass line integrated in UPS module.

Web-enabled Monitoring and Management through SNMP protocols for

multi-OS environments with below features.

Giving notifications like e-mail, paging notification, broadcast notification,

- battery replacement notification, run event-based scripts.

Event logging, data logging and action logging (with date, time,

description of fault and event).

Fully rated Inbuilt Maintenance Bypass Switch for the continuos operation

of the load during maintanance.

- Local notification through audible alarm.

Fully rated Battery Circuit Breaker with under voltage coil & deep

discharge protection to the batteries.

Digitally signed by AMIT

SINGH 17:17:39 IST

Sr. No 2018. Description Unit Qty Unit Rate DSR Total amount

Sr. No 2018. Description Unit Qty Unit Rate DSR Total amount

Battery Banks comprising of Valve Regulated Lead Acid Sealed

Maintenance Free batteries of minimum 5years design life to provide 15

minutes backup at 30 kVA ,0.9PF and ECV=1.7V with each UPS. The

batteries shall be installed on shelves of rack for quick replacement and

servicing. The temperature sensor shall be provided in the battery section

for temperature compensated charging. The bank of batteries shall

comprise of required numbers of batteries connected in series.

Vendor to provide complete details of make of Batteries, ampere hour

ratings, no. of Batteries, Expected life, Final discharge voltage, Nominal

float voltage, Battery recharge time & configuration of back up time,

Battery sizing Calculations

Supply, unloading, installation, testing & commissioning of open type MS

racks including top fully cover to protect from falling object to house SMF

batteries for 30 kVA UPS system along with suitable interconnecting links,

moulded case circuit breaker having Ithermal, Imagnetic & automatic U/V

trip mechanics for Battery Banks etc. complete as required & as per

specifications.

Supply, laying, testing & commissioning of flexible single core copper cable

for interconnections between UPS to UPS, UPS to batteries, complete as

required for 30 kVA UPS.

TOTAL OF UPS & INVERTER SYSTEM CARRIED OVER TO SUMMARY Rs. Rs. 6,86,889 Rs. -

Digitally signed by AMIT

SINGH 17:17:39 IST

S.No. Specifications Unit Qty Unit Price Amount

A Conference Room 3rd Floor

SITC of 100/98" smart 4K LED Display,Audio Built in Speaker(10W +

10W),HDMI 2.0 X 2, USB 2.0 x 1 , Audio Input X 1, OUTPUT Type Stereo

Mini Jack, HDMI X 1, Duty Cycle 24 x 7, Speacial features, File support

Direct vieweing of PPT, Word ,PDF, Images and video from pen drive,

EXTERNAL CONTROL RS232C(in) thru stereo jack, RJ45, OS Built in

android / windows /IOS , Brightness TYP300, Accessories=wall stand/

Table stand, Remote and standard cables

55" Full HD LED display, HDMI X 2, VGA X 1, Video IN X 1, USB X 1, Audio

2 IN X1, Audio Out X 1, SPDIF X 1, RS232C x 1, 20W in built speaker, IPS Nos 2 73,164.51 1,46,329.02

LED display, USB media player

SITC of Video Conference System for Virtual Meeting, minimum 12X

Optical Zoom Camera,

Supply, Installation, testing and commissioning of Ceiling Microphone tile

with 27 or more no. of omni directional microphone, Dante connectivity

: dual / redundant, POE enable (qty of microphone will vary as per the

mentioned coverage area and built in micorphone), Lighting Indication

4 on all four corner, It should work on open control protocol software and Nos 3 5,45,104.33 16,35,312.98

compitable to monitor with a single sofware for all the microphone in

the campus etc complete required as per the specifications.

Supply, Installation, testing, and commissioning of wireless digital

Boundary layer Microphone complete set with 18 or more channels (in

single transmitter & receiver set), RF output 100mW or more, cardioid

pickup pattern, Frequency range: 1880 to 1930 MHz, Connectivity: RJ-45,

Battery backup: 10 or more hr, etc and complete as required.

Supply, Installation, testing, and commissioning of wireless boundary

layer microphone wireless charging station from the same make, lighting

indication, etc complete required as per specifications.

Digitally signed by AMIT

SINGH 17:17:39 IST

S.No. Specifications Unit Qty Unit Price Amount

Supply, Installation, testing, and commissioning of digital signal

processor with 12no. input with AEC, USB and 8no. Output, Dante

(64X64), AES 67, Driver sample rate: 48kHz, OLED display, PoE

connectivity, BTU/Heat Load: 205 BTU/hr, EIN: <125dBu, THD+N:

0.002%, Processor Type: 40-bit floating point etc complete required as

per specifications.

Supply, Installation, testing and commissioning of quad channel

Amplifier, 4 X 120watt or more, THD+N (@ 1 kHz) : < 0.3%, Technology :

Class-D, Common mode rejection ratio : 70dB or better, Temperature

controlled FAN, Switching mode power supply, should have Protection

features like : DC Short circuit & Over heating & Over load & Signal

limiting etc, Built-in high pass filter and gain adjustment option etc

complete required as per specifications.

Supply, Installation, testing and commissioning of 6.5" two-way coaxial

thin edge ceiling loudspeaker, 100V transformer power taps : 24,12,6,

watts, Conical dispersion : 145° or more, impedance : 8, low impedance

9 RMS continous power : 30watts, frequency range : 50 Hz - 20 kHz or Nos 8 13,557.30 1,08,458.43

better, frequency response : 60Hz - 20KHz or better etc complete

required as per specifications.

Supply, Installation, testing and commissioning of Gigbit POE switcher , 8

port ethernet swtich

Supply, installation, testing and commissioning of of 2.5 Sqmm x 2 core

11 ATC copper Conductor, Insulated Cores,PVC Sheathed Speaker Cables . Rmt 250 164.24 41,059.26

Supply, installation, testing and commissioning of of Shielded twisted

pair CAT6 Cable (STP) complete etc as required 4 pair.

Supply, installation, testing and commissioning of of 35' 15–pin HD &

3.6mm Stereo Audio Cable

Supply, installation, testing and commissioning of of 12' 15–pin HD &

3.5mm Stereo Audio Cable

Supply, installation, testing and commissioning of of Various Connectors

15 For Above Mentioned Configuration etc. all complete. Lot 1 18,699.78 18,699.78

16 Supplying and laying HDMI Cable with connector on both ends. Rmt 50 701.88 35,094.05

Digitally signed by AMIT

SINGH 17:17:39 IST

S.No. Specifications Unit Qty Unit Price Amount

1X HDMI Type A female (Black), 100 Ω, 10.2Gbps (3.4 Gbps per lane),

340 MHz, HDMI (3D, Deep Color, 4K) HDCP2.2 Compatible Consumer

17 Electronics Control (CEC), Up to 4K @35m (Cat 5e/6) / 40m (Cat 6a/ATEN Nos 1 27,811.84 27,811.84

2L-2910 Cat6); 1080p@60m (Cat 5e/6) / 70m (Cat 6a/ATEN 2L-2910

Cat6)*4K Supported: Transmitter

1XHDMI Type A male (Black), 100Ω, 10.2 Gbps (3.4Gbps per lane), 340

MHz, HDMI (3D, Deep Color, 4K) HDCP2.2 Compatible Consumer

18 Electronics Control (CEC), Up to 4K @ 35m (Cat 5e/6) /40m (Cat6a/ATEN Nos 1 27,811.84 27,811.84

2L-2910 Cat6); 1080p@60m (Cat 5e/6) /70m (Cat 6a/ATEN 2L-2910

Cat6) *4K Supported: Recieve

SITC Wireless presentation system :Linux, 2160p60/30, 1080p60/30,

720p60, iOS, iPadOS, Android, Windows, macOS, Chrome OS , AirPlay,

Miracast (Peer-to-Peer and MICE), Chromecast, vSolution Cast, Max. no.

of on-screen window 4, GIF, JPEG, BMP, PNG, PDF, Word, PowerPoint,

Excel, Text, HTML, HDMI Out x1, Rear USB 3.0 x2, Front USB 3.0 x2, 1x

1GigE LAN port, - (HDMI In via third party USB frame grabber), Audio Via

19 HDMI out USB, 2.4 GHz in Access Point Mode / 2.4 and 5 GHz in Nos 1 2,19,724.39 2,19,724.39

Infrastructure Mode, TCP/IP, HTTP, HTTPS, SNTP/NTP, SSL, SSH, UDP,

DHCP, Static (IP address, Subnet mask, Default gateway, DNS server),

Proxy, Interface priority, IEEE 802.1X, WEP, WPA2, WPA2 Enterprise or

Cable cubby -SITC of cCable cubby -SITC of cable enclosure with tilt up lid

Multiregion power socket, , Pass through holes for HDMI, Audio, VGA

& LAN connectivity etc. as required Complete as per specification & as

20 required.able enclosure with tilt up lid Multiregion power socket, , Pass Nos 2 14,036.07 28,072.14

through holes for HDMI, Audio, VGA & LAN connectivity etc. as required

Complete as per specification & as required.

8 by 8 Matrix has the ability to connect up to eight 4K UHD HDMI sources

21 to up to eight 4K UHD HDMI displays and freely switch between them. Nos 1 4,20,750.54 4,20,750.54

B CMD & Meeting Room

Digitally signed by AMIT

SINGH 17:17:39 IST

S.No. Specifications Unit Qty Unit Price Amount

SITC of 75" smart 4K LED Display,Audio Built in Speaker(10W +

10W),HDMI 2.0 X 2, USB 2.0 x 1 , Audio Input X 1, OUTPUT Type Stereo

Mini Jack, HDMI X 1, Duty Cycle 24 x 7, Speacial features, File support

Direct vieweing of PPT, Word ,PDF, Images and video from pen drive,

EXTERNAL CONTROL RS232C(in) thru stereo jack, RJ45, OS Built in

android / windows /IOS , Brightness TYP300, Accessories=wall stand/

Table stand, Remote and standard cables

PTZ Camera, 12X Optical Zoom, Digital Zoom: Up to 12X Wide Viewing

Angle up to 72.5 Degrees, RJ-45 Port, Quiet Motor with Servo Algorithm

for PTZ Control, Full HD 1080p signal output format with a high frame

rate of 60 fps, HDMI, and USB 3.0 synchronous video outputs.

2.4 GHz Wireless Speakerphone, Built-in high-fidelity all-pointing

microphone offers 360 degree audio pickup, Full duplex Audio, Acoustic

Echo cancellation, Noise reduction removes ambient room

noise,Advanced DSP technology delivers remarkably rich, crystal-clear

audio,Immersive sound for calls, Wideband Frequency Response, 4

hours talk time ( Wireless),

Digitally signed by AMIT

SINGH 17:17:39 IST

Active & Passive Work

S.No Item Description Item Unit Qty Rate Amount

Supply, Installation, Testing & Commissioning of 48 x 10/100/1000BASE-T

PoE ports 4 x Gigabit GbE/SFP combo ports Advanced L2 switching and

security features L2+ Static Routing

Optional management user interface Full/Half-duplex for 10/100 Mbps Full-

duplex for 1000 Mbps 34.85 W/100 V 34.2 W/240 V IEEE 802.3 10BASE-T

1 Ethernet (twisted-pair copper) IEEE 802.3u 100BASE-TX Fast Ethernet 48-P Switch Nos 3.00 2,18,875.31 6,56,625.93

(twisted-pair copper) IEEE 802.3u 100BASE-FX 100 Mbps over fiber optic

IEEE 802.3ab 1000BASE-T Gigabit Ethernet (twisted- pair copper) IEEE 802.3z

1000BASE-X 1 Gbps over fiber optic IEEE 802.3az Energy Efficient Ethernet

(EEE) IEEE 802.3x Flow Control

48 x 10/100/1000BASE-T PoE ports 4 x Gigabit GbE/SFP combo ports

Advanced L2 switching and security features L2+ Static Routing

Optional “standard mode” or “surveillance mode” management user

interface 370W PoE budget, Full/Half-duplex for 10/100 Mbps Full-duplex

for 1000 Mbps 34.85 W/100 V 34.2 W/240 V IEEE 802.3 10BASE-T Ethernet

2 (twisted-pair copper) IEEE 802.3u 100BASE-TX Fast Ethernet (twisted-pair 48-P Poe Switch Nos 3.00 2,42,675.74 7,28,027.22

copper) IEEE 802.3u 100BASE-FX 100 Mbps over fiber optic IEEE 802.3ab

1000BASE-T Gigabit Ethernet (twisted- pair copper) IEEE 802.3z 1000BASE-X

1 Gbps over fiber optic IEEE 802.3az Energy Efficient Ethernet (EEE) IEEE

802.3x Flow Control

Supply, Installation, Testing & Commissioning of CAT 6A Patch Cord LSZH 1

Mtr, 4 pair 26 AWG stranded copper wire, Pre-terminated with RJ45 plugs,

3 Slim clear anti-snag slip on boots, Suitable for EIA 568A or 568B wiring, UL® Patch Cord 1mtr mtr 200.00 297.49 59,497.20

Listed, meets all TIA and ISO requirements. Complete in all respect as

required by site completion.

Digitally signed by AMIT

SINGH 17:17:39 IST

S.No Item Description Item Unit Qty Rate Amount

Supply, Installation, Testing & Commissioning of CAT 6A Patch Cord LSZH 2

Mtr, 4 pair 26 AWG stranded copper wire, Pre-terminated with RJ45 plugs,

Slim clear anti-snag slip on boots, Suitable for EIA 568A or 568B wiring, UL®

4 Patch Cord 2mtr mtr 200.00 339.32 67,863.99

Listed, meets all TIA and ISO requirements. Complete in all respect as

required by site completion.

SITC of 9U Networking Rack with Acessories (Fan, PDU, Castor, Cable

5 Manager, Mounting Hardware) for field switches complete as required. Rack 9U Nos 1.00 12,750.06 12,750.06

Supply, Installation, Testing and Commissioning of 42 U Networking Rack

(600*800), Front Glass Door Unit and Grilled back door unit, lockable Door

unit, Load Rating of Min 450 Kg. Pillar of frame must be aluminum and Rest

plated are steel, Powder Coated Rack with Castors (4nos.), Fan (4 Nos.),

Cable Manager (2Nos), Full Tray Unit (1 Nos.), PDU (1Nos.) complete in all

respect as required.

Supply, Installation, Testing & Commissioning of CAT 6A Infornmation

Outlet,Universal label permits T568A or B wiring, UL® Listed, meets all TIA

and ISO requirements.Complete in all respect as required by the site.

1U PVC Cable Manager is Ideal for Networking and Server Rack for the

8 Cable Manager Nos 10.00 297.49 2,974.86

better and effective management of cables

Supply, Installation, Testing & Commissioning of Fiber optic Mini GBIC

SFP Trans receiver 10G for network switch with Built-in spring latch for easy

module removal, Hot Swappable, Comply IFC and FDA Safety Standards

complete as required.

Digitally signed by AMIT

SINGH 17:17:39 IST

S.No Product Description Unit Rate Amount

Supply, Installation, Testing & Commissioning of Server based Communication System with

all the required Software licenses and Hardware - IP-PBX/IP Telephony Communications

Server: The IP Telephony Solution shall support the following Services - Voice, Video, IM,

Presence and Audio Conference The Solution should be built on Active-Active Redundant

Servers The IP Telephony Solution should support H.323 and SIP The Solution should support

the following Trunks - FXO, E1 PRI and SIP The IP Telephony solution should incorporate all

licenses for the Phones and Trunks Solution should support 80 Extensions from Day 1 with

future scalabilityupto 250 users. Licenses for all Phones supplied should be provisioned on

Day1 Solution should support Hard IP Phones, Analog Phones, Rack mount architecture,

complete as required and as per technical specifications.

