AS-12-774

MRL02-Langmepi Rongkimi Gaon to Arnam Anglong Gaon AS-12-774

Item Rate BoQ

BoQ_Ver3.0

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201.[SOR 20-21] [Item No. 2.2(i-a)] i. By Manual Means (A) In area of non thorny jungle

Removing all types of Hume pipes and stacking within a lead of 1000 m including Earthwork and Dismantling of Masonry Works as per Technical Specification Clause 202. (A) Upto 600 mm dia Hume pipe

Excavation in Ordinary Soil Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections.

Construction of Embankment with material obtained from Borrow Pits, Construction of embankment with approved materials obtained from borrow pits with a lift up to 1.5m, transporating to site, spreading, grading to required slope and compacting to meet required of Tables 300.1 and 300.2 with a lead upto 1000m as per technical specification clause 301.5. (i) Private land

Construction of sub-grade and earthen shoulders Construction of sub-grade and earthen shoulders with approved materials obtained from borrow pits with all lifts and leads, transporating to site, spreading, grading to required slope and compacting to meet required of Table 300.2 with lead upto 1000m as per technical specification clause 303.1 (a) Private land

Construction of Granular sub-base (A) By mix in Place Method, Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. (II) For Grading Material (Gr - II )

Water Bound Macadam (II) WBM Grading 2 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per Technical Specification Clause 405. Using stone screening Type-B 11.2 mm for Gr.II: (A) By manual Means

(III) WBM Grading 3 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per Technical Specification Clause 405. Using stone screening Type-B 11.2 mm for Gr.III: (A) By manual means

Prime-Coat (i) Low porosity Providing and applying primmer coat with bitumin emultion (SS-1) on prepared surcafe of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per technical Clause 502.

Tack-coat (III) Providing and applying tack coat with bitumin emultion (RS-1) using emultion distributor at the rate of 0.25-0.30 Kg/sqm on the prepared granular surface tresated with primer & cleaned with hydraulic broom as per technical specification clause 503.

Mix Seal Surfacing Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9mm (Type-A) or 13.2 mm to 0.9mm (Type-B) aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification Clause 509 Using Cold Mix Binder

Kilometer Stone Reinforce cement concreter M15 grade kilometer stone of standard design as per IRC:8 fixing in position including painting and printing etc. as per drawing and technical specification clause 1703 (ii)Ordinary Kilometer Stone (precast)

Kilometer Stone Reinforce cement concreter M15 grade kilometer stone of standard design as per IRC:8 fixing in position including painting and printing etc. as per drawing and technical specification clause 1703 (iii) 200 m Stone (precast)

Providing and Fixing 'Logo Board' of PMGSY Project Providing and fixing of typical logo board with PMGSY logo as per MORD specifications and drawing. 1 nos. 1.6mm thick MS sheet duly welded with 5mm thick steel plate on back on edges. The 1 nos. steel plate will be welded horizontally with 1 nos. 75mm x 75mm of 12 SWG sheet tubes posts duly embeded in cement concrete M15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The 1 no. steel plate will be welded vertically to 1 no. 75mm x 75mm of 12 SWG sheet tubes posts duly welded to vertical tubes. All MS will be stove enameled on both sides. Lettering and printing arrows, borders etc. will be painted with ready mixed synthetic emnamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted and two coats of epoxy paint as per specification clause 1701 and Annexure 1700.1

Providing and Fixing Title information Board of PMGSY Project Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6mm thick, top and middle plate duly welded with MS flat iron 25mmx5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mmx25mmx5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2nos. 75mmx75mm of 12SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mmx450mmx600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mmx47mm of 12SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Providing and fixing of typical Citizens Information Board and Maintanance Information Board with Logo as per MORD specifications and drawing. Two nos. 1.6mm thick MS sheet duly welded with 5mm thick steel plate on back on edges. The 4 nos. steel plate will be welded horizontally with 2 nos. 75mm x 75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 600mm x 600mm x 750mm, 750mm below ground level. The 2 nos. steel plate will be welded vertically to 2 nos. 75mm x 75mm of 12 SWG sheet tubes posts duly welded to vertical tubes. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and coloue. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Traffic - Signs A. Retro-reflectorised Traffic Signs (II) Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 1.5 mm thick supported on GI Pipe 50mm dia firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawing and Technical Specification Clause 1701 (i) 900 mm equilateral triangle

Traffic - Signs A. Retro-reflectorised Traffic Signs (II) Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 1.5 mm thick supported on GI Pipe 50mm dia firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawing and Technical Specification Clause 1701 (iii) 600 mm circular

Traffic - Signs A. Retro-reflectorised Traffic Signs (II) Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 1.5 mm thick supported on GI Pipe 50mm dia firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawing and Technical Specification Clause 1701 (iv) 600 mm x 450 mm rectangular.

Painting lines, Dashes, Arrows, etc. on Road in Two Coats on New Work Painting lines, dashes, arrows, etc. on roads in two coats on new work with ready mixed road marking paint conforming to IS:164 on bituminous/concrete surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control as per drawing and Technical Specification Clause 1702

Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface Providing and laying of hot applied thermoplastic compound 2.5mm thick including reflectorising glass beads @250gms per sqm area, thickness of 2.5mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes and conforming to the MoRT&H specifications (a) Edge Line (100mm Width,On Both Side)

Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface Providing and laying of hot applied thermoplastic compound 2.5mm thick including reflectorising glass beads @250gms per sqm area, thickness of 2.5mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes and conforming to the MoRT&H specifications (b) Diagonal and Chevron marking

Providing and laying Speed Breaker

'Earthwork in excavation for structures in all types of soil excluding rock, including all lifts and leads complete as per drawings and Technical Specifications Clause No.304.

Providing and laying in position Plain Cement Concrete of Grade M 15 in leveling course below foundations, Bedding and cradle for pipe culverts complete as per drawings and Technical Specifications Sections 1500, 1700 and 2700.

'Providing and laying in position Plain Cement Concrete grade M20 in foundation, wing wall and return wall complete as per drawings and Technical Specifications Sections 1500, 1700, 2100 and 2200.

'Providing and Supply of RCC Hume pipe Providing and laying reinforced cement concrete pipe NP4 for culverts as per design on first class bedding of granular material in single row includin fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause1106.

Providing and laying boulder apron for bed protection with stone boulders of minimum size and weight as per Table 1300.1, no fragment weighing less than 25 kg laid dry complete as per drawing and technical specifications Clause 1301

'Plastering with cement mortar (1:3 ) on stone masonry work in sub-structure as per Technical specifications (MoSRT&H Ref. No. 1300 & 2200)

Providing & fixing Weep Holes in head wall, Return wall, wing wall and Retaining wall complete as per drawings and Technical Specifications Clause 2706.