SPECIAL REPAIRS TO BLDG NO. 77 RECORD OFFICE GRC KAMPTEE.

Amount

Dismantling of asbestos cement/translucent sheet corrugated/ semi-corrugated sheets in roof coverings incl ridges complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed .

S&F for 0.63 mm thick plain galvanised mild steel sheeting using grade’ sheets with 275 gm Zinc (Spelter) coating Per Sqm both sides inclusive, as in ridges, hips, valley gutters, drip, crumple section and straight flashing fixed with ‘L’ or ‘J’ type hook and washers or Nails complete all as specified and directed.

Roughening surfaces of old concrete floor/terrace by picking incl. taking down existing detoriated / decayed tar felt or any treatment including loose surface, scraping with scraper, chiselling, scraping of surface with wire brush or any other method, sweeping clean & washing down with water to remove dust etc. and removing the scraped materials debris to a distance not exc. 50 m. complete all as specified and directed.

M&L for 40mm thick cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate), as in padding, coping etc., laid to proper slope and gradient, using with water proofing liquid compound as per manufacturer instructions, finished even and fair without using extra cement, complete all as specified and directed. Note: Water proofing liquid compound shall be measured and paid separately.

Material & labour for provision of water proofing treatment by using APP torch on mineral/slate finished membrane over roof and vertical surfaces including preparation of surfaces and applying oil based bituminous primer coat @ 0.30 ltr per sq m on clean and dry surface and then providing APP membrane having non woven. polyester film reinforcement with 3 mm thick and weight not less than 3 .00 kg/sq m and finished on top with mineral/slate finished torch on system laid with 100 mm & 150 mm over lap on side & end laps respectably complete all as per manufacturers compound complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including dismantling of ceiling fan, tube light, cable and refixing at same place cover fillets complete all as specified and directed.

Providing and fixing snap grid for false ceiling of size 595 x 595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanised steel sections @ 90 grams/ sqm both side inclusive, consisting of main 'T' runner with suitably spaces joints to get required length and of size 24mm X 38mm made from 0.25 mm thick (minimum) sheet, spaced at 1200 mm centre to centre and cross 'T' of size 24 mm x 25 mm x 1200 mm made of 0.25 mm thick (minimum) sheet, 1200mm long spaced between main 'T' at 600mm centre to centre to form a grid of 1200 x 600mm and secondary cross 'T' of length 600mm and size 24mm X 25mm X 600mm made of 0.25 mm thick (minimum) sheet to be interlocked at middle of the 1200 X 600mm panel to form grids of 600 X 600 mm and wall angle of size 24mm X 24mm X 0.4mm including, required cutting/ making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. main 'T' runners to be suspended from ceiling using GI slotted cleats of size 27 X 37 X 25 X 1.0 mm fixed to ceiling complete all as specified and directed.

M&L for GI adjustable rods with galvanized butterfly level clips of size 85 X 30 X 0.5 mm spaced at 1200 mm centre to centre along main 'T', bottom exposed width of 24mm of all T-sections shall be pre-painted with polyster paint for all heights complete all as specified and directed.

M&L for 4mm thick Non asbestos fibre cement building designer board of size 595mm X 595mm fixed or laid/ inserted to timber/GI/Aluminium framework with screws and fixed in ceiling flat or sloping complete all as specified and directed.

Taking down Chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each (Without taking off shutters from the frame) complete all as specified and directed.

Taking down Chowkats or frames incl. shutters (without taking of shutter from the frames)n. exc 1.50 Sqm each complete all as specified and directed.

Taking down cement plaster, any description on brick or stone walls including raking out joints hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick in cm 1:4 on brick or concrete surfaces using water proofing liquid compound as per manufacturer instructions, and finishing surfaces even & smooth without using extra cement. complete all as specified and directed. (Note : Water proofing compound Liquid shall be measured and paid separately)

Dismantling of brick work or stone/boulder masonary built in cement mortar including ashlar facing dressed stone and pre-cast concrete articles complete all as specified and directed

M & L for brick work with fly ash bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6(Using old size brick) complete all as specified and directed.

Material & labour for Rendering 10 mm thick CM 1:6 on brick or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed.

Material & labour for Rendering 5 mm thick CM 1:3 on brick or concrete surfaces of ceiling /chajja's finished even & smooth without using extra cement complete all as specified and directed.

