CERTAIN REPAIRS TO JOINERY, PLASTERING, FLOORING, SANITARY, INTERNAL ELECTRIFICATION WORK, PERIODICAL SERVICES ETC IN MD AND OTM ACCN

Amount

Demolition of cement concrete in ground floors and pavings not exc 15 cm thick below or above ground level.

M & L for cement concrete 1:3:6 type C-2, 75 mm thick using 40mm graded stone aggregates as in path and in plinth protection finished fair and even.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing and removing serviceable tiles to store.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square or rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match,and including 15mm thick screed bed in cm 1:6.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square or rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match ,and including 15mm thick screed bed in cm 1:6.

Ditto as above item no 5 but in vertical surface including 10mm thick backing coat of Cm 1:4.

M&L for ceramic coloured tiles of size 300x200mmx6-7mm thick, on verticals surfaces, set and jointed inneat cement slurry and pointed in coloured cement to match including 10mm thick backing coat plaster in CM 1:4

M & L chequered cement concrete tiles 30cmx 30cm x 25mm with grey cement and pigment set, jointed and pointed in neat cement slurry in floors including 15mm thick screed bed in CM 1:6,complete all as specified

Material and labour for vitrified ceramic tiles 10mm thick, light shade, polished area of each tiles n. exc 0.36 Sqm (square / rectangular) in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed 15mm thick in cement mortar (1:6) finished rough to fix tiles complete all as specified and directed.

M&L for vitrified ceramic tiles 10mm thick, light shade, polished area of each tiles n. exc 0.36 Sqm (square / rectangular) as in vertical surfaces i.e. skirting/dado set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface with & including rendering 10mm thick in cement mortar (1:4) finished rough to fix tiles complete all as specified and directed.

M & L Sand filling under floors or in foundations including watering and consolidation

M&L for machine pressed precast concrete interlocking paver block with Gery cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35Grade

Fixing only 500 ltr rotational moulded polythylene water storage tank (Cylindrical vertical with closed top) hoisted and fixed in position incl dismantling of existing tank of any description complete all as specified.

S&F vitreous china squatting pan Orissa pattern size 580 x 440mm white with front or back inlet, integral foot rest (excluding flushing cistern and flush pipe) fixed including provision of lime concrete bedding etc complete all as specified and directed.

S&F vitreous china wash hand basin, white, flat back 550 x 400mm excluding taps, waste chain and plug and porcelain stopper but including bracket and cutting for and pinning in ends of brackets complete all as specified and directed.

M & L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

S&F in repairs 10 ltrs PVC valveless syphonic action type flushing cistern low level with inlet ball valve float and handle complete all as specified and directed by Engr in Charge.

Taking up or down steel tubing 15mm bore and connection including cleaning for refixing or removal to store.

All as per item No 18 hereinbefore but 20mm dia .

S&F steel tubes medium grade galvanised with all fittings and fixed complete to wallsand ceiling or laid in floor bore of pipe 15mm dia complete all as specified and directed by Engr-in-Charge.

All as per item No 20 herein before but 20mm dia.

S&F in repairs for 15mm dia of pipe, bib taps, cast copper alloy fancy type, chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed.

S&F in repairs for 15mm dia of pipe stop valves,fancy type, chromium plated screwed down high pressure with crutch or butterfly handle screwed bothends for iron pipes or for Unions and fixed complete all as specified and directed by Engr-in-Charge..

S&F in repair 20mm bore of pipe ball valves high pressure of PTMT with epoxy coated aluminium rod & high density polythene ball screwed for iron pipe and fixed. (Min weight for 20mm - 210 gms)

S&F in repairs PVC connection 15mm dia and 45cm long with two Nos of brass checknuts and washers complete

S&F in repair pillar taps, cast copper alloy with capstan heads chrominm plated fancy type, screwed down high pressure with or without lettered Hot or Cold with long screwed shank and fly nuts, srewed for iron pipe and fixed 15mm bore.

S&F in repairs Chromium plated grating 125mm dia circular of approved make and fixing with cement mortar 1:3 on Nahani trap or floor trap.

