REPAIR TO WATER SUPPLY INSTALLATION AND ALLIED WORKS OF B and R NATURE UNDER GE UMROI

Amount

Dismantling posts or struts (wood, steel or RCC) any section, including taking out embedded portion and making good disturbed ground surfaces.

Dismantling Barbed wire/chanlink fencing of any gauge & size exceeding 4 Kg/Sqm complete all as directed by Engr-in-Charge.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, getting out in soft/loose soil complete all as specified and directed.

M/L PCC(1:2:4) type B2 (using 40mm graded aggregate) in foundation filling and mass concrete complete all as specified and directed

Fixing only chain link fencing in-cluding line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire all as specified & directed.

Supply only mild steel Galvanised wire Chain link fencing square mesh of size 100x100mm made out of 4mm dia wire complete all as specified & directed

S&F of Mild steel angle/flat iron supports for posts/strut for securing barbed/chain link fencing any description including drilling holes, notching for wire etc complete all as specified.

Supply only mild steel 10mm dia round bars to secure Chain link fencing complete all as specified & directed

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other ends with washers 12mm dia and , n exc 5cm long ) complete all as specified and as directed.

M&L for painting two coats of synthetic enamel paint over a coat of red oxide on steel surfaces of any discription over 10cm in width or girth including preparation of new surface

M&L galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanised MS wire staple or steel pins etc as directed (each line wire to be measured.)

Excavation over areas n. exc 1.50 mtr depth and getting out in any type of soil

M&L for broken stone or boulders Hardcore of gauge exc 63 mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface all as specified.

M&L for100mm thick cement concrete 1:4:8 type D-2 (40mm stone agg) as in Subbase

M&L for sand cushioning filling under floors including watering and consolidation.

M&L for Machine pressed Rubberise molded interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 Grade with grey cement and no pigment

Removal of excavated material upto 50 m deposited as directed at a level n exc 1.5m above starting point

M&L for PCC type B1 (1:2:4) as in champher at edges to hold the tiles

M&L for 15mm thick rendering in CM (1:4) in two layers mixed with water proofing compound @ 3% by weight of cement in top 5mm thick finishing the surfaces with fair and even without using extra cement complete all as specified and directed.

Supply only integral WPC

M&L for rendering 10mm thick in cement mortar (1:6) on brick or concrete surface finished even and smooth without using extra cement complete all as specified and directed

M&L for Preparing old/newly plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of alkali resistant primer, complete all as specified and as directed.

M&L for applying two coats of cement base paint over a coat of primer on old/newly plastered surfaces of walls including preparation of surfaces complete.

Dismantling AC/GI/PPGI corrugated or semi corrugated sheets in wall cladding or roof coverings and hanger doors including ridges and make good for aluminium earthing strips after fixing of sheets complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description and in any position complete all as directed by Engr-in-Charge.

S&F Pre- painted galvalume aluminum zinc coating PPGL based corrugated/Trapezoidal steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating PPGL based plain steel sheet 0.60mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, eave board, fixed with self tapping screws, complete all as specified and directed.

Material & Labour for Preparation of new surface applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description over 10 cm wide or girth, complete all as specified and as directed.

S&F MS works as in wind tie for roof flat iron fillet for securing wire mesh etc and similar works conforming to Fe 290-0 Gde E-165 including drilling holes as required all as specified and directed.

Demolition of brickwork or stone/boulder masonry, precast cement concrete block walling in any position, built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L for precast cement concrete (1:3:6) type C1 (using 20mm graded agg) solid block masonry exc 10cm in width or girth and setting in CM (1:6) complete all as specified and directed.

Demolition of RCC of any description and in any position not otherwise specifically provided for including taking out and seperating old reinforcement and removal of debries to a distance not exc 50m as directed by Engineer in charge and making site clean complete all as specified and directed.

M&L for precast RCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in cover slabs, shelves and similar articles set in CM (1:6) including necessary form work complete all as specified and directed.

M&L for Mild steel TMT deformed bars, 5 to 10 mm dia , cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified

Material & Labour screed bed or bedding layer of cement mortar (1:6) ,15 mm thick for laying floor finishes, complete all as specified and directed.

M&L screed bed or bedding layer of cement mortar 1:4 ,10 mm thick for as in vertical surfaces such as skirting , dados etc, complete all as specified and as directed.

M&L for joint free non-skid coloured ceramic tiles 7 to 8 mm thick, area of each tile exc. 0.11 sqm but n exc 0.18 sqm (400mmX400mm), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified

M&L for Coloured Glazed ceramic tiles 300 x 200 x 7 mm thick, set and jointed in neat cement slurry and pointed in white or Coloured cement to match.

Material & Labour PCC 1:2:4 type B1 40mm thick, using 20mm graded stone aggregate as in flooring and finished surface even and fair using extra cement complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 20-25 mm thickness 600x450mm in size over cement screed base laid and jointed with pigment to match the shade of the slab incl rubbing & mirror polishing.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed and jointed with pigment to match the shade of the slab incl rubbing & mirror polishing.

Demolition of cement concrete (unreinforced) in ground floor and pavings n exc 15 cm thickness (below or above ground level) complete .

Material & Labour 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection and finished concrete surface even and smooth without using extra cement including making proper joints with bitumen mastic with sand as per specification at an interval of 3m complete all as specified and as directed.

Cleaning of PVC water tanks of capacity 500 litres including chemical treatment with Anti-bacterial agent consisting of following process: - Dewatering the tank with submersible pump, de-silting and removing of left over dirty water up to 100 to 150 mm in the bottom of the tank and sludge with special sludge pump, cleaning of walls and ceiling with special mechanized high pressure jet machines by rotary jet system at 100-120 Bar pressure (120 Kg /sq cm) which dislodges the layer of dirt, algae, fungus stuck on its surface usage of scrubbing machines for old stains and cleaning chemicals if required of make Eureka Forbes Ltd, floor of the dirty tank should be thoroughly cleaned up by fry jet cleaner to accumulate all dirt ,the remaining sludge should than be removed by sludge pumps, the dirt silt and other foreign material should further be removed by Industrial Vacuum Cleaners to make the floor totally dirt free, application/spraying of Anti-Bacterial chemicals to ensure total sterilization of tank from the inside, inside of the tank should be treated with specially developed 4 ft long ultraviolet Radiator to kill further floating bacteria/virus in order to make the tank totally clean, bacteria free and safe for storage of drinking water. All the above operations should be executed by trained workers and technicians with paint 75 mm height in DD/MM/YY patern and refixing the cover after cleaning all and specified and directed.

Dismantling of steel/iron overhead tank capacity 11500 liters, any section, complete all as specified and as directed. Note: Dismetalled tank shall be deposited in AGE E/M store

Supply and fix in repair rotational moulded,multilayer HDPE water storage tank of 5000 ltrs capacity( tripple layer wall construction , Cylindrical vertical with closed top) ISI marked hoisted and fixed in position all as specified in SSR Part I including 02 Nos 20 mm bore full threaded GI nipple of required size including ball valves 20 mm bore high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed (Minimum weight 20mm - 210gms and refixing of inlet, outlet & over flow pipe etc complete all as specified and as directed.

Schedule of Credit

M/s Mangal Enterprise

M/S C.M.V CONSTRUCTIONS