SITC of Color display – 3.0 inches Touch Screen display , 4-position adjustable tilt display ,

Permanently-labeled feature buttons: speaker, mute, headset, contacts, home, H.323

protocol support history, message, phone, forwarding, volume (separate volume levels in

handset, speaker, ringer, and headset) Red LEDs on speaker, mute, headset, message and

2 history 24 administrative buttons Wideband speakerphone 0-5 Softkeys Ergonomic NOS 30 17,564 5,26,922.05

hearing aid compatible handset supporting TTD acoustic coupler Bluetooth and DECT

headset support with adapter Message waiting indicator Ethernet (10/100/1000) line

interface Secondary thernet (10/100/1000) line interface Optional IEEE PoE 802.3af

adapter registers as class 2 device,

2.0” (diagonal) color display—320 x 240 pixels, Multiple line phone with four red / green line /

feature indicators around display, 4 Context sensitive soft keys, Hard buttons for phone,

messages, contacts, history, home, navigation cluster, headset, speaker, volume, mute,

LEDs for speaker, mute, headset, essage, history, Wideband audio in handset and wired

headset, Full duplex speakerphone & handset, Ergonomic hearing aid compatible handset

supports TTD acoustic coupler, Message waiting indicator, Mute key with optional mute

alerting, IC call alerting with 360-degree visibility, Dual-position stand, optional wall-mount

3 stand, Gigabit Ethernet (10 / 100 / 1000) line interface, Second Ethernet interface 10 / 100 / 70 10,624 7,43,699.46

1000 Mbps, PoE Class (IEEE 802.3af) registers as class 1 device and supports 802.3az, Optional

AC to 5 volt power supply • SIP protocol support, Standards-based codec support: G.722,

Opus, Configurable via Web interface, Support for HTTPS, TLS and SRTP for encryption,

Recent Call Log (100 entries), Zero touch deployment via Device Enrollment Services

Support, Supports the following languages: Dutch, English (UK & US), French, (Canada),

French (France), German, Italian, Japanese, Portuguese (Brazil), Simplified Chinese, Spanish

(Latin America), Spanish (Spain),Traditional Chinese, Includ Licence.

Digitally signed by AMIT

SINGH 17:17:39 IST

Office for NEEPCO, New Delhi

BOQ FOR PLUMBING & FIRE FIGHTING

SECTION DESCRIPTION S.I (AMOUNT) N.S.I (AMOUNT)

A SANITARY FIXTURES & FITTINGS 11,66,966.52

B WATER SUPPLY 3,35,928.55 0.00

C INTERNAL DRAINAGE (SOIL, WASTE & VENT PIPES) 9,14,761.50 2,75,373.84

D FIRE FIGHTING 8,64,649.00 1,54,121.64

Total Cost ( Carried Forward) in Rs.

Digitally signed by AMIT

SINGH 17:17:39 IST

BOQ FOR PLUMBING & FIRE FIGHTING

SUB HEAD A: SANITARY FIXTURES & FITTINGS

SL. NO. DESCRIPTION OF ITEMS UNIT Qty DSR Rate (Rs.) NS Rate (Rs.) DSR Amount (Rs) NS Amount (Rs)

Providing & fixing glazed vitreous china single trap syphonic

pattern having back inlet ,supporting chair ,wall hung

water closet with cistern complete with all internal

fittings/accessories and CP brass flush bend (European type)

water closet with seat and lid, with C.P. brass hinges and

1.1 NS rubber buffers, adapter, rubber joints fixed to W.C., C.P.

brass screwed washers including cutting and making good

the walls and floors wherever required and HDPE wc pan

connector including jointing with white cement coomplete

in all respects

Wall hung W.C. pan (White colour)with white plastic seat &

lid "Thermoset moulded ( bakelite ) IS 2548 Part I

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 13 24,078.02 3,13,014.25

Providing & fixing glazed vitreous china wash basin with R.S.

or C.I. brackets painted white, 32mm C.P. brass waste of

standard pattern , C.P brass wall flange 32 mm dia. C.P.

brass bottle trap and union 32 mm dia C.P. pipes to wall

flange. complete including cutting and making good the

walls wherever required.

1.3.1 Undercounter wash basin (White colour)of size: 585x430 mm

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 13 8,384.52 1,08,998.82

1.3.2 NS Table top wash basin (white colour)of size: 440x440 mm

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 1 10,378.33 10,378.33

Providing & fixing 15mm C.P. brass single hole wash basin

1.4 NS mixer without popup waste system with 450mm long copper

pipes and brass nut

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 14 4,415.32 61,814.51

1.5 NS Providing & fixing vitreous chinaware urinal comprising

Large flat back wall hung urinal in glazed vitreous China

NS new magnum urinal

Digitally signed by AMIT

SINGH 17:17:39 IST

SL. NO. DESCRIPTION OF ITEMS UNIT Qty DSR Rate (Rs.) NS Rate (Rs.) DSR Amount (Rs) NS Amount (Rs)

15 mm electrically operated solenoid valve with infra red

sensor mounted in a box with SS Cover.

CP brass chromium plated flush piping from solenoid valve

to urinal terminated with a 15 mm screwed spreader

32 mm nominal bore CP cast brass waste

32 mm nominal bore CP cast bottle trap with extension pipe

rubber adopter for waste connection, CP brass wall flange.

For supply,installation,testing & commissioning of sanitary

fixtures(white colour) as per above details. Each 9 29,148.55 2,62,336.99

Providing & fixing stainless steel sink R.S. or C.I. brackets

painted, 40mm C.P. waste, C.P. brass chain and rubber

1.6 NS plug, 40mm C.P. cast brass bottle with necessary union

complete including cutting and making good the walls

wherever required

Stainless steel sink single bowl with drain board(size

510x1040mm) of approved

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 3 12,920.43 38,761.30

Providing & fixing Sink Mixer with Swinging Casted Spout

1.7 NS (Wall Mounted Model) with 450mm long Copper Pipes &

Brass Nuts.CP brass wall flange

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 3 5,270.60 15,811.81

Providing & fixing toilet paper holding including cutting and

1.8 NS making good the walls.

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 13 2,069.38 26,901.90

Providing & fixing Horizontal liquid soap dispenser with

1.9 NS stainless steel lid and brackets fixed to wooden cleats with

C.P. brass screws.

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 12 3,715.12 44,581.47

Providing & fixing C.P. brass coat hooks fixed on toilet door

1.10 NS with C.P. brass screws

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 13 628.10 8,165.33

Digitally signed by AMIT

SINGH 17:17:39 IST

SL. NO. DESCRIPTION OF ITEMS UNIT Qty DSR Rate (Rs.) NS Rate (Rs.) DSR Amount (Rs) NS Amount (Rs)

Providing & fixing beveled edge mirror 5.5mm thick of

superior quality plate glass complete with 6mm thick marine

1.11 NS ply sheet ground fixed to wooden cleats with CP brass

screws and washerswith 40 mm wide teak wood frame as

per design including polishing

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Sqm 13 2,897.65 37,669.44

1.12 NS Providing & fixing Hand Shower (Health Faucet) with 8mm

dia, 1M long PVC tube and wall hook CP brass wall flange

For supply of sanitary fixtures as per above details Each 13 1,796.26 23,351.43

Providing & fixing, testing and commissioning of storage type

electric water heater with automatic thermostatic control

electric element, pressure release valve, brackets fixed to

expansion fasteners with M.S. nuts and bolts all complete

including cutting and making good the walls wherever

3 litres capacity (Horizontal /Vertical type1.5 kw electrical

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 4 8,455.08 33,820.33

Providing & fixing wall mounted 25 mm dia Stainless steel

1.15 NS coated grab bar including cutting & making good the

walls(size 450mm long)

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 13 1,055.68 13,723.89

Providing & fixing 15 mm dia C.P. brass bib cock with Hose

union of approved quality.

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 14 1,428.53 19,999.43

Providing & fixing 15 mm dia C.P. brass bib cock with C.P.

wall flange of approved quality.

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 14 1,615.34 22,614.80

FRAGRANCE DISPENSER MACHINE :-Providing and fixing of

Fragrance Dispenser machine complete with refill can and

'C' size battery (2 Nos) for operation fixed to wooden cleats

with CP brass screws

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 12 4,708.15 56,497.78

Digitally signed by AMIT

SINGH 17:17:39 IST

SL. NO. DESCRIPTION OF ITEMS UNIT Qty DSR Rate (Rs.) NS Rate (Rs.) DSR Amount (Rs) NS Amount (Rs)

Providing and fixing of stainless steel finish Paper Towel

1.19 NS Dispenser having capacity of 300-350 paper towels fixed to

wooden cleats with C.P. brass screws

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 12 5,710.39 68,524.71

Detail of Sanitary fixture are for the information of the

Contractor,however model/makes of all sanitary fixtures

i. shall be selected by Architect/Interior designer/Project

manager and the same shall be binding for execution.

No additional fixing cost shall be paid for change in type of

sanitary fixtures.

Contractor to receive all the above mentioned items &

store at place as directed at site.

TOTAL CARRIED OVER TO SUMMARY 11,66,966.52

Digitally signed by AMIT

SINGH 17:17:39 IST

SUB HEAD B: WATER SUPPLY

DESCRIPTION OF ITEMS UNIT Qty DSR Rate (Rs.) NS Rate (Rs.) DSR Amount (Rs) Amount

Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes

having thermal stability for hot & cold water supply including all

(CPVC) plain & brass threaded fittings including fixing the pipe

18.7 with clamps at 1.00 m spacing. This including jointing of pipes &

fittings with one step CPVC solvent cement and testing of joints

complete as per direction of engineer in charge. .

Internal Work - Exposed on Wall

18.7.5 40 mm nominal outer dia pipes. Metre 30.00 674.35 20,230.50

Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes

having thermal stability for hot & cold water supply including all

CPVC plain & brass threaded fittings i/c fixing the pipe with

clamps at 1.00 m spacing. This including jointing of pipes &

fittings with one step CPVC solvent cement and the cost of

cutting chases and making good the the same including testing

of joints complete as per direction of engineer in charge.

Concealed work oncluding cutting chases and making good

18.8.2 20 mm nominal outer dia pipes. Metre 235.00 513.75 1,20,731.25

18.8.3 25 mm nominal dia Pipes Metre 144.00 626.05 90,151.20

18.8.4 32 mm nominal outer dia pipes. Metre 80.00 712.75 57,020.00

Providing and fixing brass stop cock of approved quality

Providing and fixing gun metal gate valve with C.I. wheel of

4 approved quality (screwed end):

18.17.1 25 mm nominal bore Each 8.00 532.35 4,258.80

18.17.2 32 mm nominal bore Each 8.00 589.90 4,719.20

18.17.3 40 mm nominal bore Each 8.00 707.30 5,658.40

Digitally signed by AMIT

SINGH 17:17:39 IST

DESCRIPTION OF ITEMS UNIT Qty DSR Rate (Rs.) NS Rate (Rs.) DSR Amount (Rs) Amount

Providing and fixing C.P. bass angle valve for basin mixer and

18.53 geyser points of approved quality conforming to I.S:8931 a) 15

5 mm nominal bore.

Providing and fixing unplasticised P.V.C connection pipe with

18.74 PTMT Nuts coller and bush of approved quality and colour.

18.74.2 15mm nominal bore with 45cm length Each 59.00 107.90 6,366.10

Sub-Total of Water Supply Installation, Separate for Scheduled & Non-Scheduled Items 3,35,928.55

Digitally signed by AMIT

SINGH 17:17:39 IST

SUB HEAD C: INTERNAL DRAINAGE (SOIL, WASTE & VENT PIPES)

SL. DSR - DSR Rate NS Rate DSR Amount NS Amount

DESCRIPTION OF ITEMS UNIT Qty

Providing and fixing cast iron trap of self cleansing design with cast

iron screwed down or hinged grating with or without vent arm

complete, including cost of cutting and making good the walls and

100 mm inlet and 100 mm outlet centrifugally cast (spun) iron S&S as

2 17.35 Providing and fixing soil, waste and vent pipes.

Centrifugally cast (spun) iron S&S pipe as per IS 3989.

17.35.1.2 100mm dia cast (spun) iron S&S pipe Metre 260 1,077.40 2,80,124.00

Centrifugally cast (spun) iron S&S pipe as per IS 3989.

17.35.2.2 75mm dia cast (spun) iron S&S pipe Metre 260 1,042.10 2,70,946.00

Providing and fixing single equal plain junction of reqd. degree with

access door, insertion rubber washer 3mm thick, bolts and nuts

3 17.43 complete.

17.43.1.2 Sand cast (spun) iron pipe IS-3989 Each 40 731.40 29,256.00

17.43.2.2 Sand cast (spun) iron pipe IS-3989 Each 12 573.80 6,885.60

Providing and fixing single equal plain junction of reqd. degree.

17.44.1.2 Sand cast (spun) iron pipe IS-3989 Each 22 707.30 15,560.60

17.44.2.2 Sand cast (spun) iron pipe IS-3989 Each 12 498.90 5,986.80

Providing and fixing bend of required degree with access door,

insertion rubber washer 3mm thick, bolts and nuts complete.

Digitally signed by AMIT

SINGH 17:17:39 IST

SL. DSR - DSR Rate NS Rate DSR Amount NS Amount

DESCRIPTION OF ITEMS UNIT Qty

17.38.1.2 Sand cast (spun) iron pipe S&S as per IS 3989. Each 12 597.60 7,171.20

17.38.2.2 Sand cast (spun) iron pipe S&S as per IS 3989. Each 12 453.40 5,440.80

6 17.39 Providing and fixing bend of required degree .

17.39.1.2 Sand cast (spun) iron pipe S&S as per IS 3989. Each 37 439.75 16,270.75

17.39.2.2 Sand cast (spun) iron pipe S&S as per IS 3989. Each 12 298.20 3,578.40

7 17.57 Providing and fixing collar.

17.57.1.2 Sand cast (spun) iron pipe S&S IS-3989 Each 13 439.75 5,716.75

17.57.2.2 Sand cast (spun) iron pipe S&S IS-3989 Each 12 271.45 3,257.40

Providing and fixing MS holder bat clamps of approved design to

cast iron (spun) pipe embedded in and Including cement concrete

blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded

stone aggregate 20mm nominal size) including cost of cutting holes

8 17.37 and making good the walls etc.

Painting sand cast iron / centrifugally cast iron( spun) iron soil, waste

and vent pipes and fittings with paint of any colour such as

chocolate, grey or buff etc. over a coat of primer (of approval

12 17.65 quality) for new work

17.65.1 100mm dia cast (spun) iron S&S pipe Metre 260 69.55 18,083.00

17.65.2 75mm dia cast (spun) iron S&S pipe Metre 260 52.90 13,754.00

Providing lead caulked joints to sand cast iron/centrifugally

13 17.58 cast(spun) iron pipes & fittings of diameter :.

Digitally signed by AMIT

SINGH 17:17:39 IST

SL. DSR - DSR Rate NS Rate DSR Amount NS Amount

DESCRIPTION OF ITEMS UNIT Qty

Providing & filling the joints with spun yarn,cement slurry & cement

14 17.36 mortar 1:2(1 cement: 2 fine sand) in SCI/CI pipes.

Providing and fixing single unequal plain junction of reqd. degree.