S&F in repairs tubular towel rail brass chromium plated 20mm dia, D type 60cm long fixed with two plugs (Gutties)

S&F rotational moulded polyethylene water storage tanks, 500 liter capacity (cylindrical vertical with closed top), ISI marked, hoisted and fixed in position all as specified in SSR Part I, fixed in repairs complete all as specified & directed.

S&F rotational moulded polyethylene water storage tanks, 1000 litre capacity, (cylindrical vertical with closed top), ISI marked, hoisted and fixed in position all as specified in SSR Part I, fixed in repairs all as specified & directed.

Dismantling of cast iron drain 75/100 mm dia from floor/walls etc and taking out of trenches/floors.

M&L for cast iron soil waste and vent pipe sand cast any length with or without ears with cement joints fixed to walls 75mm dia

All as per item No 33 above but bore of pipe 100mm dia.

M&L cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) Diameter of outlet in 75mm.

M& L Cement concrete type E-2, 1:5:10 using 40mm brick aggregate as in sunken floor.

M&L for 15mm thick rendering in cement Mortar (1:3) with using 3% Water Proofing Compound as in sunken portion complete all as directed.

M&L for applying evenly a tack coat of industrial bitumen 85/25 @ 1.20 Kg per square mtr including cleaning surfaces.

Taking down shutters of any description n exceeding 1 Sqm each

Taking down shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each.

S&F for Flush shutters, 30 mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides

S&F 2nd class factory made hardwood glazed and Skelton shutters 30 mm thick open rebated and prepared to receive glass, gauge etc(without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, stiles and rails as specified in SSR Part I section 8 clause 8.20 (b)

M&L 19mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame works

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style)consisting of frame made out of MS tubes for top and bottom rail MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site as per direc

S&F Galvanised mild steel wire cloth,0.56mm nominal dia of wire and average width of aperture1.18mm and fixed with tinned tacks, or galvanised wire staples.

M&L for sheet glass 3mm thick ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane, including Hacking out old broken glass of any thickness size or description from wooden frames or metal frames fixed with wooden beads/ putty.

S & F aluminium tower bolt anodised of extruded section 200mm

S &F in repair aluminium anodised 300 mm sliding door with hasp staple (bolt type) and fixing clipsof sheet cast or extruded section and fixing bolts and sliding both of extruded sections.

S & F aluminium anodised type handles 150 mm

S&F Butt hinges, medium weight cold rolled mild steel 100mm size.

S&F Butt hinges, medium weight cold rolled mild steel 75 mm size.

S&F for 125 mm long Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws.

M& L in repair Mild Steel 300 mm, ordinary rat tail rod pattern springs including roller and roller plate fixing by screw ,welding, etc as per requirement and complete all as spd and as directed .

S & F mild steel powder coated pelmet rods including 02 Nos of brackets on each opening complete all as specified and as directed by the Engr in charge.

Demolition of brick work or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles all as spd and directed

M&L for brickwork with subclass 'B' old size bricks, straight or curved on plan exc 6 m mean radius , built in cement mortar 1:6

Taking down cement plaster including raking out joints, hacking for key,scrubbing down with water built in cement mortar complete all as specified and as directed.

M&L for rendering 15mm thick in Cement Mortar 1:4 on fair faces of brick work or concrete surfaces finished even smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick in Cement Mortar 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement

M & L for preparation of newly plastered surface of walls and applying two coats of oil bound distemper(white or tinted) over a coat of chalk whiting primer complete all as specified and as directed by Engr-in-Charge.

M & L for preparation of newly plastered surface of walls and applying two coats of cement base paint over a coat of chalk whiting primer complete all as specified and as directed by Engr-in-Charge.

M&L for prepration of new plaster surfaces of walls & applying two coats of exterior acrylic emulsion paint over of a coat of wall primer and complete all as manufacurers instructions and directed by Engr -in-charge.

M & L for preparation of newly plastered surface of walls and applying three coats of white wash complete all as specified and as directed by Engr-in-Charge.

M & L for preparation of old surface of walls and applying one coats of oil bound distemper(white or tinted) complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of new wooden surface of any description exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer

S&F aluminium anodised frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified complete all as specified and as directed by the Engineer-in-Charge.