Material & labour for preparation of new plastered surfaces on wall & applying two coats of cement base paint complete all as specified and directed

M & L for preparation of new surfaces or unplastered surface on wall & applying two coats of oil bound distemper over a coat of birla wall care putty complete all as specified and directed

M & L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparation of existing old decorated plastered wall surfaces and applying two coats of cement base paint complete all as specified and directed.

M&L for preparation of existing old decorated plastered wall surfaces and applying two coats of oil bound distemper over a coat of birla wall care putty complete all as specified and directed.

M&L for preparation of existing old decorated plastered wall surfaces and applying two coats of white wash complete all as specified and directed.

M&L for preparation of existing old decorated plastered wall surfaces and applying two coats of white wash on ceiling complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises up to 1 KM complete all as specified and directed.

M&L for light shade, coloured, vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over 15mm thick screed bed in CM 1:4 complete all as specified and directed.

Ditto all as per item Ser No. 28, but on dados surfaces. including 10mm thick backing coat in CM 1:4 finished even and fair faces complete all as specified and directed.

M&L for coloured glazed ceramic tiles in vertical surface of size 300mm x 450mm x 7mm thick, set and jointed in neat cement slurry and pointed in white or colour cement mixed with pigment to match the shade of tiles including 10mm thick backing coat in CM 1:4 finished even and fair faces complete all as specified and directed.

Material & labour for colour ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc., set & jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15 mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M & L for Machine cut Kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over screed bed or bedding layer of mortar 20 mm thick Cement Mortar 1:6 complete all as specified and directed.

M & L Kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over 10mm thick rendering in cement mortar 1:4 , on fair faces of brick work or concrete surfaces as backing complete all as specified and directed.

M&L for 75 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate ) as in PCC path and similar works complete all as specified and directed .

M&L for chequered rubber moulded cement concrete tiles size 30cm x 30cm x 25 mm thick set ,jointed and pointed in grey cement and pigment and fixed with cement slurry in floors including 20mm thick screed bed or bedding layer of cement mortar 1:4 complete all as specified and directed.

Material & labour plain cement concrete Type 1:2:4 B0 (using 12.50 mm graded stone aggregate) as in coping, haunching rounded or chamfered on edges including necessary from work complete all as specified and directed.

Taking down eaves gutters, gas pipe, sewage pipe and rain water pipes (any size or pattern), including all fittings, heads shoes, bends, swan-necks etc., incl cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings the accessories) complete all as specified and directed.

Supply & fix 100 mm dia cast iron soil waste & vent pipe in any length with or without ears, with cement joints, laid in trenches or in floors, complete all as specified and as directed

Supply & fix 75 mm dia cast iron soil waste & vent pipe any length with or without ears with cement joints, laid in trenches or in floors, complete all as specified and as directed

Supply & fix CI Bends 100 mm bore (any radius) diminishing pieces or tapers(larger bore to be measured) complete all as specified and directed.

Supply & fix CI Bends 75 mm bore(any radius) diminishing pieces or tapers(larger bore to be measured) complete all as specified and directed.

Supply & fixing CI branch pieces, single 100 mm dia (equal or unequal) ordinary or inverted(spigot or socket type) or with parallel branches complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exc 10 cm girth complete all as specified and directed.

Dismantling of water tanks and removing to store exc. 250 ltrs & not exc. 500 ltrs complete all as specified and directed.

Supply, Hoisted and fixed in position rotational moulded polyethylene water storage tanks triple layer (cylindrical with closed top) capacity 500 ltrs complete all as specified and directed.

S & F in repair 20 mm PTMT float valve, high pressure with Polythene float and flynut complete, screwed for Iron pipe etc.,complete all as specified and directed.

S&F in repair gun metal gate valve of 20 mm dia with iron wheel screwed both for iron pipe complete all as specified and directed.

Taking up or down steel tubing and connection, including cleaning for re-fixing or removal of store for 15 mm bore complete all as directed.

All as per item No 48 above, but 20 mm bore, complete all as specified and directed.

Supply & fix GI tubing 15 mm bore ' medium grade ' with all fittings and fixed to wall/ceiling or laid in floors complete all as specified and directed

Supply & fix GI tubing 20 mm bore ' medium grade ' with all fittings and fixed to wall/ceiling or laid in floors complete all as specified and directed

S & F CI Nahani trap 75 mm dia with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) complete all as specified and directed

S&F in repair vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) but including sheet cover and jet section complete all as specified and directed.