17.48.1.2 Sand cast (spun) iron pipe IS-3989 Each 22 841.10 18,504.20

SITC of 3 HP submersible sump pump for sewage disposal complete

with sewage disposal pipe to the nearest wet point. The works to be

done complete in all respects as per instructions of engineer in

Sub-Total of Drainage Installation, Separate for Scheduled & Non-Scheduled Items 9,14,761.50 2,75,373.84

Digitally signed by AMIT

SINGH 17:17:39 IST

SUB-HEAD - D - SPRINKLER PIPING & ACCESSORIES

SL. DSR - DSR Rate NS Rate DSR Amount

DESCRIPTION OF ITEMS UNIT Qty NS Amount (Rs)

Providing, laying, testing & commissioning of 'C' class

heavy duty MS pipe conforming to IS 3589/IS 1239

including Welding, fittings like elbows, tees, flanges,

tapers, nuts bolts, gaskets etc. and fixing the pipe on

the wall/ceiling with suitable clamp/support frame

and painting with two or more coats of synthetic

enamel paint of required shade complete as

Supplying, fixing, testing and commissioning of

butterfly valve of PN 1.6 rating with bronze/ gunmetal

2 11.0 seat duly ISI marked complete with nuts, bolts,

washers, gaskets conforming to IS 13095 of following

sizes as required :

Providing and fixing ISI Marked of approved make

4 NS Fire Extinguishers complete with all accessories as per

manufacturer's specifications.

4.1 CO2 gas nozzle type - 9 Litre capacity (IS:15683). NOS 4.00 13,802.42 55,209.70

Mechanical Foam gas cartridge type. 9 Kg capacity

ABC dry powder stored pressure type 6 kg capacity

Providing, fixing, testing & commissioning of 15mm dia

quartzoid bulb type sprinklers of rating 68 degree

centigrade with required accessories :

SINGH 17:17:39 IST

SL. DSR - DSR Rate NS Rate DSR Amount

DESCRIPTION OF ITEMS UNIT Qty NS Amount (Rs)

5.4 21.4 Concealed Sprinkler NOS. 158.00 1,397.00 2,20,726.00

Supplying, installation, testing & commissioning of

sprinkler flexible pipe (UL Listed) of stainless steel

complete with 15 NPT on reducer thread with

maximum working pressure of 175 PSI test pressure of

6 875 PSI (Burst) with branch line (Inlet) 25mm NPT male

thread to sprinkler head (Outlet) 15mm NPT female

thread with reducer, nipple, 2 side brackets, center

bracket, stockbar of following sizes complete as

Providing and fixing signages printed on

photoluminescent U1000 aluminium sheet of 1.0 mm

(+ -10%) containing lumigen II as base chemical,

covered under UV stablized coating and of

appropriate size including fixing on wall, door, ceiling

etc. with proper clamps, hangers, cleats anchor

fasteners etc. complete in all respacts as diercted by

Engineer-in-charge SQ INCH 1,650.00 17.83 29,416.07

Providing, jointing and testing of automaticaly

operated Halotron fire extinguishers(cap-

5kg,temperature rating-68degc,test pressure-30bar)

complete with all accessories/fittings. NOS. 1.00 16,568.32 16,568.32

TOTAL CARRIED TO SUMMARY 8,64,649.00 1,54,121.64

SINGH 17:17:39 IST

Summary of Civil and Interior Works

S.No. Description of Works Amount (SR, in Rs.)

2 Masonry & Plaster

3 Paving & Wet Works

4 Partitions & Wall Cladding

7 Finishes & Miscellaneous

GRAND TOTAL (Carried Forward) 2,41,24,424.65

GRAND TOTAL (Carried Forward) 2,41,24,424.65

Digitally signed by AMIT

SINGH 17:17:39 IST

INTERIOR FIT-OUTS for the Proposed Office Space of NEEPCO, New Delhi

DSR-2021 RATE (DSR

S.No. DESCRIPTION UNIT QTY AMOUNT MARKET RATE AMOUNT

Ref. No. 2021)

CIVIL & INTERIOR WORKS

1 DISMANTALING

Demolishing brick work manually / by mechanical means including

stacking of serviceable material and disposal of unserviceable material

within 50 metres lead as per direction of Engineer-in-Charge.

Dismantling doors, windows and clerestory windows (steel or wood) shutter

1.5 15.12 including chowkhats, architrave, holdfasts etc. complete and stacking

within 50 metres lead:

15.12.2 Of area beyond 3 sq. metres EACH 2.00 414.55 829.10

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing

and false ceiling including disposal of unserviceable material and stacking

of serviceable material with in 50 meters lead as directed by Engineer-in-

Demolishing cement concrete manually / by mechanical means

1.7 15.2 including disposal of material within 50 metres lead as per direction of

Engineer-in - charge.

15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) CUM 10.00 2007.10 20,071.00

Carriage of material by mechanical transport including loading unloading

1.1.1 Lime, murrum, building rubbish

TOTAL OF DISMANTLING 2,78,219.90 -

2 MASONRY AND PLASTER

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded

2.1 11.3 stone aggregate) finished with a floating coat of neat cement, including

cement slurry, but excluding the cost of nosing of steps etc. complete.

11.3.1 40 mm thick with 20 mm nominal size stone aggregate SQM 1,315.00 545.00 7,16,675.00

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of

class designation 7.5 in superstructure above plinth level up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) SQM 380.00 1,018.05 3,86,859.00

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at

every third course of half brick masonry.

CEMENT PLASTER :- 15 mm cement plaster on the rough side of single or

half brick wall of mix.

2.5 13.4 12 mm cement plaster of mix

Reinforced cement concrete work in beams, suspended floors, roofs

having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands,

plain window sills, staircases and spiral stair cases up to floor five level

excluding the cost of centering, shuttering, finishing and reinforcement,

with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

Centering and shuttering including strutting, propping etc. and removal of

2.8 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers SQM 12.00 608.35 7,300.20

Digitally signed by AMIT

SINGH 17:17:39 IST

DSR-2021 RATE (DSR

S.No. DESCRIPTION UNIT QTY AMOUNT MARKET RATE AMOUNT

Ref. No. 2021)

Steel reinforcement for R.C.C. work including straightening, cutting,

bending, placing in position and binding all complete above plinth level.

5.22A.4 Hot rolled deformed bars kg 80.00 89.65 7,172.00

POP PUNNING (12mm-15mm) : Providing and fixing Average 12mm to

2.10 MR1 15mm thick POP Punning over cement plaster in line & plumb finished SQM 120.00 304.70 36,563.99

smooth to receive paint. (Internal surfaces of walls).

Providing and laying water proofing treatment in sunken portion of WCs,

bathroom etc., by applying cement slurry mixed with water proofing

cement compound consisting of applying : a) First layer of slurry of cement

@ 0.488 kg /sqm mixed with water proofing cement compound @ 0.253

2.11 22.5 layer will be allowed to air cure for 4 hours. b) Second layer of slurry of SQM 98.00 516.60 50,626.80

cement @ 0.242 kg/ sqm mixed with water proofing cement compound @

0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed

with water curing for 48 hours. The rate includes preparation of surface,

treatment and sealing of all joints, corners, junctions of pipes and masonry

with polymer mixed slurry.

FOAM CONCRETE FILLING UNDER TOILETS AND PANTRY:- Filling and

compacting Foam Concrete for raising level of toilets and pantry and

2.13 MR2 finishing in a coat of lean concrete screeding with waterproofing CUM 30.00 5,559.70 1,66,791.10

compound complete in all respects to take Tile Flooring as per flooring

specifications.

SUB TOTAL OF MASONRY AND PLASTER 14,58,624.08 2,03,355.09

3 PAVING AND WET WORKS

TILE DADO :- Providing and fixing Ist quality ceramic glazed wall tiles

conforming to IS: 15622 (thickness to be specified by the manufacturer), of

approved make, in all colours, shades except burgundy, bottle green,

black of any size as approved by Engineer-in-Charge, in skirting, risers of

steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement :

3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm,

including pointing in white cement mixed with pigment of matching

shade complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be

specified by the manufacturer) with water absorption less than 0.08% and

conforming to IS:15622, of approved brand & manufacturer, in all colours

and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse

3.3 11.41A sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the

joints with white cement and matching pigments etc. The tiles must be cut

with the zero chipping diamond cutter only . Laying of tiles will be done

with the notch trowel, plier, wedge, clips of required thickness, leveling

system and rubber mallet for placing the tiles gently and easily.

b 11.41A.2 Glazed vitrified floor tiles polished finish of size

CERAMIC TILE FLOORING :- Providing and laying rectified Glazed Ceramic

floor tiles of size 300x300 mm or more (thickness to be specified by the

manufacturer), of 1st quality conforming to IS : 15622, of approved make,

3.4 11.40 in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on SQM 243.00 1,225.10 2,97,699.30

20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with

grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white

cement and matching pigments etc., complete.

Digitally signed by AMIT

SINGH 17:17:39 IST

DSR-2021 RATE (DSR

S.No. DESCRIPTION UNIT QTY AMOUNT MARKET RATE AMOUNT

Ref. No. 2021)

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy

grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of

hardener and 0.20 kg of resin per kg), including filling / grouting and

finishing complete as per direction of Engineer-in-charge.

KITCHEN/ PANTRY/ HAND WASH COUNTER :- Providing and fixing pantry

and toilets with Granite stone top (with straight edge polished nosing)

complete with base cabinet made of 19mm BWP board, outside surface

(shutters) finished in 1mm thick Laminate of approved shade. All internal

3.7 MR 3 surfaces to have balancing laminate. The rate inclusive of necessary RMT 18.00 12,114.54 2,18,061.73

hardware, handle lock sets, self closing hinges, spring loaded shutter, latch

inside, all cabinet hardware complete as per Architects approval. (BR of

stone to be taken as Rs 1600/Sqmt). Width of work top counter 600mm/

detailed drawings.

Providing and installation of Printed Nylon Carpet Tiles 600 mm x 600mm

Carpet Tiles or 250 mm x 900 mm Carpet Planks having density 5500 -

6000 gm / m2 , Carpet tile Printed Nylon type-6 construction face carpet

tile with fiber glass polyvinyl chloride backing. The rate shall be inclusive for

Comfolene, GermiShield, Markproof, ActiBack, Stainarmour, Nurturefeet,

Microbefresh, moist proof and the likes with a total thickness of 5.5 to 6.5

3.8 MR 4 mm or as manufacturer’s specification. Carpet tiles shall be complied with SQM 145.00 2,869.08 4,16,016.08

Flammability Test ASTM E648 , Methenamine Pill Test ASTM D2859, Smoke

Density Test ASTM E662, Appearance Retention Hexapod test ASTM D5252.

The laying work should be carried out by the authorized installer of the

Company in India. Carpet Should be Made in India. Manufactures should

have LEED Gold Rating Certificate. Made in India with 10 Year Warranty.

Complete in all respects as per instructions of engineer-in-charge.

Providing and Fixing of floor tiles with wear layer is of 0.5mm, made up of

Stone Polymer composite, 100% Water & Termite proof, Scratch/ Flame/

UV resistant, anti-microbial, 100% recyclable Green product having click

system with suitable skirting. Classification of abrasion resistance (Abrasion

wheelfromH-18 Calibrade, loadApplied 1000 grams, No. of Cycles 14,400).

" ( Along with Matching Profiles)

TOTAL FOR PAVING & WET WORKS 26,63,167.55 14,26,840.83

4 PARTITIONS AND WALL CLADDING

GYPSUM PARTITIONING:- Providing and fixing partition upto ceiling height

consisting of G.I. frame and required board, including providing and fixing

of frame work made of special section power pressed/ roll form G.I. sheet

with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor

and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50

mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to

centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable

anchor fastener or metal screws with nylon plugs and the studs 48 mm

wide having one flange of 34 mm and other flange 36 mm and 0.50 mm

thick fixed vertically within flanges of floor and ceiling channel and

placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and

nuts, including fixing of studs along both ends of partition fixed flush to wall

with suitable anchor fastener or metal screws with nylon plugs at spacing

of 450 mm centre to centre, and fixing of boards to both side of frame

work by 25 mm long dry wall screws on studs, floor and ceiling channels at

the spacing of 300 mm centre to centre.

Digitally signed by AMIT

SINGH 17:17:39 IST

DSR-2021 RATE (DSR

S.No. DESCRIPTION UNIT QTY AMOUNT MARKET RATE AMOUNT

Ref. No. 2021)

The boards are to be fixed to the frame work with joints staggered to

avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick

having two flanges of 9.5 mm each) to be provided at the horizontal joints

of two boards, fixed to the studs using metal to metal flat head screws,

including jointing and finishing to a flush finish with recommended jointing

compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5

mm), joint finisher and two coats of primer suitable for board as per

manufacture's specification and direction of engineer in charge all

75 mm overall thickness partition with 12.5 mm thick double skin fire rated

Glass Reinforced Gypsum (GRG) plaster board conforming to IS: 2095:

Gypsum Panelling:-Providing and fixing, in position concealed G.I. section

for wall paneling using board of required thickness fixed on the ‘W’ profile

(0.55 mm thick ) having a knurled web of 51.55 mm and two flanges of 26

mm each with lips of 10.55 mm, placed @ 610 mm C/C in perimeter

channel having one flange of 20 mm and another flange of 30 mm with

thickness of 0.55 mm and web of length 27 mm. Perimeter channel is fixed

on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with fully

threaded self-tapping dry wall screws. Board is fixed to the ‘W’ profile with

25 mm countersunk ribbed head screws @ 200 mm C/C., all complete as

per the drawing & directions of engineer-incharge, the joints of the boards

are finished with specially formulated jointing compound and 48 mm wide

jointing tape to provide seamless finish.

9.133.3 Gypsum board conforming to IS: 2095 Part - I

GLASS PARTITIONING:- Supply and installation of framed glass partition

with minimal frame, room dividing solution. Single glazed demountable

glass partition using clear toughened glass in natural anodized/ powder

coated finish. Clip-on / U-Section of size 30mm x 21mm with suitable

gaskets for insertion with glass. consisting of clipper two way Clear Profiles,

90 Degree L Junction and T Junction profiles suitable to be used as per

room configuration designs.

Glass thickness - 10mm

All Profiles shall be min 2.5mm thickness excluding Anodizing/ powder

coating, Standards applicable.

• Aluminium profile made by Al Alloy 6063-T6 Grade. Complete in all

respects as per instructions on engineer-in-charge.

PARTITIONING- Partition using 12mm thick fire rated ply fixed on both sides

on aluminium Studs Frame 50mm x 50mm x 1.5mm as per approved

4.4 MR 7 sample and architectural drawings placing the same 600mm c/c on both SQM 290.00 4,039.09 11,71,335.71

horizontal and vertical directions. Aluminuim frame to be fixed to floor and

RCC slab using fastners complete as per instructions of engineer-in-charge.

LOW HEIGHT PLYWOOD PARTITIONING- Low Plywood partition using 12mm

MDF fixed on both sides on Hollow Aluminium Frame 50mm x 50mm as

per approved sample and architectural drawings. Frame to be fixed to

raw floor. The top and visible side edges to be finished in first quality steam

beach wood and duco painted as per the apporved shade and

satisfaction of the Engineer-in charge. All visible MDF surfaces to be

finished with laminate pasting complete with grooves as per the instruction

of the Engineer in charge. Note: only visible areas to be measured.

PANELLING- Panelling using 12mm thick fire rated ply fixed on one side on

Aluminium Frame 50mm x 25mm x 1.5mm as per approved sample and

architectural drawings placing the same at 600mm c/c in both horizontal

and vertical directions. Aluminium frame to be fixed to walls, floor and

Digitally signed by AMIT

RCC Ceiling using fastners complete as per instructions of engineer-in-

charge. AMIT SINGH

SINGH 17:17:39 IST

DSR-2021 RATE (DSR

S.No. DESCRIPTION UNIT QTY AMOUNT MARKET RATE AMOUNT

Ref. No. 2021)

VEENER CLADDING- Providing and Fixing 4.0 mm thick decorative/ Natural

Veneer of approved design and shade , cladded on to existing

partitioning. Complete Cladding to be finished using mellamine polish

(gloss/matt) as approved by the architect. (base rate Rs. 1450/- sqm)

LAMINATE CLADDING- P/F 1mm thick laminate including 4 mm thick MDF,

on an existing Plywood surface.