M&L for anoised aluminium door shutters, aluminium section weighing 1.00kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, aluminium anoised handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc, complete all as specified and as directed by Engr-in-Charge.

M&L for anoised aluminium window and ventilattor shutters, fixed type without sash bar, aluminium section weighing 1.00kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading screws etc, complete all as specified and as directed by Engr-in-Charge.

S & F double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty

S&F for sheet glass 5.50 mm thick ordinary quality and glazing with oil putty in squares exc 0.5 Sqm each pane complete all as specified and directed by Engineer-in-Charge

Supplying and Fixing plain colour PVC sheet 6mm thick fixed in Aluminium frame work by using suitable adhesive/fixing clips all as specified and directed by Engr-in-Charge.

Supply and fix solid PVC wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification given on page 162 of SSR-2010 Part-II for solid PVC wall lining including 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specification and drawing.and including dismantling of doarding of any discription complete all as specified and directed.

Supply and fixing 4mm thick size 600x600mm HPSC (High pressure steam cured) pre-primered self embossed, textured designerd board E- board classic to be fixed on including GI powder coated grid /section size 600x600mm with main runner 38x24x0.9mm thick, cross tee 28.6x24x0.9mm and wall angle 19x19x0.9mm duly suspended with 6mm dia GI bar hangers 1200mm c/c both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including provision for light fixtures of any size and including taking down old ceiling complete all as specified and as directed.

M&L for prepration of old surfaces of walls and applying two coat of colour wash on wall complete all as specified and directed by Engr -in-charge.

M&L for prepration of old surfaces of walls and applying two coat of white wash on ceiling complete all as specified and directed by Engr -in-charge.

M&L for Complete removal of existing treatment by washing, rubbing down and stopping etc on wall surfaces and applying two coats of cement base paint complete all as specified and directed by Engr -in-charge.

M&L for Complete removal of existing treatment by washing, rubbing down and stopping etc on wall surfaces and applying two coat of Oil Bound Distemper complete all as specified and directed

M&L for prepration of old wooden surfaces of any description not otherwise described over 10 cm width or grith and applying one coat of synthetic enamel paint complete all as specified and directed by Engr -in-charge.

M&L for prepration of old steel surfaces of any description not otherwise described over 10 cm width or grith and applying one coat of synthetic enamel paint complete all as specified and directed by Engr -in-charge.

M&L for complete removal of existing treatments by washing, rubbing down up to reach of plaster surface and stopping etc & finished wall with premium acrylic smooth exterior paints with silicone additives of required shade .New work (Two or more coat applied @1.43 ltr /10 Sqm over and including priming coats of exterior applied @ 2.20 kg /10 Sqm).

Removing existing paint by scrapping with Asian Paints TruCare Wall Sander: L- 01/H-01 (having mechanical vacuum mechanism) having RPM between 600-1500, sanding paper of 60/80 Grit having dia of 7"/9" to make the surface free from dust, loose paint etc. by skilled labour complete all as specified and as directed by Engineer-in-Charge.

Providing and applying white cement based putty @ 1.0 Kg (undiluted) per sq mtr. of average thickness 1 mm, of Asian Paints or its equivalent over the plastered/ old painted wall after scrapping to prepare the surface even and smooth complete. Step 1 : Mix the putty powder by adding 40-50% water and mix it with Asian Paints Trucare Putty mixer (Trucare Putty mixer with min 1400 W power havinng mixer rod of industrial stell grade 45 with the mixing capacity of min 2.5 kg putty per minute) or equivalent Step 2 : Apply the first coat the prepared mixer with the help of fully automatic airless spray machine of putty application of Asian Paints Trucare Graco Spray Machine (Model: EH 230 DI) or equivalant having a DC electric motor of 3.3 KW having flow speed of 6 ltrs per minutes with a maximum pressure 227 bar having maximum tip size 0.039" Step 3: Allow 6-8 hrs time to dry the putty surface. Step 4: Apply second coat of the prepared mixer manually to make to smooth to make the finish even. Step 5: Allow 6-8 hrs time to dry the putty surface complete all as specified and as directed by Engineer-in-Charge.