Supply only PVC valveless syphonic action type flushing cistern, 10ltr capacity low level, white/coloured with inlet, ball valve, float and handle including bracket(incl.taking down old cistern ) and fixing of PVC flush pipe 32 mm dia and PVC connection pipes complete all as specified and directed.

Supply only flush pipe of polythene of low or high density 32 mm PVC for low level flushing cistern, complete all as specified and directed.

Supply only PVC connection 15 mm dia, 450 mm long including brass ferrules on both ends, complete all as specified and directed.

Supply only low density PVC pipe 32/40 mm dia as in waste pipe to sink complete all as specified and directed

S & F 75 mm bore stack clamp made out of 50x5 mm flat iron and 16 mm dia round iron stays incl bolts & nuts and securing ends of stays to wall , complete all as specified and directed

Ditto as per item 58 above, but 100/110 mm bore, complete all as specified and directed

S&F 15 mm dia Bib taps, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule and fixed completed all as specified and directed

S&F15 mm bore stop valves, cast copper alloy, chromium plated, fancy type screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipes or for Urines and fixed, complete all as specified and directed.

S&F in repair 15mm bore pillar taps, cast copper alloy, fancy type chromium plated screwed down high pressure swan Neck with or without lettered Hot or Cold with long screwed shanks and flynuts, screwed for iron pipes and fixed, complete all as specified and directed.

M&L for Preparation of old wooden surfaces of any description over 10 cm width or girth & applying one coats of synthetic enamel paint complete all as specified and directed.

M & L for preparation of old steel surfaces of any description over 10 cm width or girth & applying one coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed

M & L for preparation of new steel surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed

S&F 35 mm thick plain framed panelled factory made shutter made out of 2nd class hard wood, rail and stiles and panel of 12 mm thick veneered particle board with commercial veneering on both faces or 9 mm thick B.W.P commercial veneering. The size of rail and stile as per IS:1083 (part-I) kiln seasoned an chemically pressure treated of any number of panel, complete all as specified and directed.

M&L two coat of synthetic enamel paint over new wooden surfaces of any description not otherwise described over 10cm in width or girth over one coat of pink primer including preparation of surfaces, complete all as specified and directed.

S & F solid PVC frame of size 50 mm x 47 mm made out of 5 mm wood grain colour PVC sheet reinforced with MS square tube & fixing in opening as per specification & drawing.

S & F PVC factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with wood free EPS 2,4,or 6 raised panel design with 2mm thick Moulded PVC sheet on sheet on the front face & 2mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification & drawing

S& F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

S&F framed guard bars with mild steel square bars with ends of bars shouldered and/ or riveted and similar work confirming to FE 410-O or FE 310-0 complete all as specified and directed

M&L for mild steel 25 x 5 mm flat iron for hold fast complete confirming to Fe-410 -O etc., complete all as specified and directed.

S & F 100 mm long Mild steel medium weight cold rolled butt hinges and fixed with screw/welded to frames etc all as specified and as directed

S&F 150 mm Extruded Aluminium handles fabricated type anodised etc complete all as specified and directed

S & F 250 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed, complete all as specified and directed.

S & F 150 mm long aluminium anodised, barrel tower bolt of extruded section complete all as specified and directed

Hacking out old broken glass (any thickness) size and quality or description from wooden/steel frames etc complete all as specified and directed

S & F sheet glass ordinary quality, 3 mm thick and glazing with oil putty in square n. exc. 0.50 Sqm in each pane complete all as specified and directed

S & F 3 mm figured glass, pin head type and glazed with oil putty in sqm n exc 0.50 sqm in each pane complete all as specified and directed

Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level), complete all as specified and directed.

M & L for 75 mm thick Cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection with fair finished complete. Note : Joints 12mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be paid separately.

Forming 12 mm thick expansion joint with pre-formed filler and top 30 mm primed and sealed with sealing compound Grade ‘A’ all as specified for thickness of concrete, complete all as specified and directed.

Demolition of re-inforced cement concrete in any position not otherwise specifically provided for, complete all as specified and directed.