INSULATION- Providing and fixing thermal insulation with Resin Bonded

rock wool conforming to IS: 8183, having density 48 kg/m3,50 mm

4.9 12.62 thick,wrapped in 200 G Virgin Polythene Bags fixed to wall wirh screw, SQM 290.00 277.90 80,591.00

rawel plug & washers and held and in position by criss cossing GI wire etc.

complete as per directions of Engineer-in-Charge.

Providing and Fixing Channeled Woodworks perforated panels of width

192mm, thickness of 15mm and length 2400 mm or as specified by the

Architect/ approving engineer, made of a high density fibre board with

minimum 725 Kg/M3 density substrate with a laminated facing as per the

approved shade & finish and a melamine balancing layer on the reverse

side. The boards shall have a special perforation pattern where the visible

surface has a “Helmholtz” fluted perforation of 3mm width and

4.10 MR12 5mm/13mm/21mm of visible panel each. The edges of the panels shall be SQM 5.00 4,797.69 23,988.47

“tongue-and-grooved” to receive special clips for installation. The back of

the perforated panel shall have sound absorbing non-woven acoustical

fleece having NRC of 0.52-0.63. The panels shall be mounted on special

aluminium splines using clips. The works to be done complete as per

drawings and satisfaction of engineer-in-charge.

Providing and supplying Acoustical Wall Paneling with square edges

made of fibre glass substrate 9 mm thick and wrapped on the front side

with an acoustically transparent and classified for Fire reaction Class A as

4.11 MR13 per ASTM E-84, fabric as per the selection of the Architect of approved size SQM 40.00 5,360.91 2,14,436.58

providing a minimum sound absorption level of 0.85 NRC to be affixed to

wall using Wall panel impalers and construction adhesives as per the

instructions laid down by the manufacturer.

SHELVES:- Providing and fixing Pre-laminated flat pressed 3 layer (medium

density) particle board or graded wood particle board IS : 3087 marked,

with one side decorative and other side balancing lamination Grade I,

Type II exterior grade IS : 12823 marked, in shelves with screws and fittings

wherever required, edges to be painted with polyurethane primer (fittings

to be paid separately).

STORAGE CABINET FOR ELECTRICAL PANEL AND VOLTAGE STABLIZERS-

Cabinet Shutters out of 19mm Commercial Plybaord finished in 1mm

Laminate of base cost Rs. 380 per sqmt. Shutters to be fixed to a frame.

Rigidly fixed on both sides and top finshed in laminate. No internal carcass

required. All Hinges of hettich or equivalent. Internal Surface of the shutter

in balancing white laminate. All shutters to be provided with Stainless steel

louvers at the top and bottom of the shutter as per the site requirements

and instrcution of the Engineer In charge.

SUB TOTAL OF PARTITIONS AND WALL CLADDING 1,07,043.75 88,80,577.85

Digitally signed by AMIT

SINGH 17:17:39 IST

DSR-2021 RATE (DSR

S.No. DESCRIPTION UNIT QTY AMOUNT MARKET RATE AMOUNT

Ref. No. 2021)

GYPBOARD CEILING :- Providing and fixing false ceiling at all height

including providing and fixing of frame work made of special sections,

power pressed from M.S. sheets and galvanized with zinc coating of 120

gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats

of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at

1200 mm centre to centre, one flange fixed to the ceiling with dash

fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of

cleat fixed to the angle hangers of 25x10x0.50 mm of required length with

5.1 12.45 nuts & bolts of required size and other end of angle hanger fixed with

intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200

mm centre to centre, to which the ceiling section 0.5 mm thick bottom

wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5

mm, at 450 mm centre to centre, shall be fixed in a direction

perpendicular to G.I. intermediate channel with connecting clips made

out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including

fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20

mm and 30 mm long.

Including jointing and finishing to a flush finish of tapered and square

edges of the board with recommended jointing compound , jointing

tapes , finishing with jointing compound in 3 layers covering upto 150 mm

on both sides of joint and two coats of primer suitable for board, all as per

manufacturer's specification and also including the cost of making

openings for light fittings, grills, diffusers, cutouts made with frame of

perimeter channels suitably fixed, all complete as per drawings,

specification and direction of the Engineer in Charge but excluding the

cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095-

300MM X 1200MM MINERAL FIBRE GRID - Providing and fixing of mineral

fiber ceiling tiles, with hot dipped galvanized steel grid work (Silhotte) ,

surface chemically cleaned capping pre-finished in baked polyester

paint, Main Tees of size 38 (H) x 15 mm every 1.2M centre to centre, centre

to centre to form a grid of size 1200 X 300 mm and suspending the grid

from RCC roof using 3 mm GI rod, 6 mm nylon rawl plug and 6mm J bolt

at every 1200 mm intervals. And laying mineral fiber Acoustic ceiling tiles

MV B-Pin of size 1200 x 300 x 20 OCR mm over the formed grid having fire

rating of 60 minutes as per BS 47G / 23 of 1987. Light Reflection of > 85%.

Noise Reduction Coefficient (NRC) of 0.70, Sound Attenuation of 32 db, K

= 0.52-0.57 W/mk. Humidity Resistance up to 99% at 50’C. The grid to be

used is Silhoutte type as per approval of the architect

TRAP DOOR :- Providing and fixing trap door in false ceiling made of

"Novapan "pre-laminated board with hardwood framing, dead locks,

lapping all around including all hardware, hinges etc. complete as per

design and drawing.

CEILING PELMETS :- Providing and fixed pelmet of overall size

150mmx150mm and made hardwood framings hung from ceiling

5.5 MR18 @1000mm centre to centre with 2 nos of 6mm thk. Commercial ply on RMT 20.00 1,425.08 28,501.55

vertical & 12mm thk. Commercial ply on horizontal surface (straight &

curved). Inclusive of finishing in Paint.

WOODEN LAMINATE CEILING :- Providing and fixing wooden Laminate

ceiling by 1mm lamimate on 4 mm mdf fixed to 12mm Underlay

5.6 MR19 commercial Ply fixed to a subframe made using 50mm X 50mm Kiln SQM 45.00 7,345.50 3,30,547.56

seasoned and chmeically treated hollock wood fixed to RCC ceiilng using

Providing the gypsum single sided cove of 150mm x 150mm having a Digitally signed by AMIT

facia of 75mm to macth the specifications same as gypsum ceiling.

SINGH 17:17:39 IST

DSR-2021 RATE (DSR

S.No. DESCRIPTION UNIT QTY AMOUNT MARKET RATE AMOUNT

Ref. No. 2021)

Providing the wooden cove of 150mm x 150mm having a facia of 75mm

to macth the specifications same as above

GYPSUM BOARD VERTICAL BAND- upto100mm high gypsum band all

round the mineral fibre/ gypsum ceiling. In order to make the Mineral

5.9 MR22 Fiber/ gypsum ceiling higher than the Gypsum Ceiling by upto 100mm as RMT 145.00 373.64 54,178.00

per drawings. (visible surface of gypsum band to not exceed 100mm)

including plastic emulsion paint.

Providing and fixing of Triangular Box ceiling of approved manufactured

from light weight G.I and folded into u shape profiles. Each panel has a

nominal cell wall thickness of 15 mm to give a precise engineeredceiling

appearance. It has a width of 15mm and height 60mm. Maximum length

available is 2 mtr and its thickness 0.45 in G.I. It has equilateral triangles

having each side length 175mm. It allows fire detection and

controlsystem, air conditioning and other services to be located within the

ceiling void. all complete as approved & directed by Engineerin-Charge.

Providing and Fixing SoundScapes - Acoustical clouds which are 30 mm

thick, flat glass fiber panels with Humidity Resistance RH 90% & Recycled

Content of minimum 30%, come in various shape options like Square /

Convex / Concave / Circle / Hexagon / Trapezoid / Parallelogram (Left &

Right) / Rectangle (Small & Large) and in standard Traffic White color with

LR 90% or in the color specified by the Architect / Engineer in charge (Ivory

/ Pale Green / Pastel Blue / Traffic Grey / Pale Brown). or in the color

specified by the Architect / Engineer in charge (Ivory / Pale Green / Pastel

Blue / Traffic Grey / Pale Brown) -1200*1200*30mm in Circle

Providing of Baffle ceiling system comprises of 50 mm x 100 mm (50 mm

width & 100 mm Height) U Shape panels in wooden finish. Panels shall be

made of 0.5 mm thick galvanized steel after Powder-coated and length

up to 4000 mm. Panel shall be high corrosion resistance and good color

stability. Centre to Centre panel gap will be 100 mm. Panels are fixed on

to roll formed carriers 20 mm wide x 40 mm deep out of 0.80 mm G.I sheet

MR25 Powder-coated color with cutouts to hold the panels in module of 50 mm SQM 105.00 9,518.01 9,99,390.56

at maximum 1200 m c/c. Carriers are suspended from the roof or truss by 6

mm dia. galvanized steel wire rod hanger with special height adjustment

suspension clip at max. 1200 mm c/c. Hangers are fixed to the roof by ‘J’

hooks or ceiling brackets and nylon inserts. Panels are factory cut in

lengths up to maximum 4.0 m to suit site dimensions or shop drawings. Top

cap and side cap are used to cover the edges of the panels.

SUB TOTAL OF CEILING 13,04,091.10 25,31,255.05

6 DOORS/ WINDOWS

35MM THICK LAMINATED FLUSH DOOR WITH FLOOR SPRING- 35mm thick

flush Doors finished using 1mm Thick Highland Pine Laminate on both sides

panel of size upto 2400mm x 1050mm complete with Hardware including

floor spring, Door Closer, dead Lock with inbuilt key, D-Handle etc.

including cost of teak lipping all around with melamine/ duco finish. The

item to include installation of all kinds of latches as per the requirement.

Digitally signed by AMIT

SINGH 17:17:39 IST

DSR-2021 RATE (DSR

S.No. DESCRIPTION UNIT QTY AMOUNT MARKET RATE AMOUNT

Ref. No. 2021)

Stile Glass door

Supply & installation of Stile Door with Sleek System for 70x45mm Profiles.

Stile Door frame of size 70X45mm with natural anodized/powder coated

and including Flush Hinges (4Nos) & Lock with lever / H/D handle for

rebated door (1 Nos.) and Door closer with 10mm clear toughened glass

and necessary seals to be provided all around the door frames including

installation charges for doors complete with all accessories as required in

Single Leaf Stile Door with size uptp W1050mmx H2100mm with Natural

Anodized Finish.

Single Leaf Stile Door with size upto W 900mmx H2100mm with Natural

Anodized Finish.

Providing and fixing of 35mm thick flush door of size 0.9m width X 2.4m (h)

finsihedin 1.0mm thick laminate of approved shade and color on both

sides in paatern as per design and instrcutions of Engineer In charge. Th

item to include teak wood frame of section 65mm X 150mm finished in

matt coat melamine polish complete with base prearation, stain as per

approved saample. The item to include heavy duty concealed door

closer, matt SS finish mortice lock with lever hadle and all other acessories

like hinges, door stopper, screws, etc. complete required as per design.

The cost to include making of shadow groove as per design. All hardware/

fittings to be matt/ gloss as per approval of the client.

Providing and fixing of 35mm thick flush door of size 0.75m width X 2.4m (h)

finsihedin 1.0mm thick laminate of approved shade and color on both

sides in paatern as per design and instrcutions of Engineer In charge. Th

item to include teak wood frame of section 65mm X 150mm finished in

matt coat melamine polish complete with base prearation, stain as per

approved saample. The item to include heavy duty concealed door

closer, matt SS finish mortice lock with lever hadle and all other acessories

like hinges, door stopper, screws, etc. complete required as per design.

The cost to include making of shadow groove as per design. All hardware/

fittings to be matt/ gloss as per approval of the client.

CONCEALED DOOR CLOSERS:- Providing and fixing aluminium extruded

section body tubular type universal concealed hydraulic door closer

(having brand logo with ISI, IS : 3564, embossed on the body, door weight

upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with

double speed adjustment with necessary accessories and screws etc.

MORTICE LOCK AND LEVER HANDLES- Providing and installing Tubular

Handle TH 123 with Roses & Escutcheon in SS packaged with Mortice

lockset 55mm backset, 20 SS forend, SS strike plate and EP Cylinder for all

TOWER BOLTS:- Providing and fixing aluminium tower bolts, ISI marked,

6.11 9.97 anodised (anodic AC 10 as per IS : 1868 ), transparent or dyed to required

colour or shade, complete:

Digitally signed by AMIT

SINGH 17:17:39 IST

DSR-2021 RATE (DSR

S.No. DESCRIPTION UNIT QTY AMOUNT MARKET RATE AMOUNT

Ref. No. 2021)

DOOR STOPPER:- Providing and fixing bright finished brass hanging type

floor door stopper with necessary screws, etc. complete.

FIRE DOOR- Providing and fixing single leaf 120min Rated Fire Door of size

900x2400. with vision panel using wired glass complete with Fire proof door

frame. One side to be finished in fire retardant paint and one side to be

finished in Laminate of approved shade. All Frame to be finished in fire

retardant paint. All hinges and hardware to be thermatically sealed and

120 mins fire rated.

Providing and fixing 12 mm thick frameless toughened glass door

shutter of approved brand and manufacture, including providing

6.16 21.18 and fixing top & bottom pivot & spring type fixing arrangement and SQM 2.40 4,540.70 10,897.68

making necessary holes etc. for fixing required door fittings, all mplete

as per direction of Engineer- incharge.

SUB TOTAL OF DOORS 15,605.68 22,02,276.47

7 FINISHES & MISCELLANEOUS

PRIMER: Applying one coat of water thinnable cement primer of

7.1 13.43.1 approved brand and manufacture on wall surface. Water thinnable SQM 1,400.00 64.45 90,230.00

ACRYLIC EMULSION PAINT: Painting of wall, ceiling, POP/ plastered,

Gyspum etc. surfaces with smooth and even finish velvet touch paint of

7.2 MR34 approved brand and manufacture to give an even shade. Two or more SQM 1,400.00 247.46 3,46,438.27

coats on new work complete to the satisfaction of the Engineer- in -

charge complete with the preparation of the base etc.

Providing & fixing imported decorative Poly décor fabric Wall Paper

(on walls and ceiling) of weight 475 g /sqm as per approved shade &

design including prepration of surface with 2 coats of Nubin Glue based

Supply and installation of ready to use modular, portable, magnetic glass

writing boards formed of, industrially made 4mm lacquered glass

(Premium GRIHA rated, glossy, stain free, weather proof, opaque,

annealed lacquered glass), encased in aluminium extrusions (T3 grade,

anodized to matt black or approved color), complete with matching

aluminium die casted corner profiles ; 0.4mm GI sheet to be pasted (with

Modified acrylic PVC film (carrier) adhesive tape with Shear Stength of

60N/625mm2, highly suitable for mirror / glass surfaces to Metal contact.)

behind lacquered glass (to imaprt compatiability with magentic

accessories ) and protected with 10mm heavy duty XLPE Foam backing

for impact resistance.

Installed thickness - 18mm.

Supply to include wall mounting clamps, with screws, magnetic duster

and compatible magnetic buttons

Glass color as per Architect's choice from standard shade card.