Sanding of the putty surface with Asian Paints TruCare Wall Sander: L- 01/H-01 or equivalent (having mechanical vacuum mechanism) having RPM between 600-1500, sannding paper of 180 Grit having dia of 7"/9" to make the surface free from dust etc. by skilled labour complete all as specified and directed.

Providing and applying two coats of acrylic washable distemper @ 1.5 kgs /10 sq mtrs diluted with water in 5:3 ratio applied over primimg coat @ 0.8 ltr (undiluted)/10SQM diluted with water in 1:1 ratio with fully automatic airless spray machine of paint application of Asian Paints Trucare Graco or equivalant having an electric motor of min.1 HP with a flow speed of min 2 ltr per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface in both the coats of paint complete all as specified and as directed by Engineer-in-Charge.

Providing and applying two coats of cement based paint @ 1.5 kgs /10 sq mtrs diluted with water in 5:3 ratio applied over primimg coat @ 0.8 ltr (undiluted)/10SQM diluted with water in 1:1 ratio with fully automatic airless spray machine of paint application of Asian Paints Trucare Graco or equivalant having an electric motor of min. 1 HP with a flow speed of min 2 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface in both the coats of paint complete all as specified and as directed by Engineer-in-Charge.

Taking down carefully aluminium / copper point wiring (light / fan / socket or power) complete including fitting such as switches, ceiling roses, socket, light fittings, regulators etc complete and making good disturbed surfaces of walls, floors

Taking down unserviceable Submain wiring of any size as directed by Engineer-In-Charge.

Taking down main switch / DB as directed by Engineer-In-Charge.

M & L for concealed point wiring complete with 1.5 sqmm single core multistranded copper conductor FRLS, PVC insulated and unsheathed cable 650 /1100 volts grade drawn through & including PVC conduit ,medium grade with accessories like bends, tees, junction boxes etc fix on wall or ceiling surfaces including cutting chases as required all as specified including 1.5 sqmm , FRLS type , copper multistranded cable as earth wire including pressed steel sunken boxes for mounting of MODULAR TYPE switch/sockets and regulator and including modular type cover plate white colour all as specified and directed for: (a) One light / fan / call bell point controlled by one, one way switch.

One 3 pin socket out let 5 Amps on same board with other switches.

One 3 pin socket out let 5 Amps on Independent board with other switches.

Ditto all as per item No.94 about but with 2.5 sqmm multistranded copper multistranded conductor FRLS cable with 2.5 sqmm earth wire for one 6 pin socket outlet 15 amps on independent board

S & F switch MODULAR 6 Amps, SP, one way, 230 Volts, AC

S & F switch MODULAR 16 Amps, SP, one way, 230 Volts, AC

S & F socket out let multipurpose MODULAR 5 pin 6 Amps, flush type, 230 Volts

S & F socket out let multipurpose MODULAR 5 pin 6/16 Amps, flush type, 230 Volts

S & F MODULAR fan regulator step type 120W, 02 module complete all as specified and directed.

M & L for concealed point wiring complete with 1.5 sqmm single core multistranded copper conductor FRLS, PVC insulated and unsheathed cable 650 /1100 volts grade drawn through & including PVC conduit ,medium grade with accessories like bends, tees, junction boxes etc fix on wall or ceiling surfaces including cutting chases as required all as specified including 1.5 sqmm , FRLS type , copper multistranded cable as earth wire including sunken type pressed steel terminal boxes and plastic laminated white / coloured top sheet cover 3.0 mm thick for: (a) One light / fan / call bell point controlled by one, one way switch.

One 3 pin socket out let 5 Amps on same board with other switches.

One 3 pin socket out let 5 Amps on the independent board.

Ditto all as per item No. 98 about but with 2.5 sqmm multistranded copper multistranded conductor FRLS cable with 1.5 sqmm earth wire for one 6 pin socket outlet 15 amps on independent board.

S & F switch Piano 5 Amps, flush button type, SP, one way, 230 Volts, AC

S & F switch Piano 15 Amps, flush button type, SP, one way, 230 Volts, AC

S & F socket out let multipurpose 5 pin 5 Amps, flush type, 230 / 250 Volts

S & F socket combination ,6 pin ,15 amps, flush type, multipurpose, 230 / 250 volts , AC with ISI marked

M & L ceiling rose surface bakelite 65 x 50 mm three terminals complete all as specified.