M&L for RCC Type A1 1:1/2:3 (using 20mm graded stone aggregate) as chajja, facia, parapets fin louvers, coving with water proofing compound etc complete all as specified and directed.

M&L for precast RCC Type B1 1:2:4 (using 20mm graded stone aggregate) cover slab for crumple sections, bed pates, anchorage blocks, brackets etc.on roof set in CM 1:4 complete all as 'specified and as directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape as required incl cranking, bending for hooping columns, hooking ends and binding with MS wire (annealed) not less than 0.9 mm dia or securing with clips as in reinforcement. For strengthening of wall at places, complete all as specified and as directed.

Ditto all as per item Sr.No. 87 above, but 8mm dia bars, complete all as specified and as directed.

M&L for formwork to sides of pillars, lintel and chajjas incl fair finished surfaces of concrete, square ,rectangular for fair finished surfaces, complete all as specified and as directed.

M&L for Vitreous China Urinal, Half stalI type, white (excluding flushing cistern, flush pipe and waste pipe) complete all as 'specified and as directed.

S&F vitreous china counter sunk, oval type, wash basin, 550 mm in length including cutting for and pinning in ends brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as 'specified and as directed.

M&L for pre- polished granite slab machine cut of any shade as approved by GE 20 mm thick including necessary notching, chamfering the edges over cement screed bed including Cutting, Grinding and Mirror polishing(Granite finish) with suitable grinding stones complete all as 'specified and as directed.

M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platforms, and other similar situations, complete all as specified and as directed.

S&F PVC (SWR) Rain water pipes,110mm dai, single socketed, with or without ears in any length with rubber ring joints fixed to walls complete all as specified and as directed.

M&L for 20mm thick plaster in CM 1:3 on concrete surfaces of sunken floors mixed with liquid water proofing compound finished even and smooth using extra cement Note : Liquid water proofing liquid shall be measured and paid separately and applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg per sqm incl. cleaning surfaces complete all as specified and directed.

M&L for PCC 1:5:10, type E2 (using 40 mm graded stone aggregate) as in mass concrete, filling in sunken floors, complete all as specified and as directed.

Supply only liquid water proofing compound complete all as specified and as directed.

M&L for sealing crackers on plaster, masonry and concrete surface using V grooves system Rendercos CS 1 kg of mixed material covers 30 Rm for a groove size 6mm x 6mm (make- Fosroce), complete all as specified and as directed.

S & F galvanised mild steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks or galvanised wire staples, complete all as specified and as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc., complete all as specified and as directed.

Supply & Fixing only Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc FE 410 w (Gde E-250) quality 'A', complete all as specified and as directed.

S&F steel window with side hung shutters (glaze & gauze shutter) including projecting or box type hinges with steel handle peg stay and divided into square with glazing bars dovetailed or welded, to receive glazing, or gauzing including one coat of primer including fixing of hold fast of size 25 x 5 mm flat iron etc complete all as specified and directed.

S&F in repair steel window handles with nuts & bolts or with screws complete all as specified and directed.

S&F in repair steel window peg stay and hinges all as specified and directed.

S & F 4 mm thick sheet glass, ordinary quality and glazing plain/tinted with rubber gasket in square exceeding 0.5 Sqm in each pane, complete all as specified and directed.

Removing building materials to a distance of 100m or under, beyond the lead incl in the rates incl loading, unloading and stacking at the destination, complete all as specified and as directed.

S&F anodized aluminium powder coated (minimum thickness of powder coating 50 micron) frames for in doors, windows and ventilators opneble or sliding any type etc with one or more rebates including necessary jointing cleats for fixing etc., complete all as specified and as directed by Engineer-in-Charge.

Excavation in trenches for laying of cables, poles and stay in any type of soil not exceeding 1.5 mtr wide and not exceeding 1.50 mtr deep and getting out, complete all as specified and as directed.

Returning filling in, including spreading, leveling watering and well ramming in layers not exceeding 25 cms thick as specified and directed by Engineer in Charge.

Removing excavated materials not exceeding 50 Mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point, complete all as specified and as directed.

Taking down point wiring with aluminum conductor cable of light point fan & socket light & power complete including light fittings any type switches, sockets, ceiling rose, switch boards, bell/buzzer, bell push, tube light fitting, regulator etc, and making good to the disturbed surfaces of walls/ floor etc to match with existing surfaces including white washing/colour washing/ distemper to match with existing wall/floor/ceiling finishes, complete all as specified and as directed.