Corner Profile - Straight / Curved (50mm radius)

Digitally signed by AMIT

SINGH 17:17:39 IST

DSR-2021 RATE (DSR

S.No. DESCRIPTION UNIT QTY AMOUNT MARKET RATE AMOUNT

Ref. No. 2021)

HONEYCOMB BLINDS -Original Non -woven honeycomb shades having

soft fabric appearance and high energy -efficient fabric with high tear

strength constructed out of Anti static , anti-UV, damp proof , resilient,

colour fast & Sanitized Treat 100% spun bonded non -woven polyester fibre

& precision manufacture to form a hexagonally shaped cell . Cell size

3Ú4”Honeycomb structure with dis nct air pocket for energy efficiency

and increased insula on. Shadings are single tone facing both exterior

and interior .Being a Low shading co -efficient will have following Comfort

rating & solar optical properties. Aluminium profile should have temper WP

consisting of alloy 63400 along with anodizing of 10 micron and powder

coating of 60 micron. The tensile strenghth of profile should be 9.10 Kg/mm

square and elongation 18.The control clutch drive unit engineered heavy

duty chain drive pulley operating system consisting of gear clutch housing

and locking plug containing minimum 6 ribs and inserted at minimum of

7.6 MR37 38mm into roller tube . It is self -lubricating Exclusive clutch with safety pins SQM 42.00 3,918.63 1,64,582.26

for secure bracket installation and unlocking pin for quick manual

removal. Universal clutch is most convenient for large windows down to

the smallest windows . It shall be driven by a ball chain pulley with ball

chain and can be positioned at Right hand or Left hand side of the shade .

Clutch gear ratio of 1.75:1 for reduced operating force on larger blinds ..

Mounting hardware brackets universal brackets including end plug

bracket with lock down retainer device . Brackets finish of powder coated

metal installation brackets made of stamped and hardened steel . Roller

tube circular -shaped aluminium tube extruded from alloy 63400 and

temper WP . Bottom rail flat -shaped extruded aluminium from alloy 63400

and temper WP . Ball chain shall be 2mm diameter cord with plastic balls

moulded to form an endless ball chain . It is used for raising or lowering

action of the shades . Plastic parts all plastic components are UVstable

compounds available white.

ZEBRA BLINDS - 190g/sqm, thickness - 0.50 mm - 0.70mm ( opaue part ),

Colorfastness to light - above 4 grade. Blind tube is made of Aluminum

with a diameter of 36mm, botom rail is made of Aluminumwith powder

coated having weight 390 gm/meter fitted with end caps in colour

matching to thefabric and mechanism is of plastic with chain and metal

bracket. The Blinds comes with Aluminum cover with the matching fabric

designed on it. Aluminium profile should have temper WP consisting of

alloy 63400 along with anodizing of 10 micron and powder coating of 60

micron. The tensile strenghth of profile should be 9.10 Kg/mm square and

elongation 18.The control clutch driveunit engineered heavy duty chain

drive pulley operating system consisting of gear clutch housing and

locking plug containing minimum 6 ribs and inserted at minimum of 38mm

into roller tube. It is self-lubricating Exclusive clutch with safety pins for

7.7 MR38 secure bracket installation and unlocking pin for quick manual removal. SQM 10.00 3,655.28 36,552.85

Universal clutch is most convenient for large windows down to the smallest

windows. It shall be driven by a ball chain pulley with ball chain and can

be positioned at Right hand or Left hand side of the shade. Clutch gear

ratio of 1.75:1 for reduced operating force on larger blinds.. Mounting

hardware brackets universal brackets including end plug bracket with

lock down retainer device.Brackets finish of powder coated metal

installation brackets made of stamped and hardened steel. Roller tube

circular-shaped aluminium tube extruded from alloy 63400 and temper

WP. Bottom rail flat-shaped extruded aluminium from alloy 63400 and

temper WP. Ball chain shall be 2mm diameter cord with plastic balls

moulded to form an endless ball chain. It is used for raising or lowering

action of the shades. Plastic parts all plastic components are UV-stable

compounds available white. Digitally signed by AMIT

SINGH 17:17:39 IST

DSR-2021 RATE (DSR

S.No. DESCRIPTION UNIT QTY AMOUNT MARKET RATE AMOUNT

Ref. No. 2021)

FROSTEDFILM(CRYSTALQUALITY):-Providing and fixing frosted film in

approved pattern over glass surface with 15 yrs MCS warranty including

cutting in desired pattern as approval of the Architect. (Only film surface

area shall be measured and paid).

Supply and installation of Perforated Window Graphic Film , 4-mil, opaque,

cast vinyl film with a high gloss finish allowing the full graphic image to be

seen on one side and still allowing viewing through the window from the

other side with Continuous, non-perforated liner, White on the outside

facing image side, black on the see-through reverse side. The Film shall be

self adhesive with Pressure-sensitive adhesive which shall be Removable

with heat. The film shall be installed with approved artwork digitally

reproduced with water-based inks certified to have no hazardous air

pollutants. Self-adhesive, bubble-free installation to be done on a smooth,

dust free putty surface that has a coat of oil-based primer, by Authorized

Installers only. The film shall be tested against ASTM E84 reports: 8170 for

flamability standards. Certificate of image license and Interior E- Warranty

for a period of 36 months. The work shall be carried out as per guidance

and instructions received from Engineer/Architect incharge.

Reception Table:-Providing & Installation of Reception table of of size

upto 1.8m x 0.75m x 0.75m/ 1.2m (ht), made out of 19mm thk. Commercial

Board finished in Acrylic Solid Surface of approved shade and colors

7.11 MR41 complete as per design. One (1) number Drawer pedestal with 3 lockable Nos. 2.00 1,32,972.14 2,65,944.28

drawers and channels (all hardware from Hettich) to be provided under

the table to be finished in Solid Acrylic surface. All visible surfaces to be

finished using Acrylic solid surface as per details.

Conference Table - Providing & Installation of Custom made 'U' shaped

Board Room Table complete as per design having straight/curved edges

out of the overall size of upto length 7.5 m, ht . 0.75m, width 4.5 m, in

19mm thk. Commercial Board base finished in 1mm thick laminate as per

design and shade. Table top to be made in 19mm thick commercial

board and finished in 6 mm thick acrylic solid surface of approved pattern

and shade having edge of 50-75mm thick tapered edge on all sides. Legs

of the table to be upto 150mm x 150mm (Numbers as per design) made in

18mm thick commercial ply cladded in laminte to match the table finish

and hollow for taking the wires upto the table and a 19mm Thk

Commercial board Raceway (150 x 150 ) below table top to be provided

for carriage of cables. All surfaces to be finished in 1mm thick laminte of

approved shade and pattern. The cost to include making of cut outs

necessary for electricity pop up boxes. All veneer surfaces to be finsihed

Digitally signed by AMIT

SINGH 17:17:39 IST

DSR-2021 RATE (DSR

S.No. DESCRIPTION UNIT QTY AMOUNT MARKET RATE AMOUNT

Ref. No. 2021)

Providing and fixing of 4,6 mm thick annealed GRIHA rated lacquered

glass manufactured industrially by curtain coating process with PU

lacquer (50 micron thick), opaque (if viewed against a support wall)

conforming to EN 16477 standards for back painted glass , of approved

color by Architect/ Client fixed with compatible Silicone having Shear

Bond Strength (Dry, 24 hours), greater than 450 kpa and tack free time of

10 to 30 mins compatible for installation of mirror and lacquered glass /

Foam based double sided adhesive tape for instantaneous adhesion,

compatible with mirror and lacquered glass having Shear bond strength

(Dry, 15 mins) of 250 to 350 kpa) on a perfectly leveled 12mm thick water

proof marine plywood / MDF / Mineral fibre board which is mounted on

the RCC wall/any other structure. The contractor should submit test reports

for backpainted glass from manufacturer - High humidity Resistance

(conforms to BS EN 1036 1999); Color fastness ISO 105B02 standard &

Mechanical Resistance ISO 7784 ( Taber Abrasion test ) ISO 2409 ( Cross

Hatch Test ) standard The manufactured backpainted glass should be

environmentally friendly (no lead, no arsenic, no copper,

noformaldehyde); appropriate recycled content (12% post industrial / 6%

post consumer); compressive strenght (1000 MPa) & tensile strenght (40

MPa),same as float glass

Preparation of complete set of shop drawings including finishing, MEP

services, details, design calcualtions etc. and any other details as and

7.14 MR44 when desired by Engineer In charge /client. A qualified professsional for Percent 1% 7,38,55,975.65 8,86,271.71

the purpose shall be appointed after due appproval from Engineer In

Providing & fixing 12mm Thick. 100% Acrylic solid surface of approved

make and colour using approved Adhesive to 12 mm thk. Waterproof

Plywood of approved brand as per shape, pattern & details given in the

drawing. The rate includes providing & fixing beading, cutting, scaffolding,

nails, all materials, labour, lead, lifts, HOM etc., complete.-for Lift Cladding.

(The make, Shade, pattern etc., to be approved by Architect).

STORAGE CABINET FOR GENERAL STORAGE- Out of 19mm Commecial Ply

Board finished using 4mm thick veneer nd polished in melamine to match

the veneer cladding item. The venner to be same as the venner cladding

under separate sub- head above complete with all hinges, drawer glides

7.16 MR46 and hardware from Hettich or equivalent. All internal surfaces to be SQM 2.00 11,137.37 22,274.74

completed using balancing laminate. Including brass D-type handles for

shutters and recessed type handles for drawers. Storage to be of all

heights as per design. Storage shutters to be made in solid veneer/ glass

as per design and drawings.

SUB TOTAL OF FINISHES 90,230.00 29,63,137.30

Digitally signed by AMIT

SINGH 17:17:39 IST

BILL OF QUANTITIES (BOQ) for the Proposed Office Space of NEEPCO, New Delhi

Summary of Furniture

S.No Location Amount

1 Second Floor

2 Third Floor 47,35,701.30

Digitally signed by AMIT

SINGH 17:17:39 IST

Item Specifications QTY Rate Amount Ref. Image

Providing main table size shall be 1800 Width mm x 900 Depth mm x 740 Height mm .Table top

shall be 25 MDF with 0.6 mm thick post formed laminate and 1 mm thick backing laminate

(bdl)Table Top 25 mm PPB + 0.6 mm thick Post Formed Laminate + 1 mm thick BDL + 2 mm PVC +

Modesty 18 mm thick PPB + Clad 1.0 mm DL .Flat edge Duly sealed with 2 mm thick PVC beading.The

modesty shall be 18 mm thick plain particle board ( ) PPB Clad with 1.0 mm thick decorative

laminate (DL) on both sides. Edge Sealed with 2 mm thick PVC beading.

Providing back unit , Size shall be 1280 Width x 425 Depth x 705 Height.Worktop shall be 25 mm

MDF with 0.6 mm thick post formed laminate and 1 mm thick Backing Laminate ( BDL).Flat Edge

Back Unit duly sealed with 2 mm thick PVC beading. The Modesty shall be 18 mm thick plain particle board 1 75,381.10 75,381.10

(PPB) Clad with 1.0 mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2 mm thick

Providing High back chair.The seat shall be made up of 1.2 +/- 0.1 cm thick hot pressed

moulded reconstituted wood & upholstered with leather and moulded polyurethane foam.

Size of back shall be (W)-46.0cm, (H)-57.0cm & size of seat shall be (W)-49.0cm x (D)-49.5cm.

High Resilience (HR) foam should be used in making seat & back which shall be moulded with

density 45 +/- 2 kg/m ³ and hardness load 16+/- 2 kgf as per IS: 7888 for 25% compression. The

back rest should be connected to the mechanism with a drop-lift mechanism which can be

adjusted in the range of 7.0+/-0.5cm for the comfortable back support to suitable individual

need. Armrests should be pressure die casted in polished aluminium with PP arm tops. The

mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt

ratio of 1:3, Synchronized tilt, Back tilt with 4 position locking and Side tilt tension adjustment

knob should be operated while taking back support for better adjustment of comfort. The

chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/-

0.3 cm. The pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5

nos twin wheel castor. The size of head rest shall be (W)26.0cm x 12.0cm(L). The size of the

pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin

wheel castors shall be injection moulded in black polypropylene. Overall dimensions of Chair

shall be, Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below.

Height from ground - min 113.5 to max 138.0 cms. Seat height - min 41.0cm to max 51.0 cm.

Dimensions tolerance / variations shall be within +/- 1 cm.

Digitally signed by AMIT

SINGH 17:17:39 IST

Item Specifications QTY Rate Amount Ref. Image

Providing Mid Back Chair.The seat shall be made up of 1.2 +/- 0.1 cm thick hot pressed

moulded reconstituted wood & upholstered with leather and moulded polyurethane

foam. The back shall be designed with contoured lumber support for extra comfort. Size

of back shall be (W)-45.0cm, (H)-49.0cm & size of seat shall be (W)-49.0cm x (D)-49.5cm.

High Resilience (HR) foam should be used in making seat & back which shall be

moulded with density 45 +/- 2 kg/m ³ and hardness load 16+/- 2 kgf as per IS: 7888 for

25% compression. The back rest should be connected to the mechanism with a drop-lift

mechanism which can be adjusted in the range of 7.0+/-0.5cm for the comfortable

back support to suitable individual need. Armrests should be pressure die casted in

polished aluminium with PP arm tops. The mechanism of chair shall have following

features:360 degree revolving type, Seat/Back tilt ratio of 1:3, Synchronized tilt, Back tilt

with 4 position locking and Side tilt tension adjustment knob should be operated while

VISITOR CHAIR taking back support for better adjustment of comfort. The chair shall be provided with 3 35,150.38 1,05,451.14

pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal

shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel

castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm

with castors). The twin wheel castors shall be injection moulded in black polypropylene.

Overall dimensions of Chair shall be, Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as

measured from pedestal below. Height from ground - min 93.5 to max 110.5 cm. Seat

height - min 41.0cm to max 51.0 cm. Dimensions tolerance / variations shall be within +/-

1 cm. The Company shall be from ISO 9001:2015, ISO 14001:2015, 45001:2018, ISO

50001:2018, Product is BIFMA LEVEL 2, INDOOR AIR QUALITY Certified.

Providing of 3 seater sofa. The overall dimensions of the sofa shall be 2060W x 905D x

855H. The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an

additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be

upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU

foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of

density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be

made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and

termite proof as per IS:303.) and pinewood of cross section deviod of major knots and

surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over

understrucrure for cushioning effect. It should be a welded assembly made in Stainless

steel (grade SS 202) tube & plate with plastic endcap.The Company shall be from ISO

Providing Corner table. The Glass shall be 10+/-0.3mm thick black tinted toughened

glass UV glued with bushes made in SS 202 grade for fixing with understructure. It shall

be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762.

Side Table overall dimensions of table shall be Width of table= 60.0 cm, Depth=60.0 cm, 3 8,296.44 24,889.32

height=35.1 cm.Complete all as per the direction of Engineer in Charge.The Company

shall be from ISO 9001:2015, ISO 14001:2015, 45001:2018, ISO 50001:2018 Certified.

Digitally signed by AMIT

SINGH 17:17:39 IST

Item Specifications QTY Rate Amount Ref. Image

Providing Meeting table.The overall size of the wortop shall be 3600mm x 1500mm x

740mm. Worktop shall be made from 25mm thick MDF one side prelaminate board with

0.4mm PVC membrane pressed on to top and having chamfered edge. Soft closing

dual access flap provided for access to power supply and data cables. The Under-

structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2

grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2

MEETING TABLE mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom 1 1,00,256.09 1,00,256.09

edges for improving the aesthetics.The product has a knock-down construction. A wire

raiser made of 0.8mm CRCA MS IS:513. It is epoxy polyester powder coated (DFT 40-60

microns) for flow of wires and cables. A Power box with 2 cutouts on either sides for

standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout

with plate is provided for mounting Audio Visual Cables(eg. HDMI,VGA-A,etc). The

product must be UL Greenguard certified.Complete all as per the direction of Engineer

Providing Meeting table.The overall size of the wortop shall be 3200mm x 1500mm x

740mm. Worktop shall be made from 25mm thick MDF one side prelaminate board with

0.4mm PVC membrane pressed on to top and having chamfered edge. Soft closing

dual access flap provided for access to power supply and data cables. The Under-

structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2

grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2

MEETING TABLE mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom 3 81,291.86 2,43,875.58

edges for improving the aesthetics.The product has a knock-down construction. A wire

raiser made of 0.8mm CRCA MS IS:513. It is epoxy polyester powder coated (DFT 40-60

microns) for flow of wires and cables. A Power box with 2 cutouts on either sides for

standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout

with plate is provided for mounting Audio Visual Cables(eg. HDMI,VGA-A,etc). The

product must be UL Greenguard certified.Complete all as per the direction of Engineer

Providing main table size shall be 1800 Width mm x 900 Depth mm x 740 Height mm .Table top

shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1

mm thick backing laminate (bdl)Table Top 25 mm PPB + 0.6 mm thick Post Formed Laminate + 1

mm thick BDL + 2 mm PVC + Modesty 18 mm thick PPB + Clad 1.0 mm DL .Flat edge Duly sealed with

2 mm thick PVC beading.The modesty shall be 18 mm thick plain particle board ( ) PPB Clad with 1.0

mm thick decorative laminate (DL) on both sides. Edge Sealed with 2 mm thick PVC beading.