M & L for sub main wiring with two single core PVC insulated and unsheathed cable 6 sqmm with multi stranded copper conductor , FRLS type cable drawn through and including PVC concealed conduit of not less than 25mm in size complete with all accessories alongwith provn of 6 sqmm PVC insulated and unsheathed ,multi stranded copper conductor , FRLS type cable as earth wire.(Three runs of cable and one run of conduit shall be measured as one unit)

Supply , installation & commissioning MCB Load Distribution board TPN 4 way double door, for mounting DP/ SP/TP/ MCBs/MCCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossy finished with epoxy polyester based powder coated and baked at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DP/SP/TP MCB shall be of same make as DB. DB shall also be provided with label marking indicating the incoming and outgoing circuits on all way as specified. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified and directed at site .

S&F MCB TPN 63 Amps, 4 pole , 16 kA 415 volts complete all as specified and directed.

Supply and fix DB,double door, SPN 8 way for MCB, 240 volt with 200 amps rated bus bar.

S&F MCB SPN 40 to 63 Amps 240 volts

S&F MCB SP 6-32 Amps 240 volts

Supply and Fix recess/ceiling mounting LED light 1x36 Watt cool white light of 6500k complete all as specified and directed. Make: Havells model No - DROPDWONFLAT2x2PLR36WLED857S or equivalent in CG/Philips

Supply & fixing in replacement LED street light fitting 30 Watt including LED lamp pressure die cast aluminum IP66 with surge protection device of 10KV, IK7 LED (SEOUL) 6500K and connecting electrical to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.50 mm 3 core including GI pipe 32mm light grade 0.9 Mtr long bent to L shape in 02 Nos of GI Clamps of size 25x6 mm of length 25mm with nuts, bolts and washers complete complete all as specified and directed.

Supply & fixing in replacement LED flood light fitting 120 Watt including LED lamp pressure die cast aluminum IP66 with surge protection device of 10KV, IK7 LED (SEOUL) 6500K and connecting electrical to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.50 mm 3 core including GI pipe 32mm light grade 0.9 Mtr long bent to L shape in 02 Nos of GI Clamps of size 25x6 mm of length 25mm with nuts, bolts and washers complete complete all as specified and directed.

M & L Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings

Supply and lay cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core

Supply and lay cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core

Supply and laying GI Tube Med grade 50mm dia incl all fitting all as specified and directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 Mtr wide and not exc 1.5M depth for laying of UG cables and getting out all as specified and directed

Returning, filling, including spreading, levelling, watering and well ramming in layers not exc 25cms thick each layer complete all as specified and directed.

M & L river sand in trenches as cable cushioning 8 cm below the cables and 15cm above the cable which is to be punned down all as specified and directed.only punned thickness will be measured.

Removing the surplus excavated materisl/soil to a distance not exc 50Mtrs and depositing, where directed at a level not exceeding 1.5 Mtr above the starting point all as specified and directed.

Supply and lay burnt bricks sub class 'B' old size laid across the cable in trenches as protection to the cable all as specified and directed.

Supply and Fix PVC Conduit pipe Med Grade of size 25mm with all accessories like (Bend/Tee/Junction box) complete all as specified and directed.

M&L for earthing complete with GI steel earth plate electrod 60x60cmx6.00mm thick bouried directly in ground /earth pit not less than 2.25m deep below the ground level with top edge of the plate not less than 1.5 m below the normal ground level connected to test point by using GI wire of dia 4 mm as earthing lead soldering/revated to earth plate at one end and connected DB by means of nut, bolts etc complete with PCC pit (1:3:6) type GI cover with handle funnel with watering pipe wire mess GI protection pipe for earthing lead all complete as specified and as per electric plate No.5 of SSR Part I

Supply and fixing ceiliing fans down rod of length 3 feet, incl fan hook with rubber real complete all as specified and directed.

Barmotra Infrastructures

M/S Vinod Kumar

M/S Kuldip Construction Co.