Taking down sheet metal enclosure DB, MCB, main switch etc and making good disturbed surfaces to match with existing surfaces, complete all as specified and as directed.

Taking down sub main wiring of any size/ capacity complete all as specified and making good disturbed surfaces to match with the existing surfaces, complete all as specified and as directed.

M&L point wiring 1100 volt grade single core FRLSH PVC insulated and unsheathed cable with multistranded copper conductor 1.50 sqmm drawn in and including electrical grade PVC conduit not less than 20mm dia with IS 9537 (Part-III) 1983 marked medium grade concealed on surface of wall/ceiling including FRLSH PVC insulated unsheathed earth wire with multistranded copper conductor of size 1.50 sqmm pressed steel modular boxes sunk on wall for mounting of modular switches, switch sockets, fan regulator etc including modular cover with frame any size complete all as specified and making good disturbed surfaces for one light point controlled by one, one way switch.(Cable Make : Finolex, L&T, Legrand, Havells, Polycab) (PVC Conduit Make : Polycab, Anchor, Finolex) Note :- Cost of cable provided from sub main DB to respective switch board in rooms shall be included in the quoted point wiring rate. All switches, fan, sockets, ceiling roses and holders shall be connected to common earth dolly.

Ditto all as per item Sr. No. 114 above but One ceiling /exhaust fan point controlled by one switch and regulator, complete all as specified and as directed.

Ditto all as per item Sr. No. 114 above but One 3 pin 5 amp socket out point on the same board with other switches, complete all as specified and as directed.

Ditto all as per item Sr. No. 114 above but One 3 pin 5 amps socket out let point on independent board, complete all as specified and as directed.

Ditto all as per item Sr. No. 114 above but One bell/buzzer point controlled by one bell push, complete all as specified and as directed.

Ditto all as per item Sr. No. 114 above but wiring with 4.0 sqmm multi stranded cable and earth wire with copper conductor of size 4.0 sqmm for 15 amps power point, complete all as specified and as directed.

Ditto all as per item Sr. No. 114 above but wiring with 2.5 sqmm multi stranded cable and earth wire with copper conductor of size 2.5 sqmm for 15 amps power point, complete all as specified and as directed.

M&L for sub main wiring with two single core PVC FR LSH insulated unsheathed stranded copper conductor and earth wire 1100 volt grade and drawing into PVC conduit not less than 20 mm medium grade concealed in wall of the following sizes :- 2x10.0 Sqmm with earth wire of 1x10.0 Sqmm. (Cable Make : Finolex, L&T, Legrand, Havells, Polycab) (PVC Conduit Make : Polycab, Anchor, Finolex) Note :- Accessories for point/sub main wiring like PVC junction box, bend, Tee, elbow shall be of same make.

Ditto all as per Sr. item No. 121 but 2x 6.0 Sqmm with earth wire of 1x6.0 Sqmm, complete all as specified and as directed. Note: rates deemed to include connection between 3 phase ducting cooler motor and DOL starter.

Supply and fix ceiling rose surface type 2/3 terminal 5 amps, complete all as specified and as directed. Make : Anchor Roma, Legrand, Crabtree, complete all as specified and as directed.

S&F Bell ding dong, AC 230 volts, single phase, complete all as specified and as directed.

Supply and fix Modular switch one way 6A, 1 module, complete all as specified and as directed. Make : Anchor Roma, Legrand, Crabtree

Supply and fix Modular bell push 6A, 1 module , complete all as specified and as directed. Make :Anchor Roma, Legrand, Crabtree

Supply and fix Modular Socket 6A 2/3 pin combined 2 module , complete all as specified and as directed. Make : Anchor Roma, Legrand, Crabtree

Supply and fix Modular Fan step regulator,120 watt 2 module, complete all as specified and as directed. Make : Anchor Roma, Legrand, Crabtree

Supply and fix Modular switch one way 16A, 1 module , complete all as specified and as directed. Make : Anchor Roma, Legrand, Crabtree

Supply & Fix Modular Socket 6A/ 16A 2/3 pin combined 2 module , complete all as specified and as directed. Make : Anchor Roma, Legrand, Crabtree

Replacement of worn out MS AC plug box with modular plate power unit four module, 20 Amps starter, 25 Amps sockets, 25 Amps plug, complete all as specified and as directed. Make: Legrand/ Schenieder / Crabtee.