Providing back unit , Size shall be 1280 Width x 425 Depth x 705 Height.Worktop shall be 25 mm

thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick

BACK UNIT Backing Laminate ( BDL).Flat Edge duly sealed with 2 mm thick PVC beading. The Modesty shall be 3 64,091.47 1,92,274.41

18 mm thick plain particle board (PPB) Clad with 1.0 mm thick Decorative Laminate (DL) on both

sides. Edge sealed with 2 mm thick PVC Beading.

Digitally signed by AMIT

SINGH 17:17:39 IST

Item Specifications QTY Rate Amount Ref. Image

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and

upholstered seat inner(material-polypropylene) with moulded polyurethane foam and

polyster fabric. the net back should made up of back outer(material-glass fiber filled nylon)

and back inner(material-PP) and upholstered using polyester mesh fabric with high tenacity

yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-51.0cm x (D)-

49.0cm. The supprot spine should made up of high pressure die cast polished aluminium.

Armrest is having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height

adjustment shall be provided in aluminium structure of armrest which is connected to

aluminium back spine and is operated with button. Armtop is made up of PU molded over

plastic inner. The mechanism shall be Active BioSynchro Mechanism. The mechanism of chair

shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-

Synchro mechanism, 5 position tilt limiter giving option of variable tilt angle to the chair. Front-

Pivot for tilt with feet resting on ground and continious lumber support should ensure more

DGM MAIN CHAIR 3 20,378.70 61,136.10

comfort. The mechanism housing should made up of HPDC Aluminium and black powder

coated. The chair shall be provided with pneumatic height adjustment which shall have stroke

of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished aluminium. it shall be

fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-

centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in

black polypropylene. The lumbar support assembly should consists of lumber spine(material-

glass fiber filled nylon) which is fixed to Aluminium back spine. The neckrest assembly consists

of upholstered neckrest inner(material-poly propylene) with moulded polyurethane foam and

polyster fabric. upholstered inner shall be fixed to neck rest cover. neckrest shall be fixed to

back assembly through neckrest spline. Overall dimensions of Chair shall be, Width of Chair -

75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Height from ground - min

109.3 to max 124.4 cm. Seat height - min 45.5cm to max 55.5cm. Dimensions tolerance /

variations shall be within +/- 1 cm.

Providing high back chair.The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The

back is made up of injection moulded glass filled nylon & upholstered using net fabric with

high tenacity yarn. Seat Size:- 47cm(w) × 51.5cm (D). The HR polyurathene foam is moulded

with density =55+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25% compression.

The armrest has an up=Down adjustment of 8.5 ± 0.5cm which is provided in armrest

structure. Armrest top has an integrated layer of thermoplastic elastomer. Armrest is made up

of plastic injection moulded nylon with textured top. It shall have Front pivot synchro

mechanism with following features. 360 degree revolving type, Single point control, front fivot

VISITOR CHAIR tilt, tilt tension adjustment, 4 position locking with anti- shock feature, seat/back tilting ration 6 19,021.59 1,14,129.54

of 1:2. The lumber support consists of polypropylene pad with mouled polyurathene foam &

covered with polyester fabric. The height of lumber pad can be adjusted through two

projecting knobs provided on the rear side of the pad. Lumber pad has an adjustment of 8.0±

0.5 cm in height. The must be greenguard certified. the work shall be carried out as per

guidance and instructions recieved from Engineer Incharge. This shall come along a headrest

from same family. It shall be SCS IAQ certified for Indoor Air Quality.Complete all as per the

direction of Engineer in Charge.The OEM shall be from ISO 9001:2015, ISO 14001:2015,

45001:2018, ISO 50001:2018, Product shall beGRIHA, Indoor Air Quality certified.

Digitally signed by AMIT

SINGH 17:17:39 IST

Item Specifications QTY Rate Amount Ref. Image

Providing of 1 seater sofa. The overall dimensions of the sofa shall be 860W x 905D x

855H. The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an

additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be

upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU

foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of

density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be

made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and

termite proof as per IS:303.) and pinewood of cross section deviod of major knots and

surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over

understrucrure for cushioning effect. It should be a welded assembly made in Stainless

steel (grade SS 202) tube & plate with plastic endcap.The Company shall be from ISO

Providing Corner table. The Glass shall be 10+/-0.3mm thick black tinted toughened

glass UV glued with bushes made in SS 202 grade for fixing with understructure. It shall

be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762.

Side Table overall dimensions of table shall be Width of table= 60.0 cm, Depth=60.0 cm, 3 8,296.44 24,889.32

height=35.1 cm.Complete all as per the direction of Engineer in Charge.The Company

shall be from ISO 9001:2015, ISO 14001:2015, 45001:2018, ISO 50001:2018 certified.

Providing of 3 seater sofa. The overall dimensions of the sofa shall be 2060W x 905D x

855H. The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an

additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be

upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU

foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of

density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be

Waiting Area made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and

SOFA 3 Seater termite proof as per IS:303.) and pinewood of cross section deviod of major knots and

surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over

understrucrure for cushioning effect. It should be a welded assembly made in Stainless

steel (grade SS 202) tube & plate with plastic endcap.The Company shall be from ISO

Providing of 1 seater sofa. The overall dimensions of the sofa shall be 860W x 905D x

855H. The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an

additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be

upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU

foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of

density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be

made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and

Sofa 1 Seater termite proof as per IS:303.) and pinewood of cross section deviod of major knots and 1 24,653.37 24,653.37

surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over

understrucrure for cushioning effect. It should be a welded assembly made in Stainless

steel (grade SS 202) tube & plate with plastic endcap.Complete all as per the direction

of Engineer in Charge.The Company shall be from ISO 9001:2015, ISO 14001:2015,

45001:2018, ISO 50001:2018 certified.

Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes

made in SS 202 grade for fixing with understructure. It shall be a welded assembly made

Centre Table in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of table shall be 1 12,494.21 12,494.21

Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.The Company shall be from

Digitally signed by AMIT

SINGH 17:17:39 IST

Item Specifications QTY Rate Amount Ref. Image

Providing Corner table. The Glass shall be 10+/-0.3mm thick black tinted toughened

glass UV glued with bushes made in SS 202 grade for fixing with understructure. It shall

be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762.

Side Table overall dimensions of table shall be Width of table= 60.0 cm, Depth=60.0 cm, 1 8,296.44 8,296.44

height=35.1 cm.The Company shall be from ISO 9001:2015, ISO 14001:2015, 45001:2018,

ISO 50001:2018 certified.

Supplying of penta workstation of size 1500 X 1500 x 750 with KBPT + pedestal :Providing DESK based

modular workstation with System ht - 750 mm .Understructure - The slanted legs with perforated metal

modesty in between are connected to the understructure with the help of PDC Connectors to provide a

stable and sturdy base for the worktops. Modesty panel shall be of Metal 1.2 mm thick CRCA. Wire

Management : Metal powder coated power box with wire raiser+D56 is given to pull wires from the floor

PA/PS TABLE junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop 2 79,700.10 1,59,400.20

above power box cut out for accessing switches.Worktop mounted metal modesty made from 0.8 mm thk

CRCA (IS: 513) is provided.Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping

edge banding of size 1200 mm w x 600 mm d.Pedestals - Nova pedestal flat metal front, full ht free

standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. .The product should

be GREENPRO, SCS IAQ, GRIHA, BIFMA certified.

Providing chair.The cushioned seat and back assembly consists of seat base moulded

in glass filled Poly-amide, moulded polyurethane foam and upholstered with high

stretch knitted polyester fabric. The back size shall be 45.5cm W x 53.0cm H. The HR

polyurethane foam used in seat and back cushion is moulded in density 45kg per m3.

The seat and back are firmly connected to the base frame and are cantilevered in such

a way that it gives a multi dimensional movement possibility just with a simple lean on

the sides or back, without need for complex manual adjusments. The cantilevered seat

offers impact cushioning while seating and synchronises with the back movement

during posture changes. The ‘S: shaped spines moulded in high strength glass filled

PA/PS CHAIR Polyamide and the spine connector moulded in glass filled Polyamide form the back 2 10,908.96 21,817.92

spine structure involved in multi dimensional recline motion. The variable tilt angle

recline motion can be adjusted with 3 position Tilt limiter feature which is inbuilt in saet

base and the tension is user weight dependent. The adjustable armrests assembly

consists of armrest housing sliding over the armrest structure, both moulded in glass filled

Polyamide. The pneumatic height adjustment shall have a stroke of 9.2cm.The pedestal

is injection moulded in glass filled Polyamide and fitted with 5 nos. twin wheel castors.

The pedestal is 66cm pitch centre diameter and 76cm with castors. The overall

dimensions of the chair shall be 76cmx 76cm x(99.5-108.8cm). The seat height shall be

(44.5-53.8cm).Complete all as per the direction of Engineer in Charge.The Company

shall be from ISO 9001:2015, ISO 14001:2015, 45001:2018, ISO 50001:2018 certified.Product

is Greenguard, Greenpro, AIOTA Certified.

Providing of table with overall size of table 1200 x 600 x 750mM.The table is made of 25

mm thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm

PVC membrane pressed on to top. Soft closing access flap within-build power box are

provided on work surface for wire management. The ERU top is made of 25 mm thick

MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC

membrane pressed on to top. The modesty panel is made of 25 mm thick MDF one side

pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on

to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2

grade and approved shade edge banded with matching 2 mm thick PVC lipping. The

pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and

approved shade edge banded with matching 2 mm thick PVC lipping.The Company

shall be from ISO 9001:2015, ISO 14001:2015, 45001:2018, ISO 50001:2018, Product is

Greenguard Certified

Digitally signed by AMIT

SINGH 17:17:39 IST

Item Specifications QTY Rate Amount Ref. Image

Providing chair.The cushioned seat and back assembly consists of seat base moulded

in glass filled Poly-amide, moulded polyurethane foam and upholstered with high

stretch knitted polyester fabric. The back size shall be 45.5cm W x 53.0cm H. The HR

polyurethane foam used in seat and back cushion is moulded in density 45kg per m3.

The seat and back are firmly connected to the base frame and are cantilevered in such

a way that it gives a multi dimensional movement possibility just with a simple lean on

the sides or back, without need for complex manual adjusments. The cantilevered seat

offers impact cushioning while seating and synchronises with the back movement

during posture changes. The ‘S: shaped spines moulded in high strength glass filled

Polyamide and the spine connector moulded in glass filled Polyamide form the back

Guard Chair spine structure involved in multi dimensional recline motion. The variable tilt angle 1 10,908.96 10,908.96

recline motion can be adjusted with 3 position Tilt limiter feature which is inbuilt in saet

base and the tension is user weight dependent. The adjustable armrests assembly

consists of armrest housing sliding over the armrest structure, both moulded in glass filled

Polyamide. The pneumatic height adjustment shall have a stroke of 9.2cm.The pedestal

is injection moulded in glass filled Polyamide and fitted with 5 nos. twin wheel castors.

The pedestal is 66cm pitch centre diameter and 76cm with castors. The overall

dimensions of the chair shall be 76cmx 76cm x(99.5-108.8cm). The seat height shall be

(44.5-53.8cm).Complete all as per the direction of Engineer in Charge.The Company

shall be from ISO 9001:2015, ISO 14001:2015, 45001:2018, ISO 50001:2018 certified.Product

is Greenguard, Greenpro, AIOTA Certified.

The seat shall be made of injection molded plastic outer and inner. Plastic inner shall be

upholstered with fabric and moulded polyurethane foam of density 67+/-2kg/m ³, and

hardness load 16+/-2kgf as per IS:7888 for 25% compression. The back shall be made

3.5+/-0.03cm x 1.5+/-0.02cm x 0.2+/-0.016cm of MSERW oblong tube. It shall be

upholstered using net fabric with high tenacity yarn. The dimensions of seat shall be-

46.0cm(W) x 48.0cm(D) and of back shall be 43.0cm(W) x 60.0cm(D). The armrest top

shall be moulded from polyurethane and mounted on to a drop lift adjustable type

tubular armrest support made of dia 3.81+/-0.03cm x 0.2+/-0.01 cm thick MSERW tube.

Armrest height adjustable upto 6.5+/-0.5cm in 5 steps.. The mechanism of the chair shall

have following features : 360⁰ revolving type, Active Bio-synchro mechanism, Tilt tension

adjustment, 5-position tilt limiter giving option of variable tilt angle to the chair.

Seat/Back tilting ratio of 1:2. The chair shall be provided with pneumatic height

RECEPTION CHAIR adjustment which shall have stroke of 10.0 +/- 0.3 cm. Seat depth adjustment shall be 1 15,221.45 15,221.45

integrated in the seat through a sliding mechanism. Seat depth adjustment range shall

be 6.0+/-0.5cm. Back frame shall be connected to the Up/Down mechanism housed in

plastic T spine. it can be adjusted in the range of 7.42+/-0.5 cm for the comfortable back

support to suit individual need. The pedestal shall be injection moulded in black 33% GF

Nylon66. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be

66.1+/- 0.5 cm pitch-centre-dia (76.1 +/- 1.0 cm with castors). The twin wheel castors

shall be made of PP. Overall dimensions of Chair shall be, Width of Chair - 76.1cm, Depth

of Chair - 76.1 cm as measured from pedestal below. Height from ground - min97.3 to

max 114.8 cm. Seat height - min 43.6cm to max 53.6 cm. Dimensions tolerance /

variations shall be within +/- 1 cm. The Company shall be from ISO 9001:2015, ISO

14001:2015, 45001:2018, ISO 50001:2018 certified.Product is GRIHA, BIFMA LEVEL 2 ,

INDOOR AIR QUALITY Certified.

Digitally signed by AMIT

SINGH 17:17:39 IST

Item Specifications QTY Rate Amount Ref. Image

Providing of 2 seater sofa. The overall dimensions of the sofa shall be 1460W x 905D x

855H. The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an

additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be

upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU

foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of

density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be

made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and

termite proof as per IS:303.) and pinewood of cross section deviod of major knots and 1 32,131.12 32,131.12

surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over

understrucrure for cushioning effect. It should be a welded assembly made in Stainless

steel (grade SS 202) tube & plate with plastic endcap.Complete all as per the direction

of Engineer in Charge.The Company shall be from ISO 9001:2015, ISO 14001:2015,

45001:2018, ISO 50001:2018 certified.