Supply and Fix Highly durable surface mounted 18/20 watts LED batten/surface constructed of fire retardant engineering grade extruded plastic and decorative end cap complete with tube rod,driver including 3 core 1.0 sqmm copper conductor cable for connection and accessories, complete all as specified and as directed. Make :- CG LCTLN-20-CDL/cat No BLTRU 20W NW VIVA of Bajaj/ BN150W LED20S-6500 PSE OD GR of Philips.

Supply & fix light fitting 9W bulk head luminaries with lamp holders etc complete with all accessories and including connecting up with twin core twisted flexible cable suitable size of 230V, 50HZ , complete all as specified and as directed. Make: CG LBHP-10-CDL/ Philips/ Wipro.

Supply and fix Energy efficient surface mounted 2'X2' grid Ceiling LED fitting 36/40 W rated voltage 240 V, 50Hz combination with profiled and flat diffuse, complete all as specified and as directed by Engineer-in-Charge. Make : CG LCTLRF6-36-CDL/ Philips/ Wipro.

Supply and fix LED baton fitting 2' length including drivers having energy consumption, 10/11W ,230 V ,50Hz, 6500K, not less than 800 lumen prewired, complete all as specified and as directed by Engineer-in-Charge. Make : CG LCTLN-10-CDL/ Philips/Wipro.

Supply and fix building security light LED 25 W with Lumen O/P 1800 with driver with rated voltage 240 V, 50Hz,including mounting GI (made out of 25 mm dia light grade pipe 0.8 m bent two shape including FI clamps nut bolts etc., complete all as specified and as directed by Engineer-in-Charge. Make : CG LSTS-25-CDL-M/ Philips/ Wipro.

Supply and fix sheet metal enclosure vertical triple pole & neutral(VTPN) with MCCB 100 amps for 415 volts 4 way with 200 Amp rated bus bar flush /surface mounting double door, complete all as specified and as directed by Engineer-in-Charge. Make-Legrand/ Siemens/ Schneider

Supply and fix sheet metal enclosure single pole & neutral for 240 volts 8 way with 200 Amp rated bus bar flush /surface mounting double door, complete all as specified and as directed by Engineer-in-Charge. Make-Legrand/ Siemens/ Schneider

Supply and fix MCB single pole 240 volt 6 to 40 amps 10 KA breaking capacity, 'C' series , complete all as specified and as directed by Engineer-in-Charge. Make-Legrand/ Siemens/ Schneider

Supply and fix MCB single pole and neutral 240 volt 6 to40 amps 10 KA breaking capacity, 'C' series,, complete all as specified and as directed by Engineer-in-Charge. Make-Legrand/ Siemens/ Schneider

Supply and fix MCB triple pole and neutral 415 volt 40 to 60 amps 10 KA, complete all as specified and as directed by Engineer-in-Charge. Make-Legrand/ Siemens/ Schneider

S & F Exhaust fan single phase,200/230 mm sweep, metallic with bolts, nuts, washers and connected electrically, complete all as specified and as directed by Engineer-in-Charge. Make : Orient/ Havells/ Crompton.

Taking down carefully ceiling fan with down rod complete of 1200/1400 mm sweep from fan hook dismantling blade complete, cleaning, servicing, painting with two coat of enamel paint, marking MES number & refixing & connecting with 3 core copper cable, complete all as specified and as directed by Engineer-in-Charge.

Earthing complete with galvanized street earth plate electrode 600x600x6mm thick buried directly in ground (earth plate not less than 2.25mtr deep below normal ground level) with top edge of the plate not less then 1.50 mtr. below the normal ground level connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washer of galvanized iron or steel all as shown in electrical plate No 5 connected to earthing test point all as specified and testing on completion including the material and labour for :-(a) Excavation and earth work or drilling hole for electrode in any type of soil (b) PCC pit in cement concrete 1:2:4 TYPE B-1 (.c) Pre cast RCC cover with suitable handle 40mm thick in PCC 1:2:4 reinforced with welded steel wire fabric weighting not less than 1.87 Kg/sqmm (d) Funnel with watering pipe of GI 20mm nominal bore medium grade and Aluminum lugs etc all as specified.(e) 15mm nominal bore medium grade GI protection pipe up to 7.50 meter long for protection of earthing lead.(f) Requisite quantity of charcoal and common salt (g) Connection to earthing test point and testing on completion.