Providing of 1 seater sofa. The overall dimensions of the sofa shall be 860W x 905D x

855H. The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an

additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be

upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU

foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of

density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be

RECEPTION SOFA made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and

1 SEATER termite proof as per IS:303.) and pinewood of cross section deviod of major knots and

surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over

understrucrure for cushioning effect. It should be a welded assembly made in Stainless

steel (grade SS 202) tube & plate with plastic endcap.The Company shall be from ISO

Providing Corner table. The Glass shall be 10+/-0.3mm thick black tinted toughened

glass UV glued with bushes made in SS 202 grade for fixing with understructure. It shall

be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762.

Side Table overall dimensions of table shall be Width of table= 60.0 cm, Depth=60.0 cm, 1 8,296.44 8,296.44

height=35.1 cm.The Company shall be from ISO 9001:2015, ISO 14001:2015, 45001:2018,

ISO 50001:2018 certified.

Digitally signed by AMIT

SINGH 17:17:39 IST

Item Specifications QTY Rate Amount Ref. Image

Providing and placing mid back chair ,The seat assembly shall be made up of 1.2 ±0.1cm. thick

hot-pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and shall be

upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions

of seat shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated

(DFT 40-60 microns) tubular frame of dia 2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube

designed with contoured lumbar support for extra comfort. The back shall be upholstered

using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 70.5

cm (H). The HR polyurethane foam shall be moulded with density =45+/-2 kg/m3 and

hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The one-piece armrests shall be

injection moulded from black Co-polymer Polypropylene. The mechanism shall be designed

with 360° revolving type, 17±2° maximum tilt m pivot at centre, Upright position locking., Tilt

tension adjustment. The pneumatic height adjustment shall has an adjustment stroke of 11.0

±0.3cm. The bellow shall be 3 piece telescopic type and injection moulded in Black

Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled Nylon66 and

fitted with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-center dia. (76.3

±1.0cm with castors). The twin wheel castors shall be injection moulded in Black Nylon.

Overall Dimensions of Chair shall be Seat Height - min 43.3 to max 54.3cm, Height - min99.5 to

max 110.5cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-

SEAT SHELL : The seat shell is a welded assembly of seat,back and side frame. The seat

and back are made of 0.12+0.013cm thk CR steel sheet with oblong perforations.They

are welded to sideframe of size 3.2+0.05cm x 0.5 + 0.05 cm thk HR steel.The welded

powder coated ( DFT 40-60 microns ).The seat has a front water fall edge to provide

popliteal clearance for comfortable seating.It also has a buttock support curve that not

only provides rear support but also prevents small children from falling through the gap

between seat and back. Clean and flat surfaces of seat and back aids in easy

maintenance.SEAT SIZE 47.8 cm (W) x 44.6 cm (D) ” BACK SIZE 41.6 cm (W) x 23.0 cm

(HUNDERSTRUCTURE ASSEMBLY: Understructure assembly consists of connecting beam

and leg assembly made of M.S.E.R.W. oblong tube of size 7.5+0.03cm x 2.5+0.03cm x

0.2+0.016cm thk.The welded structure assembly is powder coated ( DFT 40-60 microns

).The leg assembly is fitted with shoes and levellers in Nylon.ARM REST ASSEMBLY: Armrest

assembly consists of armrest frame and armrest pad The armrest frame is made up of

size 3.175+0.05cm x 0.47+0.027cm thk HR steel and it ispowder coated ( DFT 40-60

Bench Type microns ). Armrest pad is injection molded in Nylon and is fitted onto the armrest

Sitting Chair frame.SIDE TABLE ASSEMBLY: It is a welded structure assembly made of 0.12+0.013cm thk

CR steel sheet with oblong perforations which is welded to side strip of size 3.2+0.05cm x

0.5+ 0.05 cm thk HR steel.The welded assembly is powdercoated ( DFT 40-60 microns )

and fitted to understructure assembly.ACCESSORIES : Accessories available based on

specific segment requirements and can be retro-fitted on the product.

BOTTLE / FILE HOLDER : It is a welded mesh made of IZI 0.4cm+0/-0.005cm MS rod. It is

powder coated ( DFT 40-60 microns ) and fitted to understructure assembly.B)LEAFLET

HOLDER : It is a welded mesh made of B 0.4+0/-0.005cm MS rod and is welded to back

of seat shell. It is powder coated ( DFT 40-60 microns ).LINKING CORNER ASSEMBLY: It is a

welded assembly made of two MS ERW round tubes of diameter 1.9+0.02cm X

0.2+0.016cm thk . It is used for connecting two units

(with side table) in L- shaped configuration. It is powder coated ( DFT 40-60 microns ).

CUSHIONS: The cushions for seat and back are made of 1.5 +0.1cm thk foam on a

flat MR grade ply 0.8+0.04cm thk measured as per QA method described in OCP-QLTA-

P14-18 and is upholstered with leatherite.

Digitally signed by AMIT

SINGH 17:17:39 IST

Item Specifications QTY Rate Amount Ref. Image

Product Size: 380mm(W) x 450mm(D) x 1830mm(H). Models: 1 Door, 2 Door, 4 Door & 6

Door (Main unitsandadd-on units)

Stackability - The add-on units can be stacked width wisetoformbank of lockers having

common side panel. Locking - Cam lock with lock lever .Option of hasp

arrangement.Material: CRCA 0.6mmThickness.Construction: Rigid knockdown

construction.Shelf Uniformly Distributed Load Capacity per eachshelf level is 35 Kg

maximum.8. Hat Shelf Only for 1 Door Model at the top.Hanging Rod- For 1 Door – Below

Personal Locking Unit 1 18,342.39 18,342.39

Hat Shelf, For 2 Door – 1 Hanging rod in both compartment . Finish: Epoxy Polyester

Powder coated to the thicknessof 50 microns (+/-10). Handle / Label holder -

Aesthetically appealing Snap fit ABSplastichandle. Plastic label holder

foridentification.Ventilation Attractive punched pattern for ventilation. Accessories

(Optional) Stand for 1 wide, 2 wide and 3 wide – 125 mmHigh (add to unit height)

inclusive of Leveler.

Main Desk size shall be 1500 Width x 750 Depth x 743 Height.Top shall be of 18 mm

thickness made of PLT board with 2 mm Edge banding. Wenge and savannah Maple

PLT board shall be used. The Understructure shall be in pre-laminated panels made with

PLT boards . 2- Drawerand 3 - Drawer storage units with different combinations to support

tops made with 18 mm PLT boards of different colours.Modesty and back panels made

Cubical Table 6 22,896.05 1,37,376.30

with 18 mm PLT boards. The pedestals / storages shall be fitted with necessary locks.

Trident Junior 2 Main Desk size : 1500 W x 750 D x 743 H.Top 18 mm thick PLT board + 2

mm Edge Banding + Wenge and Savannah Maple PLT board + Understructure +

Modesty and back panels with 18 mm PLT boards.The Company shall be from ISO

Providing and placing high back chair The seat assembly shall be made up of 1.2 ±0.1cm. thick

hot-pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and shall be

upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions

of seat shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated

(DFT 40-60 microns) tubular frame of dia 2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube

designed with contoured lumbar support for extra comfort. The back shall be upholstered

using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 70.5

cm (H). The HR polyurethane foam shall be moulded with density =45+/-2 kg/m3 and

hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The one-piece armrests shall be

injection moulded from black Co-polymer Polypropylene. The mechanism shall be designed

Cubical Main Chair 6 11,657.26 69,943.56

with 360° revolving type, 17±2° maximum tilt m pivot at centre, Upright position locking., Tilt

tension adjustment. The pneumatic height adjustment shall has an adjustment stroke of 11.0

±0.3cm. The bellow shall be 3 piece telescopic type and injection moulded in Black

Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled Nylon66 and

fitted with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-center dia. (76.3

±1.0cm with castors). The twin wheel castors shall be injection moulded in Black Nylon.

Overall Dimensions of Chair shall be Seat Height - min 43.3 to max 54.3cm, Height - min99.5 to

max 110.5cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-

Digitally signed by AMIT

SINGH 17:17:39 IST

Item Specifications QTY Rate Amount Ref. Image

The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as

per QA method described in OCP-QLTA-P14-18 and shall be upholstered with fabric upholstery

covers and moulded Polyurethane foam. The dimensions of seat shall be 47.0 cm. (W) x 48.0

cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame

of dia 2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar

support for extra comfort. The back shall be upholstered using Net fabric with high tenacity

Cubical Visitor

yarn. The dimensions of back shall be 46.5 cm (W) x 60.5 cm (H). The HR polyurethane foam 12 10,654.75 1,27,857.00

shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for

25% compression. The one-piece armrests shall be injection moulded from black Co-polymer

Polypropylene. The powder coated (DFT 40-60 microns) tubular frame shall be cantilever type

& made of dia 2.54±0.03cm x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. Overall Dimensions of

Chair shall be Seat Height - 46.5cm, Height - 93.5cm, Width & Depth of Chair as measured

from pedestal -Width-61.0 cm and Depth-64.5 cm.

Supplying of Recta workstation of size 1500 X 600x 750 with KBPT .Providing DESK based modular

workstation with worktop thickness 25mm System ht - 750 mm .Understructure - The slanted legs with

perforated metal modesty in between are connected to the understructure with the help of PDC

Connectors to provide a stable and sturdy base for the worktops. Modesty panel shall be of Metal 1.2 mm

thick CRCA. Wire Management : Metal powder coated power box with wire raiser+D56 is given to pull

Workstation wires from the floor junction box upto the power box fixed under neath the worktop. Aluminium access 20 64,706.79 12,94,135.80

flaps on worktop above power box cut out for accessing switches.Worktop mounted metal modesty made

from 0.8 mm thk CRCA (IS: 513) is provided.Worksurface - out of 25 mm thk prelam particle board with

flat pvc lipping edge banding of size 1200 mm w x 600 mm d.Pedestals - Nova pedestal flat metal front, full

ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. .The product

should be GREENPRO, SCS IAQ, GRIHA, BIFMA certified.

Providing chair.The cushioned seat and back assembly consists of seat base moulded

in glass filled Poly-amide, moulded polyurethane foam and upholstered with high

stretch knitted polyester fabric. The back size shall be 45.5cm W x 53.0cm H. The HR

polyurethane foam used in seat and back cushion is moulded in density 45kg per m3.

The seat and back are firmly connected to the base frame and are cantilevered in such

a way that it gives a multi dimensional movement possibility just with a simple lean on

the sides or back, without need for complex manual adjusments. The cantilevered seat

offers impact cushioning while seating and synchronises with the back movement

during posture changes. The ‘S: shaped spines moulded in high strength glass filled

Polyamide and the spine connector moulded in glass filled Polyamide form the back

Workstation Chair spine structure involved in multi dimensional recline motion. The variable tilt angle 20 10,908.96 2,18,179.20

recline motion can be adjusted with 3 position Tilt limiter feature which is inbuilt in saet

base and the tension is user weight dependent. The adjustable armrests assembly

consists of armrest housing sliding over the armrest structure, both moulded in glass filled

Polyamide. The pneumatic height adjustment shall have a stroke of 9.2cm.The pedestal

is injection moulded in glass filled Polyamide and fitted with 5 nos. twin wheel castors.

The pedestal is 66cm pitch centre diameter and 76cm with castors. The overall

dimensions of the chair shall be 76cmx 76cm x(99.5-108.8cm). The seat height shall be

(44.5-53.8cm).Complete all as per the direction of Engineer in Charge.The Company

shall be from ISO 9001:2015, ISO 14001:2015, 45001:2018, ISO 50001:2018 certified.Product

is Greenguard, Greenpro, AIOTA Certified.

Digitally signed by AMIT

SINGH 17:17:39 IST

Item Specifications QTY Rate Amount Ref. Image

Providing hinged door unit (HDU) of size 1200mm (H) X 900mm (W) x 460mm(D). The top

is 11mm thick bent metal made out of 0.8mm CRCA steel sheet (as per IS:513) powder

coated with DFT 40-60 microns of epoxy polyester powder. The body and side panel are

made of 25mm thick and 18mm thick PLT board respectively with metal cladding of

0.8mm CRCA steel sheet (as per IS:513) from the outside powder coated with DFT 40-60

microns of epoxy polyester powder. 1 No Adjustable and 1 No Fixed Shelf made of

25mm thick PLT is provided with a UDL capacity of 40kg maximum. The doors are made 4 21,906.58 87,626.32

of 18mm thick PLT with a 3-way nickel plated wooden furniture lock and aesthetically

appealing recessed aluminum extrusion handles. Screw adjustable levellers with plastic

base are provided at the bottom for vertical ht. adjustment for floor levelling of units. The

Company shall be from ISO 9001:2015, ISO 14001:2015, 45001:2018, ISO 50001:2018

Providing of full Height Storage,Size of 1980mm(H)x450mm(W)x 500mm(D) x ht without

leveler.Aesthetically appealing completely knock down construction.

The add—on units are stack widthwise to form a row of storage having a common side

panel. (Note— Single Main unit should not be offered.Minimum 1 Main + IAddon to be

offered) Legs fitted with screw type leveler (add 45mm to the height) Made from

combination of CRCA** 0.5 mm & 0.8mm Thickness. CRCA 'D' Grade as per IS-513

Heightwiae Adjustable Shelf Mounting

Each Full shelf has Load Capacity of 40Kg UDI- Max

4 No.s of full adjustable shelves A4 size Box file (85Wx345Hx285D) can be stOred vertically

Full Height Storage 9 35,695.31 3,21,257.79

on all 5 loading levels (Refer Sheet 27 of 27)

This Document is the copyrighted works of Godrej & Boyce Mfg. Co. Ltd. Godrej & Boyce

Mfg. Co. Ltd. reserves all rights whatsoever in the documen Godrej & Boyce Mfg. Co. Ltd.

asserts its rights over this document that has been conceived by the dint of its efforts and

also views reproduction of this document, as it is or by making cosmetic or other

changes, as a violation of its copyright. No part of this document shall be copied or

Epoxy Polyester Powder coated to the thickness of 50 microns (+/—10 micron).The

Company shall be from ISO 9001:2015, ISO 14001:2015, 45001:2018, ISO 50001:2018

Providing main table size shall be 1800 Width mm x 900 Depth mm x 740 Height mm .Table top

shall be 25 MDF with 0.6 mm thick Post Formed Laminate + 1 mm thick BDL + 2 mm PVC + Modesty

Cabin Main Table 18 mm thick PPB + Clad 1.0 mm DL .Flat edge Duly sealed with 2 mm thick PVC beading.The modesty 2 1,03,001.58 2,06,003.16

shall be 18 mm thick plain particle board ( ) PPB Clad with 1.0 mm thick decorative laminate (DL) on

both sides. Edge Sealed with 2 mm thick PVC beading.

Providing back unit , Size shall be 1280 Width x 425 Depth x 705 Height.Worktop shall be 25 mm

MDF with 0.6 mm thick post formed laminate and 1 mm thick Backing Laminate ( BDL).Flat Edge

Back Unit duly sealed with 2 mm thick PVC beading. The Modesty shall be 18 mm thick plain particle board 2 75,381.10 1,50,762.20

(PPB) Clad with 1.0 mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2 mm thick

Digitally signed by AMIT

SINGH 17:17:39 IST

Item Specifications QTY Rate Amount Ref. Image

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon)

and upholstered seat inner(material-polypropylene) with moulded polyurethane foam

and polyster fabric. the net back should made up of back outer(material-glass fiber

filled nylon) and back inner(material-PP) and upholstered using polyester mesh fabric

with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall

be (W)-51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast

polished aluminium. Armrest is having two adjustment, Height(6+/-0.5cm) and depth(6+/-

0.5cm). Height adjustment shall be provided in aluminium structure of armrest which is

connected to aluminium back spine and is operated with button. Armtop is made up of

PU molded over plastic inner. The mechanism shall be Active BioSynchro Mechanism.