S&F Air Circulator fan 450mm sweep, 250V, 50 HZ complete with all fittings all as specified and directed. Make: Orient/ Havells/ Crompton.

S&F 3 phase trunking bus bar panel with 200 amp aluminium bus bar flush mounted complete connecting with existing supply, complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repairs Rigid non metallic 25 mm dia PVC conduit inclusive of boxes ,Junction/terminal all tees, bend,elbow,reducers,bell mouth tube ends and fixing accessories such as couplers, lock nuts,saddles,pipes hook etc concealed on surface on wall and making good including taking down existing TV, Telephone, Signal cables and re used in given non metallic PVC conduit , complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repairs Rigid non metallic 32 mm dia PVC conduit inclusive of boxes ,Junction/terminal all tees, bend,elbow,reducers,bell mouth tube ends and fixing accessories such as couplers, lock nuts,saddles,pipes hook etc concealed on surface on wall and making good including taking down existing TV, Telephone, Signal cables and re used in given non metallic PVC conduit, complete all as specified and as directed by Engineer-in-Charge.

Supply and fix Double wall Corrugated High Density Polymer Ethyl (HDPE) pipe for laying of Electric cable of size 50 mm outer diameter and 38 mm inner Diameter with IS 14930 (part 2) 2001 and 6 mm thickness laid in trenches,wall, floor , pole including bends, sockets and other connected accessories, complete all as specified and as directed by Engineer-in-Charge. Make: Ketron/ Tirupati.

Supply and laying in trenches or fixing in walls / poles or drawing through pipe XLPE insulated, screened,PVC bedded, galvanised steel strip or wire armoured,electric power cables ( heavy duty) with aluminium conductor, 1100 volts, grade cross sectional area 10 sq mm, 4 core including testing after laid and jointed, complete all as specified and as directed by Engineer-in-Charge. Make: Polycab/ Havells/ Finolex.

Supply & install steel octagonal decorative poles 5 mtrs long complete with cast iron base plate,bolts,nuts and screws complete fixing on foundation with anchor bolts and nuts as specifide and as directed including plain cement concrete 1:3:6 type C -2 using 40 mm graded stone aggregate as in foundation filling and mass concrete for stay ,poles etc, complete all as specified and as directed by Engineer-in-Charge. Note: Dimensions of foundation concrete will be (LXBXD) : 0.5m X 0.5m X 1.5m below ground level and 0.5m X 0.5m X 0.3m above ground level.

Supply and fixing thermoplastic cable junction boxes IP 55/IP65 with metric knockout for cable entry of size 200 x 160 x98 mm fixing on pole with 30 x 5 mm MS clamps, nut bolts, washers, terminal block and glands suitable for 16 Sq mm core cable including 6 amps MCB SPN, complete all as specified and as directed by Engineer-in-Charge. Make:- HENSEL, Neptune, Sintex, Legrand.

Supply and fix 3 core 1.5 sqmm PVC insulated PVC sheathed weather proof multistranded Copper conductor cable 1100 volts grade drawn through in GI conduit,on pole, complete all as specified and as directed by Engineer-in-Charge.

Supply and fix LED flood light luminaires of capcity 120 watts with pressure die cast aluminium housing heat resistance toughened glass, IP 66 protection complete with driver, with suitable size Flat Iron clamps, nuts, bolts, washers and fixing accessories including taking down old unserviceable fitting, complete all as specified and as directed by Engineer-in-Charge. Make :- Cat No.LFLN-120-CDL/60-M of CG / Philips, Bajaj.

NOTE :- SCHEDULE OF CREDIT (Amount shall be deducted offline from the total quoted amount to workout the net contract sum to be considered for acceptance.) [(-) Rs.48,684.00 /- ]

M/s T.S.JOHAR

SHUB CONSTRUTION

MVN Enterprises

Meet Road Lines

DE PRETTY AND CO

Vishwakarma Engineering Works

khushal constructions

Bidder Name

Meet Road Lines

DE PRETTY AND CO

Vishwakarma Engineering Works

MVN Enterprises

chronicle enterprises

SHUB CONSTRUTION

M/s T.S.JOHAR

khushal constructions