The mechanism of chair shall have following features:360 degree revolving type,

Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving

option of variable tilt angle to the chair. Front-Pivot for tilt with feet resting on ground and

continious lumber support should ensure more comfort. The mechanism housing should

made up of HPDC Aluminium and black powder coated. The chair shall be provided

Main Chair with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The 2 20,378.70 40,757.40

pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin

wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/-

1.0 cm with castors). The twin wheel castors shall be injection moulded in black

polypropylene. The lumbar support assembly should consists of lumber spine(material-

glass fiber filled nylon) which is fixed to Aluminium back spine. The neckrest assembly

consists of upholstered neckrest inner(material-poly propylene) with moulded

polyurethane foam and polyster fabric. upholstered inner shall be fixed to neck rest

cover. neckrest shall be fixed to back assembly through neckrest spline. Overall

dimensions of Chair shall be, Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as

measured from pedestal below. Height from ground - min 109.3 to max 124.4 cm. Seat

height - min 45.5cm to max 55.5cm. Dimensions tolerance / variations shall be within +/-

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon)

and upholstered seat inner(material-polypropylene) with moulded polyurethane foam

and polyster fabric. the net back should made up of back outer(material-glass fiber

filled nylon) and back inner(material-PP) and upholstered using polyester mesh fabric

with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall

be (W)-51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast

polished aluminium. Armrest is having two adjustment, Height(6+/-0.5cm) and depth(6+/-

0.5cm). Height adjustment shall be provided in aluminium structure of armrest which is

connected to aluminium back spine and is operated with button. Armtop is made up of

PU molded over plastic inner. The mechanim shall be Active Bio Synchro Mechanism.

The mechanism of chair shall have following features:360 degree revolving type,

Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving

option of variable tilt angle to the chair. Front-Pivot for tilt with feet resting on ground and

Visitor Chair continious lumber support should ensure more comfort. The mechanism housing should 4 19,028.11 76,112.44

made up of HPDC Aluminium and black powder coated. The chair shall be provided

with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The

pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin

wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/-

1.0 cm with castors). The twin wheel castors shall be injection moulded in black

polypropylene. The lumbar support assembly should consists of lumber spine(material-

glass fiber filled nylon) which is fixed to Aluminium back spine. Overall dimensions of

Chair shall be, Width of Chair - 70.5cm, Depth of Chair - 70.5 cm as measured from

pedestal below. Height from ground - 99 cm. Seat height - 49 cm. Dimensions tolerance

/ variations shall be within +/- 1 cm.

Digitally signed by AMIT

SINGH 17:17:39 IST

Item Specifications QTY Rate Amount Ref. Image

Providing of 2 seater sofa. The overall dimensions of the sofa shall be 1460W x 905D x

855H. The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an

additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be

upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU

foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of

density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be

made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and

Sofa 2 seater termite proof as per IS:303.) and pinewood of cross section deviod of major knots and 2 32,131.12 64,262.24

surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over

understrucrure for cushioning effect. It should be a welded assembly made in Stainless

steel (grade SS 202) tube & plate with plastic endcap.Complete all as per the direction

of Engineer in Charge.The Company shall be from ISO 9001:2015, ISO 14001:2015,

45001:2018, ISO 50001:2018 certified

Construction: Rigid Knock Down construction made of 0.8 thk. CRCA Steel conforming to

IS: 513 Gr.D. Each body block consists of 1 Main unit & then Add-on units (0, 1,2,3

depending on no. of bays 1, 2, 3, 4 respectively). Each unit has 6 loading levels with 5

nos. adjustable shelves for 2361 Height body. Front Cover, Back cover, is made of 0.8 thk.

CRCA Steel conforming to IS: 513 Gr.D. The front cover has a pattern of holes on the front

surface for ventilation purpose. Back panels when the entire optimizer layout is locked it

also prevents access to inside files from the outside in case of single body. Shared Panel,

door frame is made of 0.8 thk. CRCA Steel conforming to IS: 513 Gr.D. Door Frame: The

door frame assembly is made of 2 vertical door stiffeners, a top horizontal stiffener and a

bottom horizontal stiffener. Optimizer Height for ground for 2361H body is 2502.5mm

(2361 body + 80 understructure + 61.5 channel system). The bodies including shelves are

given antirust surface treatment & are coated with epoxy polyester powder. It involves

an 8-step treatment consisting of Hot water rinse, Knock of degreasing, degreasing, cold

water rinse, phosphating, cold water rinse, and passivation & dry off oven treatment.

Final finish consists of epoxy polyester powder coating of approved color & shade with a

Compactor Dry Film Thickness of minimum 40 microns. Shelf is made of 0.7 thk CRCA steel

conforming to IS: 513 Gr.D or DD. Its max load bearing capacity is 100 Kg uniformly

distributed per shelf. In case of Push Pull Understructure:- The Understructure is a welded

frame suitably fabricated to bear the loads based on configuration. The frame consists

of the following parts: Main channel, body-fixing channel, body-fixing angle and

bearing-fixing angle. All the components are made of CRCA sheet 2 mm thk conforming

to IS:513. In case of Drive Type Understructure:- The Understructure is a welded frame

suitably fabricated to bear the loads based on configuration.The frame consists of the

following parts: Main channel, body-fixing channel, U-channel and Z-channel. All the

components are made of HR sheet 3 mm thk. conforming to IS:2062. The hand wheel

comprises of a welded metal frame which is then covered by PU using insert- molding

process. The metal frame is made of 3 mm thk. HR conforming to IS:2062. The

handwheel is connected to the rollers through a ‘Sprocket-Chain’ arrangement

mounted on the side of the body. Rail Channels (for Push-pull and Drive type with no

platform): It consists of ‘C’ section 2 mm thk HR sheet & Square 25.4mm X 2mm thk ERW

tube – both connected by screws. Prior to the grouting of the guide channels with the

Digitally signed by AMIT

SINGH 17:17:39 IST

Item Specifications QTY Amount Ref. Image

Providing of main table with overall size of table 2350 x 2350 x 750mm. The main table

shall be of size 2350 x 1150 x 750mm. The side unit shall be 1200 x 600 x 750mm. The table

is made of 25 mm thick MDF confirming to IS-14587:1998 with 0.4 mm PVC membrane

pressed on to top. Soft closing access flap within-build power box are provided on work

surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-

laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.

The modesty panel is made of 25 mm thick MDF one side pre-laminate board confirming to

IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made

of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded

with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated 1 3,99,006.31 3,99,006.31

twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC

lipping. Drawer fronts made of 25 mm thick MDF one side pre-laminate board with 0.4 mm

PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses

powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.

Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of

opening. Pedestals are provided with lock for security.Complete all as per the direction of

Engineer in Charge.

Providing back unit.The Back Unit shall be of dimensions 2350 x 500 x 1800mm. It shall be

made of 25mm thick MDF – one side pre-laminate board confirming to IS-14587:1998 with

0.4 mm PVC membrane pressed on to top. The Slide door unit is made of 25 mm thick Pre-

laminated twin board of E1-P2 grade and approved shade edge banded with matching 2

mm thick PVC lipping. Shutters are made of 25mm thick MDF one side pre laminate board

with 0.4mm PVC membrane pressed on top. Shutters have a soft closing & anti slam

mechanism. Handles are provided for ease of opening. Storage is provided with lock for

Providing High back chair.The seat shall be made up of 1.2 +/- 0.1 cm thick hot pressed

plywood & upholstered with leather and moulded polyurethane foam. The back shall be

designed with contoured lumber support for extra comfort. Size of back shall be W-53cm, H-

95.4cm & size of seat shall be W-54.6cm x D-49cm. High Resilience (HR) foam should be

used in making seat & back which shall be moulded with density 45 +/- 2 kg/m ³ and

hardness load 16+/- 2 kgf as per IS: 7888 for 25% compression. The seat and back should be

arrested together with spine made of 0.8 +/- 0.05 cm thick HR steel and should be powder

coated in black with 40-60 micron DFT (Dry film thickness). The armrest assembly should be

made up of armrest tube, PU armrest and the armrest top. The armrest tube assy. shall be

made of 2.54+/- 0.03cm x 0.16 +/- 0.0128 cm M.S E.R.W support tubes and chrome plated.

The P.U armrest shall be made up of black integral skin polyurethane with 50-70 shore 'A'

hardness reinforced with M.S insert. The armrest top shall be made up of ABS &

upholstered with foam & leather. It shsall have front Pivot synchro tilt mechanism. The

CMD MAIN CHAIR mechanism of the chair shall have following features : 360⁰ revolving type, Knee Tilt 1 40,288.08 40,288.08

system, Seat & back tilting ration of 1: 1.5, Front pivot for tilt with feet resting on ground

ensuring more comfort, Tilt tension adjustment, 5-position locking with antilock back

mechanism which should prevent the backrest from impacting the user when the lock is

released, Static seat depth adjustment 5.0 +/- 0.5cm with 5 position locking. The chair shall

be provided with pneumatic height adjustment which shall have stroke of 9.0 +/- 0.3 cm.

The bellow should be single piece duly blow moulded in black polypropylene. The pedestal

shall be made of die-cast aluminium with buffing finish. it shall be fitted with 5 nos twin

wheel castor. The size of the pedestal shall be 67.0 +/- 0.5 cm pitch-centre-dia (77.0 +/- 1.0

cm with castors). The twin wheel castors shall be made of Nylon injection moulded in black

color. Overall dimensions of Chair shall be, Width of Chair - 77cm, Depth of Chair - 77 cm as

measured from pedestal below. Height of back from ground - min 128.0 to max 137.0 cms.

Seat height - min 49.9cm to max 58.9 cm. Dimensions tolerance / variations shall be within

Providing revolving visitor chair.The seat shall be made up of 1.2 +/- 0.1 cm thick hot

pressed plywood & upholstered with leather and moulded polyurethane foam. The back

shall be designed with contoured lumber support for extra comfort. Size of back shall be W-

53cm, H-73cm & size of seat shall be W-54.6cm x D-49cm. High Resilience (HR) foam should

be used in making seat & back which shall be moulded with density 45 +/- 2 kg/m ³ and

hardness load 16+/- 2 kgf as per IS: 7888 for 25% compression. The seat and back should be

arrested together with spine made of 0.8 +/- 0.05 cm thick HR steel and should be powder

coated in black with 40-60 micron DFT (Dry film thickness). The armrest assembly should be

made up of armrest tube, PU armrest and the armrest top. The armrest tube assy. shall be

CMD VISITOR made of 2.54+/- 0.03cm x 0.16 +/- 0.0128 cm M.S E.R.W support tubes and chrome plated.

CHAIR The P.U armrest shall be made up of black integral skin polyurethane with 50-70 shore 'A'

hardness reinforced with M.S insert. The armrest top shall be made up of ABS &

upholstered with foam & leather. The mechanism of the chair shall have following features

: 360⁰ revolving type without back tilt. The chair shall be provided with pneumatic height

adjustment which shall have stroke of 12.0 +/- 0.3 cm. The beloow should be made up of 3

piece telescopic type & injection moulded in black polypropylene. The pedestal shall be

made of die-cast aluminium with buffing finish. it shall be fitted with 5 nos twin wheel

castor. The size of the pedestal shall be 67.0 +/- 0.5 cm pitch-centre-dia (77.0 +/- 1.0 cm

with castors). The twin wheel castors shall be made of Nylon injection moulded in black

color. Overall dimensions of Chair shall be, Width of Chair - 77cm, Depth of Chair - 77 cm as

measured from pedestal below. Height of back from ground - min 99.4 to max 111.4 cms.

Seat height - min 43.4cm to max 55.4 cm. Dimensions tolerance / variations shall be within

Digitally signed by AMIT

SINGH 17:17:39 IST

Item Specifications QTY Amount Ref. Image

Providing discussion table.The overall size of the wortop shall be 1000mm dia. x 740mm.

Worktop shall be made from 25mm thick MDF one side prelaminate board with 0.4mm PVC

membrane pressed on to top and having chamfered edge. Soft closing dual access flap

provided for access to power supply and data cables. Made of 25mm thick MDF-one side

pre-laminate board with 0.4mm PVC membrane pressed on to top. Gromet provided for

wire management. The Under-structure consists of an Inner Tube Assembly with Top for

Discussion Table 1 31,776.53 31,776.53

Worktop Mounting and Base plate with levellers. The Top Plate is made of 5mm thk hot

rolled steel Plates (HR) (As per IS: 2062) & the bottom plate is made of 8mm thk hot rolled

steel Plates (HR) (As per IS:2062). The Inner Tube Assembly is made of 25.4mmx 25.4mm x

1.2mm thk round electric resistant welded tube (ERW)(As per IS:7138) welded together

using Tungsten inert gas welding. The whole structure is epoxy polyester powder coated

(DFT 40-60 microns). The product has a knock-down construction.

Providing and Placing High Back Chair with overall size of 76.1 cm W x 76.1 cm D x 96.5 –

114 cm H x 43.1 – 53.1 cm Seat Height. The seat is cushioned seat made of injection molded

plastic outer & inner. Plastic inner is upholstered with leatherette and molded high

resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per

IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned

made of PU foam with insitu molded M.S. ERW round tube of size 1.9±0.03cm x

0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The

armrest top is molded from polyurethane and mounted on to a drop lift adjustable type

tubular armrest support made of Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having

chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5 steps. The

adjustable tilting mechanism is designed with following features : 360° revolving type, front-

pivot for tilt with feet resting on ground and continuous lumbar support ensuring more

comfort, tilt tension adjustment can be operated in seating position, 5-position tilt limiter

Discussion Chair 4 35,150.38 1,40,601.52

giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, The mechanism

housing is made up of HPDC aluminium black powder coated. Seat depth adjustment is

integrated in the seat through a sliding mechanism. Seat depth adjustment range is of

6.0±0.5cm. Back frame is connected to the up/down mechanism in plastic T spine. It can be

adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual

need. The pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm. The

pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel

castors. The pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of

twin wheel castors are injection molded in plastic having 6.0±0.1cm wheel diameter and

assembled to pedestal.

Providing of 3 seater sofa. The overall dimensions of the sofa shall be 2060W x 905D x

855H. The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an

additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be

upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU

foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of

density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be

SOFA 3 Seater made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and 1 39,323.37 39,323.37

termite proof as per IS:303.) and pinewood of cross section deviod of major knots and

surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over

understrucrure for cushioning effect. It should be a welded assembly made in Stainless

steel (grade SS 202) tube & plate with plastic endcap.The OEM shall be from ISO 9001:2015,

Providing of 1 seater sofa. The overall dimensions of the sofa shall be 860W x 905D x

855H. The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an

additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be

upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU

foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of

density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be

made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and

termite proof as per IS:303.) and pinewood of cross section deviod of major knots and

surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over

understrucrure for cushioning effect. It should be a welded assembly made in Stainless

steel (grade SS 202) tube & plate with plastic endcap.Complete all as per the direction of

Engineer in Charge.The OEM shall be from ISO 9001:2015, ISO 14001:2015, 45001:2018, ISO

50001:2018 certified.

Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in

SS 202 grade for fixing with understructure. It shall be a welded assembly made in SS202

Centre Table grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of table shall be Width of 1 12,494.21 12,494.21

table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.The OEM shall be from ISO 9001:2015, ISO

Providing Corner table. The Glass shall be 10+/-0.3mm thick black tinted toughened glass

UV glued with bushes made in SS 202 grade for fixing with understructure. It shall be a

welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall

dimensions of table shall be Width of table= 60.0 cm, Depth=60.0 cm, height=35.1 cm.The

OEM shall be from ISO 9001:2015, ISO 14001:2015, 45001:2018, ISO 50001:2018 certified.

Digitally signed by AMIT

SINGH 17:17:39 IST

Item Specifications QTY Amount Ref. Image

Overall Size :Width : 87cm Depth : 86cm Height : 107cm Seating Height : 50 Upholstery: